Hager EEK001 User Instructions

Hager
Bränd
Hager
Mudel
EEK001
Tüüp
User Instructions
1
6E 7599.a
-
+
M
EEK001
6E 7599.a
GB
User instructions
Infrared remote control for
settings
Description
LED
Use
Battery replacement
GB
The remote control allows the user to set or
modify settings on the klik PIR occupancy
sensors when the potentiometer is on "auto
test". It allows single and multiple settings.
The SET key is used to send the IR messages
to the occupancy sensors. Multiple settings
can be stored in Memo 1 and Memo 2 and
recalled to set several devices.
Single setting
Example: do a reset.
Multiple settings
Define the parameters to be changed and
press SET to send.
Example: for 25 minutes and corridor use,
press 20', 5' and corridor.
In the case of 2 opposite states the green LED
denotes ON and the red LED denotes OFF
(except Presence/ Absence).
When no function is selected all LED’s are OFF.
+++
-
Occupancy Sensors
standalone
Occupancy Sensors
with pre-wired lead
Occupancy Sensors
with pre-wired lead
and klik.system plug
+
Technical specifications
Power supply : 1x 3V CR2032
Shelf life of battery : 2,5 years
Protection index : IP 30
The acknowledgment LED
blinks during the sending
of the IR message.
Hager SAS - 132 bld d’Europe - BP 78 - 67 212 Obernai cedex (FRANCE) - Tél. +333 88 49 50 50 - www.hagergroup.net2
Hager 10.2009
6E 7599.a
Key Meaning Indication Function
Presence Green LED on Presence on (automatic mode).
Absence Red LED on Absence on (semi automatic mode).
Power Up Green LED on The light is automatically switched ON for
30 s after power up.
Red LED on During warm up phase, the light output is off.
Reset LED on To return to factory settings
(Lux = 400, time = 20min., presence on,
power up off and cell active).
Test LED on To validate the detection area.
Time LED on To set the time.
It is possible to add times
Ex.: press 2’ and 5’, time value is 7’.
Day level
1000 Lux
LED on To set the value on 1000 Lux.
Learn LED on To learn the current Lux level.
Corridor
200 Lux
LED on To set the value on 200 Lux.
Office
400 Lux
LED on To set the value on 400 Lux.
Lux + LED on To increase the Lux level (+100).
Lux – LED on To decrease the Lux level (-100).
Active cell Green LED on The light is continuously measured.
Passive cell Red LED on The product doesn't switch the light off even
if the ambient luminosity is sufficient.
Key Meaning Indication Function
Press LED is on until a setting is changed. To load/unload Memo 1.
Long press LED is on during 5s., then blinks until release press.
After release, the LED goes off in case of setting
change.
To save the current setting as memo 1.
Press LED is on until a setting is changed. To load/unload Memo 2.
Long press LED is on during 5s., then blinks until release press.
After release, the LED goes off in case of setting
change.
To save the current setting as memo 2.
Short press (<5s) LED flashes. To send an IR message of the current setting.
Long press (>5s) only availa-
ble if no setting active.
LED blinks until release press. To toggle KNX addressing mode on OS KNX
detectors (TKK513P, TKK515P).
Settings available
Memo and SET keys
  • Page 1 1
  • Page 2 2

Hager EEK001 User Instructions

Hager
Bränd
Hager
Mudel
EEK001
Tüüp
User Instructions
Laadige alla PDF
aruanne

teistes keeltes

Seotud paberid

Muud dokumendid