POINT 3-SERIES POIH3060C4E KERAMISK TOPP Omaniku manuaal

Kategooria
Pliidiplaadid
Tüüp
Omaniku manuaal
Ceramic Hob
POIH3060C4E
User Manual
Thank you for purchasing your new POINT Ceramic Hob.
These operating instructions will help you use it properly and safely.
We recommend that you spend some time reading this instruction
manual in order that you fully understand all the operational features it
offers. Read all the safety instructions carefully before use and keep
this instruction manual for future reference.
GB
NO
Takk for at du kjøpte ditt nye POINT Keramisk platetopp.
Denne bruksanvisningen vil hjelpe deg med å bruke den på en trygg og
riktig måte. Vi anbefaler at du tar deg tid til å lese gjennom hele
bruksanvisningen for å bli fortrolig med alle funksjonene som tilbys.
Les alle sikkerhetsanvisningene nøye før bruk, og oppbevar
bruksanvisningen for fremtidig referanse.
FI
Kiitos, kun valitsit uuden POINT Keraaminen liesi.
Nämä käyttöohjeet opastavat sinua käyttämään laitetta oikein ja
turvallisesti. On suositeltavaa käyttää aikaa tämän käyttöoppaan
lukemiseen, jotta ymmärrät täysin, mitä toiminnallisia ominaisuuksia
tuote tarjoaa. Lue kaikki turvallisuusohjeet huolellisesti ennen laitteen
käyttöä ja säilytä käyttöopas myöhempää käyttöä varten.
DK
Tak for købet af dit nye Keramisk kogeplade fra POINT.
Disse brugervejledninger hjælper dig med at bruge dette apparat rigtigt og
sikkert. Vi anbefaler, at du læser denne brugervejledning, så dur en fuld
forståelse af hvordan alle funktionerne virker.s sikkerhedsforskrifterne
grundigt inden brug, og gem denne brugervejledning til senere brug.
SE
Tack för att du har köpt ditt nya Keramikhäll från POINT.
Denna bruksanvisning hjälper dig att använda den på ett säkert och
korrekt sätt. Vi rekommenderar att du tar dig tid att läsa igenom denna
bruksanvisning för att till fullo förstå alla driftfunktioner som den
erbjuder. Läs noga igenom alla säkerhetsinstruktioner före användning
och spara bruksanvisningen för framtida bruk.
2
Bruksanvisning – Svenska ......................................... sida 76 - 93
Bruksanvisning – Norsk ..............................................side 23 - 40
Instruction Manual – English ................................... page 4 - 22
Brugervejledning – Dansk ...........................................side 59 - 75
Käyttöopas - Suomi ....................................................sivu 41 - 58
3
SSafety instructions
This User Instruction Manual contains important information, including safety &
installation points, which will enable you to get the most out of your appliance. Please
keep it in a safe place so that it is easily available for future reference for you or any person
not familiar with the operation of the appliance.
Caution!
zDo not use the ceramic hob until you have
read this instruction manual. The ceramic
hob is intended for household use only.
zThe appliance becomes hot during
operation. Take care not to touch the hot
surface.
zAlways keep children away from the
ceramic hob.
zWhile in operation,direct contact with the
ceramic hob may cause burns!
zEnsure that small items of household
equipment, including connection leads, do
not touch the hob as the insulation
material of this equipment is usually not
resistant to high temperatures.
zDo not leave the ceramic hob unattended
when frying. Oils and fats may catch fire
due to overheating or boiling over.
zDo not switch on the hob until a pan has
been placed on it.
zDo not put pans weighing over 25kg on
the hob.
zDo not use the ceramic hob in the event
of a technical fault. Any faults must be
fixed by an appropriately qualified and
authorized person.
zIn the event of any incident caused by a
technical fault, disconnect the power and
report the fault to the service centre to be
repaired.
zThe rules and provisions contained in this
instruction manual should be strictly
observed. Do not allow anybody who is
not familiar with the contents of this
instruction manual to operate the ceramic
hob.
zThe ceramic hob should not be cleaned
by steam cleaninge quipment.
zIMPORTANT: The adjacent furniture or
housing and all materials used in the
installation must be able to withstand a
minimum temperature of 95°C above the
ambient temperature of the room it is
located in, whilst in use.
zAny damage caused by the appliance
being installed in contravention of this
temperature limit, or by placing adjacent
cabinet materials closer than 4mm to the
appliance, will be the liability of the owner.
zThis appliance complies with all current
European safety legislation. We do wish
to emphasize that this compliance does
not remove the fact that the appliance
surfaces will become hot during use and
retain heat after operation.
Child Safety
zWe strongly recommend that babies
and young children are prevented from
being near to the appliance and not
allowed to touch the appliance at any
time.
zIf it is necessary for younger family
members to be in the kitchen, please
ensure that they are kept under close
supervision at all times.
4
General Safety
zThis appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been
given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
zChildren should be supervised to
ensure that they do not play with the
appliance.
zNEVER try to extinguish a fire with
water, but switch off the appliance and
thencoverflamee.g.withalidorafire
blanket.
zWARNING: Danger of fire: do not store
items on the cooking surfaces.
zMeans for disconnection must be
incorporated in the fixed wiring in
accordance with the wiring rules.
zDo not allow electrical fittings or
cables to come into contact with areas
on the appliance that get hot.
zDo not use the appliance to heat the
room it is located in or to dry clothing.
zDo not install the appliance next to
curtains or soft furnishings.
zIf the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
zThe appliance is not intended to be
operated by means of an external
timer or separate remote-control
system.
zPower cord can’t accessible after
installation.
zThis product can be worked but not
through outside timer and remote
control.
zWarning: If the surface is cracked,
switch off the appliance to avoid the
possibility of electric shock, for hob
surfaces of glass ceramic or similar
material which protect live parts.
zWarning: a steam cleaner is not
allowed to be used.
zCAUTION: The cooking process has to
be supervised. A short term cooking
process has to be supervised
continuously.
zWARNING: Unattended cooking on a
hob with fat or oil can be dangerous
and may result in a fire.
zThis appliance should be connected to
a circuit which incorporates an
isolating switch which can accessible
by the user after installation providing
full disconnection from the power
supply. The disconnection may be
achieved by incorporating a switch in
the fixed wiring in accordance with the
wiring rules.
zWarning: Before obtaining access to
terminals, all supply circuits must be
disconnected.
zWARNING: Use only hob guards
designed by the manufacturer of the
cooking appliance or indicated by the
manufacturer of the appliance in the
instructions for use as suitable or hob
guards incorporated in the appliance.
The use of inappropriate guards can
cause accidents.
zWARNING: The appliance and its
accessible parts become hot during use.
zCare should be taken to avoid touching
heating elements.
zRegarding the instructions for how to
install, thanks to refer to the section
“Installation”.
5
IInstallation
Electricalconnection
Before connecting the appliance, make sure that the supply voltage marked on the Rating
Plate corresponds with your mains supply voltage.
WARNING: THISAPPLIANCE MUST BE EARTHED.
If you have to change the power cord, the earthing (yellow/green) conductor must
always be 10 mm longer than the line conductors.
Care must be taken to ensure that the temperature of the mains supply cable does not
exceed 50°C.
If the mains supply cable is damaged, then it must be replaced by an appropriate
replacement which can be obtained from Spares Department.
Assembly of ceramic hob :
6
Preparing the unit for a built-in appliance
WARNING
The kitchen units that are in direct contact with the appliances must be heat-proof (min.
95°).
The appliance can be installed on a work surface with a thickness of between 30 and 40
mm and near to walls which are higher than the work surface, maintaining a minimum
distance of 100 mm.
Carry out all cutting of the unit and work surface,then carefully remove shavings or
sawdust before inserting the appliances.
To ensure a correct ventilation of the hob,please comply with the dimensions shows in
figures.
Always refer to the manufacturer for specific instructions.
Make sure the surface is level and square and that no part interferes with the space
required for installation.
Prepare the cut as indicated (see installation dimensions).
Installing the hob
WARNING
Risk of cutting.
Be careful of cutting edges.
End parts in foamed plastic - be careful.
During transportation,these could cause slight injury or cuts.
Remove the material and envelope of documents from the packaging.
Before proceeding with installation,read the work instructions carefully.
rear of cabinet or
rear wall under
countertop
back edge
of cutout
Fig. 5
A. 40mm min
B. 40mm max
7
Step.1
Put a towel or cloth on the work surface. Place the hob face down
on the protected surface.
Step.2
Apply the strip seal, supplied with the hob, which is for sealing it
onto the work surface.
Do not use silicone. Apply the seal to the edge of the bottom of
the hob, leaving about 3mm from the edge of the glass.
Apply the seal all around the circumference.
Cut any excess and bring the two ends of the seal together so
they match.
Step.3
Fix the brackets (4 pcs) on the front side and rear side by screw. Put the hob in the cut-out
cabinet, and make it centered. Ensure that the front edge of the hob is parallel to the side edge
of the work surface.
zCarefully turn the hob back over and then gently lower it into the aperture hole that you
have cut out.
Fitting guidelines
The ceramic hob is manufactured to work with two-phase
alternating current (400V 2N~50Hz). The voltage rating of the
ceramic hob heating elements is 230V. Adapting the ceramic hob
to operate with one-phase current is possible by appropriate
Bottom of hob
Glass
surface Cloth
Seal
Self-adhesive
seal
8
bridging in the connection box according to the connection diagram below. The connection
diagram is also found on the cover of the connection box. Remember that the connection wire
should match the connection type and the power rating of the ceramic hob.
The connection cable must be secured in a strain-relief clamp.
Warning!
Remember to connect the safety circuit to the connection box terminal marked with . The
electricity supply for the ceramic hob must have a safety switch which enables the power to be
cut off in case of emergency. The distance between the working contacts of the safety switch
must be at least 3mm.
Before connecting the ceramic hob to the power supply,it is important to read the information
on the data plate and the connection diagram.
zThe cable connections must be in accordance with the diagram located on the bottom of
the hob.
zThe cable type must be connected to the corresponding power supply terminal box.
zYou should use a good quality screwdriver to carefully, fully tighten ALL of the terminal
screws.
zIf when the hob is first switched on, only two of the zones work, you should recheck that
the terminal screws are all fully tightened. This should be done before contacting the
Customer Care Department.
zIMPORTANT: The appliance must NOT be connected to the mains supply by means of a
13A plug and socket.
zThis appliance must be wired into a 30 A double pole switched fused spur outlet, having 3
mm contact separation and placed in an easily accessible position adjacent to the
appliance. It should not be located above the appliance and no more than 1.25m away
from it.
zThe cable can be looped if necessary, but make sure that is not kinked or trapped when
the hob is in position. Care must be taken to avoid the cable being in contact with hot
parts of the appliance.
Replacing the mains supply cable
If the mains supply cable is damaged, then it must be replaced by an appropriate
replacement.
The mains supply cable should be replaced in accordance with the following instructions:
¾Switch the appliance off at the control switch.
¾Open the terminal block on the underside of the hob.
9
¾Unscrew the terminal screws fixing the cable.
¾The “green-yellow” earth wire must be connected to the terminal marked .Itmust
be about 10 mm longer than the live and neutral wires.
¾The “blue” neutral wire must be connected to the terminal marked with letter (N) - the
live wire(L1) must be connected to the terminal marked with letter (L1) (220-240V
1Nν).
¾The “blue” neutral wire must be connected to the terminal marked with letter (N) - the
live wire L1 must be connected to the terminal marked with letter (L1), the live wire L2
must be connected to the terminal marked with letter (L2) (380-420V 2Nν).
