HOUSEGARD SA703 Kasutusjuhend

SMOKE ALARM PEBBLE LINK

USER MANUAL

SA703 Ver: 220617

Consumer contact:

GPBM Nordic AB

Argongatan 2 B

SE-431 53 Mölndal, Sweden

info@housegard.com

GBSNDKEST FIND

ENGLISH 4–24

SVENSKA 25–45

NORSK 46–66

DANSK 67–87

SUOMI 88–108

EESTI KEEL 109–129

DEUTSCH 109–129

4

Congratulations on the purchase of your new smoke alarm device. We

recommend that you spend some time reading this instruction manual in order

to fully understand all the operational features. You will also ﬁnd some hints and

advice to help you resolve any issues. Read all the safety instructions carefully

before use and keep for future reference.

The Housegard smoke alarm is designed to detect smoke particles, to reduce the

number of false alarms and to give an early warning if a ﬁre occurs. Its operation

depends on correct positioning and maintenance.

FEATURES

• Wireless connection

• Connect up to 12 pcs

• Sealed for life battery 10 years

• Both screws and adhesive 3M tape included

• High sensitivity and stability

• Test/Pause and Learn button

• LED diode indicates normal operation

• Low voltage warning

• Alarm memory

• End of life indication

• Twist aid accessory for mounting plate

• Dust cover included

GB USER MANUAL OPTICAL

SMOKE ALARM PEBBLE LINK

5

GBSNDKEST FIND

TECHNICAL SPECIFICATIONS

Model No: SA703

Detection type: Photoelectric

Power source: DC3V lithium

Standby current: <2 uA

Alarm current: <120 mA

Working frequency: 868,3 MHz

Frequency band: 868-868,6 MHz

Eective radiated power: ≤ 4 dBm

Transmission distance open air: 100 m

Alarm sound level: 85 dB at 3 m

Operating temperature: -10 °C to +40 °C

Ambient humidity: ≤ 95%

6

SLOT SLOT

POSITIONING COLUMN

BATTERY PIN +

BATTERY PIN –

SCREW HOLE

BATTERY +

BATTERY – HOOK

HOOK

POSITIONING GROOVE

TEST/HUSH BUTTON /INDICATOR LEARN BUTTON / INDICATOR

BUZZER

7

GBSNDKEST FIND

IMPORTANT SAFETY INFORMATION

• The smoke alarm device is battery-powered. It will not work without battery, or if

the battery is dead, removed or not correctly connected. Use only the speciﬁed

type of battery. DO NOT connect the smoke alarm device to any type of detector

or equipment other than what is stated in this manual.

• The test button provides a full test of all the smoke alarm’s functions. No other test

methods are required. Test smoke alarm devices every week to check that they are

working properly.

• Do not remove or disconnect the battery to stop false alarms, as this will cause the

smoke alarm to lose important functionality. Open a window or ventilate the air

around the smoke alarm device to stop the alarm and/or press the pause button.

• The smoke alarm device must be installed in line with all local and national rules

and regulations on installation.

• The smoke alarm device is intended for use in houses. In apartment blocks, each

apartment should be ﬁtted with its own smoke alarm device. This smoke alarm

device is not suitable for use in non-residential buildings. The smoke alarm device is

not a replacement for a complete alarm system as required under law or by the ﬁre

safety authorities.

• There may be reasons why a person in a household might not hear the alarm (e.g.

noise, deep sleep, impaired hearing). If you suspect that a person in the household

will not react to the smoke alarm device, specialist alarms should be installed.

• The smoke alarm device detects combustion particles (smoke) in the air. It does not

react to ﬂames or gas. The smoke alarm device is designed to give o an audible

alarm if a ﬁre is developing.

• No smoke alarm devices are entirely reliable and they cannot give a 100%

guarantee to protect life and property against ﬁre. The smoke alarm device is no

replacement for insurance. Homeowners and tenants should take out life and home

insurance.

The smoke alarm device should be tested regularly and replaced

8

DUST COVER INCLUDED

If you have built, renovated or extended a house, the ﬁre alarm should be installed

after the ﬁnal cleaning. The dust cover should be removed by the occupants after

they have moved in to avoid unnecessary dust/particles in the ﬁre alarm.

POSITIONING THE SMOKE ALARM DEVICE

In order to give an early warning, the smoke alarm needs to be installed where

the ﬁre occurs. Housegard therefore recommends that you install a smoke alarm

device in every room and on every ﬂoor.

• Install a smoke alarm device in all separate bedrooms and in rooms

commonly occupied.

• In homes with several storeys, a smoke alarm device should be installed at

the top of every staircase between each storey.

• In the basement, a smoke alarm device should be installed in the ceiling at

the foot of the stairs.

• In bedrooms where people sleep with closed doors, there should always be

a smoke alarm ﬁtted in the bedroom.

• Install a smoke alarm device in every room where there is a potential risk

of ﬁre.

9

GBSNDKEST FIND

• If you install the smoke alarm in a passageway whose width is less than 3 m,

install it in the middle and install one unit every 12 m.

• Install the smoke alarm device in the middle of the ceiling. If you can’t,

install it at least 0,5 m from the wall (wall mounting not recommended).

• If you install the smoke alarm on sloped or peaked ceiling, the installation

position shall be at least 1 m from the highest point (see image below).

• At least 1,5 m from ﬂuorescent lamp or neon lamp. (In case of electronic

interference).

• At least 3 m from the bathroom.

• At least 6 m from the kitchen or stove.

• At least 30 cm from the lamps.

KEY:

Minimal protection

Recommended/more substantial protection

∆ Smoke alarm devices with a pause function are recommended

10

SMOKE ALARM DEVICES SHOULD NOT BE PLACED IN

THE FOLLOWING LOCATIONS

• In the kitchen, near the cooker, where smoke from cooking could cause false

alarms.

• In areas of high air humidity, such as bathrooms or near dishwashers or

washing machines, where steam and moisture could cause false alarms.

• Near fans and ventilation ducts, where air ﬂows may prevent smoke from

reaching the smoke alarm device.

• Near light sources and electrical equipment that emit an electromagnetic ﬁeld.

• Near a ﬁreplace or stove with an open ﬁre.

• At the top of a V-shaped ceiling, where air pockets could stop the smoke from

reaching the smoke alarm.

• In a garage, where exhaust fumes could cause false alarms.

• In dusty and dirty areas, where the dust and dirt could damage the smoke

alarm device.

• In rooms where the temperature may fall below -10 °C or rise above +40 °C, or

in rooms with large temperature variations.

• Areas that have large metal surfaces that could block the RF signal between

units.

WARNING: Incorrect positioning may lead to reduced reliability and false alarms.

11

GBSNDKEST FIND

PREPARING AND PROGRAMMING

Important: The SA703 smoke alarms are equipped with transmitters and

receivers, so they can communicate with each other. For this function to work, the

smoke alarms must be programmed to link up.

Important: The signal range may vary depending on position, the design of the

building and its materials. Make sure that all the installed smoke alarms are within

signal range.

Important: Protect your hearing. Smoke alarm devices emit a loud audible signal.

We recommend that you always use earplugs or other hearing protection when

testing your smoke alarms.

GB

12

TWIST MOUNTING PLATE

CLOCKWISE

ALIGN THE POSITIONING

GROOVE

ACCESSORY

FITTING THE MOUNTING PLATE WITH BUILT-IN BATTERY

We suggest that you interconnect the alarms before you install the product to the

ceiling, to make your operation more ecient.

Mount the smoke alarm to the mounting plate and twist mounting plate

clockwise. Then the smoke alarm enters standby condition. Note that the smoke

alarm is not interconnected with other units now.

Note 1. If you can’t rotate the alarm, make sure to insert the hook into the slot,

please check if the column aligns with the position groove.

Note 2. If you can’t rotate the mounting plate easily, please use or twist aid

accessory in package.

13

GBSNDKEST FIND

CONNECT THE ALARMS

Choose one of the smoke alarms as the Master unit and mark it with an M on the

back, so you know which one it is later on. The master unit is used to send the

radio code to the other alarms, so they all connect up.

1. Press the LEARN button twice on the MASTER unit. Then the LEARN

button indicator shall be green. That means this unit will be set in learning

mode.

2. Press the LEARN button of all the other SLAVE alarms that need to be

interconnected. The LEARN button indicator will be red on those units.

MASTER UNIT

X2

SLAVE UNIT

X1

14

3. Press shortly the TEST button on the MASTER alarm.

4. All interconnected slave units will go into alarm mode and LEARN button

indicator will be ﬂashing green.

5. Learning of interconnection is completed.

MASTER UNIT

X1

SLAVE UNIT

15

GBSNDKEST FIND

TEST THE CONNECTED ALARMS

Press and hold down the TEST button on any interconnected smoke alarm until

all alarms sound.

INTERCONNECT ADDITIONAL SLAVE UNITS

1. Make sure to use the MASTER used ﬁrst time. Follow above instruction to

interconnect additional SLAVES into the systems.

2. After successful interconnection, test the system again by holding down

the test button until all alarms sound.

DELETE PROGRAMMING (Re-setting)

Press and hold the LEARN button until the LEARN button indicator has stopped

ﬂashing green. Now the programming is deleted for that alarm.

HOLD

16

INSTALLATION WITH SCREWS

1. Remove the mounting plate on the back of the smoke

alarm by twisting it anti clockwise.

2. Hold the mounting plate against the selected instal-

lation position on the ceiling, mark the centre of the

holes with a pencil. Drill a hole through the pencil

marks and use the enclosed screws and anchors to

secure the mounting plate.

3. Place the smoke alarm device against the mounting

plate and twist the smoke alarm device clockwise until

it clicks into place.

4. Press the test button to test the smoke alarm device.

EASY INSTALLATION WITH TWO-SIDED ADHESIVE

TAPE

Make sure that the installation surface is ﬂat and clean. If the surface is rough, we

recommend that you install the smoke alarm with the help of the screws.

1. Remove one side of the 3M tape protection

2. Attach the tape on the base plate on back of the smoke

alarm. Press for 5 seconds.

3. Remove the second side of the 3M tape protection.

4. Place the smoke alarm according to the manual. Press

the smoke alarm for ﬁve seconds against the ceiling to

make sure that it is well attached

5. Press the test button to test the smoke alarm device.

17

GBSNDKEST FIND

OPERATION

Normal Mode

In standby condition the TEST/HUSH indicator ﬂashes every 344 seconds to

indicate that the smoke alarm is operating properly. The smoke alarm detects

smoke every 10 seconds. When it senses smoke, the alarm sounds and the TEST/

HUSH indicator ﬂashes red at the same time, until the air is clear.

Pause mode (Low sensitivity)

The smoke alarm is desensitized by pushing the TEST/HUSH button. The alarm

indicator ﬂashes every 10 seconds and no audible sound will be heard during 9

minutes, unless smoke becomes denser. If the smoke becomes denser, the alarm

will override the pause mode. The pause mode will end automatically after 9

minutes or by pressing the TEST/HUSH button again.

Low battery warning

The low battery warning will indicate when the voltage is too low, the smoke

alarm will then make short beeps every 43 seconds.

Test mode

By pressing the TEST button the smoke alarm will enter alarm mode. The unit will

make beeps every 0,5 second and the TEST/HUSH indicator will ﬂash red.

Alarm Memory

This smoke alarm is equipped with an alarm memory, which provides a visual

indication when an alarm has been activated. When the TEST/HUSH button

indicator ﬂashes green 3 times every 43 seconds, that means alarm has been

made during the last 24 hours. Please check if there is ﬁre risk in detection

area. This indication will end after 24 hours or when pushing Test/Hush button.

First time you press test/mute button after alarm is made, the smoke alarm will

indicate by special alarm mode.

18

End of life mode

The time and working environment will cause the degeneration of smoke

chamber. When the product makes 3 short beeps every 43 seconds, it indicates

end-of-unit-life. You should replace the smoke alarm with a new one.

MEANING OF THE DIFFERENT LED AND ALARM SIGNALS

STATUS RED LED GREEN LED ALARM SIGNAL DESCRIPTION

NORMAL MODE Flashes once/344

sec.

The smoke

alarm is working

normally.

PAUSE MODE Flashes once/10

sec.

Exits pause mode

after 9 minutes.

LOW BATTERY Flashes once/344

sec.

One beep/

43 sec.

Replace the

unit as soon as

possible.

ALARM/ TEST

MODE.

Flashes conti-

nuously.

One beep/

0,5 sec.

Evacuate/

Validates the

functionality.

ALARM MEMORY 3 ﬂashes every

43 sec. for 24h.

Indicates by one

distinct beep

during the ﬁrst

test.

END OF LIFE Three alarm

signals every

43 sec.

Replace the

alarm immedi-

ately

19

GBSNDKEST FIND

CAUSES AND REMEDIES FOR FALSE ALARMS

A smoke alarm device detects and reacts to smoke particles in the air. The smoke

particles set o the smoke alarm device. This function means that the smoke alarm

device will also react to dust particles, moisture or other particles in the form of

pollen, insects etc. These factors are usually the cause of a false alarm.

CAUSE OF ERROR ACTION

Steam and moisture. A false alarm

may occur if the smoke alarm device

is placed too close to a bathroom,

laundry room, or other location with

high air humidity.

Place the smoke alarm device at least

3 metres from any bathroom, laundry

room, or other location where high air

humidity may occur.

Dust and dirt. Since air passes freely

through the detection chamber, the

smoke alarm device will always attract

some dust and pollen particles. This

can lead to a false alarm. The smoke

alarm device may also become more

sensitive for this reason, which could

cause false alarms. In addition, dirt will

collect over time, as the smoke alarm

device ages, which may result in false

alarms.

Regularly vacuum the smoke alarm

device, using a plastic nozzle to avoid

damaging the electronics. Avoid

ﬁtting smoke alarm devices in places

with a lot of dust and dirt. You can put

a ‘hat’ over the smoke alarm device

or remove it entirely while you are

carrying out renovation work at home

that involves sawing, sanding, etc.

20

Draughts, dust and air ﬂows. False

alarms may be caused by the smoke

alarm device being placed too close to

doors, windows, ventilation systems,

fans, air ducts, heat pumps or suchlike.

This can lead to dust particles being

carried up into the detection chamber.

Do not install smoke alarm devices in

a draughty location, close to windows

or doors, ventilation, fans, air ducts,

heat pumps or suchlike. Find a better

location for the smoke alarm device,

further away from draughts and air

ﬂows.

Temperature variations. Temperature

variations may lead to condensation

in the detection chamber. This may

happen, for example, if the smoke

alarm device is placed in a room

where windows are opened for ven-

tilation in the winter, or close to exits,

balcony doors or other places that

switch between hot and cold.

Avoid ﬁtting smoke alarm devices

in rooms with rapid temperature

changes or close to windows and

doors that are frequently opened and

closed. Move the smoke alarm device

to a place with a more even and stable

temperature.

Generally unfavourable positions.

Incorrect positioning in an unstable

indoor environment, a draughty area,

close to electronic apparatus (EMC)

and lighting may cause a false alarm.

Place smoke alarm devices at least

6 metres from open ﬁres, stoves or

other heating devices; 2 metres from

ventilation ducts, heat pumps and

air conditioning; 1,5 metres from light

bulbs and ﬂuorescent tubes.

Leht laadib ...

HOUSEGARD SA703 Kasutusjuhend

HOUSEGARD SA703 Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid