Sentiotec Concept R mini combi Kasutusjuhend

Version 07/23 Ident. no. CP-RMC-MA

INSTRUCTIONS FOR INSTALLATION AND USE

English

EN

DE

FR

SV

FI

Sauna heater

Concept R mini combi

CP-RMC-35 / 1-041-405: Concept R mini combi 3.5 kW

CP-RMC-45 / 1-041-406: Concept R mini combi 4.5 kW

CP-RMC-60 / 1-041-407: Concept R mini combi 6.0 kW

CP-RMC-75 / 1-041-408: Concept R mini combi 7.5 kW

Table of Contents

1. About this instruction manual 4

2. Important information for your safety 5

2.1. Intended use 5

2.2. Safety information for the installer 5

2.3. Safety information for the user 7

3. Product description 9

3.1. Scope of delivery 9

3.2. Accessories 9

3.3. Product functions 9

4. Installation and connection 10

4.1. Installation location and sensor position 10

4.2. Safety intervals 11

4.3. Installation on the cabin wall 12

4.4. Installation with foot (optional) 14

4.5. Connection diagram for 400V 3N~ 16

4.6. Connection diagram for 230V 1N~ 17

4.7. Wiring diagrams 18

4.8. Electrical connection 19

4.9. Installing the heater railing (optional) 20

5. Commissioning 23

5.1. Filling the stone container 23

5.2. Inserting the ceramic bowl 23

5.3. Heatingforthersttime 24

EN

6. Operation 25

6.1. Finnish sauna mode 25

6.2. Combi mode 26

7. Maintenance 28

7.1. Extended periods of non-use 28

7.2. Cleaning the sauna heater 28

7.3. Changing the sauna stones 29

7.4. Cleaning the evaporator tank 29

7.5. Cleaning the ceramic bowl 30

7.6. Descaling the evaporator tank 30

8. Disposal 30

9. Problem-solving by the installer 31

10. Technical data 32

Instructions for installation and use p. 4/32

1. About this instruction manual

Carefully read these instructions for installation and use, and keep them near

the sauna. This ensures that you can refer to information about your safety and

the operation at any time.

Symbols used for warning notices

In these instructions for installation and use, a warning notice located next to

an activity indicates that this activity poses a risk. Always observe the warning

notices. This prevents damage to property and injuries, which in the worst case

may be fatal.

The warning notices contain keywords, which have the following meanings:

DANGER!

Serious or fatal injury will occur if this warning notice is not observed.

WARNING!

Serious or fatal injury can occur if this warning notice is not observed.

CAUTION!

Minor injuries can occur if this warning notice is not observed.

ATTENTION!

This keyword is a warning that damage to property can occur.

Other symbols

This symbol indicates tips and useful information.

Do not cover Read the operating instructions

These installation and operating instructions can also be found in the

downloads section of our website: www.sentiotec.com/downloads.

EN

Instructions for installation and use p. 5/32

2. Important information for your safety

The Concept R mini combi sauna heater has been produced in ac-

cordance with the applicable safety rules and regulations. However,

hazards may occur during use. Therefore adhere to the following

safetyinformationandthespecicwarningnoticesintheindividual

chapters.

2.1. Intended use

The Concept R mini combi is a sauna heater with integrated evapora-

tor. The Concept R mini combi may only be used for heating sauna

cabins and for increasing the humidity inside the sauna cabin.

The Concept R mini combi must only be used in combination with

a sauna control unit that does not include remote start functions.

Any use exceeding this scope is considered improper use. Improper

use can result in damage to the product, severe injuries or death.

2.2. Safety information for the installer

●Installing and connecting the sauna heater may only be performed

when the power supply is disconnected.

●Installationmayonlybeperformedbyaqualiedelectricianor

similarlyqualiedperson.

●A fully disconnecting all-pole isolating device compliant with

overvoltagecategoryIIImustbettedonsite.

●Always use silicone cables that are heat-resistant up to 150 °C

to connect the sauna heater.

●Only install one sauna heater in the cabin. The Concept R mini

combi sauna heater must not be used together with other sauna

heaters in a sauna cabin.

Instructions for installation and use p. 6/32

●The roof and walls of the sauna cabin must be manufactured

from low-resin, untreated or thermally treated wood, e.g. Nordic

spruce,hemlock,pineorr,orfromlaminatedwoodenmateri-

als. If laminated wooden materials are used, make sure that the

adhesive used in them does not produce formaldehyde. If other

materials than wood are used in the sauna cabin, these materi-

als must be heat-resistant and corrosion-resistant and must not

causeanynegativeeectsonthehealthofthesaunausers.

●The height of the sauna cabin must be at least 1.64 m.

● Observethespecicationsonvolumesandonventilationofthe

sauna cabin in chapter 10. Technical data.

●When positioning the sauna heater, observe the minimum safety

distances (see chapter 4.2. Safety intervals).

●Also comply with the regulations applicable at the installation

location.

●For your own safety, consult your supplier in the event of prob-

lemsthatarenotexplainedinsucientdetailintheinstallation

instructions.

2.3. Safety information for the user

●The device must not be used by children under 8 years old.

●The device may only be used by children over 8 years old, by

persons with limited psychological, sensory or mental capabili-

ties or by persons with lack of experience/knowledge under the

following conditions:

– They are supervised.

– They have been shown how to use the device safely and

are aware of the hazards that could occur.

EN

Instructions for installation and use p. 7/32

●Children must not play with the device.

●Children under 14 years old may only clean the device if they

are supervised.

● Forhealthreasons,donotusethesaunawhenundertheinu-

ence of alcohol, medication or drugs.

●Never operate the sauna heater without sauna stones as this

cancauseres.

● Makesurethatnoammableobjectshavebeenplacedonthe

sauna heater before the sauna control unit is switched on.

●Heat up the sauna heater for half an hour BEFORE using the

saunaforthersttime.DoNOTremaininthesaunacabinduring

this period. Then ventilate the sauna cabin well (see 5.3. Heating

for the rst time on page 23).

●Never touch the sauna heater while it is operating. The surfaces

of the sauna heater and sauna stones become extremely hot.

●NEVERpourwaterintothehotevaporatortank.Checkandll

the evaporator tank each time before starting combi mode. If the

overheatingprotectionhasswitchedoevaporatorheating,orif

your sauna control unit reports a lack of water, allow the evaporator

to cool down BEFORE you pour water into the evaporator tank.

●For your own safety, consult your supplier in the event of prob-

lemsthatarenotdescribedinsucientdetailintheoperating

instructions.

Instructions for installation and use p. 8/32

3. Product description

3.1. Scope of delivery

●Sauna heater

●Instructions for installation and use

3.2. Accessories

Accessories Item number

Set of brackets for the Concept R mini combi

heater railing

CP-RMC-HSR / 1-041-410

Wood railing for Concept R mini combi, lime wood CP-RMC-L / 1-041-412

Wood railing for Concept R mini combi, walnut CP-RMC-N / 1-041-411

Foot for Concept R mini combi CP-RMC-SF / 1-041- 409

Cover foot for Concept R mini, lime wood CP-RM-CSF-L / 1-041482

Cover foot for Concept R mini, walnut

CP-RM-CSF-N / 1-041-483

3.3. Product functions

●Finnish sauna mode: usually 80 to 100 °C; approx. 10% rel. humidity

●Combi mode (only in combination with a combi control): approx. 40 to 65 °C,

35% to 70% humidity. The maximum permissible relative humidity decreases

with increasing temperature.

If you wish, you can put fragrances or dried herbs in the ceramic bowl over

the evaporator in combi mode. The rising steam releases essential oils from

theherbsandfragrancesllthesaunacabin.

EN

Installation instructions, for professionals only p. 9/32

WARNING!

Danger of electric shock

●The sauna heater may only be installed and connected when the power

supply is disconnected.

4. Installation and connection

Take the following points into account when positioning and connecting the sauna

heater:

●Theelectricalconnectionmayonlybeperformedbyaqualiedelectricianor

similarlyqualiedperson.

●A fully disconnecting all-pole isolating device compliant with overvoltage

categoryIIImustbettedonsite.

●The Concept R mini combi sauna heater can be used as a wall-mounted

heater or as a free-standing heater. When mounted to the wall, check that

theheaterhasbeenrmlyinstalledonthemountingrailbeforestartingheater

operation.Wheninstallingthedevicewithfoot,checkthatthefootingisrm.

4.1. Installation location and sensor position

Position the heater centrally in front of the air intake opening on the cabin wall.

ComplywiththesafetyintervalstothecabinwallspeciedinFig. 1.

Install the temperature sensor with overheat cut-out to the cabin wall above the

centre of the sauna heater. Maintain a distance of 15 cm to the sauna cabin roof.

min 50

580

min 130 min 900

687

220 50

100

20

Installation instructions, for professionals only p. 10/32

Fig. 1 Safety intervals

for the Concept R mini combi 3.5 kW, 4.5 kW, 6.0 kW and 7.5 kW

(CP-RMC-35 / CP-RMC-45 / CR-RMC-60 / CP-RMC-75)

Dimensions in mm

4.2. Safety intervals

ObservetheminimumsafetyintervalsspeciedinFig. 1.

EN

Installation instructions, for professionals only p. 11/32

4.3. Installation on the cabin wall

Observe Fig. 1, Fig. 2, Fig. 3 and Fig. 4 (page 11, 12, 13).

1. Attach the mounting rail 1 to the wall horizontally using the wood screws

supplied 2. Observe the minimum intervals for the heater shown in Fig. 1.

2. Suspend the heater 3 from the mounting rail from above, moving it down-

wards.Makesurethattheheaterisushwiththewall.

3. Secure the heater 3 using the lock screws supplied 4 on the mounting

rail 1.

Fig. 2 Position of the mounting rail for Concept R mini combi

Dimensions in mm

2

WARNING!

Risk of re

●Toxtheheaterinplaceandsecureitagainstslippage,usethe

supplied lock screw 4 for attachment.

1

170 170

360

340

Installation instructions, for professionals only p. 12/32

63

110 110

Fig. 3 Position of the mounting rail for Concept R mini combi

Dimensions in mm

Fig. 4 Securing the Concept R mini combi (mounting rail)

1

3

4

1

63

110 110

EN

Installation instructions, for professionals only p. 13/32

4.4. Installation with foot (optional)

Observe Fig. 1, Fig. 5, Fig. 6 (page 10, 13, 14).

1. Attach the foot 1 using the screws enclosed 2 to the bottom of the heater.

Please note that the round recess is on the evaporator side.

2. Axthefootusingthescrewsenclosedtotheoor(Fig. 6). Depending

ontheoorconditions,usetheenclosedwoodscrewsoranchorswiththe

corresponding screws. Observe the minimum intervals for the heater shown

in Fig. 1.

WARNING!

Risk of re

●Affix the heater with the foot on a sufficiently solid substrate,

e.g. on the substrate onto which the sauna cabin is built – NOT on

theoorcoveringofthesauna.

Fig. 5 Installing the foot on the Concept R mini combi

2

1

Installation instructions, for professionals only p. 14/32

Fig. 6 Fixing the Concept R mini combi with foot in place

Fig. 7 Installing the wooden cover for the foot (optional)

Place the two halves of the cover ring around the foot and press them together

rmlytocoverthescrewsofthefoot.

L1 L2 N

L3 U

V

N

Wr

r

w

ϑϑ

U

V

NW

W

400V 3N~

NVNU

PE

N

V1

Wm

N

U1

WM

L2

L1

L3

4EN

Installation instructions, for professionals only p. 15/32

4.5. Connection diagram for 400V 3N~

Fig. 8

2

3

5

1

Connection diagram for the Concept R mini combi 3.5 kW, 4.5 kW,

6.0 kW and 7.5 kW

(CP-RMC-35 / CPC-RM-45 / CR-RMC-60 / CP-RMC-75)

Installation instructions, for professionals only p. 16/32

L1 L2 N

L3 U

V

N

Wr

r

w

ϑϑ

U

V

NW

W

230V 1N~

NVNU

L

PE

N

V1

Wm

N

U1

WM

4

4.6. Connection diagram for 230V 1N~

Fig. 9

2

3

5

1

Connection diagram for the Concept R mini combi 3.5 kW, 4.5 kW,

6.0 kW and 7.5 kW

(CP-RMC-35 / CPC-RM-45 / CR-RMC-60 / CP-RMC-75)

1 Sauna control unit

2 Temperature sensor with excess temperature cut-out

3 Evaporator 1.0 kW or 1.5 kW

4 Heating system 3.45 kW, 4.5 kW, 6.0 kW or 7.5 kW

5 Power supply

Remove the copper bridge

*

EN

Installation instructions, for professionals only p. 17/32

CP-RMC-35

3.5 kW

U V W N

1,15kW

N N

W V U

CP-RMC-60

6.0 kW

4.7. Wiring diagrams

CP-RMC-45

4.5 kW

U V W N

1,5kW

N N

W V U

U V W N

2,0kW

N N

W V U

to the control unit

U V W N

2,5kW

N N

W V U

to the control unit

CP-RMC-75

7.5 kW

U

V

W

N

PE

N

Installation instructions, for professionals only p. 18/32

4.8. Electrical connection

1. Unscrew the screws 3 with a screwdriver.

2. Remove the cover plates 1 and 2.

2

3

1

3

Connecting the Concept R mini combi 3.5 kW, 4.5 kW, 6.0 kW and 7.5 kW

(CP-RMC-35 / CP-RMC-45 / CR-RMC-60 / CP-RMC-75)

1. Guide the connection cable for the heating sys-

tem through the feed-through 4.

2. Connect the wires of the connection cable to

the matching terminals of the sauna heater,

depending on the type of connection, and to

the matching control device terminals. Observe

the installation instructions for the sauna control

and the connection diagrams on page 16.

Fig. 10 Removing the cover plates

4

EN

Installation instructions, for professionals only p. 19/32

3. Guide the evaporator cable through the feed-

through 5.

4. Connect the wires of the evaporator cable to the

PE – N – U1 – Wm terminals on the connector

block and to the matching sauna control unit

terminals. Observe the installation instructions

for the sauna control unit when doing so.

5. Re-attach the cover plates 1 and 2 to the

sauna heater or proceed with the installation of

the heater railing (optional).

ATTENTION!

Damage to the product

The product can be damaged by use of a cordless drill.

●Use a normal screwdriver to install the railing bracket.

A

B

5

4.9. Installing the heater railing (optional)

1. Remove the ceramic bowl from the evaporator.

2. Remove the cover plates 1 and 2 as described in 4.9 on page 18.

3. Unscrew the screws B and remove

cover frame A.

Installation instructions, for professionals only p. 20/32

4. Unscrew the screws C and install with

them the angle railing brackets D.

Depending on the preferred form of

the heater railing, you will need two

or four angle railing brackets.

5. Install the railing bracket E with

cover A using the previously re-

moved screws B.

6. Depending on requirements, you can put together the heater railing in

the shape of an L, U or O. To do this, use the wood screws provided.

C

A

D

F

H

G

I

K

L

E

B

Leht laadib ...

Sentiotec Concept R mini combi Kasutusjuhend

Sentiotec Concept R mini combi Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid