Samsung VR20R7250WC Kasutusjuhend

Tüüp
Kasutusjuhend
POWERbot
Quick reference guide
VR20R72**** Series
Before operating this unit, please read the instructions carefully.
For indoor use only.
1_VR7200_Q_guide_EN_00827G-03_SB.indd 1 2020-01-13 오후 7:53:53
English-2
Parts list
1
Main
body
Basic
Parts
Remote
controller
Docking
Station
Batteries
(AAA type)
Quick reference
guide
Spare lter Power cord
Battery Charger Boundary markers Soft Action Brush /
Brush cover
Combo Brush /
Brush cover
Accessories may differ depending on the models.
Refer to page 9 for the installation of boundary markers.
Battery Spec : Lithium-ion, 21.6V, 3600mAh, 12cell
For VR20R726*** models, combo brush and soft action brush are provided.
1_VR7200_Q_guide_EN_00827G-03_SB.indd 2 2020-01-13 오후 7:53:56
English-3
Safety information
2-1
Before operating the appliance, please
read this manual thoroughly and retain it
for your reference.
Because these following operating
instructions cover various models, the
characteristics of your vacuum cleaner
may differ slightly from those described
in this manual.
Caution/Warning symbols used
WARNING
Indicates that a danger of death or serious
injury exists.
CAUTION
Indicates that a risk of personal injury or
material damage exists.
Other symbols used
NOTE
Indicates that the following text contains
additional important information.
For information on Samsung’s
environmental commitments
and product specic regulatory
obligations e.g. REACH (WEEE,
Batteries) visit: samsung.com/uk/
aboutsamsung/samsungelectronics/
corporatecitizenship/data_corner.html
Important safety instructions
When using an electrical appliance, basic
precautions should be observed, including
the following:
Read all instrucrions before using your
robot vacuum cleaner.
Unplug the charger / docking station
from outlet when not in use and before
conducting maintenance.
WARNING
To reduce the risk of re, electric shock,
or injury:
General
Use only as described in this manual.
Do not operate POWERbot or the
charger/docking station if it has been
damaged in any way.
If the vacuum cleaner is not working as
it should, has been dropped, damaged,
left outdoors, or dropped in water, return
it to a customer care center.
Do not handle the charger / docking
station or POWERbot with wet hands.
Use only on dry, indoor surfaces.
This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved. Children shall not play with
the appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
If the supply cord is damaged, it must
be replaced by the manufacturer or its
service agent or a similarly qualied
person in order to avoid a hazard.
1_VR7200_Q_guide_EN_00827G-03_SB.indd 3 2020-01-13 오후 7:53:57
English-4
Safety information
2-2
Charger / Docking station
Do not modify the polarized plug to t a
non-polarized outlet or extension cord.
Do not use outdoors or on wet surfaces.
Unplug the charger / docking station
from the outlet when not in use and
before servicing.
Use only the charger / docking station
supplied by the manufacturer to
recharge.
Do not use with a damaged cord or plug
or a loose power outlet.
Do not pull or carry by the cord, use the
cord as a handle, close the door on the
cord, or pull the cord around sharp edges
or corners. Keep the cord away from
heated surfaces.
Do not use extension cords or outlets
with inadequate current carrying
capacity.
Do not unplug by pulling on the cord. To
unplug, grasp the plug, not the cord.
Do not mutilate or incinerate batteries as
they will explode at high temperatures.
Do not attempt to open the charger /
docking station. Repairs should only be
carried out by a qualied customer care
center.
Do not expose the charger / docking
station to high temperatures or allow
moisture or humidity of any kind to
come into contact with the charger /
docking station.
Do not charge the non-rechargeable
batteries with the charger / docking
station.
COMMISSION REGULATION (EU)
2019/1782
Ecodesign requirements for external
power supplies : www.samsung.com/
global/ecodesign_component
POWERbot
Do not pick up hard or sharp objects
such as glass, nails, screws, coins, and
etc.
Do not use without a lter in place.
When servicing the unit, never put
ngers or other objects into the fan
chamber in case the unit accidentally
turns on.
Do not put any objects into openings.
Do not use with any openings blocked;
keep openings free of dust, lint, hair, and
anything that may reduce air ow.
Do not pick up toxic materials (chlorine
bleach, ammonia, drain cleaner, etc.).
Do not pick up anything that is burning
or smoking, such as cigarettes, matches,
or hot ashes.
Do not use to pick up ammable or
combustible liquids such as gasoline or
use in areas where they may be present.
Also do not use in:
Locations with candles or desk lamps
on the oor.
Locations with unattended res (re or
embers).
Locations with distilled alcohol,
thinner, ashtrays with burning
cigarettes, etc.
Do not use POWERbot in an enclosed
space lled with vapours given off by oil
based paint, paint thinner, moth proong
substances, ammable dust, or other
explosive or toxic vapours.
Leaks from battery cells can occur
under extreme usage or temperature
conditions. If the liquid gets on
skin, wash quickly with water. If the
liquid gets into the eyes, ush them
immediately with clean water for a
minimum of 10 minutes. Seek medical
attention.
1_VR7200_Q_guide_EN_00827G-03_SB.indd 4 2020-01-13 오후 7:53:58
English-5
Safety information
2-3
WARNING
Power related
Please prevent any risk of electric shock
or re.
Do not damage the power cord.
Do not pull the power cord too hard or
touch the power plug with wet hands.
Do not use a power source other than
100-240V~ and also do not use a
multi outlet to supply power to number
of devices at the same time. (Do not
leave the cord carelessly on the oor.)
Do not use a damaged power plug,
power cord or loose power outlet.
Clean dust or any foreign matters on the
pin and contact part of the power plug.
There is a risk of electric shock or
malfunction.
Before use
Do not use POWERbot near a heater or
combustible materials.
Do not use powerbot near re or
ame such as a movable heater, a
candlelight, a desk lamp, a replace
etc. or in a place where combustible
materials such as gasoline, alcohol,
thinner etc. exist.
Make sure there are no dangerous
objects around the POWERbot’s cleaning
area to prevent collision and unplug any
electric heaters or fans.
The POWERbot is intended for household
use therefore do not use it in an attic,
basement, storage, industrial building,
out of indoor space, places with moisture
(such as bathroom, laundry), on the table
or shelves.
The POWERbot can be damaged or
malfunction.
Be sure POWERbot does not pass
through or touch any kind of liquids.
The POWERbot can be severely
damaged and it may contaminate other
areas if the wheels pass through liquid.
Attach the boundary markers to places
where the POWERbot may fall such as
the top of a staircase or a bannister to
prevent product damage and injury.
Please keep the cliff sensor clean at all
times for safety.
Do not spill any liquids on the docking
station.
There is a risk of re or electric shock.
Do not use the charger / docking station
for anything other than its intended
purpose.
There is a risk of re or severe damage
to the docking station.
Always keep the cliff sensor clean for
your safety.
In use
If any abnormal sounds, smells or smoke
come from POWERbot, immediately shut
off the emergency switch at the bottom
of POWERbot and contact a service
center.
Cleaning and maintenance
When power cord is damaged, contact
a service center to get it replaced by
certied repairman.
There is a risk of re or electric shock.
Please check with a Samsung Electronics
service center when exchanging
batteries.
Using batteries from other products
can cause malfunction.
CAUTION
Before use
Insert the dustbin before using POWERbot.
Be careful with the followings for proper
automatic recharging.
Always turn on the power of the
docking station.
Install the docking station where the
POWERbot can nd it easily.
Do not leave any object in front of the
docking station.
1_VR7200_Q_guide_EN_00827G-03_SB.indd 5 2020-01-13 오후 7:53:59
English-6
Safety information
2-4
When installing the docking station, do
not leave the cord carelessly on the oor
since POWERbot may get tangled by it.
Do not use POWERbot on black colored
oors.
The POWERbot may not be able to
operate normally.
Do not pick up POWERbot by the dustbin
holder.
Do not place any objects within 0.5 m
to both sides and 1 m to the front of the
docking station.
Make sure the docking station’s charging
contact is not damaged or have any
foreign matters on it.
Do not install the docking station in an
area with a dark oor.
If the oor around the docking station
is dark, recharging is hindered.
Move any obstacles that may disturb
POWERbot’s movement (such as children’s
indoor swing or slides) before cleaning.
Do not use the POWERbot in a place
which is narrower than the turning
radius (0.5 m or less) of the POWERbot.
To clean all areas of your house, open all
rooms and attach the boundary markers
on the places where the POWERbot
may get damaged such as a front door,
veranda, bathroom, and stairs for safety.
For the very low areas where the
POWERbot may get stuck, attach the
boundary markers to prevent the
POWERbot from getting in.
If a brush or brush cover is not assembled
correctly, scratches may occur on the
oor, or product malfunction may occur.
Before operating the POWERbot, remove
the objects which could break such as
a frame, mirror, and porcelain items
so that the POWERbot works without
interruption.
In use
Using POWERbot on thick carpet may
damage both POWERbot and the carpet.
The POWERbot cannot pass over carpet
that is thicker than 1 cm.
Do not use POWERbot on tables or other
high surfaces.
There is a risk of damage if it falls.
The POWERbot may bump into chair,
desk legs therefore move them away for
faster and efcient cleaning.
When POWERbot is operating, do not lift
it up or carry it to another area.
Do not hold by driving wheels of
POWERbot when carrying it to another
area.
Do not put any objects on top
of POWERbot since it may cause
malfunction.
Remove any large papers or plastic bags
immediately when using POWERbot
since they may block the intake.
Do not aim the red pointer directly at
people or animals.
Do not lie down around the POWERBOT
that is running.
Your hair may be caught in the brush,
resulting in physical injury.
Cleaning and maintenance
Prevent any damage to POWERbot by
complying the followings.
Do not clean POWERbot by spraying
water directly onto it or use benzene,
thinner, acetone or alcohol to clean it.
Do not disassemble or repair POWERbot.
This should only be done by a certied
repairman.
Always keep the obstacle sensor and cliff
sensor clean.
If foreign matter accumulates, sensors
may malfunction.
1_VR7200_Q_guide_EN_00827G-03_SB.indd 6 2020-01-13 오후 7:54:01
English-7
3
Charging
Charge the POWERbot fully before using for the first time.
Please install the docking station in a place
where the oor is level and wall is straight.
How to turn on the
emergency switch
Hold the robot vacuum cleaner and
turn on the emergency switch without
pressing any buttons.
Check the charging status.
"
" will turn on according to
charging progress and "FULL" will
turn on when charging is complete.
When the product is purchased, the battery is not charged, so charging must initially be done manually.
0.5 m
1 m
0.5 m
Make sure the
charge pins on the
robot vacuum cleaner
and the charger are
aligned.
Ensure the power
cord is arranged
neatly next to the
wall.
Ú Install with the grain of wood oors.
Install the charger
where the robot vacuum
cleaner can easily nd
it.
1_VR7200_Q_guide_EN_00827G-03_SB.indd 7 2020-01-13 오후 7:54:05
English-8
4-1
Using the robot vacuum cleaner
Starting Auto clean mode
The POWERbot moves and
automatically cleans the set
areas only once.
Stop cleaning:
Press and release the button
Starting Spot clean mode
Press and release this button.
The POWERbot cleans a
localized area intensely.
Recharging
You can command POWERbot
to recharge at the docking
station automatically while it is
cleaning by pressing this button.
Auto Clean Spot Clean Repeat clean
Manual Clean
Manual clean mode
can be selected by the
direction control buttons
of the remote controller.
Press the [
] on the
remote controller rst
and then press the [Start/
Stop ].
POWERbot increases suction power in Spot clean and Point cleaning mode.
1_VR7200_Q_guide_EN_00827G-03_SB.indd 8 2020-01-13 오후 7:54:07
English-9
Using the robot vacuum cleaner
4-2
About the boundary markers
To prevent the POWERbot from entering the following areas, attach
the boundary markers on the oor in the shape at an interval of
about 15cm.
About 15cm
Boundary
markers
About 5cm
About 15cm
Boundary
markers
where a raised spot is below 5cm where there is a slide, swing, replace or any
ammable substance or moisture.
Above 1.5cm
boundary
markers
Boundary
markers
where a threshold is above 1.5cm where there is risk of falling such as stairs, porches
or guardrails.
1_VR7200_Q_guide_EN_00827G-03_SB.indd 9 2020-01-13 오후 7:54:09
English-10
1. Power
Turn POWERbot's power on/off
2. Recharging
Select to recharge POWERbot at the docking station
automatically
3. Start/Stop
Select to start or stop cleaning process
4. Auto clean
Select to clean all set areas only once and then
automatically return to the docking station
5. Spot clean
Select to clean a localized area intensely
6. Repeat clean
Select to clean repeatedly until the battery becomes
very low with indicator blinking
7. Turbo mode
Select to clean with the strongest suction power
8. Normal mode
Select to clean with moderate suction power
9. Quiet mode
Select to clean with lower operation noise
10. Sound
Select to set the voice guide
Voice Guide (English) Sound Effects Mute
Press and hold the sound button to change and set
a language.
11. Schedule / Cancel(3sec)
Refer to page 11
12. Clock
Refer to page 11
13. Remote control
Select to turn Wi-Fi function on or off
Using the robot vacuum cleaner
4-3
2
6
8
12
10
7
13
5
9
11
3 4
1
1_VR7200_Q_guide_EN_00827G-03_SB.indd 10 2020-01-13 오후 7:54:10
English-11
Setting time/schedule
Only Auto clean mode can be scheduled.
5
Setting the time
You must set the current time before using the One-time/daily schedule.
Setting the schedule
Setting/cancelling the schedule can only be done while POWERbot is docked on the docking station.
Setting complete
Start setting Select "Hour" Select "Minute"
Select "AM/PM"
Skip to previous,
next setting
Start setting
Setting complete Select "AM/PM" Select "Minute"
Select "One-time" or
"Daily" schedule
Select "Hour"
Skip to previous, next setting
Cancelling during setup
Setting will be canceled automatically when there's no input for
7seconds
Cancelling One-time/Daily schedule
When both One-time/
Daily schedule are set
or
or
Press for 3 sec. Select the schedule Cancel complete
When either One-time
or Daily schedule is set
Press for 3 sec.
1_VR7200_Q_guide_EN_00827G-03_SB.indd 11 2020-01-13 오후 7:54:13
English-12
Cleaning and maintaining
You must turn off the emergency switch before cleaning POWERbot.
6-1
Dustbin
1
Press the button to
remove the dustbin
2
Remove the dustbin
cover
3
Remove dust in the
dustbin and cyclone
unit
'Click'
4
Detach the cyclone
unit from the dustbin
cover, and then wash
the dustbin and the
lter
5
Reassemble the
dustbin
6
Reinsert the dustbin
into the main body
until it clicks
1_VR7200_Q_guide_EN_00827G-03_SB.indd 12 2020-01-13 오후 7:54:15
English-13
Cleaning and maintaining
You must turn off the emergency switch before cleaning POWERbot.
6-2
Brush and Auto shutter tool
Soft Action Brush
Combo Brush
1
Remove the
brush cover
2
Remove the
brush
3
Clean the brush
Remove remaining dirt
on the soft action brush
with a wet tissue or a
dry cloth.
4
Clean the auto
shutter tool
5
Reassemble the brush
6
Reassemble the brush cover
For VR20R726*** models, check that the brush cover
is correct for the assembled brush.
If a brush or brush cover is not assembled correctly after the maintenance work, scratches may occur on the
oor, or product malfunction may occur. Therefore, assemble them correctly by referring to the cleaning and
maintaining section of a user manual.
Information codes
Refer to the user manual for steps to take for each Information code with mark on the display panel.
Brush design may differ depending on the model. Do not clean the brush with water.
1_VR7200_Q_guide_EN_00827G-03_SB.indd 13 2020-01-13 오후 7:54:19
English-14
Downloading the SmartThings App
f Download and install the SmartThings app from the markets (Google Play Store, Apple App Store, or
Samsung Galaxy Apps). To nd the app, use the keyword “SmartThings”.
NOTE
f SmartThings is incompatible with tablets and some mobile devices.
Android 6.0 or later (at least 2GB of RAM) is recommended.
f iPad and some mobile devices may not be supported.
iOS 10.0 or later / iPhone 6 or later is supported.
f Visit Play Store or App Store to see if your mobile device is compatible with SmartThings.
f The supported features are subject to change without any prior notice.
Setting up a Samsung account
f You must sign in to a Samsung account before using the SmartThings app.
f To set up a Samsung account, you can follow the directions provided by the SmartThings app.
f Or, if you have a Samsung smartphone, you can add your Samsung account in the setting app of your
smartphone. Then, it will automatically sign in to your Samsung account.
NOTE
f If you cannot complete the product registration, please take the following steps.
Try the registration procedure again as you have directed by the pop-up messages.
Conrm that the UPnP option of your wireless router is active, and then try the registration procedure again.
Conrm that your wireless router is operating in wireless mode, and then try the registration procedure
again.
If you have two or more POWERbots, turn off the other POWERbots, and then try to register your POWERbot
again.
If there is any other wireless router that has the same SSID as your wireless router, the registration might be
failed.
f
Remote control and Wi-Fi indicator
On
Remote control is blocked. (The remote controller can still be
allowed.)
Off Remote control is allowed.
On The POWERbot is connected to the wireless router.
Off The POWERbot is trying to connect the wireless router.
Hereby, Samsung Electronics, declares that the radio equipment type appliance is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
The ofcial Declaration of conformity may be found at http://www.samsung.com, go to Support > Search
Product Support and enter the model name.
Wi-Fi
Frequency range 2412 - 2472 MHz
Transmitter power(Max) 20 dBm
SmartThings App
The SmartThings App is only compatible with models that have a Wi-Fi
function.
7
1_VR7200_Q_guide_EN_00827G-03_SB.indd 14 2020-01-13 오후 7:54:21
English-15
Note
1_VR7200_Q_guide_EN_00827G-03_SB.indd 15 2020-01-13 오후 7:54:21
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care center.
Country Contact Center Web Site
LITHUANIA 8-800-77777 www.samsung.com/lt/support
LATVIA 8000-7267 www.samsung.com/lv/support
ESTONIA 800-7267 www.samsung.com/ee/support
1_VR7200_Q_guide_EN_00827G-03_SB.indd 16 2020-01-13 오후 7:54:22
POWERbot
Kiirjuhend
VR20R72**** seeria
Lugege suunised enne seadme kasutamist hoolikalt läbi.
Kasutamiseks ainult siseruumides.
2_VR7200_Q_guide_ET_00827G-03_SB.indd 1 2020-01-14 오후 2:25:14
Eesti-2
Osade loend
1
Põhiseade
Põhiosad
Kaugjuhtimisseade
Dokkimisjaam
Akud
(AAA-tüüpi)
Kiirjuhend Varulter
Toitejuhe
Akulaadija Piirdemarkerid Kerge koristamise
hari / harja kate
Combo-hari / harja
kate
Lisatarvikud võivad olenevalt mudelist erineda.
Vt lk 15, kuidas paigaldada piirdemarkereid.
Aku andmed: Liitiumioon, 21,6 V, 3600 mAh, 12 elementi
VR20R726*** mudelitel on kaasas combo-hari ja kerge koristamise hari.
2_VR7200_Q_guide_ET_00827G-03_SB.indd 2 2020-01-14 오후 2:25:16
Eesti-3
Ohutusalane teave
2-1
Enne seadme kasutamist lugege käesolev
kasutusjuhend hoolikalt läbi ja hoidke see
hilisemaks ülevaatuseks alles.
Kuna järgnevad kasutussuunised hõlmavad
erinevaid mudeleid, võivad teie tolmuimeja
näitajad erineda veidi käesolevas juhendis
esitatutest.
KASUTATAVAD ETTEVAATUSABINÕUDE/
HOIATUSTE SÜMBOLID
HOIATUS
Tähistab surma- või tõsiste vigastuste ohtu.
ETTEVAATUST
Tähistab kehavigastuste või materiaalse kahju
ohtu.
TEISED KASUTATAVAD SÜMBOLID
MÄRKUS
Näitab, et järgnev tekst sisaldab olulist
lisateavet.
Teabe saamiseks Samsungi
keskkonnakohustuste ja tootekohaste
regulatiivkohustuste, nt REACH-i (WEEE,
akud), kohta külastage veebilehte samsung.
com/uk/aboutsamsung/samsungelectronics/
corporatecitizenship/data_corner.html
Olulised ohutusalased suunised
Elektriseadme kasutamisel tuleb rakendada
üldiseid ettevaatusabinõusid, sh järgmisi.
LUGEGE KÕIK SUUNISED ENNE POWERboti
KASUTAMIST LÄBI.
Seadme mittekasutamisel ja enne hoolduse
teostamist eemaldage see pistikupesast.
HOIATUS
Tulekahju-, elektri- või vigastusohu
vähendamiseks järgige alltoodud
suuniseid.
ÜLDINE
Kasutage seadet ainult selles
kasutusjuhendis kirjeldatud viisil.
Ärge kasutage POWERboti ega akulaadijat/
dokkimisjaama, kui see on mis tahes viisil
kahjustunud.
Kui tolmuimeja ei tööta nii, nagu peaks,
on maha kukkunud, õue jäetud, seda on
kahjustatud või vette pillatud, viige seade
klienditeeninduskeskusse.
Ärge käsitsege akulaadijat/dokkimisjaama
ega POWERboti märgade kätega.
Kasutage ainult siseruumis kuivadel
pindadel.
Seadet võivad kasutada lapsed alates
8.eluaastast ning piiratud füüsiliste,
sensoorsete või vaimsete võimete või
vähese kogemuse või väheste teadmistega
inimesed, kui tagatud on järelevalve
või neid on juhendatud seoses seadme
ohutu kasutamisega ning nad mõistavad
kaasnevaid ohte. Lapsed ei tohi seadmega
mängida. Lapsed ei tohi teha puhastus- ega
hooldustoiminguid ilma järelevalveta.
Kui toitejuhe on kahjustunud, peab
tootja, tema hooldustöötaja või sarnase
kvalikatsiooniga isik selle ohu vältimiseks
asendama.
2_VR7200_Q_guide_ET_00827G-03_SB.indd 3 2020-01-14 오후 2:25:17
Eesti-4
Ohutusalane teave
2-2
Akulaadija/dokkimisjaam
Ärge muutke polariseeritud pistikut selle
sobitamiseks polariseerimata pistikupesa
või pikendusjuhtmega.
Ärge kasutage õues ega märjal pinnal.
Kui te akulaadijat/dokkimisjaama ei kasuta
või soovite seda hooldada, eemaldage see
pistikupesast.
Kasutage laadimiseks ainult tootja tarnitud
akulaadijat/dokkimisjaama.
Ärge kasutage, kui toitejuhe või pistik
on kahjustatud või pistikupesa lõdvalt
kinnitatud.
Ärge tõmmake ega vedage seadet juhtmest,
kasutage juhet käepidemena, jätke juhet
ukse vahele ega tõmmake juhet ümber
teravate servade või nurkade. Hoidke juhe
eemal kuumadest pindadest.
Ärge kasutage pikendusjuhet ega
pistikupesasid, mille võimsus pole piisav.
Ärge eemaldage seadet vooluvõrgust
juhtmest tõmmates. Vooluvõrgust
eemaldamiseks võtke kinni pistikust, mitte
juhtmest.
Ärge vigastage ega kuumutage akusid,
kuna need võivad kõrgetel temperatuuridel
plahvatada.
Ärge proovige akulaadijat/dokkimisjaama
avada. Parandusi võivad teha ainult
volitatud hooldusmehaanikud.
Ärge jätke akulaadijat/dokkimisjaama kõrge
temperatuuriga kohta ega laske mis tahes
laadi niiskusel akulaadija/dokkimisjaamaga
kokku puutuda.
Ärge laadige akulaadijaga
mittetaaslaetavaid akusid.
KOMISJONI MÄÄRUS (EL) 2019/1782
Välistoiteallikate ökodisaini nõuded :
www.samsung.com/global/ecodesign_
component
POWERbot
Ärge imege seadmesse kõvasid või teravaid
esemeid, nt klaasi, naelu, kruvisid, münte
jms.
Ärge kasutage seadet ilma ltrita. Ärge
pange seadme hooldamisel kunagi sõrmi
ega muid esemeid ventilaatorikambrisse,
sest seade võib kogemata sisse lülituda.
Ärge pange avadesse esemeid. Ärge
kasutage seadet suletud avadega.
Hoidke avad vabana tolmust, kiududest,
juuksekarvadest ja muust, mis võib
õhuvoolu takistada.
Ärge imege seadmega mürgiseid
aineid (kloorpleegiteid, ammoniaaki,
torupuhastusvahendeid jms).
Ärge imege seadmega põlevaid või
suitsevaid esemeid, nt sigarette, tikke või
kuuma tuhka.
Ärge kasutage seadet kergestisüttivate ega
põlevate vedelike (nt bensiin) koristamiseks
ega nende ainete läheduses.
Lisaks ärge kasutage toodet:
Kohad, kus põrandal on küünlaid või
laualampe.
Kohad, kus on järelevalveta tulease (tuli
või söed).
Kohad, kus on destilleeritud alkoholi,
lahusteid, põlevate sigarettidega
tuhatoose jne.
Ärge kasutage POWERboti suletud ruumis,
mis on täidetud õlivärvi, värvilahusti või
koitõrjevahendi aurude, kergestisüttivate
pulbrite või muude plahvatusohtlike või
toksiliste aurudega.
Äärmuslikes tingimustes või ekstreemsel
temperatuuril kasutamisel võib aku hakata
lekkima. Kui akuvedelik satub nahale, peske
seda kiiresti veega. Kui vedelik satub silma,
loputage silmi kohe puhta veega vähemalt
10 minuti jooksul. Pöörduge arsti poole
2_VR7200_Q_guide_ET_00827G-03_SB.indd 4 2020-01-14 오후 2:25:17
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Samsung VR20R7250WC Kasutusjuhend

Tüüp
Kasutusjuhend

teistes keeltes