Samsung VR20R7250WC Kasutusjuhend

POWERbot

User manual

VR20R72**** Series

• Before operating this unit, please read the instructions carefully.

• For indoor use only.

1_VR7200_EN_DJ68-00827G-00_SB.indd 1 2019-03-27 오후 5:11:44

ENGLISH-02

Contents

03

Safety information

08

Installation

Accessories / Installation note

10

Charging

Automatic charging / Recharging / Low

battery (Lo)

12

Using POWERbot

Turning the power on/off / Selecting

cleaning modes/ Using special cleaning

functions / About the boundary markers

16

Using the remote controller

18

Name of each part

Top / Bottom / Display panel

19

Setting time/schedule

Setting the time / Setting the schedule

20

Cleaning and maintaining

Cleaning the dustbin / Cleaning the sensors and

the camera / Cleaning the brush and Auto shutter

tool / Cleaning the Driving wheel

22

SmartThings App

26

Notes and cautions

Charging / Using / Cleaning and maintenance /

About the battery / About the IrDA sensor

28

Information codes

29

Troubleshooting

33

Warnings about battery

34

Open Source Announcement

35

Specications

1_VR7200_EN_DJ68-00827G-00_SB.indd 2 2019-03-27 오후 5:11:45

ENGLISH-03

Safety information

SAFETY INFORMATION

WARNING

• Before operating the appliance, please read this manual thoroughly and

retain it for your reference.

WARNING

• Because these following operating instructions cover various models, the

characteristics of your vacuum cleaner may differ slightly from those

described in this manual.

CAUTION/WARNING SYMBOLS USED

WARNING

Indicates that a danger of death or serious injury exists.

CAUTION

Indicates that a risk of personal injury or material damage exists.

OTHER SYMBOLS USED

NOTE

Indicates that the following text contains additional important

information.

• For information on Samsung’s environmental commitments and product

specic regulatory obligations e.g. REACH visit: samsung.com/uk/

aboutsamsung/samsungelectronics/corporatecitizenship/data_corner.htm

1_VR7200_EN_DJ68-00827G-00_SB.indd 3 2019-03-27 오후 5:11:45

ENGLISH-04

Safety information

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should be observed, including

the following:

READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot.

Unplug from outlet when not in use and before conducting maintenance.

WARNING: to reduce the risk of re, electric shock, or injury:

GENERAL

• Use only as described in this manual.

• Do not operate POWERbot or the battery charger / docking station if it has

been damaged in any way.

• If the vacuum cleaner is not working as it should, has been dropped, damaged,

left outdoors, or dropped in water, return it to a customer care center.

• Do not handle the battery charger / docking station or POWERbot with wet

hands.

• Use only on dry, indoor surfaces.

• This appliance can be used by children aged from 8years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

• If the supply cord is damaged, it must be replaced by the manufacturer or its

service agent or a similarly qualied person in order to avoid a hazard.

Battery charger / Docking station

• Do not modify the polarized plug to t a non-polarized outlet or extension

cord.

• Do not use outdoors or on wet surfaces.

• Unplug the battery charger / docking station from the outlet when not in use

and before servicing.

• Use only the battery charger / docking station supplied by the manufacturer to

recharge.

• Do not use with a damaged cord or plug or a loose power outlet.

• Do not pull or carry by the cord, use the cord as a handle, close the door on the

cord, or pull the cord around sharp edges or corners. Keep the cord away from

heated surfaces.

1_VR7200_EN_DJ68-00827G-00_SB.indd 4 2019-03-27 오후 5:11:45

ENGLISH-05

• Do not use extension cords or outlets with inadequate current carrying

capacity.

• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

• Do not mutilate or incinerate batteries as they will explode at high

temperatures.

• Do not attempt to open the battery charger / docking station. Repairs should

only be carried out by a qualied customer care center.

• Do not expose the battery charger / docking station to high temperatures or

allow moisture or humidity of any kind to come into contact with the battery

charger / docking station.

• Do not charge the non-rechargeable batteries with the battery charger /

docking station

POWERbot

• Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc.

• Do not use without a lter in place. When servicing the unit, never put ngers

or other objects into the fan chamber in case the unit accidentally turns on.

• Do not put any objects into openings. Do not use with any openings blocked;

keep openings free of dust, lint, hair, and anything that may reduce air ow.

• Do not pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).

• Do not pick up anything that is burning or smoke, such as cigarettes, matches,

or hot ashes.

• Do not use to pick up ammable or combustible liquids such as gasoline, nor

use on areas where they may be present.

• Locations with candles or desk lamps on the oor.

• Locations with unattended res (re or embers).

• Locations with distilled alcohol, thinner, ashtrays with burning cigarettes, etc.

• Do not use POWERbot in an enclosed space lled with vapours given off by oil

based paint, paint thinner, moth proong substances, ammable dust, or other

explosive or toxic vapours.

• Leaks from battery cells can occur under extreme usage or temperature

conditions. If the liquid gets on skin, wash quickly with water. If the liquid

gets into the eyes, ush them immediately with clean water for a minimum of

10minutes. Seek medical attention.

1_VR7200_EN_DJ68-00827G-00_SB.indd 5 2019-03-27 오후 5:11:45

ENGLISH-06

WARNING

Power related

f Please prevent any risk of electric shock

or re.

– Do not damage the power cord.

– Do not pull the power cord too hard or

touch the power plug with wet hands.

– Do not use a power source other than 100-

240V~ and also do not use a multi outlet

to supply power to number of devices

at the same time. (Do not leave the cord

carelessly on the oor.)

– Do not use a damaged power plug, power

cord or loose power outlet.

f Clean dust or any foreign matters on the

pin and contact part of the power plug.

– There is a risk of electric shock or

malfunction.

WARNING

Before use

f Do not use POWERbot near a heater or

combustible materials.

– Do not use POWERbot near re or ame

such as a movable heater, a candlelight,

a desk lamp, a replace etc. or in a place

where combustible materials such as

gasoline, alcohol, thinner etc. exist.

f Make sure there are no dangerous

objects around the POWERbot’s cleaning

area to prevent collision and unplug any

electric heaters or fans.

f The POWERbot is intended for household

use therefore do not use it in an attic,

basement, storage, industrial building,

out of indoor space, places with moisture

(such as bathroom, laundry), on the table

or shelves.

– The POWERbot can be damaged or

malfunction.

f Be sure POWERbot does not pass through

or touch any kind of liquids.

– The POWERbot can be severely damaged

and it may contaminate other areas if the

wheels pass through liquid.

f Attach the boundary markers to places

where the POWERbot may fall such as

the top of a staircase or a bannister to

prevent product damage and injury.

– Please keep the cliff sensor clean at all

times for safety.

f Do not spill any liquids on the docking

station.

– There is a risk of re or electric shock.

f Do not use the docking station for

anything other than its intended purpose.

– There is a risk of re or severe damage to

the docking station.

f Always keep the cliff sensor clean for

your safety.

WARNING

In use

f If any abnormal sounds, smells or smoke

come from POWERbot, immediately shut

off the emergency switch at the bottom of

POWERbot and contact a service center.

WARNING

Cleaning and

maintenance

f When power cord is damaged, contact

a service center to get it replaced by a

certied repairman.

– There is a risk of re or electric shock.

f Please check with a Samsung Electronics

service center when exchanging batteries.

– Using batteries from other products can

cause malfunction.

CAUTION

Before use

f Insert the dustbin before using

POWERbot.

Safety information

1_VR7200_EN_DJ68-00827G-00_SB.indd 6 2019-03-27 오후 5:11:45

ENGLISH-07

f Be careful with the followings for proper

automatic recharging.

– Always turn on the power of the docking station.

– Install the docking station where

POWERbot can easily nd.

– Do not leave any object in front of the

docking station.

f When installing the docking station, do

not leave the cord carelessly on the oor

since POWERbot may get tangled by it.

f Do not use POWERbot on black colored

oors.

– The POWERbot may not be able to operate

normally.

f Do not place any objects within 0.5m

to both sides and 1m to the front of the

docking station.

f Make sure the docking station's charging

contact is not damaged or have any

foreign matters on it.

f Do not install the docking station in an

area with a dark oor.

– If the oor around the docking station is

dark, recharging is hindered.

f Move any obstacles that may disturb

POWERbot's movement (such as children's

indoor swing or slides) before cleaning.

f Do not use the POWERbot in a place

which is narrower than the turning

radius (0.5 m or less) of the POWERbot.

f To clean all areas of your house, open all

rooms and attach the boundary markers

to places where the POWERbot could get

damaged such as a front door, veranda,

bathroom, or stairs.

f For areas with low clearance where

the POWERbot may get stuck, attach

the boundary markers to prevent the

POWERbot from getting in.

f If a brush or brush cover is not assembled

correctly, scratches may occur on the

oor, or product malfunction may occur.

f Before operating the POWERbot, remove

the objects which could break such as a

frame, mirror, and porcelain items so that

the POWERbot works without interruption.

CAUTION

In use

f Using POWERbot on thick carpet may

damage both POWERbot and the carpet.

– The POWERbot cannot pass over carpet

that is thicker than 1 cm.

f Do not use POWERbot on tables or other

high surfaces.

– There is a risk of damage if it falls.

f The POWERbot may bump into chair,

desk legs therefore move them away for

faster and efcient cleaning.

f When POWERbot is operating, do not lift

it up or carry it to another area.

f Do not hold by driving wheels of

POWERbot when carrying it to another

area.

f Do not put any objects on top of

POWERbot and camera since it may

cause malfunction.

f Remove any large papers or plastic bags

immediately when using POWERbot since

they may block the intake.

f Do not aim the red pointer directly at

people or animals.

f Do not lie down around the POWERBOT

that is running.

– Your hair may be caught in the brush,

resulting in physical injury.

CAUTION

Cleaning and

maintenance

f Prevent any damage to POWERbot by

complying with the following

– Do not clean POWERbot by spraying water

directly onto it or use benzene, thinner,

acetone or alcohol to clean it.

f Do not disassemble or repair POWERbot.

This should only be done by a certied

repairman.

f Always keep the obstacle sensor, cliff

sensor and camera clean.

– If foreign matter accumulates, sensors may

malfunction.

1_VR7200_EN_DJ68-00827G-00_SB.indd 7 2019-03-27 오후 5:11:46

ENGLISH-08

DC-IN

1

Connect the

battery charger

jack to the

docking station

2

Connect the

power cord

to the battery

charger

When using the battery

charger, the side with the

sticker attached must face

down.

3

Connect the

power plug to

the outlet

Installation

The docking station must be plugged in and turned on at all times.

About 1m

About

0.5m

About

0.5m

Install the docking station in

a place without obstacles and

danger of falling.

1_VR7200_EN_DJ68-00827G-00_SB.indd 8 2019-03-27 오후 5:11:47

ENGLISH-09

Accessories

Remote controller Batteries

(AAA type)

User manual Spare lter Docking station

Power cord Battery charger Boundary markers Soft Action Brush /

Brush cover

Combo Brush /

Brush cover

 Accessories may differ depending on the models.

 Refer to page 15 for the installation of boundary markers.

 Battery Spec : Lithium-ion, 21.6V, 3600mAh, 12cell

 For VR20R726*** models, combo brush and soft action brush are provided.

Installation note

Note

f Install the docking station in a place where the oor and wall are level.

f It is best to install the docking station along the grain of wooden oors.

f If the emergency switch is off, the POWERbot will not charge even if it is docked on the

docking station.

f Always turn on the power of the docking station.

– If power is not supplied to the docking station, the POWERbot cannot nd it and cannot

automatically recharge.

– If the POWERbot is left detached from the docking station, the battery will drain naturally.

f If the POWERbot is in sleep mode, power will not come on even if the emergency switch

is turned off and then on. Press and hold the [Start/Stop] button on the POWERbot to turn

the sleep mode off.

1_VR7200_EN_DJ68-00827G-00_SB.indd 9 2019-03-27 오후 5:11:49

ENGLISH-10

Charging

1

Turn on the

emergency switch

on the bottom

You must turn on the

emergency switch to turn on

the POWERbot.

2

Manually charge

the POWERbot by

placing it on the

docking station

Make sure the charging

pins on the POWERbot

and the docking station

are aligned.

3

Check the

charging status

" " will turn on according

to charging progress and "FULL"

will turn on when charging is

complete.

WARNING

• Rated input voltage of this product is 100-240V~.

Charge the POWERbot fully before using for the rst time. (Refer to the page 35 for the charging

time.)

1_VR7200_EN_DJ68-00827G-00_SB.indd 10 2019-03-27 오후 5:11:50

ENGLISH-11

You can command the POWERbot to

recharge at the docking station while it is

in cleaning.

Recharging

Manually charge the POWERbot by placing

it on the docking station.

Low battery (Lo)

Steps to take if recharging not occuring:

Check the installation status of the

docking station when:

fthe docking station is located in a place where

the POWERbot cannot easily access it.

fthe distance between the docking station and

POWERbot is over 5m.

– It may take a long time for POWERbot to

return to the docking station for recharging

Manually charge the POWERbot when:

fthe docking station is located in a corner

fthe battery is fully exhausted

fthe POWERbot is immobilized by an obstacle

(furniture etc.)

fthe POWERbot can't climb a threshold near

the docking station (The maximum height of

a threshold the POWERbot can climb is about

1.5 cm.)

fwhen the battery indicator blinks and "Lo" is

displayed

fwhen the POWERbot is set to the Spot clean or

Manual clean mode

When the battery indicator blinks during

cleaning, the POWERbot will return

to the docking station to charge itself

automatically.

Automatic charging

1_VR7200_EN_DJ68-00827G-00_SB.indd 11 2019-03-27 오후 5:11:51

ENGLISH-12

Using POWERbot

You must turn on the emergency switch on the bottom of the unit before using POWERbot.

Turning the power on/off

Press the button for more than 3seconds

Starting Auto clean mode

The POWERbot moves and automatically cleans the

set areas only once.

 Stop cleaning: Press and release the button

Recharging

You can command POWERbot to recharge at the

docking station automatically while it is cleaning

by pressing this button.

Using Spot clean mode

The POWERbot cleans a localized area intensely.

WARNING

• When POWERbot is not used for about 30 minutes, it automatically returns to the

docking station to recharge.

1_VR7200_EN_DJ68-00827G-00_SB.indd 12 2019-03-27 오후 5:11:53

ENGLISH-13

Selecting cleaning modes

Cleaning mode How to select Displayed icon

Auto clean

Spot clean

Repeat clean

 Press the [

] on the remote controller rst

and then press the [Start/Stop

].

Manual clean

 Manual clean mode can be selected by the

direction control buttons of the remote

controller.

 If POWERbot fails to return to the docking station, it will turn to energy-saving mode and display

panel will be turned off.

 To exit the energy-saving mode, press the [Start/Stop

] or [Power ] button of main body or

remote controller.

 If cleaning in Auto clean mode is completed within 15 minutes, POWERbot cleans 1 more time.

 POWERbot increases suction power in Spot clean and Point cleaning mode.

1_VR7200_EN_DJ68-00827G-00_SB.indd 13 2019-03-27 오후 5:11:54

ENGLISH-14

Cleaning method for each modes

About 1.5 m

Auto clean

Automatically cleans the

set areas only once.

Spot clean

Cleans a localized area

intensely. It can be used

to clean bread or cookie

crumbs.

Manual clean

You can move

POWERbot with the

remote controller to

clean the desired spot.

Repeat clean

Cleans repeatedly until

the battery is depleted.

Using special cleaning functions

Cleaning function Operation Displayed icon

Intelligent power

control

 When the POWERbot detects a carpet in

normal mode, it will automatically operate with

stronger suction power.

Edge Clean Master

 When the POWERbot detects an edge or corner

in Auto clean or Spot clean, the auto shutter tool

operates and approaches the edge or corner

section to clean.

fStraight edge (One time cleaning)

fCorner (Two times cleaning)

Using POWERbot

1_VR7200_EN_DJ68-00827G-00_SB.indd 14 2019-03-27 오후 5:11:56

ENGLISH-15

About the boundary markers

To prevent the POWERbot from entering the following areas,

attach the boundary markers on the oor in the shape at an

interval of about 15cm.

About 15cm

Boundary markers

About 5cm

About 15cm

Boundary

markers

where a raised spot is below 5cm where there is a slide, swing, replace or any

ammable substance or moisture.

Above 1.5cm

boundary

markers

Boundary

markers

where a threshold is above 1.5cm where there is risk of falling such as stairs,

porches or guardrails.

1_VR7200_EN_DJ68-00827G-00_SB.indd 15 2019-03-27 오후 5:11:57

ENGLISH-16

1 Operation & Recharging

Power

Turn POWERbot's power on/off

Recharging

Select to recharge POWERbot at the

docking station automatically

Start/Stop

Select to start or stop cleaning

process

2 Cleaning modes

Auto clean

Select to clean all set areas only

once and then automatically return

to the docking station.

Spot clean

Select to clean a localized area

intensely

Repeat clean

Select to clean repeatedly until the

battery becomes very low with

indicator blinking

3 Suction power

Max mode

Select to clean with the strongest

suction power

Normal

mode

Select to clean with moderate

suction power

Quiet mode

Select to clean with lower

operation noise

4 Additional function

Sound

Select to set the voice guide

fVoice Guide (English)  Sound

Effects  Mute

fPress and hold the sound button

to change and set a language.

Remote

control

Select to turn Wi-Fi function on or

off

Using the remote controller

1

3

5

2

Refer to

page 19

4

6

1, 2

1_VR7200_EN_DJ68-00827G-00_SB.indd 16 2019-03-27 오후 5:11:59

ENGLISH-17

5 Manual clean mode & Direction control

Move forward

Select to move forward

Turn left

Select to turn left

Turn right

Select to turn right

 Moving backward is not available.

6 Point cleaning

You can use the remote controller to point and clean the desired spot while the

POWERbot is in cleaning process.

Point the red light on the oor within 0.5m around POWERbot's location.

Press and hold the Point cleaning button to move the red light to the desired spot. The POWERbot

will follow the light while cleaning.

fIf you point the red light directly at the body of the POWERbot, abnormal operation may occur.

Therefore, point the red light within 0.5 m around the POWERbot.

0.5 m

Operating distance of the remote controller

Height of the

remote controller

Operating distance

Height of the

remote controller

0.5m 1m 1.5 m

Operating

distance

About 1.5m About 2m About 3m

Inserting batteries

Open the battery cover by lifting it

up while pressing the locking tab and

insert the batteries as shown in the

illustration. Then, close the cover until

it clicks into place.

1_VR7200_EN_DJ68-00827G-00_SB.indd 17 2019-03-27 오후 5:12:02

ENGLISH-18

Name of each part

1

4

2

6

5

3

7

8

Top

1. Display panel

2. Remote control signal receiver

3. Obstacle sensor

4. Dustbin

5. Camera

6. Dustbin button

7. Bumper sensor

8. Auto shutter tool

5

4

2

3

4

11

8

4

9

10

7

1

6

Bottom

1. Charge pins

2. Brush

3. Brush cover

4. Cliff sensor

5. Roller

6. * Optical sensor

7. Battery cover

8. Brush cover button

9. Driving wheel

10. Emergency switch

11. Auto shutter tool

* Optical sensor: Measures moving distance by the light pattern which is reected from oors and

comes into the optical receiver.

5

16

15

3

4

7

1

6

2

14

12 138 11109

Display panel

1. Mute

2. Information Indicator

3. Remote control Off/On indicator

4. Wi-Fi

5. Battery indicator

6. One-time/Daily schedule

7. Number display

8. Spot clean mode

9. Manual clean mode

10. Repeat clean mode

11. Quiet mode

12. Normal mode

13. Max mode

14. Spot cleaning button

15. Start/Stop button

16. Recharging button

1_VR7200_EN_DJ68-00827G-00_SB.indd 18 2019-03-27 오후 5:12:03

ENGLISH-19

Setting time/schedule

Setting the time

You must set the current time before using the One-time/daily schedule.

Start setting Select "Hour" Select "Minute"

Select "AM/PM"Setting complete

Skip to previous,

next setting

Setting the schedule

Setting/cancelling the schedule can only be done while POWERbot is docked on the docking station.

Start setting Select "One-time" or

"Daily" schedule

Select "Hour"

Select "Minute"Select "AM/PM"Setting complete

Skip to previous, next setting

Cancelling during setup

fSetting will be canceled automatically when there's no

input for 7seconds.

Cancelling One-time/Daily schedule

When both One-time/

Daily schedule is set

or or

Press for 3 sec. Select the schedule Cancel complete

When either one of

One-time or Daily

schedule is set

Press for 3 sec.

fYou can set the multi-time schedule and the anti-disturbance time with the SmartThings App.

fWhen the anti-disturbance time is set at the SmartThings App, you cannot set the schedule at the

body of the POWERbot within the set anti-disturbance time.

– If you want to set the schedule within the set anti-disturbance time, cancel the set anti-

disturbance time at the SmartThings App rst.

1_VR7200_EN_DJ68-00827G-00_SB.indd 19 2019-03-27 오후 5:12:07

ENGLISH-20

Cleaning and maintaining

You must turn off the emergency switch before cleaning POWERbot.

Cleaning the dustbin

1

Press the button to

remove the dustbin

2

Remove the dustbin

cover

3

Remove dust in the

dustbin and cyclone

unit

'Click'

4

Detach the cyclone unit

from the dustbin cover,

and then wash the

dustbin and the lter

5

Reassemble the dustbin

6

Reinsert the dustbin

into the main body

until it clicks

Cleaning the sensors and the camera

Lightly wipe with soft cloth. Do not use water or cleaning solutions.

Camera

Front sensor

window

Rear sensor

window

Cliff

sensors

Optical

sensor

1_VR7200_EN_DJ68-00827G-00_SB.indd 20 2019-03-27 오후 5:12:11

Leht laadib ...

Samsung VR20R7250WC Kasutusjuhend

Samsung VR20R7250WC Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid