sauermann FG 110 Omaniku manuaal

sauermann
Bränd
sauermann
Mudel
FG 110
Tüüp
Omaniku manuaal
123
4 5
Gas leak detector
USER MANUAL
Description of the device
1. Backlight key
2. OK key
3. On/Off/Esc key
4. Select key
5. Hold/min/max key
FG 110
Technical specications
General features
Measurement units ppm, %vol, %LEL
Measuring element Semiconductor sensor
Display
4 lines, LCD technology. Dimensions 50 x 36 mm
2 lines of 5 digits with 7 segments (value)
2 lines of 5 digits with 16 segments (unit)
Probe Flexible, 300 mm
Housing ABS, protection IP54
Keypad 5 keys
European directives 2014/30/EU EMC; 2014/35/EU Low Voltage; 2011/65/EU RoHS II; 2012/19/EU WEEE
Power supply 4 batteries AAA LR03 1.5 V
Battery life 20 hours
Ambience Neutral gas
Conditions of use (°C, %RH, m) From 0 to +50 °C. In non condensing conditions. From 0 to 2000 m.
Storage temperature From -20 to +80 °C
Auto shut-off Adjustable from 0 to 120 min
Weight 295 g
Accuracy(1) Measurement range in CH4Resolution
20% of full scale
From 0 to 10,000 ppm
From 0 to 1% vol
0 to 20% LEL
1 ppm
0.001% vol
0.001% LEL
(1) All the accuracies indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same conditions, or carried out with calibration compensation.
% LEL: is the limiting concentrations of gas (in air) that is needed for the gas to ignite and explode.
Example for CH4 gas: 100% LEL = 5% vol
% vol: is the concentrations of gas (in air) expressed in percentage of volume in air.
Example for CH4 gas : 1% vol = 10 000 ppm
• Turn on the device by pressing on “On/Off/Esc”.
The device displays its name “FG110”.
When it turns on, the device emits a beep then performs a pre-heating phase. This phase lasts 60 seconds. The count of
this pre-heating time displays on screen.
• During the normal functioning, in the absence of gas leak, the device emits a regular beep*.
• Otherwise, if the device detects the presence of gas, the repetition frequency of the beep will increase as the detected
concentration increases.
Perform a measurement
*The alarm must be activated so that the device emits beeps (see p.3 for the alarm activation).
During a measurement :
• Press once on “Hold/min/max”.
“Hold” appears on screen and the measurement is frozen.
• Press on “On/Off/Esc” to exit the hold function.
The device returns to the measurement display.
Freeze the measurement
Once the measurement is frozen :
• Press on “Hold/min/max”.
The device displays the maximum value measured since the last questioning at the top of the screen and the minimum
value measured since the last questioning at the bottom of the screen.
• Press on “On/Off/Esc” to return to the measurement display.
Display the minimum and the maximum
Adjust the device
Device drop-down menu
The device is on and displays the measurements.
• Press on “Select”.
“UNIT“ blinks on screen.
• Press on “OK”.
The unit currently used blinks on screen.
• Press on “Select” until the desired unit appears: ppm, %VOL, %LEL.
• Press on “OK” to validate the unit selection.
• “UNIT” blinks on screen.
• Press on “On/Off/Esc” to return to the measurement display.
Select the measuring unit
The device is on and displays the measurement.
• Press on “Select” until “AUTO OFF“ blinks on screen.
• Press and “OK”.
The time before the device auto shut-off blinks at the bottom of the screen.
• Press on “Select” until the required time before auto shut-off appears: 15, 30, 45, 60, 75, 90, 105, 120 minutes or OFF.
• Press on “OK” to validate.
“AUTO OFF” blinks on screen.
• Press on “On/Off/Esc” to return to the measurement.
Adjust the auto shut-off
The device is on and displays the measurement.
• Press on “Select” until “BEEP” blinks on screen.
• Press on “OK”.
“OFF” or “ON” blinks on screen.
• Press on “Select” to activate the keys beep “ON” or deactivate it “OFF”.
• Press on “OK” to validate.
“BEEP” blinks on screen.
• Press on “On/Off/Esc” to return to the measurement.
Activate or deactivate the keys beep
This function allows to activate an alarm. When the device detects a leak, it emits a beep whose frequency is increasingly
fast as and when the concentration increases and gets closer to dened alarm threshold. The beep becomes continuous
when the device reaches and exceeds this threshold. This threshold is between 1000 and 10 000 ppm.
The device is on and displays the measurement.
• Press on “Select” until “AL 1” blinks on screen.
• Press on “OK”.
A succession of 5 zeros displays and the rst zero blinks.
• Press on “Select” to select the rst digit value : 0, 1 or Off.
• If 1 is selected, the maximum threshold (10 000 ppm) is reached. Press on “OK” until “AL 1” blinks on screen.
• If Off is selected, the alarm is deactivated. Press on “OK” to validate, “AL 1” blinks on screen.
• If 0 is selected, the following digit blinks. Press on “Select” to select its value, then press on “OK”. The following digit
blinks, perform the same procedure. Press on “OK” when the last digit value is selected, “AL 1” blinks on screen.
• Press on “On/Off/Esc” to return to the measurement display.
Adjust the alarm
NT_EN – FG110 – 07/10/22 – Non-contractual document – We reserve the right to modify the characteristics of our products without prior notice.
www.sauermanngroup.com
• Remove the front part at the back of the device.
• Change the old batteries by AAA LR03 1.5V batteries.
• Replace the front part.
Change the batteries
The device is on.
• Press on “Backlight” to activate the device backlight.
• Press again on this key to deactivate the backlight.
Activate the backlight
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

sauermann FG 110 Omaniku manuaal

sauermann
Bränd
sauermann
Mudel
FG 110
Tüüp
Omaniku manuaal
Laadige alla PDF
aruanne

teistes keeltes

Seotud paberid

Muud dokumendid