GPS Digital
Speed Display
Version 1.2 - Amp Style
Table of Contents
Introduction
Features
Installation
4-Pin Amp
Adapter
Digital Display Circuit Board
Conguring the Display for use w/ Adapter
Review
Power
Remove the Case
Locate the Switches
Flip the Switches
Replace the Cover
Monitor/Speed Constant Diagram
Monitor/Speed Constant Diagram cont.
6 Dip-Switch Monitor Congurations
Dip-Switch Special Congurations
Radar/GPS Adapters
Sensor-1 Warranty
Sensor-1 Return Policy
Notes
Notes
Page 2
Page 2
Page 3
Page 3
Page 3
Page 3
Page 4
Page 4
Page 4
Page 4
Page 4
Page 4
Page 4
Page 5
Page 6
Page 6
Page 6
Page 7
Page 8
Page 8
Page 9
Page 10
Page 2
GPS Digital Speed Display
User Manual
Introduction
The GPS Digital Speed Display uses the GPS to give you an
accurate ground speed. It features a large digital display, a
red “status” light and a green “GPS” light. You will also no-
tice a 4-pin amp connector on the left side. The wire on the
right side leads to the “mushroom” antenna.
Features: When in operation, the display will show your true
ground speed. The two lights indicate your GPS links. A
steadily shining red light indicates that you have a link to a
WAAS satellite, while a blinking red light means that you do
not have a WAAS satellite link. A steady green light means
that you have a link to 4 or more satellites. NOTE: You do
not have to have a steady red light for your display to oper-
ate correctly.
(Note: The red “Status” light applies to version 1.2. If you
have an earlier version of the digital speed display, the red
light will say “Power” and will not blink and does not indicate
a WAAS signal.)
Page 3
Page 4
Installation
4-Pin Amp: When you receive your GPS Digital Speed Dis-
play and Antenna, it will be ready to hookup to any 4-pin amp
speed input. This means that you should be able to hook it
up to most DICKEY-john, John Deere, and Case IH monitors
without any alterations. Simply hook the four-pin end of the
display in the 4-pin amp on your monitor.
Adapter: If you are using a monitor without a 4-pin amp,
you will need an adapter. Monitors that you would need an
adapter cable for are some DICKEY-john, Raven, Hiniker,
Micro-Trak and Tee-Jet monitors, or if you are connecting
directly to a tractor radar cable. Adapter cables for any of
these are available through Sensor-1.
The adapter cable will connect the 4-pin amp on the side
of the speed display to your monitor or tractor radar cable.
Simply match the appropriate ends. Before you connect the
unit to a power source, there is still one thing you must do if
you are using an adapter.
Switch
#1
Switch
#6
Switch
#5
Switch
#4
Switch
#3
Switch
#2
4-Pin Amp
Digital Display Circuit Board
Red “Status”
Light
Green “GPS”
Light
Switches
are
“ON” by
default.
Switches are “ON” by default.
To have the display working correctly, you will have to open
the unit up and change a number of dip-switches. The unit’s
default setting is to have all of these switches on. If using an
adapter, you will have to turn one or more of these switches
off. To do this, simply follow the steps below:
1. Review: Review the Digital Display Circuit Board above
to familiarize yourself with its parts.
2. Power: Make sure the unit is not hooked up to any sort of
power source.
3. Remove the Case: Turn the unit over and remove the
four screws on the back. Remove the top case, revealing
the printed circuit board inside.
4. Locate the Switches: Locate the set of 6 dip-switches.
They are located to the left of the display board and to
the right of the 4-pin amp connector.
5. Flip the Switches: Using a needle or other small item,
carefully ip the appropriate dip-switches. Use the fol-
lowing guide to be sure of which switches to ip. To give
an example, if you are trying to connect the display to a
Tee-Jet monitor, you will have to open the unit up and ip
switch #1 and #3 off, but leave switches #2, #4, #5, and
#6 on.
6. Replace the cover: When you are sure that you have the
switches in the correct positions for your needs, place the
front cover back on the unit and screw it back together.
