Leht laaditakse ...
INNOBOT
ROBOT VACCUUM RVC-D4000SL, RVC-D4000SL+, RVC-4000AI
EN ·Instruction manual DE ·Anleitung
NO ·Bruksanvisning NL ·Instructies
SE ·Bruksanvisning PL ·Instrukcje
DK ·Betjeningsvejledning FR ·Instructions
FI ·Käyttöohje
2
NO
SE
DK
FI
EN
NL
PL
FR
LES ALLE ANVISNINGER FØR BRUK
LÆS ALLE VEJLEDNINGER INDEN BRUG
LUE OHJEET HUOLELLISESTI ENNEN KÄYTTÖÄ
LEES VÓÓR GEBRUIK ALLE INSTRUCTIES
PRZED UŻYCIEM ZAPOZNAĆ SIĘ ZE WSZYSTKIMI ZALECENIAMI
PRENEZ CONNAISSANCE DE TOUTES LES INSTRUCTIONS AVANT UTILISATION
DE
LESEN SIE DIE ANLEITUNG VOR DEM GEBRAUCH GRÜNDLICH DURCH
LÄS IGENOM ALLA INSTRUKTIONER INNAN PRODUKTEN ANVÄNDS
READ ALL INSTRUCTIONS BEFORE USE
4
INSTRUCTION MANUAL · ROBOT VACUUM
EN
5
EN
INNOBOT · RVC-D4000SL+, RVC-D4000SL, RVC-D4000AI
CONTENTS
6 IMPORTANT SAFETY INSTRUCTIONS
8 BATTERY AND CHARGING
9 INSTRUCTIONS ON ENVIRONMENTAL PROTECTION
10 SYSTEM DISCLAIMER
11 PRODUCT OVERVIEW – GENERAL
12 PRODUCT OVERVIEW – VACUUM CLEANER
13 PRODUCT OVERVIEW – DETAILED
14 PRODUCT OVERVIEW – LIGHTS AND BUTTONS
15 INSTALLATION
17 APP USE
18 MAINTENANCE AND CLEANING
21 TROUBLESHOOTING
23 FAULT MESSAGES
26 GUARANTEE
27 PRODUCT SPECIFICATIONS
27 SUPPORT AND SPARE PARTS
27 RECYCLABILITY
6
INSTRUCTION MANUAL · ROBOT VACUUM
EN
IMPORTANT SAFETY INSTRUCTIONS
• This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge if they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
• This product is only used for floor cleaning in home
environment, and should not be used in outdoor,
non-floor, commercial or industrial environment.
• Do not let children play with the machine. Please
supervise children and pets to keep them as far
away as possible when the machine works.
• If the power cord is damaged, it must be replaced
with a special cord or a special component
purchased from its manufacturer or maintenance
department.
• Do not let children, pets sit on the machine at any
time.
• Do not handle this robot by using the protective
cover of laser radar as handle.
• Do not use it in suspended environments without
7
INNOBOT · RVC-D4000SL+, RVC-D4000SL, RVC-D4000AI
EN
protective fences (such as duplex floors, open
balconies and furniture tops).
• Do not use it in an environment where the
temperature is higher than 35°C lower than 0°C
or there are any liquids and sticky objects on the
ground.
• Do not use it to clean any burning objects.
• Before use, please arrange and fold the wires on
the floor in case of any obstruction that blocks the
machine movement.
• Please put away fragile objects and sundries (such
as vases and plastic bags, etc.) on the ground, to
avoid damage to valuables at home when the
machine is blocked during operation or slightly
collided.
• Do not use the mopping mode on the carpet.
When mopping the floor, please set up virtual
walls or forbidden zones in the carpet area.
• Do not let the machine absorb hard objects or
sharp objects (such as decoration waste, glass
and nails, etc.).
• Please clean and maintain the appliance and base
in power-off state.
8
INSTRUCTION MANUAL · ROBOT VACUUM
EN
• Do not turn the machine upside down on the
ground for a long time.
• If products need to be transported, please make
sure that the machine is turned off, and it is
recommended to use the original packaging box
for packaging protection.
BATTERY AND CHARGING
• Do not use any third-party battery, power cord or
base.
• Do not disassemble, repair or modify the battery
or base without permission.
• Do not place the auto-clean base near the heat
source (such as radiator, etc.).
• Before scrapping the machine, the power supply
must be disconnected, and the battery should be
taken out of the machine.
• If it is not used for a long time, please turn off the
machine after being fully charged and put it in a
cool and dry place.
• It is recommended to charge at least once a
month.
9
INNOBOT · RVC-D4000SL+, RVC-D4000SL, RVC-D4000AI
EN
INSTRUCTIONS ON ENVIRONMENTAL PROTECTION
The following information is only applicable when
discarding this robot, and is not a daily operation
instruction:
Chemical substances contained in the built-in
lithium-ion battery of this product will pollute the
environment. Please remove the battery before you
discard the machine, and hand it over to a professional
battery recycling station for centralized disposal.
Steps to disassemble the battery:
1. Let the robot run until it is low in power and cannot
be cleaned without touching the auto-clean base.
2. Turn the robot off.
3. Disassemble the bottom shell of the robot.
4. Press the buckle and pull out the connector plug
of the battery, then take out the battery.
5. Remove the battery cover plate and take the
battery out.
NOTE:
• When disassembling the battery, make sure that
the battery is exhausted and operated away from
the base.
10
INSTRUCTION MANUAL · ROBOT VACUUM
EN
• Please disassemble the whole battery pack
together, and do not damage the battery pack
casing, in case of short circuit or leakage of
dangerous substances.
• If you touch battery fluid, please rinse with plenty
of water and get medical assistance immediately.
• This appliance contains batteries that are only
replaceable by skilled persons.
• WARNING! For the purposes of recharging the
battery, only use the detachable supply unit
provided with this appliance.
• Only use with RVCD-D17 or D4000 supply unit.
• Detachable supply unit
SYSTEM DISCLAIMER
The list of smartphone types in the market is long and increasing.
System performance can vary for different combinations of the
operating system and how it is implemented in the phone model.
Alterations from industry can have an impact too. Therefore,
although we expect good performance in most cases, the expected
performance of the app is not guaranteed. Although the app most
likely will work for a long time with older hardware and software
versions you need to keep your phone’s operations systems
updated to be sure to get the app fully functional.
Minimum requirement of January 2023:
• iOS 14.00
• Android 10.0
11
INNOBOT · RVC-D4000SL+, RVC-D4000SL, RVC-D4000AI
EN
PRODUCT OVERVIEW – GENERAL
1. Robot vacuum cleaner
Accessories:
2. Vibrating Water tank
3. Dust box
4. Side brush
5. Filter screen
6. Cleaning tool
7. All-round brush
8. Rubber brush
9. Wet-mop
10. Automatic dustbin (included
in RVC-D4000SL+) (Can be
bought separately)
11. Power cord
12. Removable mop-plate
13. Water tank.
14. Charging station D4000
1
2
3
4
5
6
78
11
10
9
12
13
14
12
INSTRUCTION MANUAL · ROBOT VACUUM
EN
PRODUCT OVERVIEW – VACUUM CLEANER
1. Sensor
2. ON/Off button
3. Recharge button
4. Cover
5. Side brush
6. Main brush
7. Charging electrodes
8. Main brush cover
9. Wet-mop holder
1
23
4
5
6
7
8
9
13
INNOBOT · RVC-D4000SL+, RVC-D4000SL, RVC-D4000AI
EN
1
2
3
4
5
6
7
8
9
10
11
12
13
1. Reset
2. Fastener
3. Water inlet
4. Water tank metal pole
5. Wet-mop
6. Filter screen
7. Indicator
8. Charging electrode
9. Air outlet
10. Dust inlet
11. Fastener
12. Lock
13. Dust bag
PRODUCT OVERVIEW – DETAILED
ROBOT VIBRATING WATER TANK
AUTO-EMPTY STATION
(Included in RVC-D4000SL+ or buy separately)
DUSTBOX
DUSTBAG
14
INSTRUCTION MANUAL · ROBOT VACUUM
EN
PRODUCT OVERVIEW – LIGHTS AND BUTTONS
Blue light is always on Standby / Normal operation /
Wi-Fi is connected
Blue light breaths Charging, power is more than 20%
Blue light flashes Firmware upgradein progress /Restoring
factory settings / Connecting to the network
Yellow light is always on WIFI is offline
Yellow light breaths Charging, power is lower than 20%
Yellow light flashes Recharging
Red light flashes Abnormal state
On/Off button Long press for 3s, power on or power off.
Short press, start or pause.
Recharging button In operation state, short press, robot pauses
cleaning. In pause state, short press start
recharging. In charging state, short press to
stop recharging.
15
INNOBOT · RVC-D4000SL+, RVC-D4000SL, RVC-D4000AI
EN
INSTALLATION
To install the charging station, place it against the wall, and connect the power
cord. Make sure there is enough space in front and on the sides of the charger.
To install the auto-empty station. Place the dustbin against the wall and connect
the power cord.
Note:
• Do not place the charger in direct sunlight.
• The auto-empty station requires more than 1.5-meter space in front and
more than 0.5-meter space on both sides.
• Make sure the power cord is not placed where the robot can drag it.
POWER ON AND CHARGE
Put the robot on the base and align the charging electrodes with charging
contact. For daily use, you can start intelligent recharge by short pressing the
button
• Robot can’t start up when it has low power. Please put it on the base to
recharge.
• Robot will start up automatically after connecting to the base and can’t be
shut down while recharging.
SWEEPING MODE
Open the cover, insert the dust box and press it down.
Note: Clean the dust box regularly in case of the dirt affecting the cleaning
effect.
16
INSTRUCTION MANUAL · ROBOT VACUUM
EN
MOPPING MODE
1. Insert the mop along the slot of the mop holder and stick it on the hook and
loop fastener.
2. Open the water tank cover, ll the water tank and then fasten the water tank
cover.
Note:
• Do not use detergents, disinfectants, solid cleaners or other cleaning
products, or inject hot water into the water tank in case of corrosion and
damage to the water tank.
• It is forbidden to shower or soak the water tank; The water tank metal pole
should be dry before performing a mopping task.
3. Push the water tank into the bottom of the robot, and it will make a “click”
sound when it is installed in place.
Note:
• When mopping the floor, please set up virtual walls or forbidden zones in the
carpet area.
• Before starting sweeping/mopping function, be sure to remove any water
accumulated on the floor.
Mop holder
Hook and loop
fastener Mop
Water tank metal pole
17
INNOBOT · RVC-D4000SL+, RVC-D4000SL, RVC-D4000AI
EN
APP USE
CLEANING MODE/LEVEL SELECTION
You can choose various cleaning modes and water flow rates.
DO NOT DISTURB MODE (DND)
When Do Not Disturb mode is activated, proceeding at breakout point,
scheduled cleaning and active voice reporting are unavailable in robot.
Do Not Disturb mode is activated by default during the period from 22:00 to
7:00. Do Not Disturb mode can be deactivated in App.
CLEANING MODE WITHOUT MAP
When no map is stored, the robot will start cleaning each zone by a square area
of 6m×6m. When a map is stored, the robot will start cleaning each room along
the route planned automatically and return to base after completion.
MEMORY MAP
When memory map is activated in the App, the robot will save and update the
map after nishing cleaning task and recharging successfully. After a map is
completed successfully, you can split or merge zones or name any room in the
App.
EDGE CLEANING MODE
When choosing edge cleaning mode in the App, the robot will automatically
recognize range of the area to clean, and start cleaning along the edges, and
return to base automatically after nishing cleaning.
SPECIFIED AREA CLEANING MODE
When an area to be cleaned is specied in the App, the robot will clean the
specied area. Note: During cleaning, the robot may go beyond a dened area,
remove any obstacle on the floor within dened area since denition of any area
will not ensure safe separation.
FIXED-POINT CLEANING MODE
When choosing xed-point cleaning and have selected a target point in the App,
the robot will route cleaning task and start cleaning within a rectangular area of
2m × 2m based on the target position dened in the map in App.
SCHEDULED CLEANING MODE
User can schedule a cleaning task in App, and robot will start the cleaning task
as scheduled and return to the base upon end of the task. Note: Any scheduled
cleaning task will not be executed during the time when Do Not Disturb mode is
activated.
18
INSTRUCTION MANUAL · ROBOT VACUUM
EN
VIRTUAL WALL/FORBIDDEN AREA
User can dene virtual wall/ restricted area in App which the robot will avoid
cleaning. Note: Before using this function, you have to store a map in the App.
Moving the robot or change of indoor environment may cause the original map
lost and any virtual wall/ restricted area unavailable.
RESET/RESTORE SYSTEM
• By long pressing the Reset button for 3 seconds, you will not only restore
factory settings, but also reset the rmware to the last version.
• By long pressing Reset button for 10 seconds, the machine will clear all
network connection information, map information, scheduled task and do-
not-disturb information, and customization information, and reset the suction
power to the default level.
Note: After resetting/restoring the system, the robot needs to reconnect the
APP, and the relevant settings in the APP are removed.
MAINTENANCE AND CLEANING
DUST BOX
1. Open the cover, press the dust box lock and take out the dust box
2. Dispose the trash in dust box, and clean the box with cleaning brush
3. Remove the dust box cover, take the lter screen out, dispose trash and clean
the screen.
19
INNOBOT · RVC-D4000SL+, RVC-D4000SL, RVC-D4000AI
EN
Note:
• It is recommended to clean the dust box at least once a week. Dry the dust
box and lter screen before use (at least 24 hours)
• Do not wash the dust box with water, it can damage electric components.
VIBRATING WATER TANK
1. As shown in the gure, press the tank fastener down, and draw the tank out
horizontally.
2. Turn the plastic tank cover, discharge any residual water in it and mount the
cover in place.
3. As shown in the gure, mount the tank properly.
SIDE BRUSH
1. Turn the robot over and remove the side brush xing screws.
2. Remove and clean the side brush.
3. Reinstall the side brush and tighten the screws.
20
INSTRUCTION MANUAL · ROBOT VACUUM
EN
Note: It is recommended to replace the side brush every 3-6 months to ensure
the cleaning effect.
MAIN BRUSH
1. Turn the robot over, press and hold the two release buttons to remove the
main brush cover.
2. Take out the main brush upwards.
3. Use the knife on the cleaning brush to cut the entangled hair on the main
brush and clean the main brush.
4. Put back the main brush and the main brush cover, and press the main brush
cover to install it in place.
Note: It is recommended to replace the main brush every 6-12 months to ensure
the cleaning effect.
BRUSH CLEANING METHOD
Use the included cleaning tool.
CLIFF SENSOR
Use a soft dry cloth to clean the cliff sensor every 3 months.
Main brush cover
Release keys
Main brush
Cut hair Clean the dirt
Cliff sensor
/
