Brooks 3809G / 3809G ELF / 3809G TFE Lined / 3810G Kasutusjuhend

Bränd: Brooks

Mudel: 3809G / 3809G ELF / 3809G TFE Lined / 3810G

Tüüp: Kasutusjuhend

See käsiraamat sobib ka

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Brooks

Models MT3809G and MT3810G

Metal Tube Variable Area Flowmeters

Model MT3809G, FNPT Connections,

General Purpose Stainless Steel Housing

Model MT3809G, Flanged Connections,

Explosion Proof Housing

Model MT3809G, Flanged Connections,

Intrinsically Safe Housing

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

ESD (Electrostatic Discharge)

CAUTION: This instrument contains electronic components that are susceptible to damage by static electricity. Proper handling procedures must be observed

during the removal, installation or other handling of internal circuit boards or devices.

Handling Procedure:

1. Power to unit must be removed.

2. Personnel must be grounded, via a wrist strap or other safe, suitable means before any printed circuit card or other internal device is installed,

removed or adjusted.

3. Printed circuit cards must be transported in a conductive container. Boards must not be removed from protective enclosure until immediately before

installation. Removed boards must immediately be placed in protective container for transport, storage or return to factory.

Comments

This instrument is not unique in its content of ESD (electrostatic discharge) sensitive components. Most modern electronic designs contain components

that utilize metal oxide technology (NMOS, SMOS, etc.). Experience has proven that even small amounts of static electricity can damage or destroy these

devices. Damaged components, even though they appear to function properly, exhibit early failure.

Brooks Instrument designs, manufactures and tests its products to meet many national and international standards. These products must be properly

installed, operated and maintained to ensure they continue to operate within their normal specifications. The following instructions must be adhered to

and integrated into your safety program when installing, operating and maintaining Brooks Instrument products.

•To ensure proper performance, use qualified personnel to install, operate, update, program and maintain the product.

•Read all instructions prior to installing, operating and servicing the product. If this instruction manual is not the correct manual, please see back cover

for local sales office contact information. Save this instruction manual for future reference.

WARNING: Do not operate this instrument in excess of the specifications listed in the Instruction and Operation Manual. Failure to heed

this warning can result in serious personal injury and / or damage to the equipment.

• If you do not understand any of the instructions, contact your Brooks Instrument representative for clarification.

• Follow all warnings, cautions and instructions marked on and supplied with the product.

WARNING: Prior to installation ensure this instrument has the required approval ratings to meet local and national codes. Failure to heed this warning can

result in serious personal injury and / or damage to the equipment.

• Install your equipment as specified in the installation instructions of the appropriate instruction manual and per applicable local and national codes.

Connect all products to the proper electrical and pressure sources.

• Operation: (1) Slowly initiate flow into the system. Open process valves slowly to avoid flow surges. (2) Check for leaks around the flow meter inlet

and outlet connections. If no leaks are present, bring the system up to the operating pressure.

• Please make sure that the process line pressure is removed prior to service. When replacement parts are required, ensure that qualified people use

replacement parts specified by Brooks Instrument. Unauthorized parts and procedures can affect the product's performance and place the safe

operation of your process at risk. Look-alike substitutions may result in fire, electrical hazards or improper operation.

• Ensure that all equipment doors are closed and protective covers are in place to prevent electrical shock and personal injury, except when

maintenance is being performed by qualified persons.

WARNING: For liquid flow devices, if the inlet and outlet valves adjacent to the devices are to be closed for any reason, the devices must be completely

drained. Failure to do so may result in thermal expansion of the liquid that can rupture the device and may cause personal injury.

All pressure equipment with an internal pressure greater than 0.5 bar (g) and a size larger than 25mm or 1" (inch) falls under the Pressure Equipment Directive (PED).

• The Specifications Section of this manual contains instructions related to the PED directive.

• Products described in this manual are in compliance with EN directive 2014/34/EU.

• All Brooks Instrument Flowmeters fall under fluid group 1.

• Products larger than 25mm or 1" (inch) are in compliance with PED category I, II or III.

• Products of 25mm or 1" (inch) or smaller are Sound Engineering Practice (SEP).

The Brooks Instrument (electric/electronic) equipment bearing the CE mark has been successfully tested to the regulations of the Electro Magnetic

Compatibility (EMC directive 2014/30/EU).

Special attention however is required when selecting the signal cable to be used with CE marked equipment.

Quality of the signal cable, cable glands and connectors:

Brooks Instrument supplies high quality cable(s) which meets the specifications for CE certification.

If you provide your own signal cable you should use a cable which is overall completely screened with a 100% shield.

“D” or “Circular” type connectors used should be shielded with a metal shield. If applicable, metal cable glands must be used providing cable screen clamping.

The cable screen should be connected to the metal shell or gland and shielded at both ends over 360 Degrees.

The shield should be terminated to an earth ground.

Card Edge Connectors are standard non-metallic. The cables used must be screened with 100% shield to comply with CE certification.

The shield should be terminated to an earth ground.

For pin configuration : Please refer to the enclosed Instruction Manual.

European Pressure Equipment Directive (PED)

European Electromagnetic Compatibility (EMC)

Essential Instructions

Read before proceeding!

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Dear Customer,

We appreciate this opportunity to service your ow measurement and control requirements with a Brooks

Instrument device. Every day, ow customers all over the world turn to Brooks Instrument for solutions to their

gas and liquid low-ow applications. Brooks provides an array of ow measurement and control products for

various industries from biopharmaceuticals, oil and gas, fuel cell research and chemicals, to medical devices,

analytical instrumentation, semiconductor manufacturing, and more.

The Brooks product you have just received is of the highest quality available, offering superior performance,

reliability and value to the user. It is designed with the ever changing process conditions, accuracy requirements

and hostile process environments in mind to provide you with a lifetime of dependable service.

We recommend that you read this manual in its entirety. Should you require any additional information concerning

Brooks products and services, please contact your local Brooks Sales and Service Ofce listed on the back cover

of this manual or visit www.BrooksInstrument.com

Yours sincerely,

Brooks Instrument

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Section 1 Introduction

1 Introduction .....................................................................................................................................1-1

1-1 Design Features..............................................................................................................................1-1

1-2 Overview of Meter Specications....................................................................................................1-1

1-3 Pressure Ratings ............................................................................................................................1-4

1-4 Temperature Ratings.......................................................................................................................1-7

1-5 Outline and Dimensions ..................................................................................................................1-7

1-6 Optional Valves and Flow Controllers .............................................................................................1-11

1-7 Optional Electronic Features...........................................................................................................1-11

1-7-1 Current Loop 4-20 mA with HART Transmitter, with Alarms, Display and Pulse Output .................1-12

1-7-2 Foundation

Fieldbus Transmitter, with Alarms and Pulse Output .................................................1-13

1-7-3 Inductive Alarms..............................................................................................................................1-14

1-8 Product Approvals Overview ........................................................................................................... 1-15

Section 2 Installation

2-1 General ...........................................................................................................................................2-1

2-2 Receipt of Equipment......................................................................................................................2-1

2-3 Recommended Storage Practices ..................................................................................................2-1

2-4 Return Shipment .............................................................................................................................2-1

2-5 Installation of Flowmeter .................................................................................................................2-2

2-5-1 How to Remove and Reinstall GP Housing Indicator Covers .........................................................2-4

2-5-2 How to Remove and Reinstall IS Housing Indicator Covers ........................................................... 2-5

2-5-3 How to Remove and Reinstall XP Housing Indicator Covers .........................................................2-6

2-6 Electrical Connections to MT3809 with 4-20 mA/HART Transmitter, Alarms and Pulse Output. ....2-7

2-6-1 4-20 mA/HART Transmitter Intrinsically Safe Installation ...............................................................2-11

2-6-2 4-20 mA/HART Transmitter Division 2 Installation ..........................................................................2-19

2-6-3 4-20 mA/HART Transmitter Flameproof Installation .......................................................................2-19

2-7 Electrical Connection to MT3809 with Foundation Fieldbus Transmitter, Alarms and Pulse Output

2-21

2-7-1 Foundation Fieldbus Transmitter Intrinsically Safe Installation ........................................................2-24

2-8 Installation of the Model MT3809 Flowmeter with Inductive Alarms (1 or 2 switches) .................... 2-29

Section 3 Operation

3 Operation ........................................................................................................................................3-1

3-1 Start-up and Operation of Flowmeter..............................................................................................3-1

3-2 Operation of the Model MT3809 Flowmeter with a Transmitter with or without Optional

Alarms and Pulse Output for Totalization ....................................................................................3-2

3-3-1 Communication with HART Transmitter using Device Descriptor ...................................................3-3

3-3-2 Communication with Foundation Fieldbus Transmitter ....................................................................3-6

3-3-3 Communication with Transmitter using Local Operator Interface with LCD Display ....................... 3-6

3-3-4 Adjusting Inductive Alarms (1 or 2 switches) ..................................................................................3-6

3-3-5 Simulate ..........................................................................................................................................3-6

Section 4 Maintenance

4-1 General Service Information ...........................................................................................................4-1

4-2 Meter Float Cleaning (MT3809 & MT3810) ....................................................................................4-2

4-3 Meter Float Cleaning (MT3809 ETFE Option) ................................................................................4-7

4-4 Meter Indicator Reference Mark (zero) Adjustment ........................................................................4-7

4-5 Transmitter Replacement with or without Alarms and Pulse Output ...............................................4-7

4-6 Inductive Alarm Replacement .........................................................................................................4-5

4-7 Transmitter Replacement with Inductive Alarms .............................................................................4-6

4-8 Digital Display Replacement ...........................................................................................................4-6

Section A Essential Instructions....................................................................................................................... A-1

Warranty, Local Sales/Service Contact Information.............................................................................. Back Cover

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Figures

1-1 Model MT3809 and MT3810 Dimensional Drawings (mm/in) and Weights (kg/lbs) -

General Purpose Housing ...........................................................................................................1-8

1-2 Model MT3809 and MT3810 Dimensional Drawings (mm/in) and Weights (kg/lbs) -

Intrinsically Safe Housing ............................................................................................................1-9

1-3 Model MT3809 and MT3810 Dimensional Drawings (mm/in) and Weights (kg/lbs) -

Explosion Proof Housing .............................................................................................................1-10

2-1 Typical Bypass Installation ............................................................................................................ 2-3

2-2 Power Supply vs. Maximum Load Resistance ..............................................................................2-7

2-3 Mechanical Indicator Zero ............................................................................................................. 2-9

2-4 Transmitter Indicator Zero ............................................................................................................. 2-10

-5a Wiring Diagram, Model MT3809, Transmitter 4-20 mA ...................................................................2-11

2-5b Wiring Diagram, Model MT3809, Transmitter 4-20 mA (continued) ................................................2-12

2-6a Wiring Diagram, Model MT3809, 4-20 mA Transmitter, One or Two Optical

Alarms and PPU ..........................................................................................................................2-13

2-6b Wiring Diagram, Model MT3809, 4-20 mA Transmitter, One or Two Optical

Alarms and PPU (continued) .......................................................................................................2-14

2-7a Wiring Diagram, Model MT3809, One or Two Inductive Alarms ................................................... 2-15

2-7b Wiring Diagram, Model MT3809, One or Two Inductive Alarms (continued) ................................ 2-16

2-8a Wiring Diagram, Model MT3809, 4-20 mA Transmitter, One or Two Inductive Alarms ................. 2-17

2-8b Wiring Diagram, Model MT3809, 4-20 mA Transmitter, One or Two Inductive Alarms (continued)

2-18

2-9 Wiring Diagram, Model MT3809 Explosion Proof with Transmitter and/or Inductive Alarm ............

2-20

2-10 Mechanical Indicator Zero ............................................................................................................. 2-22

2-11 Foundation Fieldbus Transmitter Indicator Zero ............................................................................2-23

2-12 Wiring Diagram, Model MT3809, Foundation Fieldbus - FISCO Concept - Transmitter ................ 2-25

2-13 Wiring Diagram, Model MT3809, Foundation Fieldbus - Entity Concept - Transmitter .................. 2-26

2-14 Wiring Diagram, Model MT3809, Foundation Fieldbus - Entity Concept - Transmitter - Pulse -

Optical Alarm .............................................................................................................................2-27

2-15 Wiring Diagram, Model MT3809, Foundation Fieldbus - Entity Concept - Transmitter -

Inductive Alarms ........................................................................................................................2-28

3-1 Model MT3809 Electronics Basic Setup Menu Tree ..................................................................... 3-3

3-2 Model MT3809 Electronics Detailed Setup Menu Tree ................................................................. 3-4

3-3 Transmitter "Simulate" Connection ...............................................................................................3-6

3-3 Model MT3809 Electronics LOI Chart Menu .................................................................................3-7

4-1

Exploded View, Model MT3809G and MT3810G - Gas Service

....................................................4-5

4-2

Exploded View, Model MT3809G and MT3810G - Liquid Service

.................................................4-6

4-3

Exploded View, Model MT3809G, Size 15 (Gas or Liquid Service)

...............................................4-7

4-4

Exploded View, Model MT3809G, Size 16 (Liquid Service Only)

..................................................4-7

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Table

Number

1-1a Meter Specications ............................................................................................................................. 1-2

1-1b ELF Body/Float Stop/Float/Metering Tube Material Restrictions .........................................................1-2

1-2 Flow Capacities, Pressure Drop and Viscosity Immunity Ceiling Values .............................................1-3

1-3 Model MT3809/MT3810 Pressure Ratings, Flanged ...........................................................................1-4

1-4 Model MT3809/MT3810 Pressure Ratings, NPT Female ....................................................................1-5

1-5 Model MT3809/MT3810 Pressure Ratings, NPT Male ........................................................................1-6

1-6 Temperature Cut-off Tables ..................................................................................................................1-7

1-7 4-20 mA with HART Transmitter Description Table ..............................................................................1-12

1-8 Foundation Fieldbus Transmitter Description Table .............................................................................. 1-13

1-9 Inductive Alarms Description Table ......................................................................................................1-14

1-10 Product Approvals ................................................................................................................................1-15

1-11 ....................................................................................................................Pro-

cess and Ambient Temperature Limits ................................................................................................................. 1-18

1-12 Electrical Data: Intrinsic Safety ............................................................................................................1-20

1-13 Electrical Entries ..................................................................................................................................1-21

Tables

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

1 Introduction

The Brooks

Models MT3809 and MT3810 are rugged, all metal

owmeters offering reliable operation based on the variable area principle.

The Model MT3809 is constructed with stainless steel components for

measuring a variety of liquid and gas applications while the Model MT3809

ETFE utilizes an E/TFE lining for aggressive liquid and gas applications.

Flow rate indication is provided by means of magnetic coupling where a

magnet, encapsulated in the oat, is coupled to a rotatable magnet located

in the rear of the indicator, thus turning the dial indicator mounted on the

meter.

Optional accessories available includes transmitter with 4-20 mA

analog output with HART

communications or Foundation

Fieldbus

communications with or without congurable alarms and pulse output

for totalization. Also available are front adjustable inductive alarms, high

temperature or stainless steel indicator housings, valves, ow controllers

and certications.

1-1 Design Features

The Brooks Model MT3809 has been the “go to” meter for several years

and the choice of Engineering Contractor customers (EPC). Brooks is

proud to raise the performance of the standard meter by adding these new

features and options:

• Transmitter with 4-20mA/HART-7, or transmitter with Foundation

Fieldbus Communications

• Local Operator Interface with LCD display without removing the cover

which means changes can be made even in hazardous areas

• 316SS ameproof housing

• The broadest range of operating temperatures in the industry, the perfect

meter for even more applications

• Even lower ow rates with the current lay lengths which means one

meter style can be used for very low to high ow rates

• The new meter is designed to ASME B31.3 and gasket sealing surface is

per ASME a rugged design that does not require special gaskets at

installation

• Weldneck anges are standard which means full penetration welds that

can easily be tested for integrity

• Mechanical and alarm design that meets SIL 2 requirements

1-2 Overview of Meter Specications

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Table 1-1a Meter Specications

MT3809 MT3809ELF MT3810 TFELined

Measuring

Range

Rangeability

MeteringTube Standard

Tefzel®Lined316/316L(dualcertified

stainlesssteel)

Premium Alloy625,Hastelloy®C,TitaniumGr.II Monel®KͲ500,HastelloyC ͲͲ

Standard

316/316L(dualcertifiedstainlesssteel)

TefzelLined316/316L(dualcertified

stainlesssteel)

Premium ͲͲ

Accuracy 2%,1%, 5%,3%, 5%, 2%,

VDI/VDEclass2.5,1.6 VDI/VDEclass4,2.5 VDI/VDEclass6 VDI/VDEclass2.5

Repeatability 0.25%FullScale

1%FullScale 0.25%FullScale 0.25%FullScale

Connections Flanged: Sliponflanges

ͲtoANSIB16.5 ANSI1/2”to4”150#RFto600#RF ANSI1/2”to1”150#RFto600#RF ANSI1/2”to2”150# RFto300#RF ANSI1/2”to2”150#RFto300#RF

ͲtoDIN2527/2635

ͲFlangefinish

Threadedfemale

1/2”to2”NPT/RcͲFemale 1/2”NPT/RcͲFemale

1/2”to2”NPTͲFemale

Threadedmale 1”to2Ͳ1/2”NPTͲMale 1”NPTͲMale ͲͲ

Flanged None

Threadedmale None ͲͲ

Threadedfemalestd Viton®orTeflon® VitonorTeflon Ͳ

Threadedfemalehigh

pressure2500lbs

VitonS

ore90+Te

on

Ͳupring

Kalrez3018Shore90+TeflonbackͲupring ͲͲ

Floats Standard

HastelloyCͲ276(sizes7,8)

PVDF(sizes10Ͳ13)

Premium Alloy625,HastelloyC,TitaniumGr.II MonelKͲ500,HastelloyC ͲͲ

Indicatoronly

TransmitterALU

TransmitterSS

IndicatoronlyALU

Transm/Alarm/HiTempALU

IndicatoronlySS

Transm/Alarm/HiTempSS

MaximumFluidTemperature

300°C/570°F 150°C/270°F

MeterDimensions

ValvesͲSizes7Ͳ12/FCASizes7,8

Valve/FCASizes0Ͳ5 ValvesͲSizes7Ͳ12/FCASizes7,8 Ͳ

ProductApprovals

Currentloop4Ͳ20mA/HART®

FOUNDATION

Fieldbus

RefertoInductiveAlarmSection

LocalOperatorInterface(incl.LCD)

RefertoTemperatureTables

RefertoInductiveAlarmSectionͲ NotAvailable3810G

Flangesand

EndFittings

RefertoFOUNDATIONFieldbusSectionfordetailedspecificationsonFOUNDATIONFieldbustransmitter,Hi/LoͲalarmandpulseouputͲ NotAvailable3810G

Transmitter

InductiveAlarms

Pressure/Temperature

RefertoProductDimensionFigures

RefertoProductApprovalsPages

420°C/788°F(RefertoTemperatureTables)

SeePressure/TemperatureTables

DiecastAluminum(Alloy380),epoxypaint,glasswindow

Cast316stainlesssteel,glasswindow

Vertical(within5%oftrueͲvertical),bottominlet,topoutlet.Donotlocateinproximityofothermagneticinterferingcomponents.

Installationorientationandlocation

Cast316stainlesssteel,316stainlesssteelhardware,glasswindow

Indicator

Housing&

Covermaterial

IP67/NEMA

IP67/NEMA4X

IP64

Protection

category

SS316

MT3809 / MT3810

g/m scfm

MT3809 ELF

l/h

g/h

Hastel-C

PVDF12

MT3809 TFE Lined

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Table 1-3 Model MT3809/MT3810 Pressure Ratings, Flanged

1-3 Pressure Ratings

Please reference Tables 1-3, 1-4 and 1-5.

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Table 1-4 Model MT3809/MT3810 Pressure Ratings, NPT Female

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Table 1-5 Model MT3809/MT3810 Pressure Ratings, NPT Male

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Table 1-6 Temperature Cut-off Tables

1-5 Outline and Dimensions

Please reference Figures 1-1, 1-2 and 1-3 on the following pages.

1-4 Temperature Ratings

Please reference Table 1-6.

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Figure 1-1 Model MT3809 and MT3810 Dimensional Drawings (mm/in) and Weights (kg/lbs) - General Purpose Housing

141

5.57

137

5.40

3.85

1.5[1/16]

141

5.57

137

5.40

1.5[1/16]

3.85

Model 3809 & 3810 General Purpose Indicator Housing with

Flanged Connections mm [inches]

Model 3809 & 3810 General Purpose Indicator Housing with

Threaded Female St'd Connections mm [inches]

* Dimensions apply to threaded female standard connections only.

