sauermann LV 130 Omaniku manuaal

Bränd: sauermann

Mudel: LV 130

Tüüp: Omaniku manuaal

Vane probe thermo-anemometer

USER MANUAL

Description of the device

1. OK key

2. Backlight key

3. Select key

4. On/Off/Esc key

5. Hold/min/max key

LV 130

Technical specications

General features

(1) Battery life given at 20 °C with alkaline batteries.

(2)All the accuracies indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same conditions, or carried out with calibration compensation.

Measuring elements Air velocity: Hall effect sensor / Ambient temperature: NTC

Display

4 lines, LCD technology. Dimnsions 50 x 36 mm.

2 lines of 5 digits with 7 segments (value)

2 lines of 5 digits with 16 segments (unit)

Vane diameter Ø 100 mm

Housing ABS, protection IP54

Keypad 5 keys

European directives 2014/30/EU EMC; 2014/35/EU Low Voltage; 2011/65/EU RoHS II; 2012/19/EU WEEE

Power supply 4 batteries AAA LR03 1.5 V

Battery life 58 hours(1)

Ambiance Neutral gas

Conditions of use (°C, %RH, m) From 0 to +50 °C. In non condensing conditions. From 0 to 2000 m.

Operating temperature (probe) From 0 to +50 °C

Storage temperature From -20 to +80 °C

Auto shut-off Adjustable from 0 to 120 min

Weight 390 g

Parameters Measuring units Accuracy(2) Measuring range Resolution

Air velocity m/s, fpm, km/h From 0.3 to 3 m/s: ±3% of reading ±0.1 m/s

From 3.1 to 35 m/s: ±1% of reading ±0.3 m/s From 0.3 to 35 m/s 0.01 m/s

0.1 m/s

Airow m³/h, cfm, l/s, m³/s ±3% of reading ±0.03 x area (cm²) From 0 to 99 999 m³/h 1 m³/h

Temperature °C, °F ±0.4% of reading ±0.3 °C From 0 to +50 °C 0.1 °C

Once the measurement is frozen:

• Press once on "Hold/min/max".

The device displays the maximum value of velocity or airow measured since the last questioning at the top of the

screen and the minimum value of velocity or airow since the last questioning at the bottom of the screen.

• Press once on "Hold/min/max".

The device displays the maximum value of temperature measured since the last questioning at the top of the screen and

the minimum value of temperature measured since the last questioning at the bottom of the screen.

• Press on "On/Off/Esc" to exit the hold function.

The device returns to the measurements display.

Display the minimum and the maximum

• Turn on the device by pressing on "On/Off/Esc".

The device displays its name "LV130".

• Put the probe to the required location.

The device displays the velocity and temperature measurements.

Perform a measurement

During the measurement:

• Press once on "Hold/min/max".

"Hold" appears on screen and the measurement is frozen.

• Press on "On/Off/Esc" to exit the hold function.

The device returns to the measurement display.

Freeze the measurement

The device is on and displays the measurement:

• Press on "OK".

"START" displays on screen.

• Press on "OK", the average calculation is launched, "END" displays on screen and "AVG" blinks.

• Press on "OK" to stop the average calculation, the average displays.

• Press on "OK" to display the maximum and minimum values measured during the calculation of this average.

• Press on "On/Off/Esc" to exit the average function and return to the measurement display.

Perform an average in velocity

It’s possible to display and measure the airow in place of velocity.

The device is on and displays the velocity and temperature measurement.

• Press on "Select".

"MODE" blinks on screen.

• Press on "OK".

"VELO" blinks at the bottom of the screen.

• Press on "Select" to select the "FLOW" mode then press on "OK" to validate.

"CIRC" blinks on screen, press on "Select" to make appear "K 25 85" then "RECT".

• Press on "OK" to validate.

If "RECT" or "CIRC" are selected, the measuring unit of the duct type displays.

• Press on "Select" to select the unit : mm or inch then press on "OK" to validate.

• If the type of selected duct is circular: "DIAM" displays and the rst digit blinks.

Press on "Select" to select its value then press on "OK" to validate. Perform the same procedure to select the value

of the following digits (to return to the previous digit press on "On/Off/Esc"). When the last digit is adjusted, press on

"OK" to validate. The device return to the display of airow and velocity measurements.

• If the type of selected duct is rectangular: "LENGT" displays and the rst digit blinks.

Press on "Select" to select its value then press on "OK" to validate. Perform the same procedure to select the value of

following digits (to return to the previous digit press on "On/Off/Esc"). When the last digit is adjusted, press on "OK".

Display and measure the air ow

Adjust the device

Device drop-down menu

Select the measuring unit in velocity

The device is on and in velocity mode.

• Press on "Select" until "UNIT" blinks on screen with the velocity unit displayed below.

• Press on "OK".

The unit currently used blinks on screen.

• Press on "Select" until the required unit appears : m/s, fpm or km/h.

• Press on "OK" to validate the unit selection.

"UNIT" blinks on screen.

• Press on "On/Off/Esc" to return to the measurement display.

"WIDTH" to adjust the width, displays on screen, perform the same procedure to select the digits value, when the

last digit is adjusted press on "OK" to validate. The device returns to the display of the airow and temperature

measurements.

• If "K 25 85" is selected: the device returns to the measurements display.

The length, the width and the section diameter are adjustable from 1 to 3000 mm.

Select the measuring unit in airow

The device is on and in velocity mode.

• Press on "Select" until "UNIT" blinks on screen with the airow unit displayed below.

• Press on "OK".

The unit currently used blinks on screen.

• Press on "Select" until the required unit appears: m3/h, L/s, cfm or m3/s.

• Press on "OK" to validate the unit selection.

"UNIT" blinks on screen.

• Press on "On/Off/Esc" to return to the measurement display.

NT_EN – portable-LV130 – 10/06/14 – Non-contractual document – We reserve the right to modify the characteristics of our products without prior notice.

www.sauermanngroup.com

The device is on.

• Press on "Backlight" to activate the device blacklight.

• Press again on this key to deactivate the backlight.

Activate the blacklight

• Remove the front part at the back of the device.

• Change the old batteries by AAA LR03 1.5V batteries.

• Replace the front part.

Change the batteries

Select the measuring unit in temperature

The device is on and display the measurements.

• Press on "Select" until "UNIT" blinks on screen with the temperature unit displayed below.