Smithco Spraystar 2007/2007D & 2008/2008D Rate-Sync Omaniku manuaal

Bränd: Smithco

Mudel: Spraystar 2007/2007D & 2008/2008D Rate-Sync

Tüüp: Omaniku manuaal

Spray Star 2007/2008

2007D/2008D

SharpShooter-Rate Sync w/ Raven 440

with 18’ and 20’ Booms

July 2016

Operator’s

Product Support: Hwy SS & Poplar Ave; Cameron WI 54822

1-800-891-9435 productsupport@smithco.com

CONTENTS

Introduction................................................................ 1-13

Introduction ................................................................. 1

Symbols................................................................... 2-3

Safety.......................................................................... 4

Safety Decal Location................................................. 5

General Safe Practices............................................... 6

Safe Spraying Practices ............................................. 7

Specifications........................................................... 8-9

Optional Spray Equipment ....................................... 8-9

Set Up ....................................................................... 10

Controls & Instruments........................................ 12-13

Operation ................................................................. 14-30

Operating Instructions.......................................... 14-16

Re-Calibrate Flow meter........................................... 16

SharpShooter-Rate Sync Console ........................... 17

Raven 440Console Features .................................... 18

Console Programming......................................... 19-25

Initial Programming ................................................... 25

Spray Operation/Introduction................................ 26-27

Turf Management ...................................................... 28

Hose & Handgun Spraying ........................................ 28

Nozzle Trouble Shooting ...................................... 29-30

Reference ................................................................ 31-36

Collection Times ....................................................... 31

Blended Pulse Tip Selection Guide........................... 32

Declaration of Conformity ......................................

33-34

Quick Reference .................................................................36

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

INTRODUCTION

Read this manual and all other manuals pertaining to the Spray Star 2000 carefully as they contain safety, oper-

ating, assembly and maintenance instructions. Failure to do so could result in personal injury or equipment

damage.

Keep manuals in a safe place after operator and maintenance personnel have read them. Right and left sides are

from the operator’s seat, facing forward.

All

SmithcoSmithco

Smithco machines have a Serial Number and Model Number. Both numbers are needed when ordering

parts. The serial number plate on the Spray Star 2000 is located on the right middle main frame. Refer to engine

manual for placement of engine serial number. Refer to engine manual for placement of engine serial number.

For product and accessory information, help finding a dealer, or to register your procuct please contact us at

www.Smithco.com.

Information needed when ordering replacement parts:

1. Model Number of machine

2. Serial Number of machine

3. Name and Part Number of part

4. Quantity of parts

For easy access record your Serial and Model numbers here.

lb/kg Empty

lb/kg Full

CALIFORNIA

Proposition 65 Warning

Engine exhaust and some of its constituents

are known to the State of California to

cause cancer, birth defects, and other

reproductive harm.

WARNING

2PARTS MANUALS AVAILABLE ONLINE AT smithco.com

Introduction

SYMBOLS

Park Brake

Release

Hydraulic Oil

Level

Choke - OpenChoke - ClosedHand Throttle

Hour Meter Hour Meter Fuse

Glow PlugGlow Plug - OffGlow Plug - On

RPM Gasoline Diesel

Water

Temperature

Light

Engine Oil

Engine - Stop Engine - Start Engine - Run

No Electrical

Power

Electrical Power

Read Operator’s

Manual

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SYMBOLS

No Smoking Moving Parts

Manual

Operation

Pinch Point

Step Hot Surface

Hydraulic Fluid

Penetration

Lift Arm Tractor

Engage Disengage PTO

Ground Speed Fast Slow

High

Low

Forward

Reverse

Neutral

Warning

Danger

Caution

Up/RaiseDown/LowerUp/Down Arrow

4PARTS MANUALS AVAILABLE ONLINE AT smithco.com

Introduction

Safety Alert Symbol

This symbol with a warning statement means:

“Warning, be alert! Your safety is involved!”

Carefully read the message that follows.

SAFETY

Read and understand this manual and all safety signs before operating and maintaining. Review the safety

instructions and precautions annually.

TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL

YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND THE SAFETY OF

OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.

SAFETY SIGNAL WORDS

Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The

appropriate signal word for each has been selected using

the following guidelines:

DANGER: Red. Indicates an imminently hazardous

situation that, if not avoided, will result in death or serious

injury. This signal word is to be limited to the most

extreme situations typically for machine components

which, for functional purposes, cannot be guarded.

WARNING: Orange. Indicates a potentially hazardous

situation that, if not avoided, could result in death or

serious injury, and includes hazards that are exposed

when guards are removed. It may also be used to alert

against unsafe practices.

CAUTION: Yellow. Indicates a potentially hazardous

situation that, if not avoided, may result in minor or moder-

ate injury. It may also be used to alert against unsafe

practices.

IMPORTANT: Blue. Indicates procedures which should be

followed to avoid damage to the machine.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFETY DECAL LOCATION

If Safety Decals** have been damaged, removed, become illegible or parts replaced

without decals, new decals must be applied. New decals are available from your autho-

rized distributor.

This is a list of decals located on the Spray Star 2000. Part number, description and location will help in reorder-

ing a decals.

A 15-463 Decal, Spray Pump 1

B 20-545 Decal, Dash 1

C 20-553 Decal, Center Console 1

D 25-298 Decal, Warning Hot 3

E 25-321 Decal, Refuel Diesel(Diesel only) 1

25-332 Decal, Proposition 65 1

30-117 Decal, Ultra Fuel 1

F 25-375 Decal, Hydrualic Oil 1

6PARTS MANUALS AVAILABLE ONLINE AT smithco.com

Introduction

SAFE PRACTICES

1. It is your responsibility to read this manual and all publications associated with this machine.

2. Never allow anyone to operate or service the machine or its optional equipment without proper training and

instructions. Never allow minors to operate any equipment.

3. Learn the proper use of the machine, the location and purpose of all the controls and gauges before you

operate the equipment. Working with unfamiliar equipment can lead to accidents.

4. Wear all the necessary protective clothing and personal safety devises to protect your head, eyes, ears,

hands and feet. Operate the machine only in daylight or in good artificial light.

5. Inspect the area where the equipment will be used. Pick up all debris you can find before operating.

Beware of overhead obstructions and underground obstacles. Stay alert for hidden hazards.

6. Never operate equipment that is not in perfect working order or without decals, guards, shields, or other

protective devices in place.

7. Never disconnect or bypass any switch.

8. Carbon monoxide in the exhaust fumes can be fatal when inhaled, never operate a machine without proper

ventilation.

9. Fuel is highly flammable, handle with care.

10. Keep engine clean. Allow the engine to cool before storing and always remove the ignition key.

11. Disengage all drives and set park brake before starting the engine.

12. Never use your hands to search for oil leaks. Hydraulic fluid under pressure can penetrate the skin and

cause serious injury.

13. This machine demands your attention. To prevent loss of control or tipping of the vehicle:

A. Use extra caution in backing up the vehicle. Ensure area is clear.

B. Do not stop or start suddenly on any slope.

C. Reduce speed on slopes and in sharp turns. Use caution when changing directions on slopes.

D. Stay alert for holes in the terrain and other hidden hazards.

14. Before leaving operator’s position:

A. Disengage all drives.

B. Set park brake.

C. Shut engine off and remove the ignition key.

D. If engine has to run to perform any maintenance keep hands, feet, clothing and all other parts of body

away from moving parts.

15. Keep hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,

adjust or service the machine.

16. Keep the area of operation clear of all bystanders.

17. Never carry passengers unless second seat and seatbelt s installed.

18. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase.

19. Use parts and materials supplied by only. Do not modify any function or part.

20. Use caution when booms are down as they extend out beyond the center line of the machine.

21. The tank is a confined space, take precaution.

These machines are intended for professional maintenance on golf courses, sports turf, and any other

area maintained turf and related trails, paths and lots. No guaranty as to the suitability for any task is

expressed or implied.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SAFE SPRAYING PRACTICES

Persons engaged in the handling, preparation or application of chemicals must follow accepted practices to

insure the safety of themselves and others,

1. WEAR protective clothing including: gloves, hat, respirator, eye protection and skin covering suitable for

protection from chemicals being used.

2. BATHE thoroughly after any exposure to chemicals, giving particular attention to eyes, nose, ears and

mouth.

3. CLEAN equipment and materials in accordance with employer, municipal and state regulations. Use only

approved areas and drains.

4. DISPOSE of chemicals and rinse solutions by approved and legal means.

5. PROVIDE methods and materials for operators to wash eyes and hands immediately during the spraying

process.

6. PROVIDE methods and materials for control, safe dilution and neutralization of chemical spills during

preparation, spraying, transporting and cleanup.

7. Always check and follow the directions and safety warnings of the chemicals to be used.

8. Secure the discharge lines before starting the pump. An unsecured discharge line may whip.

9. Periodically inspect the pump and the system components.

10. Check hoses for weak or worn condition before each use. Make certain that all connections are tight and

secure.

11. Do not operate unit with leaks, frayed, kinked hoses or tubing. Repair or replace immediately.

12. Use only pipe, hose and fittings rated for maximum pressure or pressure at which pressure relief valve is

set at. When replacing pipe, hose or fittings, use new product.

13. Do not operate any fuel engines in an enclosed area. Be sure the area is well ventilated.

14. Do not use these pumps for pumping water or other liquids for human or animal consumption.

15. Do not pump flammable or explosive fluids such as gasoline,

fuel oil, kerosene, etc.

Do not use in explosive atmospheres. The pump should be used

only with liquids compatible with the pump component materials.

16. Be sure all exposed moving parts are guarded and that all coupling devices are securely attached before

applying power.

17. Before servicing, disconnect all power, make sure all pressure in the system is relieved, drain all liquids

from the system and flush.

18. Protect pump from freezing conditions by draining liquid and pumping rust inhibiting antifreeze solution

through the system, coating the pump interior.

19. TRANSPORT - Machine must be stopped to raise or lower booms. Because of cam sytem, if booms are

raised in transit they can fall forward or backward when coming to a stop or while traveling on uneven

terrain.

8PARTS MANUALS AVAILABLE ONLINE AT smithco.com

Introduction

SPECIFICATIONS SPRAY STAR 2000 GAS

WEIGHTS AND DIMENSIONS

Length 132" (335cm) - w/ booms 137" (348 cm) - w/ Cleanload 151" (384 cm)

Width 72" (183cm)

Height w/ Booms Folded 110" (279 cm)

Wheel Base 61" (155cm)

Weight Empty 1990 lbs (903 kg)

Weight Loaded 3605 lbs (1635 kg)

SOUND LEVEL (DB)

At ear level 84 dBA

ENGINE

Make Briggs & Stratton

Model# 543477

Type / Spec# 01143E1

Horsepower 31 hp (23 kW)

Fuel Unleaded 87 Octane Gasoline Minimum

Cooling System Air Cooled

Lubrication System Full Pressure

Alternator 20 Amp

WHEELS & TIRE Front: Two 20 x 10.00 x 10 NHS Multi-Rib; 20 psi (1.4 bar)

Rear: Two 24 x 13.00 x 12 NHS Multi-Trac; 20 psi (1.4 bar)

SPEED

Infinitely Variable 0-10 m.p.h. (0-16 kph)

BATTERY Automotive type 24F - 12 volt

BCI Group Size 24

Cold Cranking Amps 900 minimum

Ground Terminal Polarity Negative (-)

Maximum Length 10.25" (26 cm)

Maximum Width 6.88" (17 cm)

Maximum Height 10" (25 cm)

FLUID CAPACITY

Crankcase Oil See Engine Manual

Fuel 10 gallon (37,85 liters)

Hydraulic Fluid 5 gallon (19 liters)

Grade of Hydraulic Fluid SAE 10W-40 API Service SJ or higher Motor Oil

OPTIONAL EQUIPMENT

15-618 Water Meter Kit (liters) 14-515 Water Meter Kit (Gallons)

20-503 Chemical Cleanload Safe Fill 15-850 Sunshade Canopy

30-009 Manual Rewind Hose Reel, 200-foot/61-meter capacity

30-010 Electric Rewind Hose Reel, 200-foot/61-meter capacity

30-004 Foam Marker 30-006 Clear water Wash Tank

15-835 Tank Rinsing System 30-141 26 Gal Wash System

17-585 18' HD Super Boom 17-580 20' HD Super Boom

17-590 Lazer-Beam Automatic Boom for HD Booms 31-004 All Weather Top

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

SPECIFICATIONS SPRAY STAR 2000 DIESEL

WEIGHTS AND DIMENSIONS

Length 132" (335cm) - w/ booms 137" (348 cm) - w/ Cleanload 151" (384 cm)

Width 72" (183cm)

Height w/ Booms Folded 110" (279 cm)

Wheel Base 61" (155cm)

Weight Empty 1990 lbs (903 kg)

Weight Loaded 3605 lbs (1635 kg)

SOUND LEVEL (DB)

At ear level 98 dBA

ENGINE

Make Kubota

Model# D1105-E3B

Horsepower 25 hp (18.5 kW)

Fuel No.1-D or No. 2-D, S500:

Low Sulfur Diesel (LSD) less than 500 ppm or 0.05 wt.%

No1-D or No.2-D, S15: Ultra Low Sulfur Diesel (ULSD) less than 15 ppm or 0.0015 wt.%

Cooling System Liquid Cooled

Lubrication System Full Pressure

Alternator 15 Amp

WHEELS & TIRE Front: Two 20 x 10.00 x 10 NHS Multi-Rib; 20 psi (1.4 bar)

Rear: Two 24 x 13.00 x 12 NHS Multi-Trac; 18 psi (1.3 bar)

SPEED

Infinitely Variable 0-10 m.p.h. (0-16 kph)

BATTERY Automotive type 24F - 12 volt

BCI Group Size 24

Cold Cranking Amps 900 minimum

Ground Terminal Polarity Negative (-)

Maximum Length 10.25" (26 cm)

Maximum Width 6.88" (17 cm)

Maximum Height 10" (25 cm)

FLUID CAPACITY

Crankcase Oil See Engine Manual

Fuel 7 gallon (26.5 liters)

Hydraulic Fluid 5 gallon (19 liters)

Grade of Hydraulic Fluid SAE 10W-40 API Service SJ or higher Motor Oil

OPTIONAL EQUIPMENT

15-618 Water Meter Kit (liters) 14-515 Water Meter Kit (Gallons)

20-503 Chemical Cleanload Safe Fill 15-850 Sunshade Canopy

30-009 Manual Rewind Hose Reel, 200-foot/61-meter capacity

30-010 Electric Rewind Hose Reel, 200-foot/61-meter capacity

30-004 Foam Marker 30-006 Clear water Wash Tank

15-835 Tank Rinsing System 30-141 26 Gal Wash System

17-585 18' HD Super Boom 17-580 20' HD Super Boom

17-590 Lazer-Beam Automatic Boom for HD Booms 31-004 All Weather Top

10PARTS MANUALS AVAILABLE ONLINE AT smithco.com

Introduction

SETUP

The Spray Star 2000 arrives from setup and ready for service. Depending on freight conditions the

battery may have to be installed.

The spray system is normally shipped attached to the 2000 Prime Mover. If a spray system is to be fitted to a

Prime Mover by a dealer or factory, assemble and attach the components in accordance with the parts drawings

in the Spray Star 2000 Parts/Service Manual.

1. Check the tire pressure. The front and rear tires are 20 psi

(1.4 bar).

2. Battery is located under the seat. This is a negative

grounding system.

Connecting battery cables to the

wrong post could result in

personal injury and/or damage

to the electrical system. Make

sure battery and cables do not interfere or rub on

any moving part. Connect red positive (+) cable

(A) to battery first. When disconnecting remove

black negative (-) cable (B) first.

3. Check hydraulic fluid level in tank located under the seat. Remove cap and add SAE 10W-40 API Service

SJ or higher motor oil if necessary. Fluid level should be about 2-2

" (5-6.4 cm) from the top of the tank

when cold. DO NOT OVERFILL.

4. Fill fuel tank, located on the left side, with Unleaded 87 Octane gasoline (minimum) or with No. 2 diesel.

Fuel is flammable, caution must be used when storing or handling it. Do not

fill fuel tank while engine is running or an enclosed area, fumes are explo-

sive and dangerous to inhale. DO NOT SMOKE while filling the fuel tank. DO

NOT OVERFILL.

5. Machine should be greased before starting, refer to Spray Star 2000Parts/Service Manual for location.

6. Attach the Spray Boom and any other Optional Equipment to the Prime Mover, in accordance with

instructions in the Spray Star 2000 Parts/Service Manual. The nozzles must be the correct distance above

the turf as described in Turf Spraying Guide. The spray boom must operate properly and the outer sec-

tions must break away safely if an object is struck by them, they must then return to normal operation

position.

7. Be sure to double check boom heights, nozzle spacing and displacement before spraying.

8. Machine is shipped with windshield washer fluid in Spray System to prevent freezing. Flush system

completely with clear water. Fill tank with water and retighten the four bolts used to hold the tank in place.

Never allow pump to run dry! The valve on the suction side of the pump

(between the pump and tank) must be fully open whenever the pump is

operated.

9. Read operating instructions before starting.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

NOTES

12PARTS MANUALS AVAILABLE ONLINE AT smithco.com

Introduction

CONTROLS & INSTRUMENTS 2000

A. Hour Meter - The hour meter indicates hours of machine operation. It operates only when the ignition

switch is on.

B. Speedometer - The Speedometer indicates ground speed of the vehicle in miles per hour.

C. Oil Light - The oil light should come on when the ignition is on without the engine running and go out when

the engine is running. The oil light will light when the oil pressure is low. If oil light should come on, shut

engine off immediately and find the cause.

D. Ignition Switch - The ignition switch has three positions: Off - Run -

Start.

E. Tilt Steering - Hold lever down and adjust steering wheel to desired

position and release lever.

F. Lights - This rocker switch turns lights on by pushing on the top and

off by pushing on the bottom.

G. Buzzer - The buzzer sounds if the pump is running dry.

H. Ground Speed (Cruise) Control - This rocker switch initiates cruise

control by pushing on the top and turning it off by pushing on the

bottom. Works with ground Speed Control Foot switch.

I. Spray Pump - This toggle switch turns the spray pump on by

pushing on the top and off by pushing on the bottom.

J. Left Boom Switch - This rocker switch lifts and lowers the left boom.

K. Right Boom Switch - This rocker switch lifts and lowers the right

boom.

L. Hand Throttle - The hand throttle is used to regulate engine speed.

M. Choke - The choke is used in starting the engine. Pull choke out to

close choke plate when starting a cold engine. Push in when engine

starts. A warm engine may not require "choking" to start.

N. Park Brake - The park brake is only a parking brake. Pull back to

release, push forward to apply. Some adjustment can be made by

turning the knob clockwise to tighten and counter clockwise to loosen.

Introduction

PARTS MANUALS AVAILABLE ONLINE AT smithco.com

CONTROLS & INSTRUMENTS 2000

O. Spray Boss Control - Engages and disengages speed boss. Forward is engage and all the way back is

disengage. When the lever is engaged it sets a stop for the accelerator. The accelerator pedal must be

used to maintain this speed. To adjust speed use the knob on the end of the lever, counter clockwise

increases speed and clockwise decreases speed. Disengage the lever and you will have full accelerator

pedal range.

P. Cup Holder - Holds two x-alrge cups.

Q. Ground Speed (Cruise) Control Foot Switch - When rocker switch is truned on and desired speed is

obtained, push foot speed control switch to set cruise.

R. Master Boom Switch - located on the left floorboard is used to override the master switch on the computer

console of the spray systems. By pushing down it will turn on/off the booms.

For the 440 System only

the Master Switch on the computer must be off for the master boom control switch to work.

S. Accelerator Pedal - This pedal controls ground speed. Press pedal to increase speed. Varying the amount

of movement of the pedal will vary the ground speed.

T. Reverse Pedal - This pedal controls reverse. Press pedal to move machine in reverse.

Y. Water Temperature Light (Diesel Only)- Temperature light will come on and a buzzer will sound when the

engine starts to overheat.

Z. Glow Plug (Diesel Only)- When ignition is turned on, glow plug lights when ready to start.

GROUND SPEED CONTROL

When pedals are released the hydrostatic transmission centers and stops the vehicle with a braking

action.

Operation

OPERATION

Before operating the Spray Star 2000, become familiar with all controls and functions. Also complete all mainte-

nance requirements and read all safety warnings. Knowing the Spray Star 2000 thoroughly, how it operates, and

by doing the prescribed maintenance steps, you can expect trouble free operation for years to come.

SAFETY

0 needs to always be the concern of an operator of a moving vehicle or any machine with moving parts.

1. Keep all shields and guards in place.

2. Keep the parking brake engaged any time the operator is away from the vehicle or whenever service is

performed.

3. Always wear the necessary protective clothing and equipment.

4. Turn engine off when refueling or performing maintenance not specifically requiring engine power.

DAILY CHECKLIST

1. Check the engine oil level. Add as needed. DO NOT OVERFILL. Refer to engine owner's manual for oil

grade and procedure.

2. Tire pressure should be 20 psi (1.4 bar) maximum.

3. Inspect the electrical system and battery cables for loose connections or frayed wiring. Replace any faulty

equipment or tighten if loose.

4. Check hardware for loose or missing nuts, bolts, screws, etc., and tighten or replace as needed.

5. Inspect hydraulic lines for damage or leaks. Never use hands to inspect for leaks.

6. Check the hydraulic fluid level. The hydraulic fluid tank is located on the left side of the machine. The fluid

level should be 2"-2½" (5 - 6.4 cm) from the top of the tank when cold. Use only SAE 10W-40 API Service

SJ or higher Motor Oil.

7. Inspect the steering, throttle and shift linkages for good hookups and

clear travel.

8. Check controls for smooth, proper working operation. Lubricate as

needed.

9. Check park brake adjustments. Adjust as required.

10. Check anti-vibration mounts on engine frame.

STARTING THE ENGINE

1. Gas -The ignition switch is located on the dashboard. Insert the key

(A) and turn clockwise until the engine starts (C). Release the key and

it will return to the run position (B). Use the choke and hand throttle as

necessary.

2. Diesel - Insert the key (A) and turn clockwise to (B). When glow plug

light goes off Turn key to (C) until the engine starts. Release the key

and it will return to the run position (B).

3. Allow engine to idle and warm up before selecting direction of travel.

STOPPING THE ENGINE

If the engine has been running under high power, let it run at slow idle speed

a few minutes to cool the engine down, before turning the ignition switch to

the OFF position.

1. Disengage spray pump.

2. Move the throttle lever to “slow” and turn ignition key to the “off” position.

3. Remove the ignition key and engage the park brake.

Never leave the vehicle unattended with the engine running. Always bring

the vehicle to a complete stop, engage park brake, turn key off and remove

key.

Operation

OPERATION

Before using the Spray Star 2000, the operator and spray technician must familiarize themselves with all of the informa-

tion on chemical spraying contained in the Turf Spray Guide.

All testing and calibrating of sprayers is to be done with water, not chemicals. This

insures the safety to all involved in performing the calibration operation. Only after all

calibration procedures are completed should chemical be added to the sprayer.

TOWING UNIT

When it is necessary to move the Spray Star 2000 without the engine running, the bypass valve built into hydrostatic

pump must be "open" by turning it

turn to open. The valve is located on the back side of the pump. An "open" valve

allows fluid to pass through the wheels freely. When normal driven operation is desired, valve should be "closed" by

turning it clockwise. Failure to "close" the valve with engine running means no power to wheels.

HILLSIDE OPERATION

Do NOT stop or start suddenly on any slope. Be especially cautious when changing direction. Do NOT operate on

slopes greater than 10°.

BATTERY

Batteries normally produce explosive gases which can cause personal injury. Do not allow flames, sparks or any ig-

nited object to come near the battery. When charging or working near battery, always shield your eyes and always pro-

vide proper ventilation.

Battery cable should be disconnected before using “Fast Charge”.

Charge battery at 15 amps for 10 minutes or 7 amps for 30 minutes. Do not exceed the recommended charging rate. If

electrolyte starts boiling over, decrease charging.

Always remove grounded (-) battery clamp first and replace it last. Avoid hazards by:

1. Filling batteries in well-ventilated areas.

2. Wear eye protection and rubber gloves.

3. Avoid breathing fumes when electrolyte is added.

4. Avoid spilling or dripping electrolyte.

Battery Electrolyte is an acidic solution and should be handled with care. If electrolyte

is splashed on any part of your body, flush all contact areas immediately with liberal

amounts of water. Get medical attention immediately.

JUMP STARTING

Use of booster battery and jumper cables. Particular care should be used when

connecting a booster battery. Use proper polarity in order to prevent sparks.

To jump start (negative grounded battery):

1. Shield eyes.

2. Connect ends of one cable to positive (+) terminals of each

battery, first (A) then (B).

3. Connect one end of other cable to negative (-) terminal of

"good" battery (C).

4. Connect other end of cable (D) to engine block on unit being

started (NOT to negative (-) terminal of battery)

To prevent damage to other electrical components on unit being

started, make certain that engine is at idle speed before discon-

necting jumper cables.

Operation

OPERATION (CONTINUED)

SPRAYER VALVE SETTINGS AND SPRAY TANK AGITATION

The ball valve on the suction side of the pump, between the tank and the pump must be open before pump is

engaged. Close this valve only when necessary to clean the filter with spray material in the spray tank.

There is one manual flow control valve on the discharge side of the spray system. This valve controls the agita-

tor. This valve may be opened as much as necessary to provide hydraulic agitation through the quadrajet agitator

in the tank bottom. This valve may be partially closed to prevent or reduce foam buildup from the spray materials

inside the tank. When the liquid level in the spray tank reaches a certain level (usually 1-25 gallons (3.8-95 Li-

ters) depending on terrain and other conditions) it may be necessary to close the valve in the agitator line in

order to prevent loss of suction prime.

If your Spray Star is fitted with a hose reel, there is a second ball valve on the discharge system to supply mate-

rial to the hose reel.

The Quadrajet agitation system operates with four venturi jets in the tank bottom. These jets have replaceable

orifice discs which discharge the following amounts of spay material.

Input to Input to Agitator Agitator Agitator Agitator

Nozzle Agitator Agitator Pressure Pressure Output Output

Diameter in gpm in L/min in psi in bar in gpm in L/min

/8" 1.9 7.2 25 1.7 6.3 23.8

/8" 2.7 10.2 50 3.4 10.0 37.9

/8" 3.8 14.4 100 6.9 15.0 56.8

/32" 2.8 10.6 25 1.7 7.6 28.8

/32" 4.2 15.9 50 3.4 12.2 46.2

/32" 5.5 20.8 100 6.9 17.5 66.2

/16" 3.6 13.6 25 1.7 9.1 34.4

/16" 5.6 21.2 50 33.4 14.3 54.1

/16" 7.9 29.9 100 6.9 18.7 70.8

You can change orifice disc sizes to enhance spray system performance. Smaller discs reduce amount of agita-

tion (desirable in some foaming materials) and make more dischargeable liquid available for nozzles. Larger (or

none) discs increase amount of agitation and make less dischargeable liquid available for nozzles.

PROCEDURE TO RE-CALIBRATE FLOWMETER

1. Enter a Meter Cal number of 10 in Meter Cal Button

2. Enter a Total Volume of Calibrating the Pressure Gauge in Total Volume button

3. Switch Off all booms.

4. Remove a boom hose and place in calibrated 5 gallon container

5. Switch on appropriate boom switch and master switch. Pump exactly 10 gallons.

6. Readout in Total Volume is the new Meter Cal Number. Should be within 3% of number stamped on flowmeter.

7. Repeat the procedure several times to ensure accuracy.

8. To verify calibration, fill applicator tank with predetermined amount of measured liquid. DO NOT RELAY ON

GRADUATION NUMBERS ON TANK. Empty tank under normal operatin conditions. If the number under totla

volume is different from the predetermined amount of measure by more than 3% compete calculation in back of

book.

9. Enter corrected Meter Cal before resumin application.

Operation

POWER

Auto/Manual

Button

SHARPSHOOTER WITH RATE SYNC FEATURES

To Begin a Job & Create a Spray Zone

Turn Sharpshooter w/RateSync On

Press Auto/Manual button to Auto

PSI is preset.

Use arrow buttons to increase/decrease

Operation

DATA

RAVEN 440 CONSOLE FEATURES

This Console (PGM F) requires selection of US (acres); SI (hectares) or TU

(1,000 sq ft) area and SP1 (wheel drive, etc).

A. POWER - Turns Console power OFF or ON. Turning Console OFF does not affect the data stored in

the computer.

B. Select manual or fully automatic control. This can automatically control two rates.

C. Manual override control provides capability for spot spraying.

D. Booms can be controlled individually, or all at once with MASTER ON/OFF Switch

E. Displays operating rate of application and flashing Tip Fault.

F. Displays function and calibration data.

G. CE - Use like you do CE (clear entry) key on a calculator. This key is also used to select an area

base measurement of US (acres), SI (Hectares) or TU (1,000 sq ft).

H. ENTER - Used only to enter the data into the Console.

SEE QUICK REFERENCE PAGE FOR DATA THAT SHOULD BE ENTERED

Calibration Keys: (Top Row) Used to enter Function Keys: (Bottom Row) Used to display data.

data into console to calibrate the system.

BOOM 1 CAL Length of Boom 1 TOTAL AREA Total Area Sprayed

BOOM 2 CAL Length of Boom 2 FIELD AREA Field Area Sprayed

BOOM 3 CAL Length of Boom 3 FIELD VOLUME Volume Applied to Field

SPEED CAL Measured Off Drive Line DISTANCE Distance Traveled

METER CAL Flow Meter Calibration Number SPEED Speed of Vehicle

VALVE CAL Control Valve Response Time VOLUME/TANK Volume Remaining in Carrier Tank

RATE 1 CAL Target Application Rate TIME 24 hour clock (military time)

RATE 2 CAL Target Application Rate

SELF TEST Simulates Vehicle Speed

Leht laadib ...

Smithco Spraystar 2007/2007D & 2008/2008D Rate-Sync Omaniku manuaal

Bränd: Smithco

Mudel: Spraystar 2007/2007D & 2008/2008D Rate-Sync

Tüüp: Omaniku manuaal

Laadige alla PDF

aruanne

teistes keeltes

English: Smithco Spraystar 2007/2007D & 2008/2008D Rate-Sync Owner's manual

Smithco Spraystar 2007/2007D & 2008/2008D Rate-Sync Omaniku manuaal

Smithco Spraystar 2007/2007D & 2008/2008D Rate-Sync Omaniku manuaal

teistes keeltes

Seotud paberid

Muud dokumendid