You may now connect your connector cable to the display
unit and to your monitor. The unit should now work correctly
with your monitor.
Page 5
Conguring the Display for
use with an Adapter
Page 6
Type of Monitor Constant Hz/mph Connector Type
MT84 Calc/FlowTrak 1.74 10.12 2 Pin w/ Adapter
Hiniker Acre Commander 26.931 10.12 3-Pin Cannon
Hiniker Computer Facts 13206.661 10.12 3-Pin Cannon
Hiniker Spray Commander 378.583 10.12 3-Pin Cannon
Hiniker 8100 24.5 10.12 3-Pin Cannon
AutoTrol .875 10.12 3-Pin Metri-Pack
Calc-An-Acre .875 10.12 3-Pin Metri-Pack
Calc-An-Acre II .239 57 3-Pin Metri-Pack
Flow Trak .875 10.12 3-Pin Metri-Pack
Flow Trak II .239 57 3-Pin Metri-Pack
GSC-1000 .239 57 3-Pin Metri-Pack
MT Gen I & MT-340F .90 10.12 3-Pin Metri-Pack
MT Gen II, MT 3405F II .189 57 3-Pin Metri-Pack
MT-NH311 .239 57 3-Pin Metri-Pack
MT-2405F .875 10.12 3-Pin Metri-Pack
MT-2405F II .239 57 3-Pin Metri-Pack
MT-3405D .239 57 3-Pin Metri-Pack
MT-3405F .875 10.12 3-Pin Metri-Pack
MT-3405F II .239 57 3-Pin Metri-Pack
MT9000 .90 10.12 3-Pin Metri-Pack
ProPlant .239 57 3-Pin Metri-Pack
ProSeed .239 57 3-Pin Metri-Pack
RoadMaster .239 57 3-Pin Metri-Pack
SodPro .875 10.12 3-Pin Metri-Pack
SodPro II .239 57 3-Pin Metri-Pack
Speed-O-Matic .875 10.12 3-Pin Metri-Pack
SprayMate .875 10.12 3-Pin Metri-Pack
SprayMate II .239 57 3-Pin Metri-Pack
MT3000 1.80 10.12 3-Pin Weather-Pack
Tee-Jet 844 1150 57 3-Pin Deutch
Tee-Jet 855 1167 57 3-Pin Deutch
Raven 440, 460 586 57 3-Pin Conxall
DICKEY-john 3000 1480 57 4-Pin Amp
Early Riser 7773 57 4-Pin Amp
John Deere 200 & 300 7773 57 4-Pin Amp
Continued on top of next page.
6 dip-switch Monitor Congurations
Dip-Switches Pulse
Rate
1 PPS
No PPS
MPH
KPH
WAAS
Enable
Loss - GPS
Signal Delay
1 2 3 4 5 6
OFF OFF x x x x Reserved
ON OFF x x x x 44 Hz N/A N/A N/A N/A
OFF ON x x x x 10.12 Hz N/A N/A N/A N/A
ON ON x x x x 57 Hz N/A N/A N/A N/A
x x OFF x x x N/A No PPS
1.
N/A N/A N/A
x x ON x x x N/A 1 PPS
2.
N/A N/A N/A
x x x OFF x x N/A N/A KPH N/A N/A
x x x ON x x N/A N/A MPH N/A N/A
x x x x OFF x N/A N/A N/A WAAS Off N/A
x x x x ON x N/A N/A N/A WAAS On N/A
x x x x x OFF N/A N/A N/A N/A 2 Min.
3.
x x x x x ON N/A N/A N/A N/A 30 Sec.
3.
x Indicates that switch can be in either position.
1. No Output on loss of GPS Signal
2. 1 PPS Output on loss of GPS Signal
3. Speed output after loss of GPS Signal
Dip-Switch Special Congurations
Conguration Switch
1 2 3 4 5 6
AMP (default settings) 57 Hz On On On On On On
DICKEY-john 44 Hz On Off On On On On
Raven 57 Hz On On Off On On On
Micro-Trak 10.12 Hz Off On Off On On On
Hiniker 10.12 Hz Off On Off On On On
Tee-Jet 10.12 Hz Off On Off On On On
Page 7
Type of Monitor Constant Hz/mph Connector Type
Mid-Tech ARC6000 1220 57 4-Pin Amp
Seed Manager 7773 57 4-Pin Amp
Sensor-1 9816H 7773 57 4-Pin Amp
Sensor-1 PM2005 15546 57 4-Pin Amp
Note:
Page 8
Cigarette Lighter Adapter
Cigarette Lighter Adapter with DB9
AA04RSR-CLP List Price $35.00
YA04RSR-DB9F&CLP List Price $50.00
Raven Monitor
Micro-Trak Monitor
MT-3000 Monitor
John Deere Tractor
Case-IH Tractor
(Weather-Pack 4 pin tower)
John Deere Tractor
(Weather-Pack 4 pin tower)
Tee-Jet Monitor
Hinker Monitor
Radar/GPS Adapters
AA04RSR-TJ List Price $35.00
AA04RSR-TJ855
AA04RSR-4WPTHJD List Price $35.00
AA04RSR-3MMH (Micro-Trak)
AA04RSR-3MJH (John Deere) List Price $35.00
AA04RSR-4WPTHIH List Price $35.00
AA04RSR-4WPTSJD List Price $35.00
AA04RSR-RP List Price $35.00
AA04RSR-MT3H List Price $35.00
AA04RSR-3CS List Price $35.00
Digital In-Line Speed Read Out
YA04RSR-DB9F&A04RSP List Price $50.00
Adapts to DB9 & DICKEY-john Monitor
Call for your custom adapter!
Page 9
Sensor-1 Warranty
Sensor-1 warrants to the original purchaser for use that, if any
part of the product proves to be defective in material or work-
manship within three years from date of original purchase,
Sensor-1 will (at our option) either replace or repair said part.
This warranty does not apply to damage resulting from misuse,
neglect, accident, or improper installation and maintenance.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU
OF ALL OTHER WARRANTIES OF MERCHANTABILITY FIT-
NESS FOR PURPOSE AND OF ANY OTHER TYPE, WHETH-
ER EXPRESSED OR IMPLIED. Sensor-1 neither assumes
nor authorizes anyone to assume for it any other obliga-
tion or liability in connection with said part and will not be
liable for consequential damages. Purchase accepts these
terms and warranty limitations unless product is returned
within thirty days for a full refund if the product is not
used. A 5% restocking fee will apply to all returned items.
Special orders are non-refundable.
Sensor-1 Return Policy
Sensor-1 offers a full refund or replacement for merchandise
returned unused in resalable condition. All merchandise must
be returned in its original packaging within 30 days or original
invoice date. All returned items must be accompanied by a
Return Merchandise Authorization number (RMA#). You may
obtain an RMA# by calling a Sensor-1 service representative at
1-800-736-7671. All returns may be subject to a 15% restock-
ing fee. Any item that is returned within the warranty period, as
defective, will be tested by one of our technicians and either
repaired or replaced. Any parts returned that have been used
will be replaced or repaired and returned to sender. If credit is
required, a 15% restocking fee is charged. Parts returned due
to customer error will be subject to a restocking fee and any
non-catalog or custom items are non-returnable. All shipping
charges are non-refundable.
Page 10
Notes
Notes
Page 11
202 Main Street
Princeton, Kansas 66078
GPS Digital
Speed Display
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
teistes keeltes
- English: Sensor-1 GPS Display Owner's manual
Muud dokumendid
-
Trane Tracer Summit Hardware And Software Installation Manual
-
JVC GZ-RX510 Kasutusjuhend
-
Dante DLC1981 Kasutusjuhend
-
Dakota Digital PAC-3500 Technical Manual
-
Breezary 24006-BK Kasutusjuhend
-
Smithco Spraystar 2007/2007D & 2008/2008D Rate-Sync Omaniku manuaal
-
-
-
Juniper ACX1100 Kasutusjuhend
