Milwaukee M18 CAG125X Original Instructions Manual

M18 CAG115X

M18 CAG125X

M18 CAG115XPD

M18 CAG125XPD

M18 CAG115X

Original instructions

Originalbetriebsanleitung

Notice originale

Istruzioni originali

Manual original

Oorspronkelijke

gebruiksaanwijzing

Original brugsanvisning

Original bruksanvisning

Bruksanvisning i original

Alkuperäiset ohjeet



Orijinal iş

Původním návodem k







Eredeti használati utasítás

Izvirna navodila

Originalne pogonske upute

Instrukcijâm oriěinâlvalodâ

Originali instrukcija

Algupärane kasutusjuhend









Instrucţiuni de folosire originale









Technical Data,Safety Instructions, Specied Conditions of Use,

EC-Declaration of Conformity, Batteries, Maintenance, Symbols

Please read and save

these instructions!

English

15

Technische Daten, Sicherheitshinweise, Bestimmungsgemäße Verwendung,

CE-Konformitätserklärung, Akkus, Wartung, Symbole

Bitte lesen und

aufbewahren!

Deutsch

20

Caractéristiques techniques, Instructions de sécurité, Utilisation conforme aux

prescriptions, Déclaration CE de Conformité, Accus, Entretien, Symboles

A lire et à conserver

soigneusement

Français

25

Dati tecnici,Norme di sicurezza,Utilizzo conforme, Dicharazione di Conformità CE,

Batterie, Manutenzione, Simboli

Si prega di leggere e

conservare le istruzioni!

Italiano

30

Datos técnicos, Instrucciones de seguridad, Aplicación de acuerdo a la nalidad,

Declaracion de Conformidad CE, Bateria, Mantenimiento, Símbolos

Lea y conserve estas

instrucciones por favor!

Español

35

Características técnicas, Instruções de segurança, Utilização autorizada,

Declaração de Conformidade CE, Acumulador, Manutenção, Symbole

Por favor leia e conserve

em seu poder!

Português

40

Technische gegevens, Veiligheidsadviezen, Voorgeschreven gebruik van het

systeem, EC-Konformiteitsverklaring, Akku, Onderhoud, Symbolen

Lees en let goed

op deze adviezen!

Nederlands

45

Tekniske data, Sikkerhedshenvisninger, Tiltænkt formål,

CE-Konformitetserklæring, Batteri, Vedligeholdelse, Symboler

Vær venlig at læse

og Opbevare!

Dansk

50

Tekniske data, Spesielle sikkerhetshenvisninger, Formålsmessig bruk,

CE-Samsvarserklæring, Batterier, Vedlikehold, Symboler

Vennligst les og oppbevar!

Norsk

55

Tekniska data, Säkerhetsutrustning, Använd maskinen Enligt anvisningarna,

CEFörsäkran, Batterier, Skötsel, Symboler

Läs igenom och spara!

Svenska

60

Tekniset arvot, Turvallisuusohjeet, Tarkoituksenmukainen käyttö,

Todistus CE-standardinmukaisuudesta, Akku, Huolto, Symbolit

Lue ja säilytö!

Suomi

65

Τεχνικά στοιχεία, Ειδικές υποδείξεις ασφάλειας, Χρήση σύμφωνα με το σκοπό

προορισμού, Δήλωση πιστότητας ΕΚ, Μπαταρίες, Χαρακτηριστικά, Συντήρηση, Σύμβολα.

Ελληνικά

70

Teknik veriler, Güvenliğiniz için talimatlar, Kullanim, CE uygunluk beyanice,

Akü, Bakim, Semboller

Lütfen okuyun ve saklayın

Türkçe

75

Technická data, Speciální bezpečnostní upozornění, Oblast využití,

Ce-prohlášení o shodě, Akumulátory, Údržba, Symboly

Po přečtení uschovejte

Česky

80

Technické údaje, Špeciálne bezpčènostné pokyny, Použitie podl’a predpisov,

CE-Vyhlásenie konformity, Siet’ová prípojka, Údrzba, Symboly

Prosím prečítať a uschovať!

Slovensky

85

Dane techniczne, Specjalne zalecenia dotyczące bezpiecze´nstwa, Użytkowanie zgodne z

przeznaczeniem, Świadectwo zgodności ce, Podłączenie do sieci, Gwarancja, Symbole

Należy uważnie przeczytać i

zachować do wglądu!

Polski

90

Műszaki adatok, Különleges biztonsági tudnivalók, Rendeltetésszerű használat,

Ce-azonossági nyilatkozat, Hálózati csatlakoztatás, Karbantartás, Szimbólumok

Olvassa el és őrizze meg

Magyar

95

Tehnični podatki, Specialni varnostni napotki, Uporaba v skladu z namembnostjo,

Ce-izjava o konformnosti, Omrežni priključek, Vzdrževanje, Simboli

Prosimo preberite

in shranite!

Slovensko

100

Tehnički podaci, Specijalne sigurnosne upute, Propisna upotreba,

CE-Izjava konformnosti, Priključak na mrežu, Održavanje, Simboli

Molimo pročitati i sačuvati

Hrvatski

105

Tehniskie dati, Speciālie drošības noteikumi, Noteikumiem atbilstošs izmantojums,

Atbilstība CE normām, Tīkla pieslēgums, Apkope, Simboli

Pielikums lietošanas pamācībai

Latviski

110

Techniniai duomenys, Ypatingos saugumo nuorodos, Naudojimas pagal paskirti,

CE Atitikties pareiškimas, Elektros tinklo jungtis, Techninis aptarnavimas, Simboliai

Prašome perskaityti

ir neišmesti!

Lietuviškai

115

Tehnilised andmed, Spetsiaalsed turvajuhised, Kasutamine vastavalt otstarbele,

EÜ Vastavusavaldus, Võrku ühendamine, Hooldus, Sümbolid

Palun lugege läbi ja hoidke alal!

Eesti

120

     

      

Пожалуйста прочтите и

сохраните эту инструкцию.

Pусский

125

        

       

Моля прочетете и запазете!

Български

131

Date tehnice, Instrucţiuni de securitate, Condiţii de utilizare specifcate,

Declaraţie de conformitate, Acumulatori, Intreţinere, Simboluri

Va rugăm citiţi şi păstraţi

aceste instrucţiuni

Română

136

       

     БАТЕРИИ њ 

Ве мoлиме прочитаjте го и

чувајте го ова упатство!

Мaкeдohcки

141

Технічні характеристики, Вказівки З Техніки Безпеки, Використання за призначенням,

Сертифікат Відповідності Вимогам Єс, Акумуляторна, Обслуговування, Символи

Прочитайте та збережіть

цю інструкцію.

Українська

146

















155

TIP

III

V

IX

II

VIII

VIIV

VII

I



Zubehör

Accessoires

Accessorio

Accessorio Acessório

Toebehoren

Tilbehør

Tillbehör

Lisälaite



Aksesuar

řš

Príslušenstv



Azokat a tartozékokat

Oprema

Piederumi

Priedas

Tarvikud





Accesoriu









2

I

1.

2.

3

I

78-100 %

33-54 %

55-77 %

10-32 %

<10 %

4

I

A

B

II

5

I

III

1.

2.

3.

1

2

4.

6

IV

0°

30°

60°

30

°

60

°

30

°

60

°

0

°

30°

7

I

V

2.

1.

3.

< 6 mm

> 6 mm

4.

8

V

3.

2.1.

9

VI

Stop

Start Stop

Start

M18 CAG115X / M18 CAG125X

M18 CAG115XPD / M18 CAG125XPD

1

2

10

VI

Startup protection:

When switched on, the machine will not start up after vol-

tage breakdown. To continue working, switch the machine

o and then on again.

Wiederanlaufschutz:

Eingeschaltete Maschine läuft nach Spannungsausfall

nicht wieder an. Um weiter zu arbeiten Maschine aus- und

wieder einschalten.

Dispositif de protection contre un redemarrage

Après une coupure de tension, la machine enclenchée

ne redémarre pas. Pour continuer à travailler, il convient

d’éteindre la machine et de l’enclencher à nouveau.

Protezione contro il riavvio

La macchina accesa non riparte in seguito alla caduta della

tensione. Per poter continuare a lavorare bisogna prima

spegnere e poi riaccendere la macchina.

Protección contra el rearranque

La máquina conectada no se vuelve a poner en marcha

después de un fallo de corriente. Para continuar el trabajo,

desconectar y volver a conectar la máquina.

Protecção de reinício

Quando está ligada, após uma falha de energia a máquina

não retoma o seu funcionamento. Para prosseguir o tra-

balho, desligar a máquina e voltar a ligá-la.

Herstartbeveiliging

Na spanningsuitval schakelt de machine niet automatisch

weer in. Schakel de machine uit en weer in om door te

kunnen werken.

Genstartsbeskyttelse

I tilfælde af spændingsudfald, mens maskinen kører, går den

ikke i gang igen, når spændingen kommer tilbage. For at

genoptage arbejdet skal maskinen slukkes og tændes igen.

Automatisk gjenstartsbeskyttelse

En påslått maskin begynner ikke automatisk å gå igjen etter

strømbrudd. For å kunne fortsette å arbeide må maskinen

skues av og så på igjen.

Återstartsskydd

En påslagen maskin startar inte själv efter ett strömavbrott.

Stäng först av och slå sedan på maskinen igen för att

fortsätta att arbeta.

Uudelleenkäynnistyssuoja

Päällekytketty kone ei käynnisty sähkökatkon jälkeen

uudestaan. Työn jatkamiseksi tulee kone sammuttaa ja

käynnistää uudelleen.

Προστασια επανεκκινησης

Η ενεργοποιημένη μηχανή δεν ξεκινά πάλι από μόνη της

μετά από μια πτώση ρεύματος. Για να συνεχίσετε την

εργασία, απενεργοποιείτε και ενεργοποιείτε πάλι τη μηχανή.

Tekrar çaliştirmada koruma

Çalıştırılan makine voltaj kaybından sonra yeniden çalışmaz.

Makineyi tekrar çalıştırmak için kapatın ve tekrar açın.

Ochrana proti opětovnému náběhu

Zapnutá rozbrušovačka se v případě výpadku proudu po

jeho opětovném zapnutí sama nerozběhne. K pokračování

práce se rozbrušovačka musí vypnout a opět zapnout.

Ochrana proti opätovnému nábehu

Zapnutá rozbrusovačka sa v prípade výpadku prúdu po

jeho opätovnom zapnutí sama nerozbehne. K pokračovaniu

práce sa rozbrusovačka musí vypnúť a opäť zapnúť.

Zabezpieczenie przed ponownym uruchomieniem

Włączone urządzenie nie uruchamia się z powrotem po

ustąpienia zaniku napięcia. Aby móc kontynuować pracę,

urządzenie należy wyłączyć, a potem z powrotem włączyć.

Újraindulás elleni védelem

A bekapcsolt gép feszültségkimaradás után ismét elindul. A

munka folytatásához a gépet ki és újra be kell kapcsolni.

Zaščita pred ponovnim zagonom

Vklopljen stroj se po izpadu napetosti ponovno ne zažene.

Za nadaljevanje dela stroj izklopite in ponovno vklopite.

Zaštita protiv ponovnog pokretanja

Uključeni stroj poslilje nestanka napona više ne starta. Da

bi se dalje radilo, stroj isključiti i ponovno uključiti.

Aizsardzība pret atkārtotu palaišanu

Pārtrūkstot strāvas padevei, ieslēgtā ierīce no jauna

neieslēdzas. Darba turpināšanai ierīci izslēgt un ieslēgt no

jauna.

Apsauga nuo pakartotinio įsijungimo

Jei darbo metu dingsta įtampa, ją sutvarkius, mašina

neįsijungia automatiškai. Norint vėl dirbti su mašina, reikia ją

išjungti ir vėl įjungti.

Taaskäivituskaitse

Sisselülitatud masin ei käivitu enam uuesti pärast voolukatke-

stust. Töö jätkamiseks lülitage masin välja ja seejärel taas sisse.

Защита от повторного включения

При исчезновении напряжения устройство не работает.

Для продолжения работы устройство выключите и снова

включите.

Защита от повторно пускане След спиране на

електрозахранването включената машина не започва

да работи отново. За да продължите работа изключете и

отново включете машината.

Protecţie contra repornirii

Maşina conectată nu reporneşte după o întrerupere de

curent. Pentru a putea lucra în continuare, maşina trebuie

oprită şi apoi repornită.

Заштита од повторно придвижување

Вклучената машина во случај на снемување струја не

се вклучува повторно. За да продолжите со работа

исклучете ја машината и вклучете ја повторно.

Захист від повторного запуску

Увімкнена машина не продовжує роботу після того, як

була вставлена акумуляторна батарея.















11

TIP

VII

TIP

< 30°

12

VIII

1. 2.

1.

2.



Zubehör

Accessoires

Accessorio

Acessório

Toebehoren

Tilbehør

Tillbehör

Lisälaite



Aksesuar



Príslušenstv



Tartozékokat

Oprema

Piederumi

Prieda

Tarvikud

Aksessuaarid





Accesoriu







13

I

VIII

1. 2.

3.



Zubehör

Accessoires

Accessorio

Acessório

Toebehoren

Tilbehør

Tillbehör

Lisälaite



Aksesuar



Príslušenstv



Tartozékokat

Oprema

Piederumi

Prieda

Tarvikud

Aksessuaarid





Accesoriu







14

VIII

3.

2.1.



Zubehör

Accessoires

Accessorio

Acessório

Toebehoren

Tilbehør

Tillbehör

Lisälaite



Aksesuar



Príslušenstv



Tartozékokat

Oprema

Piederumi

Prieda

Tarvikud

Aksessuaarid





Accesoriu







15

GB

English

TECHNICAL DATA

Angle Grinder

M18 CAG115X

M18 CAG125X

M18 CAG115XPD

M18 CAG125XPD

Production code 4585 08 02...

... 000001-999999

4585 04 02...

... 000001-999999

4585 16 02...

... 000001-999999

4585 12 02...

... 000001-999999

Volts 18 V 18 V 18 V 18 V

Rated speed 8500 min

-1

8500 min

-1

8500 min

-1

8500 min

-1

D= Grinding disk diameter max.

d= Grinding disk hole diameter

115 mm

22,2 mm

125 mm

22,2 mm

115 mm

22,2 mm

125 mm

22,2 mm

b= Cutting disk thickness min. / max.

1 / 3 mm 1 / 3 mm 1 / 3 mm 1 / 3 mm

b= Grinding disk thickness max. 6 mm 6 mm 6 mm 6 mm

D= Grinding surface diameter max. 115 mm 125 mm 115 mm 125 mm

D= Wiring brush diameter max. 75 mm 75 mm 75 mm 75 mm

Thread of work spindle M 14 M 14 M 14 M 14

Weight without battery 1,8 kg 1,8 kg 1,8 kg 1,8 kg

Weight according EPTA-Procedure 01/2003 (Li-lon 4,0 Ah) 2,5 kg 2,5 kg 2,5 kg 2,5 kg

Noise information

Measured values determined according to EN 60745. Typically, the A-weighted noise levels of the tool are:

Sound pressure level (Uncertainty K=3dB(A))

Sound power level (Uncertainty K=3dB(A))

Wear ear protectors!

83,7 dB(A)

94,7 dB(A)

83,2 dB(A)

94,2 dB(A)

83,7 dB(A)

94,7 dB(A)

83,2 dB(A)

94,2 dB(A)

Vibration information

Vibration total values (triaxial vector sum) determined according to EN 60745

Surface grinding:

Vibration emission value a

h,SG

Uncertainty K=

3,3 m/s

2

1,5 m/s

2

3,4 m/s

2

1,5 m/s

2

3,3 m/s

2

1,5 m/s

2

3,4 m/s

2

1,5 m/s

2

Disk sanding:

Vibration emission value a

h,DS

Uncertainty K=

1,5 m/s

2

1,5 m/s

2

1,4 m/s

2

1,5 m/s

2

1,5 m/s

2

1,5 m/s

2

1,4 m/s

2

1,5 m/s

2

For other applications, e.g. Abrasive Cutting-O Operations or Wire Brushing other vibration values could occur.

WARNING!

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745

and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main applications of the tool. However if the tool is used for dierent applications,

with dierent accessories or poorly maintained, the vibration emission may dier. This may signicantly increase the exposure level over

the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is

running but not actually doing the job. This may signicantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from the eects of vibration such as: maintain the tool and the accessories,

keep the hands warm, organisation of work patterns.

16

GB

English

WARNING!

Read all safety warnings and all instructions. Failure to

follow the warnings and instructions may result in electric shock,

re and/or serious injury.

Save all warnings and instructions for future reference.

ANGLE GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding, Wire

Brushing or Abrasive Cutting-O Operations:

a) This power tool is intended to function as a grinder,

sander, wire brush or cut-o tool. Read all safety warnings,

instructions, illustrations and specications provided with

this power tool. Failure to follow all instructions listed below may

result in electric shock, re and/or serious injury.

b) Operations such as polishing are not recommended

to be performed with this power tool.Operations for which

the power tool was not designed may create a hazard and cause

personal injury.

c) Do not use accessories which are not specically

designed and recommended by the tool manufacturer. Just

because the accessory can be attached to your power tool, it does

not assure safe operation.

d) The rated speed of the accessory must be at least equal

to the maximum speed marked on the power tool. Accesso-

ries running faster than their rated speed can break and y apart.

e) The outside diameter and the thickness of your

accessory must be within the capacity rating of your power

tool. Incorrectly sized accessories cannot be adequately guarded

or controlled.

f) Threaded mounting of accessories must match the grin-

der spindle thread. For accessories mounted by anges, the

arbour hole of the accessory must t the locating diameter

of the ange. Accessories that do not match the mounting hard-

ware of the power tool will run out of balance, vibrate excessively

and may cause loss of control.

g) Do not use a damaged accessory. Before each use inspect

the accessory such as abrasive wheels for chips and cracks,

backing pad for cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or accessory is dropped,

inspect for damage or install an undamaged accessory. After

inspecting and installing an accessory, position yourself and

bystanders away from the plane of the rotating accessory

and run the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break apart during this

test time.

h) Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing protectors, gloves

and shop apron capable of stopping small abrasive or

workpiece fragments. The eye protection must be capable of

stopping ying debris generated by various operations. The dust

mask or respirator must be capable of ltrating particles generated

by your operation. Prolonged exposure to high intensity noise may

cause hearing loss.

i) Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal protec-

tive equipment. Fragments of workpiece or of a broken accessory

may y away and cause injury beyond immediate area of operation.

j) Hold the power tool by insulated gripping surfaces only,

when performing an operation where the cutting accessory

may contact hidden wiring. Cutting accessory contacting a “live”

wire may make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

k) Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may grab the

surface and pull the power tool out of your control.

l) Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag your

clothing, pulling the accessory into your body.

m) Regularly clean the power tool’s air vents. The motor’s fan

will draw the dust inside the housing and excessive accumulation of

powdered metal may cause electrical hazards.

n) Do not operate the power tool near ammable materials.

Sparks could ignite these materials.

o) Do not use accessories that require liquid coolants. Using

water or other liquid coolants may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating

wheel, backing pad, brush or any other accessory. Pinching or snag-

ging causes rapid stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch

point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels may also break

under these conditions.

Kickback is the result of power tool misuse and/or incorrect opera-

ting procedures or conditions and can be avoided by taking proper

precautions as given below.

a) Maintain a rm grip on the power tool and position your

body and arm to allow you to resist kickback forces. Always

use auxiliary handle, if provided, for maximum control over

kickback or torque reaction during start-up. The operator can

control torque reactions or kickback forces, if proper precautions

are taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in the area where power tool

will move if kickback occurs. Kickback will propel the tool

in direction opposite to the wheel’s movement at the point of

snagging.

d) Use special care when working corners, sharp edges etc.

Avoid bouncing and snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade or toothed

saw blade. Such blades create frequent kickback and loss of control.

Safety Warnings Specic for Grinding and Abrasive Cutting-

O Operations:

a) Use only wheel types that are recommended for your

power tool and the specic guard designed for the selected

wheel. Wheels for which the power tool was not designed cannot

be adequately guarded and are unsafe.

17

GB

English

b) The grinding surface of the centre depressed wheels must

be mounted below the plane of the guard lip. An improperly

mounted wheel that projects through the plane of the guard lip

cannot be adequately protected.

c) The guard must be securely attached to the power tool

and positioned for maximum safety, so the least amount

of wheel is exposed towards the operator. The guard helps

to protect the operator from broken wheel fragments, accidental

contact with wheel and sparks that could ignite clothing.

d) Wheels must be used only for recommended applications.

For example: do not grind with the side of cut-o wheel.

Abrasive cut-o wheels are intended for peripheral grinding, side

forces applied to these wheels may cause them to shatter.

e) Always use undamaged wheel anges that are of correct

size and shape for your selected wheel. Proper wheel anges

support the wheel thus reducing the possibility of wheel breakage.

Flanges for cut-o wheels may be dierent from grinding wheel

anges.

f) Do not use worn down wheels from larger power tools.

Wheel intended for larger power tool is not suitable for the higher

speed of a smaller tool and may burst.

Additional Safety Warnings Specic for Abrasive Cutting-O

Operations:

a) Do not “jam” the cut-o wheel or apply excessive pressure.

Do not attempt to make an excessive depth of cut. Overstressing

the wheel increases the loading and susceptibility to twisting or

binding of the wheel in the cut and the possibility of kickback or wheel

breakage.

b) Do not position your body in line with and behind the

rotating wheel. When the wheel, at the point of operation, is moving

away from your body, the possible kickback may propel the spinning

wheel and the power tool directly at you.

c) When wheel is binding or when interrupting a cut for any

reason, switch o the power tool and hold the power tool

motionless until the wheel comes to a complete stop. Never

attempt to remove the cut-o wheel from the cut while the

wheel is in motion otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause of wheel binding.

d) Do not restart the cutting operation in the workpiece. Let

the wheel reach full speed and carefully re-enter the cut. The

wheel may bind, walk up or kickback if the power tool is restarted in

the workpiece.

e) Support panels or any oversized workpiece to minimize the

risk of wheel pinching and kickback. Large workpieces tend to sag

under their own weight. Supports must be placed under the workpiece

near the line of cut and near the edge of the workpiece on both sides

of the wheel.

f) Use extra caution when making a “pocket cut” into existing

walls or other blind areas. The protruding wheel may cut gas or

water pipes, electrical wiring or objects that can cause kickback.

Safety Warnings Specic for Sanding Operations:

a) Do not use excessively oversized sanding disc paper.

Follow manufacturers recommendations, when selecting

sanding paper. Larger sanding paper extending beyond the

sanding pad presents a laceration hazard and may cause snagging,

tearing of the disc or kickback.

Safety Warnings Specic for Wire Brushing Operations:

a) Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress the wires

by applying excessive load to the brush. The wire bristles can

easily penetrate light clothing and/or skin.

b) If the use of a guard is recommended for wire brushing,

do not allow any interference of the wire wheel or brush

with the guard. Wire wheel or brush may expand in diameter due

to work load and centrifugal forces.

Additional Safety and Working Instructions

When grinding metal, ying sparks are produced. Take care that

no persons are endangered. Because of the danger of re, no

combustible materials should be located in the vicinity (spark ight

zone). Do not use dust extraction.

Avoid ying sparks and sanding dust hit your body.

Never reach into the danger area of the machine when it is running.

Immediately switch o the machine in case of considerable vibra-

tions or if other malfunctions occur. Check the machine in order to

nd out the cause.

Under extreme conditions (e.g. smooth-grinding metals with

the arbour and vulcanized bre grinding disk), signicant

contamination can build up on the inside of the angle grinder. For

safety reasons, in such conditions a ground fault interrupter must

be connected in series. If the ground fault interrupter trips the

machine must be sent for service.

Chips and splinters must not be removed while the machine is

running.

WARNING! To reduce the risk of re, personal injury, and product

damage due to a short circuit, never immerse your tool, battery

pack or charger in uid or al-low a uid to ow inside them.

Corrosive or conductive uids, such as seawater, certain industrial

chemicals, and bleach or bleach containing products, etc., Can

cause a short circuit.

Use only System M18 chargers for charging System M18 battery

packs. Do not use battery packs from other systems.

Never break open battery packs and chargers and store only in dry

rooms. Keep dry at all times.

SPECIFIED CONDITIONS OF USE

The angle grinder is intended for grinding and cutting metal, stone

and ceramicmaterials as well as sanding and wire brushing.

Use the cutting guard from the accessories range for cutting

application.

Please refer to the instructions supplied by the accessory

manufacturer.

The machine is suitable only for working without water.

18

GB

English

WORKING INSTRUCTIONS

For accessories intended to be tted with threaded hole wheel,

ensure that the thread in the wheel is long enough to accept the

spindle length.

Always use and store the cutting and grinding disks according to

the manufacturer‘s instructions.

Always use the correct guard for cutting and grinding.

The grinding surface of the centre depressed disks must be moun-

ted min. 2 mm below the plane of the guard lip.

The adjusting nut must be tightened before starting to work with

the machine.

Always use the auxiliary handle.

The workpiece must be xed if it is not heavy enough to be steady.

Never move the workpiece towards the rotating disk by hand.

ELECTRONICS

The built-in electronic will keep a constant speed even under

increased load.

In case of overload, the rotational speed is being reduced until

machine stops.

The machine has an overload and anti-kickback safety function and

stops if it is overloaded.

Please note that the machine will automatically accelerate back to

its original operating speed if the load is removed from it.

After it has reached its operating speed the machine is ready for

use again.

RESTART CUTOUT

A zero-voltage switch prevents the machine from restarting after a

power cut (Battery change).

When resuming work, switch the machine o and then switch it

back on again.

SMOOTH START

Electronic smooth start for save use prevents jerky run-up of the

machine.

BATTERIES

Battery packs which have not been used for some time should be

recharged before use.

Temperatures in excess of 50°C (122°F) reduce the performance of

the battery pack. Avoid extended exposure to heat or sunshine (risk

of overheating).

The contacts of chargers and battery packs must be kept clean.

For an optimum life-time, the battery packs have to be fully

charged, after use.

To obtain the longest possible battery life remove the battery pack

from the charger once it is fully charged.

For battery pack storage longer than 30 days: Store the battery

pack where the temperature is below 27°C and away from moisture

Store the battery packs in a 30% - 50% charged condition Every six

months of storage, charge the pack as normal.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods Legisla-

tion requirements.

Transportation of those batteries has to be done in accordance with

local, national and international provisions and regulations.

The user can transport the batteries by road without further

requirements.

Commercial transport of Lithium-Ion batteries by third parties is

subject to Dangerous Goods regulations. Transport preparation and

transport are exclusively to be carried out by appropriately trained

persons and the process has to be accompanied by corresponding

experts.

When transporting batteries:

Ensure that battery contact terminals are protected and insulated

to prevent short circuit. Ensure that battery pack is secured against

movement within packaging. Do not transport batteries that are

cracked or leak. Check with forwarding company for further advice

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times.

Use only Milwaukee accessories and Milwaukee spare parts. Should

components need to be replaced which have not been described, please

contact one of our Milwaukee service agents (see our list of guarantee/

service addresses).

If needed, an exploded view of the tool can be ordered. Please state

the Article No. as well as the machine type printed on the label

and order the drawing at your local service agents or directly at:

Techtronic Industries GmbH, Max-Eyth-Straße10, 71364Winnen-

den, Germany.

ECDECLARATION OF CONFORMITY

We declare under our sole responsibility that the product described

under “Technical Data” fullls all the relevant provisions of the

directives

2011/65/EU (RoHS)

2006/42/EC

2014/30/EU

and the following harmonized standards have been used.

EN 60745-1:2009 + A11:2010

EN 60745-2-3:2011 + A2:2013 + A11:2014

EN 55014-1:2006 + A1:2009 + A2:2011

EN 55014-2:2015

EN 50581:2012

Winnenden, 2017-11-30

Alexander Krug / Managing Director

Authorized to compile the technical le

Techtronic Industries GmbH

Max-Eyth-Straße 10, 71364 Winnenden, Germany

Leht laadib ...

Milwaukee M18 CAG125X Original Instructions Manual

See käsiraamat sobib ka

Milwaukee M18 CAG125X Original Instructions Manual

teistes keeltes

Seotud paberid

Muud dokumendid