SENZ SEIH1060C4N4 KERAMISK TOPP Omaniku manuaal

EVERYDAY PERFORMANCE

Ceramic Hob

SEIH1060C4N4

User Manual

Thank you for purchasing your new SENZ Ceramic Hob.

These operating instructions will help you use it properly and safely. We

recommend that you spend some time reading this instruction manual in order

to fully understand all the operational features it oers. Read all the safety

instructions carefully before use and keep this instruction manual for future

reference.

GB

NO

Takk for at du kjøpte ditt nye SENZ Keramisk platetopp.

Denne bruksanvisningen vil hjelpe deg med å bruke den på en trygg og riktig

måte. Vi anbefaler at du tar deg tid til å lese gjennom hele bruksanvisningen for

å bli fortrolig med alle funksjonene som tilbys. Les alle sikkerhetsanvisningene

nøye før bruk, og oppbevar bruksanvisningen for fremtidig referanse.

FI

Kiitos, kun valitsit uuden SENZ keraamisen keittotason.

Nämä käyttöohjeet opastavat sinua käyttämään laitetta oikein ja

turvallisesti. On suositeltavaa käyttää aikaa tämän käyttöoppaan

lukemiseen, jotta ymmärrät täysin, mitä toiminnallisia ominaisuuksia

tuote tarjoaa. Lue kaikki turvallisuusohjeet huolellisesti ennen laitteen

käyttöä ja säilytä käyttöopas myöhempää käyttöä varten.

DK

Tak for købet af dit nye Keramisk kogeplade SENZ.

Disse brugervejledninger hjælper dig med at bruge dette apparat rigtigt og sikkert.

Vi anbefaler, at du læser denne brugervejledning, så du får en fuld forståelse af

hvordan alle funktionerne virker. Læs sikkerhedsforskrifterne grundigt inden brug,

og gem denne brugervejledning til senere brug.

SE

Tack för att du har köpt ditt nya SENZ Keramikhäll.

Denna bruksanvisning hjälper dig att använda den på ett säkert och korrekt sätt.

Vi rekommenderar att du tar dig tid att läsa igenom denna bruksanvisning för

att till fullo förstå alla driftfunktioner som den erbjuder. Läs noga igenom alla

säkerhetsinstruktioner före användning och spara bruksanvisningen för

framtida bruk.

2

Bruksanvisning – Norsk ......................................side

4 - 26

27 - 48

49 - 70

71 - 92

93 - 114

Brugervejledning – Dansk ..................................side

-

– ................

3

Safety instructions

This User Instruction Manual contains important information, including safety

& installation points, which will enable you to get the most out of your

appliance. Please keep it in a safe place so that it is easily available for future

reference; for you or any person not familiar with the operation of the

appliance.

Caution!

zDo not use the ceramic hob until you

have read this instruction manual.

The ceramic hob is intended for

household use only.

zThe appliance becomes hot during

operation. Take care not to touch the

hot surface.

z Alwayskeepchildrenawayfromthe

ceramic hob.

zWhile in operation,direct contact with

the ceramic hob may cause burns!

zEnsure that small items of household

equipment, including connection leads,

do not touch the hob as the insulation

material of this equipment is usually

not resistant to high temperatures.

zDo not leave the ceramic hob

unattended when frying. Oils and fats

may catch fire due to overheating or

boiling over.

zDo not switch on the hob until a pan

has been placed on it.

zDo not put pans weighing over 25kg

on the hob.

zDo not use the ceramic hob in the

event of a technical fault. Any faults

must be fixed by an appropriately

qualified and authorized person.

zIn the event of any incident caused by

a technical fault, disconnect the

power and report the fault to the

service centre to be repaired.

zThe rules and provisions contained in

this instruction manual should be

strictly observed. Do not allow

anybody who is not familiar with the

contents of this instruction manual to

operate the ceramic hob.

zThe ceramic hob should not be

cleaned using steam cleaning

equipment.

zIMPORTANT: The adjacent furniture

or housing and all materials used in

the installation must be able to

withstand a minimum temperature of

95°C above the ambient temperature

of the room it is located in, whilst in

use.

zAny damage caused by the appliance

being installed in contravention of this

temperature limit, or by placing

adjacent cabinet materials closer than

4

4mm to the appliance, will be the

liability of the owner.

This appliance complies with all

current European safety legislation.

We do wish to emphasize that this

compliance does not remove the fact

that the appliance surfaces will

become hot during use and retain

heat after operation.

Child Safety

We strongly recommend that

babies and young children are

prevented from being near the

appliance and not allowed to touch

the appliance at any time.

It is necessary for younger family

members to be in the kitchen,

please ensure that they are kept

under close supervision at all times.

General Safety

This appliance is not intended for

use by persons (including children)

with reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge, unless

theyhavebeengiven supervision

or instruction concerning use of the

appliance by a person responsible

for their safety.

Children should be supervised to

ensure that they do not play with

the appliance.

NEVER try to extinguish a re with

water, but switch o the appliance

and then cover ame e.g. with a lid

orare blanket.

WARNING: Danger ore: do not

store items on the cooking surfaces.

Means for disconnection must be

incorporated in the xed wiring in

accordance with the wiring rules.

Do not allow electrical ttings or

cables to comeintocontact with

areas on the appliance that get hot.

Do not use the appliance to heat

the room it is located in or to dry

clothing.

Do not install the appliance next to

curtains or softfurnishings.

If the supply cord is damaged, it

must be replaced by the

manufacturer, its service agent or

similarly qualied persons in order

to avoid a hazard.

The appliance is not intended to be

operated by means of an external

timer or separate remote-control

system.

Power cord should not be accessible

installation.

This product cannot be worked

through outside timer and remote

control.

Warning: If the surface is cracked,

switch o the appliance to avoid

the possibility of electric shock, for

hob surfaces of glass ceramic or

similar material which protect live

parts.

5

Warning: a steam cleaner is not to

be used.

CAUTION: The cooking process has

to be supervised.Ashort term

cooking process has to be

supervised continuously.

WARNING: Unattended cooking on

a hob with fat or oil can be

dangerous and may result in a re.

This appliance should be

connected to a circuit which

incorporates an isolating switch

which can be accessed by the user

after installation providing full

disconnection from the power

supply. The disconnection may be

achieved by incorporating a switch

in the xed wiring in accordance

with the wiring rules.

Warning: Before obtaining access

to terminals, all supply circuits must

be disconnected.

WARNING: Only use hob guards

designed by the manufacturer of

the cooking appliance or indicated

by the manufacturer of the

appliance in the instructions for use

as suitable. The us

inappropriate guards can cause

accidents.

e of

WARNING: The appliance and its

accessible partsbecome hot during

use.

Care should be taken to avoid

touching heating elements.

Regarding the instructions for how

to install, refer to the section

“Installation”.

Installation

Electrical connection

Before connecting the appliance, make sure that the supply voltage

marked on the Rating Plate corresponds with your mains supply voltage.

WARNING: THIS APPLIANCE MUST BE EARTHED.

zIf you have to change the power cord, the earthing (yellow/green) conductor

must always be 10 mm longer than the line conductors.

zCare must be taken to ensure that the temperature of the mains supply cable does

not exceed 50°C.

zIf the mains supply cable is damaged, then it must be replaced by an appropriate

replacement which can be obtained from Spares Department.

6

Installation of ceramic hob :

Preparing the unit for a built-in appliance

WARNING

The kitchen units that are in direct contact with the appliances must be heat-

proof (min. 95°).

The appliance can be installed on a work surface with a thickness of between 30

and 40 mm and near to walls which are higher than the work surface, maintaining

a minimum distance of 100 mm.

Carry out all cuttings of the unit and work surface, then carefully remove shavings or

sawdust before inserting the appliances.

To ensure correct ventilation of the hob, please comply with the dimensions

showed in gures .

Always refer to the manufacturer for specific instructions.

Make sure the surface is level and square and that no part interferes with the space

required for installation.

Prepare the cut as indicated (see installation dimensions).

7

Installing the hob

WARNING

Risk of cutting.

Be careful of cutting edges.

End parts in foamed plastic - be careful.

During transportation,these could cause slight injury or cuts.

Remove the material and envelope of documents from the packaging.

Before proceeding with installation,read the work instructions carefully.

Step.1

Put a towel or cloth on the work surface. Place the hob face

down on the protected surface.

Step.2

Apply the strip seal, supplied with the hob, which is for sealing it onto the work surface.

Do not use silicone. Apply the seal to the edge of the bottom

of the hob, leaving about 3mm from the edge of the glass.

Apply the seal all around the circumference.

Cut any excess and bring the two ends of the seal together,

so they match.

rear of cabinet or

rear wall under

countertop

back edge

of cutout

Fig.5

A. 40mm min

B. 40mm max

Bottom of hob

Glass

surface Cloth

Seal

Self-adhesive

seal

8

Step.3

Fix the brackets (4 pcs) on the front side and rear side by screw. Put the hob in the cut-

out cabinet, and make it centered. Ensure that the front edge of the hob is parallel to

the side edge of the work surface.

IMPORTANT: You must observe the ventilation

requirements shown in the drawing opposite.

IMPORTANT: There are ventilation holes around the

outside of the hob. YOU MUST ensure that these holes

are not blocked by the work top, when you put the hob

into position (see drawing).

IMPORTANT: Do not use a silicon sealant to seal the

appliance against the aperture. This will make it

particularly if it needs to be serviced.

Carefully turn the hob back over and then gently lower it into the aperture hole

that you have cut out.

Fitting guidelines

The ceramic hob is manufactured to work with two-phase

alternating current (400V 2N~50Hz) . The voltage rating of the

ceramic hob heating elements is 230V. Adapting the ceramic

hob to operate with one-phase current is possible by

appropriate bridging in the connection box according to the

connection diagram below. The connection diagram is also

found on the cover of the connection box. Remember that the connection wire should

match the connection type and the power rating of the ceramic hob.

The connection cable must be secured in a strain-relief clamp.





9

Warning!

Remember to connect the safety circuit to the connection box terminal marked

with . The electricity supply for the ceramic hob must have a safety switch which

enables the power to be cut on case of emergency. The distance between the

working contacts of the safety switchmust be at least 3mm.

Before connecting the ceramic hob to the power supply, it is important to read the

information on the data plate and the connection diagram.

The cable connections must be in accordance with the diagram located on the

bottom of the hob.

The cable type must be connected to the corresponding power supply terminal

box.

You should use a good quality screwdriver to carefully, fully tighten ALL of the

terminal screws.

If when the hob is rst switched on, only two of the zones work, you should

recheck that the terminal screws are all fully tightened. This should be done

before contacting the Customer Care Department.

IMPORTANT: The appliance must NOT be connected to the mains supply by means

of a 13A plugandsocket.

This appliance must be wired into a 30 A double pole switched fused spur outlet,

which with 3 mm contact separation. The outlet should be placed in an easily

accessible position near the appliance. It should not be located above the appliance

and no more than 1.25m away from it.

The cable can be looped if necessary, but make sure that is not kinked or trapped

whenthe hob is in position. Care must be taken to avoid the cable being in contact

with hot parts of the appliance.

10

Replacing the mains supply cable

If the mains supply cable is damaged, then it must be replaced by an appropriate

replacement.

The mains supply cable should be replaced in accordance with the following

instructions:

¾Switch the appliance off at the control switch.

¾Open the terminal block on the underside of the hob.

¾Unscrew the terminal screws fixing the cable.

¾The “green-yellow” earth wire must be connected to the terminal marked .It

must be about 10 mm longer than the live and neutral wires.

¾The “blue” neutral wire must be connected to the terminal marked with letter (N)

- the live wire (L1) must be connected to the terminal marked with letter (L1)

(220-240V 1Nν).

¾The “blue” neutral wire must be connected to the terminal marked with letter (N)

- the live wire L1 must be connected to the terminal marked with letter (L1),

the live wire L2 must be connected to the terminal marked with letter (L2)

(380-420V 2Nν).

Description of the Ceramic hob surface layout

4 zone ceramic hob schematic diagram

11

Control panel layout

1. Button and Displaymode

1.1.1 Button icon instruction

Icons Function Icons Function

M1 NO.1 cooking zone select

button

M6 Child safety lock button: press

and hold to lock or unlock the

control panel

M2 NO.2 cooking zone select

button

M7 Timer selector: timing for each

cooking zone

M3 NO.3 cooking zone select

button

M8 Minus button: for reducing

timeand powerlevel

M4 NO.4 cooking zone select

button

M9 Power button: press and hold

to turn the hob on or o

M5 Plus button: for adding

time and power level

1.1.2 Display section

Icons Function

1 NO.1 digital cooking zone indicator: displays the power level, high

temperature warning symbol etc.

2 NO.2 digital cooking zone indicator: displays the power level, high

temperature warning symbol etc.

12

2.1 Display mode

1) Single-digit digital indicator: Displays corresponding parameters of the heating control,

and High temperature warning sign (“ ”) of the cooking zone.

2) Two-digit digital indicator: Displays the corresponding parameters of the time and

child safety lock sign.

Using the ceramic hob

Before rst use

IMPORTANT: You should clean the ceramic hob surface (see “Maintenance

and cleaning” section).

You should switch on one cooking zone at a time, for 5 minutes at the maximum

setting. This will help to eliminate any new smell that exists and evaporate any

humidity that has formed on the heating elements during transit.

Do not heat more than one zone at once.

You must place a saucepan lled halul l with cold water on each zone as you heat

it.

Operation instruction

1. Power on

After switching on the appliance, the hob will beep once to remind that power is on, all

of the digital indicators on the display screen will light up for 2s, then the appliance

goes into shutdown mode. Note: the digital indicator decimal point “ ” will not light up.

Shutdown status: All the displays will switch o except the high temperature warning

symbol “ ”; At this time, only the power button “ ” can be operated by pressing and

holding, and other button operations are invalid.

3 NO.3 digital cooking zone indicator: displays the power level, high

temperature warning symbol etc.

4 NO.4digital cooking zone indicator: displays the power level,high

temperature warning symbol etc.

5 Digital timer indicator: displays the time, child safety lock symbol etc.

13

2. Standbymode

Under shutdown status, press and hold “ ” button for 3s, the hob will bee once

and then enter standby mode.

All the digital indicators of the cooking zone will display “ ” (The symbol “ ” will

show in the cooking zone indicator if there is residual heat), timer place will show

“ ” as well, it will not heat at this time.

Under standby mode, if there is no cooking zone heating operation , the appliance

will go into shutdown status automatically after 10s and beep once.

3. Heating control

Under standby mode, you can choose the cooking zone by pressing the cooking

zone select button, then press plus or minus button to adjust the power level of

the corresponding cooking zone. Pressing and holding plus “ ” or minus “ ”

buttons can continuously increase or decrease the power level.

When the hob top is in heating status, press and hold “ ” powerbuttonfor 3s to

switch o, and stop all the cooking zones from heating. The corresponding cooking

zone indicator of the hob top which has heated before will display high

temperature warning symbol “ ”.

Under standby mode, if some hob zones still have residual heat, display will show

“ ”.

If you need to switch o one of the cooking zones,you can select that zone rst,

then press the minus button “ ” until “ 0 ” power level to switch o that zone,

without aecting the heating of the other cooking zones. When power level reaches

“0”, the corresponding cooking zone indicator of the hob zone which has heated

before will display high temperature warning symbol “ ”.

If more than one zone is operating at the same time, total power will be equal to

the sum of the powers of all the working cooking zones, each cooking zone will

work according to their power modulation ratio, and will not aect each other.

Note:. During the same period, only one hob top button is valid, that is only one

decimal point “ ” can be displayed.

2. Press minus button “ ” to set the power level to “0”, then the heating hob top

will switch o automatically.

4. Power level adjustment

Under the standby mode, press cooking zone select button to choose the

corresponding cooking zone, corresponding cooking zone digitalindicator decimal

14

point “ ” and heating level will display. You can press the plus “ ”and minus “ ”

buttons to adjust suitable power level.

By holding down either of these buttons, the value on the zone indicator will

adjust up or down. Each Each pressing of the “ ” button adds one to the power

level, until level 9, and is displayed on its corresponding digital indicator. Each

pressing of the “ ” button reduces power level by one, until level 0 (Each pressing

of “+” or “-” button, a short audible signal will be heard). Keep pressing “ ”, “ ”

buttons to continuously increase or decrease eect.

Upon completion of power level adjustment, the decimal point “ ”of digital

indicator will stop ashing and normally display the power level within 10 seconds

of no operation.

When switching any cooking zone power level to 0, it will stop the power output of

that cooking zone.

If a cooking zone has been heated but power levels of all the cooking zones are “0”,

the appliance will automatically enter into shutdown status after 1 minute of

no operation

5. Auto-heating function

Your hob can auto-heat following the steps below:

5.1 Turn on automatic heating : Press plus or minus button to set the power to level

9, then touch plus button “ ” to let the power level alternately display “ ” and “ ”. At

this time, press minusbutton“ ” to adjust the auto-heating level you need, such as

level 6. In this automatic heating process, the corresponding digital power level

indicator alternately displays “ ” and “ ”. Alternate display time is 2.5 minutes.

5.2 Press plus button to set the power to level 9, then touch plus button “ ” to let the

power level alternately display “ ” and “ ”. At this point, the default timing has

started. For example, after “ ” and “ ”alternately display for 10 seconds, press the“ ”

to adjust the power level to level 6. The icons “ ” and “ ” will display for 2 minutes and

20 seconds. After 2 minutes and 20 seconds, the hob will turn to normal heating mode,

corresponding digital power level indicator will display “ ”.

When setting the automatic heating function, the corresponding cooking zone will be

heated in level 9 for a period of time (heating time depends on the subsequent

reduction to several levels, the heating time of each level is as follows) , then continue

working in the nal adjusted heating level. For example, set the heating level to 9th

level and activate the automatic heating function by pressing the “ ” key (alternately

display “ ” “ ”). Then set the automatic heating function level to level 6 with minus

15

button “ ”. In this setting, the cooking zone is heated at level 9 for 2.5 minutes. The

digital cooking zone indicator alternately displays “ ” and “ ”. Then continue heating

at level 6, the digital indicator will display “ ”.

5.3 The power level and corresponding timetables of auto-heating are as below:

Power Level 1 2 3 4 5 6 7 8 9

Fast-heating

time

minute

1 3 4.8 6.5 8.52.5 3.5 4.5 5

5.4 Automatic heating level adjustment: When entering automatic heating

mode, only if auto-heating at max power within 30s, pressing minus button“ ” can

reduce the power. After more than 30 seconds, pressing the minus button“ ”can not

reduce the automatic heating level, it will exit the auto-heating mode.

After more than 30 seconds, as long as it is still in the automatic heating mode and the

automatic heating level is less than 9th level, press the plus button“ ” to increase

the automatic heating level, and the system continues to be in the automatic heating

mode.

For example, after entering the automatic heating mode, within 30 seconds touch

minus button “ ” to adjust auto-heating level to level 8. The digital indicator will

display “ ” and “ ”. And then reduce to level 7, the digital indicator will

“ ”. At this moment, the hob is still in the automatic heating mode. After more than 30

seconds, level 7 can not be reduced to level 6, the automatic heating mode can be

exited, and the hob changes to normal heating mode, the digital indicator

“ ”.

5.5 When changing the automatic heating level, the elapsed time will be automatically

calculatedintothe time corresponding to the new automatic heating level.

For example, you have selected the automatic heating level to be level 1 (1 minute),

and after 30 seconds you change the level to level 4 (6.5 minutes). This automatic

heating function will run accurately for 6 minutes (6.5 minutes minus 30 seconds).

5.6 Within 30 seconds of automatic heating mode operation, press the minus button

“ ” to adjust to a certain level, then the running time is counted in the set level time.

For example, when the digital indicator “ ” and “ ” is alternately displayed and has

been running for 20 seconds. Press the minus button “ ” to adjust to 6th level, then

the 20 seconds that have been run will be automatically counted in the 2.5

display “ ” and

will display

16

minutes of the 6th level, while the 6th level will continue to run for 2.5 minutes minus

20 seconds, that is 2 minutes and 10 seconds. Then turn back to normal heating mode.

6. Timer adjustment

After selecting the corresponding power of the cooking zone, press the time

button“ ”, the will display “00” and the decimal point on the right

display “ ”.

At thistime, the timing mode is entered,and the timing time of the selectedburner

can be set; (The following operations are required in timing mode).

If you want to cancel the timing, you can adjust the timing time to zero.

The rst time you press the plus button“ ”, the timing starts from 1 minute, after

which you can press the plus or minus button to adjust the timing time.

Press the plus button“ ” , for each time the buzzer will beep once, and the heating

time will be increased by 1 minute. The timing will be continuously changed

between 1-99 minutes . The maximum adjustment is to 99 minutes.

Press the minus button “ ” , for each time the buzzer will beep once, and the

timing will be reduced by 1 minute. When the timing time is less than or equal to 30

minutes, the continuous adjustment timing will continuously change between 30-

0 minutes; If the timing has been adjusted by the plus button “ ” for more than

30 minutes, press the minus button“ ” to adjust the timing to 0, and continue to

change the timing continuously between 30-0 with the minus button.

After the timer countdown is 0, the buzzer will continue to sound for 2 minutes,

and you can press any button to turn o the beep.

Note :

1. If the timing of a certain cooking zone has been set, to change the time, press the

time button again to select the corresponding cooking zone, and then enter the

new time with plus and minus buttons.

2. After the cooking zone is selected, the timing setting cannot be made before the

cooking zone power is set, and the timebutton is invalid.

3. When the timing of a certain cooking zone is set for the rst time, if the cooking

zone selection button corresponding to the cooking zone is pressed when the

timing is not conrmed, the timing of the cooking zone is canceled.

4. When single or multiple cooking zones are working, the decimal point “ ”of the

corresponding cooking zone is always displayed during the timing setting process.

When multiple cooking zonesare working, if two or more cooking zoneshave times

set, the digital timing indicator displays the minimum timing of the cooking zone

17

decimal point of corresponding cooking zone is always on. The digital indicator

decimal point “ ” is switched o until the countdown time is over.

7. Power o

Under standby mode or heating mode, long press “ ” button for 3s, a shortaudible

signal will be heard, the appliance will go into power o mode. If the corresponding

cooking zone surface has residual heat at this time, the digital power level indicator

will ash displaying

“

”, and indicate residual heat warning.

8. Child Safety lock button

The control panel can be locked by pressing and holding the child safety lock

button“ ” for 3 seconds whilst the appliance is under standby status or heating

status. The safety lock icon will display. When the appliance is switched o, the

safety lock icon will switch o.

Under the child safety lock mode, the “ ” will display and ash (1s/time). If the

cooking zone has a set time, the digital indicator will display the time and “ “

alternately. If not, it will display “ ” and “ ”.

Under the child safety lock mode, you can unlock it by pressing and holdingthe

child lock button “ ” for about 3 seconds.

In the child safety lock mode, except for pressing and holding the power button to

turn o, as well as pressing and holding the child lock button to unlock, the other

buttons are invalid.

9. Partition timing

The timer can be timed separately for any cooking zone,and the timing of each

cooking zone is independent of each other.

Single cooking zone timing

When setting a countdown time for a cooking zone, press timer button“ ” rst, the

digital indicator decimal point “ ” of the selected cooking zone will be on. The decimal

point of the digital timer “ ” will display, to indicate the set timer is related to the

selected cooking zone. At this time, you can use the plus button and minus button

to set the countdown time.

Several cooking zones timing

Each timer setting operation will be same as “Single cooking zone timing”.

Press any cooking zone selection button, and the digital timer displays the timing

value of that cooking zone.

When multiple burners are timed, you can switch the timing of dierent burners by

pressing the time button “ ”.

18

When not selecting any cooking zone, the digital indicator will show the minimum

timer value of cooking zones, and the digital indicator of corresponding cooking

zone will show “ ”.

10. Default timing

All the cooking zones have a default timing function. The relationship of default

timing and power level refers to table below:

Power Level 1 2 3 4 5 6-9

Default timing (h) 6h 6h 5h 5h 4h 1.5h

When all the default timing is reached, the cooking zones will switch o

automatically and enter into standby mode.

11. High temperature warning

Press and hold power button “ ” manuallyfor 3s till switch o,the whole

appliance will stop heating, but the cooking surface still has high temperature, the

digital indicator of corresponding cooking zone which stop heating will show

residual heat warning symbol “ ”, to indicate corresponding cooking surface high

temperature.

As long as the cooking zone has heated before, the high temperature warning

symbol “ ” will display for 35 minutes continually after the hob turns o.

High temperature protection: The electronic temperature sensor on the control

panel will transmit the real-time temperature to the chip of the control panel. The

control sensor starts protection when the electronic temperature sensor

the current temperature is higher than a certain value, to reduce the heating level

of the cooking zone currently, and resumes the heating level after the

temperature drops.

Residual heat protection:When the whole appliance stops heating, the digital

indicator of the relative heating zone will display high temperature warning

symbol “ ”, indicating that cooking surface temperature is too high, please do not

touch to avoid getting burned.

Safety cut-o protection: For the models with plug, when cut o after 1S at any

time, the voltage between L/N of the plug should fall to safe voltage range.

19

12. PCB board faultcodes and solutions

When a PCB board failure occurs, the digital timer indicators on the display panel always

display the fault code, and all the burners that are being heated stop heating, and

automatically return to the shutdown state after 1 minute. For the burners that have

been worked, the corresponding digital indicator continues to display the high

temperature warning sign " ". When the fault code appears, please refer to the

scheme in the following table to solve.

How to use the hot plate

Put the pot in the center of the heating zone,

Fault code Type oault Solution

E1 The display board does not

receive the signal of power

supply board.

The communication line failure

of power supply board or display

board can cause communication

anomalies.

Replace the display board rst.

If the fault persists, replace the

power supply board.

E2 The power supplyboard does

not receive the signal of

display board.

E3 Power supply board relay

failure

Replace the power supply board.

E4 1. Open circuit of the display

board NTC.

2.

board NTC.

Replace the display board.

E5 High temperature protection

on the display board NTC.

Replace the Insulated silicone

strip of circuit panel rst. If the

fault

b

High temperature indication lamp:

When the glass plate is too hot, the high temperature indication lamp will light up,

don’t touch the glass plate until the indication lamp goes out.

20

Leht laadib ...

SENZ SEIH1060C4N4 KERAMISK TOPP Omaniku manuaal

SENZ SEIH1060C4N4 KERAMISK TOPP Omaniku manuaal

teistes keeltes

Seotud paberid

Muud dokumendid