SENZ SEIH1060C4N KERAMISK TOPP Omaniku manuaal

SEIH1060C4N

User Manual

Ceramic Hob

Thank you for purchasing your new SENZ Ceramic Hob.

These operating instructions will help you use it properly and safely. We

recommend that you spend some time reading this instruction manual in order

that you fully understand all the operational features it oers. Read all the

safety instructions carefully before use and keep this instruction manual for

future reference.

GB

NO

Takk for at du kjøpte ditt nye SENZ Keramisk platetopp.

Denne bruksanvisningen vil hjelpe deg med å bruke den på en trygg og riktig

måte. Vi anbefaler at du tar deg tid til å lese gjennom hele bruksanvisningen for

å bli fortrolig med alle funksjonene som tilbys. Les alle sikkerhetsanvisningene

nøye før bruk, og oppbevar bruksanvisningen for fremtidig referanse.

FI

Kiitos, kun valitsit uuden SENZ Keraaminen liesi.

Nämä käyttöohjeet opastavat sinua käyttämään laitetta oikein ja

turvallisesti. On suositeltavaa käyttää aikaa tämän käyttöoppaan

lukemiseen, jotta ymmärrät täysin, mitä toiminnallisia ominaisuuksia

tuote tarjoaa. Lue kaikki turvallisuusohjeet huolellisesti ennen laitteen

käyttöä ja säilytä käyttöopas myöhempää käyttöä varten.

DK

Tak for købet af dit nye Keramisk kogeplade SENZ.

Disse brugervejledninger hjælper dig med at bruge dette apparat rigtigt og sikkert.

Vi anbefaler, at du læser denne brugervejledning, så du får en fuld forståelse af

hvordan alle funktionerne virker. Læs sikkerhedsforskrifterne grundigt inden brug,

og gem denne brugervejledning til senere brug.

SE

Tack för att du har köpt ditt nya SENZ Keramikhäll.

Denna bruksanvisning hjälper dig att använda den på ett säkert och korrekt sätt.

Vi rekommenderar att du tar dig tid att läsa igenom denna bruksanvisning för

att till fullo förstå alla driftfunktioner som den erbjuder. Läs noga igenom alla

säkerhetsinstruktioner före användning och spara bruksanvisningen för

framtida bruk.

2

Bruksanvisning – Norsk ......................................side

4 - 26

27 - 48

49 - 70

71 - 92

93 - 114

Brugervejledning – Dansk ..................................side

-

– ................

3

Safety instructions

This User Instruction Manual contains important information, including safety

& installation points, which will enable you to get the most out of your

appliance. Please keep it in a safe place so that it is easily available for future

reference; for you or any person not familiar with the operation of the

appliance.

Caution!

zDo not use the ceramic hob until you

have read this instruction manual.

The ceramic hob is intended for

household use only.

zThe appliance becomes hot during

operation. Take care not to touch the

hot surface.

z Alwayskeepchildrenawayfromthe

ceramic hob.

zWhile in operation,direct contact with

the ceramic hob may cause burns!

zEnsure that small items of household

equipment, including connection leads,

do not touch the hob as the insulation

material of this equipment is usually

not resistant to high temperatures.

zDo not leave the ceramic hob

unattended when frying. Oils and fats

may catch fire due to overheating or

boiling over.

zDo not switch on the hob until a pan

has been placed on it.

zDo not put pans weighing over 25kg

on the hob.

zDo not use the ceramic hob in the

event of a technical fault. Any faults

must be fixed by an appropriately

qualified and authorized person.

zIn the event of any incident caused by

a technical fault, disconnect the

power and report the fault to the

service centre to be repaired.

zThe rules and provisions contained in

this instruction manual should be

strictly observed. Do not allow

anybody who is not familiar with the

contents of this instruction manual to

operate the ceramic hob.

zThe ceramic hob should not be

cleaned using steam cleaning

equipment.

zIMPORTANT: The adjacent furniture

or housing and all materials used in

the installation must be able to

withstand a minimum temperature of

95°C above the ambient temperature

of the room it is located in, whilst in

use.

zAny damage caused by the appliance

being installed in contravention of this

temperature limit, or by placing

adjacent cabinet materials closer than

4

4mm to the appliance, will be the

liability of the owner.

zThis appliance complies with all

current European safety legislation.

We do wish to emphasize that this

compliance does not remove the fact

that the appliance surfaces will

become hot during use and retain

heat after operation.

Child Safety

zWe strongly recommend that

babies and young children are

prevented from being near to the

appliance and not allowed to touch

the appliance at any time.

zIf it is necessary for younger family

members to be in the kitchen,

please ensure that they are kept

under close supervision at all times.

General Safety

zThis appliance is not intended for

use by persons (including children)

with reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge, unless

they have been given supervision

or instruction concerning use of the

appliance by a person responsible

for their safety.

zChildren should be supervised to

ensure that they do not play with

the appliance.

zNEVER try to extinguish a fire with

water, but switch off the appliance

and then cover flame e.g. with a lid

or a fire blanket.

zWARNING: Danger of fire: do not

store items on the cooking surfaces.

zMeans for disconnection must be

incorporated in the fixed wiring in

accordance with the wiring rules.

zDo not allow electrical fittings or

cables to come into contact with

areas on the appliance that get hot.

zDo not use the appliance to heat

the room it is located in or to dry

clothing.

zDo not install the appliance next to

curtains or soft furnishings.

zIf the supply cord is damaged, it

must be replaced by the

manufacturer, its service agent or

similarly qualified persons in order

to avoid a hazard.

zThe appliance is not intended to be

operated by means of an external

timer or separate remote-control

system.

zPower cord can’t accessible after

installation.

zThis product can be worked but not

through outside timer and remote

control.

zWarning: If the surface is cracked,

switch off the appliance to avoid

the possibility of electric shock, for

hob surfaces of glass ceramic or

similar material which protect live

parts.

5

zWarning: a steam cleaner is not be

used.

zCAUTION: The cooking process has

to be supervised. A short term

cooking process has to be

supervised continuously.

zWARNING: Unattended cooking on

a hob with fat or oil can be

dangerous and may result in a fire.

zThis appliance should be

connected to a circuit which

incorporates an isolating switch

which can accessible by the user

after installation providing full

disconnection from the power

supply. The disconnection may be

achieved by incorporating a switch

in the fixed wiring in accordance

with the wiring rules.

Warning: Before obtaining access

to terminals, all supply circuits must

be disconnected.

WARNING: Only use hob guards

designed by the manufacturer of

the cooking appliance or indicated

by the manufacturer of the

appliance in the instructions for use

as suitable. The us

inappropriate guards can cause

accidents.

e of

WARNING: The appliance and its

accessible partsbecome hot during

use.

Care should be taken to avoid

touching heating elements.

Regarding the instructions for how

to install, refer to the section

“Installation”.

Installation

Electrical connection

Before connecting the appliance, make sure that the supply voltage

marked on the Rating Plate corresponds with your mains supply voltage.

WARNING: THIS APPLIANCE MUST BE EARTHED.

zIf you have to change the power cord, the earthing (yellow/green) conductor

must always be 10 mm longer than the line conductors.

zCare must be taken to ensure that the temperature of the mains supply cable does

not exceed 50°C.

zIf the mains supply cable is damaged, then it must be replaced by an appropriate

replacement which can be obtained from Spares Department.

6

Assembly of ceramic hob :

Preparing the unit for a built-in appliance

WARNING

The kitchen units that are in direct contact with the appliances must be heat-

proof (min. 95°).

The appliance can be installed on a work surface with a thickness of between 30

and 40 mm and near to walls which are higher than the work surface, maintaining

a minimum distance of 100 mm.

Carry out all cuttings of the unit and work surface then carefully remove shavings or

sawdust before inserting the appliances.

To ensure a correct ventilation of the hob,please comply with the dimensions

showed in figures .

Always refer to the manufacturer for specific instructions.

Make sure the surface is level and square and that no part interferes with the space

required for installation.

Prepare the cut as indicated (see installation dimensions).

7

Installing the hob

WARNING

Risk of cutting.

Be careful of cutting edges.

End parts in foamed plastic - be careful.

During transportation,these could cause slight injury or cuts.

Remove the material and envelope of documents from the packaging.

Before proceeding with installation,read the work instructions carefully.

Step.1

Put a towel or cloth on the work surface. Place the hob face

down on the protected surface.

Step.2

Apply the strip seal, supplied with the hob, which is for sealing it onto the work surface.

Do not use silicone. Apply the seal to the edge of the bottom

of the hob, leaving about 3mm from the edge of the glass.

Apply the seal all around the circumference.

Cut any excess and bring the two ends of the seal together,

so they match.

rear of cabinet or

rear wall under

countertop

back edge

of cutout

Fig.5

A. 40mm min

B. 40mm max

Bottom of hob

Glass

surface Cloth

Seal

Self-adhesive

seal

8

Step.3

Fix the brackets (4 pcs) on the front side and rear side by screw. Put the hob in the cut-

out cabinet, and make it centered. Ensure that the front edge of the hob is parallel to

the side edge of the work surface.

IMPORTANT: You must observe the ventilation

requirements shown in the drawing opposite.

IMPORTANT: There are ventilation holes around the

outside of the hob. YOU MUST ensure that these holes

are not blocked by the work top, when you put the hob

into position (see drawing).

IMPORTANT: Do not use a silicon sealant to seal the

appliance against the aperture. This will make it

particularly if it needs to be serviced.

Carefully turn the hob back over and then gently lower it into the aperture hole

that you have cut out.

Fitting guidelines

The ceramic hob is manufactured to work with two-phase

alternating current (400V 2N~50Hz) . The voltage rating of the

ceramic hob heating elements is 230V. Adapting the ceramic

hob to operate with one-phase current is possible by

appropriate bridging in the connection box according to the

connection diagram below. The connection diagram is also

found on the cover of the connection box. Remember that the connection wire should

match the connection type and the power rating of the ceramic hob.

The connection cable must be secured in a strain-relief clamp.





9

Warning!

Remember to connect the safety circuit to the connection box terminal marked

with . The electricity supply for the ceramic hob must have a safety switch which

enables the power to be cut off in case of emergency. The distance between the

working contacts of the safety switch must be at least 3mm.

Before connecting the ceramic hob to the power supply, it is important to read the

information on the data plate and the connection diagram.

zThe cable connections must be in accordance with the diagram located on the

bottom of the hob.

zThe cable type must be connected to the corresponding power supply terminal

box.

zYou should use a good quality screwdriver to carefully, fully tighten ALL of the

terminal screws.

zIf the hob is first switched on, only two of the zones work, you should

recheck that the terminal screws are all fully tightened. This should be done

before contacting the Customer Care Department.

zIMPORTANT: The appliance must NOT be connected to the mains supply by means

of a 13A plug and socket.

zThis appliance must be wired into a 30 A double pole switched fused spur outlet,

which with 3 mm contact separation. The outlet should be placed in an easily

accessible position near the appliance. It should not be located above the appliance

and no more than 1.25m away from it.

zThe cable can be looped if necessary, but make sure that is not kinked or trapped

when the hob is in position. Care must be taken to avoid the cable being in contact

with hot parts of the appliance.

10

Replacing the mains supply cable

If the mains supply cable is damaged, then it must be replaced by an appropriate

replacement.

The mains supply cable should be replaced in accordance with the following

instructions:

¾Switch the appliance off at the control switch.

¾Open the terminal block on the underside of the hob.

¾Unscrew the terminal screws fixing the cable.

¾The “green-yellow” earth wire must be connected to the terminal marked .It

must be about 10 mm longer than the live and neutral wires.

¾The “blue” neutral wire must be connected to the terminal marked with letter (N)

- the live wire (L1) must be connected to the terminal marked with letter (L1)

(220-240V 1Nν).

¾The “blue” neutral wire must be connected to the terminal marked with letter (N)

- the live wire L1 must be connected to the terminal marked with letter (L1),

the live wire L2 must be connected to the terminal marked with letter (L2)

(380-420V 2Nν).

Description of the Ceramic hob surface layout

4 zone ceramic hob schematic diagram

11

Control panel layout

1. Button and Display mode

1.1.1 Button icon instruction

Icons Function Icons Function

M1 NO.1 cooking zone select

button

M6 Child safety lock button: press

and hold to lock or unlock the

control panel

M2 NO.2 cooking zone select

button

M7 Timer selector: timing for each

cooking zone

M3 NO.3 cooking zone select

button

M8 Minus button: for reducing

time and power level

M4 NO.4 cooking zone select

button

M9 Power button: press and hold

to turn on or off the hob

M5 Plus button: for adding

time and power level

1.1.2 Display section

Icons Function

1NO.1 cooking zone indicating digital tube: display the power level,

high temperature warning symbol etc.

2NO.2 cooking-zone indicating digital tube: display the power level,

high temperature warning symbol etc.

12

2.1 Display mode

1) Unit digit digital tube: Display corresponding parameters of the heating control,

and High temperature warning sign (“ ”) of the cooking zone.

2) Two digits digital tube: Display the corresponding parameters of the time and

child safety lock sign.

Using the ceramic hob

Before first use

IMPORTANT: You should clean the ceramic hob surface (see “Maintenance

and cleaning” section).

9You should switch on one cooking zone at a time, for 5 minutes at the maximum

setting. This will help to eliminate any new smell that exists and evaporate any

humidity that has formed on the heating elements during transit.

9Do not burn off more than one zone at once.

9You must place a saucepan filled half full with cold water on each zone as you burn

it off.

Operation instruction

1. Power on

9After switch on the appliance, the hob will beep for once to remind power on, all of

the indicator digital tubes on the display screen will lit on for 2s, then the appliance

goes into shutdown mode. Note: the digital tube decimal point “ ”willnotliton.

9Shutdown status: All the displays will close except the high temperature warning

symbol “ ”; At this time, only the power button “ ” can be operated by pressing and

holding, and other button operations are invalid.

3NO.3 cooking zone indicating digital tube: display the power level,

high temperature warning symbol etc.

4NO.4 cooking zone indicating digital tube: display the power level,

high temperature warning symbol etc.

5Timer digital tube: display the time,child safety lock symbol etc.

13

2. Standby mode

9Under shutdown status, press and hold “ ” button for 3s, the hob will beep for

once and then enter standby mode.

9All the indicator digital tubes of the cooking zone will display “ ”(The symbol “ ”

will show in the cooking zone indicator if there is residual heat), timer place will

show “ ” as well, it will not heat at this time.

9Under standby mode, if no any cooking zone heating operation, the appliance will

go into shutdown status automatically after 10s and beep once.

3. Heating control

9Under standby mode, you can choose the cooking zone by pressing the cooking

zone select button, then press plus or minus button to adjust the power level of

the corresponding cooking zone. Press and hold plus “ ”orminus “ ” buttons

can continuously to increase or decrease the power level.

9When the hob top is in heating status, press and hold “” power button for 3s to

switch off, and stop all the cooking zones to heat. The corresponding cooking zone

indicator of the hob top which has heated before will display high temperature

warning symbol “ ”.

9Under standby mode, if some hob tops still exist residual heat, display will show

“”.

9If needing to switch off one of the cooking zones, you can select that zone first,

then press the minus button “ ” until “0” power level to switch off that zone, and

will not affect the heating of the other cooking zones. When power level reaches

“0”, the corresponding cooking zone indicator of the hob top which has heated

before will display high temperature warning symbol “ ”.

9If more than one zone is operating at the same time, total power will equal to the

sum of the powers of all the working cooking zones, each cooking zone will work

according to their power modulation ratio, and will not affect each other.

Note: . During the same period, only one hob top button is valid, that is only one

decimal point “ ” can be displayed.

2. Press minus button “ ”to set the power level to “0”, then the heating hob top

will close automatically.

4. Power level adjustment

9Under the standby mode, press cooking zone select button to choose the

corresponding cooking zone, corresponding cooking zone digital tube decimal

14

point “ ” and heating level will display. You can press the plus “ ”and minus “ ”

buttons to adjust suitable power level.

9By holding down either of these buttons, the value on the zone indicator will

adjust up or down. Each pressing “ ” button, power level will add one, until level 9,

and displayed on its corresponding digital tube. Each pressing “ ” button, power

level will reduce one, until level 0 (Each pressing of “+” or “-” button, a short audible

signal will be heard). Keep pressing “ ”, “ ” buttons will make continuously

increasing or decreasing effect.

9Upon completion of power level adjustment, the decimal point “”of digital tube

will stop flashing and normally display the power level within 10 seconds of no

operation.

9When switching any of the cooking zone power level to 0, it will stop the power

output of that cooking zone.

9If a cooking zone has been heated, power level of all the cooking zone are “0”, the

appliance will automatically enter into shutdown status after 1 minute no

operation.

5. Auto-heating function

Your hob can auto-heating following the below steps:

5.1 Turn on automatic heating : Press plus or minus button to set the power to level

9, then touch plus button “ ” to let the power level alternately display “ ” and “ ”. At

this time, press minus button“ ” to adjust the auto-heating level you need, such as

level 6. In this automatic heating process, the corresponding power level indicating

digital tube is alternately display “ ” and “ ”. Alternate display time is 2.5 minutes.

5.2 Press plus button to set the power to level 9, then touch plus button “ ” to let the

power level alternately display “ ” and “ ”. At this point, the default timing has

started. For example, after “ ” and “ ”alternately display for 10 seconds, press the“ ”

to adjust the power level to level 6. The icons “ ” and “ ”will display for 2 minutes and

20 seconds. After 2 minutes and 20 seconds, the hob will turn to normal heating mode,

corresponding power level indicating digital tube will display “ ”.

When setting the automatic heating function, the corresponding cooking zone will be

heated in level 9 for a period of time (heating time depends on the subsequent

reduction to several levels, the heating time of each level is as follows) , then continue

working in the final adjusted heating level. For example, set the heating level to 9th

level and activate the automatic heating function by pressing the “ ” key (alternately

display “ ”“ ”). Then set the automatic heating function level to level 6 by minus

15

button “ ”. In this setting, the cooking zone is heated by level 9 for 2.5 minutes. The

cooking zone indicating digital tube is alternately display “ ” and “ ”. Then continue

heating at level 6, the digital tube will display “ ”.

5.3 The power level and time corresponding table of auto-heating are as below:

Power Level 1 2 3 4 5 6 7 8 9

Fast-heating

time

˄minute˅

134.8 6.5 8.5 2.5 3.5 4.5 5

5.4 Automatic heating level adjustment:When entering automatic heating

mode, only if auto-heating at max power within 30s, press minus button“ ”can

reduce the power. After more than 30 seconds, pressing the minus button“ ”can not

reduce the automatic heating level, it will exit the auto-heating mode.

After more than 30 seconds, as long as it is still in the automatic heating mode and the

automatic heating level is less than 9th level, press the plus button“ ” to increase

the automatic heating level, and the system continues to be in the automatic heating

mode.

For example, after entering the automatic heating mode, within 30 seconds touch

minus button “ ”to adjust auto-heating level to level 8. The indicating digital tube

will display “ ” and “ ”. And then reduce to level 7, the indicating digital tube will

display “ ” and “ ”. At this moment, the hob is still in the automatic heating mode.

When more than 30 seconds, the level 7 can not be reduced to level 6, the automatic

heating mode can be exited, and the hob change to normal heating mode, the

indicating digital tube will display “ ”.

5.5 When changing the automatic heating level, the elapsed time will be automatically

calculated into the time corresponding to the new automatic heating level.

For example, you have selected the automatic heating level to be level 1 (1 minute),

and after 30 seconds you change the level to level 4 (6.5 minutes). This automatic

heating function will run accurately for 6 minutes (6.5 minutes minus 30 seconds).

5.6 Within 30 seconds of automatic heating mode operation, press the minus button

“” to adjust to a certain level, then the running time is counted in the set level time.

For example, when the indicating digital tube “ ” and “ ”is alternately displayed and

has been running for 20 seconds. Press the minus button “ ”toadjustto6thlevel

,

then the 20 seconds that have been run will be automatically counted in the 2.5

16

minutes of the 6th level, while the 6th level will continue to run for 2.5 minutes minus

20 seconds, that is 2 minutes and 10 seconds. Then turn back to normal heating mode.

6. Timer adjustment

After selecting the corresponding power of the cooking zone, press the time

button“ ”, the timer digital tube will display “00” and the decimal point on the right

will display “ ”.

At this time, the timing mode is entered, and the timing time of the selected burner

can be set; (The following operations are required in timing mode).

9If you want to cancel the timing, you can adjust the timing time to zero.

9The first time you press the plus button“ ”, the timing starts from 1 minute, after

which you can press the plus or minus button to adjust the timing time.

9Press the plus button“ ” for each time, the buzzer will beep once, and the heating

time will be increased by 1 minute. The timing will be continuously changed

between 1-99 minutes . The maximum adjustment is to 99 minutes.

9Press the minus button “ ”for each time, the buzzer will beep once, and the

timing will be reduced by 1 minute. When the timing time is less than or equal to 30

minutes, the continuous adjustment timing will continuously change between 30-

0 minutes; If the timing has been adjusted by the plus button “ ”formorethan

30 minutes, press the minus button“ ” to adjust the timing to 0, and continue to

change the timing continuously between 30-0 by the minus button.

9After the timer countdown is 0, the buzzer will continue to sound for 2 minutes,

and you can press any button to turn off the beep.

Note :

1. If the timing of a certain cooking zone has been set, to change the time, press the

time button again to select the corresponding cooking zone, and then enter the

new time by plus and minus buttons.

2. After the cooking zone is selected, the timing setting cannot be made before the

cooking zone power is set, and the time button is invalid.

3. When the timing of a certain cooking zone is set for the first time, if the cooking

zone selection button corresponding to the cooking zone is pressed when the

timing is not confirmed, the timing of the cooking zone is canceled.

4. When single or multiple cooking zones are working, the decimal point “ ”of the

corresponding cooking zone is always displayed during the timing setting process.

When multiple cooking zones are working, if two or more cooking zones have been

set the time, the timing digital tube displays the minimum timing of cook zone. The

17

decimal point of corresponding cooking zone is always on. The digital tube decimal

point “ ” is extinguished until the countdown time is over.

7. Power off

Under standby mode or heating mode, long press “ ” button for 3s, a short audible

signal will be heard, the appliance will go into power off mode. If the corresponding

cooking zone surface has residual heat at this time, the digital tube of power level

indicator will flash displaying “ ”, and indicate residual heat warning.

8. Child Safety lock button

9The control panel can be locked by pressing and holding the child safety lock

button“ ” for 3 seconds whilst the appliance is under standby status or heating

status. The safety lock icon will display. When the appliance is switched off,the

safety lock icon will extinguish.

9Under the child safety lock mode, the “ ” will display and flash (1s/time). If the

cooking zone has set the time, the digital tube will display the time and “ ”

alternately. If not, it will display “ ” and “ ”.

9Under the child safety lock mode, you can unlock it by pressing and holding the

child lock button “ ” for about 3 seconds.

9In the child safety lock mode, except for pressing and holding the power button to

turn off, as well as press and hold the child lock button to unlock, the other buttons

are invalid.

9. Partition timing

The timer can be timed separately for any cooking zone, and the timing of each

cooking zone is independent of each other.

zSingle cooking zone timing

When setting a countdown time for a cooking zone, press timer button“ ”first,the

digital tube decimal point “ ”of the selected cooking zone will be on. The decimal

point of timer digital tube “ ”will display, and to indicate the set timer has been

related with the selected cooking zone. At this time, you can use the plus button

and minus button to set the countdown time.

zSeveral cooking zones timing

Each timer setting operation will be same as “Single cooking zone timing”.

Press any cooking zone selection button, and the timer digital tube display the

timing value of that cooking zone.

When multiple burners are timed, you can switch the timing of different burners by

pressing the time button “ ”.

18

When not selecting any cooking zone, the digital tube will show the minimum timer

value of cooking zones, and the digital tube of corresponding cooking zone will

show “ ”.

10. Default timing

9All the cooking zones have default timing function. The relationship of default

timing and power level refers to table below:

Power Level 1 2 3 4 5 6-9

Default timing (h) 6h 6h 5h 5h 4h 1.5h

9When all the default timing is reached, the cooking zones will switch off

automatically and enter into standby mode.

11. High temperature warning

9Press and hold power button “ ” manually for 3s till switch off, the whole

appliance will stop heating, but the cooking surface still has high temperature, the

indicator digital tube of corresponding cooking zone which stop heating will show

residual heat warning symbol “ ”, to indicate corresponding cooking surface high

temperature.

9As long as the cooking zone has heated before, the high temperature warning

symbol “ ” will display for 35 minutes continually after the hob turn off.

9High temperature protection: The electronic temperature sensor on the control

panel will transmit the real-time temperature to the chip of the control panel. The

control sensor starts protection when the electronic temperature sensor gauges

the current temperature is higher than a certain value, to reduce the heating level

of the cooking zone currently, and resumes the heating level after the

temperature drops.

9Residual heat protection: When the whole appliance stops heating, the digital

tube of the relative heating zone will display high temperature warning symbol

“”, indicating that cooking surface temperature is too high, please do not touch to

avoid getting burned.

9 Safety cut-off protection: For the models with plug, when cut off after 1S at any

time, the voltage between L/N of the plug should fall to the safe voltage range.

19

12. PCB board fault codes and solutions

When a PCB board failure occurs, the timer digital tubes on the display panel always

display the fault code, and all the burners that are being heated stop heating, and

automatically return to the shutdown state after 1 minute. For the burners that have

been worked, the corresponding digital tube continues to display the high

temperature warning sign " ". When the fault code appears, please refer to the

scheme in the following table to solve.

How to use the hot plate

Put the pot in center of the heating zone, turn the knob clockwise and anticlockwise

to turn on the hob.

High temperature indication lamp:

When the glass plate is too hot, the high temperature indication lamp will light up,

don’t touch the glass plate until the indication lamp goes out.

Fault code Type of fault Solution

E1 The display board does not

receive the signal of power

supply board.

The communication line failure

of power supply board or display

board can cause communication

anomalies.

Replace the display board first.

If the fault persists, replace the

power supply board.

E2 The power supply board does

not receive the signal of

display board.

E3 Power supply board relay

failure

Replace the power supply board.

E4 1. Open circuit of the display

board NTC.

2. Short circuit of the display

board NTC.

Replace the display board.

E5 High temperature protection

on the display board NTC.

Replace the Insulated silicone

strip of circuit panel first. If the

fault persists, replace the display

board.

20

Leht laadib ...

SENZ SEIH1060C4N KERAMISK TOPP Omaniku manuaal

SENZ SEIH1060C4N KERAMISK TOPP Omaniku manuaal

teistes keeltes

Seotud paberid

Muud dokumendid