SPRAY STAR 1110
1101 Manual System
1102 Radion 8140
1104 TeeJet 744
1105/1108 Star Command I
1115/1118 Star Command II
SN: 100742
Product Support: Hwy SS & Poplar Ave; Cameron WI 54822
1-800-891-9435 productsupport@smithco.com
Operator’s Manual
Introduction Operation Diagrams Spraying Procedures Reference
CONTENTS
Introduction ................................................................ 1-10
Introduction ................................................................. 1
Symbols ...................................................................... 2
Safety .......................................................................... 3
Safety Decals .............................................................. 4
General Safe Practices ............................................... 5
Safe Spraying Practices .............................................. 6
Specications ............................................................. 7
Optional Spray Equipment .......................................... 7
Set Up ......................................................................... 8
Controls & Instruments ........................................... 9-10
Operation .................................................................. 11-14
Operating Instructions ...........................................11-12
Tank Agitation ............................................................ 13
Sprayer Cleaning ................................................. 13-14
Diagrams ................................................................... 15-16
Wiring Diagram ......................................................... 15
Hydraulic Diagram ..................................................... 16
Reference .................................................................. 17-20
Declaration of Conformity ..................................... 17-18
Quick Reference ....................................................... 20
1
Introduction
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
INTRODUCTION
Thank you for purchasing a Smithco product.
Read this manual and all other manuals pertaining to the Spray Star 1110 carefully as they contain safety,
operating, assembly and maintenance instructions. Failure to do so could result in personal injury or equip-
ment damage.
Keep manuals in a safe place after operator and maintenance personnel have read them. Right and left sides
are from the operator’s seat, facing forward.
All Smithco machines have a Serial Number and Model Number. Both numbers are needed when ordering
parts. The serial number plate on the Spray Star 1110 is located on the right front bumper. Refer to engine
manual for placement of engine serial number. Refer to engine manual for placement of engine serial number.
For product and accessory information, help nding a dealer, or to register your product please contact us at
www.Smithco.com.
Information needed when ordering replacement parts:
1. Model Number of Machine 1. MODEL NUMBER OF MACHINE
2. Serial Number of machine
3. Name and Part Number of part
4. Quantity of parts
For easy access record your Serial and Model numbers here.
Model Number:
Serial Number:
Date of Purchase:
SMITHCO CUSTOMER SERVICE 1-800-891-9435
WARNING:
Engine exhaust and some of its constituents are
known to the State of California to cause cancer,
birth defects, and other reproductive harm.
For more information visit
www.P65Warning.ca.gov
WARNING
Failure to follow cautious operating practices can re-
sult in serious injury to the operator or other persons.
The owner must understand these instructions, and
must allow only trained persons who understand these
instructions to operate this vehicle.
2
Introduction
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
SYMBOLS
Read Operator’s
Manual
Engine Stop Engine Start Engine Run Engine Oil
Water
Temperature
RPM
Gasoline Diesel Glow Plug
Hour Meter Hand Throttle
Choke Hydraulic
Oil Level
Ground Speed
Park Brake Park Brake
Release
Fast Slow Lift Arm
Moving Parts Pinch Point Hot Surface Hydraulic Fluid
Penetration
No Riders
Rollover
Danger
Headlamp Blower Warning
Danger
Caution
Seat Belt
20° MAX
3
Introduction
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
SAFETY WARNINGS
Read and understand this manual and all safety signs before operating and maintaining. Review the safety
instructions and precautions annually.
TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL
YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND THE SAFETY OF
OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH
Safety Alert Symbol
This symbol with a warning statement means:
WARNING! BE ALERT!
YOUR SAFETY IS INVOLVED!
Carefully read the message that follows
SAFETY SIGNAL WORDS
Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The
appropriate signal word for each has been selected using the following guidelines:
DANGER: Red. Indicates an imminently hazardous situa-
tion that, if not avoided, will result in death or serious injury.
This signal word is to be limited to the most extreme situa-
tions typically for machine components which, for functional
purposes, cannot be guarded.
WARNING: Orange. Indicates a potentially hazardous
situation that, if not avoided, could result in death or serious
injury, and includes hazards that are exposed when guards
are removed. It may also be used to alert against unsafe
practices.
CAUTION: Yellow. Indicates a potentially hazardous situ-
ation that, if not avoided, may result in minor or moderate
injury. It may also be used to alert against unsafe practices.
IMPORTANT: Blue. Indicates procedures which should be
followed to avoid damage to the machine.
4
Introduction
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
SAFETY DECAL LOCATION
REMEMBER: If Safety Decals** have been damaged, removed, become illegible or parts
replaced without decals, new decals must be applied. New decals are available from your
authorized distributor or factory.
THIS IS A LIST OF DECALS LOCATED ON THE SPRAY STAR 1110. PART NUMBER, DESCRIPTION
AND LOCATION WILL HELP IN REORDERING A DECALS.
A 10-367 Decal, Spray Star 1110
B 25-356 Decal, Tire Pressure 20psi
C ** 25-352 Decal, Bypass Valve
D ** 25-298 Decal, Warning Hot
E ** 15-719 Decal, Speed Control
F** 27-093 Decal, Oil Level
G 25-370 Decal, 88 dba
H ** 15-463 Decal, Spray Pump
I 25-373 Decal, Smithco
J 10-657 Decal, Control Panel
K** 25-277 Decal, Battery Warning
L 14-803 Decal, Clean Agitation Strainer
** Safety Decals Required
5
Introduction
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
SAFE PRACTICES
1. It is your responsibility to read this manual and all publications associated with this machine.
2. Never allow anyone to operate or service the machine or its optional equipment without proper training
and instructions. Never allow minors to operate any equipment.
3. Learn the proper use of the machine, the location and purpose of all the controls and gages before you
operate the equipment. Working with unfamiliar equipment can lead to accidents.
4. Wear all the necessary protective clothing and personal safety devises to protect your head, eyes, ears,
hands and feet. Operate the machine only in daylight or in good articial light.
5. Inspect the area where the equipment will be used. Pick up all debris you can nd before operating.
Beware of overhead obstructions and underground obstacles. Stay alert for hidden hazards.
6. Never operate equipment that is not in perfect working order or without decals, guards, shields, or other
protective devices in place.
7. Never disconnect or bypass any switch.
8. Carbon monoxide in the exhaust fumes can be fatal when inhaled, never operate a machine without
proper ventilation.
9. Fuel is highly ammable, handle with care. When lling tank stop 1 inch(2.54 cm) from top. Leave room
for expansion. DO NOT OVERFILL.
10. Keep engine clean. Allow the engine to cool before storing and always remove the ignition key.
11. Disengage all drives and set park brake before starting the engine.
12. Never use your hands to search for oil leaks. Hydraulic uid under pressure can penetrate the skin and
cause serious injury.
13. This machine demands your attention. To prevent loss of control or tipping of the vehicle:
A. Use extra caution in backing up the vehicle. Ensure area is clear.
B. Do not stop or start suddenly on any slope.
C. Reduce speed on slopes and in sharp turns. Use caution when changing directions on slopes.
D. Stay alert for holes in the terrain and other hidden hazards.
14. Before leaving operator’s position:
A. Disengage all drives.
B. Set park brake.
C. Shut engine o and remove the ignition key.
D. If engine has to run to perform any maintenance keep hands, feet, clothing and all other parts of
body away from moving parts.
15. Keep hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,
adjust or service the machine.
16. Keep the area of operation clear of all bystanders.
17. Never carry passengers.
18. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase.
19. Use parts and materials supplied by Smithco only. Do not modify any function or part.
20. Use caution when booms are down as they extend out beyond the center line of the machine.
21. The spray tank is a conned space, take precaution.
These machines are intended for professional maintenance on golf courses, sports turf, and any other
area maintained turf and related trails, paths and lots. No guarantee as to the suitability for any task is
expressed or implied.
6
Introduction
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
SAFE SPRAYING PRACTICES
Persons engaged in the handling, preparation or application of chemicals must follow accepted practices to
insure the safety of themselves and others,
1. WEAR protective clothing including: gloves, hat, respirator, eye protection and skin covering suitable for
protection from chemicals being used.
2. BATHE thoroughly after any exposure to chemicals, giving particular attention to eyes, nose, ears and
mouth.
3. CLEAN equipment and materials in accordance with employer, municipal and state regulations. Use
only approved areas and drains.
4. DISPOSE of chemicals and rinse solutions by approved and legal means.
5. PROVIDE methods and materials for operators to wash eyes and hands immediately during the spray-
ing process.
6. PROVIDE methods and materials for control, safe dilution and neutralization of chemical spills during
preparation, spraying, transporting and cleanup.
7. Always check and follow the directions and safety warnings of the chemicals to be used.
8. Secure the discharge lines before starting the pump. An unsecured discharge line may whip.
9. Periodically inspect the pump and the system components.
10. Check hoses for weak or worn condition before each use. Make certain that all connections are tight
and secure.
11. Do not operate unit with leaks, frayed, kinked hoses or tubing. Repair or replace immediately.
12. Use only pipe, hose and ttings rated for maximum pressure or pressure at which pressure relief valve
is set at. When replacing pipe, hose or ttings, use new product.
13. Do not operate a gasoline engine in an enclosed area. Be sure the area is well ventilated.
14. Do not use these pumps for pumping water or other liquids for human or animal consumption.
15. Do not pump ammable or explosive uids such as gasoline, fuel
oil, kerosene, etc.
Do not use in explosive atmospheres. The pump should be used
only with liquids compatible with the pump component materials.
16. Be sure all exposed moving parts are guarded and that all coupling
devices are securely attached before applying power.
17. Before servicing, disconnect all power, make sure all pressure in the system is relieved, drain all liquids
from the system and ush.
18. Protect pump from freezing conditions by draining liquid and pumping rust inhibiting antifreeze solution
through the system, coating the pump interior.
19. TRANSPORT - Machine must be stopped to raise or lower booms. Because of cam system, if booms
are raised in transit they can fall forward or backward when coming to a stop or while traveling on un-
even terrain.
20. If using Simulated Speed with a Radion 8140, one needs to change back to
Ground Speed for proper rate control when spraying.
7
Introduction
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
SPECIFICATIONS
WEIGHTS AND DIMENSIONS
Length 112" (285 cm)
Width 70" (178 cm)
Width With Boom Open 180" (457 m)
Height 75" (191 cm)
Wheel Base 53" (135 cm)
Weight Empty 1480lbs (675 kg)
Weight Full 2248 lbs (1025 kg)
SOUND LEVEL (DBA)
At ear level 85 dba
At 3 ft (0.914 m) 83 dba
At 30 ft (9.14 m) 72 dba
ENGINE
Make Briggs & Stratton
Model# 386447
Type / Spec# 0459 G1
Horsepower 23HP (17 kw)
Fuel Unleaded 87 Octane Gasoline Minimum
Cooling System Air Cooled
Lubrication System Full Pressure
Alternator 25 Amp
WHEELS & TIRE Front: Two 20 x 10.00 x 10 NHS Smooth; 20psi (1.4 bar)
Rear: Two 24 x 13.00 x 12 NHS Multi-Trac; 20 psi (1.4 bar)
PARK BRAKE Hand Operated Lever, Discs on Rear Axle 0 to 3 mph (0-4.8 kph)
SPEED
Forward Speed 0-8 mph (0-12.8 kph)
Reverse Speed 0-3 mph (0-4.8 kph)
BATTERY Automotive type 24F-12 Volt
BCI Group Size 24
Cold Cranking Amps 575 minimum
Ground Terminal Polarity Negative (-)
Maximum Length 10.25" (26 cm)
Maximum Width 6.88" (17 cm)
Maximum Height 10" (25 cm)
FLUID CAPACITY
Crankcase Oil See Engine Manual
Fuel 6 gallon (22.7 liters)
Hydraulic Fluid 5 gallon (19 liters)
Grade of Hydraulic Fluid SAE 10W-40 API Service SJ or higher Motor Oil
OPTIONAL EQUIPMENT
10-417 Chemical Clean-load Safe Fill System 17-601 15' Heavy Duty Boom
10-734 16 Gal. Wash System 17-585 18' Heavy Duty Boom
10-653 Fresh Water Tank - Front Mount 1102 TeeJet 744 Spray System
30-006 Fresh Water Tank - Rear mount 1104 Radion 8140 Spray System
15-835 Tank Rinsing System 1101 3-Way Manual System
10-370 Water Meter Kit (liters) 1105/1108 DynaJet/Radion Spray System
10-365 Water Meter Kit (gallons) 1115/1118 DynaJet/Aeros Spray System
10-740 Foam Marker 15-622 Canopy
10-422 Hose Reel Mount Kit
16-129 Manual Rewind Hose Reel, 200-foot/61-meter capacity
16-906 Electric Rewind Hose Reel, 200-foot/61-meter capacity
8
Introduction
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
SETUP
The Spray Star 1110 arrives from Smithco setup and ready for service. Depending on freight conditions the
battery may have to be installed.
The spray system is normally shipped attached to the Prime Mover. If a spray system is to be tted to a Prime
Mover by a dealer or end user, assemble and attach the components in accordance with the parts drawings in
the Spray Star 1110 Parts/Service Manual.
1. Check the tire pressure. The front are 20 psi (1.4 bar) and rear tires are 18 psi (1.3 bar).
2. Battery is located behind the right front wheel.
Connecting battery cables to the wrong
post could result in personal injury and/or
damage to the electrical system. Make sure
battery and cables do not interfere or rub on
any moving part. Connect red positive (+) cable (A) to battery
rst. When disconnecting remove black negative (-) cable (B)
rst.
3. Check hydraulic uid level in tank located on the left side of the
seat. Remove cap and add SAE 10W-40 API Service SJ or higher
motor oil if necessary. Fluid level should be about 2-21/2" (5-6.4 cm)
from the top of the tank when cold. DO NOT OVERFILL.
4. Fill fuel tank, located on the right side, with Unleaded 87 Octane
gasoline (minimum). When lling the fuel tank stop when the fuel
reaches 1 inch (2.54cm) from the top. This space is necessary for
fuel expansion. DO NOT OVERFILL.
Fuel is ammable, caution must be used when storing or handling it.
Do not ll fuel tank while engine is running or an enclosed
area, fumes are explosive and dangerous to inhale. DO NOT SMOKE while
lling the fuel tank. DO NOT OVERFILL.
5. Machine should be greased before starting, refer to Spray Star 1110
Parts/Service Manual for location.
6. Attach the Spray Boom and any other Optional Equipment to the Prime Mover, in accordance with in-
structions in the Spray Star 1110 Parts/Service Manual. The nozzles must be the correct distance above
the turf as described in Turf Spraying Guide. The spray boom must operate properly and the outer sec-
tions must break away safely if an object is struck by them, they must then return to normal operation
position.
7. Be sure to double check boom heights, nozzle spacing and displacement before spraying.
8. Machine is shipped with windshield washer uid in Spray System to prevent freezing. Flush system
completely with clear water. Fill tank with water and re-tighten the four bolts used to hold the tank in
place.
9. Read operating instructions before starting.
Never allow pump to run dry! The valve on the suction side of the pump (between the pump and tank)
must be fully open whenever the pump is operated.
9
Introduction
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
CONTROLS & INSTRUMENTS
A. Hour Meter - The hour meter indicates hours of ma-
chine operation. It operates only when the ignition
switch is on.
B. GPS Speedometer - The Speedometer indicates
ground speed of the vehicle in miles per hour.
C. Oil Light - The oil light should come on when the ignition is on without the engine running and go out
when the engine is running. The oil light will light when the oil pressure is low. If oil light should come
on, shut engine o immediately and nd the cause.
D. Ignition Switch - The ignition switch has three positions: O - Run - Start.
E. Buzzer - The buzzer sounds if the pump is running dry.
F. Lights - This rocker switch turns lights on by pushing on the top and o by pushing on the bottom.
G. Spray Pump - This rocker switch turns the spray pump on by pushing on the top and o by pushing on
the bottom.
H. Left Boom Switch - This rocker switch lifts and lowers the left boom.
I. Right Boom Switch - This rocker switch lifts and lowers the right boom.
J. Dual USB Charging Port - lets you charge your cell phone, tablet, or other device.
K. Hand Throttle - The hand throttle is used to regulate engine speed.
L. GNSS Antenna Switch - (Optional) Used to turn on/o GNSS Antenna, used with spray systems.
SPEEDOMETER
This machine is equipped with a GPS Speedometer. Please note that if the speedometer has been powered
o longer than 4 hours, it could take up to 1 minute to acquire signal due to the satellites moving signicantly
from your location. This is normal. The current draw is extremely low and will have virtually zero impact on
a battery's charge. Hot start wire should be connected directly to battery +12volts and should remain pow-
ered 100% of the time. When GPS gauge rst receives power, the needle will sweep full counter clockwise
towards
0 mph. Pointer will stay at 0 mph and oscillate slightly at zero to indicate the GPS is acquiring satellites. GPS
is not yet functional to indicate speed. Once satellites are acquired (15-45 seconds), the pointer will swing
full scale and then back toward 0 mph to indicate it is now ready for operation.
10
Introduction
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
CONTROLS & INSTRUMENTS
M. Choke - The choke is used in starting the engine. Pull choke out to close
choke plate when starting a cold engine. Push in when engine starts. A
warm engine may not require "choking" to start.
N. Spray Boss Control - Engages and disengages speed boss. Forward is
engage and all the way back is disengage. When the lever is engaged
it sets a stop for the accelerator. The accelerator pedal must be used to
maintain this speed. To adjust speed use the knob on the end of the le-
ver, counter clockwise increases speed and clockwise decreases speed.
Disengage the lever and you will have full accelerator pedal range.
O. Park Brake - The park brake is only a parking brake. Pull back to re-
lease, push forward to apply. Some adjustment can be made by turning
the knob clockwise to tighten and counter clockwise to loosen.
P. Reverse Pedal - This pedal controls ground speed in the reverse direc-
tion. Press the pedal to reverse direction. Varying the amount of move-
ment of the pedal will vary the ground speed.
Q. Accelerator Pedal - This pedal controls ground speed. Press pedal to
increase speed. Varying the amount of movement of the pedal will vary the
ground speed.
MASTER BOOM SWITCH
The master boom switch (R), if required, is located on the left
oorboard. It is used to override the master switch on the com-
puter console of the Radion Spray Systems. By pushing down
it will turn on/o the booms. For TeeJet Systems, the master
switch on the computer must be on.
11
Operation
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
OPERATION
Before operating the Spray Star 1110, become familiar with all controls and functions. Also complete all main-
tenance requirements and read all safety warnings. Knowing the Spray Star 1110 thoroughly, how it operates,
and by doing the prescribed maintenance steps, you can expect trouble free operation for years to come.
SAFETY
Safety needs to always be the concern of an operator of a moving vehicle or any machine with moving parts.
1. Keep all shields and guards in place.
2. Keep the parking brake engaged any time the operator is away from the vehicle or whenever service is
performed.
3. Always wear the necessary protective clothing and equipment.
4. Turn engine o when refueling or performing maintenance not specically requiring engine power.
DAILY CHECKLIST
1. Check the engine oil level. Add as needed. DO NOT OVERFILL. Refer to engine owner's manual for oil
grade and procedure.
2. Tire pressure should be 20 psi (1.4 bar) maximum.
3. Inspect the electrical system and battery cables for loose connections or frayed wiring. Replace any
faulty equipment or tighten if loose.
4. Check hardware for loose or missing nuts, bolts, screws, etc., and tighten or replace as needed.
5. Inspect hydraulic lines for damage or leaks. Never use hands to inspect for leaks.
6. Check the hydraulic uid level. The hydraulic uid tank is located on the left side of the seat. The uid
level should be 2"-2½" (5 - 6.4 cm) from the top of the tank when cold. Use only SAE 10W-40 API Ser-
vice SJ or higher Motor Oil.
7. Inspect the steering, throttle and shift linkages for good hookups and
clear travel.
8. Check controls for smooth, proper working operation. Lubricate as
needed.
9. Check park brake adjustments. Adjust as required.
10. Check anti-vibration mounts on engine frame.
STARTING THE ENGINE
1. The ignition switch is located on the dashboard. Insert the key (A)
and turn clockwise until the engine starts (C). Release the key and it
will return to the run position (B). Use the choke and hand throttle as
necessary.
2. Allow engine to idle and warm up before selecting direction of travel.
STOPPING THE ENGINE
If the engine has been running under high power, let it run at slow idle speed a
few minutes to cool the engine down, before turning the ignition switch to the
OFF position.
1. Disengage spray pump.
2. Move the throttle lever to “slow” and turn ignition key to the “o” position.
3. Remove the ignition key and engage the park brake.
Never leave the vehicle unattended with the engine running. Always bring the
vehicle to a complete stop, engage park brake, turn key o and remove key.
12
Operation
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
OPERATION (CONTINUED)
Before using the Spray Star, the operator and spray technician must familiarize themselves with all of the information on
chemical spraying contained in the Turf Spray Guide.
All testing and calibrating of sprayers is to be done with water, not chemicals. This
insures the safety to all involved in performing the calibration operation. Only after all
calibration procedures are completed should chemical be added to the sprayer.
TOWING UNIT
When it is necessary to move the Spray Star 1110 without the engine running, the bypass valve built into hydrostatic pump
must be "open" by turning it counterclockwise. The valve is located on the bottom of the pump. An "open" valve allows
uid to pass through the wheels freely. When normal driven operation is desired, valve should be "closed" by turning it
clockwise. Failure to "close" the valve with engine running means no power to wheels.
HILLSIDE OPERATION
Do NOT stop or start suddenly on any slope. Be especially cautious when changing direction. Do NOT operate on slopes
greater than 20°.
BATTERY
Batteries normally produce explosive gases which can cause personal injury. Do not allow ames, sparks or any ignited
object to come near the battery. When charging or working near battery, always shield your eyes and always provide
proper ventilation.
Battery cable should be disconnected before using “Fast Charge”.
Charge battery at 15 amps for 10 minutes or 7 amps for 30 minutes. Do not exceed the recommended charging rate. If
electrolyte starts boiling over, decrease charging.
Always remove grounded (-) battery clamp rst and replace it last. Avoid hazards by:
1. Filling batteries in well-ventilated areas.
2. Wear eye protection and rubber gloves.
3. Avoid breathing fumes when electrolyte is added.
4. Avoid spilling or dripping electrolyte.
Battery Electrolyte is an acidic solution and should be handled with care. If electrolyte
is splashed on any part of your body, ush all contact areas immediately with liberal
amounts of water. Get medical attention immediately.
JUMP STARTING
Use of booster battery and jumper cables. Particular care should be used when con-
necting a booster battery. Use proper polarity in order to prevent sparks.
To jump start (negative grounded battery):
1. Shield eyes.
2. Connect ends of one cable to positive (+) terminals of each
battery, rst (A) then (B).
3. Connect one end of other cable to negative (-) terminal of
"good" battery (C).
4. Connect other end of cable (D) to engine block on unit being
started (NOT to negative (-) terminal of battery)
To prevent damage to other electrical components on unit being
started, make certain that engine is at idle speed before disconnect-
ing jumper cables.
13
Operation
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
TANK AGITATION
SPRAYER VALVE SETTINGS AND SPRAY TANK AGITATION
The 3-way valve on the suction side of the pump, between the tank and the pump must be open before pump
is engaged. Close this valve only when necessary to clean the lter with spray material in the spray tank.
There is one manual ow control valve on the discharge side of the spray system. This valve controls the
agitator. This valve may be opened as much as necessary to provide hydraulic agitation through the quadra-
jet agitator in the tank bottom. This valve may be partially closed to prevent or reduce foam buildup from the
spray materials inside the tank. When the liquid level in the spray tank reaches a certain level (usually 1-25
gallons (3.8-95 Liters) depending on terrain and other conditions) it may be necessary to close the valve in
the agitator line in order to prevent loss of suction prime.
If your Spray Star is tted with a hose reel, there is a second ball valve on the discharge system to supply ma-
terial to the hose reel.
The Quadrajet agitation system operates with four venturi jets in the tank bottom. These jets have replaceable
orice discs which discharge the following amounts of spay material.
Input to Input to Agitator Agitator Agitator Agitator
Nozzle Agitator Agitator Pressure Pressure Output Output
Diameter in gpm in L/min in psi in bar in gpm in L/min
1/8" 1.9 7.2 25 1.7 6.3 23.8
1/8" 2.7 10.2 50 3.4 10.0 37.9
1/8" 3.8 14.4 100 6.9 15.0 56.8
5/32" 2.8 10.6 25 1.7 7.6 28.8
5/32" 4.2 15.9 50 3.4 12.2 46.2
5/32" 5.5 20.8 100 6.9 17.5 66.2
3/16" 3.6 13.6 25 1.7 9.1 34.4
3/16" 5.6 21.2 50 33.4 14.3 54.1
3/16" 7.9 29.9 100 6.9 18.7 70.8
You can change orice disc sizes to enhance spray system performance. Smaller discs reduce amount of agi-
tation (desirable in some foaming materials) and make more discharged liquid available for nozzles. Larger (or
none) discs increase amount of agitation and make less discharged liquid available for nozzles.
SPRAYER CLEANING
DYNAJET® NOZZLE CLEANING
The Nozzle Coil Assembly will need to be taken apart and cleaned on a regular basis. To take apart and clean
you will need to use two wrenches provided with the DynaJet® System. Loosen the Nozzle assembly by plac-
ing a wrench on the tube assembly and one on the stainless cap. Hold one in place and turn the other wrench
to loosen assembly. Once apart, clean with water and
check for deteriorating parts. Replace parts as needed
by ordering the Spare Parts Kit 20-673-01P.
14
Operation
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
SPRAYER CLEANING
One of the most common causes for faulty-pump performance is corrosion inside the pump. Flush the pump and
entire system with a solution that will chemically neutralize the liquid pumped. Mix according to manufacturer’s
directions. This will dissolve most residue remaining in the pump, leaving the inside of the pump clean for the next
use.
TO PREVENT CORROSION
After cleaning the pump as directed, ush it with a permanent type automobile antifreeze (Prestone, Zerex, etc.)
containing a rust inhibitor. Use a 50% solution that is, half antifreeze and half water. Then coat the interior of the
pump with a substance which will prevent corrosion such as Fluid Film or WD40. If unit will not be used for an ex-
tended period of time, disconnect hoses into and out of the pump, seal openings to the pump with caps or tape.
Dispose of uids according to all federal, state and local regulations.
All chemicals and chemical residue must be removed after each use. Dispose
of uids and residue according to all federal, state and local regulations.
SPRAYER CLEANING
Empty tank and clean unit thoroughly after each use following these instructions:
1. Turn o 3-way valve and rinse inside of tank thoroughly with clean water, remove cap from valve to drain.
2. Fill tank ten percent full with clean water, Turn 3-way valve on and start pump and discharge water through
spray hose or spray boom (with nozzles removed), until empty.
3. Turn o 3-way valve again and rinse tank interior thoroughly. Remove cap from 3-way valve to drain.
4. Rinse exterior of sprayer thoroughly with clean water.
5. This sprayer is equipped with a self cleaning strainer. The strainer uses the excess pump ow to bypass clog-
ging particles back to the spray tank. There is a gap between the tapered inner cylinder and the screen face
that causes the inlet uid to ow at a high velocity past the screen face providing a continuous wash down of
particles. For this wash down to occur a minimum of +GPM/23 l/min is required through the bypass line.
AGITATION LINE STRAINER CLEANING
Agitation line strainer is located below the sprayer
lter. This strainer catches impurities that go to the
turbo-jet agitation system in the spray tank. It has a
quick disconnect pin on it to remove the bowl. After
EVERY use, remove bowl and clean screen. Re-
place screen as needed. We recommend a 50 Mesh
screen.
MANUAL HOSE REEL
Located at the back of the Spray Star on top of the
tank. Open the ball valve located near the manifold
valve to allow uid to ow into the hose reel. Place
the lockout pin in the unlocked position by pulling
and turning it half a turn, this will allow you to pull
out additional hose or to use the handle and wind up
the hose. To prevent movement during transport or
storage place the lockout pin in the locked position.
ELECTRIC HOSE REEL
Located at the back of the Spray Star on top of the tank. Open the ball valve located near the manifold valve to
allow uid to ow into the hose reel. To unwind hose just pull on the hose to get the desired amount. To wind up
the hose make sure the toggle switch is in the ON position, push the momentary push button switch until you have
reeled in the amount of hose desire. Turn o the safety switch when not in use.
FOAM MARKER
Located to the right of the control panel. Use lever on compressor to designate which boom is to be used to dis-
pense foam. Use dial located on the foamer to adjust pressure for the amount of foam that will be dispensed.
Switch on compressor also turns foamer on or o.
15
Schematics
WIRING DIAGRAM
Color Code Chart
Bl Blue
Br Brown
Y Yellow
G Green
O Orange
16
Schematics
HYDRAULIC DIAGRAM
17
Reference
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
Business name and full address of the manufacturer ▪ Търговско име и пълен адрес на производителя ▪ Obchodní jméno a plná adresa
výrobce ▪ Producentens firmanavn og fulde adresse ▪ Bedrijfsnaam en volledig adres van de fabrikant ▪ Tootja ärinimi ja täielik aadress ▪
Valmistajan toiminimi ja täydellinen osoite ▪ Nom commercial et adresse complète du fabricant ▪ Firmenname und vollständige Adresse des
Herstellers ▪ Επωνυμία και ταχυδρομική διεύθυνση κατασκευαστή ▪ A gyártó üzleti neve és teljes címe ▪ Ragione sociale e indirizzo
completo del fabbricante ▪ Uzņēmuma nosaukums un pilna ražotāja adrese ▪ Verslo pavadinimas ir pilnas gamintojo adresas ▪ Isem
kummerċjali u indirizz sħiħ tal-fabbrikant ▪ Nazwa firmy i pełny adres producenta ▪ Nome da empresa e endereço completo do fabricante ▪
Denumirea comercială şi adresa completă a producătorului ▪ Obchodný názov a úplná adresa výrobcu ▪ Naziv podjetja in polni naslov
proizvajalca ▪ Nombre de la empresa y dirección completa del fabricante ▪ Tillverkarens företagsnamn och kompletta adress
Smithco Inc.
34 West Avenue
Wayne, PA USA
19087-3311
Product Code ▪ Код на продукта ▪ Kód výrobku ▪ Produktkode ▪ Productcode ▪ Toote kood ▪ Tuotekoodi ▪ Code produit ▪ Produktcode ▪
Κωδικός προϊόντος ▪ Termékkód ▪ Codice prodotto ▪ Produkta kods ▪ Produkto kodas ▪ Kodiċi tal-Prodott ▪ Kod produktu ▪ Código do Produto
▪ Cod produs ▪ Kód výrobku ▪ Oznaka proizvoda ▪ Código de producto ▪ Produktkod
10-100
Machine Name ▪ Наименование на машината ▪ Název stroje ▪ Maskinnavn ▪ Machinenaam ▪ Masina nimi ▪ Laitteen nimi ▪ Nom de la
machine ▪ Maschinenbezeichnung ▪ Ονομασία μηχανήματος ▪ Gépnév ▪ Denominazione della macchina ▪ Iekārtas nosaukums ▪ Mašinos
pavadinimas ▪ Isem tal-Magna ▪ Nazwa urządzenia ▪ Nome da Máquina ▪ Numele echipamentului ▪ Názov stroja ▪ Naziv stroja ▪ Nombre de
la máquina ▪ Maskinens namn
Spray Star 1110
Designation ▪ Предназначение ▪ Označení ▪ Betegnelse ▪ Benaming ▪ Nimetus ▪ Tyyppimerkintä ▪ Pažymėjimas ▪ Bezeichnung ▪
Χαρακτηρισμός ▪ Megnevezés ▪ Funzione ▪ Apzīmējums ▪ Lithuanian ▪ Denominazzjoni ▪ Oznaczenie ▪ Designação ▪ Specificaţie ▪ Označenie
▪ Namen stroja ▪ Descripción ▪ Beteckning
Turf Sprayer
Serial Number ▪ Сериен номер ▪ Sériové číslo ▪ Serienummer ▪ Serienummer ▪ Seerianumber ▪ Valmistusnumero ▪ Numéro de série ▪
Seriennummer ▪ Σειριακός αριθμός ▪ Sorozatszám ▪ Numero di serie ▪ Sērijas numurs ▪ Serijos numeris ▪ Numru Serjali ▪ Numer seryjny ▪
Número de Série ▪ Număr de serie ▪ Sériové číslo ▪ Serijska številka ▪ Número de serie ▪ Serienummer
100684-100999
Engine ▪ Двигател ▪ Motor ▪ Motor ▪ Motor ▪ Mootor ▪ Moottori ▪ Moteur ▪ Motor ▪ Μηχανή ▪ Modulnév ▪ Motore ▪ Dzinējs ▪ Variklis ▪ Saħħa
Netta Installata ▪ Silnik ▪ Motor ▪ Motor ▪ Motor ▪ Motor ▪ Motor ▪ Motor
Briggs & Stratton 23 HP 386447
Net Installed Power ▪ Нетна инсталирана мощност ▪ Čistý instalovaný výkon ▪ Installeret nettoeffekt ▪ Netto geïnstalleerd vermogen ▪
Installeeritud netovõimsus ▪ Asennettu nettoteho ▪ Puissance nominale nette ▪ Installierte Nettoleistung ▪ Καθαρή εγκατεστημένη ισχύς ▪
Nettó beépített teljesítmény ▪ Potenza netta installata ▪ Paredzētā tīkla jauda ▪ Grynoji galia ▪ Wisa’ tal-Qtugħ ▪ Moc zainstalowana netto ▪
Potência instalada ▪ Puterea instalată netă ▪ Čistý inštalovaný výkon ▪ Neto vgrajena moč ▪ Potencia instalada neta ▪ Nettoeffekt
17 kW
Conforms to Directives ▪ В съответствие с директивите ▪ Splňuje podmínky směrnic ▪ Er i overensstemmelse med direktiver ▪ Voldoet aan
de richtlijnen ▪ Vastab direktiividele ▪ Direktiivien mukainen ▪ Conforme aux directives ▪ Entspricht Richtlinien ▪ Ακολουθήστε πιστά τις
Οδηγίες ▪ Megfelel az irányelveknek ▪ Conforme alle Direttive ▪ Atbilst direktīvām ▪ Atitinka direktyvų reikalavimus ▪ Valutazzjoni tal-
Konformità ▪ Dyrektywy związane ▪ Cumpre as Directivas ▪ Respectă Directivele ▪ Je v súlade so smernicami ▪ Skladnost z direktivami ▪
Cumple con las Directivas ▪ Uppfyller direktiv
2006/42/EC;
2000/14/EC Annex VI . Part 1
Conformity Assessment ▪ Оценка за съответствие ▪ Hodnocení plnění podmínek ▪ Overensstemmelsesvurdering ▪
Conformiteitsbeoordeling ▪ Vastavushindamine ▪ Vaatimustenmukaisuuden arviointi ▪ Evaluation de conformité ▪ Konformitätsbeurteilung ▪
Διαπίστωση Συμμόρφωσης ▪ Megfelelőség-értékelés ▪ Valutazione della conformità ▪ Atbilstības novērtējums ▪ Atitikties įvertinimas ▪ Livell
tal-Qawwa tal-Ħoss Imkejjel ▪ Ocena zgodności ▪ Avaliação de Conformidade ▪ Evaluarea conformităţii ▪ Vyhodnotenie zhodnosti ▪ Ocena
skladnosti ▪ Evaluación de conformidad ▪ Bedömning av överensstämmelse
2006/42/EC Annex VIII
Measured Sound Power Level ▪ Измерено ниво на звукова мощност ▪ Naměřený akustický výkon ▪ Målte lydstyrkeniveau ▪ Gemeten
geluidsniveau ▪ Mõõdetud helivõimsuse tase ▪ Mitattu äänitehotaso ▪ Niveau de puissance sonore mesuré ▪ Gemessener Schalldruckpegel ▪
Σταθμισμένο επίπεδο ηχητικής ισχύος ▪ Mért hangteljesítményszint ▪ Livello di potenza sonora misurato ▪ Izmērītais skaņas jaudas līmenis ▪
Išmatuotas garso stiprumo lygis ▪ Livell tal-Qawwa tal-Ħoss Iggarantit ▪ Moc akustyczna mierzona ▪ Nível sonoro medido ▪ Nivelul măsurat al
puterii acustice ▪ Nameraná hladina akustického výkonu ▪ Izmerjena raven zvočne moči ▪ Nivel de potencia sonora medido ▪ Uppmätt
ljudeffektsnivå
85dB(A)Lwa
Guaranteed Sound Power Level ▪ Гарантирано ниво на звукова мощност ▪ Garantovaný akustický výkon ▪ Garanteret lydstyrkeniveau ▪
Gegarandeerd geluidsniveau ▪ Garanteeritud helivõimsuse tase ▪ Taattu äänitehotaso ▪ Niveau de puissance sonore garanti ▪ Garantierter
Schalldruckpegel ▪ Εγγυημένο επίπεδο ηχητικής ισχύος ▪ Szavatolt hangteljesítményszint ▪ Livello di potenza sonora garantito ▪ Garantētais
skaņas jaudas līmenis ▪ Garantuotas garso stiprumo lygis ▪ Livell tal-Qawwa tal-Ħoss Iggarantit ▪ Moc akustyczna gwarantowana ▪ Nível
sonoro farantido ▪ Nivelul garantat al puterii acustice ▪ Garantovaná hladina akustického výkonu ▪ Zajamčena raven zvočne moči ▪ Nivel de
potencia sonora garantizado ▪ Garanterad ljudeffektsnivå
88 dB(A)Lwa
Conformity Assessment Procedure (Noise) ▪ Оценка за съответствие на процедурата (Шум) ▪ Postup hodnocení plnění podmínek (hluk) ▪
Procedure for overensstemmelsesvurdering (Støj) ▪ Procedure van de conformiteitsbeoordeling (geluid) ▪ Vastavushindamismenetlus (müra)
▪ Vaatimustenmukaisuuden arviointimenettely (Melu) ▪ Procédure d’évaluation de conformité (bruit) ▪ Konformitätsbeurteilungsverfahren
(Geräusch) ▪ Διαδικασία Αξιολόγησης Συμμόρφωσης (Θόρυβος) ▪ Megfelelőség-értékelési eljárás (Zaj) ▪ Procedura di valutazione della
conformità (rumore) ▪ Atbilstības novērtējuma procedūra (troksnis) ▪ Atitikties įvertinimo procedūra (garsas) ▪ Proċedura tal-Valutazzjoni tal-
Konformità (Ħoss) ▪ Procedura oceny zgodności (poziom hałasu) ▪ Processo de avaliação de conformidade (nível sonoro) Procedura de
evaluare a conformităţii (zgomot) ▪ Postup vyhodnocovania zhodnosti (hluk) ▪ Postopek za ugotavljanje skladnosti (hrup) ▪ Procedimiento de
evaluación de conformidad (ruido) ▪ Procedur för bedömning av överensstämmelse (buller)
2000/14/EC Annex VI Part 1
UK Notified Body for 2000/14/EC ▪ Нотифициран орган в Обединеното кралство за 2000/14/ЕО ▪ Úřad certifikovaný podle směrnice č.
2000/14/EC ▪ Det britiske bemyndigede organ for 2001/14/EF ▪ Engels adviesorgaan voor 2000/14/EG ▪ Ühendkuningriigi teavitatud asutus
direktiivi 2000/14/EÜ mõistes ▪ Direktiivin 2000/14/EY mukainen ilmoitettu tarkastuslaitos Isossa-Britanniassa ▪ Organisme notifié concernant
la directive 2000/14/CE ▪ Britische benannte Stelle für 2000/14/EG ▪ Κοινοποιημένος Οργανισμός Ηνωμένου Βασιλείου για 2000/14/ΕΚ ▪
2000/14/EK – egyesült királyságbeli bejelentett szervezet ▪ Organismo Notificato in GB per 2000/14/CE ▪ 2000/14/EK AK reģistrētā
organizācija ▪ JK notifikuotosios įstaigos 2000/14/EC ▪ Korp Notifikat tar-Renju Unit għal 2000/14/KE ▪ Dopuszczona jednostka badawcza w
Wielkiej Brytanii wg 2000/14/WE ▪ Entidade notificada no Reino Unido para 2000/14/CE ▪ Organism notificat în Marea Britanie pentru
2000/14/CE ▪ Notifikovaný orgán Spojeného kráľovstva pre smernicu 2000/14/ES ▪ Britanski priglašeni organ za 2000/14/ES ▪ Cuerpo
notificado en el Reino Unido para 2000/14/CE ▪ Anmält organ för 2000/14/EG i Storbritannien
Smithco West Inc.
200 West Poplar Avene
Cameron, WI 54822 USA
Operator Ear Noise Level ▪ Оператор на нивото на доловим от ухото шум ▪ Hladina hluku v oblasti uší operátora ▪ Støjniveau i førers
ørehøjde ▪ Geluidsniveau oor bestuurder ▪ Müratase operaatori kõrvas ▪ Melutaso käyttäjän korvan kohdalla ▪ Niveau de bruit à hauteur des
oreilles de l’opérateur ▪ Schallpegel am Bedienerohr ▪ Επίπεδο θορύβου σε λειτουργία ▪ A kezelő fülénél mért zajszint ▪ Livello di potenza
sonora all’orecchio dell’operatore ▪ Trokšņa līmenis pie operatora auss ▪ Dirbančiojo su mašina patiriamo triukšmo lygis ▪ Livell tal-Ħoss fil-
Widna tal-Operatur ▪ Dopuszczalny poziom hałasu dla operatora ▪ Nível sonoro nos ouvidos do operador ▪ Nivelul zgomotului la urechea
operatorului ▪ Hladina hluku pôsobiaca na sluch operátora ▪ Raven hrupa pri ušesu upravljavca ▪ Nivel sonoro en el oído del operador ▪
Ljudnivå vid förarens öra
85 dB(A)Lwa (2006/42/EC)
DECLARATION OF CONFORMITY ▪ ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ ▪ PROHLÁŠENÍ O SHODĚ ▪ OVERENSSTEMMELSESERKLÆRING ▪
CONFORMITEITSVERKLARING ▪ VASTAVUSDEKLARATSIOON ▪ VAATIMUSTENMUKAISUUSVAKUUTUS ▪ DECLARATION DE
CONFORMITE ▪ KONFORMITÄTSERKLÄRUNG ▪ ΔΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ▪ MEGFELELŐSÉGI NYILATKOZAT ▪ DICHIARAZIONE DI
CONFORMITÀ ▪ ATBILSTĪBAS DEKLARĀCIJA ▪ ATITIKTIES DEKLARACIJA ▪ DIKJARAZZJONI TAL-KONFORMITÀ ▪ DEKLARACJA
ZGODNOŚCI ▪ DECLARAÇÃO DE CONFORMIDADE ▪ DECLARAŢIE DE CONFORMITATE ▪ VYHLÁSENIE O ZHODE ▪ IZJAVA O SKLADNOSTI
▪ DECLARACIÓN DE CONFORMIDAD ▪ DEKLARATION OM ÖVERENSSTÄMMELSE
18
Reference
PARTS MANUALS AVAILABLE ONLINE AT smithco.com
Harmonised standards used ▪ Използвани хармонизирани стандарти ▪ Použité harmonizované normy ▪ Brugte harmoniserede standarder ▪
Gebruikte geharmoniseerde standaards ▪ Kasutatud ühtlustatud standardid ▪ Käytetyt yhdenmukaistetut standardit ▪ Normes harmonisées
utilisées ▪ Angewandte harmonisierte Normen ▪ Εναρμονισμένα πρότυπα που χρησιμοποιήθηκαν ▪ Harmonizált szabványok ▪ Standard
armonizzati applicati ▪ Izmantotie saskaņotie standarti ▪ Panaudoti suderinti standartai ▪ Standards armonizzati użati ▪ Normy spójne
powiązane ▪ Normas harmonizadas usadas ▪ Standardele armonizate utilizate ▪ Použité harmonizované normy ▪ Uporabljeni usklajeni
standardi ▪ Estándares armonizados utilizados ▪ Harmoniserade standarder som används
ANSI/OPEI B71.4:2012
BS EN ISO 13857
BS EN 349: 1993+A1:2008
BS 6356: P8
BS 6356:P5
BS EN 907
Technical standards and specifications used ▪ Използвани технически стандарти и спецификации ▪ Použité technické normy a specifikace
▪ Brugte tekniske standarder og specifikationer ▪ Gebruikte technische standaards en specificaties ▪ Kasutatud tehnilised standardid ja
spetsifikatsioonid ▪ Käytetyt tekniset standardit ja eritelmät ▪ Spécifications et normes techniques utilisées ▪ Angewandte technische Normen
und Spezifikationen ▪ Τεχνικά πρότυπα και προδιαγραφές που χρησιμοποιήθηκαν ▪ Műszaki szabványok és specifikációk ▪ Standard tecnici
e specifiche applicati ▪ Izmantotie tehniskie standarti un specifikācijas ▪ Panaudoti techniniai standartai ir techninė informacija ▪ Standards u
speċifikazzjonijiet tekniċi użati ▪ Normy i specyfikacje techniczne powiązane ▪ Normas técnicas e especificações usadas ▪ Standardele
tehnice şi specificaţiile utilizate ▪ Použité technické normy a špecifikácie ▪ Uporabljeni tehnični standardi in specifikacije ▪ Estándares y
especificaciones técnicas utilizadas ▪ Tekniska standarder och specifikationer som används
SAE J1362
The place and date of the declaration ▪ Място и дата на декларацията ▪ Místo a datum prohlášení ▪ Sted og dato for erklæringen ▪ Plaats
en datum van de verklaring ▪ Deklaratsiooni väljastamise koht ja kuupäev ▪ Vakuutuksen paikka ja päivämäärä ▪ Lieu et date de la
déclaration ▪ Ort und Datum der Erklärung ▪ Τόπος και ημερομηνία δήλωσης ▪ A nyilatkozat kelte (hely és idő) ▪ Luogo e data della
dichiarazione ▪ Deklarācijas vieta un datums ▪ Deklaracijos vieta ir data ▪ Il-post u d-data tad-dikjarazzjoni ▪ Miejsce i data wystawienia
deklaracji ▪ Local e data da declaração ▪ Locul şi data declaraţiei ▪ Miesto a dátum vyhlásenia ▪ Kraj in datum izjave ▪ Lugar y fecha de la
declaración ▪ Plats och datum för deklarationen
Smithco West Inc.
200 West Poplar Avenue
Cameron, WI 54822 USA
15-Mar-18
Signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is
authorised to compile the technical file, and who is established in the Community.Подпис на човека, упълномощен да състави
декларацията от името на производителя, който поддържащтехническата документация и е оторизиран да изготви техническия
файл и е регистриран в общността.Podpis osoby oprávněné sestavit prohlášení jménem výrobce, držet technickou dokumentaci a osoby
oprávněnésestavit technické soubory a založené v rámci Evropského společenství.Underskrift af personen, der har fuldmagt til at udarbejde
erklæringen på vegne af producenten, der er indehaveraf dokumentationen og er bemyndiget til at udarbejde den tekniske journal, og som er
baseret i nærområdet.Handtekening van de persoon die bevoegd is de verklaring namens de fabrikant te tekenen, de
technischedocumentatie bewaart en bevoegd is om het technische bestand samen te stellen, en die is gevestigd in het
Woongebied.Ühenduse registrisse kantud isiku allkiri, kes on volitatud tootja nimel deklaratsiooni koostama, kes omab
tehnilistdokumentatsiooni ja kellel on õigus koostada tehniline toimik.Sen henkilön allekirjoitus, jolla on valmistajan valtuutus vakuutuksen
laadintaan, jolla on hallussaan teknisetasiakirjat, joka on valtuutettu laatimaan tekniset asiakirjat ja joka on sijoittautunut yhteisöön.Signature
de la personne habilitée à rédiger la déclaration au nom du fabricant, à détenir la documentationtechnique, à compiler les fichiers techniques
et qui est implantée dans la Communauté.Unterschrift der Person, die berechtigt ist, die Erklärung im Namen des Herstellers abzugeben, die
dietechnischen Unterlagen aufbewahrt und berechtigt ist, die technischen Unterlagen zusammenzustellen,und die in der Gemeinschaft
niedergelassen ist.Υπογραφή ατόμου εξουσιοδοτημένου για την σύνταξη της δήλωσης εκ μέρους του κατασκευαστή, ο οποίοςκατέχει την
τεχνική έκθεση και έχει την εξουσιοδότηση να ταξινομήσει τον τεχνικό φάκελο και ο οποίος είναιδιορισμένος στην Κοινότητα.A gyártó
nevében meghatalmazott személy, akinek jogában áll módosítania a nyilatkozatot, a műszakidokumentációt őrzi, engedéllyel rendelkezik a
műszaki fájl összeállításához, és aki a közösségbenletelepedett személy.Firma della persona autorizzata a redigere la dichiarazione a nome
del fabbricante, in possesso Delladocumentazione tecnica ed autorizzata a costituire il fascicolo tecnico, che deve essere stabilita nella
Comunità.Tās personas paraksts, kura ir pilnvarota deklarācijas sastādīšanai ražotāja vārdā, kurai ir tehniskādokumentācija, kura ir
pilnvarota sagatavot tehnisko reģistru un kura ir apstiprināta Kopienā.Asmuo, kuris yra gana žinomas, kuriam gamintojas suteikė įgaliojimus
sudaryti šią deklaraciją, ir kuris jąpasirašė, turi visą techninę informaciją ir yra įgaliotas sudaryti techninės informacijos dokumentą.Il-firma tal-
persuna awtorizzata li tfassal id-dikjarazzjoni f’isem il-fabbrikant, għandha d-dokumentazzjoniteknika u hija awtorizzata li tikkompila l-fajl
tekniku u li hija stabbilita fil-Komunità.Podpis osoby upoważnionej do sporządzenia deklaracji w imieniu producenta, przechowującej
dokumentacjętechniczną, upoważnioną do stworzenia dokumentacji technicznej oraz wyznaczonej ds. wspólnotowych.Assinatura da pessoa
com poderes para emitir a declaração em nome do fabricante, que possui a documentaçãotécnica, que está autorizada a compilar o
processo técnico e que está estabelecida na Comunidade.Semnătura persoanei împuternicite să elaboreze declaraţia în numele
producătorului, care deţine documentaţiatehnică, este autorizată să compileze dosarul tehnic şi este stabilită în Comunitate.Podpis osoby
poverenej vystavením vyhlásenia v mene výrobcu, ktorá má technickú dokumentáciu a jeoprávnená spracovať technické podklady a ktorá je
umiestnená v Spoločenstve.Podpis osebe, pooblaščene za izdelavo izjave v imenu proizvajalca, ki ima tehnično dokumentacijo in
lahkosestavlja spis tehnične dokumentacije, ter ima sedež v Skupnosti.Firma de la persona responsable de la declaración en nombre del
fabricante, que posee la documentación técnicay está autorizada para recopilar el archivo técnico y que está establecido en la
Comunidad.Undertecknas av den som bemyndigad att upprätta deklarationen å tillverkarens vägnar, innehar den tekniskadokumentationen
och är bemyndigad att sammanställa den tekniska informationen och som är etablerad igemenskapen
2006/42/EC Annex II 1A: 2
John Moore
Sales, Director, Owner
Moore Turf Care
Thieplatz 4
49583 Lienen Germany
23-Sep-19
2006/42/EC Annex II 1A: 10
Dawn Bryngelson
Technical Documentation Advisor
Smithco Inc.
34 West Avenue
Wayne, PA USA 19087-3311
10-Dec-09
Certificate Number ▪ Номер на сертификат ▪ Číslo osvědčení ▪ Certifikatnummer ▪ Certificaatnummer ▪ Sertifikaadi number ▪
Hyväksyntänumero ▪ Numéro de certificat ▪ Bescheinigungsnummer ▪ Αριθμός Πιστοποιητικού ▪ Hitelesítési szám ▪ Numero del certificato ▪
Sertifikāta numurs ▪ Sertifikato numeris ▪ Numru taċ-Ċertifikat ▪ Numer certyfikatu ▪ Número do Certificado ▪ Număr certificat ▪ Číslo
osvedčenia ▪ Številka certifikata ▪ Número de certificado ▪ Certifikatsnummer
10100-2021-1
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
teistes keeltes
Seotud paberid
-
Smithco Spray Star 1110 Kasutusjuhend
-
-
-
-
-
-
-
-
-