Wilfa RVC-D4000LIN Kasutusjuhend

INNOBOT

ROBOT VACCUUM RVC-D4000LIN

EN ·Instruction manual DE ·Anleitung

NO ·Bruksanvisning NL ·Instructies

SE ·Bruksanvisning PL ·Instrukcje

DK ·Betjeningsvejledning FR ·Instructions

FI ·Käyttöohje

2

NO

SE

DK

FI

EN

NL

PL

FR

LES ALLE ANVISNINGER FØR BRUK

LÆS ALLE VEJLEDNINGER INDEN BRUG

LUE OHJEET HUOLELLISESTI ENNEN KÄYTTÖÄ

LEES VÓÓR GEBRUIK ALLE INSTRUCTIES

PRZED UŻYCIEM ZAPOZNAĆ SIĘ ZE WSZYSTKIMI ZALECENIAMI

PRENEZ CONNAISSANCE DE TOUTES LES INSTRUCTIONS AVANT UTILISATION

DE

LESEN SIE DIE ANLEITUNG VOR DEM GEBRAUCH GRÜNDLICH DURCH

LÄS IGENOM ALLA INSTRUKTIONER INNAN PRODUKTEN ANVÄNDS

READ ALL INSTRUCTIONS BEFORE USE

4

INSTRUCTION MANUAL · ROBOT VACUUM

EN

5

EN

INNOBOT · RVC-D4000LIN

CONTENTS

6 IMPORTANT SAFETY INSTRUCTIONS

8 BATTERY AND CHARGING

9 INSTRUCTIONS ON ENVIRONMENTAL PROTECTION

10 SYSTEM DISCLAIMER

11 PRODUCT OVERVIEW – GENERAL

12 PRODUCT OVERVIEW – VACUUM CLEANER

13 PRODUCT OVERVIEW – DETAILED

13 PRODUCT OVERVIEW – LIGHTS AND BUTTONS

15 INSTALLATION

17 APP USE

18 MAINTENANCE AND CLEANING

20 TROUBLESHOOTING

22 FAULT MESSAGES

25 GUARANTEE

26 PRODUCT SPECIFICATIONS

26 SUPPORT AND SPARE PARTS

26 RECYCLABILITY

6

INSTRUCTION MANUAL · ROBOT VACUUM

EN

IMPORTANT SAFETY INSTRUCTIONS

• This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack

of experience and knowledge if they have been

given supervision or instruction concerning use of

the appliance in a safe way and understand the

hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall

not be made by children without supervision.

• This product is only used for ﬂoor cleaning in home

environment, and should not be used in outdoor,

non-ﬂoor, commercial or industrial environment.

• Do not let children play with the machine. Please

supervise children and pets to keep them as far

away as possible when the machine works.

• If the power cord is damaged, it must be replaced

with a special cord or a special component

purchased from its manufacturer or maintenance

department.

• Do not let children, pets sit on the machine at any

time.

• Do not handle this robot by using the protective

cover of laser radar as handle.

• This appliance shall not be used by children

7

INNOBOT · RVC-D4000LIN

EN

• Do not use it in suspended environments without

protective fences (such as duplex ﬂoors, open

balconies and furniture tops).

• Do not use it in an environment where the

temperature is higher than 35°C lower than 0°C

or there are any liquids and sticky objects on the

ground.

• Do not use it to clean any burning objects.

• Before use, please arrange and fold the wires on

the ﬂoor in case of any obstruction that blocks the

machine movement.

• Please put away fragile objects and sundries (such

as vases and plastic bags, etc.) on the ground, to

avoid damage to valuables at home when the

machine is blocked during operation or slightly

collided.

• Do not use the mopping mode on the carpet.

When mopping the ﬂoor, please set up virtual

walls or forbidden zones in the carpet area.

• Do not let the machine absorb hard objects or

sharp objects (such as decoration waste, glass

and nails, etc.).

• Please clean and maintain the appliance and base

in power-off state.

8

INSTRUCTION MANUAL · ROBOT VACUUM

EN

• Do not turn the machine upside down on the

ground for a long time.

• If products need to be transported, please make

sure that the machine is turned off, and it is

recommended to use the original packaging box

for packaging protection.

BATTERY AND CHARGING

• Do not use any third-party battery, power cord or

base.

• Do not disassemble, repair or modify the battery

or base without permission.

• Do not place the auto-clean base near the heat

source (such as radiator, etc.).

• Before scrapping the machine, the power supply

must be disconnected, and the battery should be

taken out of the machine.

• If it is not used for a long time, please turn off the

machine after being fully charged and put it in a

cool and dry place.

• It is recommended to charge at least once a

month.

INSTRUCTIONS ON ENVIRONMENTAL PROTECTION

The following information is only applicable when

9

INNOBOT · RVC-D4000LIN

EN

discarding this robot, and is not a daily operation

instruction:

Chemical substances contained in the built-in

lithium-ion battery of this product will pollute the

environment. Please remove the battery before you

discard the machine, and hand it over to a professional

battery recycling station for centralized disposal.

Steps to disassemble the battery:

1. Let the robot run until it is low in power and cannot

be cleaned without touching the auto-clean base.

2. Turn the robot off.

3. Disassemble the bottom shell of the robot.

4. Press the buckle and pull out the connector plug

of the battery, then take out the battery.

5. Remove the battery cover plate and take the

battery out.

NOTE:

• When disassembling the battery, make sure that

the battery is exhausted and operated away from

the base.

• Please disassemble the whole battery pack

together, and do not damage the battery pack

casing, in case of short circuit or leakage of

10

INSTRUCTION MANUAL · ROBOT VACUUM

EN

dangerous substances.

• If you touch battery ﬂuid, please rinse with plenty

of water and get medical assistance immediately.

SYSTEM DISCLAIMER

The list of smartphone types in the market is long and

increasing. System performance can vary for different

combinations of the operating system and how it is

implemented in the phone model. Alterations from

industry can have an impact too. Therefore, although

we expect good performance in most cases, the

expected performance of the app is not guaranteed.

Although the app most likely will work for a long time

with older hardware and software versions you need

to keep your phone’s operations systems updated to

be sure to get the app fully functional.

Minimum requirement of January 2023:

• iOS 14.00

• Android 10.0

11

INNOBOT · RVC-D4000LIN

EN

PRODUCT OVERVIEW – GENERAL

1. Robot vacuum cleaner

Accessories:

2. Removable wet mop-plate

3. Dust box

4. Side brush

5. Filter screen

6. Cleaning tool

7. Main brush

8. Water tank

9. Wet mop

10. Charging station

11. Power cord

1

2 3 4

567

8

11

10

9

12

INSTRUCTION MANUAL · ROBOT VACUUM

EN

1. Sensor

2. ON/Off button

3. Home button

4. Cover

5. Side brush

6. Main brush

7. Charging electrodes

8. Main brush cover

9. Wet mop holder

PRODUCT OVERVIEW – VACUUM CLEANER

1

23

4

5

6

7

8

9

13

INNOBOT · RVC-D4000LIN

EN

2

3

1. Reset

2. Fastener

3. Lock

PRODUCT OVERVIEW – DETAILED

ROBOT DUSTBOX

PRODUCT OVERVIEW – LIGHTS AND BUTTONS

White light is always on Standby / Normal operation /

Wi-Fi is connected

White light breaths Firmware upgrade in progress /

Restoring factory settings /Starting up

White light ﬂashes Connecting to the network

Yellow light breaths Charging

Yellow light ﬂashes Recharging / Power is lower than 15%, robot is

disconnected from the charger.

Red light ﬂashes Abnormal state

On/Off button Long press for 3s, power on or power off.

Short press, start or pause.

Recharging button In operation state, short press, robot pauses

cleaning. In pause state, short press start

recharging. In charging state, short press to

stop recharging.

1

14

INSTRUCTION MANUAL · ROBOT VACUUM

EN

INSTALLATION

To install the charging station, place it against the wall, and connect the power

cord. Make sure there is enough space in front and on the sides of the charger.

Note:

• Do not place the charging station in direct sunlight.

• The charger requires more than 1.5-meter space in front and more than

0.5-meter space on both sides.

• Make sure the power cord is not placed where the robot can drag it.

POWER ON AND CHARGE

Put the robot on the base and align the charging electrodes with charging

contact. For daily use, you can start intelligent recharge by short pressing the

button

• Robot can’t start up when it has low power. Please put it on the charger to

recharge.

• Robot will start up automatically after connecting to the charger and can’t be

shut down while recharging.

SWEEPING MODE

Insert the mop along the slot of the mop holder and stick it on the hook and

loop fastener. Note: Clean the dust box regularly in case of the dirt affecting the

cleaning effect.

MOPPING MODE

1. Insert the mop along the slot of the mop holder and stick it on the hook and

loop fastener.

15

INNOBOT · RVC-D4000LIN

EN

2. Open the water tank lid, ll the water tank and then fasten the water tank lid.

Note:

• Do not use detergents, disinfectants, solid cleaners or other cleaning

products, or inject hot water into the water tank in case of corrosion and

damage to the water tank.

• The water tank should be dry before performing a mopping task.

3. Push the water tank into the bottom of the robot, and it will make a “click”

sound when it is installed in place.

Note:

• When mopping the ﬂoor, please set up virtual walls or no-mop zones in the

carpet area.

• Before starting sweeping/mopping function, be sure to remove any water

accumulated on the ﬂoor.

APP USE

CLEANING MODE/LEVEL SELECTION

You can choose various cleaning modes and water ﬂow rates.

Mop holder

Hook and loop

fastener Mop

16

INSTRUCTION MANUAL · ROBOT VACUUM

EN

DO NOT DISTURB MODE (DND)

When Do Not Disturb mode is activated, proceeding at breakout point,

scheduled cleaning and active voice reporting are unavailable in robot.

Do Not Disturb mode is activated by default during the period from 22:00 to

9:00. Do Not Disturb mode can be deactivated in App.

CLEANING MODE WITHOUT MAP

When no map is stored, the robot will start cleaning each zone by a square area

of 6m×6m. When a map is stored, the robot will start cleaning each room along

the route planned automatically and return to base after completion.

MEMORY MAP

When memory map is activated in the App, the robot will save and update the

map after nishing cleaning task and recharging successfully. After a map is

completed successfully, you can split or merge zones or name any room in the

App.

EDGE CLEANING MODE

When choosing edge cleaning mode in the App, the robot will automatically

recognize range of the area to clean, and start cleaning along the edges, and

return to base automatically after nishing cleaning.

SPECIFIED AREA CLEANING MODE

When an area to be cleaned is specied in the App, the robot will clean the

specied area. Note: During cleaning, the robot may go beyond a dened area,

remove any obstacle on the ﬂoor within dened area since denition of any area

will not ensure safe separation.

FIXED-POINT CLEANING MODE

When choosing xed-point cleaning and have selected a target point in the App,

the robot will route cleaning task and start cleaning within a rectangular area of

2m × 2m based on the target position dened in the map in App.

SCHEDULED CLEANING MODE

User can schedule a cleaning task in App, and robot will start the cleaning task

as scheduled and return to the base upon end of the task. Note: Any scheduled

cleaning task will not be executed during the time when Do Not Disturb mode is

activated.

VIRTUAL WALL/NO-GO ZONE

User can dene virtual wall/ no-go area in App which the robot will avoid

cleaning. Note: Before using this function, you have to store a map in the App.

Moving the robot or change of indoor environment may cause the original map

lost and any virtual wall/ no-go zone unavailable.

17

INNOBOT · RVC-D4000LIN

EN

RESET/RESTORE SYSTEM

• By long pressing the Reset button for 3 seconds, you will not only restore

factory settings, but also reset the rmware to the last version.

• By long pressing Reset button for 10 seconds, the machine will clear all

network connection information, map information, scheduled task and do-

not-disturb information, and customization information, and reset the suction

power to the default level.

Note: After resetting/restoring the system, the robot needs to reconnect the

APP, and the relevant settings in the APP are removed.

MAINTENANCE AND CLEANING

DUST BOX

1. Open the cover, press the dust box lock and take out the dust box

2. Dispose the trash in dust box, and clean the box with cleaning brush

3. Remove the dust box cover, take the lter screen out, dispose trash and clean

the screen.

Note:

• It is recommended to clean the dust box at least once a week. Dry the dust

box and lter screen before use (at least 24 hours)

• Do not wash the dust box with water, it can damage electric components.

18

INSTRUCTION MANUAL · ROBOT VACUUM

EN

WATER TANK

1. As shown in the gure, press the tank fastener down, and draw the tank out

horizontally.

2. Turn the plastic tank cover, discharge any residual water in it and mount the

cover in place.

3. As shown in the gure, mount the tank properly.

SIDE BRUSH

1. Turn the robot over and remove the side brush xing screws.

2. Remove and clean the side brush.

3. Reinstall the side brush and tighten the screws.

Note: It is recommended to replace the side brush every 3-6 months to ensure

the cleaning effect.

19

INNOBOT · RVC-D4000LIN

EN

MAIN BRUSH

1. Turn the robot over, press and hold the two release buttons to remove the

main brush cover.

2. Take out the main brush upwards.

3. Use the knife on the cleaning brush to cut the entangled hair and clean the

main brush.

4. Put back the main brush and the main brush cover, and press the main brush

cover to install it in place.

Note: It is recommended to replace the main brush every 6-12 months to ensure

the cleaning effect.

BRUSH CLEANING METHOD

Use the included cleaning tool.

CLIFF SENSOR

Use a soft dry cloth to clean the cliff sensor every 3 months.

OPTICAL SENSOR

The robot contains precision optical sensor: Front sensor. Be sure to clean these

sensors with soft and dust-free cloth to remove any dirt or dust on them, which,

if accumulating heavily, may impair the obstacle avoidance performance of

the robot. Note: Do not use chemicals such as detergent or spray to clean the

sensor.

Cliff sensor

20

INSTRUCTION MANUAL · ROBOT VACUUM

EN

TROUBLESHOOTING

Problem Solution

Unable to power on 1. The battery is low

2. The ambient temperature is too low (below

0°C) or too high (above 35°C)

Robot fails to start sweeping Low battery level. Charge it to full battery level

Robot cannot return for

charging

1. Too many barriers around charger. Place it

in an unblocked area.

2. Robot is too far from charger. Place robot

near the charger and try again.

Abnormal robot actions Please shut down and restart the robot

Abnormal sound during

cleaning

Please check and clean the foreign matters

on the main brush, side brush, left/right wheel

after the machine is turned off.

Cleaning performance

deteriorates or dust drops

1. Dust box is full. Please empty the dust box.

2. Filter screen is blocked. Please clean the

screen.

3. Main brush is blocked by any foreign

object. Please clean the main brush.

Robot is ofﬂine 1. Weak wi- signals. Make sure robot is in

proper coverage of Wi-Fi signals.

2. Wi-Fi connection fails. Reset Wi-Fi

connection and download the latest app

and try again.

Robot fails to proceed at

breakout point

1. Make sure do not disturb mode is not

activated, which will disable proceeding at

breakout point.

2. Proceeding at breakout point is unavailable

when manually start recharging by

performing operations in the app or

short pressing recharging button or the

appliance is moved to the charger.

Unable to charge Make sure there is sufcient spaces around the

charger, and there is no dust or blockage on

the surface of electrode of the charger.

Leht laadib ...

Wilfa RVC-D4000LIN Kasutusjuhend

Wilfa RVC-D4000LIN Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid