Makita CL002G Kasutusjuhend

Bränd: Makita

Mudel: CL002G

Tüüp: Kasutusjuhend

CL002G

EN Cordless Cleaner INSTRUCTION MANUAL 9

SV Sladdlös dammsugare BRUKSANVISNING 18

NO Batteridrevet støvsuger BRUKSANVISNING 27

FI Akkukäyttöinen pölynimuri KÄYTTÖOHJE 36

DA Akku støvsuger BRUGSANVISNING 45

LV Bezvadu tīrītājs LIETOŠANAS INSTRUKCIJA 54

LT Belaidis siurblys NAUDOJIMO INSTRUKCIJA 63

ET Juhtmeta käsitolmuimeja KASUTUSJUHEND 72

RU Аккумуляторный пылесос РУКОВОДСТВО ПО

ЭКСПЛУАТАЦИИ 81

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

Fig.16

Fig.17

Fig.18

Fig.19

Fig.20

Fig.21

Fig.22

Fig.23

Fig.24

Fig.25

Fig.26

Fig.27

Fig.28

Fig.29

Fig.30

Fig.31

Fig.32

Fig.33

Fig.34

Fig.35

Fig.36

Fig.37

Fig.38

Fig.39

Fig.40

Fig.41

Fig.42

Fig.43

Fig.44

Fig.45

Fig.46

Fig.47

Fig.48

Fig.49

9ENGLISH

ENGLISH (Original instructions)

WARNING

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sen-

sory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruc-

tion concerning use of the appliance in a safe way and understand the hazards involved.

• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children with-

out supervision.

• See the chapter “SPECIFICATIONS” for the type reference of the battery.

• See the section “Installing or removing battery cartridge” for how to remove or install the battery.

• When disposing the battery cartridge, remove it from the tool and dispose of it in a safe place. Follow your local

regulations relating to disposal of battery.

• If the tool is not used for a long period of time, the battery must be removed from the tool.

• Do not short the battery cartridge.

• See the chapter “MAINTENANCE” for the appropriate details of precautions during user maintenance.

SPECIFICATIONS

Model: CL002G

Capacity with dust bag 500 mL

with paper lter 330 mL

Continuous use

(with battery BL4025)

1 (Quiet mode) Approx. 80 min

2 (Normal speed mode) Approx. 40 min

3 (High speed mode) Approx. 25 min

4 (Max speed mode) Approx. 16 min

Overall length (with pipe, nozzle, and battery BL4025) 1,066 mm

Rated voltage D.C. 36 V - 40 V max

Net weight 1.8 - 2.4 kg

• Due to our continuing program of research and development, the specications herein are subject to change

without notice.

• Specications may dier from country to country.

• The weight does not include accessories but battery cartridge(s). The lightest and heaviest combination weight

of the appliance and battery cartridge(s) are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL4020* / BL4025* / BL4040* / BL4050F

* : Recommended battery

Charger DC40RA / DC40RB / DC40RC

• Some of the battery cartridges and chargers listed above may not be available depending on your region of

residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

and chargers may cause injury and/or re.

Symbols

The followings show the symbols which may be used

for the equipment. Be sure that you understand their

meaning before use.

Read the instruction manual.

A representative battery applicable to this

product.

10 ENGLISH

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical

and electronic equipment, accumulators

and batteries may have a negative impact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household

waste!

In accordance with the European Directive

on waste electrical and electronic equip-

ment and on accumulators and batteries

and waste accumulators and batteries,

as well as their adaptation to national law,

waste electrical equipment, batteries and

accumulators should be stored separately

and delivered to a separate collection point

for municipal waste, operating in accor-

dance with the regulations on environmen-

tal protection.

This is indicated by the symbol of the

crossed-out wheeled bin placed on the

equipment.

Intended use

The tool is intended for collecting dry dust.

SAFETY WARNINGS

Cordless cleaner safety warnings

WARNING: IMPORTANT! READ CAREFULLY

all safety warnings and all instructions BEFORE

USE. Failure to follow the warnings and instructions

may result in electric shock, re and/or serious injury.

1. Do not expose to rain. Store indoors.

Do not allow to be used as a toy. Close attention

is necessary when used by or near children.

3. Use only as described in this manual. Use only

manufacturer's recommended attachments.

4. Do not use with damaged battery. If appliance

is not working as it should, has been dropped,

damaged, left outdoors, or dropped into water,

return it to a service center.

5. Do not handle appliance with wet hands.

Do not put any object into openings. Do not use

with any opening blocked; keep free of dust, lint,

hair, and anything that may reduce air ow.

7. Keep hair, loose clothing, ngers, and all parts

of body away from openings and moving parts.

8. Turn o all controls before removing the

battery.

9. Use extra care when cleaning on stairs.

10. Do not use to pick up ammable or combusti-

ble liquids, such as gasoline, or use in areas

where they may be present.

