Zanussi FJE1205 Kasutusjuhend

Kaubamärk: Zanussi

Mudel: FJE1205

Kategooria: Pesumasinad

Tüüp: Kasutusjuhend

WASHING MACHINE

TVÄTTMASKIN

PYYKINPESUKONE

STIRALWNAÅ MAﬁINA

FJE 1205

INSTRUCTION BOOKLET

BRUKSANVISNING

KÄYTTÖOHJE

RUKOVODSTVO PO ÈKSPLUATACII

132988120

RUS

FIN

Copertina 132998120 7-06-2004 17:58 Pagina 1

Washing hints 12

Sorting the laundry 12

Temperatures 12

Before loading the laundry 12

Maximum loads 12

Laundry weights 12

Removing stains 12

Detergents and additives 13

International wash code symbols 14

Operating sequence 15-17

Washing programmes 18

Maintenance 19

Door seal 19

Bodywork 19

Detergent dispenser drawer 19

Drain pump 19

Water inlet filter 20

Emergency emptying out 20

Frost precautions 20

Something not working? 21-22

Warnings 3-4

Disposal 4

Tips for environmental protection 4

Technical specifications 4

Installation 5

Unpacking 5

Positioning 5

Water inlet 5

Water drainage 6

Electrical connection 6

Your new washing machine 7

Description of the appliance 7

Detergent dispenser drawer 7

Use 8

Control panel 8

Controls 8-11

Dear customer,

Please read these operating instructions carefully

and pay particular attention to the safety notes

indicated in the first pages. We recommend that you

keep this instruction booklet for future reference and

pass it on to any future owners.

Transport damages

When unpacking the appliance, check that it is not

damaged. If in doubt, do not use it and contact the

Service Centre.

The symbols you will see on some paragraphs of this booklet have the following meaning:

The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly

important for your safety or correct functioning of the appliance.

The information marked with this symbol provides additional instructions and practical tips on the use of

the appliance.

Tips and information about economical and ecological use of the machine are marked with this symbol.

Our contribution to the protection of the

environment: we use environmentally

friendly paper.

Contents

132988120gb.qxd 08/06/2004 08.49 Pagina 2

ENGLISH

Installation

• All internal packing must be removed before using

the appliance. Serious damage may be caused to

the machine or adjacent furniture if the protective

transit devices are not removed or are not

completely removed. Refer to the relevant

paragraph in the instruction book.

• Any electrical work required to install this appliance

must be carried out by a qualified electrician.

• Any plumbing work required to install this appliance

must be carried out by a qualified plumber.

• After having installed the machine, check that it is

not standing on its electrical supply cable.

• If the appliance is placed on a carpeted floor,

ensure that air can circulate freely between the feet

and the floor.

Use

• This appliance is designed for domestic use. It

must not be used for purposes other than those for

which it was designed.

• Only wash fabrics which are designed to be

machine washed. Follow the instructions on each

garment label.

• Do not overload the appliance. Follow the

instructions in the instruction book.

• Make sure that all pockets are empty. Objects such

as coins, safety pins, pins and screws can cause

extensive damage.

• Do not machine wash garments saturated with

petroleum, methylated spirits, trichlorethylene, etc.

If such fluids have been used to remove stains

prior to washing, wait until they have completely

evaporated from the fabric before placing garments

in the appliance.

• Place small items such as socks, belts, etc. in a

cloth bag or pillowcase to prevent them getting

trapped between the drum and the tub.

• Use only the recommended quantities of fabric

softener. An excessive amount could damage the

laundry.

• Leave the porthole door slightly ajar when the

appliance is not in use. This preserves the door

seal and prevents the formation of musty smells.

• Always check that water has emptied out before

opening the door. If not, drain the water following

the instructions in the instruction book.

• Always unplug the appliance and shut the water

tap after use.

General safety

• Repairs to the machine must be carried out only by

qualified personnel. Repairs carried out by

inexperienced persons could cause serious

danger. Contact your local Service Centre.

• Never pull the power supply cable to remove the

plug from the socket; always take hold of the plug

itself.

• During high temperature wash programmes the

door glass may get hot. Do not touch it!

Child safety

• Children are often not aware of how dangerous

electrical appliances can be. When the machine is

working, children should be carefully supervised

and not be allowed to play with the appliance.

• The packaging components (e.g. plastic film,

polystyrene) can be dangerous to children - danger

of suffocation! Keep them out of children’s reach.

• Keep all detergents in a safe place out of children’s

reach.

• Make sure that children or pets do not climb into the

drum. To avoid this the machine incorporates a

special feature. To activate this device, rotate the

button (without pressing it) inside the door clockwise

until the groove is horizontal. If necessary use a coin.

To disable this device and restore the possibility of

closing the door, rotate the button anti-clockwise until

the groove is vertical.

• When the appliance is to be scrapped, cut off the

electrical supply cable and destroy the plug with

the remaining cable. Disable the door catch in

order to prevent children from becoming trapped

inside while playing.

P1131

Warnings

The following warnings are provided in the interests of overall safety. You must read them carefully before

installing or using the appliance.

132988120gb.qxd 08/06/2004 08.49 Pagina 3

Disposal

Tips for environmental protection

Packaging materials

The materials marked with the symbol are

recyclable.

>PE<=polyethylene

>PS<=polystyrene

>PP<=polypropylene

This means that they can be recycled by disposing of

them properly in appropriate collection containers.

Machine

Use authorised disposal sites for your old appliance.

Help to keep your country tidy!

To save water, energy and to help protect the

environment, we recommend that you follow these

tips:

• Normally soiled laundry may be washed without

prewashing in order to save detergent, water and

time (the environment is protected too!).

• The machine works more economically if it is fully

loaded.

• With adequate pre-treatment, stains and limited

soiling can be removed; the laundry can then be

washed at a lower temperature.

• Measure out detergent according to the water

hardness, the degree of soiling and the quantity of

laundry being washed.

DIMENSIONS Height 85 cm

Width 60 cm

Depth 59 cm

MAXIMUM LOAD Cotton 5 kg

Synthetics 2.5 kg

Delicates 2.5 kg

Woollens/Hand wash 2 kg

SPIN SPEED 1200 rpm max.

POWER SUPPLY VOLTAGE/FREQUENCY 220-230 V/50 Hz

TOTAL POWER ABSORBED 2200 W

MINIMUM FUSE PROTECTION 10 A

WATER PRESSURE Minimum 500 kPa

Maximum 800 kPa

This appliance complies with the following EEC Directives:

73/23/EEC of 19/02/73 relating to low voltage

89/336/EEC of 03/05/89 relating to electromagnetic compatibility.

Technical specifications

132988120gb.qxd 08/06/2004 08.49 Pagina 4

ENGLISH

Installation

Unpacking

All transit bolts and packing must be

removed

before using the appliance.

You are advised to keep all transit devices so that

they can be refitted if the machine ever has to be

transported again.

Using a spanner unscrew and remove the two rear

bottom screws. Slide out the two plastic pins.

Lay the machine gently on its back, making sure

that the hoses are not squashed.

Remove the polystyrene block from the bottom of

the machine and release the two plastic bags.

Very carefully slide out the left polythene bag,

removing it towards the right and then downwards.

Repeat the operation for the right polythene bag,

removing it towards the left and then upwards.

P1127

P1126

P1124

P0001

P1129

Remove the polystyrene base.

Set the machine upright and unscrew the remaining

rear screw. Slide out the relevant pin.

Fill all the holes with the plastic plugs supplied with

the instruction booklet.

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine is

not impeded by carpets, rugs etc. Check that the

machine does not touch the wall or other kitchen

units.

Carefully level by screwing the adjustable feet in or

out. Never place cardboard, wood or similar

materials under the machine to compensate for any

unevenness in the floor.

Water inlet

Connect the water inlet hose to a tap with a 3/4"

thread.

Do not use already employed hoses for water

connections.

The other end of the inlet hose which connects to

the machine can be turned in any direction. Simply

loosen the fitting, rotate the hose and retighten the

fitting, making sure there are no water leaks

P0021

P1088

P1051

P0002

P1128

132988120gb.qxd 08/06/2004 08.49 Pagina 5

The inlet hose must not be lengthened. If it is too

short and you do not wish to move the tap, you will

have to purchase a new, longer hose specially

designed for this type of use.

Water drainage

The end of the drain hose can be positioned in three

ways:

Hooked over the edge of a sink using the plastic

hose guide supplied with the machine. In this

case, make sure the end cannot come unhooked

when the machine is emptying.

This could be done by tying it to the tap with a piece

of string or attaching it to the wall.

In a sink drain pipe branch. This branch must be

above the trap so that the bend is at least 60 cm

above the ground.

Directly into a drain pipe at a height of not less

than 60 cm and not more than 90 cm.

The end of the drain hose must always be

ventilated, i.e. the inside diameter of the drain pipe

must be larger than the outside diameter of the drain

hose.

The drain hose must not be kinked. Run it along the

floor; only the part near the drainage point must be

raised.

P0023

P0022

Electrical connection

This machine is designed to operate on a 220-230

V, single-phase, 50 Hz supply.

Check that your domestic electrical installation can

take the maximum load required (2.2 kW), also

taking into account any other appliances in use.

Connect the machine to an earthed socket.

The manufacturer declines any responsibility

for damage or injury through failure to comply

with the above safety precaution.

Should the appliance power supply cable

need to be replaced, this operation must be

carried out by our Service Centre.

The power supply cable must be easily

accessible after installing the machine.

132988120gb.qxd 08/06/2004 08.49 Pagina 6

ENGLISH

Your new washing machine

1 Detergent dispenser drawer

2 Control panel

3 Door handle

4 Drain pump

5 Adjustable feet

Detergent dispenser drawer

Prewash

Main wash

Fabric softener, starch

Description of the appliance

ECOVAL VE 1200

120

900

700

60°C

40°C

5°C

°C

C0063

This new machine meets all modern requirements for effective treatment of laundry with low water, energy and

detergent consumption.

• The automatic cooling of the washing water from 95° to 60°C before draining will prevent old drain pipes

from being deformed.

• The special wool programme with its new delicate wash system treats your woolens with extreme care.

• The unbalance detection device prevents vibration during spinning.

• The programme selector dial combines the function of programme and temperature selection, making it

easier to set the programme.

132988120gb.qxd 08/06/2004 08.49 Pagina 7

Use

Control panel

Position corresponds to cold wash.

Important!

By depressing TEMPERATURE and SPIN

SPEED buttons simultaneously, the acoustic

signal is switched off in the following cases:

• when depressing the buttons

• when an incorrect option selection is made

• at the end of the programme.

5 SPIN SPEED button

Press this button repeatedly to change the spin

speed, if you want your laundry to be spun at a

speed different from the one proposed by the

washing machine. The relevant light will light up.

Maximum speeds are:

• for cotton: 1200 rpm;

• for synthetic fabrics, wool, and fabrics to be hand-

washed: 900 rpm;

• for delicate fabrics: 700 rpm.

RINSE HOLD position : when you choose this

option, the machine will not drain the water of the

last rinse, so as not to wrinkle the laundry.

At the end of the cycle, the light of the

START/PAUSE button goes out and the door is

locked, the pilot light remains lit, to indicate that

the water must be drained.

To complete the cycle, choose one of the following

options:

• Drain

Press SKIP/RESET button once, all the leds are off, the

display will show three blinking dashes, then press

button in order to select the desired programme. If you

wish to drain or spin press the SKIP/RESET

button until the led of the desired function goes on. You

1 ON/OFF button

Press this button to switch the washing machine on.

Press the ON/OFF button again to switch the

machine off.

2 MAINS-ON light

This light is connected to the ON/OFF button. It

lights up when you press the button, and goes out

when you press it again.

3 FABRIC button

Press this button repeatedly to select the

programme on the basis of the type of laundry to be

washed. The light relevant to the selected

programme will light up. The washing machine will

propose a temperature and automatically select the

maximum spin value provided for the programme

you have chosen. You can change these values by

operating buttons 4 and 5.

Hand wash

When you select this programme, you obtain a

particularly delicate washing, suitable for articles of

clothing whose label indicates that they must be

hand-washed .

4 TEMPERATURE button

Press this button repeatedly to increase or decrease

the temperature, if you want your laundry to be

washed at a temperature different from the one

proposed by the washing machine. The relevant

light will light up.

Maximum temperatures are 95°C for cotton, 60°C

for synthetic fabrics, 40°C for delicate fabrics, wool and

fabrics to be hand-washed (HAND WASH

programme).

12 3 4 5 6 7 8 9101112

1200

900

700

500

60°C

40°C

95°C

30°C

FJE 1205

132988120gb.qxd 08/06/2004 08.49 Pagina 8

ENGLISH

can change the spin speed by means of button and

then depress Start/Pause .

Important! If you accidentally press the

SKIP/RESET button more than once, the display will

show three blinking dashes. To drain the water,

select any washing programme by means of the

FABRIC button, then press SKIP/RESET three

times in order to select the DRAIN position (only the

DRAIN light will remain lit).

6-7 OPTIONS button

Press these buttons to select the following options:

• PREWASH : select this option if you wish your

laundry to be prewashed before the main wash

(not available for wool and hand-wash cycle).

The prewash ends with a short spin at 650 rpm in

programmes for cotton and synthetic fabrics,

whereas in the programme for delicate fabrics the

water is only drained.

• NIGHT CYCLE : when you choose this option, the

machine will not drain the water of the last rinse, so

as not to wrinkle the laundry. As all spinning phases

are suppressed, this washing cycle is very noiseless

and it can be selectionned at night or in times with a

more economical power rate. On cotton and

synthetic programmes the rinses will be performed

with more water.

At the end of the cycle, the light of the

START/PAUSE button goes out and the door is

locked, the pilot light remains lit, to indicate

that the water must be drained.

To complete the cycle, choose one of the following

programmes:

- Drain

Press SKIP/RESET button once, all the leds are off,

the display will show three blinking dashes, then press

button in order to select the desired programme. If

you wish to drain or spin press the

SKIP/RESET button until the led of the desired function

goes on. You can change the spin speed by means of

button and then depress Start/Pause .

Important! If you accidentally press the

SKIP/RESET button more than once, the display

will show three blinking dashes. To drain the

water, select any washing programme by means of

the FABRIC button, then press SKIP/RESET

three times in order to select the DRAIN position

(only the DRAIN light will remain lit).

• QUICK WASH : for laundry that is only slightly

soiled (not for wool and hand wash

programmes).

The washing time will be reduced according to the

type of fabric and the selected temperature.

The PREWASH, NIGHT CYCLE and QUICK WASH

options cannot be selected together.

• SUPER RINSE

this option can be selected

with all programmes except the wool and

hand wash programmes. The machine will

add 2 rinses for cottons and 1 rinse for synthetics

and delicates. This option is recommended for

people who are allergic to detergents, and in areas

where the water is very soft.

• ECONOMY : this option can be selected for

cottons and synthetics lightly or normally soiled

with a temperature of 40°C or higher.

Furthermore the washing temperature will be

reduced automatically and the washing time will be

prolonged.

The SUPER RINSE and the ECONOMY options

cannot be selected together by means of the relevant

button.

8 Display

The following pieces of information are shown on the

display:

• Three blinking dashes, when a programme is

cancelled by means of the SKIP/RESET button.

The three blinking dashes will also appear when you

press the ON/OFF button to switch the machine on,

if the previously selected cycle has been erased.

•

Duration of washing programme in hours

and minutes, after you have selected a

programme.

2.05

132988120gb.qxd 08/06/2004 08.49 Pagina 9

While the programme is running (after you have

pressed the START/PAUSE button), the displayed

time value decreases by one unit every minute.

• The washing machine has stopped with water in

the tub, at the end of a programme with the

RINSE HOLD or NIGHT CYCLE option:

this is indicated by a flashing zero.

• The washing machine has completed the

programme: this is indicated by a blinking zero.

The zero will reappear when you switch the

washing machine on, unless the previous

programme has been erased by means of the

SKIP/RESET button.

Important!

The first time you use the washing machine,

when you switch it on, it may display a blinking zero and

give an audible warning signal. This is due to the fact

that the washing machine has performed a washing

cycle during the manufacturer’s inspection tests, and

this cycle has not been erased after its completion.

• Delay start, a time value indicated in hours and

selected by means of the relevant button.

The delay time is displayed for 3 seconds, then the

duration of the selected programme reappears.

After you have pressed the START/PAUSE button,

the countdown begins, and the delay time value

decreases by one unit every hour.

You can delay the start of the selected programme

by up to 23 hours in one hour intervals.

• An incorrect option selection has been made: this

is indicated by the message Err when a function

incompatible with the current programme is selected.

The incorrect selection is also indicated by an

audible warning signal.

• An alarm code indicates a fault in the machine

operation (see the relevant chapter on page 21).

9 START/PAUSE button

This button has two functions:

• Start: after you have selected the desired

programme and options, press this button to start

the washing machine. The light above the button

will stop flashing and remain lit.

If you have selected a delay time by means of

button 11, the countdown will begin and will be

shown on the display.

• Pause: when you press this button again, the

programme in progress is interrupted. The light

above the button will start flashing. To restart the

programme, press the button again.

When you PAUSE the cycle and it becomes

possible to open the door, provided

• the washing machine is not in the heating phase;

• the level of the water is not high;

• the drum is not turning.

Important! You must set the washing machine to

PAUSE before you make any change in the

programme in progress.

10 SKIP/RESET button

At the end of a programme, you must press this

button once or repeatedly, in order to clear the

contents of the memory (the display will show three

blinking dashes); otherwise, the next time you switch

the washing machine on, the blinking zero will

reappear and the audible warning signals relevant to

the end of the previous cycle will be given.

132988120gb.qxd 08/06/2004 08.49 Pagina 10

ENGLISH

You can also press the RESET button to exclude

one or several phases of the programme which is

running, as indicated below.

- set the washing machine to PAUSE by pressing the

START/PAUSE button (the relevant light will flash);

- press the RESET button once or several times, until

the required phase(s) is(are) cancelled (the light next

to the symbol of the phase(s) will go out).

Example:

In this case, the spin (at

the speed provided for

the selected type of

fabric) will be

performed.

This button allows you also to select special

programmes, such as RINSES, SPIN and DRAIN.

• If the machine is already switched on because it

has just performed a washing programme, proceed

as follows:

- depress RESET once or repeatidly to cancel the

previously performed programme (three blinking

dashes will appear on the display);

- select the type of fabric by means of the relevant

button;

- select the special programme:

• RINSES

Depress RESET once, the pilot light WASH

goes out.

• SPIN

Depress RESET twice, the pilot lights WASH

and RINSES go out.

• DRAIN

Depress RESET three times, the pilot lights

WASH , RINSES and SPIN go out.

Example:

In this case the

machine will perform

the rinses and spin.

• If the machine is switched off:

- depress ON/OFF button to switch it on;

- select the type of fabric by means of button ;

select the special programme as previously

described.

11 DELAY button

This button makes it possible to delay the starting of

the programme from 30 min-60 min-90 min, 2 hours

and then by 1 hour up to maximum of 23 hours. The

delay you have selected is shown on the display for

about 3 seconds; afterwards, the duration of the

programme reappears.

You must select this option after you have set the

programme and before you press the

START/PAUSE button.

The time value shown on the display will decrease

by one unit every hour.

You can change the delay time at any moment,

before you press the START/PAUSE button.

If you have already pressed the START/PAUSE

button, and you wish to cancel the delay time,

proceed as follows:

• set the washing machine to PAUSE by pressing the

START/PAUSE button;

• press the DELAY button twice, to erase the delay

time. The display will indicate “

OO’’

”

• press the START/PAUSE button again.

Important!

The door will be locked throughout the delay time.

If you need to open the door, you must first set the

washing machine to PAUSE by pressing the

START/PAUSE button. After you have closed the

door, press the START/PAUSE button again.

12 Programme phase indicator

lights

When you select a programme, the lights relevant to

the phases that form the programme light up.

After you have started the programme, only the light

relevant to the phase that is currently being carried

out will remain lit.

132988120gb.qxd 08/06/2004 08.49 Pagina 11

Washing hints

Sorting the laundry

Follow the wash code symbols on each garment

label and the manufacturer’s washing instructions.

Sort the laundry as follows:

whites, coloureds, synthetics, delicates, woollens.

Temperatures

95°

for normally soiled white cottons and linen

(e.g. tea cloths, towels, tablecloths,

sheets...)

60° for normally soiled, colour fast garments

(e.g. shirts, night dresses, pyjamas....) in

linen, cotton or synthetic fibres and for

lightly soiled white cotton (e.g. underwear).

(cold)for delicate items (e.g. net curtains), mixed

30°-40° laundry including synthetic fibres and

woollens.

Before loading the laundry

Never wash whites and coloureds together. Whites

may lose their “whiteness” in the wash.

New coloured items may run in the first wash; they

should therefore be washed separately the first time.

Make sure that no metal objects are left in the

laundry (e.g. hair clips, safety pins, pins).

Button up pillowcases, close zip fasteners, hooks

and poppers. Tie any belts or long tapes.

Remove persistent stains before washing. Rub

particularly soiled areas with a special detergent or

detergent paste.

Treat curtains with special care. Remove hooks or tie

them up in a bag or net.

Maximum loads

Recommended loads are indicated in the

programme charts.

General rules:

Cotton, linen: drum full but not too tightly packed;

Synthetics: drum no more than half full;

Delicate fabrics and woollens: drum no more than

one third full.

Washing a maximum load makes the most efficient

use of water and energy.

For heavily soiled laundry, reduce the load size.

Laundry weights

The following weights are indicative:

bathrobe 1200 g

napkin 100 g

quilt cover 700 g

sheet 500 g

pillow case 200 g

tablecloth 250 g

towelling towel 200 g

tea cloth 100 g

night dress 200 g

ladies’ briefs 100 g

man’s work shirt 600 g

man’s shirt 200 g

man’s pyjamas 500 g

blouse 100 g

men’s underpants 100 g

Removing stains

Stubborn stains may not be removed by just water

and detergent. It is therefore advisable to treat them

prior to washing.

Blood: treat fresh stains with cold water. For dried

stains, soak overnight in water with a special

detergent then rub in the soap and water.

Oil based paint: moisten with benzine stain

remover, lay the garment on a soft cloth and dab the

stain; treat several times.

Dried grease stains: moisten with turpentine, lay

the garment on a soft surface and dab the stain with

the fingertips and a cotton cloth.

Rust: oxalic acid dissolved in hot water or a rust

removing product used cold. Be careful with rust

stains which are not recent since the cellulose

structure will already have been damaged and the

fabric tends to hole.

Mould stains: treat with bleach, rinse well (whites

and fast coloureds only).

Grass: soap lightly and treat with bleach (whites and

fast coloureds only).

Ball point pen and glue: moisten with acetone (*),

lay the garment on a soft cloth and dab the stain.

Lipstick: moisten with acetone as above, then treat

stains with methylated spirits. Remove any residual

marks from white fabrics with bleach.

Red wine: soak in water and detergent, rinse and

treat with acetic or citric acid, then rinse. Treat any

residual marks with bleach.

132988120gb.qxd 08/06/2004 08.49 Pagina 12

ENGLISH

Quantity of detergent to be used

The type and quantity of detergent will depend on

the type of fabric, load size, degree of soiling and

hardness of the water used.

Water hardness is classified in so-called “degrees” of

hardness. Information on hardness of the water in

your area can be obtained from the relevant water

supply company, or from your local authority.

Follow the product manufacturers’ instructions on

quantities to use.

Use less detergent if:

– you are washing a small load,

– the laundry is lightly soiled,

– large amounts of foam form during washing.

Ink: depending on the type of ink, moisten the fabric

first with acetone (*), then with acetic acid; treat any

residual marks on white fabrics with bleach and then

rinse thoroughly.

Tar stains: first treat with stain remover, methylated

spirits or benzine, then rub with detergent paste.

(*) do not use acetone on artificial silk.

Detergents and additives

Good washing results also depend on the choice of

detergent and use of the correct quantities to avoid

waste and protect the environment. Although

biodegradable, detergents contain substances

which, in large quantities, can upset the delicate

balance of nature.

The choice of detergent will depend on the type of

fabric (delicates, woollens, cottons, etc.), the colour,

washing temperature and degree of soiling.

All commonly available washing machine detergents

may be used in this appliance:

– powder detergents for all types of fabric,

– powder detergents for delicate fabrics (60°C max)

and woollens,

– liquid detergents, preferably for low temperature

wash programmes (60°C max) for all types of

fabric, or special for woollens only.

The detergent and any additives must be placed in

the appropriate compartments of the dispenser

drawer before starting the wash programme.

If using concentrated powder or liquid detergents, a

programme without prewash must be selected.

The washing machine incorporates a recirculation

system which allows an optimal use of the

concentrated detergent.

Pour liquid detergent into the dispenser drawer

compartment marked just before starting the

programme.

Any fabric softener or starching additives must be

poured into the compartment marked before

starting the wash programme.

Follow the product manufacturer’s recommendations

on quantities to use and do not exceed the «MAX»

mark in the detergent dispenser drawer.

132988120gb.qxd 08/06/2004 08.49 Pagina 13

International wash code symbols

These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.

Energetic wash

Delicate wash

Max. wash

temperature

95°C

Max. wash

temperature

60°C

Max. wash

temperature

40°C

Max. wash

temperature

30°C

Hand wash Do not

wash

at all

Bleaching Bleach in cold water Do not bleach

Ironing Hot iron

max 200°C

Warm iron

max 150°C

Lukewarm iron

max 110°C

Do not iron

Dry cleaning Dry cleaning

in all solvents

Dry cleaning in

perchlorethylene,

petrol, pure alcohol,

R 111 & R 113

Dry cleaning

in petrol,

pure alcohol

and R 113

Do not

dry clean

Drying Flat On the line On clothes

hanger

Tumble dry

high

temperature

low

temperature

Do not

tumble dry

132988120gb.qxd 08/06/2004 08.49 Pagina 14

ENGLISH

4. Switch the machine on

Press the ON/OFF button to switch the machine

on. The display will show three blinking dashes or a

blinking zero. The light above the button will light up.

5. Select the desired programme/fabric

Press the FABRIC button repeatedly, in order to

select the desired programme/fabric. The relevant

light will light up.

The lights relevant to the phases that form the

programme will light up.

The display will show the duration of the selected

programme, calculated on the basis of the maximum

load for each type of fabric. The START/PAUSE

button light will start flashing.

If the load of laundry to be washed is small, at the

beginning of the cycle the display will still indicate the

duration relevant to the maximum load. The duration

value will be gradually adjusted during the execution

of the cycle.

6. Select the temperature

Press the TEMPERATURE button if you wish to

select a temperature value different from the one

proposed by the washing machine.

The relevant light will light up.

------

Operating sequence

Before washing your first load of laundry, we

recommend that you run a cotton cycle at 60°C,

with the machine empty, in order to remove any

manufacturing residue from the drum and tub.

Pour half a measure of detergent into the main wash

compartment and start up the machine.

1. Place the laundry in the drum

Open the door.

Place the laundry in the drum, one item at a time,

shaking them out as much as possible.

Close the door.

2. Measure out the detergent

Pull out the dispenser drawer until it stops. Measure

out the amount of detergent recommended by the

manufacturer in a graduated cup and pour it into the

main wash compartment .

If you have selected the prewash function, pour

detergent into the appropriate compartment marked

3. Measure out the additive

If required, pour fabric softener into the compartment

marked , without exceeding the «MAX» mark.

C0065

C0064

P0004

132988120gb.qxd 08/06/2004 08.49 Pagina 15

10. Start the programme

Press the START/PAUSE button . The relevant

light will stop flashing and only the light relevant to

the phase that is in progress will remain lit.

If you have chosen a delayed start, the washing

machine will begin the countdown.

The display will show the duration of the programme

or the selected delay.

11. How to change a programme during

its cycle

Before you make any change, you must pause the

washing machine by pressing the START/PAUSE

button.

It is possible to change any phase before the

programme carries it out.

Changing the type of fabric or temperature is

possible, obviously, only during the washing phase.

If it is necessary to drain the water in order to change

the programme in progress, proceed as follows:

• PAUSE the machine by pressing the

START/PAUSE button;

• press the SKIP/RESET button repeatedly, until only

the DRAIN light remains lit;

• press the START/PAUSE button again.

When the water has been drained, the display shows

a blinking zero. You may now select a new

programme and press the START/PAUSE button to

start it.

12. How to cancel a programme

during its cycle

To cancel a programme that is being carried out, first

pause the washing machine by pressing the

START/PAUSE button, then press the SKIP/RESET

button repeatedly, until the display shows three

blinking dashes.

7. Select the spin speed or the RINSE

HOLD option

Press the SPIN SPEED button repeatedly, in

order to select the desired spin speed or the RINSE

HOLD option . The relevant light will light up.

If you select the RINSE HOLD option, the machine

will stop at the end of the programme with the water

still in the tub.

8. Select the desired options

Depress the relevant buttons to select the required

options.

9. Select the DELAY TIME

Before you start the programme, if you wish the

starting to be delayed, press the DELAY button (11)

repeatedly, or keep it pressed, to select the desired

delay. The selected delay time value (up to 23 hours)

will appear on the display for 3 seconds, then the

duration of the programme will appear again.

10. Start the programme

1200

900

700

500

132988120gb.qxd 08/06/2004 08.49 Pagina 16

ENGLISH

13. How to open the door during the

cycle of a programme

You can open the door, after having set the washing

machine to PAUSE, provided the following

conditions exist:

• the washing machine is not in the heating phase

beyond 55°C;

• the level of the water is not high;

• the drum is not turning.

If these requirements are met, when you pause the

washing machine, the door can be opened.

Should it not be possible to open the door, and

should it be absolutely necessary to do so, switch

the machine off by pressing the ON/OFF button.

After approximately 3 minutes, you can open the

door.

Pay attention to the level and temperature of the

water in the washing machine!

When you close the door and press the ON/OFF

button again, the washing machine will resume the

programme from the point where it had been

interrupted.

14. End of programme

At the end of the programme, the washing machine

stops automatically, gives an audible signal, and

displays a blinking zero.

If you had selected the RINSE HOLD or NIGHT

CYCLE option, START/PAUSE

button goes out and the door is locked, the

or pilot light remains lit, to indicate that the

water must be drained. The display shows a flashing

zero.

When the programme has been completed, a

blinking zero appears on the display and the audible

signal is given.

Press the SKIP/RESET button repeatedly to erase

the programme that has just been carried out. If

you omit to do this, the next time you switch the

washing machine on, the blinking zero will

appear on the display and you will hear the

audible signal.

Note: when you switch the machine on, if you must

erase the previously performed programme, it is also

sufficient to press the FABRIC button and select a

new programme.

Press the ON/OFF button to switch the machine off.

The relevant light will go out.

Remove the laundry from the washing machine.

Check whether the drum is completely empty, by

rotating it with your hand. The purpose of this is to

prevent any items of laundry from remaining

accidentally in the drum, where they might get

damaged in a subsequent wash (e.g. by shrinking) or

bleed colour into another load of laundry.

We advise you to close the water supply tap and

disconnect the plug from the socket.

Leave the door ajar in order to air the washing

machine.

132988120gb.qxd 08/06/2004 08.49 Pagina 17

Washing programmes

* The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on

the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. It refers to

the highest temperature for each wash programme.

** In compliance with EC directive 92/75 the consumption figures indicated on the Energy label refer to this

programme at 60°C + .

The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable

Woolmark products provided that the garments are washed according to the instructions on the garment label

and those issued by the manufacturer of this machine. Licence No. M9605.

Type of

laundry and

symbols on

labels

White cotton:

e.g. sheets,

tablecloths,

household

linen

Coloured

cotton: e.g.

shirts, blouses,

underwear,

towels, house-

hold linen

Synthetic

fabrics and

blends: e.g.

shirts, blouses,

underwear

Delicate fab-

rics: e.g.

acrylic fabrics,

viscose, poly-

ester,

synthetic

blends

Wool

5 kg

2.5 kg

2 kg

Max

load

Programme/

temperature

Available options

Consumption*

Energy

kWh

Water

litres

Time

h/min.

Cottons

60°-95°C

Cottons

60°-40°-30°C

Synthetics

60°-40°-30°C

Delicates

40°-30°C

Wool

40°-30°C

Hand wash

40°-30°C

Description of

programme

Main wash at

60°-95°C

3 rinses

Long spin

Main wash at

60°-40°-30°C

or cold wash

3 rinses

Long spin

Main wash at

60°-40°-30° or

cold wash

3 rinses

Short spin

Main wash at

40°-30°C or

cold wash

3 rinses

Short spin

Main wash at

40°-30°C or

cold wash

3 rinses

Short spin

Main wash at

40°-30°C or

cold wash

3 rinses

Short spin

1.9 47 2.20

1.1 44 1.59

0.85 50 1.27

0.55 53 58

0.35 52 57

Cottons+

5 kg

Cottons

60°

Main wash at

60°

3 rinses

Long spin

0.85 44 2.13

132988120gb.qxd 08/06/2004 08.49 Pagina 18

ENGLISH

Maintenance

1. Door seal

Check from time to time the door seal and eliminate

eventual possible objects that could be trapped in

the fold.

2. Bodywork

Clean the outside of the machine with warm water

and a neutral, non-abrasive household detergent.

Rinse with clean water and dry with a soft cloth.

Important: do not use methylated spirits, solvents or

Zanussi FJE1205 Kasutusjuhend

Kaubamärk: Zanussi

Mudel: FJE1205

Kategooria: Pesumasinad

Tüüp: Kasutusjuhend

Laadige alla PDF

aruanne

teistes keeltes

English: Zanussi FJE1205 User manual

Zanussi FJE1205 Kasutusjuhend

Zanussi FJE1205 Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid