ResMed HumidAire 3i Kasutusjuhend

www.resmed.com Waking people up to sleep

Reorder number: 33804/2 05 05

USER’S MANUAL

English

Svenska

Dansk

Norsk

Suomi

HumidAire 3i

™

HumidAire 3i

TM

A

B

12

4

D

1 4

1

2

566a

234

3

C

E

1

2

3

(a)

Component of 33804/2

ILLUSTRATIONS

ILLUSTRATIONER

ILLUSTRASJONER

KUVAT

Air outlet / Luftutsläpp /

Luftudtag / Luftuttak /

Ilmantuloaukko

Control dial /

Kontrollknapp /

Kontrolknap /

Kontrollskive / Säädin

Docking station /

Dockingstation /

Dockningstation /

Forankringsstasjon /

Liitäntäasema

Heater plate /

Värmeplatta / Varmeplade /

Varmeplate / Lämmityslevy

Latch / Spärrhake /

Klinke / Haspe /

Salpa

Cover / Framstycke / Dæksel /

Deksel / Kansi

Cover seal / Framstyckets försegling /

Tætning til dæksel / Dekselkapsling /

Kannen tiiviste

Connector seal / Kopplingsförsegling /

Tætning til kobling / Koblingsstykkekapsling /

Liitännän tiiviste

Water chamber /

Vannbeholder /

Vattenbehållare /

Vesisäiliö

REMOVING THE FRONT CAP (IF FITTED) / TA BORT FRONTKÅPAN (OM DEN

ÄR INPASSAD) / FJERNELSE AF FRONTDÆKSEL (HVIS RELEVANT) / SLIK TAR DU AV

FRONTDEKSLET (HVIS UTSTYRT MED) / ETUKANNEN IRROTTAMINEN (JOS SE ON

PAIKOILLAAN)

Front cap /

Lock på framsidan /

Frontdæksel /

Frontdeksel /

Etukansi

REMOVING AND STORING THE CONNECTOR PLUG / BORTTAGNING OCH

FÖRVARING AV KOPPLINGSKONTAKTEN / FJERNELSE OG OPBEVARING AF

KOBLINGSFORBINDELSEN / TA AV OG OPPBEVARE TILKOBLINGSPLUGGEN /

LIITÄNTÄTULPAN IRROTTAMINEN JA SÄILYTTÄMINEN

Connector plug / Kopplingskontakt /

Koblingsforbindelse / Tilkoblingsplugg / Liitäntätulppa

ATTACHING YOUR HUMIDAIRE 3i / SÄTTA FAST HUMIDAIRE 3i / PÅSÆTNING AF HUMIDAIRE 3i / KOBLE TIL HUMIDAIRE 3i-APPARATET /

HUMIDAIRE 3i -ILMANKOSTUTTIMEN LIITTÄMINEN

FILLING THE WATER CHAMBER / FYLLA VATTENBEHÅLLAREN / OPFYLDNING AF VANDBEHOLDER / FYLLE VANNBEHOLDEREN / VESISÄILIÖN TÄYTTÄMINEN

33804r2 illos.qxd 25/05/2005 2:53 PM Page 1

I

1 2

34

5

6

F H

3

56

9

1

4

10 min

G

2

3

5

4

UNDERSIDE VIEW / BILD UNDERIFRÅN / SET FRA UNDERSIDEN /

VISNING AV UNDERSIDE / NÄKYMÄ ALHAALTA

7

8

1

10 min

2

Large silver button /

Stor silverknapp /

Stor sølvknap /

Stor sølvfarget knapp /

Hopeanvärinen painike

Press button and pull apart / Tryck på knappen och dra isär /

Tryk på knappen og træk delene fra hinanden / Trykk inn knappen og

trekk fra hverandre / Paina painiketta ja vedä osat erilleen

STARTING YOUR TREATMENT / STARTA BEHANDLINGEN / INDLEDNING AF

BEHANDLINGEN / START AV BEHANDLING / HOIDON ALOITTAMINEN

Right key / Höger knapp /

Højre tast / Høyre tast /

Oikea näppäin

Up/Down keys /

Upp/Ner knappar /

Op/Ned-taster /

Opp/ned-taster /

Ylös/alas-näppäimet

Start/Stop key / Start/Stop knapp /

Start/Stop-tast / Start/Stans-tast /

Käynnistys/pysäytys-näppäin

Control dial /

Kontrollknapp /

Kontrolknap /Kontrollskive

/ Säädin

Indicator light / Ljusindikator /

Indikatorlys / Indikatorlampe /

Merkkivalo

Control panel / Kontrollpanel /

Kontrolpanel / Kontrollpanel /

Ohjauspaneeli

Left key / Vänster knapp /

Venstre tast / Venstre tast /

Vasen näppäin

DETACHING YOUR HUMIDAIRE 3i / TA BORT HUMIDAIRE 3i / FRAKOBLING AF HUMIDAIRE 3i /

FRAKOBLING AV HUMIDAIRE 3i-APPARATET / HUMIDAIRE 3i -ILMANKOSTUTTIMEN IRROTTAMINEN

DISASSEMBLING YOUR HUMIDAIRE 3i / TA ISÄR HUMIDAIRE 3i / DEMONTERING AF HUMIDAIRE 3i /

DEMONTERING AV HUMIDAIRE 3i-APPARATET / HUMIDAIRE 3i -ILMANKOSTUTTIMEN PURKAMINEN

RE-ASSEMBLING YOUR HUMIDAIRE 3i / SÄTTA IHOP HUMIDAIRE 3i /

SAMLING AF HUMIDAIRE 3i / SETTE SAMMEN HUMIDAIRE 3i-APPARATET IGJEN /

HUMIDAIRE 3i -ILMANKOSTUTTIMEN KOKOAMINEN

33804r2 illos.qxd 25/05/2005 2:54 PM Page 2

USER’S MANUAL 1

B

RUGERMANUAL 41

B

RUKSANVISNING 21

B

RUKERHÅNDBOK 61

HUMIDAIRE 3i

™

ENGLISHSVENSKANORSK DANSKSUOMI

KÄYTTÖOHJE 83

33804r2.book Page iii Wednesday, May 25, 2005 2:54 PM

Patents and designs pending.

HumidAire, HumidAire 3i, S8 and SmartStart are trademarks of ResMed Ltd and HumidAire is registered in

U.S. Patent and Trademark Office.

Manufactured by:

ResMed Ltd 1 Elizabeth MacArthur Drive Bella Vista NSW 2153 Australia

Tel: +61 (2) 8884 1000 or 1 800 658 189 (toll free) Fax: +61 (2) 8883 3114 Email: [email protected]

Distributed by:

ResMed Corp 14040 Danielson Street Poway CA 92064-6857 USA

Tel: +1 (858) 746-2400 or 1-800-424-0737 (toll free) Fax: +1 (858) 746-2900 Email: [email protected]

ResMed (UK) Limited 65 Milton Park Abingdon Oxfordshire OX14 4RX UK

Tel: +44 (1235) 862 997 Fax: +44 (1235) 831 336 Email: rece[email protected]

ResMed Asia Pacific Ltd 97 Waterloo Road North Ryde NSW 2113 Australia

Tel: +61 (2) 9886 5000 or 1 800 991 900 (toll free) Fax: +61 (2) 9889 1471 Email: [email protected]

ResMed Austria GmbH Purtscherstraße 18, 9500 Villach Österreich

Tel: 43 (4242) 430 830 Fax: +43 (4242) 430 830-4 Email: rece[email protected]

ResMed BV Nieuwe Parklaan 86, 2587 BV Den Haag Nederland

Tél: +31 (70) 358 6263 Fax: +31 (70) 358 4333 Email: recept[email protected]

ResMed Finland Niittykatu 6 FIN 02200 ESPOO Suomi

Puh: +358 9 8676820 Faksi: +358 9 86768222 Sähköposti: reception@resmed.fi

ResMed GmbH & Co. KG Fraunhoferstraße 16, 82152 Martinsried Deutschland

Tel: +49 (0) 89/99 01-00 Fax: +49 (0) 89/99 01-10 55 Email: [email protected]

ResMed Hong Kong Limited Room 1714, Miramar Tower 132-134 Nathan Road Tsim Sha Tsui Hong Kong

Tel: +852 2366 0707 Fax: +852 2366 4546 Email: receptio[email protected]

ResMed Japan Nihonbashi Hisamatsu Bldg. 4F, 2-28-1 Nihonbashi-Hamacho, Chuo-Ku, Tokyo 103-0007, Japan

Tel: +81 (3) 3662 5056 Fax: +81 (3) 3662 5040

ResMed Malaysia Sdn Bhd Suite E-10-20, Plaza Mon’t Kiara No. 2 Jalan 1/70C Mon’t Kiara 50480 Kuala Lumpur

Malaysia Tel: +60 3 6201 7177 Fax: +60 3 6201 2177 Email: reception@resmed.com.my

ResMed NZ Ltd PO Box 51-048 Pakuranga Auckland New Zealand

Tel:+64 274 737 633 Fax:+64 9 239 0193 Email: reception@resmed.co.nz

ResMed SA Parc de la Bandonnière 2, rue Maurice Audibert 69800 Saint-Priest France

Tél. : +33 (0) 4 37 251 251 Fax : +33 (0) 4 37 251 260 Email: [email protected]

ResMed Singapore Pte Ltd 238A Thomson Road #12-03/04, Novena Square, Tower A Singapore 307684

Tel: +65 6284 7177 Fax: +65 6284 7787 Email: reception@resmed.com.sg

ResMed Spain SL C/Arturo Soria, 245 28033 Madrid España

Tel: +34 (93) 5908154 Fax: +34 (93) 5908153 Email:angelo@resmed.es

ResMed Sweden AB Industrigatan 2 S-461 37 Trollhättan Sverige

Tel: +46 520 420 110 Fax: +46 520 397 15 Email: [email protected]

Labhardt AG Thannerstrasse 57 CH-4054 Basel Schweiz

Tel: +41 (061) 307 9711 Fax: +41 (061) 307 9722 Email: [email protected]

US DESIGNATED AGENT: ResMed Corp

EU AUTHORISED REPRESENTATIVE: ResMed (UK) Ltd

Internet: www.resmed.com

33804r2.book Page iv Wednesday, May 25, 2005 2:54 PM

ENGLISH

1

USER’S MANUAL

English

HumidAire 3i

™

33804r2.book Page 1 Wednesday, May 25, 2005 2:54 PM

2

CONTENTS

WELCOME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

WHAT IS THE HUMIDAIRE 3i? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Y

OUR RESPONSIBILITY 3

MEDICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

I

NTENDED USE 4

C

ONTRAINDICATIONS 4

W

ARNINGS 4

COMPONENTS OF YOUR HUMIDAIRE 3i . . . . . . . . . . . . . . . . . . . . . . . . . . 5

SETTING UP YOUR HUMIDAIRE 3i FOR USE . . . . . . . . . . . . . . . . . . . . . . . 5

R

EMOVING THE FRONT CAP (IF FITTED) 5

R

EMOVING AND STORING THE CONNECTOR PLUG 6

A

TTACHING YOUR HUMIDAIRE 3i 6

F

ILLING THE WATER CHAMBER 6

STARTING AND STOPPING TREATMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

S

TARTING YOUR TREATMENT 7

S

TOPPING YOUR TREATMENT 8

D

ETACHING YOUR HUMIDAIRE 3i 8

FREQUENTLY ASKED QUESTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

D

ISASSEMBLING YOUR HUMIDAIRE 3i 10

C

LEANING YOUR HUMIDAIRE 3i 11

R

EASSEMBLING YOUR HUMIDAIRE 3i 11

S

ERVICING 12

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

33804r2.book Page 2 Wednesday, May 25, 2005 2:54 PM

3

WELCOME

ENGLISH

WELCOME

Thank you for choosing the ResMed HUMIDAIRE 3i™ humidifier. The HUMIDAIRE 3i

is designed to humidify (moisten) the air delivered to your airway during CPAP

(continuous positive airway pressure) therapy. The H

UMIDAIRE 3i attaches to your

ResMed S8™ Series CPAP flow generator with a simple ‘click-in’ mechanism.

This user manual contains the information you need for the correct use of your

H

UMIDAIRE 3i.

WHAT IS THE HUMIDAIRE 3i?

The HUMIDAIRE 3i is designed to form a single unit with a ResMed CPAP flow

generator. The combined unit provides humidification during CPAP therapy, and can

make therapy more comfortable.

You may have experienced nasal congestion or dryness of the nose, mouth, or throat

during CPAP therapy. These symptoms are caused by dry climates, cold air

temperatures, the airflow delivered from your flow generator, or mouth leak. Moist air

may help relieve these symptoms of dryness.

Refer to your flow generator manual to see whether it is compatible with the

H

UMIDAIRE 3i. Contact your equipment supplier or ResMed office if you require

further information.

YOUR RESPONSIBILITY

You or the user of this system shall have sole responsibility and liability for any injury

to persons or damage to property resulting from:

• operation which is not in accordance with the operating instructions supplied

• maintenance or modifications carried out unless in accordance with authorised

instructions and by authorised persons.

Please read this manual carefully before use.

This manual contains special terms and icons that appear in the margins to draw your

attention to specific and important information.

• Warning alerts you to possible injury.

• Caution explains special measures for the safe and effective use of the device.

• Note is an informative or helpful note.

33804r2.book Page 3 Wednesday, May 25, 2005 2:54 PM

4

MEDICAL INFORMATION

INTENDED USE

The HUMIDAIRE 3i is indicated for humidification of the air delivered from the ResMed

S8 Series CPAP devices. The H

UMIDAIRE 3i is for use only as recommended by a

physician.

CONTRAINDICATIONS

The HUMIDAIRE 3i is contraindicated for use with patients whose upper (supraglottic)

airway has been bypassed. Please also refer to the relevant system manual for

contraindications associated with CPAP therapy.

WARNINGS

The following are general warnings. Specific warnings and cautions appear next to the

relevant instructions in the manual.

!

WARNINGS

• Use the HUMIDAIRE 3i only for its intended use as described in this manual.

• Make sure that the water chamber is empty and thoroughly dried before

transporting the H

UMIDAIRE 3i.

• The HUMIDAIRE 3i is designed only for use with specific ResMed CPAP devices.

Do not use the H

UMIDAIRE 3i with any other CPAP device.

• The HUMIDAIRE 3i should only be used with delivery tubes or accessories

recommended by ResMed. Connection of other delivery tubes or accessories

could result in injury, or damage to the device.

• The HUMIDAIRE 3i, including the associated tubing, is for single-patient use and

must not be re-used on another person. This is to avoid the risk of cross-infection.

• Always place the HUMIDAIRE 3i device lower than the level of the patient. If it is

placed at or above the level of the patient, heated water may flow down the air

tubing and into the mask.

• There exists the possibility that if the device is placed above the level of the patient

and is tipped over, or if the tubing is filled with condensate, the mask might fill with

water. The H

UMIDAIRE 3i should therefore be used with caution in patients who

are unable to guard their airways, or are unable to pull the mask off, for example

following a stroke. Attention should be given to the relative risks and benefits.

• Do not attempt to dismantle the HUMIDAIRE 3i docking station. There are no

user-serviceable parts inside. Repairs and internal servicing should only be

performed by an authorised service agent.

• Take care when handling the HUMIDAIRE 3i. The heater plate and the water in the

water chamber may be hot.

• If liquids are inadvertently spilled into or on the HUMIDAIRE 3i docking station,

unplug the CPAP device from the power outlet. Disconnect the docking station

from the CPAP device and allow the docking station to drain and dry before using.

33804r2.book Page 4 Wednesday, May 25, 2005 2:54 PM

5

COMPONENTS OF YOUR HUMIDAIRE 3i

ENGLISH

• Do not operate the HUMIDAIRE 3i if the CPAP device has a damaged power cord

or plug.

• Do not operate the HUMIDAIRE 3i if it is not working properly or if any part of it

has been dropped or damaged.

• Keep the CPAP device power cord away from heated surfaces.

• Do not drop or insert any object into any opening or tubes.

• Do not use the HUMIDAIRE 3i in the presence of flammable or explosive

materials.

• Explosion hazard—do not use in the vicinity of flammable anaesthetics.

• If oxygen is used with this device, the oxygen flow must be turned off when the

device is not operating.

If oxygen has been left on, turn off the flow generator, then wait 30 minutes before

turning on the flow generator again.

Explanation: When the CPAP device is not in operation and the oxygen flow is

left on, oxygen delivered into the air delivery tubing may accumulate within the

CPAP machine enclosure and create a risk of fire. This applies to most types of

CPAP machines.

• Oxygen supports combustion. Oxygen should not be used while you are

smoking or in the presence of an open flame.

• Always ensure airflow is being generated by the device before the oxygen

supply is turned on.

• Always turn the oxygen supply off before stopping the airflow from the device.

Note: At a fixed rate of supplemental oxygen flow, the inhaled oxygen concentration

will vary, depending on where the oxygen is introduced, the pressure settings, patient

breathing pattern, mask selection and leak rate.

COMPONENTS OF YOUR HUMIDAIRE 3i

Please refer to the illustrations in section A of the illustration sheet.

SETTING UP YOUR HUMIDAIRE 3i FOR USE

!

WARNING

Make sure your flow generator is switched off at the power outlet before

connecting the HumidAire 3i.

REMOVING THE FRONT CAP (IF FITTED)

Please refer to the illustrations in section B of the illustration sheet.

Your flow generator may be fitted with a front cap (B-1). Before you can attach the

H

UMIDAIRE 3i, press the button underneath the front cap (B-2) and pull it away from

the body of your flow generator (B-3 & B-4).

33804r2.book Page 5 Wednesday, May 25, 2005 2:54 PM

6

Notes

• To replace the front cap, align it with your flow generator (B-4) and push it firmly until it

clicks into place.

• Remember to take the front cap with you when travelling, in case you need CPAP

therapy without a humidifier.

REMOVING AND STORING THE CONNECTOR PLUG

Please refer to the illustrations in section C of the illustration sheet.

Before attaching the H

UMIDAIRE 3i, remove the connector plug from your flow

generator (C-1) and attach it to the back of the docking station (C-2).

ATTACHING YOUR HUMIDAIRE 3i

Please refer to the illustrations in section D of the illustration sheet.

1 Align your HUMIDAIRE 3i with your flow generator (D-1) and push them together

until they click into place (D-2).

!

WARNING

• The HumidAire 3i docking station should only be connected or disconnected

when the water chamber is empty.

• Water must be prevented from entering your flow generator. Do not transport

the flow generator with the HumidAire 3i attached.

2

Insert the power cord into the socket at the rear of your flow generator. Plug the other

end of the power cord into a power outlet (D-3).

Note: If your flow generator is powered via the DC input, the HumidAire 3i is not powered

and humidification output will be reduced.

3

Place the combined unit on a firm, level surface near your bed at a level lower than

your sleeping position. Ensure the surface is not sensitive to heat and/or moisture, or

use a protective mat.

!

CAUTION

Be careful not to place the unit where it can be bumped into and knocked over.

4

Connect one end of the air tubing firmly onto the air outlet of your HUMIDAIRE 3i

and the other end to your mask (D-4).

FILLING THE WATER CHAMBER

Please refer to the illustrations in section E of the illustration sheet.

!

WARNING

Take care when handling your HumidAire 3i. The water and the water chamber

base may both be hot. Allow ten minutes for the heater plate and any excess water

to cool.

1 Release the cover latch (E-1) and lift the cover until it rests in the upright position (E-2).

33804r2.book Page 6 Wednesday, May 25, 2005 2:54 PM

7

STARTING AND STOPPING TREATMENT

ENGLISH

2

Remove the water chamber (E-3) and carefully fill it with fresh, clean water (E-4). Make

sure you keep the level of the water under the maximum water level mark (E-4a).

Always ensure that the water chamber is clean. See “Cleaning and Maintenance” on

page 10.

!

WARNING

Do not overfill the water chamber, as water may enter your flow generator and air

tubing.

!

CAUTION

Do not use any additives (eg scented oils and perfumes). They may reduce the

humidification output of the HumidAire 3i and/or cause deterioration of the water

chamber materials.

3

Carefully place the filled water chamber into the humidifier docking station (E-5) and

latch the cover (E-6 & E-6a).

The H

UMIDAIRE 3i is now ready for use.

STARTING AND STOPPING TREATMENT

STARTING YOUR TREATMENT

Please refer to the illustration in section F of the illustration sheet.

1 When your HUMIDAIRE 3i is attached and the flow generator is powered, the

indicator light lights up on the H

UMIDAIRE 3i. A prompt for the Warm-Up feature

(not available on all models) may appear.

When activated, this feature allows the water to warm up before you start treatment.

2

If the Warm-Up feature is available, use it to pre-heat the water before starting your

treatment. Skip this step if you wish to start treatment immediately.

WARM-UP FEATURE (NOT AVAILABLE IN ALL MODELS)

Note: Check your flow generator user’s manual to see if this feature is available.

To start the Warm-Up feature:

i. Select Warmup by pressing the Right key on the control panel.

The following message is displayed for 2 seconds:

ii. After 2 seconds the WARMING screen is displayed.

RAMP: 10min

menu



warmup

HUMIDIFIER

WARMING

menu exit

33804r2.book Page 7 Wednesday, May 25, 2005 2:54 PM

8

iii. While your HUMIDAIRE 3i is in Warm-Up mode you can:

• Start treatment at any time by pressing the Start/Stop key.

• Access the menus by pressing Menu (Left key).

• Stop the Warm-Up feature at any time by pressing Exit (Right key).

The Warm-Up feature will automatically turn off after 30 minutes if treatment has not

started.

3

Turn the humidity control dial to the desired setting. The setting switches heated

humidification off and delivers minimum humidification. The indicator light will remain

lit to indicate standby mode. A setting of 6 ( ) delivers maximum humidification.

We recommend that you initially set the control dial to 3 ( ). If necessary, adjust the

control dial up or down to find the setting that is most comfortable and effective for

you. You can adjust the humidity setting at any time.

The aim is to have moist air delivered to your mask but to avoid condensation forming

in the air tubing. The temperature and humidity of the surrounding air will affect the

setting you need.

See “Frequently Asked Questions” for further tips on the correct humidity setting.

4

Fit your mask as described in your mask user instructions.

5

Press the Start/Stop key on the control panel. Alternatively, if your flow generator

has the SmartStart™ function available, simply breathe into your mask and air should

begin to flow.

Note: During operation, the indicator light becomes brighter to indicate that the heating

element is active. Your HumidAire 3i has a rapid heating element which allows very short

heating times. Do not be concerned if the light only brightens very briefly.

6

Lie down and arrange the air tubing so that it is free to move if you turn in your sleep.

!

WARNING

Do not leave an excessive length of air tubing around the top of your bed. It could

twist around your head or neck while you are sleeping.

STOPPING YOUR TREATMENT

To stop your treatment at any time, remove your mask and press the Start/Stop key.

Alternatively, if your flow generator has the SmartStart function available, simply

remove your mask and treatment will end.

Some flow generators continue to blow air gently after you have stopped your

treatment. This can continue for up to one hour to assist the heater plate in cooling.

However, you can unplug the device from the power outlet at any time and allow the

heater plate to cool without airflow.

DETACHING YOUR HUMIDAIRE 3i

Please refer to the illustrations in section G of the illustration sheet.

33804r2.book Page 8 Wednesday, May 25, 2005 2:54 PM

9

FREQUENTLY ASKED QUESTIONS

ENGLISH

1 Unplug the power cord from the power outlet (G-1).

!

WARNING

Take care when handling your HumidAire 3i. The water and the water chamber

base may both be hot. Allow ten minutes for the heater plate and any excess water

to cool (G-2).

2

Remove the water chamber from the docking station (G-3).

3

Press the large silver button located midway underneath the docking station

(G-4) and pull the H

UMIDAIRE 3i and flow generator apart (G-5).

Note: Re-attach the connector plug firmly to your flow generator.

FREQUENTLY ASKED QUESTIONS

WHY IS THERE CONDENSATION IN MY MASK AND/OR AIR TUBING?

You may experience excessive condensation in your mask or air tubing. This may occur

seasonally, particularly when the room temperature is low or cool air is circulating

around the tube. Turn the control dial down to a lower setting until the condensation

decreases.

You may have to adjust your humidity setting from season to season.

DO I HAVE TO USE DISTILLED WATER IN THE WATER CHAMBER?

Using distilled water will maximise the life of the water chamber and reduce mineral

deposits. See “Cleaning your HumidAire 3i” on page 11 for further details.

WHAT IF I STILL HAVE SYMPTOMS OF DRYNESS?

If you still experience symptoms of dryness, then your humidity setting may be set too

low to be effective. Gradually turn the humidity control dial up over a few nights until

the symptoms disappear.

If you are still experiencing symptoms of dryness, even after increasing the humidity

setting, you may be breathing through your mouth. Mouth breathing or mouth leaks

cause drying and irritation of the upper airway. If this is a problem, a full face mask or

chin strap may help. Consult your clinician or equipment supplier for details.

Large silver button

UNDERSIDE VIEW

33804r2.book Page 9 Wednesday, May 25, 2005 2:54 PM

10

CLEANING AND MAINTENANCE

You should regularly carry out the cleaning and maintenance of the water chamber,

cover and cover seal as described in this section.

DISASSEMBLING YOUR HUMIDAIRE 3i

Please refer to the illustrations in section H of the illustration sheet.

!

WARNING

Beware of electrocution. Do not immerse your flow generator, docking station or

power cord in water. Always unplug the device before cleaning and be sure that it

is dry before plugging it back in.

1 Unplug the power cord from the power outlet (H-1).

!

WARNING

Take care when handling your HumidAire 3i. The water and the water chamber

base may both be hot. Allow ten minutes for the heater plate and any excess water

to cool (H-2).

2

Remove the water chamber from the docking station (H-3) and discard any excess

water (H-4).

3

Detach the air tubing from the air outlet (H-5).

4

Gently flex one cover arm away and up from the docking station until the cover

detaches completely (H-6 to H-8). Peel the cover seal away from the cover (H-9).

TUB PLATE

The tub plate should not be removed from the water chamber. If removed, replace

the tub plate by:

i. Turning the water chamber base upside down.

ii. As shown below, position the tub plate so that the open side is facing down. Then

firmly press the tub plate down into the water chamber.

!

CAUTION

The water chamber may leak if the tub plate is refitted incorrectly.

Note: The tub plate will not fit into the water chamber if it is facing up. Before fitting the

tub plate, make sure the O-ring is fitted snugly inside the groove of the tub plate.

tub plate

33804r2.book Page 10 Wednesday, May 25, 2005 2:54 PM

11

CLEANING AND MAINTENANCE

ENGLISH

CLEANING YOUR HUMIDAIRE 3i

!

CAUTION

• Do not use any of the following to clean any part of the HumidAire 3i. These

solutions may cause damage and reduce the life of the product.

• bleach, chlorine-, alcohol- or ammonia-based solutions

• moisturising, antibacterial or glycerine based soaps

• water softening and unapproved descaling agents.

• Do not wash the water chamber in a dishwasher.

WATER CHAMBER

DAILY

Wash the water chamber and tubing in warm water, using a mild detergent

(see previous caution). Rinse them thoroughly with clean water and allow them to dry

away from direct sunlight.

WEEKLY

Inspect the water chamber for wear and deterioration. Replace the water chamber if

any component has cracked, become cloudy or pitted. Replace immediately if there is

any leaking from the water chamber.

If you notice white powder or deposits in the water chamber:

i. Fill the water chamber to the maximum water level mark with a solution of one

part vinegar to ten parts water.

ii. Let the solution soak for ten minutes.

iii. Discard the solution and rinse the water chamber with clean water.

COVER AND COVER SEAL

Inspect the cover and cover seal weekly for wear and deterioration. Replace any

damaged parts. When required, wash the cover and cover seal in warm water, using a

mild detergent (see previous caution). Rinse them thoroughly with clean water and

allow them to dry away from direct sunlight.

DOCKING STATION

Periodically wipe the outside of the docking station (including the connector seal) with

a damp cloth.

REASSEMBLING YOUR HUMIDAIRE 3i

Please refer to the illustrations in section I of the illustration sheet.

Reassemble the parts when they are clean and dry.

1 Align the cover seal to the guides on the cover (I-1) and press along the edges to

ensure it is fitted properly (I-2).

2

Put one cover arm into its pivot point on the docking station (I-3) and gently flex the

other arm into its corresponding point (I-4 & I-5).

33804r2.book Page 11 Wednesday, May 25, 2005 2:54 PM

12

The cover should be able to open and close freely while securely attached to the

docking station.

3

Replace the water chamber in the humidifier docking station (I-6).

SERVICING

With normal use of a HUMIDAIRE 3i, the water chamber needs to be replaced every

two years.

This product (H

UMIDAIRE 3i) should be inspected by an authorised ResMed Service

Centre 5 years from the date of manufacture. Prior to this, the device is intended to

provide safe and reliable operation provided that it is operated and maintained in

accordance with the instructions provided by ResMed. Applicable ResMed warranty

details are provided with the device at the time of original supply. Of course, as with

all electrical devices, if any irregularity becomes apparent, you should exercise caution

and have the device inspected by an authorised ResMed Service Centre.

33804r2.book Page 12 Wednesday, May 25, 2005 2:54 PM

13

TROUBLESHOOTING

ENGLISH

TROUBLESHOOTING

If there is a problem, try the following suggestions. If the problem cannot be solved,

contact your equipment supplier or ResMed. Do not attempt to open the unit.

!

WARNING

Service and repair should only be performed by an authorised service agent.

Problem Possible Cause Solution

Device not working

(no display on LCD

screen and/or

indicator light not

lighting up)

Power cord is not plugged

in properly.

Faulty power outlet.

Flow generator and

docking station not

connected correctly.

Check that the power cord is plugged

firmly into the power outlet and the

switch (if available) is on at the outlet.

Try another power outlet.

Check that the docking station is

securely attached to the flow generator.

Indicator light

flickering

Indicator light periodically

becomes brighter to

indicate that the heating

element is active.

• Your HumidAire 3i has a rapid

heating element which allows very

short heating times. Do not be

concerned if the light only brightens

very briefly.

• Turn the dial to the setting to

switch heated humidification off. The

indicator light will remain lit to

indicate standby mode.

Indicator light is

permanently dull

and/or air does not

feel warm

HumidAire 3i reflector (see

illustration C-2a) is dirty.

Clean the reflector with a damp cloth.

Leaking water

chamber

The water chamber may be

damaged or cracked.

Cover is not attached

correctly.

Contact your supplier for a replacement.

Make sure the cover is fitted correctly.

33804r2.book Page 13 Wednesday, May 25, 2005 2:54 PM

14

No/low air flow The air tubing is not

connected properly.

The air tubing is blocked,

pinched or punctured.

The flow generator is not

working correctly.

The water chamber is

overfilled.

The cover is not latched

correctly.

The cover seal is not fitted

correctly.

Condensation is forming in

the air tube.

Connect the air tubing as described in

“Setting Up your HumidAire 3i For Use”

on page 5.

Unblock or free the air tubing. Check the

air tubing for punctures.

See the Troubleshooting section in the

flow generator manual.

Make sure that the water level is not

above the maximum water level mark.

Make sure the cover is latched onto the

docking station correctly.

Make sure the cover seal is facing the

right way up and fitted securely.

• Turn the control dial down.

• Insulate the air tubing.

Water splashing on

your face

The water chamber is

overfilled.

Condensation is forming in

the air tube and mask.

Empty some water from the water

chamber.

• Turn the control dial down.

• Insulate the air tubing.

Air does not feel

moist

The control dial is set too

low.

HumidAire 3i heating

element is not working.

Turn the control dial up.

Contact your equipment supplier.

Air too moist Control dial is set too high.

High relative humidity in

your room.

Turn the control dial down.

Adjust your humidity setting.

White powder or

deposits in the water

chamber

The water leaves scaly

mineral deposits.

• Use distilled water.

• To remove these mineral deposits, see

“Cleaning your HumidAire 3i” on

page 11.

Problem Possible Cause Solution

33804r2.book Page 14 Wednesday, May 25, 2005 2:54 PM

15

TECHNICAL SPECIFICATIONS

ENGLISH

TECHNICAL SPECIFICATIONS

PERFORMANCE

Maximum heater plate temperature: 85°C

Temperature cut-out: 93°C

Maximum output humidity: 95% relative humidity (control dial set to maximum setting,

flow rate 50 L/min, ambient temperature of 20°C, ambient relative humidity of 40%).

Maximum gas temperature: 41°C

DIMENSIONS (H X W X D)

Docking station and water chamber: 118 mm x 170 mm x 212 mm

WEIGHT

Docking station and unfilled water chamber: 670 g

Water capacity to maximum fill line: 385 mL

POWER SUPPLY

Input range for RESMED S8 flow generator with HUMIDAIRE 3i: 100–240V, 50/60Hz;

110V, 400Hz; 2.5A <140 VA (110 W) (maximum power consumption). Instantaneous

peak power consumption <340 VA.

Actual average power consumption will vary, depending on factors such as

temperature setting, set pressure, the use of accessories, height above sea level and

ambient temperature.

Maximum heater element power: 85 W.

HOUSING CONSTRUCTION

Docking station: Flame retardant engineering thermoplastic, plated cast aluminium.

Water chamber: Injection molded plastic, stainless steel.

ENVIRONMENTAL CONDITIONS

Operating temperature: +5°C to +40°C

Operating humidity: 10–95% non-condensing

Storage and transport temperature: -20°C to +60°C

Storage and transport humidity: 10–95% non-condensing

IEC 60601-1 CLASSIFICATION

Class II (double insulation)

Type CF

ELECTROMAGNETIC COMPATIBILITY

Please refer to your flow generator user's manual for details.

Note: The manufacturer reserves the right to change these specifications without notice.

33804r2.book Page 15 Wednesday, May 25, 2005 2:54 PM

Leht laadib ...

ResMed HumidAire 3i Kasutusjuhend

See käsiraamat sobib ka

ResMed HumidAire 3i Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid