Makita DLM537 Kasutusjuhend

DLM537

EN Cordless Lawn Mower INSTRUCTION MANUAL 8

SV Batteridriven gräsklippare BRUKSANVISNING 20

NO Batteridrevet gressklipper BRUKSANVISNING 32

FI Akkukäyttöinen

ruohonleikkuri KÄYTTÖOHJE 44

DA Akku-plæneklipper BRUGSANVISNING 55

LV Bezvada zāles pļaujmašīna LIETOŠANAS INSTRUKCIJA 67

LT Belaidė vejapjovė NAUDOJIMO INSTRUKCIJA 79

ET Juhtmeta muruniiduk KASUTUSJUHEND 91

RU Аккумуляторная

Газонокосилка РУКОВОДСТВО ПО

ЭКСПЛУАТАЦИИ 102

2

1

Fig.1

1

Fig.2

3

4

5

2

1

Fig.3

12

Fig.4

1

Fig.5

3

1

2

Fig.6

1

Fig.7

1

Fig.8

Fig.9

Fig.10

1

Fig.11

1

Fig.12

1

2

3

Fig.13

4

1

2

Fig.14

1

2

Fig.15

1

2

Fig.16

1

2

3

Fig.17

1

Fig.18

1

Fig.19

1

2

Fig.20

5

13

4

56

2

Fig.21

1 2

Fig.22

1

Fig.23

1

Fig.24

1

2

3

Fig.25

1

Fig.26

1

Fig.27

6

1

2

Fig.28

1

Fig.29

1

2

Fig.30

Fig.31

Fig.32

12 3

Fig.33

Fig.34

7

Fig.35

1

23

Fig.36

1

Fig.37

12

Fig.38

2

1

3

Fig.39

3

2

4

1

Fig.40

8ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: DLM537

Mowing width (blade diameter) 534 mm

No load speed Normal mode 2,800 min-1

Noise reduction mode 2,300 min-1

Part number of replacement

mower blade

Straight mower blade 191D52-7 / 191W87-2

Mulching blade 191Y65-4

Dimensions

(L x W x H)

L: 1,655 mm to 1,740 mm

W: 590 mm

H: 990 mm to 1,100 mm

Traveling speed 2.5 - 5.0 km/h

Rated voltage D.C. 36 V

Net weight

When straight mower blade is installed

42.6 - 46.1 kg

When mulching blade is installed

42.6 - 46.1 kg

Protection degree IPX4

•

Due to our continuing program of research and development, the specications herein are subject to change without notice.

• Specications may dier from country to country.

• The weight may dier depending on the attachment(s), including the battery cartridge. The lightest and heavi-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B

Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /

DC18SH

•

Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

and chargers may cause injury and/or re.

WARNING: Do not use a corded power supply such as battery adapter or portable power pack with

this machine. The cable of such power supply may hinder the operation and result in personal injury.

Symbols

The followings show the symbols which may be used

for the equipment. Be sure that you understand their

meaning before use.

Take particular care and attention.

Read instruction manual.

Danger; be aware of thrown objects.

The distance between the tool and

bystanders must be at least 15 m.

Never put your hands and feet near the

blade under the mower. Blades continue to

rotate after the motor is switched o.

Remove the lock key before inspecting,

adjusting, cleaning, servicing, leaving and

storing the mower.

Electrical hazard. Contact with water can

cause electric shock.

Do not pour water.

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical

and electronic equipment, accumulators

and batteries may have a negative impact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household waste!

In accordance with the European Directive

on waste electrical and electronic equipment

and on accumulators and batteries and

waste accumulators and batteries, as well as

their adaptation to national law, waste elec-

trical equipment, batteries and accumulators

should be stored separately and delivered

to a separate collection point for municipal

waste, operating in accordance with the

regulations on environmental protection.

This is indicated by the symbol of the

crossed-out wheeled bin placed on the

equipment.

9ENGLISH

Guaranteed sound power level according

to EU Outdoor Noise Directive.

Sound power level according to Australia

NSW Noise Control Regulation.

Intended use

The machine is intended for lawn mowing.

Noise

The typical A-weighted noise level determined accord-

ing to EN60335-2-77:

NOTE: The values have been measured with the

mower equipped with the straight mower blade or

mulching blade.

Sound pressure level (LpA) : 81.2 dB(A)

Sound power level (LWA) : 92.2 dB (A)

Uncertainty (K) : 3 dB(A)

NOTE: The declared noise emission value(s) has

been measured in accordance with a standard test

method and may be used for comparing one tool with

another.

NOTE: The declared noise emission value(s)

may also be used in a preliminary assessment of

exposure.

WARNING: Wear ear protection.

WARNING: The noise emission during actual

use of the power tool can dier from the declared

value(s) depending on the ways in which the

tool is used especially what kind of workpiece is

processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

o and when it is running idle in addition to the

trigger time).

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN60335-2-77:

NOTE: The values have been measured with the

mower equipped with the straight mower blade or

mulching blade.

Vibration emission (ah) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

NOTE: The declared vibration total value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also

be used in a preliminary assessment of exposure.

WARNING: The vibration emission during

actual use of the power tool can dier from the

declared value(s) depending on the ways in which

the tool is used especially what kind of workpiece

is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

o and when it is running idle in addition to the

trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Read all safety warnings and

all instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

Training

1. Read the instructions carefully. Be familiar

with the controls and the proper use of the

mower.

2. Never allow children or people unfamiliar with

these instructions to use the mower. Local

regulations can restrict the age of the operator.

3. Never operate the mower while people, espe-

cially children, or pets are nearby.

4. Keep in mind that the operator or user is

responsible for accidents or hazards occurring

to other people or their property.

5. Children should be supervised to ensure that

they do not play with the mower.

6. Physical condition - Do not operate mower

while under the inuence of drugs, alcohol, or

any medication.

Preparation

1.

While operating the mower, always wear sub-

stantial footwear and long trousers. Do not

operate the mower when barefoot or wearing

open sandals. Avoid wearing clothing or jewelry

that is loose tting or that has hanging cords or

ties. They can be caught in moving parts.

2. Before use, always visually inspect the mower

for damaged, missing or misplaced guards or

shields.

3. Be sure the area is clear of other people before

mowing. Stop mower if anyone enters the area.

10 ENGLISH

4. Do not insert the lock key into mower until it is

ready to be used.

5. Always wear protective goggles to protect

your eyes from injury when using power tools.

The goggles must comply with ANSI Z87.1 in

the USA, EN 166 in Europe, or AS/NZS 1336

in Australia/New Zealand. In Australia/New

Zealand, it is legally required to wear a face

shield to protect your face, too.

It is an employer's responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

6. Check the blades or blade bolts carefully for

cracks or damage before operation. Replace

cracked or damaged blades or blade bolts

immediately.

7. Remove foreign matters such as rocks, wire,

bottles, bones and large sticks from the work

area before mowing to prevent personal injury

or damage to the mower.

8. Objects struck by the mower blade can cause

severe injuries to persons. The lawn should

always be carefully examined and cleared of

all objects prior to each mowing.

9. Watch for holes, ruts, bumps, rocks, or other

hidden objects. Uneven terrain could cause a slip

and fall accident. Tall grass can hide obstacles.

10.

Do not insert or remove the lock key in the rain.

11. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as a dust mask, non-skid safety shoes, hard hat or

hearing protection used for appropriate conditions

will reduce personal injuries.

Operation

1. Do not overreach. Keep the balance at all

times. Always be sure of the footing on slopes.

Walk, never run.

2. Stop the mower and remove the lock key, and

make sure that all moving parts have come to

a complete stop:

- whenever you leave the mower,

- before clearing blockages or unclogging chute,

- before checking, cleaning or working on the

mower,

- after striking a foreign object. Inspect the

mower for damage and make repairs before

restarting and operating the mower,

- whenever the mower starts vibrating

abnormally.

3. Never operate the mower with defective

guards or shields, or without safety devices,

for example deectors and/or grass basket, in

place.

4. Avoid using the mower in bad weather con-

ditions especially when there is a risk of

lightning.

5. Wear eye protection and stout shoes at all

times while operating the mower.

6. Operate the mower only in daylight or in good

articial light.

7. Switch on the mower carefully according to

instructions and with feet well away from the

blade(s).

8. Take care against injury to feet and hands from

the mower blades.

9. Always ensure that the ventilation openings

are kept clear of debris.

10. Mow across the face of slopes, never up and

down. Exercise extreme caution when chang-

ing direction on slopes. Do not mow exces-

sively steep slopes.

11. Use extreme caution when reversing or pulling

the mower towards you.

12. Stop the blade(s) if the mower has to be tilted

for transportation when crossing surfaces

other than grass, and when transporting the

mower to and from the area to be used.

13. Do not tilt the mower when switching on the

motor, except if the mower has to be tilted

for starting. In this case, do not tilt it more

than absolutely necessary and lift only the

part, which is away from the operator. Always

ensure that both hands are in the operating

position before returning the mower to the

ground.

14. Do not put hands or feet near or under rotating

parts. Keep clear of the discharge opening at

all times.

15. Do not transport the mower while the mower is

turned on.

16. Avoid operating the mower in wet grass.

17. Always keep a rm hold on the handle.

18. Don't grasp the exposed cutting blades or

cutting edges when picking up or holding the

mower.

19. Keep hands and feet away from rotating

blades. Caution - Blades coast after the mower

is switched o.

20. Stop operation immediately if you notice

anything unusual. Switch o the mower and

remove the lock key. Then inspect the mower.

21. Never attempt to make cutting height adjust-

ments while mower is running if the mower

has cutting height adjustment feature.

22. Release switch lever and wait for blade rota-

tion to stop before crossing driveways, walks,

roads, and any gravel-covered areas. Also

remove the lock key if you leave the mower,

reach to pick up or remove something out of

your way, or for any other reason that may

distract you from what you are doing.

11 ENGLISH

23. If the mower strikes a foreign object, follow

these steps:

- Stop the mower, release the switch lever and

wait until the blade comes to a complete stop.

- Remove the lock key and the battery cartridge.

- Thoroughly inspect the mower for any

damage.

- Replace the blade if it is damaged in any way.

Repair any damage before restarting and con-

tinuing to operate the mower.

24. Do not start the mower when standing in front

of the discharge opening.

25. If the mower starts to vibrate abnormally

(check immediately)

- inspect for damage,

- replace or repair any damaged parts,

- check for and tighten any loose parts.

26. Never direct discharged material toward

anyone. Avoid discharging material against a

wall or obstruction. Material may ricochet back

toward the operator. Stop the blade when crossing

gravel surfaces.

27. Do not pull the mower backwards unless

absolutely necessary. When you are compelled

to back the mower from a fence or other similar

obstruction, look down and behind before and

while moving backwards.

28. Shut the motor o and wait until the blade

comes to a complete stop before removing the

grass catcher. Beware that the blades coast after

turn o.

29. When you use the machine on muddy ground,

wet slope, or slippery place, pay attention to

your footing.

30. Avoid working in poor environment where

increased user fatigue is expected.

31. Do not use the machine in bad weather where

visibility is limited. Failure to do so may cause

fall or incorrect operation due to low visibility.

32. Do not submerge the machine into a puddle.

33. When wet leaves or dirt adhere to the suc-

tion mouth (ventilation window) due to rain,

remove them.

34. Do not use the machine in the snow.

35. If the cut-o grass is wet, it is likely to be

clogged inside of the machine. Check the con-

dition of the machine regularly, and remove the

adhered grass as necessary.

36. When operating the machine, pay attention to

piping and wiring.

37. Do not use a corded power supply such as bat-

tery adapter or portable power pack with this

machine. The cable of such power supply may

hinder the operation and result in personal injury.

Maintenance and storage

1. Replace worn or damaged parts for safety.

Use only genuine replacement parts and

accessories.

2. Inspect and maintain the mower regularly.

3. When not in use, store the mower out of the

reach of children.

4. Keep all nuts, bolts, and screws tight to

be sure the equipment is in safe working

condition.

5. Check the grass basket frequently for wear or

deterioration. For storage, always make sure

the grass basket is empty. Replace a worn

grass basket with a new factory replacement

for safety.

6. Use only the manufacturer genuine blades

specied in this manual.

7. Be careful during adjustment of the mower

to prevent entrapment of the ngers between

moving blades and xed parts of the mower.

8. Check the blade mounting bolt at frequent

intervals for proper tightness.

9. Always allow the mower to cool down before

storing.

10. When servicing the blades be aware that, even

though the power source is switched o, the

blades can still be moved.

11. Never remove or tamper with safety devices.

Check their proper operation regularly. Never

do anything to interfere with the intended

function of a safety device or to reduce the

protection provided by a safety device.

12. Do not leave the machine unattended outdoors

in the rain.

13. Do not wash the machine with high pressure

water.

14. When washing the machine, be sure to remove

the battery and lock key and close the battery

cover, and pour water toward the bottom of the

machine to which the blade is attached.

15. When storing the machine, avoid direct sun-

light and rain, and store it in a place where it

does not get hot or humid.

16. Perform inspection or maintenance in a place

where rain can be avoided.

17. After using the machine, remove the adhered

dirt and dry the machine completely before

storing. Depending on the season or the area,

there is a risk of malfunction due to freezing.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of re

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and re.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a re.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause

irritation or burns.

5. Do not use a battery pack or tool that is dam-

aged or modied. Damaged or modied batteries

may exhibit unpredictable behaviour resulting in

re, explosion or risk of injury.

12 ENGLISH

6. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or tem-

perature above 130 °C may cause explosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outside the specied range may damage the

battery and increase the risk of re.

Electrical and battery safety

1. Do not dispose of the battery(ies) in a re.

The cell may explode. Check with local codes for

possible special disposal instructions.

2. Do not open or mutilate the battery(ies).

Released electrolyte is corrosive and may cause

damage to the eyes or skin. It may be toxic if

swallowed.

3. Do not charge battery in rain, or in wet

locations.

4. Do not charge the battery outdoors.

5. Do not handle charger, including charger plug,

and charger terminals with wet hands.

6. Do not replace the battery in the rain.

7. Do not wet the terminal of battery with liquid

such as water, or submerge the battery. Do not

leave the battery in the rain, nor charge, use,

or store the battery in a damp or wet place. If

the terminal gets wet or liquid enters inside of bat-

tery, the battery may be short circuited and there is

a risk of overheat, re, or explosion.

8. Avoid dangerous envionment. Don't use the

tool in dump or wet locations or expose it to

rain. Water entering the tool will increase the

risk of electric shock.

9. If the battery cartridge gets wet, drain the

water inside and then wipe it with a dry cloth.

Dry the battery cartridge completely in a dry

place before use.

10. After removing the battery from the machine or

charger, be sure to attach the battery cover to

the battery and store it in a dry place.

11. Do not replace the battery with wet hands.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

2. Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product.

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious

personal injury.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper with the battery

cartridge. It may result in a re, excessive heat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re, excessive heat, or explosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask o open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliant products may result in a re, exces-

sive heat, explosion, or leak of electrolyte.

13 ENGLISH

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may cause heating, catching re,

burst and malfunction of the tool or battery car-

tridge, resulting in burns or personal injury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near high-voltage electri-

cal power lines. It may result in a malfunction or

breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

ASSEMBLY

WARNING: Always be sure that the lock key

and battery cartridge are removed before carrying

out any work on the mower. Failure to remove the

lock key and the battery cartridge may result in seri-

ous personal injury from accidental start-up.

WARNING: Never start the mower unless it is

completely assembled. Operation of the machine

in a partially assembled state may result in serious

personal injury from accidental start-up.

Installing the handle

NOTICE: When installing handles, position the

cords so that they are not caught by anything

between the handles. If the cord is damaged, the

mower switch may not work.

1. Align the holes in the lower handle with the holes

in the mower body, and then tighten 4 bolts temporarily.

► Fig.1: 1. Lower handle 2. Bolt

► Fig.2: 1. Holes for upper bolt

NOTE: The handle height can be adjusted in two

levels by replacing the upper bolt in either of the two

holes on each side of the mower body. For details,

refer to the section for adjusting the handle height.

2. Firmly tighten 4 bolts which were temporarily

tightened in step 1 using box wrench 13.

3. Align the hole in the lower handle with the hole in

the upper handle, then insert the bolt from inside, and

then tighten the nut from outside with box wrench 13.

Perform the same procedure on the other side.

► Fig.3: 1. Bolt 2. Lower handle 3. Nut 4. Hole

5. Upper handle

CAUTION: Hold the upper handle rmly so

that it does not drop o your hand. Otherwise, the

handle may fall and cause an injury.

4. Attach the holders to the handle.

Align the protrusions on the holder with the holes on the

handle so that the protrusions t in the holes. Position

the cords as shown in the gure.

► Fig.4: 1. Cord 2. Holder

Removing the mulching plug

1. Open the rear cover.

► Fig.5: 1. Rear cover

2.

Remove the mulching plug while holding down the lever.

► Fig.6: 1. Lever 2. Mulching plug

Assembling the grass basket

1. Pick up the upper clip of the grass basket.

► Fig.7: 1. Upper clip

2. Insert the frame into the grass basket as far as it

will go while holding the handle of the frame.

► Fig.8: 1. Handle

NOTICE: Do not insert the handle into the grass

basket. Be sure to insert the frame along the stitch of

the grass basket.

3. Make sure that there is no sagging on the corners

of the grass basket.

► Fig.9

4. Open the upper clip, and attach it to the frame.

► Fig.10

5.

Attach all the other clips as shown in the gure. Make

sure that all the clips are securely attached to the frame.

► Fig.11: 1. Clip

14 ENGLISH

Installing or removing the grass

basket

To install the grass basket, follow the steps below.

1. Open the rear cover.

► Fig.12: 1. Rear cover

2. Hold the handle of the grass basket, and then

hook the grass basket on the rod of the mower body as

shown in the gure.

► Fig.13: 1. Rod 2. Handle 3. Grass basket

To remove the grass basket, open the rear cover, and

then remove the grass basket by holding the handle.

Attaching the mulching plug

1. Open the rear cover, and then remove the grass

basket.

► Fig.14: 1. Rear cover 2. Grass basket

2. Attach the mulching plug while holding down the

lever, and then release the lever to lock the mulching

plug.

► Fig.15: 1. Lever 2. Mulching plug

FUNCTIONAL

DESCRIPTION

Installing or removing battery

cartridge

CAUTION: Always switch o the machine

before installing or removing of the battery

cartridge.

CAUTION: Hold the machine and the battery

cartridge rmly when installing or removing bat-

tery cartridge. Failure to hold the machine and the

battery cartridge rmly may cause them to slip o

your hands and result in damage to the machine and

battery cartridge and a personal injury.

CAUTION: Make sure that you lock the battery

cover before use. Otherwise, mud, dirt, or water may

cause damage to the product or the battery cartridge.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

it may accidentally fall out of the machine, causing

injury to you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

NOTE: The machine does not work with only one

battery cartridge.

To install the battery cartridge;

1. Pull up the locking lever, and then open the battery

cover.

► Fig.16: 1. Battery cover 2. Locking lever

2. Align the tongue on the battery cartridge with the

slot on the machine, and then slide the cartridge until it

locks in place with a little click.

► Fig.17: (1) Battery port 1 (2) Battery port 2

(3) Battery cartridge

NOTE: Install at least 2 battery cartridges to battery

port 1 or battery port 2.

3. Insert the lock key in the place shown in the gure

as far as it will go.

► Fig.18: 1. Lock key

4. Close the battery cover and push it until it is

latched with the locking lever.

To remove the battery cartridge;

1. Pull up the locking lever and open the battery

cover.

2. Pull out the battery cartridge from the machine

while sliding the button on the front of the cartridge.

3. Pull out the lock key.

4. Close the battery cover.

Switching the battery cartridges

► Fig.19: 1. Battery selection switch

The machine uses 2 battery cartridges for operation

at a time. Up to 4 battery cartridges can be installed to

the machine. Before operating the machine, select the

battery port 1 or battery port 2 by turning the battery

selection switch.

NOTE: If only 2 battery cartridges are installed to the

machine, be sure to select the battery port to which

the battery cartridges are installed using the battery

selection switch.

Machine / battery protection system

The machine is equipped with a machine/battery protec-

tion system. This system automatically cuts o power to

the motor to extend machine and battery life. The machine

will automatically stop during operation if the machine or

battery is placed under one of the following conditions:

Overload protection

When the battery is operated in a manner that causes

it to draw an abnormally high current, the machine

automatically stops and the main power lamp blinks in

green. In this situation, turn the machine o and stop

the application that caused the machine to become

overloaded. Then turn the machine on to restart.

Overheat protection

When the machine or battery is overheated, the

machine stops automatically and the main power lamp

lights up in red. In this case, let the machine and battery

cool before turning the machine on again.

Overdischarge protection

When the battery capacity is not enough, the machine

stops automatically and the main power lamp blinks in

red. In this case, remove the battery from the machine

and charge the battery cartridges or change the battery

cartridges to fully charged ones.

15 ENGLISH

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

► Fig.20: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may dier slightly

from the actual capacity.

NOTE: The rst (far left) indicator lamp will blink when

the battery protection system works.

Control panel

The control panel has the main power switch, the mode

switching button, and the indicator of remaining battery

capacity.

► Fig.21: 1. Battery indicator 2. Mode switching

lamp 3. Main power lamp 4. Check button

5. Mode switching button 6. Main power

switch

Main power switch

WARNING: Always turn o the main power

switch when not in use.

To turn on the machine, press the main power switch.

The main power lamp lights up in green. To turn o the

machine, press the main power switch again.

NOTE: If the main power lamp lights up in red or

blinks in red or green, refer to the instructions for

machine/battery protection system.

NOTE: This machine employs the auto power-o

function. To avoid unintentional start up, the main

power switch will automatically shut down when the

switch lever and drive lever (if equipped) are not

pulled for a certain period after the main power switch

is turned on.

Mode switching button

You can switch the operating mode by pressing the

mode switching button. When the machine is turned on,

the machine starts up in the normal mode. When you

press the mode switching button, the machine shifts to

the noise reduction mode and the mode switching lamp

lights up in green. In the noise reduction mode, you can

decrease the noise at mowing. When you press the

mode switching button again, the machine returns to

the normal mode.

Indicating the remaining battery

capacity

Press the check button to indicate the remaining battery

capacities. The battery indicators correspond to each

battery.

Battery indicator status

Remaining battery

capacity

On O

50% - 100%

20% - 50%

0% - 20%

NOTE: The indicator lamps for remaining battery

capacity is just for a reference. The actual bat-

tery capacity may dier depending on the usage

conditions.

NOTE: Before you press the check button to indicate

the remaining battery capacities, stop the machine.

Switch action

WARNING: Before installing the battery car-

tridge, always check to see that the switch lever

actuates properly and returns to the original posi-

tion when released. Operating the machine with a

switch that does not actuate properly can lead to loss

of control and serious personal injury.

NOTE: The mower does not start without pressing the

switch button even the switch lever is pulled.

NOTE: Mower may not start due to the overload

when you try to mow long or dense grass at a time.

Increase the mowing height in this case.

This mower is equipped with the lock key and handle

switch. If you notice anything unusual with either of the

lock key or switch, stop the operation immediately and

have them checked by your nearest Makita Authorized

Service Center.

16 ENGLISH

1. Install the battery cartridges. Insert the lock key,

and then close the battery cover.

2. Select the battery cartridges used for operation by

turning the battery selection switch.

3. Press the main power switch.

4. Pull the switch lever toward you while holding

down the switch button. Release the switch button as

soon as the motor starts running.

► Fig.22: 1. Switch button 2. Switch lever

NOTE: If the lock key is not inserted, the power lamp

blinks in green when you pull the switch lever.

5. While holding the switch lever, push the drive lever

forward and hold it to drive the rear wheels.

► Fig.23: 1. Drive lever

NOTE:

You can drive the rear wheels by pushing the drive

lever forward and hold it without pulling the switch lever.

6. Release the drive lever and the switch lever to

stop the machine.

Adjusting the mowing height

WARNING:

Never put your hand or leg under

the mower body when adjusting the mowing height.

WARNING: Always make sure that the lever

ts in the groove properly before operation.

The mowing height can be adjusted in the range of

between 20 mm and 100 mm.

Remove the lock key, and then pull the mowing height

adjusting lever outward of the mower body and move it

to your desired mowing height.

► Fig.24: 1. Mowing height adjusting lever

The table below shows the relationship between the number

on the mower body and the approximate mowing height.

Number Mowing height

120 mm

226 mm

332 mm

439 mm

547 mm

655 mm

763 mm

874 mm

986 mm

10 100 mm

Hold the front grip or the lower handle with one hand, and then

move the mowing height adjusting lever with the other hand.

► Fig.25: 1. Mowing height adjusting lever 2. Lower

handle 3. Front grip

NOTE: The mowing height gures should be used

just as a guideline. Depending on the conditions of

the lawn or the ground, the actual lawn height may

become slightly dierent from the set height.

NOTE: Try a test mowing of grass in a less conspicu-

ous place to get your desired height.

Grass level indicator

Grass level indicator shows the volume of mowed

grass. When the grass basket is not full, the indicator

oats while the blades are running.

► Fig.26: 1. Grass level indicator

When the grass basket is almost full, the indicator does

not oat while the blades are running. In this case, stop

the operation immediately and empty the basket.

► Fig.27: 1. Grass level indicator

NOTE: This indicator is a rough guide. Depending on

the conditions of inside of the basket, this indicator

may not work properly.

Adjusting the handle height

CAUTION: Before removing the bolts, hold

the upper handle rmly. Otherwise, the handle may

fall and cause an injury.

The handle height can be adjusted in two levels.

1. Remove the upper bolts of the lower handle using

box wrench 13, and then loosen the lower bolts.

► Fig.28: 1. Upper bolt 2. Lower bolt

2. Adjust the handle height, and then tighten the

upper and lower bolts rmly.

Adjusting the traveling speed

► Fig.29: 1. Speed lever

The traveling speed can be adjusted with the speed

lever. To decrease the speed, pull the lever toward you,

and to increase the speed, turn the lever forward.

Using mulching plug

The mulching plug allows you to return the cut grass to

the ground without gathering the cut grass in the grass

basket. When you operate the machine with the mulch-

ing plug, be sure to remove the grass basket.

NOTICE: When using the machine with the

mulching plug, make sure that the total length of

grass is 30 mm or more, or the cut length is 15

mm or less.

► Fig.30: (1) 30 mm or more (2) 15 mm or less

Using the rear discharge

Using the rear discharge allows you to discharge the cut

grass to the ground from the rear side of the machine

without gathering the cut grass in the grass basket.

When you operate the machine using the rear dis-

charge, be sure to remove the grass basket and mulch-

ing plug, and close the rear cover.

17 ENGLISH

Electronic function

The machine is equipped with the electronic functions

for easy operation.

• Constant speed control of blade rotation

Electronic speed control for obtaining constant

speed. Possible to get ne nish, because the

rotating speed is kept constant even under load

condition.

• Electric brake

This machine is equipped with an electric brake.

If the machine consistently fails to quickly stop

the mower blades after releasing the switch lever,

have the machine serviced at Makita Authorized

Service Center.

OPERATION

Mowing

WARNING: Before mowing, clear away sticks

and stones from mowing area. Furthermore, clear

away any weeds from mowing area in advance.

WARNING: Always wear the safety goggles or

safety glasses with side shields when operating

the mower.

CAUTION: If the cut grass or foreign object

blocks up inside of the mower body, be sure to

remove the lock key and battery cartridge and

wear gloves before removing the grass or foreign

object.

NOTICE: Use this machine for mowing lawn only.

Do not mow weeds with this machine.

► Fig.31

Firmly hold the handle with both hands when mowing.

The mowing speed guideline is approximately 7 to 14

meters per 10 seconds.

► Fig.32

The center lines of the front wheels are guidelines to

mowing width. Using the center lines as guidelines,

mow in strips. Overlap by one half to one third the previ-

ous strip to mow the lawn evenly.

► Fig.33: 1. Mowing width 2. Overlapping area

3. Center line

Change the mowing direction each time to prevent the

grass grain pattern from forming in just one direction.

► Fig.34

Periodically check the grass basket for mowed grass.

Empty the grass before it becomes full. Before every

periodical check, be sure to stop the mower then

remove the lock key and the battery cartridge.

NOTICE: Using the mower with the grass basket

full prevents smooth blade rotation and places

an extra load on the motor, which may cause

breakdown.

Mowing a long-grass lawn

Do not try to cut long grass all at once. Instead, mow

the lawn in steps. Leave a day or two between mowings

until the lawn becomes evenly short.

► Fig.35

NOTE: Mowing long grass to a short length all at

once may cause the grass to die. The cut grass may

also block up inside of the mower body.

Emptying the grass basket

WARNING: To reduce a risk of accident, reg-

ularly check the grass basket for any damage or

weakened strength. Replace the grass basket if

necessary.

1. Release the switch lever and drive lever.

2. Remove the lock key.

3. Open the rear cover and take out the grass basket

by holding the handle.

► Fig.36: 1. Rear cover 2. Handle 3. Grass basket

4. Empty the grass basket.

MAINTENANCE

WARNING: Always be sure that the lock

key and battery cartridge are removed from the

mower before storing or carrying the mower or

attempting to perform inspection or maintenance.

WARNING: Always remove the lock key when

the mower is not in use. Store the lock key in a

safe place out of reach of children.

WARNING: Wear gloves when performing

inspection or maintenance.

WARNING: Always wear the safety goggles or

safety glasses with side shields when performing

inspection or maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs, any other maintenance or adjustment should

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Maintenance

1. Remove the lock key and battery cartridges, and

then close the battery cover.

2. Put the mower on its side and clean grass clip-

pings accumulated on the underside of mower deck.

3. Pour water toward the bottom of the machine to

which the blade is attached.

NOTICE: Do not wash the machine with high

pressure water.

18 ENGLISH

4. Check all nuts, bolts, knobs, screws, fasteners etc.

for tightness.

5. Inspect moving parts for damage, breakage, and

wear. Damaged or missing parts should be repaired or

replaced.

6. Store the mower in a safe place out of the reach of

children.

NOTICE: Do not pour water to the area shown in

the gure. Pouring water to the motor unit may cause

a malfunction of the machine.

► Fig.37: 1. Area where water should not be poured

Carrying the mower

When carrying the mower, hold the front grip and rear

grip with two people as shown in the gure.

► Fig.38: 1. Front grip 2. Rear grip

Storing

Store mower indoors in a cool, dry and locked place.

Don't store the mower and charger in locations where

the temperature may reach or exceed 40 °C.

Removing or installing the mower

blade

WARNING: The blade coasts for a few sec-

onds after releasing the switch. Do not start any

operation until the blade comes to a complete

stop.

WARNING: Always remove the lock key and

battery cartridge when removing or installing the

blade. Failure to remove the lock key and battery

cartridge may cause a serious injury.

WARNING: Always wear gloves when han-

dling the blade.

Removing the mower blade

1. Put the mower on its side so that the mowing

height adjusting lever comes to the upper side.

2. To lock the blade, insert the pin supplied with the

machine into a hole on the mower body.

3. Turn the bolt counterclockwise with box wrench

17.

► Fig.39: 1. Mower blade 2. Pin 3. Box wrench

4. Remove the bolt, and then mower blade.

► Fig.40: 1. Blade support 2. Mower blade 3. Bolt

4. Protrusion

NOTICE: When installing the mower blade, make

sure that the protrusions on the blade support t

in the holes in the mower blade.

Installing the mower blade

WARNING: Install the mower blade carefully.

It has a top/bottom facing.

WARNING: Tighten the bolt clockwise rmly

to secure the blade.

WARNING: Make sure that the mower blade

and all the xing parts are installed correctly and

tightened securely.

WARNING: When you replace the blades,

always follow the instructions provided in this

manual.

NOTICE: After installing the mower blades,

remove the pin from the mower body.

To install the mower blades, perform the removal proce-

dure in reverse.

19 ENGLISH

TROUBLESHOOTING

Before asking for repairs, conduct your own inspection rst. If you nd a problem that is not explained in the manual,

do not attempt to disassemble the machine. Instead, ask Makita Authorized Service Centers, always using Makita

replacement parts for repairs.

State of abnormality Probable cause (malfunction) Remedy

Mower does not start. Two battery cartridges are not installed. Install two charged battery cartridges.

Battery problem (under voltage) Recharge the battery cartridge. If recharging is not

eective, replace battery cartridge.

The lock key is not inserted. Insert the lock key.

Battery selection switch is not in the

correct position.

Select the battery port to which the battery car-

tridges are installed using the battery selection

switch.

Motor stops running after a little use. Battery's charge level is low. Recharge the battery cartridge. If recharging is not

eective, replace battery cartridge.

Cutting height is too low. Increase the cutting height.

Cut grass is clogged in the mower. Remove the clogged grass from the mower.

Motor does not reach maximum

RPM.

Battery cartridge is installed improperly. Install the battery cartridge as described in this

manual.

Battery power is dropping. Recharge the battery cartridge. If recharging is not

eective, replace battery cartridge.

The drive system does not work

correctly.

Ask your local authorized service center for repair.

Mower blade does not rotate:

stop the mower immediately!

Foreign object such as a branch is

jammed near the blade.

Remove the foreign object.

The drive system does not work

correctly.

Ask your local authorized service center for repair.

Abnormal vibration:

stop the mower immediately!

Blade is imbalanced, excessively or

unevenly worn.

Replace the blade.

OPTIONAL

ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita

machine specied in this manual. The use of any

other accessories or attachments might present a risk

of injury to persons. Only use accessory or attach-

ment for its stated purpose.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service

Center.

• Mower blade

• Makita genuine battery and charger

NOTE: Some items in the list may be included in the

product package as standard accessories. They may

dier from country to country.

20 SVENSKA

SVENSKA (Originalinstruktioner)

SPECIFIKATIONER

Modell: DLM537

Klippbredd (knivdiameter) 534 mm

Hastighet utan belastning Normalt läge 2 800 min-1

Bullerdämpningsläge 2 300 min-1

Artikelnummer för byte av

gräsklipparkniv

Rak gräsklipparkniv 191D52-7 / 191W87-2

Mulchblad 191Y65-4

Dimensioner

(L x B x H)

L: 1 655 mm till 1 740 mm

B: 590 mm

H: 990 mm till 1 100 mm

Rullhastighet 2,5 - 5,0 km/h

Märkspänning 36 V likström

Nettovikt

När rak gräsklipparkniv är installerad

42,6 - 46,1 kg

När mulchbladet är installerat 42,6 - 46,1 kg

Skyddsgrad IPX4

•

På grund av vårt pågående program för forskning och utveckling kan dessa specikationer ändras utan föregående meddelande.

• Specikationer kan variera mellan olika länder.

• Vikten kan variera beroende på tillbehören, inklusive batterikassett. Den lättaste och den tyngsta kombinatio-

nen enligt EPTA-procedur 01/2014 visas i tabellen.

Tillgänglig batterikassett och laddare

Batterikassett BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B

Laddare DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /

DC18SH

• Vissa av batterikassetterna och laddarna på listan ovan kanske inte nns tillgängliga i din region.

VARNING: Använd endast batterikassetter och laddare från listan ovan. Användning av andra batterikas-

setter och laddare kan orsaka personskada och/eller brand.

VARNING: Använd inte en strömförsörjning med sladd, som en batteriadapter eller bärbart strömpa-

ket, med denna maskin. Kabeln till sådan anordning kan hindra användningen och leda till personskada.

Symboler

Följande visar symbolerna som kan användas för utrust-

ningen. Se till att du förstår innebörden innan användning.

Var extra försiktig och uppmärksam.

Läs igenom bruksanvisningen.

Fara! Se upp för ygande föremål.

Avståndet mellan maskinen och åskådare

måste vara minst 15 m.

Placera aldrig dina händer eller fötter nära

kniven under gräsklipparen. Knivarna

fortsätter att rotera efter det att motorn

stängts av.

Ta ut säkerhetsnyckeln före kontroll, juste-

ring, rengöring, service, förvaring eller om

gräsklipparen lämnas obevakad.

Risk för elektrisk stöt. Kontakt med vatten

kan orsaka elstöt.

Häll inte på vatten.

Ni-MH

Li-ion

Gäller endast inom EU

P.g.a. förekomsten av farliga komponenter i

utrustningen kan avfall innehållande elektrisk och

elektronisk utrustning, ackumulatorer och batterier

ha negativ inverkan på miljön och människors hälsa.

Kassera inte elektriska och elektroniska appa-

rater eller batterier ihop med hushållsavfall!

I enlighet med EU-direktiven om avfall

som utgörs av eller innehåller elektrisk och

elektronisk utrustning och om batterier och

ackumulatorer och förbrukade batterier

och ackumulatorer, och dess införlivande

i nationell lagstiftning, bör förbrukad elek-

trisk och elektronisk utrustning, batterier

och ackumulatorer förvaras separat och

transporteras till en särskild uppsamlings-

plats för kommunalt avfall, som drivs i

enlighet med regelverket för miljöskydd.

Detta anges av symbolen med den över-

kryssade soptunnan på hjul som sitter på

utrustningen.

Leht laadib ...

Makita DLM537 Kasutusjuhend

Makita DLM537 Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid