Leht laaditakse ...
LED SOLAR SPOTLIGHT
Assembly and safety advice
LED-AURINKOVALAISIN
Asennus- ja turvaohjeet
LED-STRÅLKASTARE MED
SOLCELLER
Monterings- och säkerhetsanvisningar
REFLEKTOR SOLARNY LED
Wskazówki dotyczące montażu oraz
bezpieczeństwa
LED PROŽEKTORIUS SU
SAULĖS BATERIJA
Surinkimo ir saugos patarimas
LED-SOLAARKIIRGUR
Paigaldus- ja ohutusjuhised
AR SAULES BATERIJĀM
DARBINĀMS LED
PROŽEKTORS
Ieteikumi par uzstādīšanu un drošību
LED-SOLARSTRAHLER
Montage- und Sicherheitshinweise
LED SOLAR SPOTLIGHT
IAN 374873_2104
GB Page 5
FI Sivu 27
SE Sidan 49
PL Strona 71
LT Psl 93
EE Lehekülg
115
LV Lpp.
137
DE/AT/CH Seite
159
1.8-2.5m
5.0m 8.0m
90°
DC
B
A1
2
3
4
5
10
11
12
13
6
7
8
9
HG04465A
1.8-2.5m
5.0m 8.0m
90°
A
B C
D
E F
HG04465B
12
4
5
11 12
13
10
8
6
9
17
19 18
15
14
16
7
3
5GB
List of pictograms used ................ Page 6
Introduction ............................. Page 7
Intended use............................... Page 7
Description of parts ......................... Page 8
Technical data ............................. Page 9
Scope of delivery........................... Page 9
General safety instructions............ Page 10
Safety instructions for batteries/
rechargeable batteries....................... Page 11
Before use ............................... Page 13
Charging the rechargeable batteries ............ Page 14
Inserting / replacing batteries ........ Page 15
Installation .............................. Page 16
Start-up .................................. Page 21
Maintenance and cleaning ............ Page 22
Disposal.................................. Page 23
Warranty ................................ Page 24
6 GB
List of pictograms used
Direct current/voltage
CE mark indicates conformity with relevant
EUdirectives applicable for this product.
Motion detector range approx. 5 – 8 m
Detection angle of motion sensor: approx. 90º
Ingress protection (IP) type: IP44 (splash-proof)
Batteries included (Ni-MH)
Illumination time (after activation): approx.30seconds
7GB
LED SOLAR SPOTLIGHT
Introduction
We congratulate you on the purchase of your new product.
You have chosen a high quality product. The instructions for
use are part of the product. They contain important information
concerning safety, use and disposal. Before using the product,
please familiarise yourself with all of the safety information and
instructions for use. Only use the product as described and for the
specified applications. If you pass the product on to anyone else,
please ensure that you also pass on all the documentation with it.
Intended use
The product is intended to illuminate outdoor areas without
electrical connection. The product is suitable for use in private
household and is not intended for commercial use or for use in
other applications.
Not suitable for ordinary lighting in household room
illumination.
8 GB
Description of parts
[1] Solar panel
[2] ON/OFF switch
[3] Spotlight
[4] Sensor
[5] Dowel (mounting plate)
[6] Mounting plate
[7] Ball joint cover
[8] Screw (mounting plate)
[9] Slot
[
]
Front cover
[
]
Rechargeable battery
[
]
Battery compartment
[
]
Fixing screw (front cover)
[
]
Mounting bracket (HG04465B only)
[
]
Dowel (for mounting bracket) (HG04465B only)
[
]
Screw (for mounting bracket) (HG04465B only)
[
]
Connection cable (HG04465B only)
[
]
Plug (HG04465B only)
[
]
Socket (HG04465B only)
9GB
Technical data
Model no.: HG04465A or HG04465B
LEDs: 6 x 0.08 W
(LEDs are not replaceable.)
Operating voltage: 3.6 V
Rechargeable batteries: 3 x Ni-MH AA, 900 mAh,1.2 V
Degree of ingress protection: IP44 (splash-proof)
Motion sensor: Range: approx. 5 to 8 m
Detection angle: approx. 90º
Scope of delivery
Check immediately after unpacking that the parts are complete
and that the product is in proper condition.
1 LED solar powered spotlight, model HG04465A or
HG04465B
1 Mounting bracket (for solar panel) (HG04465B only)
1 Solar panel (HG04465B only)
2 Dowels (mounting plate)
2 Screws (mounting plate)
2 Dowels (mounting bracket) (HG04465B only)
2 Screws (mounting bracket) (HG04465B only)
1 Assembly, operating and safety instructions
10 GB
General safety instructions
BEFORE USING THE PRODUCT, PLEASE FAMILIARISE
YOURSELF WITH ALL OF THE SAFETY INFORMATION
AND INSTRUCTIONS FOR USE! WHEN PASSING THIS
PRODUCT ON TO OTHERS, PLEASE ALSO INCLUDE ALL THE
DOCUMENTS!
This product can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the product in a safe way and understand the hazards
involved. Children shall not play with the product. Cleaning
and user maintenance shall not be made by children without
supervision.
Never leave children unsupervised with the packaging
material. The packaging material represents a danger of
suffocation. Children frequently underestimate the dangers.
Keep children out of the area you are working in. A large
number of screws and other small parts are included with the
delivery. These may prove life-threatening if swallowed or
inhaled.
11GB
Do not use this product if you notice any damage!
The LEDs are not replaceable.
If the LEDs fail at the end of their life, the entire product must
be replaced.
Do not look directly into the light source (light bulb, LED etc.).
Do not look at the LED with an optical instrument (e.g.
magnifier).
The external flexible cable of this luminaire cannot be
replaced; if the cord is damaged, the luminaire shall be
destroyed (HG04465B only).
Safety instructions for batteries/
rechargeable batteries
m DANGER TO LIFE! Keep batteries/ rechargeable batteries
out of reach of children. If accidentally swallowed seek
immediate medical attention.
Swallowing may lead to burns, perforation of soft tissue, and
death. Severe burns can occur within 2 hours of ingestion.
12 GB
DANGER OF EXPLOSION! Never recharge
non-rechargeable batteries. Do not short-circuit
batteries/ rechargeable batteries and/ or open them.
Overheating, fire or bursting can be the result.
Never throw batteries/ rechargeable batteries into fire or
water.
Do not exert mechanical loads to batteries/ rechargeable
batteries.
Risk of leakage of batteries/ rechargeable batteries
Avoid extreme environmental conditions and temperatures,
which could affect batteries/ rechargeable batteries, e.g.
radiators/ direct sunlight.
If batteries/ rechargeable batteries have leaked, avoid
contact with skin, eyes and mucous membranes with the
chemicals! Flush immediately the affected areas with fresh
water and seek medical attention!
WEAR PROTECTIVE GLOVES! Leaked or damaged
batteries/ rechargeable batteries can cause burns on
contact with the skin. Wear suitable protective gloves at
all times if such an event occurs.
13GB
In the event of a leakage of batteries/ rechargeable
batteries, immediately remove them from the product to
prevent damage.
Only use the same type of batteries/ rechargeable batteries.
Do not mix used and new batteries/ rechargeable batteries.
Remove batteries/ rechargeable batteries if the product will
not be used for a longer period.
Risk of damage of the product
Only use the specified type of battery/ rechargeable battery!
Insert batteries/ rechargeable batteries according to polarity
marks (+) and (–) on the battery/ rechargeable battery and
the product.
Clean the contacts on the battery/ rechargeable battery and
in the battery compartment before inserting!
Remove exhausted batteries/ rechargeable batteries from the
product immediately.
Before use
Note: Remove all packaging materials from the product.
14 GB
Charging the rechargeable batteries
Note: The rechargeable batteries [
]
inside the product are fully
charged at delivery. However, they may have lost charge during
transport from the manufacturer to the retail location. Therefore
charge the rechargeable batteries [
]
prior to use. During summer,
initial charging will take at least 1 day in constant sunlight.
Set the ON/OFF switch [2] to the “ON“ position.
Note: In constant sunlight (depending on the season) drained
rechargeable batteries [
]
should take 2 to 10 days to charge.
Note: The built-in charging controller of the product prevents the
rechargeable batteries [
]
from overcharging.
Replace the rechargeable batteries [
]
if light output does
not improve after charging (Fig.C: HG04465A or Fig.E:
HG04465B).
15GB
Inserting / replacing batteries
Note: The rechargeable batteries [
]
are pre-installed. Only use
batteries as stated in the “Technical data” chapter. To remove the
rechargeable batteries [
]
, switch the spotlight [3] off using the
ON/OFF switch [2].
Open the battery compartment [
]
on the back side
of the spotlight [3] by loosening the fixing screws [
]
counterclockwise to remove the front cover [
]
(Fig.C:
HG04465A or Fig.E:HG04465B).
Remove the old rechargeable batteries [
]
.
Insert the new rechargeable batteries [
]
. Use only batteries
of the specified type (see “Technical data”).
Note: When inserting the battery, ensure the correct polarity!
This is indicated in the battery compartment [
]
.
Close the battery compartment [
]
again with the front cover
[
]
and fix the front cover [
]
by turning the fixing screws [
]
clockwise.
Note: Make sure the sealing ring is secured correctly before
closing the battery compartment, otherwise the ingress
protection (IP) cannot be guaranteed.
16 GB
Installation
Note: The included mounting material is suitable for ordinary
solid concrete or masonry construction. Other wall substrates
may require other fastening materials. Seek specialist advice if
necessary.
Note: You will need an electric drill.
m CAUTION! RISK OF INJURY! Read the operating
instructions for your drill.
m CAUTION! Ensure that you do not damage any electricity
cables in the wall or ceiling.
When selecting the mounting location, pay attention to the
following:
Ensure that the spotlight [3] illuminates the desired area. You
can swivel the spotlight [3] into the desired position.
Ensure the sensor [4] covers the desired area. The sensor[4]
has a maximum coverage range of approx. 5 to 8 m, with a
coverage angle of about 90° (depending on the mounting
height – a height from 1.8 to 2.5 m is ideal)
(Fig. D: HG04465A or Fig. F: HG04465B).
Ensure the sensor [4] is not illuminated at night by street
lighting. This can influence its functioning.
17GB
Ensure that the solar panel [1] is mounted in a place with
direct sunlight.
Ensure that the solar panel [1] is not installed where there are
strong temperature fluctuations, e.g. due to heating devices.
Ensure that the solar panel [1] is installed far away from
unnatural light sources and in southern direction.
Ensure that the connection cable [
]
of the solar panel [1]
can reach the spotlight [3]. Max. distance between the solar
panel [1] and the spotlight [3] is approx. 2.5 m (HG04465B
only).
For HG04465A:
Carefully fold the solar panel [1] upwards.
Remove the mounting plate [6] from the spotlight [3] by
loosening the screws of the ball joint cover [7] (Fig. B).
Use the holes of the mounting plate [6] intended for the
screws [8] to mark the drill holes.
Now drill the fixing holes (Ø 8 mm, depth approx. 40 mm).
Before drilling the fixing holes, ensure there are no gas, water
or electrical lines that could be drilled into or damaged in the
area where you will be drilling.
Insert the dowels [5] into the drill holes (Fig. B).
18 GB
Attach the mounting plate [6] using the screws [8] provided
(Fig. B).
Ensure that the solar panel [1] is orientated towards the sun.
Now place the spotlight [3] towards the mounting plate [6].
Ensure that the ball joint of the mounting plate [6] is correctly
inserted into the slot [9] of the spotlight [3]. Then, close the
ball joint cover [7] by tightening the screws clockwise (Fig. B).
Set the ON/OFF switch [2] on the spotlight [3] to the “ON“
position (Fig. A).
The rechargeable batteries [
]
will now charge when there is
sufficient solar radiation.
For HG04465B:
Remove the mounting plate [6] from the spotlight [3] by
loosening the screws of the ball joint cover [7] (Fig. B).
Use the holes of the mounting plate [6] intended for the
screws [8] to mark the drill holes.
Now drill the fixing holes (Ø 8 mm, depth approx. 40 mm).
Before drilling the fixing holes, ensure there are no gas, water
or electrical lines that could be drilled into or damaged in the
area where you will be drilling.
19GB
Insert the dowels [5] into the drill holes (Fig. B).
Attach the mounting plate [6] using the screws [8] provided
(Fig. B).
Now place the spotlight [3] towards the mounting plate [6].
Ensure that the ball joint of the mounting plate [6] is correctly
inserted into the slot [9] of the spotlight [3]. Then, close the
ball joint cover [7] by tighten the screws clockwise (Fig. B).
Now use the holes in the mounting bracket [
]
intended for
the screws [
]
to mark the drill holes (Ø 8 mm, depth approx.
40 mm).
Ensure that you can connect the spotlight [3] using the
connection cable [
]
to the solar panel [1] .
Now drill the fixing holes. Before drilling the fixing holes,
ensure there are no gas, water or electrical lines that could be
drilled into or damaged in the area where you will be drilling.
Insert the dowels [
]
into the drill holes (Fig. C).
20 GB
Attach the mounting bracket [
]
using the screws [
]
.
Place the solar panel [1] into the mounting bracket [
]
(Fig. C).
Ensure that the solar panel [1] is orientated towards the sun.
Insert the plug [
]
into the socket [
]
(Fig. D).
Set the ON/OFF switch [2] on the spotlight [3] to the “ON“
position (Fig. A).
The rechargeable batteries [
]
will now charge when there is
sufficient solar radiation.
When selecting the mounting location for the solar panel [1], pay
attention to the following:
The solar panel [1] needs to be as directly exposed to sunlight as
possible. Even partial shading of the solar panel [1] during the
day can have a significant influence on charging.
Cardinal direction:
Orientation towards the south is optimum. Orienta tions with slight
deviations towards the west are preferable to those with slight
deviations towards the east.
/