** Weights shown for aluminum indicator. Add 1.8 kg [4 lbs.] for steel indicator housing.

Meter

Size

Connection

Weight (Approx.)**

0-5

7 & 8

1/2" Threaded Female St'd

1" Threaded Female St'd

1-1/2" Threaded Female St'd

2" Threaded Female St'd

225 [8.85]*

300 [11.81]*

99 [3.90]

107 [4.21]

116 [4.57]

122 [4.78]

63 [2.48]

71 [2.80]

80 [3.15]

86 [3.39]

76 [2.98]

2.7 kg [6 lbs. ]

4.5 kg [10 lbs. ]

6.8 kg [15 lbs. ]

7.7 kg [17 lbs. ]

0-5

7 & 8

1/2" Flange

1" Flange

1-1/2" Flange

2" Flange

3" Flange

4" Flange

250 [9.84]

350 [13.78]

99 [3.90]

106 [4.18]

115 [4.54]

121 [4.63]

139 [5.46]

152 [5.98]

63 [2.48]

70 [2.76]

79 [3.12]

85 [3.36]

103 [4.05]

118 [4.65]

76 [2.98]

126 [4.95]

4.1 kg [9 lbs. ]

7.7 kg [17 lbs. ]

12.2 kg [27 lbs. ]

14.1 kg [31 lbs. ]

20.0 kg [44 lbs. ]

37.6 kg [83 lbs. ]

Meter

Size

0-51/2" Threaded Female 225 [8.85]99 [3.90] 63 [2.56]61 [2.40] 2.7 kg [6 lbs. ]

1" Threaded Male 200 [7.87] 100 [3.94]65 [2.56] 48 [1.89]2.7 kg [6 lbs. ]

7 & 81/2" Threaded Female 225 [8.85]99 [3.90] 63 [2.56]61 [2.40] 2.7 kg [6 lbs. ]

3/4" Threaded Female 225 [8.85]99 [3.90] 63 [2.56]61 [2.40] 2.7 kg [6 lbs. ]

1" Threaded Male 200 [7.87] 100 [3.94]65 [2.56] 48 [1.89]2.7 kg [6 lbs. ]

10 1" Threaded Female 300 [11.81] 107 [4.21]71 [2.80] 98 [3.86]4.5 kg [10 lbs. ]

1-1/2" Threaded Male 250 [9.84] 108 [4.25]72 [2.83] 73 [2.87]4.5 kg [10 lbs. ]

12 1-1/2" Threaded Female 300 [11.81] 116 [4.57]80 [3.15] 98 [3.86]6.8 kg [15 lbs. ]

2-1/2" Threaded Male 250 [9.84] 118 [4.65]83 [3.27] 73 [2.87]6.8 kg [15 lbs. ]

13 2" Threaded Female 300 [11.81] 122 [4.78]86 [3.39] 98 [3.86]7.7 kg [17 lbs. ]

0-5 250 [9.84]99 [3.90] 63 [2.48]73 [2.87] 4.1 kg [9 lbs. ] - 6.5 kg [14 lbs. ]

7 & 8 250 [9.84]99 [3.90] 63 [2.48]73 [2.87] 4.1 kg [9 lbs. ] - 11.9 kg [12 lbs. ]

10 250 [9.84] 106 [4.13]70 [2.76] 73 [2.87]7.7 kg [17 lbs. ] - 14.5 kg [32 lbs. ]

12 250 [9.84] 115 [4.53]79 [3.11] 73 [2.87]12.2 kg [27 lbs. ] - 17.7 kg [39 lbs. ]

13 250 [9.84] 122 [4.80]85 [3.35] 73 [2.87]

14.1 kg [31 lbs. ] - 28 kg [62 lbs. ]

15 250 [9.84] 139 [5.47] 103 [4.06]73 [2.87] 20.0 kg [44 lbs. ] - 45 kg [99 lbs. ]

16 350 [13.78] 154 [6.06] 118 [4.65] 123 [484]

37.6 kg [83 lbs. ] - 58.6 kg [129 lbs. ]

Weight (Approx.)*

Flanged

(ANSI, DIN and JIS)

Connection A B C D

*Weights shown for aluminum indicator. Add 1.8 [4 lbs.] for steel indicator housing

Model 3809 & 3810 General Purpose Indicator Housing with

Threaded Female Connections mm [inches]

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Figure 1-2 Model MT3809 and MT3810 Dimensional Drawings (mm/in) and Weights (kg/lbs) - Intrinsically Safe Housing

160

6.29

1.5[1/16]

160

6.29

160

6.28

1.5[1/16]

160

6.29

Model 3809 Intrinsically Safe Indicator Housing with

Threaded Female St'd Connections mm [inches]

Model 3809 Intrinsically Safe Indicator Housing with

Flanged Connections mm [inches]

* Dimensions apply to threaded female standard connections only.

Meter

Size

Connection

Weight (Approx.)

0-5

7 & 8

1/2" Threaded Female St'd

1" Threaded Female St'd

1-1/2" Threaded Female St'd

2" Threaded Female St'd

225 [8.85]*

300 [11.81]*

104 [4.09]

112 [4.41]

121 [4.76]

127 [5.00]

182 [7.17]

52 [2.04]

5.4 kg [12 lbs. ]

7.3 kg [16 lbs. ]

9.5 kg [21 lbs. ]

10.4 kg [23 lbs. ]

0-5

7 & 8

1/2" Flange

1" Flange

1-1/2" Flange

2" Flange

3" Flange

4" Flange

250 [9.84]

350 [13.78]

104 [4.09]

111 [4.37]

120 [4.73]

126 [4.97]

144 [5.67]

159 [6.26]

182 [7.17]

52 [2.04]

102 [4.00]

6.8 kg [15 lbs. ]

10.4 kg [23 lbs. ]

15.0 kg [33 lbs. ]

16.8 kg [37 lbs. ]

22.7 kg [50 lbs. ]

40.4 kg [89 lbs. ]

Meter

Size

0-51/2" Threaded Female 225 [8.85] 104 [4.10] 183 [7.20]40 [1.57] 5.4 kg [12 lbs. ]

1" Threaded Male 200 [7.87] 105 [4.13] 183 [7.20]27 [1.06] 5.4 kg [12 lbs. ]

7 & 81/2" Threaded Female 225 [8.85] 104 [4.10] 183 [7.20]40 [1.57] 5.4 kg [12 lbs. ]

3/4" Threaded Female 225 [8.85] 104 [4.10] 183 [7.20]40 [1.57] 5.4 kg [12 lbs. ]

1" Threaded Male 200 [7.87] 105 [4.13] 183 [7.20]27 [1.06] 5.4 kg [12 lbs. ]

10 1" Threaded Female 300 [11.81] 121 [4.76] 183 [7.20]77 [3.03] 7.3 kg [16 lbs. ]

1-1/2" Threaded Male 250 [9.84] 113 [4.45] 183 [7.20]52 [2.05] 7.3 kg [16 lbs. ]

12 1-1/2" Threaded Female 300 [11.81] 121 [4.76] 183 [7.20]77 [3.03] 9.5 kg [21 lbs. ]

2-1/2" Threaded Male 250 [9.84] 120 [4.72] 183 [7.20]52 [2.05] 9.5 kg [21 lbs. ]

13 2" Threaded Female 300 [11.81] 127 [5.00] 183 [7.20]77 [3.03] 10.4kg [23 lbs. ]

0-5 250 [9.84] 104 [4.10] 183 [7.20]52 [2.05] 6.8 kg [15 lbs. ] - 9.2 kg [20 lbs. ]

7 & 8 250 [9.84] 104 [4.10] 183 [7.20]52 [2.05] 6.8 kg [15 lbs. ] - 14.6 kg [32 lbs. ]

10 250 [9.84] 111 [4.37] 183 [7.20]53 [2.05] 10.4 kg [23 lbs. ] - 17.2 kg [38 lbs. ]

12 250 [9.84] 120 [4.72] 183 [7.20]54 [2.05] 15 kg [33 lbs. ] - 20.5 kg [45 lbs. ]

13 250 [9.84] 126 [4.96] 183 [7.20]55 [2.05] 16.8 kg [37 lbs. ] - 30.7 kg [68 lbs. ]

15 250 [9.84] 144 [5.67] 183 [7.20]56 [2.05] 22.7 kg [50 lbs. ] - 47.7 kg [105 lbs. ]

16 350 [13.78] 159 [6.26] 183 [7.20]57 [2.05] 40.4 kg [89 lbs. ] - 61.4 kg [135 lbs. ]

Flanged

(ANSI, DIN and JIS)

Connection A B C D Weight (Approx.)*

Model 3809 Intrinsically Safe Indicator Housing with

Threaded Female Connections mm [inches]

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Figure 1-3 Model MT3809 and MT3810 Dimensional Drawings (mm/in) and Weights (kg/lbs) - Explosion Proof Housing

165

6.50

1.5[1/16]

172

6.75

165

6.50

1.5[1/16]

172

6.75

Model 3809 Explosion Proof Indicator Housing with

Flanged Connections mm [inches]

Model 3809 Explosion Proof Indicator Housing with

Threaded Female St'd Connections mm [inches]

* Dimensions apply to threaded female standard connections only.

Meter

Size

Connection

Weight (Approx.)

0-5

7 & 8

1/2" Threaded Female St'd

1" Threaded Female St'd

1-1/2" Threaded Female St'd

2" Threaded Female St'd

225 [8.85]*

300 [11.81]*

112 [4.41]

120 [4.73]

129 [5.08]

135 [5.31]

218 [8.57]

44 [1.72]

11.8 kg [26 lbs. ]

13.6 kg [30 lbs. ]

15.9 kg [35 lbs. ]

16.8 kg [37 lbs. ]

0-5

7 & 8

1/2" Flange

1" Flange

1-1/2" Flange

2" Flange

3" Flange

4" Flange

250 [9.84]

350 [13.78]

113 [4.45]

120 [4.73]

129 [5.08]

135 [5.31]

153 [6.02]

168 [6.61]

218 [8.57]

44 [1.72]

94 [3.69]

13.2 kg [29 lbs. ]

16.8 kg [37 lbs. ]

21.3 kg [47 lbs. ]

23.1 kg [51 lbs. ]

29.0 kg [64 lbs. ]

46.7 kg [103 lbs. ]

Meter

Size

0-51/2" Threaded Female 225 [8.85] 113 [4.45] 218 [8.58]41 [1.61] 11.8 kg [26 lbs. ]

1" Threaded Male 200 [7.87] 114 [4.49] 218 [8.58]28 [1.10] 11.8 kg [26 lbs. ]

7 & 81/2" Threaded Female 225 [8.85] 113 [4.45] 218 [8.58]41 [1.61] 11.8 kg [26 lbs. ]

3/4" Threaded Female 225 [8.85] 113 [4.45] 218 [8.58]41 [1.61] 11.8 kg [26 lbs. ]

1" Threaded Male 200 [7.87] 114 [4.49] 218 [8.58]28 [1.10] 11.8 kg [26 lbs. ]

10 1" Threaded Female 300 [11.81] 120 [4.72] 218 [8.58]78 [3.07] 13.6 kg [30 lbs. ]

1-1/2" Threaded Male 250 [9.84] 121 [4.76] 218 [8.58]53 [2.09] 13.6 kg [30 lbs. ]

12 1-1/2" Threaded Female 300 [11.81] 129 [5.08] 218 [8.58]78 [3.07] 15.9 kg [35 lbs. ]

2-1/2" Threaded Male 250 [9.84] 131 [5.16] 218 [8.58]53 [2.09] 15.9 kg [35 lbs. ]

13 2" Threaded Female 300 [11.81] 135 [5.31] 218 [8.58]78 [3.07] 16.8kg [23 lbs. ]

0-5 250 [9.84] 113 [4.45]

218 [8.58]

53 [2.09]

13.2 kg [29 lbs. ] - 15.6 kg [34 lbs. ]

7 & 8 250 [9.84] 113 [4.45]

218 [8.58]

53 [2.09]

13.2 kg [29 lbs. ] - 21 kg [46 lbs. ]

10 250 [9.84] 120 [4.72]

218 [8.58]

53 [2.09]

16.8 kg [37 lbs. ] - 23.6 kg [52 lbs. ]

250 [9.84]

129 [5.08]

218 [8.58]

53 [2.09]

21.3 kg [47 lbs. ] - 26.8 kg [59 lbs. ]

13 250 [9.84] 135 [5.31]

218 [8.58]

53 [2.09]

23.1 kg [51 lbs. ] - 37 kg [81 lbs. ]

15 250 [9.84] 153 [6.02]

218 [8.58]

53 [2.09]

29 kg [64 lbs. ] - 54 kg [119 lbs. ]

16 350 [13.78] 168 [6.61]

218 [8.58]

103 [4.06]

46.7 kg [103 lbs. ] - 67.7 kg [149 lbs. ]

Weight (Approx.)*

Flanged

(ANSI, DIN and JIS)

Connection A B C D

Model 3809 Explosion Proof Indicator Housing with

Threaded Female Connections mm [inches]

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

1-6 Optional Valves and Flow Controllers

Needle valves and ow controllers may be externally piped into the inlet or

outlet side of the instrument. Needle valves can be supplied up to size 12

1-1/2" maximum 10000 l/hr / 46 gpm water equivalent. Needle valves and

ow controllers will be supplied separately with the anged meter.

1-7 Optional Electronic Features

Electronic equipment available with the Model MT3809 includes:

• Current loop 4-20mA/HART Transmitter with Alarms and Pulse Output

• Foundation Fieldbus Transmitter with Alarms and Pulse Output

• Inductive Alarms; stand-alone or in combination with above transmitters

Refer to the table below for the model code nomenclature for the

electronics options. All models are designed to be either intrinsically safe

or explosion proof.

Nomenclature and Type Designation

MT3809 … B …

I-IV XV

Electronics

configuration

B, C

D … L

M … U

Indicator with inductive alarm, 1 or 2 switches

Transmitter, 4 – 20 mA / Hart, with optionally:

- pulse output

- inductive alarm contact(s)

- LOI

or combinations thereof.

Transmitter, FOUNDATION Fieldbus, with optionally:

- pulse output

- inductive alarm contact(s)

- LOI

or combinations thereof.

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

Design Features

• 4-20 mA analog output for owrate

• Bell-202 modulated HART digital communication over the 4-20 mA signal

• Current loop powered 2-wire connection

• User selectable 0% and 100% analog output ranges with optional

smoothing

• Flexible (mix & match) units of measure for owrates, totals,

temperatures, densities, etc.

• Two ow totalizers: Resettable and inventory totalization

• User congurable, scalable pulse output for various engineering units

• Hi- and Lo-ow alarm output

Description

The 4-20 mA with HART transmitter is a compact microprocessor device

designed to interface directly with the Model MT3809. This transmitter

includes a Hi- and Lo alarm switch output and a pulse output.

The HART digital communication signals are superimposed on top of the

4-20 mA signal, allowing communication of more than just the process

variable.

The transmitter is HART-programmable or for numerous variables such as

ow rate, totalization, calibration factors, and high-low alarm parameters.

It is programmable with easy-to-use hand held congurators. Prior to

shipment, commonly used default values are programmed by Brooks to

ensure ease of operation and quick startup. However, parameters may be

reprogrammed by the user if needed. Flow rate information may be viewed

locally at the meter scale, LCD display or displayed remotely.

Powersupplyvoltage 21to30Vdc:(2Ͳwirecurrentlooptransmitter)

Loopcurrent/currentconsumption

range

3.8to22.0mA.

Opencollectoralarmoutput

Opticallyisolatedoutputsassignabletoalarms.

•Max.offͲstatevoltage:30Vdc

•Max.offͲstatecurrent:0,05mA

•Max.onͲstatevoltage:1.2Vdc

•Max.onͲstatecurrent:20mA

Opticallyisolated.Scalabletoavarietyofengineeringunitsystems(pulsesperliter,gallons,

etc.).

•Range:1Hzto1kHz

•Max.offͲstatevoltage:30Vdc

•Max.offͲstatecurrent:0.05mA

•Max.onͲstatevoltage:1.2Vdc

•Max.onͲstatecurrent:20mA

TemperatureSpecification SeeTemperatureCutͲoff Table

M20x1,5accordingtoISO(1/2"NPT,3/4”NPT(F)orcableglandoptional)

•Brass/Nickelplatedcableglandcablediameterrange8Ͳ11mm(Aluminumhousing)

•Stainlesssteelcableglandcablediameterrange7Ͳ10.5mm(SShousing)

Linearity Lessthan1%atmax.current.

Temperatureinfluence Lessthan0.04%per°C.

Voltageinfluence Lessthan0.002%/Vdc.

Loadresistanceinfluence ±0.1%fullscale.

HARTRevision HARTͲ7

HiͲandLoͲalarmoutputs

PulseOutput

ElectricalConnector

Table 1-7 4-20 mA with HART Transmitter Description Table

1-7-1 Current Loop 4-20 mA with HART Transmitter, with Alarms, Display and Pulse Output

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

1-7-2 Foundation Fieldbus Transmitter, with Alarms and Pulse Output

Design Features

• Foundation

Fieldbus digital communication network interface

• Ease of wiring and installation with a single 2-wire bus connection

• Powered over 2-wire Foundation

Fieldbus connection

• Flexible (mix & match) units of measure for owrates, totals,

temperatures, densities, etc.

• Two ow totalizers: Resettable and inventory totalization

• User congurable, scalable pulse output for various engineering units

• Hi- and Lo-ow alarm output

Description

The Foundation

Fieldbus transmitter is a compact microprocessor device

designed to interface directly with the Model MT3809.

The transmitter communicates over the 2-wire network per the

international Foundation

Fieldbus standard for access to numerous

variables such as ow rate, totalization, calibration factors, and high-low

alarm parameters.

Table 1-8 Foundation Fieldbus Transmitter Description Table

Powersupplyvoltage 9Ͳ32Vdc

Powersupplyprotection Protectedagainstreversepolarity

Currentconsumption 12mA

Entiretransmitterispoweredfrom2Ͳwirebus

HiͲandLoͲalarmoutputs Opencollectoralarmoutput

Opticallyisolatedoutputsassignabletoalarms.

•Max.offͲstatevoltage:30Vdc

•Max.offͲstatecurrent:0,05mA

•Max.onͲstatevoltage:1.2Vdc

•Max.onͲstatecurrent:20mA

PulseOutput

Opticallyisolated.Scalabletoavarietyofengineeringunitsystems(pulsesperliter,gallons,

etc.).

•Range:1Hzto1kHz

•Max.offͲstatevoltage:30Vdc

•Max.offͲstatecurrent:0.05mA

•Max.onͲstatevoltage:1.2Vdc

•Max.onͲstatecurrent:20mA

TemperatureSpecification SeeTemperatureCutͲoffTable

ElectricalConnector M20x1,5accordingtoISO(1/2"NPT,3/4”NPT(F)orcableglandoptional)

•Brass/Nickelplatedcableglandcablediameterrange8Ͳ11mm(Aluminumhousing)

•Stainlesssteelcableglandcablediameterrange7Ͳ10.5mm(SShousing)

Linearity Lessthan1%

TemperatureInfluence Lessthan0.04%per°C

Voltageinfluence Lessthan0.002%/Vdc

FOUNDATIONFieldbusRevision ITK6

Installation and Operation Manual

X-VA-MT3809G-MT3810G-eng

Part Number: 541B182AAG

July, 2018

Models MT3809G & MT3810G

1-7-3 Inductive Alarms

Design Features

• 1 or 2 normally open inductive limit switches

• Optional intrinsically safe power supply/amplier/relay unit

• For low or high limit signaling/switching

• Front adjustable

• Optional Relay Power Supply – recommended

Description

One or two electronic limit switches can be installed in the indicator

housing to allow signaling or switching functions on a preset ow value.

The limit switch operates as a slot initiator that is inductively actuated

by a disc mounted on the pointer shaft. Any ow value can be used for

setting the limit value by sliding the initiator along the indicator scale.

Minimum setting distance between two limit switches is approximately

40% full scale. The position of the initiator also serves to visually indicate

the signaling set value. Settings can be adjusted by removing the indicator

cover, loosening, moving and retightening of the alarm indication needle,

and replacement of the indicator front cover. Refer to Section 2-5-1.

Table 1-9 Inductive Alarms Description Table

Powersupplyvoltage 5Ͳ25Vdc:(8Vdcnominal)

ImpedanceͲApproximately1kohmwithcamabsent

ͲApproximately8kohmwithcampresent

Ambientandprocesstemperature SeeTemperatureCutͲoffTable

ElectricalConnector M20x1,5accordingtoISO(1/2"NPT,3/4”NPT(F)orcableglandoptional)

•Brass/Nickelplatedcableglandcablediameterrange8Ͳ11mm(Aluminumhousing)

•Stainlesssteelcableglandcablediameterrange7Ͳ10.5mm(SShousing)

Leht laadib ...

Brooks 3809G / 3809G ELF / 3809G TFE Lined / 3810G Kasutusjuhend

Bränd: Brooks

Mudel: 3809G / 3809G ELF / 3809G TFE Lined / 3810G

Tüüp: Kasutusjuhend

See käsiraamat sobib ka

Laadige alla PDF

aruanne

Brooks 3809G / 3809G ELF / 3809G TFE Lined / 3810G Kasutusjuhend

See käsiraamat sobib ka

Brooks 3809G / 3809G ELF / 3809G TFE Lined / 3810G Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid