Smithco Spray Star 3187/3188 Rate-Sync Kasutusjuhend

Bränd: Smithco

Mudel: Spray Star 3187/3188 Rate-Sync

Tüüp: Kasutusjuhend

Spray Star 3187/3188

SharpShooter-Rate Sync w/ Raven 440

with 18’ and 20’ Booms

July 2016

Operator’s

Product Support: Hwy SS & Poplar Ave; Cameron WI 54822

1-800-891-9435 productsupport@smithco.com

Introduction

Operation

Spraying Procedures Nozzle Charts Reference

CONTENTS

Introduction................................................................ 1-11

Introduction ................................................................. 1

Symbols................................................................... 2-3

Safety.......................................................................... 4

Safety Decal location .................................................. 5

General Safe Practices............................................... 6

Safe Spraying Practices ............................................. 7

Specifications.............................................................. 8

Optional Spray Equipment .......................................... 8

Set Up ......................................................................... 9

Controls & Instruments.........................................10-11

Operation ................................................................. 12-29

Operating Instructions.......................................... 12-14

SharpShooter - Rate Sync Console Features .......... 15

Raven 440 Console Features ................................... 16

Console Programming.............................................. 17

Console Calibration................................................... 18

Initial Programming .............................................. 19-24

Spray Operation ........................................................ 25

Re-Calibration of Flow Meter..................................... 26

Turf Management ...................................................... 27

Hose & Handgun Spraying ........................................ 27

Troubleshooting Nozzle Valves ............................ 28-29

Reference ..................................................................... 30

Collection Times ....................................................... 30

Blended Pulse Tip Selection Guide........................... 31

Declaration of Conformity ......................................

32-33

Quick Reference .................................................................34

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

INTRODUCTION

Read this manual and all other manuals pertaining to the Spray Star 3180 carefully as they contain safety, oper-

ating, assembly and maintenance instructions. Failure to do so could result in personal injury or equipment

damage.

Keep manuals in a safe place after operator and maintenance personnel have read them. Right and left sides are

from the operator’s seat, facing forward.

All

SmithcoSmithco

Smithco machines have a Serial Number and Model Number. Both numbers are needed when ordering

parts. The serial number plate on the Spray Star 3180 is located on top of the frame, between the hydro pump

and spray tank. Refer to engine manual for placement of engine serial number. Refer to engine manual for place-

ment of engine serial number.

For product and accessory information, help finding a dealer, or to register your procuct please contact us at

www.Smithco.com.

Information needed when ordering replacement parts:

1. Model Number of machine

2. Serial Number of machine

3. Name and Part Number of part

4. Quantity of parts

For easy access record your Serial and Model numbers here.

CALIFORNIA

Proposition 65 Warning

Engine exhaust and some of its constituents

are known to the State of California to

cause cancer, birth defects, and other

reproductive harm.

WARNING

lb/kg Empty

lb/kg Full

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SYMBOLS

Park Brake

Release

Hydraulic Oil

Level

Choke - OpenChoke - ClosedHand Throttle

Hour Meter Hour Meter Fuse

Glow PlugGlow Plug - OffGlow Plug - On

RPM Gasoline Diesel

Water

Temperature

Light

Engine Oil

Engine - Stop Engine - Start Engine - Run

No Electrical

Power

Electrical Power

Read Operator’s

Manual

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SYMBOLS

No Smoking Moving Parts

Manual

Operation

Pinch Point

Step Hot Surface

Hydraulic Fluid

Penetration

Lift Arm Tractor

Engage Disengage PTO

Ground Speed Fast Slow

High

Low

Forward

Reverse

Neutral

Warning

Danger

Caution

Up/RaiseDown/LowerUp/Down Arrow

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFETY

Read and understand this manual and all safety signs before operating and maintaining. Review the safety

instructions and precautions annually.

TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL

YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND THE SAFETY OF

OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.

SAFETY SIGNAL WORDS

Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The

appropriate signal word for each has been selected using the following guidelines:

DANGER: Red. Indicates an imminently hazardous situation

that, if not avoided, will result in death or serious injury. This

signal word is to be limited to the most extreme situations

typically for machine components which, for functional

purposes, cannot be guarded.

WARNING: Orange. Indicates a potentially hazardous

situation that, if not avoided, could result in death or serious

injury, and includes hazards that are exposed when guards

are removed. It may also be used to alert against unsafe

practices.

CAUTION: Yellow. Indicates a potentially hazardous situa-

tion that, if not avoided, may result in minor or moderate

injury. It may also be used to alert against unsafe practices.

IMPORTANT: Blue. Indicates procedures which should be

followed to avoid damage to the machine.

Safety Alert Symbol

This symbol with a warning statement means:

“Warning, be alert! Your safety is involved!”

Carefully read the message that follows.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFETY DECAL LOCATION

REMEMBER: If Safety Decals** have been damaged, removed, become illegible or parts

replaced without decals, new decals must be applied. New decals are available from

your authorized distributor.

This is a list of decals located on the Spray Star 3180. Part number, description and location will help in reorder-

ing a decals.

A 15-463 Decal Spray Pump

25-375 Decal, 94 dBA

B 25-277 Decal, Battery Warning

C 25-286 Decal, Pinch Point

D 25-298 Decal, Warning Hot

E 25-321 Decal, Diesel Fuel Only

F 20-545 Decal, Dash Panel

G 30-157 Decal, Control Panel

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFE PRACTICES

1. It is your responsibility to read this manual and all publications associated with this machine.

2. Never allow anyone to operate or service the machine or its optional equipment without proper training and

instructions. Never allow minors to operate any equipment.

3. Learn the proper use of the machine, the location and purpose of all the controls and gauges before you

operate the equipment. Working with unfamiliar equipment can lead to accidents.

4. Wear all the necessary protective clothing and personal safety devises to protect your head, eyes, ears,

hands and feet. Operate the machine only in daylight or in good artificial light.

5. Inspect the area where the equipment will be used. Pick up all debris you can find before operating.

Beware of overhead obstructions and underground obstacles. Stay alert for hidden hazards.

6. Never operate equipment that is not in perfect working order or without decals, guards, shields, or other

protective devices in place.

7. Never disconnect or bypass any switch.

8. Carbon monoxide in the exhaust fumes can be fatal when inhaled, never operate a machine without proper

ventilation.

9. Fuel is highly flammable, handle with care.

10. Keep engine clean. Allow the engine to cool before storing and always remove the ignition key.

11. Disengage all drives and set park brake before starting the engine.

12. Never use your hands to search for oil leaks. Hydraulic fluid under pressure can penetrate the skin and

cause serious injury.

13. This machine demands your attention. To prevent loss of control or tipping of the vehicle:

A. Use extra caution in backing up the vehicle. Ensure area is clear.

B. Do not stop or start suddenly on any slope.

C. Reduce speed on slopes and in sharp turns. Use caution when changing directions on slopes.

D. Stay alert for holes in the terrain and other hidden hazards.

14. Before leaving operator’s position:

A. Disengage all drives.

B. Set park brake.

C. Shut engine off and remove the ignition key.

D. If engine has to run to perform any maintenance keep hands, feet, clothing and all other parts of body

away from moving parts.

15. Keep hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,

adjust or service the machine.

16. Keep the area of operation clear of all bystanders.

17. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase.

18. Use parts and materials supplied by only. Do not modify any function or part.

19. Use caution when booms are down as they extend out beyond the center line of the machine.

20. The tank is a confined space, take precaution.

These machines are intended for professional maintenance on golf courses, sports turf, and any other

area maintained turf and related trails, paths and lots. No guaranty as to the suitability for any task is

expressed or implied.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFE SPRAYING PRACTICES

Persons engaged in the handling, preparation or application of chemicals must follow accepted practices to

insure the safety of themselves and others,

1. WEAR protective clothing including: gloves, hat, respirator, eye protection and skin covering suitable for

protection from chemicals being used.

2. BATHE thoroughly after any exposure to chemicals, giving particular attention to eyes, nose, ears and

mouth.

3. CLEAN equipment and materials in accordance with employer, municipal and state regulations. Use only

approved areas and drains.

4. DISPOSE of chemicals and rinse solutions by approved and legal means.

5. PROVIDE methods and materials for operators to wash eyes and hands immediately during the spraying

process.

6. PROVIDE methods and materials for control, safe dilution and neutralization of chemical spills during

preparation, spraying, transporting and cleanup.

7. Always check and follow the directions and safety warnings of the chemicals to be used.

8. Secure the discharge lines before starting the pump. An unsecured discharge line may whip.

9. Periodically inspect the pump and the system components.

10. Check hoses for weak or worn condition before each use. Make certain that all connections are tight and

secure.

11. Do not operate unit with leaks, frayed, kinked hoses or tubing. Repair or replace immediately.

12. Use only pipe, hose and fittings rated for maximum pressure or pressure at which pressure relief valve is

set at. When replacing pipe, hose or fittings, use new product.

13. Do not operate an engine in an enclosed area. Be sure the area is well ventilated.

14. Do not use these pumps for pumping water or other liquids for human or animal consumption.

15. Do not pump flammable or explosive fluids such as gasoline,

fuel oil, kerosene, etc. Do not use in explosive atmospheres. The

pump should be used only with liquids compatible with the pump

component materials.

16. Be sure all exposed moving parts are guarded and that all coupling devices are securely attached before

applying power.

17. Before servicing, disconnect all power, make sure all pressure in the system is relieved, drain all liquids

from the system and flush.

18. Protect pump from freezing conditions by draining liquid and pumping rust inhibiting antifreeze solution

through the system, coating the pump interior.

19. TRANSPORT - Machine must be stopped to raise or lower booms. Because of cam system, if booms

are raised in transit they can fall forward or backward when coming to a stop or while traveling on uneven

terrain.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SPECIFICATIONS

WEIGHTS AND DIMENSIONS

Length 128" (325 cm)

Width 72" (183 cm)

Height w/ ROPS 84" (213 cm)

Height w/ Booms Folded 136" (345 cm)

Wheel Base 68" (173 cm)

Weight Empty 2340 lbs (1061 kg)

Weight Full 4950 lbs (2245 kg)

SOUND LEVEL (DBA)

At ear level 88.4 dBA

At 30 ft. (9.14 m) 77 dBA

ENGINE

Make Kubota

Model# V1505

Type / Spec# 1G994-0000

Horsepower 35.5 hp (26.6 kW)

Fuel (EMISSIONS) No.1-D or No. 2-D, S500: Low Sulfur Diesel (LSD) less than 500 ppm or 0.05 wt.%

No1-D or No.2-D, S15: Ultra Low Sulfur Diesel (ULSD) less than 15 ppm or 0.0015 wt.%

Cooling System Liquid Cooled

Lubrication System Full Pressure

Alternator 15 Amp

WHEELS & TIRE Front: Two 20 x 11.00 x 10 Turf; 20 psi (1.4 bar)

Rear: Two 29 x 14.00 x 15 Multi-Trac; 30 psi (2.0 bar)

SPEED

Infinitely Variable 0-10 m.p.h. (0-18 kph)

BATTERY Automotive type 24F - 12 volt

BCI Group Size 24

Cold Cranking Amps 900 minimum

Ground Terminal Polarity Negative (-)

Maximum Length 10.25" (26 cm)

Maximum Width 6.88" (17 cm)

Maximum Height 10" (25 cm)

FLUID CAPACITY

Crankcase Oil See Engine Manual

Fuel 7 gallon (26.5 liters)

Hydraulic Fluid 10 gallon (37.8 liters)

Grade of Hydraulic Fluid SAE 10W-40 API Service SJ or higher Motor Oil

Radiator 1.06 gallons

OPTIONAL EQUIPMENT

15-618 Water Meter Kit 30-009 Manual Hose Reel

17-585 18' HD Super Boom 30-010 Electric Hose Reel

17-580 20' HD Super Boom 30-004 Foam Marker

30-006 Fresh Water Tank 15-835 Tank Rinse System

30-007 Chemical Cleanload Safe Fill 15-850 Sunshade Canopy

31-006 All Weather Top

17-590 Lazer-Beam Auto Boom for HD Booms

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SETUP

The Spray Star 3180 arrives from Smithco setup and ready for service. Depending on freight conditions battery

installed.

The spray system is normally shipped attached to the 3180 Prime Mover. If a spray system is to be fitted to a

Prime Mover by a dealer or factory, assemble and attach the components in accordance with the parts drawings

in the Spray Star 3180 Parts/Service Manual.

1. Check the tire pressure. The front tires are 20 psi (1.4 bar)

and rear tires are 30 psi (2.0 bar).

2. Battery is located under seat. This is a negative grounding

system.

Connecting battery cables to the

wrong post could result in personal

injury and/or damage to the electri-

cal system. Make sure battery and

cables do not interfere or rub on any moving part.

Connect red positive (+) cable (A) to battery first.

When disconnecting remove black negative (-)

cable (B) first.

3. Check hydraulic fluid level in tank located under the seat. Remove cap and add SAE 10W-40 API Service

SJ or higher motor oil if necessary. Fluid level should be about 2-2

" (5-6.4 cm) from the top of the tank

when cold. DO NOT OVERFILL.

4. Fill fuel tank, located on right side, with No. 2 diesel

Fuel is flammable, caution must be used when storing or handling it. Do not

fill fuel tank while engine is running or an enclosed area, fumes are explo-

sive and dangerous to inhale. DO NOT SMOKE while filling the fuel tank. DO

NOT OVERFILL

5. Machine should be greased before starting, refer to Spray Star 3180 Parts/Service Manual for location.

6. Attach the Spray Boom and any other Optional Equipment to the Prime Mover, in accordance with

instructions in the Spray Star 3180 Parts/Service Manual. The nozzles must be the correct distance above

the turf as described in Turf Spraying Guide. The spray boom must operate properly and the outer sec-

tions must break away safely if an object is struck by them, they must then return to normal operation

position.

7. Be sure to double check boom heights, nozzle spacing and displacement before spraying.

8. Machine is shipped with windshield washer fluid in to prevent freezing. Flush system completely with clear

water. Fill tank with water and retighten the four bolts used to hold the tank in place.

9. Read operating instructions before starting.

Never allow pump to run dry! The valve on the suction side of the pump

(between the pump and tank) must be fully open whenever the pump is

operated.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SETUP

FUEL

CHECK EMISSION REGULATIONS OF YOUR AREA

With Emission control now in effect diesel fuel specification type and sulfur content % (ppm) used must be in

compliant with all applicable emission regulations for the area in which the engine is operated.

Use of diesel fuel with sulfur content less than 0.10% (1000 ppm) is strongly recommended.

If high sulfur fuel is used, change oil and oil filters twice as often.

DO NOT USE Fuels that have sulfur content greater than 1.0% (10000 ppm).

Diesel fuels specified in EN 590 or ASTM D975 are recommended.

Since KUBOTA diesel engines of less than 56kW (75 hp) utilize EPA Tire 4 and Interim Tier 4 Standards, the use

of low sulfur fuel or ultra low sulfur fuel is mandatory for these engines, when operated in US EPA regulated ar-

eas. Therefore, use No.2-D S500 or S15 diesel fuel as a alternative toe No. 2-D for ambient temperatures below -

10°C (14° F).

TOWING

When it is necessary to move the Spray Star 3180 without the engine running, there are 2 things that need to be

done. First, the bypass valve built into hydrostatic pump must be "open" by turning it

turn to open. The valve

is located on the back side of the pump. An "open" valve allows fluid to pass through the wheels freely. When

normal driven operation is desired, valve should be "closed" by turning it clockwise. Failure to "close" the valve

with engine running means no power to wheels. Secondly, the hand brake needs to be manually released. The

hand brake is located under the engine. To manually release the brake you must loosen the locknut and screw

in the stem to the bottom. Tighten the lock nut and pump handle until hard.

MANUAL BRAKE HAND PUMP MANIFOLD

The hand brake is located under the engine. The hand brake is con-

nected to he seat switch and automatically engages when operator

gets up from the seat. So when machine is not being driven, the ma-

chine is locked down. If engine is not running or you are towing the

machine you will have to manually release the brake. To manually

release the brake you must loosen the locknut and screw in the

stem to the bottom. Tighten the lock nut and pump handle until hard.

Run machine at half-throttle minimum, prior to operating trac-

tion pedal. This will ensure proper brake release.

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS & INSTRUMENTS

A. Hour Meter - The hour meter indicates hours of machine operation. It operates only when the ignition

switch is on.

B. Glow Plug - When ignition is turned on, glow plug lights when ready to start.

C. Water Temperature Light - Temperature light will come on when the engine starts to overheat.

D. Ignition Switch - The ignition switch has three positions: Off - Run - Start.

E. Tilt Steering - Hold lever down and adjust steering wheel to desired position and release lever.

F. Oil Light - The oil light should come on when the ignition is on without the engine running and go out when

the engine is running. The oil light will light when the oil pressure is low. If oil light should come on, shut

engine off immediately and find the cause.

G. Speedometer - The Speedometer indicates ground speed of the vehicle in miles per hour and kilometers

per hour.

H. Lights - This rocker switch turns lights on by pushing on the top and off by pushing on the bottom.

I. Ground Speed (Cruise) Control - This rocker switch initiates cruise control by pushing on the top and

turning it off by pushing on the bottom. Works with ground Speed Control Foot switch.

J. Buzzer - The buzzer sounds if the pump is running dry.

K. Spray Pump - This rocker switch turns the spray pump on by pushing on the

top and off by pushing on the bottom.

L. Left Boom Switch - This rocker switch lifts and lowers the left boom.

M. Right Boom Switch - This rocker switch lifts and lowers the right boom.

N. Hand Throttle - The hand throttle is used to regulate engine speed.

O. Cup Holder - Holds standard cup.

P. Spray Boss Control - Engages and disengages speed boss. Forward is

engage and all the way back is disengage. When the lever is engaged it sets

a stop for the accelerator. The accelerator pedal must be used to maintain

this speed. To adjust speed use the knob on the end of the lever, counter

clockwise increases speed and clockwise decreases speed. Disengage the

lever and you will have full accelerator pedal range.

Q. Park Brake Toggle Switch - This toggle switch will engage park brake. Lift

toggle cover and move switch forward. DO NOT ENGAGE WHILE IN MO-

TION.

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS & INSTRUMENTS

R. Ground Speed (Cruise) Control Foot Switch - When rocker switch is turned on and desired speed is

obtained, push foot speed control switch to set cruise. (see below).

S. Master Boom Switch - located on the left floorboard is used to override the master switch on the com-

puter console of the spray systems. By pushing down it will turn on/off the booms.

For the 440 System

only the Master Switch on the computer must be off for the master boom control switch to work.

T. Accelerator Pedal - This pedal controls ground speed. Press pedal to increase speed. Varying the

amount of movement of the pedal will vary the ground speed.

U. Reverse Pedal - This pedal controls reverse. Press pedal to move machine in reverse.

GROUND SPEED CONTROL

The ground speed control does not work the

same as an automotive type cruise. The ground

speed control is located on the center floorboard

and is used to lock forward speed.

TO ENGAGE:

1. Flip rocker switch ‘On’ (green light).

2. Obtain desired speed with foot pedal.

3. Step on foot switch to lock speed.

4. Push foot switch again to disengage.

To avoid abrupt stop, place foot on

traction pedal before disengaging

speed control.

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

OPERATION

Before operating the Spray Star 3180, become familiar with all controls and functions. Also complete all mainte-

nance requirements and read all safety warnings. Knowing the Spray Star 3180 thoroughly, how it operates, and

by doing the prescribed maintenance steps, you can expect trouble free operation for years to come.

SAFETY

Operator needs to always be the concern of an operator of a moving vehicle or any machine with moving parts.

1. Keep all shields and guards in place.

2. Keep the parking brake engaged any time the operator is away from the vehicle or whenever service is

performed.

3. Always wear the necessary protective clothing and equipment.

4. Turn engine off when refueling or performing maintenance not specifically requiring engine power.

DAILY CHECKLIST

1. Check the engine oil level. Add as needed. DO NOT OVERFILL. Refer to engine owner's manual for oil

grade and procedure.

2. Tire pressure should be 20 psi (1.4 bar) on front and 30 psi (2.0 bar) on back.

3. Inspect the electrical system and battery cables for loose connections or frayed wiring. Replace any faulty

equipment or tighten if loose.

4. Check hardware for loose or missing nuts, bolts, screws, etc., and tighten or replace as needed.

5. Inspect hydraulic lines for damage or leaks. Never use hands to inspect for leaks.

6. Check the hydraulic fluid level. The hydraulic fluid tank is located under the seat. The fluid level should be

2"-2½" (5 - 6.4 cm) from the top of the tank when cold. Use only SAE 10W-40 API Service SJ or higher

Motor Oil.

7. Inspect the steering, throttle and shift linkages for good hookups and

clear travel.

8. Check controls for smooth, proper working operation. Lubricate as

needed.

9. Check anti-vibration mounts on engine frame.

STARTING THE ENGINE

1. Make sure both fuel flow valves are ‘On’. They are located on the fuel

tank.

2. The ignition switch is located on the dashboard. Insert the key (A) and

turn clockwise to (B). When glow plug light goes off Turn key to (C) un-

til the engine starts. Release the key and it will return to the run posi-

tion (B).

3. Allow engine to idle and warm up before selecting direction of travel.

STOPPING THE ENGINE

If the engine has been running under high power, let it run at slow idle speed

a few minutes to cool the engine down, before turning the ignition switch to

the OFF position.

1. Disengage spray pump.

2. Move the throttle lever to “slow” and turn ignition key to the “off” position.

3. Remove the ignition key and engage the park brake.

Never leave the vehicle unattended with the engine running. Always bring

the vehicle to a complete stop, engage park brake, turn key off and remove

key.

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

OPERATION

Run machine at half-throttle minimum, prior to operating traction pedal. This

will ensure proper brake release.

Before using the Spray Star, the operator and spray technician must familiarize themselves with all of the infor-

mation on chemical spraying contained in the Turf Spray Guide.

All testing and calibrating of sprayers is to be done with water, not chemicals. This insures the safety to all in-

volved in performing the calibration operation. Only after all calibration procedures are completed should chemi-

cal be added to the sprayer.

HILLSIDE OPERATION

Do NOT stop or start suddenly on any slope. Be especially cautious when changing direction. Do NOT operate

on slopes greater than 10°.

BATTERY

Batteries normally produce explosive gases which can cause personal injury. Do not allow flames, sparks or any

ignited object to come near the battery. When charging or working near battery, always shield your eyes and

always provide proper ventilation.

Battery cable should be disconnected before using “Fast Charge”.

Charge battery at 15 amps for 10 minutes or 7 amps for 30 minutes. Do not exceed the recommended charging

rate. If electrolyte starts boiling over, decrease charging.

Always remove grounded (-) battery clamp first and replace it last. Avoid hazards by:

1. Filling batteries in well-ventilated areas.

2. Wear eye protection and rubber gloves.

3. Avoid breathing fumes when electrolyte is added.

4. Avoid spilling or dripping electrolyte.

Battery Electrolyte is an acidic solution and should be handled with care. If

electrolyte is splashed on any part of your body, flush all contact areas imme-

diately with liberal amounts of water. Get medical attention immediately.

JUMP STARTING

Use of booster battery and jumper cables. Particular care should be used

when connecting a booster battery. Use proper polarity in order to prevent

sparks.

To jump start (negative grounded battery):

1. Shield eyes.

2. Connect ends of one cable to positive (+) terminals of

each battery, first (A) then (B).

3. Connect one end of other cable to negative (-) terminal

of "good" battery (C).

4. Connect other end of cable (D) to engine block on unit

being started (NOT to negative (-) terminal of battery)

To prevent damage to other electrical components on unit

being started, make certain that engine is at idle speed before

disconnecting jumper cables.

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

OPERATION (CONTINUED)

SPRAYER VALVE SETTINGS AND SPRAY TANK AGITATION

The 3-way valve on the suction side of the pump, between the tank and the pump must be open before pump is

engaged. Close this valve only when necessary to clean the filter with spray material in the spray tank.

There is one manual flow control valve on the discharge side of the spray system. This valve controls the agita-

tor. This valve may be opened as much as necessary to provide hydraulic agitation through the quadrajet agitator

in the tank bottom. This valve may be partially closed to prevent or reduce foam buildup from the spray materials

inside the tank. When the liquid level in the spray tank reaches a certain level (usually 1-25 gallons (3.8-95 Li-

ters) depending on terrain and other conditions) it may be necessary to close the valve in the agitator line in

order to prevent loss of suction prime.

If your Spray Star is fitted with a hose reel, there is a second ball valve on the discharge system to supply mate-

rial to the hose reel.

The Quadrajet agitation system operates with four venturi jets in the tank bottom. These jets have replaceable

orifice discs which discharge the following amounts of spay material.

Input to Input to Agitator Agitator Agitator Agitator

Nozzle Agitator Agitator Pressure Pressure Output Output

Diameter in gpm in L/min in psi in bar in gpm in L/min

/8" 1.9 7.2 25 1.7 6.3 23.8

/8" 2.7 10.2 50 3.4 10.0 37.9

/8" 3.8 14.4 100 6.9 15.0 56.8

/32" 2.8 10.6 25 1.7 7.6 28.8

/32" 4.2 15.9 50 3.4 12.2 46.2

/32" 5.5 20.8 100 6.9 17.5 66.2

/16" 3.6 13.6 25 1.7 9.1 34.4

/16" 5.6 21.2 50 33.4 14.3 54.1

/16" 7.9 29.9 100 6.9 18.7 70.8

You can change orifice disc sizes to enhance spray system performance. Smaller discs reduce amount of agita-

tion (desirable in some foaming materials) and make more dischargeable liquid available for nozzles. Larger (or

none) discs increase amount of agitation and make less dischargeable liquid available for nozzles.

ENVIZIO PRO II DO'S AND DON'TS

DO’S AND DON’TS

Do have the serial number and firmware revision available when calling for technical assistance. It is best if

the user is in the machine and in front of the field computer when calling for support.

Do review the manual in its entirety before operating the field computer.

Do turn machine on prior to starting Envizio Pro II. Voltage spikes can cause damage to computer.

Don't let water on or near Envizio Pro II Computer.

Don’t turn the field computer off without properly closing any open jobs and powering down the computer. If

the field computer loses power during a job, information within the job files may be lost and the associated

files may become corrupt.

Do power down Envizio prior to shutting off machine.

Don’t use sharp objects or harsh chemicals on the field computer touch screen as they may damage the

display. Console Features

Do remove Envizio Pro II during cold weather. Cold weather will cause the battery to drain.

Envizio Pro II comes with a Quick Reference Guide and an Installation & Operation Manual. Please read

these manuals before operation. Manuals can be downloaded off the internet at www.ravenprecision.com

and off the www.smithco.com website under Parts and Technical Information.

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SHARPSHOOTER WITH RATE SYNC FEATURES

To Begin a Job & Create a Spray Zone

Turn Sharpshooter w/RateSync On

Press Auto/Manual button to Auto

PSI is preset.

Use arrow buttons to increase/decrease

POWER

Auto/Manual

Button

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

DATA

RAVEN 440 CONSOLE FEATURES

This Console (PGM F) requires selection of US (acres); SI (hectares) or TU

(1,000 sq ft) area and SP1 (wheel drive, etc).

A. POWER - Turns Console power OFF or ON. Turning Console OFF does not affect the data stored in

the computer.

B. Select manual or fully automatic control. This can automatically control two rates.

C. Manual override control provides capability for spot spraying.

D. Booms can be controlled individually, or all at once with MASTER ON/OFF Switch

E. Displays operating rate of application and flashing Tip Fault.

F. Displays function and calibration data.

G. CE - Use like you do CE (clear entry) key on a calculator. This key is also used to select an area

base measurement of US (acres), SI (Hectares) or TU (1,000 sq ft).

H. ENTER - Used only to enter the data into the Console.

SEE QUICK REFERENCE PAGE FOR DATA THAT SHOULD BE ENTERED

Calibration Keys: (Top Row) Used to enter Function Keys: (Bottom Row) Used to display data.

data into console to calibrate the system.

BOOM 1 CAL Length of Boom 1 TOTAL AREA Total Area Sprayed

BOOM 2 CAL Length of Boom 2 FIELD AREA Field Area Sprayed

BOOM 3 CAL Length of Boom 3 FIELD VOLUME Volume Applied to Field

SPEED CAL Measured Off Drive Line DISTANCE Distance Traveled

METER CAL Flow Meter Calibration Number SPEED Speed of Vehicle

VALVE CAL Control Valve Response Time VOLUME/TANK Volume Remaining in Carrier Tank

RATE 1 CAL Target Application Rate TIME 24 hour clock (military time)

RATE 2 CAL Target Application Rate

SELF TEST Simulates Vehicle Speed

Operation

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

RAVEN 440 CONSOLE PROGRAMMING

When entering data into the Console computer, the entry sequence is always the same. Data must be entered

into the first eight keys.

1. Depress the key which you wish to enter data. 2. Depress the “Enter” key. An “E” will illuminate

in the DATA display.

3. Depress the keys corresponding to the 4. Complete the entry by again depressing the

number you wish to enter (i.e. “5”, “7”, “2”). “ENTER” key.

The numbers will be displayed in the DATA

display as they are entered.

RAVEN 440 CONSOLE CALIBRATION

CALCULATING “BOOM CAL” (BOOM 1, BOOM 2, BOOM 3)

Calculate the width of each boom in inches (centimeters) by multiplying the number of tips times the spacing.

Write these boom widths down for future reference when programming the Console computer. The Console is

capable of controlling up to three (3) booms.

CALCULATING “SPEED CAL"

1. Enter Speed Cal in key of 785 for GPS.

2. Place Master and Boom 1 switches to on.

3. Enter “0” in key .

4. Drive 1 mile. Do not use vehicle odometer to determine distance, use section lines or highway markers.

5. It should read a value of approximately 5280. If it reads between 5200-5350, the Speed Cal for this vehicle

is 688.

If the Distance display reads any other value, divide Speed Cal by the value observed in Distance, then

multiply by 5280. This will give you the correct value to enter for Speed Cal. You must round off to the

nearest 3 digit number (use 120 not 120.3).

Leht laadib ...

Smithco Spray Star 3187/3188 Rate-Sync Kasutusjuhend

Bränd: Smithco

Mudel: Spray Star 3187/3188 Rate-Sync

Tüüp: Kasutusjuhend

Laadige alla PDF

aruanne

teistes keeltes

English: Smithco Spray Star 3187/3188 Rate-Sync Operating instructions

Smithco Spray Star 3187/3188 Rate-Sync Kasutusjuhend

Smithco Spray Star 3187/3188 Rate-Sync Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid