Dremel 4200 spetsifikatsioon

Bränd: Dremel

Mudel: 4200

Kategooria: Elektrilised tööriistad

Tüüp: spetsifikatsioon

WEU

Original instructions 14

Übersetzung der Originalbedienungsanleitung 18

Traduction de la notice originale 23

Traduzione delle istruzioni originali 29

Vertaling van de originele gebruiksaanwijzing 34

Oversættelse af betjeningsvejledning 39

Översättning av originalinstruktioner 44

Oversettelse av originalinstruksjonene 49

Käännös alkuperäisistä ohjeista 53

Algsete juhiste tõlge 58

Originalių instrukcijų vertimas 63

Oriģinālās lietošanas pamācības tulkojums 68

6 7

8 9

Figure 10: EZ SpeedClic

Figure 11: Attachment 225

Figure 12: Attachment 576 / 577

565

566

Figure 13: Attachment 565 / 566

568

Figure 14: Attachment 568

678

Figure 15: Attachment 678

575

Figure 16: Attachment 575

550

Figure 17: Attachment 550

CE DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in conformity with the following

standards or standardized documents: EN60745, EN55014, in accordance with the provisions

of the directives 2006/95/EC, 2004/108/EC, 2006/42/EC.

NOISE/VIBRATION

Measured in accordance with EN60745 the sound pressure level of this tool is 74.4 dB(A) and

the sound power level 85.4 dB(A) (standard deviation: 3 dB), and the vibration 18.0 ± 3.3 m/

s2 (hand-arm method). The declared vibration total value is measured in accordance with a

standard test method and may be used for comparing one tool with another. It may also be

used in a preliminary assessment of exposure.

Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

The vibration emission during use of the power tool can differ from the

declared values, depending on the ways you use the tool. Estimate the exposure in the actual

conditions of use and identify the safety measures for personal protection accordingly (taking

account of all parts of the operating cycle such as the times when the tool is switched off and

when it is running idle in addition to the trigger time).

EG-Konformitätserklärung

Wir erklären in alleiniger Verantwortung, dass dieses Produkt den folgenden Standards und

standardisierten Dokumenten entspricht: EN60745, EN55014, gemäß den Bestimmungen der

Richtlinien 2006/95/EG, 2004/108/EG, 2006/42/EG.

GERÄUSCHE/VIBRATIONEN

Gemessen gemäß EN60745 beträgt der Schalldruckpegel dieses Gerätes 74.4 dB(A) und

der Schalleistungspegel 85.4 dB(A) (Standardabweichung: 3 dB) und die Vibration 18.0 ±

3.3 m/s² (Hand-Arm Methode). Der angegebene Vibrationsgesamtwert wurde entsprechend

einer Standard-Testmethode gemessen und kann zum Vergleich von Werkzeugen verwendet

werden. Er kann auch zur vorläufigen Einschätzung der Exposition genutzt werden.

Technische Unterlagen erhalten Sie bei: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda,

NL.

Die Schwingungsemissionen hängen von der Art der Verwendung

des Werkzeugs ab und können von den angegebenen Werten abweichen. Um die Exposition

unter den tatsächlich Anwendungsbedingungen abzuschätzen und zu bestimmen, welche

persönlichen Schutzmaßnahmen erforderlich sind, sollten zusätzlich zu den Bedienungszeiten

auch die Zeiten berücksichtigt werden, in denen das Gerät abgeschaltet ist oder im Leerlauf

läuft.

Déclaration de conformité CE

Nous déclarons, sous notre propre responsabilité, que se produit est conforme aux normes ou

aux documents normalisés suivants : EN60745, EN55014, conformément aux dispositions des

directives 2006/95/EC, 2004/108/EC, 2006/42/EC.

BRUIT/VIBRATION

Mesuré conformément à la norme EN60745, le niveau de pression sonore de cet outil est de

74.4 dB(A), tandis que son niveau de puissance sonore est de 85.4 dB(A) (écart-type : 3 dB).

Les vibrations sont de 18.0 ± 3.3 m/s2 (méthode de la maladie des vibrations). La valeur

totale de vibration déclarée est mesurée selon une méthode de test standard, permettant

de comparer les outils entre eux. Elle peut également être utilisée dans une évaluation

préliminaire d'exposition.

Fiche technique disponible auprès de: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda,

NL.

L'émission de vibrations lors de l'utilisation de l'outil électroportatif peut

différer des valeurs déclarées selon la manière dont vous l'utilisez. Estimez l'exposition à ces

dernières dans les conditions réelles d'utilisation, qui vous permettra d'identifier les mesures

de sécurité à prendre en matière de protection personnelle (en tenant compte de l'ensemble

des parties du cycle d'exploitation, telles que le moment où l'outil est éteint et celui où il est en

veille, en plus de celui où il est activé).

Dichiarazione di conformità CE

Dichiariamo sotto la nostra esclusiva responsabilità che questo prodotto è conforme ai

seguenti standard o documenti standardizzati: EN60745, EN55014, secondo le disposizioni

previste dalle direttive 2006/95/CE, 2004/108/CE, 2006/42/CE.

RUMORE/VIBRAZIONI

Da misurazioni condotte secondo la norma EN60745, il livello di pressione sonora risulta di

74.4 dB(A) e il livello di pressione sonora 85.4 dB(A) (deviazione standard: 3 dB), mentre

le vibrazioni sono pari a 18.0 ± 3.3 m/s2 (sistema mano-braccio). Il valore totale dichiarato

delle vibrazioni è misurato secondo un metodo di prova standard e può essere utilizzato per

confrontare un utensile con un altro. Potrebbe essere utilizzato anche in una valutazione

preliminare dell'esposizione.

Documentazione tecnica presso: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

L'emissione di vibrazioni durante l'impiego dell'elettroutensile può

differire rispetto ai valori dichiarati, in base al modo con cui si utilizza l'utensile stesso.

Effettuare una stima dell'esposizione nelle condizioni di utilizzo effettive e individuare le

conseguenti misure di sicurezza per la protezione personale (tenendo conto di tutti gli elementi

del ciclo di funzionamento, ad esempio le volte in cui l'utensile viene spento e quando funziona

in folle oltre al tempo di attivazione).

CE-conformiteitsverklaring

Wij verklaren onder eigen verantwoordelijkheid dat dit product voldoet aan de volgende

normen of normatieve documenten: EN60745, EN55014, overeenkomstig de bepalingen van

de richtlijnen 2006/95/EG, 2004/108/EG, 2006/42/EG.

GELUID/TRILLINGEN

Gemeten volgens EN60745 bedraagt het geluidsdrukniveau van dit gereedschap 74.4 dB(A)

en het geluidsvermogenniveau 85.4 dB(A) (standaardafwijking: 3 dB). De trilling bedraagt 18.0

± 3.3 m/s2 (hand-arm-methode). Het opgegeven totale trillingsniveau is gemeten volgens een

standaard testmethode en kan worden gebruikt om een gereedschap te vergelijken met een

ander. Het kan ook worden gebruikt als preliminaire evaluatie van de blootstelling hieraan.

Technisch dossier bij: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, Nederland.

De trillingsemissie tijdens het daadwerkelijke gebruik van het

gereedschap kan afwijken van de opgegeven waarden. Dit is afhankelijk van de manier

waarop u het gereedschap gebruikt. Maak een inschatting van de mate waarin u tijdens

daadwerkelijk gebruik aan trillingen wordt blootgesteld en stel aan de hand hiervan de

persoonlijke beschermingsmaatregelen vast (waarbij u rekening houdt met alle onderdelen van

de bedrijfscyclus, waaronder de tijden dat het gereedschap is uitgeschakeld of is ingeschakeld

zonder dat het wordt gebruikt, evenals de blootstellingstijd).

CE overensstemmelseserklæring

Vi erklærer under eneansvar, at dette produkt er i overensstemmelse med følgende

normer eller standardiserede dokumenter: EN60745, EN55014, i overensstemmelse med

bestemmelserne i direktiverne 2006/95/EF, 2004/108/EF og 2006/42/EF.

STØJ/VIBRATION

Målt i overensstemmelse med EN60745 er dette værktøjs lydtrykniveau 74.4 dB (A) og

lydeffektniveau 85.4 dB (A) (standardafvigelse: 3 dB), og vibrationen 18.0 ± 3.3 m/s2

(hånd-arm-metoden). Den opgivede samlede måleværdi for vibrationen er målt i henhold

til en standardiseret målemetode. Denne målemetode kan bruges til at sammenligne

forskellige værktøjer med hinanden. Den kan også anvendes som en foreløbig vurdering af

eksponeringen.

Teknisk fil hos: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

Under brugen af el-værktøjet kan vibrationsemissionen afvige fra den

angivne værdi, afhængigt af hvordan værktøjet bruges. Vurder eksponeringen i de omgivelser,

hvor værktøjet skal bruges, og sørg derefter for de nødvendige sikkerhedsforanstaltninger

(alle aspekter af arbejdsforløbet skal indgå i vurderingen, også de perioder, hvor værktøjet er

slukket eller kører i tomgang).

CE-överensstämmelsedeklaration

Vi deklarerar härmed att denna produkt uppfyller villkoren i följande standarder eller

standardiserade dokument: EN60745, EN55014, i enlighet med direktiv 2006/95/EG,

2004/108/EG och 2006/42/EG.

BULLER/VIBRATION

Uppmätt i enlighet med EN60745: ljudtrycket för detta verktyg är 74.4 dB(A) och ljudnivån

är 85.4 dB(A) (standardavvikelse: 3 dB) och vibrationen 18.0 ± 3.3 m/s2 (metod: hand-

arm). Det angivna totala vibrationsvärdet mäts i enlighet med en standardtestmetod och får

användas för att jämföra ett verktyg med ett annat. Det kan även används vid en preliminär

exponeringsbedömning.

Teknisk fil på: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, Nederländerna.

Beroende på hur verktyget används kan vibrationerna vid användning

av verktyget skilja sig från de angivna värdena. Gör en uppskattning av exponeringen under

verkliga användningsförhållanden och vidta skyddsåtgärder för personalen därefter (ta hänsyn

till alla delar i användningsförloppet, som när verktyget stängs av och utöver starttiden, när det

går på tomgång).

CE-konformitetserklæring

Vi erklærer med eneansvar at dette produktet overholder følgende standarder eller

standardiserte dokumenter: EN60745, EN55014, i henhold til bestemmelsene i direktivene

2006/95/EF, 2004/108/EF og 2006/42/EF.

STØY/VIBRASJON

Lydtrykknivået til dette verktøyet, målt i henhold til EN60745, er 74.4 dB(A), og lydkraftnivået

er 85.4 dB(A) (standardavvik: 3 dB), og vibrasjon 18.0 ± 3.3 m/s2 (hånd-arm-metode).

Den erklærte totalverdien for vibrasjon er målt i henhold til en standardtestmetode, og kan

brukes til å sammenligne et verktøy med et annet. Den kan også brukes til innledende

eksponeringsvurdering.

Teknisk fil finnes hos: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, Nederland.

Vibrasjonsutstrålingen under faktisk bruk av elektroverktøyet kan

avvike fra de oppgitte verdiene, avhengig av måten verktøyet brukes på. Anslå eksponeringen

ved de faktiske bruksforhold, og fastsett sikkerhetstiltak for personlig beskyttelse i henhold til

dette (ta hensyn til alle deler av driftssyklusen, som for eksempel tidspunktene når verktøyet er

slått av og når det går på tomgang i henhold til utløsertiden).

Skil Europe B.V.: M. v.d. Hoofden, O. Dijkgraaf

CE-vaatimustenmukaisuusvakuutus

Vakuutamme, että tämä tuote täyttää seuraavien standardien tai standardiasiakirjojen

vaatimukset: EN60745, EN55014 ja direktiivien 2006/95/EY, 2004/108/EY ja 2006/42/EY

säännökset.

MELU/TÄRINÄ

EN60745-standardin mukaisesti mitattu työkalun äänenpainetaso on 74.4 dB(A), äänitehotaso

on 85.4 dB(A) (standardipoikkeama: 3 dB) ja tärinätaso on 18.0 ± 3.3 m/s2 (käteen ja

käsivarteen kohdistuva tärinä). Ilmoitettu tärinän kokonaisarvo on mitattu standardisoidun

testausmenetelmän mukaan ja kokonaisarvon avulla voidaan verrata työkaluja toisiinsa. Sitä

voidaan käyttää myös alustavaan altistusarviointiin.

Tekninen asiakirja osoitteessa: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda,

Alankomaat.

Tärinä sähkötyökalun käytön aikana voi poiketa ilmoitetuista arvoista

sen mukaan, miten työkalua käytetään. Arvioi altistus todellisissa käyttöoloissa ja tunnista sen

mukaiset tarvittavat toimet henkilökohtaista suojausta varten (ottaen huomioon varsinaisen

käytön lisäksi kaikki muutkin käyttösyklin osat, kuten ajat, jolloin työkalu on sammutettu tai

vapaalla).

EÜ vastavusavaldus

Avaldame, et vastutame ainuüksi selle eest, et toode vastab järgmistele standarditele või

standarditud dokumentidele: EN60745, EN55014 vastavalt direktiivide 2006/95/EÜ, 2004/108/

EÜ, 2006/42/EÜ sätetele.

MÜRA/VIBRATSIOON

Mõõdetakse vastavalt standardile EN60745, tööriista helirõhu tase on 74.4 dB(A) ja

helivõimsuse tase 85.4 dB(A) (standardhälve: 3 dB) ja vibratsioon 18.0 ± 3.3 m/s2

(kohtvibratsiooni meetod). Vibratsiooni deklareeritud koguväärtust mõõdetakse vastavalt

standardsele katsemeetodile ja seda võib kasutada ühe tööriista võrdlemisel teisega. Seda

võib kasutada ka kokkupuute eelhindamisel.

Tehnilise dokumendi asukoht. SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

Vibratsiooni emissioon elektrilise tööriista kasutamisel võib erineda

deklareeritud väärtusest, olenevalt sellest, millisel viisil tööriista kasutatakse. Hinnake

ligikaudselt vibratsiooniga kokkupuute aega tegelikes kasutustingimustes ja määrake kindlaks

sobivad ohutusmeetmed isiklikuks kaitseks (võttes arvesse kõiki töötsükli etappe nagu nt aega,

mil tööriist on välja lülitatud ja aega, mil see töötab tühjalt lisaks käivitusajale).

CE atitikties deklaracija

Prisiimdami visą atsakomybę pareiškiame, kad šis produktas atitinka toliau nurodomus

standartus arba standartizuotuosius dokumentus: EN60745, EN55014, pagal direktyvų

2006/95/EB, 2004/108/EB, 2006/42/EB nuostatas.

TRIUKŠMAS IR VIBRACIJA

Šio įrankio keliamo garso slėgio lygis, išmatuotas pagal EN60745, yra 74.4 dB(A), garso

galios lygis – 85.4 dB(A) (standartinis nuokrypis – 3 dB), o vibracija – 18.0 ± 3.3 m/s2 (rankos

pagreičio matavimo metodas). Deklaruojamoji suminė vibracijos vertė išmatuota standartiniu

bandymų metodu, todėl ja galima remtis lyginant vieną įrankį su kitu. Ja taip pat galima

naudotis atliekant preliminarųjį poveikio vertinimą.

Techninė byla laikoma adresu: „SKIL Europe BV“ (PT-SEU/PJE), 4825 BD Breda, NL.

Vibracija, susidaranti naudojant elektrinį įrankį, gali skirtis nuo

deklaruojamų verčių priklausomai nuo to, kokiu būdu naudojate įrankį. Įvertinkite poveikį

tikrosiomis naudojimo sąlygomis ir parinkite atitinkamas asmens apsaugos priemones

(atsižvelkite į visus darbo ciklo etapus, t. y. ne tik į trukmę, kai įrankis paleistas, bet ir laiką, kai

jis išjungiamas ir veikia tuščiąja eiga).

Deklarācija par atbilstību CE normām

Mēs, uzņemoties pilnu atbildību, paziņojam, ka šis izstrādājums atbilst zemāk minētajiem

standartiem vai standartizētajiem dokumentiem: EN60745, EN55014, saskaņā ar attiecīgo

direktīvu normatīviem 2006/95/EC, 2004/108/EC, 2006/42/EC.

TROKSNIS/VIBRĀCIJA

Mērīts saskaņā ar EN60745 šī instrumenta skaņas spiediena līmenis ir 74.4 dB(A) un

skaņas jaudas līmenis ir 85.4 dB(A) (standartnovirze: 3 dB), un vibrācija 18.0 ± 3.3 m/s2

(plaukstas-rokas metode). Minētā vibrācijas kopējā vērtība ir mērīta saskaņā ar standarta

testēšanas metodi un var tikt lietota, lai salīdzinātu vienu instrumentu ar citu. To var izmantot

arī iepriekšējai iedarbības novērtēšanai.

Tehniska rakstura fails: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL.

Elektriskā instrumenta lietošanas laikā sasniegtā vibrācijas emisijas

vērtība var atšķirties no norādītās kopējās vērtības atkarībā no instrumenta izmantošanas

veida. Nosakiet instrumenta radīto iedarbību faktiskajos izmantošanas apstākļos un izvēlieties

attiecīgus drošības pasākumus personiskai aizsardzībai (ņemot vērā visus darba cikla

faktorus, piemēram, cik reižu instruments ir izslēgts un cik ilgi pēc ieslēgšanas tas darbojas

brīvgaitā).

CE





EN55014























 





ﺮـﻳﺬـﺤـﺗ

















ORIGINAL INSTRUCTIONS

INTRODUCTION

Thank you for purchasing the Dremel multitool that gives you an ultimate

performance when working on detailed and intricate tasks. This product

was designed for the many Dremel users who passionately use their

multitool daily and with their wishes and specifications in mind. You will

appreciate the many applications that this multitool can easily handle.

GENERAL DESCRIPTION

The Dremel multitool is a high quality precision tool that allows you to

perform a large variety of tasks. This multitool is intended to function as

a grinder, carver, engraver, sander, wire brush, cleaner/polisher or cut-off

tool. Refer to our online catalogue for the wide range of original Dremel

accessories and attachments you can use.

The Dremel 4200 is the FIRST multitool that easily changes accessories

without using a wrench. It uses a fully integrated lever mechanism

that clamps the accessory. In addition, this multitool is equipped with a

high performance motor with electronic feedback that allows the tool to

maintain its speed under load conditions. It also provides a "soft start",

which will reduce the stresses in case of a high torque start.

CONSTRUCTION

Refer to figure 1.

a. Housing cap

b. On/Off switch

c. Brush cover

d. Variable speed dial

e. Power cord

f. Hanger

g. Ventilation openings

h. EZ Change levers

i. EZ Change chuck

j. Collet

USED SYMBOLS

READ THESE INSTRUCTIONS

WARNING

USE HEARING PROTECTION

USE EYE PROTECTION

USE A DUST MASK

CLASS II CONSTRUCTED

GENERAL POWER TOOL SAFETY

WARNINGS

GENERAL

a. Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious

injury.

b. Save all warnings and instructions for future reference. The term

“power tool” in the warnings refers to your mains-operated (corded)

power tool or batery-operated (cordless) power tool.

WORK AREA SAFETY

a. Keep work area clean and well lit. Cluttered and dark areas invite

accidents.

b. Do not operate power tools in explosive atmospheres, such as in

the presence of flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

a. Power tool plug must match the outlet. Never modify the plug

in any way. Do not use any adapter plugs with earthed (grounded)

power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

b. Avoid body contact with earthed or grounded surfaces such as

pipes, radiators, ranges and refrigerators. There is an increased risk

of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling

or unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or tangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an extension cord

suitable for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use

an earth leakage circuit breaker (ELCB) protected supply. Use of an

earth leakage circuit breaker reduces the risk of electric shock.

PERSONAL SAFETY

a. Stay alert, watch what you are doing and use common sense

when operating a power tool. Do not use a power tool while you

are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious

personal injury.

b. Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-

position before connecting to power source and/ or battery pack,

picking up or carrying the tool. Carrying power tools with your finger

on the switch or energising power tools that have the switch on invites

accidents.

d. Remove any adjusting key or wrench before turning the power

tool on. A wrench or a key left attached to a rotating part of the power

tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times.

This enables better control of the power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your

hair, clothing and gloves away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of these devices can reduce dust related hazards.

POWER TOOL USE AND CARE

a. Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on

and off. Any power tool that cannot be controlled with the switch is

dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the battery

pack from the power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not

allow persons unfamiliar with the power tool or these instructions

to operate the power tool. Power tools are dangerous in the hands of

untrained users.

e. Maintain power tools. Check for misalignment or binding of

moving parts, breakage of parts and any other condition that may

affect the power tools operation. If damaged, have the power tool

repaired before use. Many accidents are caused by poorly maintained

power tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting

tools with sharp cutting edges are less likely to bind and are easier to

control.

g. Use the power tool, accessories and tool bits etc., in accordance

with these instructions, taking into account the working conditions

and the work to be performed. Use of the power tool for operations

different from those intended could result in a hazardous situation.

SERVICE

a. Have your power tool serviced by a qualified repair person using

only identical replacement parts. This will ensure that the safety of the

power tool is maintained.

MULTITOOL SAFETY WARNINGS

SAFETY WARNINGS COMMON FOR

GRINDING, SANDING, WIRE BRUSHING,

POLISHING, CARVING OR ABRASIVE CUTTING-

OFF OPERATIONS

a. This power tool is intended to function as a grinder, sander, wire

brush, polisher, carving or cut-off tool. Read all safety warnings,

instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in

electric shock, fire and/or serious injury.

b. Do not use accessories which are not specifically designed and

recommended by the tool manufacturer. Just because the accessory

can be attached to your power tool, it does not assure safe operation.

c. The rated speed of the grinding accessories must be at least

equal to the maximum speed marked on the power tool. Grinding

accessories running faster than their rated speed can break and fly

apart.

d. The outside diameter and the thickness of your accessory must

be within the capacity rating of your power tool. Incorrectly sized

accessories cannot be adequately controlled.

e. The arbour size of wheels, sanding drums or any other accessory

must properly fit the spindle or collet of the power tool. Accessories

that do not match the mounting hardware of the power tool will run out of

balance, vibrate excessively and may cause loss of control.

f. Mandrel mounted wheels, sanding drums, cutters or other

accessories must be fully inserted into the collet or chuck. If the

mandrel is insufficiently held and/or the overhang of the wheel is too

long, the mounted wheel may become loose and be ejected at high

velocity.

g. Do not use a damaged accessory. Before each use inspect the

accessory such as abrasive wheels for chips and cracks, sanding

drum for cracks, tear or excess wear, wire brush for loose or

cracked wires. If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After inspecting and

installing an accessory, position yourself and bystanders away

from the plane of the rotating accessory and run the power tool at

maximum no-load speed for one minute. Damaged accessories will

normally break apart during this test time.

h. Wear personal protective equipment. Depending on application,

use face shield, safety goggles or safety glasses. As appropriate,

wear dust mask, hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece fragments. The

eye protection must be capable of stopping flying debris generated by

various operations. The dust mask or respirator must be capable of

filtrating particles generated by your operation. Prolonged exposure to

high intensity noise may cause hearing loss.

i. Keep bystanders a safe distance away from work area. Anyone

entering the work area must wear personal protective equipment.

Fragments of workpiece or of a broken accessory may fly away and

cause injury beyond immediate area of operation.

j. Hold power tool by insulated gripping surfaces only, when

performing an operation where the cutting accessory may contact

hidden wiring or its own cord. Cutting accessory contacting a "live"

wire may make exposed metal parts of the power tool "live" and could

give the operator an electric shock.

k. Always hold the tool firmly in your hand(s) during the start-up.

The reaction torque of the motor, as it accelerates to full speed, can

cause the tool to twist.

l. Use clamps to support workpiece whenever practical. Never hold

a small workpiece in one hand and the tool in the other hand while

in use. Clamping a small workpiece allows you to use your hand(s) to

control the tool. Round material such as dowel rods, pipes or tubing have

a tendency to roll while being cut, and may cause the bit to bind or jump

toward you.

m. Position the cord clear of the spinning accessory. If you lose

control, the cord may be cut or snagged and your hand or arm may be

pulled into the spinning accessory.

n. Never lay the power tool down until the accessory has come to a

complete stop. The spinning accessory may grab the surface and pull

the power tool out of your control.

o. After changing the bits or making any adjustments, make sure

the collet nut, chuck or any other adjustment devices are securely

tightened. Loose adjustment devices can unexpectedly shift, causing

loss of control, loose rotating components will be violently thrown.

p. Do not run the power tool while carrying it at your side. Accidental

contact with the spinning accessory could snag your clothing, pulling the

accessory into your body.

q. Regularly clean the power tool's air vents. The motor's fan

will draw the dust inside the housing and excessive accumulation of

powdered metal may cause electrical hazards.

r. Do not operate the power tool near flammable materials. Sparks

could ignite these materials.

s. Do not use accessories that require liquid coolants. Using water

or other liquid coolants may result in electrocution or shock.

t. Use completely unrolled and safe extension cords with a capacity

of 5 Amps at least.

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or snagged rotating wheel,

sanding band, brush or any other accessory. Pinching or snagging

causes rapid stalling of the rotating accessory which in turn causes

the uncontrolled power tool to be forced in the direction opposite of the

accessory's rotation. For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may either jump toward or away

from the operator, depending on direction of the wheel's movement

at the point of pinching. Abrasive wheels may also break under these

conditions. Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by taking proper

precautions as given below.

a. Maintain a firm grip on the power tool and position your body and

arm to allow you to resist kickback forces. The operator can control

kickback forces, if proper precautions are taken.

b. Use special care when working corners, sharp edges etc. Avoid

bouncing and snagging the accessory. Corners, sharp edges or

bouncing have a tendency to snag the rotating accessory and cause loss

of control or kickback.

c. Do not attach a toothed saw blade. Such blades create frequent

kickback and loss of control.

d. Always feed the bit into the material in the same direction as

the cutting edge is exiting from the material (which is the same

direction as the chips are thrown). Feeding the tool in the wrong

direction causes the cutting edge of the bit to climb out of the work and

pull the tool in the direction of this feed.

e. When using rotary files, cut-off wheels, high-speed cutters or

tungsten carbide cutters, always have the work securely clamped.

These wheels will grab if they become slightly canted in the groove,

and can kickback. When a cut-off wheel grabs, the wheel itself usually

breaks. When a rotary file, high-speed cutter or tungsten carbide cutter

grabs, it may jump from the groove and you could lose control of the tool.

SAFETY WARNINGS SPECIFIC FOR

GRINDING AND ABRASIVE CUTTING-OFF

OPERATIONS

a. Use only wheel types that are recommended for your power tool

and only for recommended applications. For example: do not grind

with the side of a cut-off wheel. Abrasive cut-off wheels are intended

for peripheral grinding, side forces applied to these wheels may cause

them to shatter.

b. For threaded abrasive cones and plugs use only undamaged

wheel mandrels with an unrelieved shoulder flange that are of

correct size and length. Proper mandrels will reduce the possibility of

breakage.

c. Do not "jam" a cut-off wheel or apply excessive pressure. Do not

attempt to make an excessive depth of cut. Overstressing the wheel

increases the loading and susceptibility to twisting or snagging of the

wheel in the cut and the possibility of kickback or wheel breakage.

d. Do not position your hand in line with and behind the rotating

wheel. When the wheel, at the point of operation, is moving away from

your hand, the possible kickback may propel the spinning wheel and the

power tool directly at you.

e. When wheel is pinched, snagged or when interrupting a cut

for any reason, switch off the power tool and hold the power tool

motionless until the wheel comes to a complete stop. Never attempt

to remove the cut-off wheel from the cut while the wheel is in

motion otherwise kickback may occur. Investigate and take corrective

action to eliminate the cause of wheel pinching or snagging.

f. Do not restart the cutting operation in the workpiece. Let the

wheel reach full speed and carefully re-enter the cut. The wheel may

bind, walk up or kickback if the power tool is restarted in the workpiece.

g. Support panels or any oversized workpiece to minimize the risk

of wheel pinching and kickback. Large workpieces tend to sag under

their own weight. Supports must be placed under the workpiece near

the line of cut and near the edge of the workpiece on both sides of the

wheel.

h. Use extra caution when making a "pocket cut" into existing walls

or other blind areas. The protruding wheel may cut gas or water pipes,

electrical wiring or objects that can cause kickback.

SAFETY WARNINGS SPECIFIC FOR WIRE

BRUSHING OPERATIONS

a. Be aware that wire bristles are thrown by the brush even during

ordinary operation. Do not overstress the wires by applying

excessive load to the brush. The wire bristles can easily penetrate light

clothing and/or skin.

b. Allow brushes to run at operating speed for at least one minute

before using them. During this time no one is to stand in front or in

line with the brush. Loose bristles or wires will be discharged during the

run-in time.

c. Direct the discharge of the spinning wire brush away from you.

Small particles and tiny wire fragments may be discharged at high

velocity during the use of these brushes and may become imbedded in

your skin.

PREPARATION

Always unplug the tool from the power source before you make

any adjustments, change accessories, service, clean, etc. This

reduces the risk of starting the tool accidentally.

FIRST USE

The carbon brushes in your tool have been engineered for many hours

of dependable service. To prepare the brushes for use, run the tool at full

speed for 5 minutes under no load. This will properly "seat" the brushes,

and extend the life of the tool.

CHANGING COLLETS

Four different size collets are available for your multitool, to

accommodate different shank sizes. Always use the collet which

matches the shank size of the accessory you plan to use. Never force a

larger diameter shank into a collet. Collet sizes can be identified by the

rings on the back end of the collet. Refer to figure 2.

• 3.2mm / 1/8" Collet with no rings

• 2.4mm / 3/32" Collet with three rings (not included)

• 1.6mm / 1/16" Collet with two rings (not included)

• 0.8mm / 1/32" Collet with one ring (not included)

Use 4200 specific collets only. You can order the collets through

the Dremel Service Center or go to www.dremel.com.

1. Remove a collet (J) from the EZ Change™ chuck (I). Refer to figure

3 and 4.

a. Use needle nose pliers to lightly depress the finger (L) of the

collet until it is clear of the detent feature (K).

b. Pull and hold both EZ Change™ levers to the back (unlock).

c. Pull the collet free from the chuck.

d. Release the EZ Change™ levers.

2. Install a new collet by inserting the narrow end of the new collet

completely into the EZ Change™ chuck.

The fingers (L) of the collet must be aligned with the detents (K)

of the EZ Change™ chuck to be fully inserted.

CHANGING ACCESSORIES

Your Dremel 4200 is equipped with the EZ Change™ mechanism. It

allows you to quickly and easily change accessories without the use of

a wrench.

Use only Dremel tested, high performance accessories! You can

order accessories through the Dremel Service Center or go to

www.dremel.com.

Use the EZ Speedclic to easily install and remove EZ SpeedClic

accessories. Refer to figure 10.

Do not operate the EZ Change™ levers while the multitool is

running as the bit may be ejected.

1. Remove an accessory. Refer to figure 5.

a. Pull and hold both EZ Change™ levers to the back (1) as far as

they will go.

b. Remove the accessory (2).

2. Install an accessory. Refer to figure 5.

a. Pull and hold both EZ Change™ levers to the back (1) as far as

they will go.

b. Insert the accessory into the collet as far as possible (2) to

minimize runout and unbalance.

c. Release the EZ Change™ levers (3).

d. Press the EZ Change™ levers to the front (lock) to fully secure

the bit.

Make sure the accessory is properly secured. Loose

accessories can unexpectedly shift or eject, causing loss of

control. Always use the collet which matches the shank size of

the accessory you plan to use.

If slipping of the accessory occurs, while in use, the tool needs

service.

e. Position yourself and bystanders away from the plane of the

rotating accessory and run the multitool at maximum no load

speed for one minute. Damaged accessories should break apart

during this test time.

You can tell by the sound and feel if your accessory is running

in balance. To true up or balance an accessory, slightly pull

back the EZ Change™ levers and give the accessory a 1/4 turn.

Release the levers and run the tool. Continue adjusting like this

until best balance is achieved.

USING ATTACHMENTS

Your Dremel 4200 can be equipped with different attachments that

expand the functionality of your tool.

Not all attachments listed below are included in your kit. Use

only Dremel tested, high performance attachments! You can

order attachments through the Dremel Service Center or go to

www.dremel.com for attachment and accessory compatibility.

1. Use the Flexible Shaft (225) for precise, detailed work or hard to

reach places. Refer to figure 11.

For optimum performance allow your new Flexshaft to run at

high speed on your multitool in a vertical position for 2 minutes

before use.

2. Use the Dremel Shaping Platform (576) to sand and grind at perfect

90 and 45 degree angles. Refer to figure 12.

3. Use the Dremel Detailer's Grip (577) to have even better control of

your Multitool. Refer to figure 12.

4. Use the Multipurpose Cutting Kit (565/566) for controlled cutting in a

variety of materials. Refer to figure 13.

5. Use the Wall & Floor Grout Removal Kit (568) for removing grout

from between wall and floor tiles. Refer to figure 14.

6. Use the Line & Circle Cutter (678) to make perfect holes and straight

cuts. Refer to figure 15.

7. Use the Right Angle Attachment (575) to use accessories in right

angle for hard to reach places. Refer to figure 16.

8. Use the Comfort Guard Attachment to protect you from dust and

sparks. Refer to figure 17.

OPERATION

Practice on scrap material first to see how the tool performs.

Your multitool performs best by allowing the tool, along with

the correct Dremel accessory, attachment and speed, to do

the work for you. Lower the spinning accessory gently to the

work surface and allow it to touch the point at which you want to

begin. Concentrate on guiding the tool over the work using very

little pressure. Increasing pressure on the tool is not the answer

when it is not performing properly. Try a different accessory or

speed setting to achieve the desired result.

Usually it is better to make a series of passes with the tool

rather than to do the entire job with one pass. A gentle touch

gives the best control and reduces the chance of error.

HOLDING THE TOOL

The design of the tool is symmetrical and contains plenty of soft grip. The

tool can be held comfortably in many positions.

Always hold the tool away from your face. Accessories can

damage during operation and can fly apart as they come up to

speed.

When you hold the tool, do not cover the ventilation openings

with your hand. Blocking the ventilation openings can cause the

motor to overheat.

1. Get the "feel" of the tool before using it by holding it in your hand and

feeling its weight and balance.

2. Grip the tool like a pencil between your thumb and forefinger for the

best control in close work. Refer to figure 6.

3. Use the "golf" grip for heavier operations such as grinding or cutting.

Refer to figure 7.

POWERING THE TOOL

The tool is turned "ON" and "OF" by the On/Off switch on the top side of

the motor housing.

1. Insert the power plug into the socket.

2. Turn the tool "ON" by sliding the On/Off switch forward.

3. Turn the tool "OFF" by sliding the On/Off switch backward.

Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may grab

the surface and pull the power tool out of your control.

SETTING THE RIGHT SPEED

Your tool is equipped with a variable speed dial. You can adjust the

speed during operation by pre-setting the dial on or between any one of

the settings.

Switch Setting Speed Range (/min) Qualification

5 5,000

10 10,000

15 15,000

Low speed

20 20,000

25 25,000

30 30,000

33 33,000

High speed

Refer to the Technical Specifications of the accessory (on-line

or on package) for the Maximum Speed. Do not use high speed

when using wire brushes. At high speed, wires can discharge

from the holder.

1. Use a low speed (15,000 /min or less) when:

a. Polishing, buffing and cleaning with a wire brush.

b. Polishing with felt polishing accessories.

c. Working with materials that can be damaged by high-

speed generated heat. Some materials burn or melt at low

temperatures.

2. Use higher speeds for hardwoods, metals and glass and for drilling,

carving, cutting, routing and shaping.

If a high speed steel cutter starts to vibrate, it usually indicates

that it is running too slow.

3. Aluminium, copper alloys, lead alloys, zinc alloys and tin may be cut

at various speeds, depending on the type of cutting.

Use a paraffin or other suitable lubricant (not water) on the

cutter to prevent the material from adhering to the cutter teeth.

MAINTENANCE AND REPAIR

Always unplug the tool from the power source before you make

any adjustments, change accessories, service, clean, etc. This

reduces the risk of starting the tool accidentally.

Have your power tool serviced by a qualified repair person who

uses only identical replacement parts. We recommend that all

tool service be performed by a Dremel Service Centre. This

will ensure the safety of the tool. Maintenance performed by

unauthorized personnel can result in incorrect connection of

internal wiring and components which can cause serious hazard.

You can only inspect and replace the carbon brushes. There are

no other serviceable parts inside the tool.

CLEANING

1. Clean ventilation openings, switch and levers of the tool with

compressed dry air.

Do not clean the tool by inserting pointed objects through an

opening.

Wear safety goggles to protect your eyes.

2. Clean the surface of the tool with a damp cloth.

Do not clean the tool with cleaning agents and solvents, such

as gasoline, carbon tetrachloride, chlorinated cleaning solvents,

ammonia and household detergents that contain ammonia. They

can cause damage to the plastic parts.

MAINTAINING THE CARBON BRUSHES

To maintain peak efficiency of the motor, inspect the brushes for wear

every 40-50 hours of use. Also inspect the brushes when the tool runs

erratically, loses power, or makes unusual noises.

Using the tool with worn brushes will permanently damage the

motor. Use only original Dremel replacement brushes.

1. Unplug the tool and place it on a clean surface.

2. Remove the two brush caps with the tool wrench as a screwdriver.

Refer to figure 8.

3. Remove the two brushes from the tool by pulling the springs that are

attached. Refer to figure 9.

4. Inspect both brushes. If a brush is less than 3mm long and/or the

surface of the brush is rough or pitted, replace the carbon brush by a

new one.

a. Remove the spring from the brush.

b. Throw away the old brush and place the spring on a new brush.

If one brush is worn, you should replace both brushes for better

performance of your tool.

5. Place the carbon brushes (with spring) back into the tool.

There is only one way the brush will fit back into the tool.

6. Replace the brush caps by turning the caps clockwise.

To tighten, use the wrench, but do not over tighten!

7. Refer to First use to start using the tool again.

SERVICE AND WARRANTY

NO USER SERVICEABLE PARTS INSIDE. This DREMEL product is

guaranteed in accordance with statutory/country-specific regulations.

Damage due to normal wear and tear, overload, improper handling

or lack of reasonable maintenance and care are excluded from the

warranty. In case of a complaint, send the undismantled tool or charger

and proof of purchase to your dealer.

CONTACT DREMEL

For more information on the Dremel product range, support and hotline,

go to www.dremel.com.

Dremel Europe, P.O. Box 3267, 4800 DG Breda, The Netherlands

ENVIRONMENT

DISPOSAL

The machine, accessories and packaging should be sorted for

environmental-friendly recycling.

ONLY FOR EC COUNTRIES

Do not dispose of power tools with household waste!

According the European Guideline 2002/96/EC for

Waste Electrical and Electronic Equipment and its

implementation into national law, power tools that are

no longer usable must be collected separately and

disposed of in an environmentally-correct manner.

GENERAL SPECIFICATIONS

Voltage Rating 230-240 V, 50-60 Hz

Related Power 175 W

Rated Speed (n) 33,000 /min

Collet Capacity 0.8 mm, 1.6 mm, 2.4 mm, 3.2 mm

Class II construction Double insulated construction

tools

ÜBERSETZUNG DER

ORIGINALBEDIENUNGSANLEITUNG

EINFÜHRUNG

Wir freuen uns, dass Sie sich für das Multifunktionswerkzeug von Dremel

entschieden haben – denn dieses Gerät bietet eine ultimative Leistung

für besonders feine und detaillierte Arbeiten. Bei der Entwicklung

wurden die Wünsche und Anforderungen der zahlreichen Dremel-

Nutzer berücksichtigt, die ihr Multifunktionswerkzeug täglich mit

großer Leidenschaft verwenden. Sie werden begeistert sein, wie viele

Anwendungen das Gerät problemlos meistert!

ALLGEMEINE BESCHREIBUNG

Das Multifunktionswerkzeug von Dremel ist ein hochpräzises Werkzeug

zur Durchführung von zahlreichen verschiedenen Anwendungen. Es

kann als Schleifer, Fräser, Gravierer, Sandpapierschleifer, Drahtbürste,

Reiniger/Polierer und Trennschleifmaschine verwendet werden. Eine

Übersicht über die vielen zugehörigen Original-Zubehörteile und -

Vorsatzgeräte von Dremel finden Sie in unserem Online-Katalog.

Der Dremel 4200 ist das erste Multifunktionswerkzeug, bei dem das

Zubehör ganz einfach ohne Spannzangenschlüssel aufgezogen

werden kann. Möglich macht dies ein integrierter Hebelmechanismus,

mit dem das Zubehör fixiert wird. Zudem ist das Gerät mit einem

Hochleistungsmotor mit elektronischer Drehzahlregelung ausgestattet,

das die Drehzahl bei erhöhter Belastung konstant hält. Darüber hinaus

bietet es einen „sanften“ Anlauf, der die Belastung bei einem Anlauf mit

großem Drehmoment verringert.

AUFBAU

Siehe Abbildung 1.

a. Gehäusekappe

b. Ein-/Aus-Schalter

c. Bürstenabdeckung

d. Drehzahlwahlschalter

e. Netzkabel

f. Aufhängevorrichtung

g. Lüftungsschlitze

h. EZ Change-Hebel

i. EZ Change-Futter

j. Spannzange

VERWENDETE SYMBOLE

LESEN SIE DIESE ANWEISUNGEN

WARNUNG

TRAGEN SIE GEHÖRSCHUTZ

TRAGEN SIE AUGENSCHUTZ

TRAGEN SIE EINE STAUBMASKE

KLASSE-II-AUSFÜHRUNG

Dremel 4200 spetsifikatsioon

Bränd: Dremel

Mudel: 4200

Kategooria: Elektrilised tööriistad

Tüüp: spetsifikatsioon

Laadige alla PDF

aruanne

teistes keeltes

italiano: Dremel 4200 specificazione
English: Dremel 4200 Specification

Dremel 4200 spetsifikatsioon

Dremel 4200 spetsifikatsioon

teistes keeltes

Seotud paberid

Muud dokumendid