Tiandy TC-D2410-AW Kasutusjuhend

1

OUTDOOR SPEED BOME CAMERA

User’s Manual

Before attempting to connect or operate this product, please

read these instructions completely

MINI HIGH SPEED DOME CAMERA

2

Contents

Important Safety Instructions………………………………………3

Caution…………………………………………………………………………4

Introduction……………………………………………………………………5

Drawing………………………………………………………………7

Connection……………………………………………………………8

Installation ……………………….……………………………………9

ID code setting……………………………………………………... 10

Protocol setting………………………………...…………………… 11

Setting Baud Rate…………………………………………………………….12

Setting Protocol of zoom camera …..…………………………….. 12

Operation…………………………………………………….…….. . 13

Camera OSD menu…..………………………………………………16

Operation of zoom camera…………………………………….……17

The OSD menu setting………………………...………………..…20

B01 Protocol………………………………………………………..…..32

Debugging………………………………………………………………34

General Failure Analysis Table……………………………………….35

Routine maintenance……..……………………………………….…38

Specification……………………………………………………………39

AppendixⅠ………………………………………………………..……40

3

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, or other apparatus (including amplifiers) that produce

heat.

9. Do not defeat the safety purpose of the polarized or grounding type

plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being from being walked on or

pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a used,

caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13. Unplug this apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury from tip over.

14. Refer all servicing to qualified service personnel. Servicing is

4

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or been dropped.

5

CAUTION

To prevent damage which may result in fire or electric shock hazard,

do not expose this appliance to rain or moisture.

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions.

1) This device may not cause harmful interference, and

2) This device must accept any interference that may cause undesired

operation.

CAUTION:

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

Introduction

Function Description

High Speed Dome Camera is an all-in-one high-tech monitoring

product, which integrates high-definition color video camera,

universal gear change pan-tilt and multi-function decoder, CPU

processor. This product furthest reduces the processes of connection

an installation between system reliability. Also the video camera is

very easy to install and maintain, has many features, such as perfect

shape, legerity and convenience, simple operation and etc.

1. Integrate multi-function decoder

Built-in decoder consists of multi-protocol and communications

protocol. Communication serial baud rate is adjustable. Using the

simple finger-switch inside the Dome device, the products can be

compatible with kinds of systems and has very high commonality.。

2. Integrate full-view rotary station

6

Horizontal 360°unlimited continuous rotation and rotation rate can be

adjusted from 0.1 ~240°per second continuously（Manual speed）.

Vertical rotation range is 0~90°and rotation rate can

achieve0.1~90°/s.

3：Intelligent power-off memory operation

a. Design ideally ,Auto-flip to follow object。

b. Provides 128 preset points.

c. Provide setting of scanning track and select scanning track

function.

d. Four groups of scanning tracks: Every group of scanning track can

set Max. 16 preset positions. If camera self support OSD menu

function. It can open completely when using.

e. Integrate multiple camera protocol. Support Max.5 different Brands

cameras.

f. Integrate multiple protocols: Max. 20 kinds of communication

protocol. Transmission rate Selectable from 1200bps to 38400bps

g. Self-test can allow to store track that user edits arbitrarily and

information power-off memory.

h. RS485 serial control, address of Dome device is from 1~255.

i. Built-in surge and lightning strike protective equipment.

7

DRAWING

8

CONNECTIONS

Precautions

• The following connections should be made by qualified service personnel

or system installers in accordance with all local codes.

1、 Before installing please read the instructions, of the unknown, please

contact seller.

2、 Connections (Figure)

Green RS485+ RS485 data

Yellow RS485-

Yellow & Green (Earth lead)

Blue AC Power

Brown AC Power

BNC Video output

Note: When powered up, the dome device performs a self-check (including one

panning, tilting, zooming and focusing operation).

If control wire of RS485 connects by the connective box, it can connect

as RS485A+ with blue wire, RS485B- with yellow wire.

9

Installation

1. On shield of protection, is trying to gain and installation to avoid scratches

spherical transparent and clean.

2. Choose the appropriate installation method. Speed dome camera must be

installed at the scaffold on a stable and reliable, the installation should be in

accordance with the requirements of surveillance scenes to make the largest screen

monitor, and monitor the clearest images.

3. Choose the best installation location, if possible to be able to minimize sun,

rain, avoid dust. Speed dome camera must be the work of the warming, we should

try to avoid the scorching sun exposure, and bear in mind indoor speed dome

camera can not be used outdoors.

4. Power supply should be selected with high-speed dome camera matching

power to ensure the normal operation of the speed dome camera and long-term

stability. Line voltage power supply to consider wear and tear, a sufficient number of

current job

5. Auxiliary equipment. As the project was also asked to consider applications

environmental conditions, such as at night to clear the recorded image, then on the

need to increase the environmental illumination.

6. Avoid interference. Communications and video signal cables have to be

asked to avoid electromagnetic interference, such as power transformers,

high-power electric motors or generators, high voltage generator, pulse generator

and other facilities, and these two signal lines have to wear steel pipe laying, and

strong Level voltage electric lines, with the regulatory requirements to maintain

spacing.

10

ID CODE SETTING

The ID code setting set by 8 digital-switch, address of speed dome

camera is from 1~255, about the Stir code of addresses 1~128, pls see

the Appendix Ⅰ.

There are the parts of Stir code of addresses .Setting as below picture

(Other, please turn on and so forth in accordance with the binary)：

Note: Black pane is the position of the key .Please power- off

before setting.

11

NOTE: If the Control Wire parallel connection many speed dome camera

the forest dome camera ,you should connect JM1 which is in RS485

interface of main control board .If the distance is very far ,you also

should do as above operation .Detail connect ,according to white line on

the main control board.

Connect JM1 which is in

RS485 interface of main

control board.

PROTOCOL SETTING

Protocol of this speed dome could transfer and freedom option

by the six key switches section 1, 2 and 3. Below is the detail of

setting protocol:

Commonly used baud rate (bps)：Pelco P/4800/9600；Pelco D/2400.

12

Setting Baud Rate of Dome Camera

Set baud rate of this speed dome camera by the six key switches

section 4 and 5 to select. Set as following:

SETTING PROTOCOL OF ZOOM CAMERA

Set zoom camera’s protocol of this speed dome camera by six of the last

switch. Setting as following:

13

OPERATION (Default protocol PELCO-D/2400)

The speed dome camera can be controlled remotely horizontal and vertical

movement. It is used with a system controller, separately. It is controlled remotely

from the controller through a serial connection to the RS-485 connector using a

twisted-pair cable.

Conventional Function

1. Pan / Tilt Function

The pan function will move the camera on all horizontal plane, to surveillance

position. The tilt function will move the camera on a vertical plane, to surveillance

position. The speed is variable according to the angle of joystick.

UP

LEFT RIGHT

DOWN

2. Zoom Function

2.1 The filming range can be set using the zoom function.

Press TELE the LCD displays Zoom Tele

Press WIDE the LCD displays Zoom Wide

Note： The bigger zoom is，the slower of joystick ‘s speed is .

2.2 Iris Function

Normally，Focus is AUTO。

Focus level can be adjusted by pressing [NEAR] and [FAR]

Move the joystick, focus will be auto.

3. Preset Memory

14

The preset memory function will memories camera positions and zoom, focus, etc.

Setting up to 128 preset camera positions can be memorized. Later, you can easily

recall any of the preset camera positions by entering its corresponding number, and

the camera will move the memorized position with all the preset settings.

3.1 To set a preset position

SET + N + ENTER

N: the number of preset position: 1~128

3.2 To call a preset position

When camera positions have been set, you can enter a memorized camera position

number.

Preset + N + ENTER

N: the number of preset position: 1~128

4. Delete a preset position

[PRESET]+ [N] + [OFF]

N: the number of preset position: 1~128

5. To call cruise tracks：

[PRESET]+32+[ENTER]

This command can call the No.1cruise tracks. It can scan preset points no.1 ~ 16.

[PRESET]+53+ [ENTER]

This command can call the No.2cruise tracks. It can scan preset points no.17 ~ 31.

[PRESET]+49+ [ENTER]

This command can call the No.3cruise tracks. It can scan preset points no.33 ~ 48.

[PRESET]+50+ [ENTER]

This command can call the No.1cruise tracks. It can scan preset points no.65 ~ 80.

Note: If some points are not been set or delete, it will not scanning these points

when cruising. Resort 3 seconds in every preset point.

6．Setting scanning track

Method 1：

1. Setting begin scanning track point

[SET] + [51] + [ENTER]

15

Adjust the position of dome camera which you need.

Setting finish scanning track point：

[SET] + [52] + [ENTER]

Adjust the position of dome camera which you need.

3． Calling scanning：

[PRESET]+51+ [ENTER]

Note: Setting begins and finishes scanning track point first.

4． Stop scanning

[PRESET]+52+ [ENTER]

(Move Joystick also can stop scanning）

When dome device scanning, default state following

a. Dome device scan between two points.

b. Scan “begin-point” and “end-point” and resort 3 seconds

c. If “begin-point” and “end-point” superpose, dome device horizontal 360°rotation.

Method 2：

Call scanning

[AUTO]+ [ON]

The speed dome camera scanning360 degree. Need not set

scanning track point.

Note: Above operation use for our company’s suited keyboard by

example, detail operation do as your keyboard menu

16

Camera OSD menu

Show Menu on display and setting other parameter of

zoom camera. Operation as follow:

Call No.57 preset position { [PRESET]+57+[ENTER]} to show

the main menu on display, and use [TELE]、[WIDE] to choose

item, then press [FAR]、[NEAR] to set and confirm .If you want

to set other items, you should come back main menu first. You

can choose [EXIT] item, then press [FAR] 、[NEAR] to

confirm .After these you will come back main menu.

Note：After setting item parameter, must set No.57 preset

position {[SET]+57+[ENTER]} to set free the key of menu. If

some camera can’t be controlled by [FAR] and[NEAR].You can

use [OPEN] to come true operation

Note: Here in before operation use for our company’s suited

keyboard by example, detail operation do as keyboard menu

17

Operation of camera

Note： Some cameras don’t support the above function of them.

Power-off memory

Provide setting of scanning track and select scanning track function. Self-test can

allow to store track that user edits arbitrarily and information power-off memory.

(N)

Control object

The definition of key

PRESET+N+ENTER

SET+N+ENTER

54

Power supply

Come back Initial value

/

55

Backlight

compensation

ON

OFF

56

Min. illumination

ON

OFF

57

Menu/ Screen Display

ON

OFF

58

Digital Zoom

ON

OFF

59

Focus

AUTO

MANUAL

60

IRIS

AUTO

MANUAL

61

White Balance

AUTO

MANUAL

62

Static image

Image congeal

Normal image

63

Mirror image

Image mirror

Normal image

64

Color/black & white

Color

B/W

18

Index Diagram of the Screen Menu

19

Index Diagram of the Screen Menu

This is the camera’s OSD function, which include the menu while

opening and the menu while operating.

Open it, and see the start of image, the order of showing is:

Waiting for image

The image of system information

The information of checking itself

The finished information of checking itself

Horizontal Check OK

Vertical Check OK

Camera Check OK

Waiting…

Version : 1.02

Camera : Sony

Dome ID : 001

Protocol : PelcoD

Band Rate : 2400

Self test passed, you

can control the Dome

now

20

The Menu Setting

● The major menu setting

After checking itself, please {[PRESET] +8+ [ENTER]}, then it

will show the image as the No.1-0-1:

→（Pic.1-1-1）

→（Pic.1-2-1）

→（Pic.1-3-1）

→（Pic.1-4-1）

→（Pic.1-5-1）

1-0-1 System information

On the menu of 1-0-1, turn up or down the rocker to point to system info

( or click the up or down key of controlling system) , then turn right to

enter to system info( or click the right key of control system)

As per the image 1-1-1:

Pic.1-1-1

The last pages all show the system setting; the consumer can’t operate

any item of setting the function of system.

● Camera function setting

On the image 1-0-1, turn up or down the rocker to point to the camera

System Info

System Setup

Camera Control

Preset Control

Special Function

Factory Default

EXIT

Version : 1.02

Camera : Sony

Dome ID : 001

Protocol : PelcoD

Baud Rate: 2400

EXIT

Leht laadib ...

Tiandy TC-D2410-AW Kasutusjuhend

Tiandy TC-D2410-AW Kasutusjuhend

teistes keeltes

Muud dokumendid