11. Use only the charger supplied by the manufac-

turer to recharge.

12.

Do not pick up anything that is burning or smok-

ing, such as cigarettes, matches, or hot ashes.

13. Do not use without dust bag and/or lters in

place.

14. Do not charge the battery outdoors.

15. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of re

when used with another battery pack.

16. Use appliances only with specically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and re.

17. When (the) battery pack is not in use, keep

it away from other metal objects, like paper

clips, coins, keys, nails, screws or other small

metal objects, that can make a connection

from one terminal to another.

18. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water.

19. Do not use a battery pack or appliance that

is damaged or modied. Damaged or modied

batteries may exhibit unpredictable behaviour

resulting in re, explosion or risk of injury.

20. Do not expose a battery pack or appliance

to re or excessive temperature. Exposure

to re or temperature above 130 °C may cause

explosion.

21. Follow all charging instructions and do not

charge the battery pack or appliance outside

the temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outside the specied range may damage the

battery and increase the risk of re.

SAVE THESE INSTRUCTIONS.

ADDITIONAL SAFETY RULES

This appliance is intended for household use.

1. Read this instruction manual and the charger

instruction manual carefully before use.

2. Do not pick up the following materials:

— Hot materials such as lit cigarettes or

spark/metal dust generated by grinding/

cutting metal

— Flammable materials such as gasoline,

thinner, benzine, kerosene or paint

— Explosive materials like nitroglycerin

— Ignitable materials such as Aluminum,

zinc, magnesium, titanium, phosphorus

or celluloid

— Wet dirt, water, oil or the like

— Hard pieces with sharp edges, such as

wood chips, metals, stones, glasses,

nails, pins or razors

— Powder to clot such as cement or toner

— Conductive dust such as metal or carbon

— Fine particle like concrete dust

Such action may cause re, injury and/or prop-

erty damage.

3. Stop operation immediately if you notice any-

thing abnormal.

4. If you drop or strike the cleaner, check it care-

fully for cracks or damage before operation.

Do not bring close to stoves or other heat sources.

6. Do not block the intake hole or vent holes.

SAVE THESE INSTRUCTIONS.

11 ENGLISH

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper with the battery

cartridge. It may result in a re, excessive heat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re, excessive heat, or explosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask o open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliant products may result in a re, exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may cause heating, catching re,

burst and malfunction of the tool or battery car-

tridge, resulting in burns or personal injury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near a high-voltage elec-

trical power lines. It may result in a malfunction

or breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

12 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

CAUTION: Take care not to trap nger(s)

between cleaner and battery as shown in diagram

when loading battery. Trapping nger(s) may cause

injury.

► Fig.1

Installing or removing battery cartridge

CAUTION: Always switch o the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridge rmly may cause them to slip o your hands

and result in damage to the tool and battery cartridge

and a personal injury.

► Fig.2: 1. Red indicator 2. Button 3. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator as

shown in the gure, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

it may accidentally fall out of the tool, causing injury to

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts o power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions.

Overloaded:

The tool/battery is operated in a manner that causes it

to draw an abnormally high current.

In this situation, turn the tool o and stop the application

that caused the tool to become overloaded. Then turn

the tool on to restart.

If the tool does not start, the battery is overheated. In

this situation, let the battery cool before turning the tool

on again.

Low battery voltage:

The remaining battery capacity is too low and the tool

will not operate. In this situation, remove and recharge

the battery.

Protections against other causes:

Protection system is also designed for other causes

that could damage the tool and allows the tool to stop

automatically. Take all the following steps to clear the

causes, when the tool has been brought to a temporary

halt or stop in operation.

Turn the tool o, and then turn it on again to restart.

2. Charge the battery(ies) or replace it/them with

recharged battery(ies).

3. Let the tool and battery(ies) cool down.

If no improvement can be found by restoring protection

system, then contact your local Makita Service Center.

Indicating the remaining battery capacity

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

► Fig.3: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may dier slightly

from the actual capacity.

NOTE: The rst (far left) indicator lamp will blink when

the battery protection system works.

Switch action

► Fig.4:

1. Suction power change button 2. ON/OFF button

To start the cleaner, simply push the ON/OFF button. To

switch o, push the ON/OFF button again.

You can change the suction power of the cleaner in

four steps by pushing the suction power change button.

Each push on this button repeats the Quiet/Normal/

High/Max mode in a cycle.

Level Indication Mode

1Quiet mode

Normal speed mode

3High speed mode

4Max speed mode

13 ENGLISH

NOTE: You can change the suction power before

turning on the cleaner.

NOTE: The cleaner starts the operation with the

same suction power as the last operation.

Lighting up the lamp

CAUTION: Do not look in the light or see the

source of light directly.

To turn on the lamp, push the suction power change

button. The lamp goes o in approximately 10 seconds.

While the cleaner is running, the lamp turns on.

The lamp goes out approximately 10 seconds after

stopping operation.

NOTE: When the remaining battery capacity gets low,

the lamp starts blinking. The timing, at which the lamp

starts blinking depends on the temperature at work

place and the battery cartridge conditions.

► Fig.5: 1. Suction power change button 2. ON/OFF

button 3. Lamp

ASSEMBLY

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before carrying out any work on the tool.

Dust bag and paper lter

Install either dust bag or paper lter before using cleaner.

Use the dust stopper when installing either dust bag or paper lter.

Dust bag are usable many times repeatedly by cleaning it out.

Paper lter is a throw-away type. Throw away the entire

paper lter without emptying when it has become full.

NOTICE: To prevent dust from getting into the

motor:

• Make sure that the dust bag or paper lter is

installed before use.

• Insert the dust stopper together with the

dust bag or paper lter all the way into the

slots when installing them.

• Do not use a broken or ripped bag.

Otherwise the motor may be broken.

NOTICE: Do not fold the cardboard at its open-

ing when installing the paper lter.

NOTICE: Never throw away the dust stopper

because it needs to be used repeatedly whenever

either the dust bag or the paper lter is used.

NOTICE: The paper lter for the cleaner is an

important component for maintaining the tool

performance. Using other than the genuine paper

lter may cause smokes or ignition.

NOTE: When the dust bag or the paper lter is not

installed in the cleaner, the front cover does not close

completely.

► Fig.6

Installing dust bag

Use the dust stopper when installing dust bag. Be

careful not to take the upper side for the lower side by

mistake because they are dierent each other.

► Fig.7: 1. Upper side of dust stopper 2. Lower side of

dust stopper

1. Insert the protrusion of the dust bag into the lower

groove on the dust stopper as shown in the gure.

► Fig.8: 1. Dust stopper 2. Lower groove 3. Dust bag

There is no distinction between the upper and lower

sides of the dust bag. You may insert its protrusion of

either side into the lower groove of the dust stopper.

► Fig.9: 1. Lower groove

Overlap the frame of dust stopper with that of the dust bag.

► Fig.10

3. Place the dust stopper and the dust bag together

into the cleaner cavity in the same direction of arrow on

the dust stopper. Insert them all the way into the slots in

the cleaner cavity.

► Fig.11

Spread the cloth part of the dust bag inside the cleaner.

► Fig.12

5. Close the front cover completely.

► Fig.13: 1. Front cover

Installing the paper lter

Use the dust stopper also when installing paper lter.

Be careful not to take the upper side for the lower side

by mistake because they are dierent each other.

► Fig.14: 1. Upper side of dust stopper 2. Lower side

of dust stopper

1. Unfold the entrance of the paper lter before

setting it on the dust stopper.

► Fig.15

2. Insert the protrusion of the paper lter into the

lower groove on the dust stopper as shown in the gure.

► Fig.16: 1. Dust stopper 2. Lower groove 3. Paper

lter

There is no distinction between the upper and lower

sides of the paper lter. You may insert its protrusion of

any side into the lower groove of the dust stopper.

► Fig.17: 1. Lower groove

3. Overlap the frame of dust stopper with that of the

paper lter.

► Fig.18

4. Place the dust stopper and the paper lter

together into the cleaner cavity in the same direction of

arrow on the dust stopper. Insert them all the way into

the slots in the cleaner cavity.

► Fig.19

5. Spread the container part of the paper lter inside

the cleaner.

► Fig.20

6. Close the front cover completely.

► Fig.21: 1. Front cover

14 ENGLISH

OPERATION

CAUTION: Do not move your face close to

the air vent when operating the cleaner. If foreign

objects are blown into eyes, it may result in personal

injury.

Installing and removing cleaner

attachments

CAUTION: After installing attachments, check

if they are securely installed. If the attachments are

installed imperfectly, they may come o and cause

personal injury.

CAUTION: Be careful not to hit your hand on

the wall etc. when removing the attachments.

When using attachment with lock

function

To install attachment, insert it to the suction inlet of the

cleaner until it clicks. Make sure that the attachment is

locked.

► Fig.22: 1. Suction inlet 2. Attachment with lock

function 3. Hook

NOTICE: When installing the attachment with

lock function, be sure to align the release button

on the cleaner with the hook on the attachment. If

they are not aligned, the attachment will not be locked

and may come o from the cleaner.

To remove, pull the attachment while pushing the

release button.

► Fig.23: 1. Release button 2. Attachment with lock

function

When using attachment without lock

function

NOTICE: To connect attachment without lock

function, twist and insert it securely into the suc-

tion inlet of the cleaner. To disconnect the attach-

ment, pull it away while twisting.

► Fig.24

Cleaning (Suction)

Nozzle

Attach the nozzle to clean o tables, desks, furniture,

etc. The nozzle slips on easily.

► Fig.25: 1. Nozzle

Nozzle + Extension wand (Straight pipe)

The extension wand ts in between the nozzle and the

cleaner itself. This arrangement is convenient for clean-

ing a oor in a standing position.

► Fig.26: 1. Cleaner body 2. Extension wand

3. Nozzle

Corner nozzle

Fit on the corner nozzle for cleaning corners and crev-

ices of a car or furniture.

► Fig.27: 1. Corner nozzle 2. Cleaner body

You can store the corner nozzle in the nozzle holder.

► Fig.28: 1. Nozzle holder 2. Corner nozzle

CAUTION: Be careful not to trap nger(s)

between the corner nozzle and the nozzle holder.

Trapping nger(s) may cause injury.

Corner nozzle + Extension wand

(Straight pipe)

In tight quarters where the cleaner itself cannot

squeeze in, or in high places hard to reach, use this

arrangement.

► Fig.29: 1. Corner nozzle 2. Extension wand

3. Cleaner body

Cleaning without nozzle

You can pick up powder and dust without nozzle.

► Fig.30

For picking up dust on a oor in a standing position, it is

convenient to attach the extension wand (straight pipe)

to the cleaner.

► Fig.31: 1. Extension wand (Straight pipe)

Disposing of dust

CAUTION: Empty the cleaner before it

becomes too full, or the suction force weakens.

CAUTION: When closing the front cover, be

careful not to pinch your ngers.

NOTICE: Never throw away the dust stopper

because it should be used whenever either the

dust bag or the paper lter is used.

NOTICE: When the dust bag/paper lter is not

inside of the cleaner, the front cover does not

close completely. Do not force to close the front

cover. It may result in deforming or breakage of

the tool.

NOTICE: When disposing of dust, also clean the

room for the dust bag/paper lter. The remaining

dust and dirt in the room may cause the sponge lter

to be clogged or the motor to be damaged.

1. Push the button to open the front cover. Opening

it until a click is heard allows a positive stop at that

position.

► Fig.32: 1. Front cover 2. Button

2. Pull out both the orange-colored dust stopper and

dust bag/paper lter together at the same time.

► Fig.33: 1. Dust stopper

15 ENGLISH

3. Perform the procedures below depending on the

dust container type:

When using the dust bag

Remove the dust stopper and empty the dust bag.

► Fig.34: 1. Dust stopper 2. Dust bag

When using the paper lter

Remove the dust stopper and dispose of the paper lter.

► Fig.35: 1. Dust stopper 2. Paper lter

4. Place the dust bag/new paper lter and dust stop-

per together into the cleaner and close the front cover.

NOTE: The cleaner is constructed in such a way that

the front cover comes o when trying to force the

front cover open at the angle of more than 90°. If the

front cover comes o, insert it into the front cover joint

in place.

► Fig.36: 1. Front cover 2. Front cover joint

MAINTENANCE

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

To maintain product SAFETY and RELIABILITY,

repairs, any other maintenance or adjustment should

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

After use

CAUTION: Putting the cleaner against the

wall without any other support may cause the

cleaner to fall down, resulting in personal injury

or damage to the cleaner.

► Fig.37

Cleaning

CAUTION: Clean dust bags and lters when

they become clogged. Continued use in the clogged

condition may result in heating or re.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

NOTICE: Do not blow dust sticking on the

cleaner and lters by air duster. It brings dust into

the housing and causes failure.

NOTICE: After washing dust bags and

sponge lters, dry them thoroughly before use.

Insuciently dried lters may cause poor suction and

shorten the service life of the motor.

NOTICE: After cleaning dust bags and sponge

lters, be sure to re-install them before use. If

you use the cleaner without dust bags and sponge

lters, dust comes into the motor housing and cause

malfunction.

Cleaner body

From time to time wipe o the outside (cleaner body) of

the cleaner using a cloth dampened in soapy water.

Clean out also the suction opening, dust bag/paper lter

mounting area and the dust stopper.

► Fig.38

Dust bag

Wash the dust bag in soapy water when it is clogged

with dust and the cleaner power becomes weak. Dry it

out thoroughly before use. An insuciently dried lter

may cause poor suction and shorten the service life of

the motor.

► Fig.39

NOTE: Paper lter is a throw-away type.

Dust stopper

Wipe dust o from the dust stopper.

Remove dust and dirt on the sponge part by lightly

tapping it.

► Fig.40: 1. Sponge part

Removing and installing the sponge

lter

CAUTION: After cleaning sponge lter, be

sure to install it on the cleaner. If washed in water,

dry it up before installing. An insuciently dried

sponge lter may shorten the service life of the motor.

When the sponge lter is clogged with dust, remove it

from the cleaner and then wipe it o or wash in water.

To remove the sponge lter, remove the dust bag or

paper lter and then pinch and take the sponge lter

out.

► Fig.41: 1. Sponge lter

Press in the whole edge of the sponge lter against the

recessed wall inside the dust bag/paper lter mounting

area.

► Fig.42: 1. Recessed wall

Wall mount for cordless cleaner

Optional accessory

NOTE: The screw to mount the holder is not included.

Prepare a screw which ts with the material to screw

into.

Attach the wall mount for cordless cleaner to a hard

wooden wall, beam or column, where the wall mount

for cordless cleaner can be rmly secured. Always be

sure that the wall mount for cordless cleaner is securely

attached before hanging the cleaner.

► Fig.43: 1. Wall mount for cordless cleaner

CAUTION: Do not hang the cleaner to the wall

mount violently or hang other appliances than the

cleaner.

16 ENGLISH

Troubleshooting

Before asking for repairs, check the following points.

Symptom Area to be investigated Fixing method

Weak suction power

Is dust bag or paper lter full of dust? Empty dust bag or paper lter.

Is dust bag or sponge lter clogged? Dust down or wash dust bag and sponge

lter.

Is paper lter clogged? Replace paper lter.

Is battery cartridge discharged? Charge battery cartridge.

Not working Is battery cartridge discharged? Charge battery cartridge.

Abnormal noise and vibration come

out

Is dust bag or sponge lter clogged? Dust down or wash dust bag and sponge

lter.

Is paper lter clogged? Replace paper lter.

Anything to block openings or holes? Clean any dust and objects out of nozzles,

pipes and air openings.

Is suction inlet of nozzle or pipe closed? Uncover and open suction inlet of nozzle

and pipe.

Dust case cover does not close Is dust bag or paper lter set? Set dust bag or paper lter.

CAUTION: Do not attempt to repair the cleaner by yourself.

OPTIONAL

ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or attachment

for its stated purpose.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service

Center.

• Extension wand (Straight pipe)

• Nozzle

• Nozzle for carpet

• Shelf brush

• Corner nozzle

• Round brush

• Flexible hose

• Dust bag

• Paper lter

• Free nozzle

• Seat nozzle

• Crevice nozzle

• Wall mount for cordless cleaner

• Cyclone attachment

• Tool bag

• Makita genuine battery and charger

NOTE: Some items in the list may be included in the

tool package as standard accessories. They may

dier from country to country.

Cyclone attachment

► Fig.44: 1. Release button 2. Hook 3. Extension

wand (Straight pipe) 4. Cyclone attachment

5. Suction inlet

About the cyclone attachment

Using the cleaner with the cyclone attachment installed

reduces the amount of dust that enters the dust bag,

which helps to prevent the suction force from weaken-

ing. In addition, cleaning after use is also simple.

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before carrying out any work on the tool. If the

battery cartridge is left inserted, the cleaner may start

unexpectedly and result in injury.

CAUTION: Clean the mesh lter of the

cyclone attachment and the dust bag of the

cleaner unit when they become clogged.

Continued use in the clogged condition may result in

heating or smoke.

NOTICE: When the cyclone attachment is

attached, do not use the cleaner in the horizontal

or upward facing condition. Doing so may cause

the mesh lter to become clogged.

NOTICE: Always use the cleaner with the dust

bag installed, even when using the cyclone

attachment. Using the cleaner without the dust bag

installed may result in a motor malfunction.

17 ENGLISH

NOTE: Check that the cyclone attachment, cleaner,

and extension wand (straight pipe) are locked prop-

erly before use.

NOTE: Empty the dust case of the cyclone attach-

ment and the dust bag of the cleaner when dust has

accumulated. Continued use will result in weakened

suction force.

NOTE: You can also use the cyclone attachment with-

out lock function.

NOTE: To install or remove the cyclone attachment,

refer to the section "Installing and removing cleaner

attachments".

Disposing of dust

When dust has accumulated up to the full line of the

dust case, follow the procedure below and dispose of

the dust.

1. Hold the dust case rmly, press and hold the two

buttons, and remove the dust case.

► Fig.45: 1. Full line 2. Dust case 3. Button (two

locations) 4. Mesh lter

2. Dispose of the dust inside the dust case and

remove any dust and powder adhered to the surface of

the mesh lter.

3. Insert the dust case all the way until the two but-

tons lock with a click.

► Fig.46: 1. Dust case 2. Button (two locations)

CAUTION: When reassembling the dust case,

be careful not to pinch your ngers.

NOTE: Check that the cyclone attachment, cleaner,

and extension wand (straight pipe) are locked prop-

erly before restarting operation.

NOTE: If the suction force does not recover even

after disposing of the dust and cleaning the mesh

lter, check whether dust has accumulated in the dust

bag of the cleaner or clogging has occurred.

NOTE: The dust may y up when disposing from the

cyclone attachment. Be careful not to let dust get into

your eyes.

Cleaning

CAUTION: After washing the cyclone attach-

ment, dry it thoroughly before use. Insuciently

dried components may cause an electrical shock or

damage to the appliance.

When the dust case becomes dirty or the mesh lter is

clogged, remove and wash them with water. (Refer to

“Disposing of dust” for the removal procedure.)

Dry the parts thoroughly before reinstallation and use.

► Fig.47: 1. Dust case 2. Mesh lter

When the mesh lter gets dirty badly, clean it in the

following procedures.

1. Turn the mesh lter counterclockwise and remove

it while the hooks are unlocked.

► Fig.48: 1. Mesh lter 2. Hook

2. Remove the dust on the mesh lter and then wash

it with water. After that, dry it thoroughly.

3. Insert the mesh lter into the base while the hooks

are aligned with the port. Turn the mesh lter clockwise

until the hooks are locked with a click. Make sure that

the mesh lter is installed securely.

► Fig.49: 1. Mesh lter 2. Hook 3. Port

18 SVENSKA

SVENSKA (Originalinstruktioner)

VARNING

• Denna apparat kan användas av barn från 8 års ålder och äldre samt personer med nedsatt fysisk, sensorisk

eller mental kapacitet eller brist på erfarenhet och kunskap förutsatt att de har fått handledning eller instruktio-

ner om hur apparaten används på rätt sätt och förstår riskerna som det medför.

• Barn ska inte leka med apparaten. Rengöring och användarunderhåll ska inte utföras av barn utan tillsyn.

• Se batteriets typreferens i kapitlet ”SPECIFIKATIONER”.

• Se i avsnittet ”Montera eller demontera batterikassetten” hur du tar bort eller installerar batteriet.

• När batterikassetten ska kasseras måste den tas bort från verktyget och kasseras på ett säkert sätt. Följ lokala

föreskrifter beträande avfallshantering av batteriet.

• Om verktyget inte används under en lång tid måste batteriet tas bort från verktyget.

• Kortslut inte batterikassetten.

• Se uppgifter om lämpliga försiktighetsåtgärder vid användarunderhåll i kapitlet ”UNDERHÅLL”.

SPECIFIKATIONER

Modell: CL002G

Kapacitet med dammpåse 500 mL

med papperslter 330 mL

Kontinuerlig användning

(med batteri BL4025)

1 (tyst läge) ca 80 min

2 (normalt hastighetsläge) ca 40 min

3 (höghastighetsläge) ca 25 min

4 (maxhastighetsläge) ca 16 min

Total längd (med rör, munstycke och batteri BL4025) 1 066 mm

Märkspänning 36 V - 40 V likström max

Nettovikt 1,8 - 2,4 kg

• På grund av vårt pågående program för forskning och utveckling kan dessa specikationer ändras utan föregå-

ende meddelande.

• Specikationer kan variera mellan olika länder.

• Vikten inkluderar inte tillbehör men batterikassett(er). Den lättaste och tyngsta viktkombinationen för maskin

och batterikassett(er) visas i tabellen.

Tillgänglig batterikassett och laddare

Batterikassett BL4020* / BL4025* / BL4040* / BL4050F

* : Rekommenderat batteri

Laddare DC40RA / DC40RB / DC40RC

• Vissa av batterikassetterna och laddarna på listan ovan kanske inte nns tillgängliga i din region.

VARNING: Använd endast batterikassetter och laddare från listan ovan. Användning av andra batterikas-

setter och laddare kan orsaka personskada och/eller brand.

Symboler

Följande visar symbolerna som kan användas för

utrustningen. Se till att du förstår innebörden innan

användning.

Läs igenom bruksanvisningen.

Ett representativt batteri som kan använ-

das med den här produkten.

19 SVENSKA

Ni-MH

Li-ion

Gäller endast inom EU

P.g.a. förekomsten av farliga komponenter

i utrustningen kan avfall innehållande

elektrisk och elektronisk utrustning, acku-

mulatorer och batterier ha negativ inverkan

på miljön och människors hälsa.

Kassera inte elektriska och elektro-

niska apparater eller batterier ihop med

hushållsavfall!

I enlighet med EU-direktiven om avfall

som utgörs av eller innehåller elektrisk och

elektronisk utrustning och om batterier och

ackumulatorer och förbrukade batterier

och ackumulatorer, och dess införlivande

i nationell lagstiftning, bör förbrukad elek-

trisk och elektronisk utrustning, batterier

och ackumulatorer förvaras separat och

transporteras till en särskild uppsamlings-

plats för kommunalt avfall, som drivs i

enlighet med regelverket för miljöskydd.

Detta anges av symbolen med den över-

kryssade soptunnan på hjul som sitter på

utrustningen.

Avsedd användning

Det här redskapet är avsett för insamling av torrt damm.

SÄKERHETSVARNINGAR

Säkerhetsvarningar för sladdlös

dammsugare

VARNING: VIKTIGT! LÄS NOGGRANT igenom

alla säkerhetsvarningar och anvisningar FÖRE

ANVÄNDNING. Underlåtenhet att följa varningar

och instruktioner kan leda till elstötar, brand och/eller

allvarliga personskador.

Utsätt inte för regn. Förvara maskinen inomhus.

2. Tillåt inte att den används som en leksak.

Stor uppmärksamhet är nödvändigt när den

används i barns närhet.

3. Använd den endast enligt beskrivningen i

bruksanvisningen. Använd endast tillverka-

rens rekommenderade tillsatser.

4. Använd inte maskinen med ett skadat batteri.

Om maskinen inte arbetar som den ska, har

tappats i marken, skadats, lämnats utomhus

eller hamnat i vatten ska den skickas till

servicecentret.

5. Var inte blöt om händerna när du handskas

med maskinen.

Placera inte något föremål i öppningarna. Använd

inte dammsugaren om någon av öppningarna är

blockerade och håll den ren från damm, trådar,

hår samt allt som kan minska luftödet.

Håll hår, löst sittande kläder, ngrar och alla

kroppsdelar bort från öppningar och rörliga delar.

8. Stäng av alla kontroller innan batteriet tas bort.

9. Var extra försiktig vid rengöring av trappor.

10. Använd inte maskinen för att plocka upp

brännbara eller lättantändliga vätskor, såsom

bensin, eller använd inte maskinen på platser

där sådana vätskor förvaras.

11. Använd endast den laddare som tillverkaren

har skickat med för att ladda batteriet.

12. Plocka inte upp något som brinner eller glöder,

såsom cigaretter, tändstickor eller glödande

aska.

13. Använd inte utan dammpåse och/eller ltren

monterade på plats.

14. Ladda inte batteriet utomhus.

15. Ladda endast med den batteriladdare som

angetts av tillverkaren. En laddare som passar

en viss typ av batterier kan skapa risk för brand

när den används tillsammans med annat batteri.

16. Använd endast apparater med specikt

angivna batteripaket. Om andra batterier

används kan risken för personskada och brand

öka.

17. När batteriet inte används bör det hållas borta

från andra metallföremål så som gem, mynt,

nycklar, spik, skruv eller andra små metall-

föremål som kan skapa en anslutning mellan

batteripolerna.

18. Under hårda förhållande kan det komma

vätska ur batteriet. Undvik kontakt. Spola med

vatten om kontakt ändå råkar uppstå.

19. Använd inte ett batteripaket eller en apparat

som har skadats eller ändrats. Skadade eller

ändrade batterier kan uppföra sig opålitligt, vilket

kan leda till brand, explosion eller skaderisk.

20. Utsätt inte ett batteripaket eller en apparat för

brand eller höga temperaturer. Exponering för

eld eller temperaturer över 130 °C kan leda till

explosion.

21. Följ alla laddningsinstruktioner och ladda inte

batteripaketet eller apparaten utanför det tem-

peraturintervall som anges i instruktionerna.

Felaktig laddning, eller vid temperaturer utanför

det angivna intervallet, kan skada batteriet och

öka risken för brand.

SPARA DESSA ANVISNINGAR.

YTTERLIGARE

SÄKERHETSANVISNINGAR

Denna maskin är avsedd för att användas i hushåll.

1. Läs denna bruksanvisning och laddarens

bruksanvisning noggrant innan du använder

dammsugaren.

2. Plocka inte upp följande material:

— Varmt material som tända cigaretter eller

gnist-/metalldamm som skapas när man

slipar/sågar i metall

— Lättantändliga material som bensin, thin-

ner, fotogen eller färg

— Explosivt material som nitroglycerin

— Antändbart material såsom aluminium,

zink, magnesium, titan, fosfor eller

celluloid

— Blöt smuts, vatten, olja eller liknande

— Hårda bitar med vassa kanter som träi-

sor, metaller, stenar, glas, spikar, stift

eller rakblad

— Pulver som klumpar ihop sig såsom

cement eller toner

20 SVENSKA

— Ledande damm som metall eller kol

— Fina korn som betongdamm

Att göra detta kan orsaka brand, skada och/

eller skada på egendom.

3. Stanna maskinen omedelbart om du lägger

märke till något onormalt.

4. Om du tappat eller stött till dammsugaren,

kontrollera att den inte har skadats innan du

använder den.

5. Använd inte dammsugaren nära kaminer eller

andra värmekällor.

6. Blockera inte intagshålet eller

ventilationshålen.

SPARA DESSA ANVISNINGAR.

Viktiga säkerhetsanvisningar för

batterikassetten

1. Innan batterikassetten används ska alla

instruktioner och varningsmärken på (1) bat-

teriladdaren, (2) batteriet och (3) produkten

läsas.

2. Montera inte isär eller mixtra med batterikas-

setten. Det kan leda till brand, överdriven värme

eller explosion.

3. Om drifttiden blivit avsevärt kortare ska

användningen avbrytas omedelbart. Det kan

uppstå överhettning, brännskador och t o m en

explosion.

4. Om du får elektrolyt i ögonen ska de sköljas

med rent vatten och läkare uppsökas omedel-

bart. Det nns risk för att synen förloras.

5. Kortslut inte batterikassetten.

(1) Rör inte vid polerna med något strömfö-

rande material.

(2) Undvik att förvara batterikassetten till-

sammans med andra metallobjekt som

t.ex. spikar, mynt o.s.v.

(3) Skydda batteriet mot vatten och regn.

En batterikortslutning kan orsaka ett

stort strömöde, överhettning, brand och

maskinhaveri.

6. Förvara och använd inte verktyget och batteri-

kassetten på platser där temperaturen kan nå

eller överstiga 50 °C.

7. Bränn inte upp batterikassetten även om

den är svårt skadad eller helt utsliten.

Batterikassetten kan explodera i öppen eld.

Spika inte i, krossa, kasta, tappa eller slå batteri-

kassetten mot hårda föremål. Dylika händelser kan

leda till brand, överdriven värme eller explosion.

9. Använd inte ett skadat batteri.

10.

De medföljande litiumjonbatterierna är föremål

för kraven i gällande lagstiftning för farligt gods.

För kommersiella transporter (av t.ex. tredje parter

som speditionsrmor) måste de särskilda transport-

krav som anges på emballaget och etiketter iakttas.

För att förbereda den produkt som ska avsändas

krävs att du konsulterar en expert på riskmaterial.

Var också uppmärksam på att det i ditt land kan

nnas ytterligare föreskrifter att följa.

Tejpa över eller maskera blottade kontakter och

packa batteriet på sådant sätt att det inte kan röra

sig fritt i förpackningen.

11. När batterikassetten ska kasseras måste den

tas bort från maskinen och kasseras på ett

säkert sätt. Följ lokala föreskrifter beträande

avfallshantering av batteriet.

12. Använd endast batterierna med de produkter

som specicerats av Makita. Att använda bat-

terierna med ej godkända produkter kan leda till

brand, överdriven värme, explosion eller utläck-

ande elektrolyt.

13. Om maskinen inte används under en lång tid

måste batteriet tas bort från maskinen.

14. Under och efter användning kan batterikasset-

ten bli het vilket kan orsaka brännskador eller

lättare brännskador. Var uppmärksam på hur

du hanterar varma batterikassetter.

15. Vidrör inte verktygets kontakter direkt efter

användning eftersom de kan bli heta och

orsaka brännskador.

16. Låt inte isor, damm eller smuts fastna i kon-

takterna, i hål eller spår i batterikassetten. Det

kan leda till att verktyget eller batterikassetten

värms upp, fattar eld, går sönder eller inte fung-

erar som de ska, vilket kan orsaka brännskador

eller personskador.

17. Såvida inte verktyget stöder arbeten i närheten

av högspänningsledningar får batterikassetten

inte användas i närheten av en högspännings-

ledning. Det kan leda till att verktyget eller batteri-

kassetten går sönder eller inte fungerar korrekt.

18. Förvara batteriet utom räckhåll för barn.

SPARA DESSA ANVISNINGAR.

FÖRSIKTIGT: Använda endast äkta Makita-

batterier. Användning av oäkta Makita-batterier eller

batterier som har manipulerats kan leda till person-

och utrustningsskador eller till att batteriet fattar eld.

Det upphäver också Makitas garanti för verktyget och

laddaren.

Tips för att uppnå batteriets max-

imala livslängd

1. Ladda batterikassetten innan den är helt

urladdad. Stanna alltid maskinen och ladda

batterikassetten när du märker att maskinen

blir svagare.

2. Ladda aldrig en fulladdad batterikassett.

Överladdning förkortar batteriets livslängd.

3. Ladda batterikassetten vid en rumstemperatur

på 10 °C - 40 °C. Låt en varm batterikassett

svalna innan den laddas.

4. När batterikassetten inte används ska den tas

bort från verktyget eller laddaren.

5. Ladda batterikassetten om du inte har använt

den på länge (mer än sex månader).

Leht laadib ...

Makita CL002G Kasutusjuhend

Bränd: Makita

Mudel: CL002G

Tüüp: Kasutusjuhend

Laadige alla PDF

aruanne

teistes keeltes

svenska: Makita CL002G Användarmanual
dansk: Makita CL002G Brugermanual

Seotud paberid

Muud dokumendid

Oneida Air Systems AKD000000 paigaldusjuhend