IPS122 Series
Installation and Operation Manual
X-PR-IPS122-eng
Part Number: 541B150AAG
December, 2017
Brooks
®
IPS122
2 Inch Stainless Steel
Indicating Pressure Switches
IPS122
2 Inch Stainless Steel
Indicating Pressure Switch
Installation and Operation Manual
X-PR-IPS122-eng
Part Number: 541B150AAG
December, 2017IPS122 Series
ESD (Electrostatic Discharge)
CAUTION: This instrument contains electronic components that are susceptible to damage by static electricity. Proper handling procedures must be observed
during the removal, installation or other handling of internal circuit boards or devices.
Handling Procedure:
1. Power to unit must be removed.
2. Personnel must be grounded, via a wrist strap or other safe, suitable means before any printed circuit card or other internal device is installed,
removed or adjusted.
3. Printed circuit cards must be transported in a conductive container. Boards must not be removed from protective enclosure until immediately before
installation. Removed boards must immediately be placed in protective container for transport, storage or return to factory.
Comments
This instrument is not unique in its content of ESD (electrostatic discharge) sensitive components. Most modern electronic designs contain components
that utilize metal oxide technology (NMOS, SMOS, etc.). Experience has proven that even small amounts of static electricity can damage or destroy these
devices. Damaged components, even though they appear to function properly, exhibit early failure.
Brooks Instrument designs, manufactures and tests its products to meet many national and international standards. These products must be properly
installed, operated and maintained to ensure they continue to operate within their normal specifications. The following instructions must be adhered to
and integrated into your safety program when installing, operating and maintaining Brooks Instrument products.
• To ensure proper performance, use qualified personnel to install, operate, update, program and maintain the product.
• Read all instructions prior to installing, operating and servicing the product. If this instruction manual is not the correct manual, please see back cover
for local sales office contact information. Save this instruction manual for future reference.
WARNING: Do not operate this instrument in excess of the specifications listed in the Instruction and Operation Manual. Failure to heed
this warning can result in serious personal injury and / or damage to the equipment.
• If you do not understand any of the instructions, contact your Brooks Instrument representative for clarification.
• Follow all warnings, cautions and instructions marked on and supplied with the product.
WARNING: Prior to installation ensure this instrument has the required approval ratings to meet local and national codes. Failure to heed this warning can
result in serious personal injury and / or damage to the equipment.
• Install your equipment as specified in the installation instructions of the appropriate instruction manual and per applicable local and national codes.
Connect all products to the proper electrical and pressure sources.
• Operation: (1) Slowly initiate flow into the system. Open process valves slowly to avoid flow surges. (2) Check for leaks around the flow meter inlet
and outlet connections. If no leaks are present, bring the system up to the operating pressure.
• Please make sure that the process line pressure is removed prior to service. When replacement parts are required, ensure that qualified people use
replacement parts specified by Brooks Instrument. Unauthorized parts and procedures can affect the product's performance and place the safe
operation of your process at risk. Look-alike substitutions may result in fire, electrical hazards or improper operation.
• Ensure that all equipment doors are closed and protective covers are in place to prevent electrical shock and personal injury, except when
maintenance is being performed by qualified persons.
WARNING: For liquid flow devices, if the inlet and outlet valves adjacent to the devices are to be closed for any reason, the devices must be completely
drained. Failure to do so may result in thermal expansion of the liquid that can rupture the device and may cause personal injury.
All pressure equipment with an internal pressure greater than 0.5 bar (g) and a size larger than 25mm or 1" (inch) falls under the Pressure Equipment Directive (PED).
• The Specifications Section of this manual contains instructions related to the PED directive.
• Products described in this manual are in compliance with EN directive 2014/34/EU.
• All Brooks Instrument Flowmeters fall under fluid group 1.
• Products larger than 25mm or 1" (inch) are in compliance with PED category I, II or III.
• Products of 25mm or 1" (inch) or smaller are Sound Engineering Practice (SEP).
The Brooks Instrument (electric/electronic) equipment bearing the CE mark has been successfully tested to the regulations of the Electro Magnetic
Compatibility (EMC directive 2014/30/EU).
Special attention however is required when selecting the signal cable to be used with CE marked equipment.
Quality of the signal cable, cable glands and connectors:
Brooks Instrument supplies high quality cable(s) which meets the specifications for CE certification.
If you provide your own signal cable you should use a cable which is overall completely screened with a 100% shield.
“D” or “Circular” type connectors used should be shielded with a metal shield. If applicable, metal cable glands must be used providing cable screen clamping.
The cable screen should be connected to the metal shell or gland and shielded at both ends over 360 Degrees.
The shield should be terminated to an earth ground.
Card Edge Connectors are standard non-metallic. The cables used must be screened with 100% shield to comply with CE certification.
The shield should be terminated to an earth ground.
For pin configuration : Please refer to the enclosed Instruction Manual.
European Pressure Equipment Directive (PED)
European Electromagnetic Compatibility (EMC)
Essential Instructions
Read before proceeding!
IPS122 Series
Installation and Operation Manual
X-PR-IPS122-eng
Part Number: 541B150AAG
December, 2017
Dear Customer,
We appreciate this opportunity to service your pressure measurement and control requirements with a Brooks
Instrument device. Every day, customers all over the world turn to Brooks Instrument for solutions to their gas and
liquid control applications. Brooks provides an array of flow, pressure and level measurement and control products
for various industries from biopharmaceuticals, oil and gas, fuel cell research and chemicals, to medical devices,
analytical instrumentation, semiconductor manufacturing, and more.
The Brooks product you have just received is of the highest quality available, offering superior performance,
reliability and value to the user. It is designed with the ever changing process conditions, accuracy requirements
and hostile process environments in mind to provide you with a lifetime of dependable service.
We recommend that you read this manual in its entirety. Should you require any additional information concerning
Brooks products and services, please contact your local Brooks Sales and Service Office listed on the back cover
of this manual or visit www.BrooksInstrument.com.
Yours sincerely,
Brooks Instrument
Installation and Operation Manual
X-PR-IPS122-eng
Part Number: 541B150AAG
December, 2017IPS122 Series
THIS PAGE WAS
INTENTIONALLY
LEFT BLANK
i
IPS122 Series
Installation and Operation Manual
X-PR-IPS122-eng
Part Number: 541B150AAG
December, 2017
Contents
Paragraph Page
Number Number
Section 1 General Information
1-1 Product Description....................................................................................................................... 1-1
1-2 Specifications ................................................................................................................................ 1-2
1-3 IPS122 Series Pressure Switch Dimensional Drawings................................................................ 1-3
Section 2 Product Description
2-1 General ......................................................................................................................................... 2-1
2-2 Receipt of Equipment.................................................................................................................... 2-1
2-3 Recommended Storage Practice .................................................................................................. 2-1
2-4 Return Shipment ...........................................................................................................................2-2
2-5 Transit Precautions ....................................................................................................................... 2-2
2-6 Removal from Storage ..................................................................................................................2-2
2-7 Gas Connections........................................................................................................................... 2-2
2-8 Installation ..................................................................................................................................... 2-3
2-9 Mounting .......................................................................................................................................2-3
2-10 Electrical Configuration ................................................................................................................. 2-3
2-11 Electrical Connections................................................................................................................... 2-4
2-12 Setpoint Adjustment ......................................................................................................................2-6
Section A Essential Instructions.............................................................................................................A-1
Warranty, Local Sales/Service Contact Information....................................................................... Back Cover
Figures
Figure Page
Number Number
1-1 IPS122 Dimensions.......................................................................................................................1-3
2-1 IPS122 Internal Jumper Settings .................................................................................................. 2-4
2-2 IPS122 Wiring Diagrams............................................................................................................... 2-5
2-3 0630149 Entity Drawing, Hazardous Location Applications, Indicating Pressure Switch .............. 2-6
2-4 0630150 Entity Drawing, Hazardous Location Applications, Indicating Pressure Switch .............. 2-7
ii
IPS122 Series
Installation and Operation Manual
X-PR-IPS122-eng
Part Number: 541B150AAG
December, 2017
Contents
THIS PAGE WAS
INTENTIONALLY
LEFT BLANK
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
IPS122 Series
1-1
Section 1 Introduction
1-1 Product Description
The Brooks IPS122 Series Stainless Steel Indicating Pressure Switch
provides a high-purity, precision pressure gauge and electronic switch with an
adjustable pressure switch setpoint. This compact 2 inch unit has the ability to
operate lights or relays up to a maximum of 12 watts. Available in a variety of
pressure ranges and process connections. This device provides solid state
switching for cleanroom and hazardous applications.
Approved by Factory Mutual
• Intrinsically safe (Entity) for use in Class I, Division 1, Group A, B, C and D
indoor hazardous (classification) locations.
• Non-incendive for Class I, Division 2, Groups A, B, C and D indoor
hazardous (classification) locations.
This manual is organized into the following sections:
Section 1 - Introduction
Section 2 - Installation
Section A-Essential Instructions
Back Cover - Limited Warranty and Contacts
It is recommended that this manual be read in its entirety before attempting to
operate or repair the Model IPS122 Series.
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
1-2
Section 1 Introduction
IPS122 Series
1-2 Specifications
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
IPS122 Series
1-3
Section 1 Introduction
1-3 IPS122 Series Pressure Switch Dimensional Drawings
Figure 1-1 IPS122 Dimensions
2.28" [57.9 mm]
1.88" [47.8 mm]
2.20" [55.9 mm]
1.18" [30.1 mm]
2.28" [57.9 mm]
2.16" [54.9 mm]
1.89" [48.0 mm]
Cable Diameter: 0.23"
FRONT VIEW SIDE VIEW
1.95" [49.5 mm]
1.32" [33.6 mm
]1.32" [33.6 mm]1.32" [33.6 mm]
1.32" [33.6 mm]
VM
FACE SEAL MALE 1/4"
VSM
FACE SEAL
SWIVEL MALE 1 /4"
NPT
1/4"
VSF
FACE SEAL
SWIVEL FEMALE 1 /4"
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
1-4
Section 1 Introduction
IPS122 Series
THIS PAGE WAS
INTENTIONALLY
LEFT BLANK
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
IPS122 Series
2-1
Section 2 Installation
2-1 General
This section provides installation instructions for the Brooks
®
IPS122 Series
Indicating Pressure Switch devices . Refer to Section 1 of this manual for
dimensions and process connections.
2-2 Receipt of Equipment
When the equipment is received, the outside packing case should be
checked for damage incurred during shipment. If the packing case is
damaged, the local carrier should be notified at once regarding his liability. A
report should be submitted to the nearest Brooks Instrument location listed
on the Global Service Network page on our website: BrooksInstrument.com/
GlobalSupportCenters
Remove the envelope containing the packing list. Carefully remove the
instrument from the packing case. Make sure spare parts are not discarded with
the packing materials. Inspect for damaged or missing parts.
2-3 Recommended Storage Practice
If intermediate or long-term storage of equipment is required, it is
recommended that the equipment be stored in accordance with the following:
a. Within the original shipping container.
b. Ambient temperature 21°C (70°F) nominal, 79°C (175°F) maximum
-29°C (-20°F) minimum.
c. Relative humidity 45% nominal, 60% maximum, 25% minimum.
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
2-2
Section 2 Installation
IPS122 Series
2-4 Return Shipment
Prior to returning any instrument to the factory for any reason, visit our
website for instructions on how to obtain a Return Materials Authorization
Number (RMA #) and complete a Decontamination Statement to accompany
it: BrooksInstrument.com/Service. All instruments returned to Brooks also
require a Material Safety Data Sheet (MSDS) for the fluid(s) used in the
instrument. Failure to provide this information will delay processing of the
instrument.
Instrument must have been purged in accordance with the following:
2-5 Transit Precautions
To safeguard against damage during transit, transport the device to the
installation site in the same container used for transportation from the factory,
if circumstances permit.
2-6 Removal from Storage
Upon removal of the device from storage, a visual inspection should be
conducted to verify its "as-received" condition. If the device has been subject
to storage conditions in excess of those recommended (refer to "2-3
Recommended Storage Practice" on p. 2-1), it should be subjected to a
pneumatic pressure test in accordance with applicable vessel codes.
2-7 Gas Connections
Prior to installation, ensure that all piping is clean and free from obstructions.
Install piping in such a manner that permits easy access to the device if
removal becomes necessary.
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
IPS122 Series
2-3
Section 2 Installation
2-8 Installation
!
DO NOT twist the cable so that it turns inside the IPS housing.
This may cause permanant damage to the device.
CAUTION
!
Failure to follow these procedures may adversely affect the product’s perfor-
mance and could void the product warranty. Inspect but DO NOT unwrap any
parts until installation. Contact your Brooks representative with any problems.
In most cases, physical mounting, wiring to the power supply and control
circuit, and setting setpoint is all that is required to complete installation of the
IPS pressure switch as received from the factory. Refer to the tag on the back
of the IPS pressure switch for factory configuration of close on ascending or
close on descending pressure.
For some applications it may be necessary to invert operation of the LED
indicator and/or logic signal configuration to ascending or descending
operation, disassembly is required to change internal jumper switches.
2-9 Mounting
Mount the IPS pressure switch to the proper fitting in the piping arrangement
following standard piping procedures.
2-10 Electrical Configuration
The IPS pressure switch contains two internal “jumper switches” to invert
operating functions. Use needle nose pliers to change the switch jumpers.
(Refer to Figure 2-1)
• LED Indicator
A red LED (light emitting diode) indicates when the pressure setpoint is
reached. Its operation is controlled by jumper switch J1. Changing the
position of the internal jumper switch inverts the operation of the LED. For
example, the LED may be set to turn ON when pressure either rises
above or drops below the setpoint.
• Output Switch - Ascending/Descending Operation
The IPS electronic switch may be configured to Close (turn ON) when
pressure either rises above the setpoint (ascending), or drops below the
set-point. (descending). This operation is controlled by jumper switch J2.
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
2-4
Section 2 Installation
IPS122 Series
2-11 Electrical Connections
Refer to the appropriate wiring diagram for wiring connections to the IPS
pressure switch (Figure 2-2).
Refer to appropriate wiring diagram for hazardous locations (Figure 2-3 or
Figure 2-4).
Figure 2-1 IPS122 Internal Jumper Settings
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
IPS122 Series
2-5
Section 2 Installation
Figure 2-2 IPS122 Wiring Diagrams
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
2-6
Section 2 Installation
IPS122 Series
Figure 2-3 0630149 Entity Drawing, Hazardous Location Applications, Indicating Pressure Switch
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
IPS122 Series
2-7
Section 2 Installation
Figure 2-4 0630150 Entity Drawing, Hazardous Location Applications, Indicating Pressure Switch
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
2-8
Section 2 Installation
IPS122 Series
2-12 Setpoint Adjustment
NOTICE
Note: Moving the red-pointer does not change the setpoint.
It is merely a visual reminder of where setpoint was previously set.
Before operating the device, ensure all fluid connections have been
properly tightened and where applicable, all electrical connections
have been properly terminated.
WARNING
!
(Typical factory setting is at mid-scale.)
1. Connect the IPS pressure switch to a variable pressure source.
2. Apply pressure equal to the desired setpoint.
3. Slowly turn the setpoint adjustment screw (with a 1/8” or smaller
flathead screwdriver only) until the LED indicator on top of the IPS
pressure switch is activated. DO NOT OVERTIGHTEN.
(Refer to Figure 2-1 for adjustment screw location)
• CLOCKWISE to activate the electronic switch to increase pressure
setpoint.
• COUNTERCLOCKWISE to activate the electronic switch to decrease
pressure setpoint.
4.Change the applied pressure until the gauge is within the normal zone of
operating pressure.
5.Slowly continue to change the pressure and verify that the LED indicator
is activated at the desired setpoint.
6.Repeat pressure cycle to verify setting and readjust if necessary.
7.Adjust the red pointer mounted on the lens cover with a small
screwdriver to indicate the setpoint setting.
DO NOT attempt to adjust the red pointer by rotating the cover.
CAUTION
!
8.On a compound gauge, the zero is indicated by a range on the dial
rather than a setpoint.
9.Clean the non-metallic parts with a damp cloth to avoid electric discharge.
When adjusting the setpoint, DO NOT overtighten the setpoint
adjustment screw in either direction. This may cause permanant
damage to the device.
CAUTION
!
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
IPS122 Series
2-9
Section 2 Installation
No routine maintenance is required on this device.
If it becomes necessary to remove the device from the system
after exposure to toxic, pyrophoric, flammable or corrosive gas,
purge the device thoroughly with a dry inert gas such as Nitrogen
before disconnecting gas connections. Failure to correctly purge
the device could result in fire, explosion or death. Corrosion or
contamination of the device upon exposure to air may occur.
This instrument contains electronic components that are
susceptible to damage by static electricity. Proper handling
procedures must be observed during the removal, installation or
other handling of internal circuit boards or devices.
CAUTION
!
Installation and Operation Manual
X-PR-IPS122-eng
Part Number 541B150AAG
December, 2017
2-10
Section 2 Installation
IPS122 Series
THIS PAGE WAS
INTENTIONALLY
LEFT BLANK
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
teistes keeltes
- italiano: Brooks IPS122 Istruzioni per l'uso
- slovenčina: Brooks IPS122 Návod na používanie
- română: Brooks IPS122 Instrucțiuni de utilizare
