16
WARNING Fire and explosion hazard!
Theunitisnotpermittedtobeusedfortheextractionof
inammablegases.
Theunitmustnotbeexposedtotemperaturesabove
50°C,nakedameorcondensedsolvents.
The organisation operating the unit is responsible for the
observanceofthelegallimitsfornoxioussubstancesat
the place of work.
Theltrationsystemmayonlybeputintooperationifitis
in perfect working order.
Intended use of the soldering station/ desoldering
stationalsoincludestherequirementthatyou
adheretotheseinstructions,
observeallotheraccompanyingdocuments,
complywithnationalaccidentpreventionguidelines
applicable at the place of use..
The manufacturer will not be liable for unauthorised
modicationstothedevice.
User groups
Duetodifferingdegreesofriskandpotentialhazards,sever-
alworkstepsmayonlybeperformedbytrainedexperts.
Work step User groups
Installationofcomplex
pipesystemswith
multipleextractorarms
connected
Specialist personnel with
technical training
Technical trainees under the
guidance and supervision of
atrainedexpert
Replacing electrical repla-
cement parts Electricians
Technical trainees under the
guidance and supervision of
atrainedexpert
Specicationofmainte-
nance intervals Safetyexpert
Operation
Filter change
Non-specialists
Operation
Notice
Theunitmayemitdustfromthemainlteraftertrans-
portation. Make sure that the unit is put into service in
a suitable room.
CAUTION Ahighnoxiousgasconcentrationwill
cause the activated charcoal to heat up.
Toavoidoverheating,theunitshouldberunwithout
noxiousgasesforseveralminutesbeforeswitchingoff.
Put the tool into operation as described in the chapter
„Placingintooperation“.
Please adhere to the operating instructions of the
connected devices.
Checktoseeifthemainsvoltagematchestheratings
on the nameplate.
Make sure the machine is switched off before plugging
in.
Optimalgasltrationisachievedasfollows:
Temperatureofprocessairingaslter<38°C
Relativehumidity<60%
Gasmolecules>30g/mol(betterltrationresultsare
achievedwithlargermolecules)
Boilingpointofthegasmolecules>0°C
Care and maintenance
WARNING
Before doing any work on the machine, pull the
plug out of the socket.
Theunitmustnotbealteredormodiedinanyway!
Repairs must always be referred to a Weller-trained
specialist.
Useoriginalreplacementpartsonly.
Filter change
year
MIN 1x Toensurethattheltrationsystem
functionsproperly,thecompactlter
must be replaced as follows
atleastonceayearor
ifthemaximumallowable
workplaceconcentrationisexceeded
or
as per maintenance schedule
Notice
Differentuxesanduxconstituentsandtheamountof
andsizeofdustparticlesintheextractedairwillsigni
cantlyeffecttheltersworkinglife.Submicronparticles
intheextractedairincreasewhensolderingorwelding
to varnish insulated wire.
Thesuspendedmatterlterandthebroadbandgas
lterarecomplementarytooneanotherandcanbe
replacedtogetherasacompactlter.Thecompact
ltermustbechangedonceayearinordertoensure
itisfullyfunctional.Thenedustlter(ltermat)isthe
preliminarystageofthecompactlterandtherefore
mustbereplacedmorefrequently.
Itisstronglyrecommendedthatthecompactlterbe
replacedafternomorethan10nedustlterchanges.
An alarm sounds and the yellow warning light a-
shes: Recommendedservicelifeoflterhasexpired.
(seeOperatingtimelterdisplay/Extractioncapacity
lterdisplay)
An alarm sounds and the red warning light is lit
continuously: Extractioncapacityistoolow.Switch
offthelterunit.Checkthenozzles,tubesandext-
ractorarms,andcleanthemifnecessary.Ifthealarm
GB ENGLISH