Jacobsen 68131G01 Omaniku manuaal
- Kategooria
- Muruniidukid
- Tüüp
- Omaniku manuaal
Safety, Operation, & Maintenance Manual
WARNING
Warning: If incorrectly used, this machine can
cause severe injury. Those who use and maintain
this machine should be trained in its proper use,
warned of its dangers, and must read the entire
manual before attempting to set up, operate, adjust,
or service the machine.
When Performance Matters.
™
GB
AR522
™
68131G01 – AR522-T4I, Kubota
®
V2403-M-DI, 4WD with ROPS
4273092-Rev C
2
This manual contains safety and operating instructions
for your new Jacobsen machine. This manual should be
stored with the equipment for reference during operation.
Before you operate your machine, you and each operator
you employ should read the manual carefully in its
entirety. By following the safety, operating, and
maintenance instructions, you will prolong the life of your
equipment, and maintain its maximum efficiency.
If additional information is needed, contact your
Jacobsen Dealer.
The serial plate is located on the left rear frame rail.
Jacobsen recommends you record these numbers below
for easy reference.
CHARLOTTE, NC
YEAR OF
PRODUCTION:
MADE IN U.S.A.
®
A Textron Company
FOREWORD
© 2018 Textron Specialized Vehicles
This manual may not re reproduced in whole or in part without the express permission of TSV (Augusta) Technical Communications
Department.
8-2018
CALIFORNIA PROPOSITION 65
WARNING
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects and other reproductive harm.
!
CONTENTS
3
CONTENTS
CONTENTS
SAFETY
1.1How to Operate Safely . . . . . . . . . . . . . . . . . . . . 4
1.2 Important Safety Notes . . . . . . . . . . . . . . . . . 7
SPECIFICATIONS
2.1 Product Identification . . . . . . . . . . . . . . . . . . 8
2.2 V2403-M-DI Engine . . . . . . . . . . . . . . . . . . . 8
2.3 Mower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Weights and Dimensions . . . . . . . . . . . . . . . 8
2.5 Cutting Units . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.6 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.7 Support Literature . . . . . . . . . . . . . . . . . . . . . 9
2.8 Declaration of Conformity . . . . . . . . . . . . . . 10
2.9 Vibration Level . . . . . . . . . . . . . . . . . . . . . . 13
DECALS
CONTROLS
4.1 Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.2 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.3 Control Panel . . . . . . . . . . . . . . . . . . . . . . . 21
4.4 Operator Alerts . . . . . . . . . . . . . . . . . . . . . . 22
OPERATION
5.1 Daily Inspection . . . . . . . . . . . . . . . . . . . . . 23
5.2 Interlock System . . . . . . . . . . . . . . . . . . . . . 23
5.3 Operating Procedures . . . . . . . . . . . . . . . . . 24
5.4 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.5 Stopping / Parking . . . . . . . . . . . . . . . . . . . 25
5.6 To Drive / Transport . . . . . . . . . . . . . . . . . . 26
5.7 Mowing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.8 Mowing Speed . . . . . . . . . . . . . . . . . . . . . . 26
5.9 Hillside Operation . . . . . . . . . . . . . . . . . . . . 27
5.10 Towing / Trailering . . . . . . . . . . . . . . . . . . . 29
5.11 Daily Maintenance . . . . . . . . . . . . . . . . . . . 30
MAINTENANCE & LUBRICATION CHARTS
6.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.2 Maintenance Chart . . . . . . . . . . . . . . . . . . . 31
6.3 Lubrication Chart . . . . . . . . . . . . . . . . . . . . 32
MAINTENANCE
7.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.2 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.3 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.4 Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7.5 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7.6 Fuel System . . . . . . . . . . . . . . . . . . . . . . . . 34
7.7 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.8 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . 35
7.9 Charging Battery . . . . . . . . . . . . . . . . . . . . . 35
7.10 Hydraulic Hoses . . . . . . . . . . . . . . . . . . . . . 36
7.11 Hydraulic Oil . . . . . . . . . . . . . . . . . . . . . . . . 36
7.12 Hydraulic Filter . . . . . . . . . . . . . . . . . . . . . . 37
7.13 Electrical System . . . . . . . . . . . . . . . . . . . . 37
7.14 Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.15 Roll Over Protective Structure (ROPS) . . . . 38
7.16 Muffler and Exhaust . . . . . . . . . . . . . . . . . . 38
7.17 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7.18 Wheel Mounting Procedure . . . . . . . . . . . . 39
7.19 Inspecting Blades . . . . . . . . . . . . . . . . . . . . 39
7.20 Sharpening Blades . . . . . . . . . . . . . . . . . . . 40
7.21 Care and Cleaning . . . . . . . . . . . . . . . . . . . 40
7.22 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
ADJUSTMENTS
8.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
8.2 Mow Speed . . . . . . . . . . . . . . . . . . . . . . . . . 42
8.3 Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
8.4 Neutral Adjustment . . . . . . . . . . . . . . . . . . . 43
8.5 Forward / Reverse Speed . . . . . . . . . . . . . . 43
8.6 Steering Toe-In . . . . . . . . . . . . . . . . . . . . . . 44
8.7 Traction Control System Calibration . . . . . . 44
8.8 Cutting Height . . . . . . . . . . . . . . . . . . . . . . . 45
8.9 Torque Specification . . . . . . . . . . . . . . . . . . 46
PROBLEM SOLVING
9.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
9.2 Controller Lamps . . . . . . . . . . . . . . . . . . . . . 48
9.3 Electrical Circuits . . . . . . . . . . . . . . . . . . . . 49
QUALITY OF CUT
10.1 Quality of Cut Troubleshooting . . . . . . . . . . 50
10.2 Washboarding . . . . . . . . . . . . . . . . . . . . . . . 50
10.3 Step Cutting . . . . . . . . . . . . . . . . . . . . . . . . 51
10.4 Scalping . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
10.5 Stragglers . . . . . . . . . . . . . . . . . . . . . . . . . . 53
10.6 Streaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
10.7 Windrowing . . . . . . . . . . . . . . . . . . . . . . . . . 55
10.8 Mismatched Cutting Units . . . . . . . . . . . . . . 56
NOTES
1 SAFETY
4
1 SAFETY
1.1 HOW TO OPERATE SAFELY
SAFE OPERATION
a Read the Operator’s Manual and other training
material. If the operator or technician can not read
this manual, the owner is responsible to describe
this material to the operators and technicians.
Manuals in additional languages may be available
on the Jacobsen or RansomesJacobsen website.
a Read all of the instructions for this mower carefully.
Know the controls and the correct operation of the
equipment.
b Children or persons who do not understand these
instructions must not use the mower. The local
regulations can limit the age of the operator.
c Never use a mower near persons, including
children or animals.
d Remember that the operator or owner is
responsible for accidents or hazards that occur to
other persons or their property.
e Never carry passengers.
f Never allow persons to operate or service the
mower or its attachments without correct
instructions.
g Do not operate equipment while tired, sick or after
you use alcohol or drugs.
PREPARATION
a When you operate the mower, wear correct
clothing, slip resistant work shoes or boots, work
gloves, hard hat, safety glasses and hearing
protection. Long hair, loose clothing or jewelry can
be caught in moving parts.
b Do not operate the equipment with the Interlock
System disconnected or the system does not
operate correctly. Do not disconnect or prevent the
operation of any switch.
c Never operate equipment that is not in correct
order or without decals, guards, shields, deflectors
or other protective devices fastened. DO NOT
operate the cutting unit without the discharge chute
or mulching plate installed.
d Inspect the mower before you operate the mower.
Check the tire pressure, engine oil level, the
radiator coolant level and the air cleaner indicator.
Fuel is flammable. Use caution when you add the
fuel to the mower.
e Operate the mower in daylight or in good artificial
light. Use caution when you operate the mower
during bad weather. Never operate the mower with
lightning in the area.
f Inspect the area to select the accessories and
attachments that are needed to correctly and safely
do the job. Only use parts, accessories and
attachments approved by Jacobsen.
g Be careful of holes in the terrain and other hazards
that are not visible.
h Inspect the area where the equipment is operated.
Remove all objects you can find before you
operate. Be careful of obstructions above the
ground (low tree limbs, electrical wires) and also
underground obstacles (sprinklers, pipes, tree
roots). Enter a new area carefully. Look for possible
hazards.
i Inspect the cutting system before you start the
mower. Make sure the blades are free to rotate.
When you rotate one blade, other blades can
rotate.
OPERATION
a Never operate the engine without enough
ventilation or in an enclosed area. The carbon
monoxide in the exhaust fumes can increase to
dangerous levels.
b Never carry passengers. Keep other persons or
animals away from the mower.
c Disengage all drives and engage the parking brake
before you start the engine. Only start the engine
with the operator in the seat. Never start the engine
with persons near the mower.
d Keep your legs, arms and body inside the operator
compartment while the mower is in operation. Keep
your hands and feet away from the cutting units.
WARNING
EQUIPMENT OPERATED INCORRECTLY OR WITHOUT TRAINING CAN BE DANGEROUS.
Know the location and correct operation of controls. Operators without experience must receive instruction from
another person that knows the correct operation of the equipment before you operate the mower.
Only use parts, accessories and attachments approved by Jacobsen.
!
SAFETY 1
5
e Do not use on the slopes greater than the safe
slope limit for the equipment.
f To guard against over turning or loss of control:
– Operate the mower up and down on the face of
slopes (vertically), but not across the face
(horizontally).
– Do not start or stop suddenly on slopes.
– Decrease the speed when you operate on slopes
or when you must turn. Use caution when you
change direction. Turf condition can change the
mower stability.
– Use caution when you operate the mower near
drop-offs, ditches or embankments.
– Be careful of holes in the terrain and other hazards
that are not visible.
g When you drive in the reverse direction, look
behind you and down to make sure the path is
clear. Do not operate the cutting units when you
drive in the reverse direction.
h Use caution when you go near corners, trees or
other objects that can prevent a clear view.
i Equipment must meet the current regulations to be
driven on the public roads.
j Before you move across or operate on the paths or
roads, turn off the PTO switch, lift the mowers and
travel at decreased speed. Look for traffic.
k Stop the blades when the mower is on any surface
that is not grass.
l Do not release the cut grass in the direction of
persons or allow persons near the mower while in
operation.
m Do not operate the mower with damaged guards or
without safety devices in position.
n Do not change the engine governor setting or over-
speed the engine. Never change or tamper with
adjusters that are closed with a seal for the engine
speed control.
o Before you leave the operator compartment, for
any reason:
– Disengage all the drives and lower attachments to
the ground.
– Engage the parking brake.
– Stop the engine and remove the key.
p When you hit an object or mower starts to cause
the vibration that is not normal, inspect the mower
for damage and make repairs.
q Decrease the throttle setting before you stop the
engine.
r Do not use this equipment for uses that the mower
was not made for.
ROPS
a The ROPS is a safety device. Keep the ROPS in
the vertical and locked position. Always use the
seat belt when you operate the mower. Make sure
the seat belt can be released quickly in an
emergency.
b Only operate the mower with the ROPS in the
folded position on flat and level surfaces when
necessary. Do not operate the mower with the
ROPS in the folded position on slopes, near sharp
edges or near water. There is no roll over
protection with the ROPS in the folded position.
c Check for clearance before you drive below
objects. Do not contact tree branches, electrical
wires or other objects with the ROPS.
d Do not use the seat belt with the ROPS in the
folded position.
e Inspect the ROPS for damage. Keep the ROPS
hardware fastened.
f Do not weld, drill, change or bend the ROPS.
Replace a damaged ROPS. Do not try to correct a
damaged ROPS.
g Do not remove the ROPS from the mower.
h Jacobsen must approve any changes to the ROPS.
SAFE HANDLING OF FUELS
a The fuel and the fuel vapors are flammable. Use
caution when you add the fuel to the mower. The
fuel vapors can cause an explosion.
b Never use the containers that are not approved to
keep or transfer fuel.
c Never keep the mower or fuel containers near an
open flame or any device that can cause the
ignition of fuel or fuel vapors.
d Never fill the fuel containers inside a vehicle or on a
truck or trailer with a plastic liner. Always put the
fuel container on the ground away from your
vehicle before you fill the container.
e Refuel the mower before you start the engine.
When the engine is in operation or while the engine
is hot, never remove the fuel cap or add fuel to the
mower.
f Refuel outdoors only and do not smoke when you
add fuel. Extinguish all types of ignition.
1 SAFETY
6
g The fuel nozzle must touch the rim of the fuel tank
when you add fuel to the mower. Do not use a
device to lock the fuel nozzle in the open position.
h Do not over fill the fuel tank. Leave at least 1 inch
(2.5 cm) below the filler neck.
i Always tighten the fuel tank cap and container cap
after you add fuel.
j If the fuel spills on your clothing, change your
clothing immediately.
MAINTENANCE AND STORAGE
a Before you clean, adjust or repair this equipment,
push PTO switch to the OFF position, lower the
cutting unit to the ground, engage the parking
brake, stop the engine and remove the key.
b Make sure the mower is parked on a solid and level
surface.
c Never work on a mower that is lifted only by the
jack. Always use the jack stands.
d Never allow persons to service the mower or its
attachments without correct instructions.
e When the mower is parked, put into storage or left
without an operator, lower the cutting device unless
a positive mechanical lock is used.
f When you put the mower on a trailer or put the
mower in storage, close the fuel valve. Do not keep
fuel near flames or drain the fuel inside a building.
g Disconnect the battery before you service the
mower. Always disconnect the negative battery
cable before the positive battery cable. Always
connect the positive battery cable before the
negative battery cable.
h Charge the battery in an area with good airflow.
The battery can release hydrogen gas that is
explosive. To prevent an explosion, keep any
device that can cause sparks or flames away from
the battery.
i Disconnect the battery charger from the power
supply before you connect or disconnect the
battery charger to the battery. Wear protective
clothing and use insulated tools when you service
the battery.
j Be careful and wear gloves when you check or
service the cutting unit blades. Replace any
damaged blades, do not try to correct a damaged
blade.
k Keep your hands and feet away from parts that
move. Do not adjust the mower with the engine in
operation, unless the adjustment needs the engine
in operation.
l Carefully release the pressure from components
with stored energy.
m To prevent injury from the hot, high pressure oil,
never use your hands to check for oil leaks. Use
the paper or cardboard to find leaks.
n The hydraulic fluid pressure can have enough force
to enter your skin. If hydraulic fluid has entered
your skin, a doctor must remove the hydraulic fluid
surgically within a few hours or gangrene can
occur.
o When you service the hydraulic system, make sure
the hydraulic fittings, tubes and hoses are
tightened to the correct torque. Make sure the
hydraulic system is in good condition before you
start the engine.
p Keep the mower and the engine clean.
q Allow the engine to become cool before storage
and always remove the ignition key.
r Keep all nuts, bolts and screws tight to make sure
the equipment is in safe condition.
s Replace worn or damaged parts for safety.
Replace damaged or worn decals. Only use parts,
accessories and attachments approved by
Jacobsen.
t To decrease the fire hazard, remove materials that
burn from the engine, muffler, battery tray and fuel
tank area.
u Disconnect the battery and controller connectors
before you weld on this mower.
WHEN YOU PUT THE MOWER ON A
TRAILER
a Be careful when you load or unload the mower on
a trailer. Trailer must be wider than the mower and
can carry the weight of the mower.
b Use a full-width ramp to load or unload the mower
on a trailer.
c Use straps, chains, cables or ropes to fasten the
mower to the trailer. Both front and rear straps
must be sent down and toward sides of trailer.
d Make sure that all latches are correctly fastened.
SAFETY 1
7
1.2 IMPORTANT SAFETY NOTES ________________________________________________
This safety alert symbol is used to alert you to potential hazards.
DANGER - Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
WARNING - Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious
injury.
CAUTION - Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury
and property damage. It may also be used to alert against unsafe practices.
NOTICE - Indicates a potentially hazardous situation which, if not avoided, MAY result in property damage. It may
also be used to alert against unsafe practices.
For pictorial clarity, some illustrations in this manual may show shields, guards, or plates, open or removed. Under no
circumstances should this equipment be operated without these devices securely fastened in place.
By following all instructions in this manual, you will prolong the life of your machine and maintain its maximum
efficiency. Adjustments and maintenance should always be performed by a qualified technician.
If additional information or service is needed, contact your Authorized Jacobsen Dealer who is kept informed of the
latest methods to service this equipment and can provide prompt and efficient service.
WARNING
The Interlock System on this mower prevents the mower from starting unless
the brake lever is engaged, PTO switch is off and traction pedal is in neutral.
The system will stop the engine if the operator leaves the seat without
engaging the parking brake or setting the PTO switch off.
NEVER operate mower unless the Interlock System is working.
!
WARNING
1. Before leaving the operator’s position for any reason:
a. Return traction pedal to Neutral.
b. Disengage all drives.
c. Lower all implements to the ground.
d. Engage parking brake.
e. Stop engine and remove the ignition key.
2. Keep hands, feet, and clothing away from moving parts. Wait for all
movement to stop before you clean, adjust, or service the machine.
3. Keep the area of operation clear of all bystanders and pets.
4. Never carry passengers, unless a seat is provided for them.
5. Never operate mowing equipment without the discharge deflector securely
fastened in place.
!
2 SPECIFICATIONS
8
2 SPECIFICATIONS
2.1 PRODUCT IDENTIFICATION_________________________________________________
68131.............................. AR522-T4I, 5 Gang 4WD with
ROPS
An identification plate, like the one shown, listing the
serial number, is attached to the frame of the mower and
is located on the operator’s right just over the rear axle.
Always provide the serial number of the unit when
ordering replacement parts or requesting service
information.
2.2 V2403-M-DI ENGINE _______________________________________________________
Make ............................... Kubota
Model .............................. V2403-M-DI Diesel, 4 cycle, liquid
cooled
Horsepower .................... 48.9 Hp (36.5 kW) @ 2700 rpm
Note: Actual sustained horsepower will likely be lower
than listed in specifications due to operating limitations
and environmental factors
Bore ................................ 3.43 in. (8.7 cm)
Stroke ............................. 4.03 in. (10.24 cm)
Displacement .................. 148 in
3
(2434 cm
3
)
Torque ............................ 117 ft. lbs. (158 Nm) @ 1600 rpm
Fuel:
Type.......................... No. 2 Diesel, Low or Ultra-Low
Sulfur
Rating ....................... Min. Cetane rating 45
Capacity.................... 17 U.S. gal. (65 liters)
Governor Setting:
High Idle ................... 2920 rpm
Low Idle .................... 1000 rpm
Lubrication:
Capacity.................... 10 U.S. qts.(9.5 liter)
Type.......................... SAE 10W30
API Classification ..... CJ-4
Air Filter .......................... Donaldson, dual element dry type
with evacuator valve and service
indicator.
Alternator ........................ 45 Amp
2.3 MOWER _________________________________________________________________
Tires:
Front ........................ 26.5 x 14 - 12: (6 ply)
Rear ......................... 22.5 x 10 - 8
Tire Pressure:
Front ......................... 16 psi (1.10 BAR)
Rear .......................... 12 psi (0.83 BAR)
Battery:
Type.......................... 12V, 600 Cold Cranking Amps
Group........................ BCI 24
Service Brake ................. Dynamic braking through traction
circuit.
Parking Brake ................. Integrated in wheel motor,
hydraulic release
Speed:
Mow ......................... 0 - 7 mph (0 - 11 kph)
Transport .................. 0 - 12 mph (0 -19.3 kph)
Reverse ................... 0 - 5 mph (0 - 8.1 kph)
Production ...................... 6.4 acres/hr. @ 7 mph
Hydraulic System:
Capacity.......................... 14 U.S. gal. (37.85 liter)
Fluid Type....................... GreensCare 68
Cooling ........................... Oil Cooler
Return Line Filter ............ 10 micron
Steering ......................... Hydrostatic power steering
2.4 WEIGHTS AND DIMENSIONS ________________________________________________
Dimensions: Inches (cm)
Length............................................................130 (330.2)
Height - Top of ROPS .....................................83 (210.8)
Width - Mow.....................................................98 (248.6)
Width - Transport.............................................98 (248.9)
Weight: Lbs. (kg)
Full fluids, decks raised, less operator.
Overall ........................................................ 3691 (1674)
Fuel tank empty, decks raised, less operator.
Overall ........................................................ 3569 (1619)
1451 MARVIN GRIFFIN RD, AUGUSTA, GA, U.S.A.
PRODUCT OF THE U.S.A. WWW.JACOBSEN.COM
®
kg kW
1-800-848-1636 (US)
1674 36.5 XXXX
6813101651
SPECIFICATIONS 2
9
2.5 CUTTING UNITS ___________________________________________________________
Overall cutting Width.......90 in. (254 cm)
Number of cutting units: .. Five - three front, two rear.
Height of Cut................... .3/4 to 5-1/4 in. (1.9 to 13.3 cm) in
1/4 in. (0.6 cm) increments
2.6 ACCESSORIES____________________________________________________________
Refer to the Parts Catalog and contact your Jacobsen
Dealer for a complete listing of accessories and
attachments.
Replacement 2-Post ROPS with Seat Belt ....... 67844
Canopy / Sunshade ........ ................................. 68127
Hood Locking Latch ........ ................................. 1004049
Ball Cage ........................4265201/ 4265202
Standard Blade............... ................................. 4163106
High Lift Blade ................ ................................. 4137186
Low Lift Blade ................. ................................. 4124087
2.7 SUPPORT LITERATURE ____________________________________________________
Contact your Jacobsen Dealer for a complete listing of
literature.
Safety, Operation, & Maintenance Manual ....... 4273092
Parts Manual................... ................................. 4273091
Engine Parts Catalog ...... ................................. 4273093
Service & Repair Manual ................................. TBD
CAUTION
Use of other than Jacobsen authorized parts and accessories may cause personal injury or damage to the
equipment.
!
2 SPECIFICATIONS
10
2.8 DECLARATION OF CONFORMITY ____________________________________________
Jacobsen, A Textron Company
11524 Wilmar Blvd.
Charlotte, NC 28273, USA
68131
AR522 4WD
Lawnmower, Article 12, Item 32
6813101651-6813102500
Kubota V2403-M-E3B Diesel
36.5 kW @ 2700 RPM
228,6 cm
2014/30/EU
2006/42/EC
2000/14/EC, 2005/88/EC
2006/66/EC
2006/42/EC Annex VIII
104 dB(A) ± 0.71 LWA
105 dB(A) LWA
2000/14/EC Annex VI, Part 1
SPECIFICATIONS 2
11
Number: 1088
Sound Research Laboratories Limited
Holbrook House, Little Waldingfield
Sudbury, Suffolk CO10 0TH
90 dB(a) ± 0.71 Leq (2006/42/EC)
BS EN ISO 20643
BS EN ISO 5349-1
BS EN ISO 5349-2
BS EN ISO 5395-3
B71.4
ISO 2631-1
SAE J1194
Jacobsen, A Textron Company
11524 Wilmar Blvd.
Charlotte, NC 28273, USA
April 29, 2016
2 SPECIFICATIONS
12
2006/42/EC Annex II 1.A.2
Christian D. Clifford
Director of Engineering
Ransomes Jacobsen Limited
West Road, Ransomes Europark,
Ipswich, IP3 9TT, England
2006/42/EC Annex II 1.A.10
Adam Blackford
Vice President of Engineering
Jacobsen, A Textron Company
11524 Wilmar Blvd,
Charlotte, NC 28273, USA
4273092 Rev B
GB
United
Kingdom
BE
Belgium
BG
Bulgaria
CH
Switzerland
CN
China
CY
Cyprus
CZ
Czech
Republic
DE
Germany
DK
Denmark
EE
Estonia
ES
Spain
FI
Finland
FR
France
GR
Greece
HU
Hungary
IS
Iceland
IT
Italy
JP
Japan
KR
Korea
LI
Liechenstein
LT
Lithuania
LV
Latvia
MT
Malta
NL
Netherlands
NO
Norway
PL
Poland
PT
Portugal
RO
Romania
RU
Russia
SE
Sweden
SI
Slovenia
SK
Slovakia
TR
Turkey
UA
Ukrain
SPECIFICATIONS 2
13
2.9 VIBRATION LEVEL_________________________________________________________
When the machine was tested for hand/arm vibration levels, the operator was seated in the normal operating position
with both hands on the steering mechanism.
The engine was running and the cutting device was rotating with the
machine stationary.
The Machinery Safety Directive 2006/42/EC
By compliance to:
The Lawnmower Standard BS EN ISO 5395-3
Referenced to Hand/Arm: BS EN ISO 20643:2008
Information Supplied for Physical Agents Directive 2002/44/EC
By reference to:
Hand/Arm Standards: BS EN ISO 5349-1 (2001)
BS EN ISO 5349-2 (2001)
When the machine was tested for Whole Body vibration levels, the operator was seated in the normal operating
position with both hands on the steering mechanism.
The cutting device was rotating with the machine driven in a
straight line at 6 Km/hr on a level freshly cut lawn.
The Machinery Safety Directive 2006/42/EC
By compliance to:
Whole Body EN1032:2003
Information Supplied for Physical Agents Directive 2002/44/EC
By reference to:
Whole Body Standards BS EN ISO 2631-1 (1997)
AR522
Hand/Arm
Acceleration
Level
68131 AR522
Maximum Left Hand or Right Hand Accelerations m/s
2
Mean Value of X, Y, Z Aeq
0.773 ± 1.4
AR522
Whole Body
Acceleration
Level
68131 AR522
Maximum Seat Pad Accelerations m/s
2
Mean Value of X, Y, Z Aeq
0.221 ± 0.168
3 DECALS
14
3 DECALS
Familiarize yourself with the following decals. They are critical to the safe operation of the machine. REPLACE
DAMAGED DECALS IMMEDIATELY.
4164381
4181864
DANGER
Serious injury or death can result from blade
contact or from objects being thrown very long
distances.
• Do not operate machine with discharge chute or
guards flipped up or removed.
• Do not operate machine with bent or damaged
components or with cutting units in the raised
position.
• Keep yourself and others away from the mower
when in operation.
4181861
DANGER
To avoid injury when working with battery:
1. Always connect the black (-) ground last and
remove it first.
2. Keep sparks and flames away, and avoid
contact with acid.
To avoid injury when jumping battery:
1. Connect positive (+) terminal to positive (+)
terminal.
2. Connect negative (-) terminal on good
battery to frame of vehicle that has dead
battery.
IMPORTANT
DO NOT USE STARTING ASSIST FLUIDS
Use of starting assist fluids in the air intake system may be
potentially explosive or cause a “runaway” engine condition. This
could result in serious engine damage.
4181862
WARNING
Radiator is under pressure. Remove
cap slowly to avoid personal injury.
DECALS 3
15
Familiarize yourself with the following decals. They are critical to the safe operation of the machine. REPLACE
DAMAGED DECALS IMMEDIATELY.
5002952
4181865
4181860
• Read operator's manual. Do not allow untrained
operators to use machine.
• Keep shields in place and hardware securely
fastened.
• Keep hands, feet, and clothing away from moving
parts.
• Before you clean, adjust, or repair this equipment,
disengage all drives, engage parking brake, and stop
engine.
• Never carry passengers.
• Keep bystanders away.
• Do not use on slopes greater than 20°.
To prevent injury to you or others, do not
operate this unit with guards removed.
3 DECALS
16
3/4
1
1-1/4
1-1/2
1-3/4
2
2-1/4
2-1/2
2-3/4
3
3-1/4
3-1/2
3-3/4
4
4-1/4
4-1/2
4-3/4
5
5-1/4
CUT
HEIGHT
W/ 1/2
SPACERS
CUT
HEIGHT
W/ 1/4
SPACER
4133609
IMPORTANT
This machine us e s Greens Care 68 ,
a biodeg radable hydraulic fluid.
(Order 5003 103 for 5 g al. pail)
U s e of 10W3 0 is an approved
alternate fluid.
U s e will compromis e all
biodeg radable properties of
Greens Care 68 hydraulic fluid.
4108880
!
WARNING
This structure's
proctective capability
may be impaired by
structural damage,
overturn, or alteration.
If any of these
conditions occur, this
structure must be
replaced.
5003597
4199140
Warning
To prevent burns, do not touch muffler or
muffler shield. Temperatures may exceed
150° F (66° C).
DECALS 3
17
Familiarize yourself with the following decals. They are critical to the safe operation of the machine. REPLACE
DAMAGED DECALS IMMEDIATELY.
3008521
3008682
Tow Valve
Vehicle canNormal
Operation be towed
(Closed) (Open)
Traction Pedal
ReverseForward
4 CONTROLS
18
4 CONTROLS
4.1 ICONS ___________________________________________________________________
WARNING
Never attempt to drive the mower unless you have read the Safety, Operation, &
Maintenance Manual and know how to operate all controls correctly.
Familiarize yourself with the icons shown above and what they represent. Learn the
location and purpose of all the controls and gauges before operating this mower.
Read Manual
High Low
Engine Throttle
PTO
Lock Unlock
Forward Reverse
Travel
Cruise Control
Off Run
Engine
Start
Parking Brake
ON
OFF
Coolant
Temperature
Fuel
Mowers
Lower Raise
Work Lights
Hour Meter
Oil Level Switch
On Off/Test
Engine Oil
Pressure
Glow
Plug
Hydraulic
Oil Filter
Battery
Charge
Warning Lights
Hydraulic
Oil Level
D
!
CONTROLS 4
19
4.2 CONTROLS_______________________________________________________________
A
E
M
U
F
J
S
V
C
B
G
K
L
R
D
H
P
N
T
W
P
E
F
A Tilt Steering Lever
B Mow Speed Stop
C Traction Pedal - Forward
D Traction Pedal - Reverse
E
Seat Adjustment
F Hydraulic Oil Cap/Dipstick
G Air Cleaner Indicator
H Fuel Cap
J Alarm
K Controller / Fuses
L Horn Switch
M Glow Plug Light
N Mower Lift Lever
P PTO Switch
R Light Switch
S Traction Control Switch
T Engine Throttle
U Ignition Switch
V Combination Gauge
W Brake Switch
4 CONTROLS
20
A. Tilt Steering Lever
Pull lever up to release steering column. Tilt
column up or down to position desired.
Release lever to lock steering column in
place.
B. Mow Speed Stop
Limits forward speed while mowing. To operate at
lower travel speed while mowing, rotate lever so it
contacts stop screw (B
1
) on floor board when forward
travel pedal is pressed. To travel at full speed, set
lever in position shown (B
3
). Stop screw (B
2
) can be
adjusted to set specific mow speeds. See Section
8.2.
C. Traction Pedal - Forward
Press front of pedal down for forward travel. Release
pedal to slow mower and stop.
D. Traction Pedal - Reverse
Press rear of pedal down for reverse travel. Release
pedal to slow mower and stop. Allow mower to come
to a complete stop before reversing directions.
Figure 4A
E. Seat Adjustment
Pull left side lever out to adjust seat forward or
backward. To adjust spring tension under seat turn
adjusting knob on front of seat.
F. Hydraulic Oil Cap / Dipstick
Fill to mark on dipstick using clean hydraulic fluid
while machine is cool. Do not overfill.
G. Air Cleaner Indicator
Indicates condition of air cleaner on engine. Clean or
replace air filter when red band appears in clear
window of indicator. See Section 7.4.
H. Fuel Cap
Fill fuel tank with No. 2 diesel fuel, minimum Cetane
Rating of 45. See Section 5.11.
J. Alarm
The alarm, along with the warning lights on the
combination gauge (V), sounds to alert the operator
to conditions requiring immediate attention. See
Section 4.4.
K. Controller / Fuses
The controller is located under the rear hood directly
behind the operator’s seat. It is equipped with lights
to aid in monitoring and problem solving the electrical
system of the mower.
Two spade type fuses are located on the controller.
To replace fuses remove the access panel.
CAUTION
Never adjust steering while mower is moving. Stop
unit and set parking brake before adjusting.
!
B
3
Transport Speed
Mow Speed
B
1
B
2
C
D
CAUTION
Service to the electrical system must be performed by
a trained technician. Before replacing fuses turn
mower off and remove key from ignition.
!
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
Jacobsen 68131G01 Omaniku manuaal
- Kategooria
- Muruniidukid
- Tüüp
- Omaniku manuaal
teistes keeltes
- English: Jacobsen 68131G01 Owner's manual
Seotud paberid
Muud dokumendid
-
Simplicity MULTI-LANGUAGE OPERATOR'S MANUAL, YARD KING RIDING MOWER 17.5/22HP 46" Kasutusjuhend
-
Dolmar PM-5100 S3 Omaniku manuaal
-
-
Husqvarna LC 137i Kasutusjuhend
-
Husqvarna Aspire LC34-P4A Battery Lawn Mower Kasutusjuhend
-
Wolf Garten Benzin-Rasenmäher Kasutusjuhend
-
-
EGO LM2000E Omaniku manuaal
-
-
Ryobi OBC1820B Original Instructions Manual