Description of the Ceramic hob surface layout
4 zone ceramic hob schematic diagram
Control panel layout
1. Button and Display mode
10
1.1.1 Button icon instruction
Icons Function Icons Function
M1 NO.1 cooking zone select
button
M6 Child safety lock button: press
and hold to lock or unlock the
control panel
M2 NO.2 cooking zone select
button
M7 Timer selector: timing for each
cooking zone
M3 NO.3 cooking zone select
button
M8 Minus button: for reducing time
and power level
M4 NO.4 cooking zone select
button
M9 Power button: press and hold to
turn on or off the hob
M5 Plus button: for adding time
and power level
1.1.2 Display section
2.1 Displaymode
1) Unit digit digital tube Display corresponding parameters of the heating control, and High
temperature warning sign (“ ) of the cooking zone.
2) Two digits digital tube Display the corresponding parameters of the time and child
safety locksign.
Icons Function
1 NO.1 cookingzone indicating digital tube: display the power level, high
temperature warning symbol etc.
2 NO.2 cookingzone indicating digital tube: display the power level, high
temperature warning symbol etc.
3 NO.3 cookingzone indicating digital tube: display the power level, high
temperature warning symbol etc.
4 NO.4 cookingzone indicating digital tube: display the power level, high
temperature warning symbol etc.
5 Timer digital tube: display the time, child safety lock symbol etc.
11
Using the ceramic hob
Before first use
IMPORTANT: You should clean the ceramic hob surface (see “Maintenance and
cleaning” section).
9You should switch on one cooking zone at a time, for 5 minutes at the maximum setting.
This will help to eliminate any new smell that exists and evaporate any humidity that has
formed on the heating elements during transit.
9Do not burn off more than one zone at once.
9You must place a saucepan filled half full with cold water on each zone as you burn it off.
Operation instruction
1. Power on
9After switch on the appliance,the hob will beep for once to remind power on, all of the
indicator digital tubes on the display screen will lit on for 2s, then the appliance goes into
shutdown mode. Note: If the zone with multi-ring, the corresponding indicator digital
tube decimal point “ will lit on. If the zone with single ring only, the digital tube decimal
point “ ” will not lit on.
9Shutdown status: All the displayswill close except the high temperature warning symbol
”; At this time, only the power button “ ” can operated by pressing and holding, and
other button operations are invalid.
2. Standby mode
9Under shutdown status, press and hold “ ” button for 3s, the hob will beep for once and
then enter standby mode.
9All the indicator digital tubes of the cooking zone will display ”(The symbol “ ”will
show in the cooking zone indicator if there is residual heat), timer place will show “
as well, it will not heat at this time.
9Under standby mode, if no any cooking zone heating operation, the appliance will go into
shutdown status automatically after 10s and beep once.
3. Heating control
9Under standby mode, you can choose the cooking zone by pressing the cooking zone
select button, then press plus or minus button or to adjust the power level of the
corresponding cooking zone. Press and hold plus or minus ” buttons can
continuously to increase or decrease the power level.
9When the hob top is in heating status, press and hold “ ” power button for 3s to switch
off, and stop all the cooking zones to heat. The corresponding cooking zone indicator of
the hob top which has heated before will display high temperature warning symbol “ ”.
9Under standby mode, if some hob tops still exist residual heat, display will show “ ”.
9If needing to switch off one of the cooking zones, you can select that zone first, then
press the minus button “ ” until “0” power level to switch off that zone, and will not
affect the heating of the other cooking zones. When power level reaches “0”, the
12
corresponding cooking zone indicator of the hob top which has heated before will display
high temperature warning symbol “ ”.
9If more than one zone is operating at the same time, total power will equal to the sum of
the powers of all the working cooking zones, each cooking zone will work according to
their power modulation ratio, and will not affect each other.
Note: 1. During the same period, only one hob top button is valid, that is only one decimal
point “ can be displayed.
2. Press minus button ”to set the power level to “0”, then the heating hob top will
close automatically.
4. Multiple-ring heating function
4.1 Open double ring heating function: The outer ring can only start after the inner ring is
open.
1) Press the cooking zone select button which needs to heat, corresponding cooking zone
digital tube decimal point “ will display.
2) Press plus or minus button to select the power level you need.
3) Re-touch the cooking zone select button, cooking zone digitaltube will display single-
ring “ . Then press the cooking zone select button again to open the outer ring. After the
outer ring is opened, cooking zone digital tube will display double-ring .
4.2 Close multiple-ring heating function
1) Touch the cooking zone select button which need to heat, corresponding hob top digital
tube decimal point“ will display.
2) Touch the cooking zone select button to close the outer ring, the inner ring continues to
work.
5. Power level adjustment
Under the standby mode, press cooking zone select button to choose the corresponding
cooking zone, corresponding cooking zone digital tube decimal point “ ” and heating level
will display. You can press the plus ”and minus buttons to adjust suitable power
level.
By holding down either of these buttons, the value on the zone indicator will adjust up or
down. Each pressing “ ” button, power level will add one, until level 9, and displayed on its
corresponding digital tube. Each pressing button, power level will reduce one, until
level 0 (Each pressing of “+” or “-” button, a short audible signal will be heard). Keep
pressing “ ” or“ ” buttons will make continuously increasing or decreasing eect.
Upon completion of power level adjustment, the decimal point “ ”of digital tube will stop
flashing and normally display the power level within 10 seconds of no operation.
When switching any of the cooking zone power level to 0, it will stop the power output of
that cooking zone.
If a cooking zone has been heated, power level of all the cooking zone are “0”, the
appliance will automatically enter into shutdown status after 1 minute no operation.
6. Auto-heating function
13
Your hob can auto-heating following the below steps:
6.1 Turn on automatic heating: Press plus or minus button to set the power to level 9, then
touch plus button “ ” to let the power level alternately display “ ” and “ ”. At this time,
press minus button“ to adjust the auto-heating level you need, such as level 6. In this
automatic heating process, the corresponding power level indicating digital tube is alternately
display ” and “ ”. Alternate display time is 2.5 minutes.
6.2 Press plus button to set the power to level 9, then touch plus button “ ” to let the power
level alternately display “ ” and “ ”. At this point, the default timing has started. For example,
after ” and “ ”alternately display for 10 seconds, press the“ ” to adjust the power level to
level 6. The icons “ ” and “ ” will display for 2 minutes and 20 seconds. After 2 minutes and
20 seconds, the hob will turn to normal heating mode, corresponding power level indicating
digital tube will display “ ”.
When setting the automatic heating function, the corresponding cooking zone will be heated
in level 9 for a period of time (heating time depends on the subsequent reduction to several
levels, the heating time of each level is as follows), then continue working in the final
adjusted heating level. For example, set the heating level to 9th level and activate the
automatic heating function by pressing the “ ” key (alternately display “ ”and“ ”). Then set
the automatic heating function level to level 6 by minus button “ ”. In this setting, the
cooking zone is heated by level 9 for 2.5 minutes. The cooking zone indicating digital tube is
alternately display ” and “ ”. Then continue heating at level 6, the digital tube will display
“ ”.
6.3 The power level and time corresponding tables of auto-heating are as below:
Power Level 1 2 3 4 5 6 7 8 9
Fast-heating
time minute 1 3 4.8 6.5 8.5 2.5 3.5 4.5 5
6.4 Automatic heating level adjustment: When entering automatic heating mode, only if
auto-heating at max power within 30s, press minus button“ ” can reduce the power. After
more than 30 seconds, pressing the minus button“ ”can not reduce the automatic heating
level, it will exit the auto-heating mode.
After more than 30 seconds, as long as it is still in the automatic heating mode and the
automatic heating level is less than 9th level, press the plus button“ to increase the
automatic heating level, and the system continues to be in the automatic heating mode.
For example, after entering the automatic heating mode, within 30 seconds touch minus
button “ ” to adjust auto-heating level to level 8. The indicating digital tube will display
and “ ”. And then reduce to level 7, the indicating digital tube will display and “ ”. At this
moment, the hob is still in the automatic heating mode. When more than 30 seconds, the level
14
7 can not be reduced to level 6, the automatic heating mode can be exited, and the hob change
to normal heating mode, the indicating digital tube will display ”.
6.5 When changing the automatic heating level, the elapsed time will be automatically
calculated into the time corresponding to the new automatic heating level.
For example, you have selected the automatic heating level to be level 1 (1 minute), and after
30 seconds you change the level to level 4 (6.5 minutes). This automatic heating function will
run accurately for 6 minutes (6.5 minutes minus 30 seconds).
6.6 Within 30 seconds of automatic heating mode operation, press the minus button ” to
adjust to a certain level, then the running time is counted in the set level time.
For example, when the indicating digital tube “ ” and “ ” is alternately displayed and has
been running for 20 seconds. Press the minus button “ ” to adjust to 6th level, then the 20
seconds that have been run will be automatically counted in the 2.5 minutes of the 6th level,
while the 6th level will continue to run for 2.5 minutes minus 20 seconds, that is 2 minutes
and 10 seconds. Then turn back to normal heating mode.
7. Timer adjustment
After selecting the corresponding power of the cooking zone, press the time button“ ”, the
timer digital tube will display “00” and the decimal point on the right will display ”.
At this time, the timing mode is entered, and the timing time of the selected burner can be
set (The following operations are required in In timing mode).
If you want to cancel the timing, you can adjust the timing time to zero.
The first time you press the plus button“ ”, the timing starts from 1 minute, after which
you can press the plus or minus button to adjust the timing time.
Press the plus button“ ” for each time, the buzzer will beep once, and the heating time
will be increased by 1 minute. The timing will be continuously changed between 1-
99minutes. The maximum adjustment is to 99 minutes.
Press the minus button “ ” for each time, the buzzer will beep once, and the timing will
be reduced by 1 minute. When the timing time is less than or equal to 30 minutes, the
continuous adjustment timing will continuously change between 30-0 minutes; If the
timing has been adjusted by the plus button “ ” for more than 30 minutes, press the
minus button“ ” to adjust the timing to 0, and continue to change the timing
continuously between 30-0 by the minus button.
After the timer countdown is 0, the buzzer will continue to sound for 2 minutes, and you
can press any button to turn o the beep.
Note :
1. If the timing of a certain cooking zone has been set, to change the time, press the time
button again to select the corresponding cooking zone, and then enter the new time by
plus and minus buttons.
2. After the cooking zone is selected, the timing setting cannot be made before the cooking
zone power is set, and the time button is invalid.
3. When the timing of a certain cooking zone is set for the first time, if the cooking zone
selection button corresponding to the cooking zone is pressed when the timing is not
confirmed, the timing of the cooking zone is canceled.
15
4. When single or multiple cooking zones are working, the decimal point ” of the
corresponding cooking zone is always displayed during the timing setting process.
When multiple cooking zones are working, if two or more cooking zones have been set the
time, the timing digital tube displays the minimum timing of cook zone.The decimal point
of corresponding cooking zone is always on. The digital tube decimal point “ ” is
extinguished until the countdown time is over.
8. Power o
Under standby mode or heating mode, long press “ ” button for 3s, a short audible signal will
be heard, the appliance will go into power o mode. If the corresponding cooking zone surface
has residual heat at this time, the digital tube of power level indicator will flash display
”, and indicate residual heat warning.
9. Child Safety lock button
The control panel can be locked by pressing and holding the child safety lock button “ ”
for 3 seconds whilst the appliance is under standby status or heating status. The safety
lock icon will display. When the appliance is o, the safety lock icon will extinguish.
Under the child safety lock mode, the “ ” will display and flash (1s/time). If the cooking
zone has set the time, the digital tube will display the time and “ ” alternately. If not, it
willdisplay “ ” and “ ”.
Under the child safety lock mode, you can unlock it by pressing and holding the child lock
button “ forabout 3 seconds.
In the child safety lock mode, except for pressing and holding the power button to turn o,
as well as press and hold the child lock button to unlock, the other buttons are invalid.
10. Partition timing
The timer can be timed separately for any cooking zone, and the timing of each cooking zone
is independent of each other.
Single cooking zone timing
When setting a countdown time for a cooking zone, press timer button ” first, the digital
tube decimal point “ ”of the selected cooking zone will be on. The decimalpoint of timer
digital tube “ ”will display, and to indicate the set timer has been related with the selected
cooking zone. At this time, you can use the plus button and minus button to set the
countdown time.
Several cooking zones timing
Each timer setting operation will be same as “Single cooking zone timing”.
Press any cooking zone selection button, and the timer digital tube displays the timing
value of that cooking zone.
When multiple burners are timed, you can switch the timing of dierent burners by
pressing the time button “ ”.
When not selecting any cooking zone, the digital tube will show the minimum timer value
of cooking zones, and the digital tube of corresponding cooking zone will show “ ”.
11. Default timing
All the cooking zones have default timing function. The relationship of default timing and
power level refers to table below:
16
Power Level 1 2 3 4 5 6-9
Default timing (h) 6h 6h 5h 5h 4h 1.5h
When all the default timing is reached, the cooking zones will switch o automatically
and enter into standby mode.
12. High temperature warning
Press and hold power button “ ” manually for 3s till switch o, the whole appliance will
stop heating, but the cooking surface still has high temperature, the indicator digital tube
of corresponding cooking zone which stops heating will show residual heat warning symbol
”, to indicate corresponding cooking surface high temperature.
As long as the cooking zone has heated before, the high temperature warning symbol “
will display for 35 minutes continually after the hob turn o.
High temperature protection: The electronic temperature sensor on the control panel will
transmit the real-time temperature to the chip of the control panel. The control sensor
starts protection when the electronic temperature sensor gauges the current temperature
is higher than a certain value, reducing the heating level of the cooking zone currently,
and resumes the heating level after the temperature drops.
Residual heat protection: When the whole appliance stops heating, the digital tube of the
relative heating zone will display high temperature warning symbol “ ”, indicating that
cooking surface temperature is too high, please do not touch to avoid getting burned.
Safety cut-o protection: For the models with plug, when cut o after 1S at any time, the
voltage between L/N of the plug should fall to the safe voltage range.
13. PCB board fault codes and solutions
When a PCB board failure occurs, the timer digital tubes on the display panel always display
the fault code, and all the burners that are being heated stop heating, and automatically
return to the shutdown state after 1 minute. For the burners that have been worked, the
corresponding digital tube continues to displaythehightemperature warning sign " ". When
the fault code appears, please refer to the scheme in the following table to solve.
Fault code Type oault Solution
E1 The display board does not receive
the signal of power supply board.
The communication line failure of
power supply board or display board
can causecommunicationanomalies.
Replace the display board first. If the
fault persists, replace the power
supply board.
E2 The power supply board does not
receivethesignal of display
board.
E3 Power supply board relay failure Replace the power supply board.
E4 1. Open circuit of the display board
NTC.
2. short circuit of the display board
Replace the display board.
17
HHow to use the hot plate
Put the pot in center of the heating zone, turn the knob clockwise and anticlockwise to turn
on the hob.
High temperature indication lamp:
When the glass plate is too hot, the high temperature indication lamp will light up, don’t
touch the glass plate until the indication lamp goes out.
Shut down: after using, please turn the knob to “OFF”, the hob will stop heating.
Caution!
¾Ensure the heating plate is clean-a soiled zone does not transfer all of the heat.
¾Protect the plate against corrosion.
¾Switch off the plate against corrosion.
¾Do not leave pans with prepared dishes based on fats and oils unattended on the
switched-on plate; hot fat can spontaneously catch fire.
Hob guidelines
The first few times the hob top is used, it may give off an acrid, burning smell. This smell
will disappear completely with repeated use.
The worktop is fitted with cooking areas of different diameter and power.
The positions where the heat will radiate from are clearly marked on the hob top. The
saucepans must be positioned exactly on these zones for efficient heating to occur. Pans
should have the same diameter as the cooking zone that they are being used on.
You should not use saucepans with rough bottoms, as this can scratch the ceramic
surface.
Before use, make sure that the bottoms of the saucepans are clean and dry.
When cold, the bottom of the pans should be slightly concave, as they expand when hot
and lie flat on the surface of the hob. This will allow the heat to transfer more easily.
The best thickness for the bottom of the pans is 2 – 3 mm of enamelled steel and 4 – 6
mm for stainless steel with sandwich type bottoms.
If these rules are not followed, then there will be a great loss of heat and energy. Heat not
absorbed by the saucepan, will spread to the hob, frame and surrounding cabinets.
NTC.
E5
High temperature protection on
the display board.
Replace the Insulated silicone strip of
circuit panel first. If the fault persists,
replacethedisplay board .
wrong wrong wrong wrongright
18
Preferably cover pans with a lid to permit cooking at a lower heat.
Always cook vegetables and potatoes, etc. in as little water to reduce cooking times.
Food or liquid that has high sugar content may damage the hob top if it comes into
contact with the ceramic hob surface. Any spillages should be wiped up immediately,
however this may not prevent the hob surface from becoming damaged.
IMPORTANT: The ceramic hob surface is tough; however it is not unbreakable and can be
damaged. Especially if pointed or hard objects are allowed to fall on it with some force.
Maintenance and cleaning
Cleaning operations must only be carried out when the hob is cool.
The appliance should be disconnected from your mains supply before commencing
any cleaning process.
Cleaning the ceramic hob top
Any residues that are left on the hob top surface from cleaning agents will damage it.
You should remove any residues with warm water mixed with a little washing up liquid.
Abrasive cleaners or sharp objects will damage the hob surface; you should clean it
using warm water mixed with a little washing up liquid.
You may find it easier to clean some deposits whilst the hob surface is still warm.
However you should take care not to burn yourself if cleaning the hob surface when
it is still warm.
After each use
Wipe the appliance over with a damp cloth.
Dry the appliance by rubbing the surface with a clean cloth.
Cleaning table
Type of deposit Remove
immediately?
Remove when the
appliance
has cooled down?
What should I use to
remove the deposit?
Sugar or food/liquid
containing sugar Yes No Ceramic hob scraper
Tin foil or plastic Yes No Ceramic hob scraper
Fat splashes No Yes Ceramic hob cleaner
Metallic discolouration No Yes Ceramic hob cleaner
Water splashes or water
rings No Yes Ceramic hob cleaner
Important!
The inside of the hob should only be washed with warm water and a small amount of
washing-up liquid.
Caution!
Ensure the heating plate is clean-a soiled zone does not transfer all of the heat.
19
Protect the hob against corrosion.
Switch off the hob against corrosion.
Do not leave pans with prepared dishes based on fats and oils unattended on the switched-on
plate; hot fat can spontaneously catch fire.
IMPORTANT: If your appliance appears not to be operating correctly, Please contact
with dealer.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.
Please note that if an engineer is asked to attend whilst the product is under guarantee and
finds that the problem is not the result of an appliance fault, then you may be liable for the
cost of the call out charge.
The appliance must be accessible for the engineer to perform any necessary repair. If your
appliance is installed in such a way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then he will not complete a repair.
Specification:
Model No.: POIH3060C4E
Rated voltage: 220-240V~ or 380-420V~ 2N 50/60Hz
Total power: 6600W
Model identification POIH3060C4E
Cooking Zones 4 Zones
Supply Voltage 220-240V~ or 380-420V~ 2N 50/60Hz
Installed Electric Power 6600W
Product SizeDxW x H (mm) 580×510×49
Building-in Dimensions A x B (mm) 560×490
For circular cooking zones or area: diameter of
useful surface area per electric heated cooking
zone, rounded to the nearest 5 mm
Left down: 14.0 cm & 23.0 cm
Left up: 16.5 cm
Right down: 16.5 cm
Right up: 16.5 cm&27.0 cm
Energy consumption per cooking zone or area
calculated per kg
EC electric cooking ( Wh/kg )
Left down: 194.9
Left up: 187.1
Right down: 198.3
Right up: 193.6
Energy consumption for the hob calculated per kg
EC electric cooking ( Wh/kg ) 193.5
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94

POINT 3-SERIES POIH3060C4E KERAMISK TOPP Omaniku manuaal

Kategooria
Pliidiplaadid
Tüüp
Omaniku manuaal