Makita HR007G Cordless Combination Hammer Kasutusjuhend

Bränd: Makita

Mudel: HR007G Cordless Combination Hammer

Kategooria: Pöördhaamrid

Tüüp: Kasutusjuhend

HR007G

EN Cordless Combination

Hammer INSTRUCTION MANUAL 11

SV Batteridriven

kombinationshammare BRUKSANVISNING 25

NO Batteridrevet

kombinasjonshammer BRUKSANVISNING 39

FI Akkukäyttöinen

yhdistelmäpora KÄYTTÖOHJE 53

DA Akku-kombinationshammer BRUGSANVISNING 67

LV Bezvadu kombinētais veseris LIETOŠANAS INSTRUKCIJA 81

LT Belaidis kombinacinis

gręžtuvas NAUDOJIMO INSTRUKCIJA 95

ET Juhtmeta

kombinatsioonihaamer KASUTUSJUHEND 109

RU Аккумуляторный

трехрежимный перфоратор РУКОВОДСТВО ПО

ЭКСПЛУАТАЦИИ 123

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

Fig.16

Fig.17

Fig.18

Fig.19

Fig.20

Fig.21

Fig.22

Fig.23

Fig.24

Fig.25

Fig.26

Fig.27

Fig.28

Fig.29

Fig.30

Fig.31

Fig.32

Fig.33

Fig.34

Fig.35

Fig.36

Fig.37

Fig.38

Fig.39

Fig.40

Fig.41

Fig.42

Fig.43

Fig.44

Fig.45

Fig.46

Fig.47

Fig.48

Fig.49

Fig.50

Fig.51

Fig.52

Fig.53

Fig.54

Fig.55

Fig.56

Fig.57

Fig.58

Fig.59

Fig.60

Fig.61

Fig.62

Fig.63

Fig.64

11 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: HR007G

Capacities Concrete 28 mm

Core bit 54 mm

Diamond core bit (dry type) 65 mm

Steel 13 mm

Wood 32 mm

No load speed 0 - 980 min-1

Blows per minute 0 - 5,000 min-1

Rated voltage D.C. 36 V - 40 V max

Overall length with BL4025 458 mm

with BL4040 473 mm

Net weight 3.8 - 4.8 kg

Optional accessory

Model: DX15

Suction performance 290 l/min

Operating stroke Up to 190 mm

Suitable drill bit Up to 260 mm

Net weight 1.3 kg

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsmaydierfromcountrytocountry.

• Theweightmaydierdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL4020* / BL4025* / BL4040* / BL4050F

* : Recommended battery

Charger DC40RA / DC40RB / DC40RC

•

Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

andchargersmaycauseinjuryand/orre.

Recommended cord connected power source

Portable power pack PDC01 / PDC1200

• The cord connected power source(s) listed above may not be available depending on your region of residence.

• Before using the cord connected power source, read instruction and cautionary markings on them.

Intended use

The tool is intended for hammer drilling and drilling in

brick, concrete and stone as well as for chiselling work.

It is also suitable for drilling without impact in wood,

metal, ceramic and plastic.

Noise

The typical A-weighted noise level determined accord-

ing to EN60745-2-6:

Model HR007G

Sound pressure level (LpA) : 94 dB(A)

Sound power level (LWA) : 105 dB (A)

Uncertainty (K) : 3 dB(A)

Model HR007G with DX15

Sound pressure level (LpA) : 93 dB(A)

Sound power level (LWA) : 104 dB (A)

Uncertainty (K) : 3 dB(A)

12 ENGLISH

NOTE:

The declared noise emission value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE:

The declared noise emission value(s) may

also be used in a preliminary assessment of exposure.

WARNING: Wear ear protection.

WARNING:

The noise emission during actual

use of the power tool can dier from the declared

value(s) depending on the ways in which the tool is

used especially what kind of workpiece is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

o and when it is running idle in addition to the

trigger time).

Vibration

The following table shows the vibration total value

(tri-axial vector sum) determined according to applica-

ble standard.

Work mode Vibration

emission

Uncer-

tainty (K)

Applicable

standard

Hammer drilling

into concrete

(ah, HD)

7.5 m/s21.5 m/s2EN60745-2-6

Hammer drilling

into concrete

with DX15 (ah, HD)

8.1 m/s21.5 m/s2EN60745-2-6

Chiselling func-

tion with side grip

(ah, Cheq)

8.6 m/s21.5 m/s2EN60745-2-6

Drilling into metal

(ah, D)

2.8 m/s21.5 m/s2EN60745-2-1

NOTE: The declared vibration total value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also

be used in a preliminary assessment of exposure.

WARNING: The vibration emission during

actual use of the power tool can dier from the

declared value(s) depending on the ways in which

the tool is used especially what kind of workpiece

is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

o and when it is running idle in addition to the

trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listedbelowmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

CORDLESS ROTARY HAMMER

SAFETY WARNINGS

1. Wear ear protectors. Exposure to noise can

cause hearing loss.

2. Use auxiliary handle(s), if supplied with the

tool.Lossofcontrolcancausepersonalinjury.

3. Hold power tool by insulated gripping sur-

faces, when performing an operation where

the cutting accessory may contact hidden

wiring. Cutting accessory contacting a "live"

wire may make exposed metal parts of the power

tool "live" and could give the operator an electric

shock.

4. Wear a hard hat (safety helmet), safety glasses

and/or face shield. Ordinary eye or sun glasses

are NOT safety glasses. It is also highly recom-

mended that you wear a dust mask and thickly

padded gloves.

5. Be sure the bit is secured in place before

operation.

6. Under normal operation, the tool is designed

to produce vibration. The screws can come

loose easily, causing a breakdown or accident.

Check tightness of screws carefully before

operation.

7. In cold weather or when the tool has not been

used for a long time, let the tool warm up for

a while by operating it under no load. This

will loosen up the lubrication. Without proper

warm-up, hammering operation is dicult.

8. Always be sure you have a rm footing. Be

sure no one is below when using the tool in

high locations.

9. Hold the tool rmly with both hands.

10. Keep hands away from moving parts.

11. Do not leave the tool running. Operate the tool

only when hand-held.

12. Do not point the tool at any one in the area

when operating. The bit could y out and

injure someone seriously.

13. Do not touch the bit, parts close to the bit, or

workpiece immediately after operation; they

may be extremely hot and could burn your

skin.

13 ENGLISH

14. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

15. Always be sure that the tool is switched

o and the battery cartridge and the bit are

removed before handing the tool to other

person.

16. Before operation, make sure that there is no

buried object such as electric pipe, water pipe

or gas pipe in the working area. Otherwise, the

drill bit/chisel may touch them, resulting an electric

shock, electrical leakage or gas leak.

17. Do not operate the tool at no-load

unnecessarily.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper the battery

cartridge.Itmayresultinare,excessiveheat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re,excessiveheat,orexplosion.

9. Do not use a damaged battery.

10.

The contained lithium-ion batteries are subject to

the Dangerous Goods Legislation requirements.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tapeormaskoopencontactsandpackupthe

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge.Itmaycauseheating,catchingre,

burst and malfunction of the tool or battery car-

tridge,resultinginburnsorpersonalinjury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near a high-voltage elec-

trical power lines. It may result in a malfunction

or breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causingres,personalinjuryanddamage.Itwill

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

14 ENGLISH

Important safety instructions for

wireless unit

1. Do not disassemble or tamper with the wire-

less unit.

2. Keep the wireless unit away from young chil-

dren. If accidentally swallowed, seek medical

attention immediately.

3. Use the wireless unit only with Makita tools.

4. Do not expose the wireless unit to rain or wet

conditions.

5. Do not use the wireless unit in places where

the temperature exceeds 50 °C (122 °F).

6. Do not operate the wireless unit in places

where medical instruments, such as heart

pace makers are nearby.

7. Do not operate the wireless unit in places

where automated devices are nearby. If oper-

ated, automated devices may develop malfunction

or error.

8. Do not operate the wireless unit in places

under high temperature or places where

static electricity or electrical noise could be

generated.

9. The wireless unit can produce electromagnetic

elds (EMF) but they are not harmful to the

user.

10. The wireless unit is an accurate instrument. Be

careful not to drop or strike the wireless unit.

11. Avoid touching the terminal of the wireless

unit with bare hands or metallic materials.

12. Always remove the battery on the product

when installing the wireless unit into it.

13. When opening the lid of the slot, avoid the

place where dust and water may come into the

slot. Always keep the inlet of the slot clean.

14. Always insert the wireless unit in the correct

direction.

15. Do not press the wireless activation button

on the wireless unit too hard and/or press the

button with an object with a sharp edge.

16. Always close the lid of the slot when

operating.

17. Do not remove the wireless unit from the slot

while the power is being supplied to the tool.

Doing so may cause a malfunction of the wireless

unit.

18. Do not remove the sticker on the wireless unit.

19. Do not put any sticker on the wireless unit.

20. Do not leave the wireless unit in a place where

static electricity or electrical noise could be

generated.

21. Do not leave the wireless unit in a place sub-

ject to high heat, such as a car sitting in the

sun.

22. Do not leave the wireless unit in a dusty or

powdery place or in a place corrosive gas

could be generated.

23. Sudden change of the temperature may bedew

the wireless unit. Do not use the wireless unit

until the dew is completely dried.

24. When cleaning the wireless unit, gently wipe

with a dry soft cloth. Do not use benzine, thin-

ner, conductive grease or the like.

25. When storing the wireless unit, keep it in the

supplied case or a static-free container.

26. Do not insert any devices other than Makita

wireless unit into the slot on the tool.

27. Do not use the tool with the lid of the slot dam-

aged. Water, dust, and dirt come into the slot may

cause malfunction.

28. Do not pull and/or twist the lid of the slot more

than necessary.Restorethelidifitcomeso

from the tool.

29. Replace the lid of the slot if it is lost or

damaged.

SAVE THESE INSTRUCTIONS.

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch o the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridgermlymaycausethemtoslipoyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator as

showninthegure,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

15 ENGLISH

Indicating the remaining battery

capacity

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

►Fig.2: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydierslightly

from the actual capacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

the battery protection system works.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem.Thissystemautomaticallycutsopowertothe

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the battery is operated in a manner that causes

it to draw an abnormally high current, the tool automat-

ically stops without any indication. In this situation, turn

thetooloandstoptheapplicationthatcausedthetool

to become overloaded. Then turn the tool on to restart.

Overheat protection

When the tool or battery is overheated, the tool stops

automatically. In this case, let the tool and battery cool

before turning the tool on again.

NOTE: When the tool is overheated, the lamp blinks.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically. In this case, remove the battery from the

tool and charge the battery.

Protections against other causes

Protection system is also designed for other causes

that could damage the tool and allows the tool to stop

automatically. Take all the following steps to clear the

causes, when the tool has been brought to a temporary

halt or stop in operation.

1. Turnthetoolo,andthenturnitonagainto

restart.

2. Charge the battery(ies) or replace it/them with

recharged battery(ies).

3. Let the tool and battery(ies) cool down.

If no improvement can be found by restoring protection

system, then contact your local Makita Service Center.

Switch action

WARNING: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

►Fig.3: 1. Switch trigger

To start the tool, simply pull the switch trigger. Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

Lighting up the front lamp

►Fig.4: 1. Lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The lamp goes out approximately 10 seconds after

releasing the switch trigger.

CAUTION: If the lamp goes o after blinking

for a few seconds, the active feedback sensing

technology is not working properly. Ask your

local Makita Service Center for repair.

NOTE:Useadryclothtowipethedirtothelensof

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

NOTE: The front lamp cannot be used while the dust

collection system (optional accessory) is installed in

the tool.

Reversing switch action

►Fig.5: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

direction of rotation before the tool stops may dam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

16 ENGLISH

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

A side for clockwise rotation or from the B side for coun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

Selecting the action mode

NOTICE: Do not rotate the action mode chang-

ing knob when the tool is running. The tool will be

damaged.

NOTICE: To avoid rapid wear on the mode

change mechanism, be sure that the action mode

changing knob is always positively located in one

of the three action mode positions.

Rotation with hammering

For drilling in concrete, masonry, etc., turn the action

mode changing knob to the symbol while pressing

the release button on the knob. Use a tungstencarbide

tipped bit (optional accessory).

►Fig.6: 1. Rotation with hammering 2. Action mode

changing knob 3. Release button

Rotation only

For drilling in wood, metal or plastic materials, turn

the action mode changing knob to the symbol while

pressing the release button on the knob. Use a twist drill

bit or wood drill bit.

►Fig.7: 1. Rotation only

Hammering only

For chipping, scaling or demolition operations, turn

the action mode changing knob to the symbol while

pressing the release button on the knob. Use a bull

point, cold chisel, scaling chisel, etc.

►Fig.8: 1. Hammering only

Hook

Optional accessory

CAUTION: Always remove the battery when

hanging the tool with the hook.

CAUTION: Never hook the tool at high loca-

tion or on potentially unstable surface.

The hook is convenient for temporarily hanging the tool.

Before installing the hook, remove the rubber cap from

the screw holes in the mounting bracket. Insert the plate

washers under the bracket, and then tighten the hook

with screws in place.

►Fig.9: 1. Rubber cap 2. Mounting bracket 3. Plate

washers 4. Hook 5. Screws

For use, lift up the arm of the hook until it snaps into the

open position.

When not in use, be sure that the hook is folded back in

the closed position.

►Fig.10: 1. Hook 2. Open position 3. Closed position

►Fig.11

Connecting lanyard (tether strap) to

the hook

CAUTION: Do not use damaged hook and

screws. Before use, always check for damages,

cracks or deformations, and make sure that the

screws are tightened.

CAUTION: Make sure that the hook is

securely installed with the screws.

CAUTION: Do not install or remove any

accessory while hanging the tool. The tool may fall

if the screws are not tightened.

CAUTION: Always use a locking carabiner

(multi-action and screw gate type) and be sure

to attach the lanyard (tether strap) to the double

looped portion of the hook. Improper attachment

may cause tool drop from the hook and result in

personalinjury.

The hook is also used for connecting the lanyard (tether

strap). Be sure to connect the lanyard (tether strap) to

the double looped portion of the hook.

►Fig.12: 1. Double looped portion of the hook

2. Lanyard (tether strap) 3. Locking cara-

biner (multi-action and screw gate type)

Safety warnings about connecting

lanyard (tether strap) to the hook

Safety warnings specic for use at height

Read all safety warnings and instructions. Failure

to follow the warnings and instructions may result in

seriousinjury.

1. Always keep the tool tethered when working

"at height". Maximum lanyard length is 2 m.

The maximum permissible fall height for lan-

yard (tether strap) must not exceed 2 m.

2. Use only with lanyards appropriate for this tool

type and rated for at least 8.0 kg.

3. Do not anchor the tool lanyard to anything on

your body or on movable components. Anchor

the tool lanyard to a rigid structure that can

withstand the forces of a dropped tool.

4. Make sure the lanyard is properly secured at

each end prior to use.

5. Inspect the tool and lanyard before each use

for damage and proper function (including

fabric and stitching). Do not use if damaged or

not functioning properly.

6. Do not wrap lanyards around or allow them to

come in contact with sharp or rough edges.

7. Fasten the other end of the lanyard outside

the working area so that a falling tool is held

securely.

8. Attach the lanyard so that the tool will move

away from the operator if it falls. Dropped tools

willswingonthelanyard,whichcouldcauseinjury

or loss of balance.

9. Do not use near moving parts or running

machinery. Failure to do so may result in a crush

or entanglement hazard.

10. Do not carry the tool by the attachment device

or the lanyard.

17 ENGLISH

11. Only transfer the tool between your hands

while you are properly balanced.

12. Do not attach lanyards to the tool in a way that

keeps switches or trigger-lock (if supplied)

from operating properly.

13. Avoid getting tangled in the lanyard.

14. Keep lanyard away from the drilling area of the

tool.

15. Use a locking carabiner (multi-action and

screw gate type). Do not use single action

spring clip carabiners.

16. In the event the tool is dropped, it must be

tagged and removed from service, and should

be inspected by a Makita Factory or Authorized

Service Center.

Torque limiter

NOTICE: As soon as the torque limiter actuates,

switch o the tool immediately. This will help pre-

vent premature wear of the tool.

NOTICE: Drill bits such as hole saw, which tend

to pinch or catch easily in the hole, are not appro-

priate for this tool. This is because they will cause

the torque limiter to actuate too frequently.

The torque limiter will actuate when a certain torque

level is reached. The motor will disengage from the

output shaft. When this happens, the drill bit will stop

turning.

Electronic function

The tool is equipped with the electronic functions for

easy operation.

• Electric brake

This tool is equipped with an electric brake. If the

tool consistently fails to quickly cease to function

after the switch trigger is released, have the tool

serviced at a Makita service center.

• Constant speed control

The speed control function provides the constant

rotation speed regardless of load conditions.

• Active Feedback sensing Technology

If the tool is swung at the predetermined accelera-

tion during operation, the motor is forcibly stopped

to reduce the burden on the wrist.

NOTE: This function does not work if the acceleration

does not reach the predetermined one when the tool

is swung.

NOTE: If the bit is swung at the predetermined

acceleration during chipping, scaling, or demolishing,

the motor is forcibly stopped. In this case, release

the switch trigger, and then pull the switch trigger to

restart the tool.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before carrying out any work on the tool.

Side grip (auxiliary handle)

CAUTION: Always use the side grip to ensure

safe operation.

CAUTION: After installing or adjusting the

side grip, make sure that the side grip is rmly

secured with its retaining projections fully

engaged by the positioning recesses on the gear

housing.

To install the side grip, follow the steps below.

1. Loosen the thumb screw on the side grip. Then

install the side grip over the barrel neck of the gear

housing.

►Fig.13: 1. Side grip 2. Thumb screw 3. Barrel neck

of the gear housing 4.Retainingprojection

5. Positioning recess

The attachment ring can be enlarged by pressing

the thumb screw down so that the ring is easily and

securely engaged over the barrel neck of the gear

housing.

►Fig.14: 1. Thumb screw 2. Attachment ring

2. Tighten the thumb screw to secure the grip at your

desired angle.

Grease

Optional accessory

Coat the shank end of the drill bit beforehand with a

small amount of grease (about 0.5 - 1 g).

This chuck lubrication assures smooth action and lon-

ger service life.

Installing and removing drill bit

Clean the shank end of the drill bit and apply grease

before installing the drill bit.

►Fig.15: 1. Shank end 2. Grease

Place the shank end of the drill bit into the chuck, and

insert it further into the chuck while hand-turning the

drillbitsotheshankendwelltsintothechuckslotand

becomes fully engaged.

Having installed the drill bit, try pulling it back to ensure

it is securely held in place.

►Fig.16: 1. Drill bit 2. Chuck

To remove the drill bit, push the chuck cover down all

the way and pull the drill bit out.

►Fig.17: 1. Drill bit 2. Chuck cover

18 ENGLISH

Chisel angle (when chipping,

scaling or demolishing)

The chisel can be secured at the desired angle. Switch

the action mode changing knob to the O symbol, and

then turn the chisel to your desired angle.

►Fig.18: 1. Action mode changing knob 2. O symbol

Switch the action mode changing knob to the sym-

bol. Try hand-turning the chisel to ensure it is securely

held in place.

Depth gauge

The depth gauge is convenient for drilling holes of

uniform depth.

Press and hold the lock button, and then insert the

depth gauge into the hex hole. Make sure that the

toothed side of the depth gauge faces the toothed mark-

ing on the hex hole.

►Fig.19: 1. Depth gauge 2. Lock button 3. Hex hole

4. Toothed side 5. Toothed marking

Adjustthedepthgaugebymovingitbackandforth

whilepressingthelockbutton.Aftertheadjustment,

release the lock button to lock the depth gauge.

NOTE: Make sure that the depth gauge does not

touch the main body of the tool when attaching it.

Dust collection system

Optional accessory

Installation

1. Slide the air duct cap out of the motor housing

while lifting the lock tab up to the unlocked position.

►Fig.20: 1. Air duct cap 2. Lock tab

2. Mount the tool onto the dust collection system by

sliding the guide grooves on bottom surface of the gear

housing over the guide rails on top surface of the dust

collection system until it locks in place with a click.

►Fig.21: 1. Guide grooves 2. Guide rails 3. Dust

collection system

Uninstallation

1. Dismount the tool from the dust collection system

byslidingthetoolawayowhilepressingthelocko

button on the dust collection system.

►Fig.22: 1. Dust collection system 2.Lockobutton

2. Slide the air duct cap back along the guide

grooves on gear housing until it locks in place with a

click.

►Fig.23: 1. Air duct cap 2. Guide grooves

NOTICE: Make sure to place the air duct cap

back over the air duct after detaching the dust

collection system from the tool. Tool performance

canbeaectedifitisoperatedwithouttheairduct

cap in place.

Adjusting nozzle position

Slideinandoutthenozzleguidewhilepressingtheguideadjust-

ment button, and then release the button at an exact position where

thetipofthedrillbitsitsjustbehindthefrontsurfaceofthenozzle.

►Fig.24: 1. Nozzle guide 2.Guideadjustmentbutton

3. Tip of drill bit 4. Front surface of nozzle

NOTE:Beforeadjustingthenozzleposition,press

theguideadjustmentbuttontoreleasethetensionon

the nozzle guide and set it free into a fully extended

position.

Adjusting drilling depths

Drillingdepthcanbeadjustedbychangingthelengths

betweenthedepthadjustmentbuttonandrearendof

thenozzleguide.Pressandholdthedepthadjustment

button and slide it to your desired position.

►Fig.25: 1.Depthadjustmentbutton2. Nozzle guide

3. Drilling depths

Storage

NOTICE: When not in use for a certain period of

time, the nozzle guide needs to be extended to

approximately 100 mm from its fully shortened

position. Failing to do so may damage the duct hose

pre-installed in the nozzle guide.

►Fig.26: 1.Guideadjustmentbutton2. Approx.

100 mm

Dust cup

Optional accessory

Use the dust cup to prevent dust from falling over the tool and

on yourself when performing overhead drilling operations.

Attachthedustcuptothebitasshowninthegure.Thesize

of bits which the dust cup can be attached to is as follows.

Model Bit diameter

Dust cup 5 6 mm - 14.5 mm

Dust cup 9 12 mm - 16 mm

►Fig.27: 1. Dust cup

Dust cup set

Optional accessory

CAUTION: Before installing and uninstalling

the dust cup set, remove a bit from the tool.

Installation

Place the dust cup set onto the barrel neck of the gear

housing aligning the symbol on the dust cup with

one of the grooves in the barrel. Then hold the attach-

ment unit of the dust cup set and push it down onto the

barrel to secure it in place.

►Fig.28: 1. Dust cup set 2. Attachment unit

3. symbol 4. Groove

NOTE: If you connect a vacuum cleaner to the dust

cup set, remove the dust cap before connecting it.

►Fig.29: 1. Dust cap

19 ENGLISH

Uninstallation

Pushthechuckcoverdownallthewayandpullabito.

►Fig.30: 1. Bit 2. Chuck cover

Hold the attachment unit of the dust cup set and pull it

apart from the tool.

►Fig.31: 1. Attachment unit

NOTE:Ifthecapcomesofromthedustcupset,

place it back to the original position.

1. Detach the bellows from the attachment unit of the

dust cup set.

►Fig.32: 1. Bellows 2. Attachment unit

2. Set the cap back in place with its printed side

facing upwards.

►Fig.33: 1. Cap 2. Printed side 3. Grooves 4. Lips of

upper opening 5. Attachment unit

3. Besurethatthegroovesaroundthecapwelltin

the lips of the upper opening of the attachment unit.

►Fig.34

OPERATION

CAUTION: Always use the side grip (auxiliary

handle) and rmly hold the tool by both side grip

and switch handle during operations.

CAUTION: Always make sure that the work-

piece is secured before operation.

CAUTION: Do not pull the tool out forcibly

even the bit gets stuck. Loss of control may

cause injury.

CAUTION: The dust collection system is

intended for drilling in concrete only. Do not use

the dust collection system for drilling in metal or

wood.

CAUTION: When using the tool with the dust

collection system, be sure to attach the lter

to the dust collection system to prevent dust

inhalation.

CAUTION: Before using the dust collection

system, check that the lter is not damaged.

Failure to do so may cause dust inhalation.

CAUTION: The dust collection system col-

lects the generated dust at a considerable rate,

but not all dust can be collected.

NOTICE: If the tool is operated continuously at

low speed for a long time, the motor will get over-

loaded, resulting in tool malfunction.

NOTICE: Do not use the dust collection system

for core drilling or chiseling.

NOTICE: Do not use the dust collection system

for drilling in wet concrete or use this system

in wet environment. Failure to do so may cause

malfunction.

NOTE: If the battery cartridge is in low temperature,

the tool’s capability may not be fully obtained. In this

case, warm up the battery cartridge by using the

tool with no load for a while to fully obtain the tool’s

capability.

►Fig.35

Hammer drilling operation

CAUTION: There is tremendous and sudden

twisting force exerted on the tool/drill bit at the time of

hole break-through, when the hole becomes clogged

with chips and particles, or when striking reinforcing

rods embedded in the concrete. Always use the side

grip (auxiliary handle) and rmly hold the tool by

both side grip and switch handle during opera-

tions. Failure to do so may result in the loss of control

ofthetoolandpotentiallysevereinjury.

Set the action mode changing knob to the symbol.

Position the drill bit at the desired location for the hole,

then pull the switch trigger. Do not force the tool. Light

pressure gives best results. Keep the tool in position

and prevent it from slipping away from the hole.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the tool at

an idle, then remove the drill bit partially from the hole.

By repeating this several times, the hole will be cleaned

out and normal drilling may be resumed.

NOTE: Eccentricity in the drill bit rotation may occur

while operating the tool with no load. The tool auto-

matically centers itself during operation. This does not

aectthedrillingprecision.

Chipping/Scaling/Demolition

Set the action mode changing knob to the symbol.

Holdthetoolrmlywithbothhands.Turnthetoolon

and apply slight pressure on the tool so that the tool will

not bounce around, uncontrolled.

Pressing very hard on the tool will not increase the

eciency.

►Fig.36

Drilling in wood or metal

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece. There is a tremendous force exerted on

the tool/drill bit at the time of hole break through.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure workpieces in a

vise or similar hold-down device.

20 ENGLISH

NOTICE: Never use “rotation with hammering”

when the drill chuck is installed on the tool. The

drill chuck may be damaged.

Also,thedrillchuckwillcomeowhenreversingthe

tool.

NOTICE: Pressing excessively on the tool will

not speed up the drilling. In fact, this excessive

pressure will only serve to damage the tip of your drill

bit, decrease the tool performance and shorten the

service life of the tool.

Set the action mode changing knob to the symbol.

Installing drill chuck set

Optional accessory

Attach the chuck adapter to a keyless drill chuck to

which 1/2"-20 size screw can be installed, and then

install them to the tool. For details on how to install

the adapter into the chuck, refer to the instructions on

installing drill bit.

►Fig.37: 1. Keyless drill chuck 2. Chuck adapter

Diamond core drilling

NOTICE: If performing diamond core drilling

operations using “rotation with hammering”

action, the diamond core bit may be damaged.

When performing diamond core drilling opera-

tions, always set the action mode changing knob to

the position to use "rotation only" action.

Beating dust on the lter

Optional accessory

CAUTION: Do not turn the dial on the dust

case while the dust case is removed from the

dust collection system. Doing so may cause dust

inhalation.

CAUTION: Always switch o the tool when

turning the dial on the dust case. Turning the dial

while the tool is running may result in the loss of

control of the tool.

Bybeatingthedustonthelterinsidethedustcase,

youcankeepthevacuumeciencyandalsoreduce

the number of times to dispose of the dust.

Turn the dial on the dust case three times after col-

lecting every 50,000 mm3 of dust or when you feel the

vacuum performance declined.

NOTE: 50,000 mm3 of dust equivalents to drilling 10

holes of ø10 mm and 65 mm depth.

►Fig.38: 1. Dust case 2. Dial

Disposing of dust

Optional accessory

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before carrying out any work on the tool.

CAUTION: Be sure to wear dust mask when

disposing of dust.

CAUTION: Empty the dust case regularly

before the dust case becomes full. Failure to do so

may decrease the dust collection performance and

cause dust inhalation.

CAUTION: The performance of dust collection

decreases if the lter in the dust case become

clogged. Replace the lter with new one after

approximately 200 times of dust fulllment as a

guide. Failure to do so may cause dust inhalation.

1. Remove the dust case while pressing down the

latch lever of the dust case.

►Fig.39: 1. Latch lever

2. Lift the lock tab slightly outwards and open the

dust case cover.

►Fig.40: 1. Dust case cover 2. Lock tab

3. Disposeofthedust,andthencleanthelter.

►Fig.41

NOTICE: When cleaning the lter, tap the case

of the lter gently by hand to remove dust. Do not

tap the lter directly; touch the lter with brush

or similar; or blow compressed air on the lter.

Doing so may damage the lter.

Blow-out bulb

Optional accessory

After drilling the hole, use the blow-out bulb to clean the

dust out of the hole.

►Fig.42

Using dust cup set

Optional accessory

Fit the dust cup set against the ceiling when operating

the tool.

►Fig.43

NOTICE: Do not use the dust cup set when drill-

ing in metal or similar. It may damage the dust

cup set due to the heat produced by small metal

dust or similar.

NOTICE: Do not install or remove the dust cup

set with the drill bit installed in the tool. It may

damage the dust cup set and cause dust leak.

Leht laadib ...

Makita HR007G Cordless Combination Hammer Kasutusjuhend

Bränd: Makita

Mudel: HR007G Cordless Combination Hammer

Kategooria: Pöördhaamrid

Tüüp: Kasutusjuhend

Laadige alla PDF

aruanne

Makita HR007G Cordless Combination Hammer Kasutusjuhend

Makita HR007G Cordless Combination Hammer Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid