POINT PRO POSDH8020 AVFUKTER Omaniku manuaal

Dehumidiﬁer

POSDH8020

User Manual

With Wi-Fi Control

Thank you for purchasing your new POINT PRO Series Dehumidiﬁer.

Takk for at du kjøpte din nye POINT PRO Series Avfukter.

Kiitos, kun ostit uuden POINT PRO -sarjan ilmankuivaajan.

Tak fordi du købte din nye POINT PRO Series Augter.

Tack för att du köpte din nya POINT PRO-serie Avfuktare.

4 - 22

23 - 41

42 - 60

61 - 79

80 - 98

IMPORTANT SAFEGUARDS

● Disconnect the appliance from its power source during service and

when replacing parts and cleaning.

●Check the nameplate for the type of refrigerant gas

used in your appliance.

●Speciﬁc information regarding appliances with refrigerant gas.

The applianceis recommended not to pierce the cooling circuit of the

machine. At the end of its useful life, deliver the appliance to a

special waste collection centre for disposal.

GWP(Global Warming Potential): R410A: 2088, R134a: 1430, R290: 3,

R32: 675.

●This hermetically sealed system contains ﬂuoridated greenhouse

gases.

●ENVIRONMENTAL INFORMATION: This unit contains ﬂuoridated

greenhouse gases covered by the Kyoto Protocol.

● Do not use this unit for functions other than those described in this

instruction manual.

● Make sure the plug is plugged ﬁrmly and completely inserted into the

mains power outlet. It can result in the risk of electric shock or ﬁre.

● Do not plug other appliances into the same outlet, it can result in the

risk of electric shock.

● Do not disassemble or modify the appliance or the mains power cable,

it can result in the risk of electric shock or ﬁre. All other services

should be referred to a qualiﬁed technician.

● Do not place the mains power cable or appliance near a heater,

radiator, or other heat source. It can result in the risk of electric shock

or ﬁre.

● This unit is equipped with a mains power cable that has a earthed

wire connected to an earthed pin or grounding tab. The plug must be

plugged into a mains power socket that is properly installed and

earthed. Do not under any circumstances cut or remove the earthed

pin or grounding tab from this plug.

● The unit should be used or store in such a way that it is protected

from moisture e.g. condensation, splashed water, etc. Unplug the

unit immediately if this occurs.

4

● Always transport your appliance in a vertical position and place on

a stable, level surface during use. If the unit is transported laying on

its side it should be stood up and left unplugged for 6 hours.

● Always use the switch on the control panel or remote controllerto

turn the unit o, and do not start or stop operation by plugging in or

unplugging the mains power cable. It can result in the risk of electric

shock.

●Do not touch the buttons on the control panel with your wet and

damp ﬁngers.

● Do not use hazardous chemicals to clean or come into contact with

the unit. To prevent damage to the surface ﬁnish, use only a soft

cloth to clean the appliance. Do not use wax, thinner, or a strong

detergent. Do not use the unit in the presence of inﬂammable

substance or vapour such as alcohol, insecticides, gasoline, etc.

● If the appliance is making unusual sounds or is emitting smoke or

an unusual odor, unplug it immediately.

● Do not clean the unit with water. Water can enter the unit and

damage the insulation, creating a shock hazard. If water enters the

unit, unplug it immediately and contact Customer Service.

● Utilize two or more people to lift and install the unit.

● Always grasp the plug when plugging in or unplugging the appliance.

Never unplug by pulling on the cord. It can result in the risk of

electrical shock and damage.

● Install the appliance on a sturdy, level ﬂoor capable of supporting up

to 110lbs (50kg). Installation on a weak or unlevel ﬂoor can result in

the risk of property damage and personal injury.

● The applianceis compliant with the REDirective(2014/53/EU).

If the appliance have the Wi-Fi function, the transmission power:

less than 20dBm, and the radio frequency range is: 2412MHz-2472MHz.

5

According the EN standard:

● This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and

understand the hazards involved.

● Children shall not play with the appliance.

● Cleaning and user maintenance shall not be made by children without

 supervision.

● If the mains power cable is damaged, it must be replaced by the

manufacturer, its service agent or a similarly qualiﬁed person in order

to avoid a hazard.

● The appliance shall be installed in accordance with national wiring

regulations.

● When the fuse is blown/circuit breaker is tripped, check the house

fuse/circuit breaker box and replace fuse or reset breaker

●Details of type and rating of fuses: T; 3.15A; 250VAC.

6

IMPORTANT - GROUNDING METHOD

This product is factory equipped with a power supply cord mains power

cable that has a three-pronged grounded plug. It must be plugged into

a mating grounding type receptacle in accordance with the National

Electrical Code and applicable local codes and ordinances. If the circuit

does not have a grounding type receptacle, it is the responsibility and

obligation of the customer to exchange the existing receptacle in

accordance with the National Electrical Code and applicable local codes

and ordinances. The third ground prong should not, under any

circumstances, be cut or removed. Never use the cord mains power

cable, the plug or the appliance when they show any sign of damage.

Do not use your appliance with an extension cord unless it has been

checked and tested by a qualiﬁed electrical supplier. Improper

connection of the grounding plug can result in risk of ﬁre, electric shock

and/or injury to persons associated with the appliance. Check with a

qualiﬁed service representative if in doubt that the appliance is properly

grounded.

ELECTRICAL CONNECTIONS

Before plugging the appliance into the mains socket, check that:

● The mains power supply corresponds to the value indicated on the

rating plate on the back of the appliance.

● The power socket and electrical circuit are adequate for the appliance.

● The mains socket matches the plug. If this is not the case, have the

plug replaced.

● The mains socket is adequately earthed. Failure to follow these

important safety instructions absolves the manufacturer of all

liability.

7

SOME NOTIONS ON HUMIDITY

Air always contains a certain amount of water in the form of vapour.

This determines the level of humidity in an atmosphere. The capacity

of the air to hold water vapour increases with temperature. This is why

in our homes, as soon as the temperature decreases, the vapour

contained in the air condenses, as is evident on the colder surfaces in

the room, such as the windows, walls etc. The purpose of a dehumidiﬁer

is to remove the excess moisture from the air, avoiding the damage

caused by condensation

Experts have established that the optimum environmental conditions

for our well being and for the home are obtained between 40% and 60%

relative humidity. With very low temperatures, you are recommended

to heat the room even minimally. This considerably increases the

dehumidifying power of the appliance. With heating, the condensation

formed by the water vapour on windows and other cold surfaces

evaporates into the air to be collected by the dehumidiﬁer. Air leaving

the dehumidiﬁer is usually about 1℃-2℃warmer than room

temperature..

8

Preparation

1

2

3

4

5

6

7

8

1.Control panel

2.Air outlet

3. Tank

4. Water level view window

5. Handle

6. Air intake grille

7.Mains power cable

8. Drain pipe

Note: All the illustrations in this manual are for explanatory purposes only.

your appliance may be slightly dierent.

Before use,remove the accessory from the tank

- Remove the tank from appliance.

- Take out of the the plug, and other accessories.

- Correctly put back the tank into the appliance.

Component Description

9

Identiﬁcation of parts

The accessories are:

(Note:If an accessory is not in the tank, you will ﬁnd it elsewhere in the

packaging.)

Chip of tank

Drainpipe

1 set

Installation

Take out the mains power cable from tank.

Take out the tank, remove the mains power cable and accessories from it.

Install the chip on the tank.

10

CONTROL PANEL

1

2

3

4

5

6

A B C D E F

1. Timer symbol

2. Wi-Fi symbol

3. Tank full symbol

4. Drysymbol

5. Fan symbol

6. Laundry symbol

A. Timer button

B. Swing button

C. Decrease button

D. Increase button

E. Mode button

F. ON / OFF button

"  " button

- On / o power supply, used to control the start-up or shut down the appliance.



Decrease / Increase button

 - Press "  " / "  " to select the indoor humidity level you expect to

achieve, or set the time.

"  " button:

Press the " " button to turn onthe appliance, and press the " " button

to choose dierent mode.

●

Dehumidifying mode

Press the " MODE " button until the " DRY " symbol illuminates.

- Press the "  " or " " to choose the humidity desired, humidity adjustable

range is 35%RH-80%RH. The screen will display the setting humidity, and

after few seconds, turn to display the ambient humidity.

- When the ambient humidity lower than setting humidity, the compressor

stop running, and after few minutes the fan stop running.

●

11

Continuous mode

Under dehumidify mode, Press the "  " button until the " " indicator

illuminates, then the unit will continuously run.

●

Fan mode(Only apply to the unit with Fan function )

When the appliance is running, press the "  " button until the “Fan" symbol

illuminates.

 You can startup or shutdown the fan functionby pressing the "  " button

The screen display below:

.

●

In this function, the compressor is not work, and appliance is not dehumidify.

Laundry mode

Press the "  " button until the " LAUNDRY " symbol illuminates.

 In this mode humidity can not be adjusted, and screen display ambient

humidity.

 After run 24 hours, the appliance is quit laundry mode, turn to dehumidifying

mode and set humidity 60%RH.

●

Dehumidifying + Fanmode

Press the " " button until the " DRY " and “Fan”symbols both illuminates.

In this mode the humidity can be set like dehumidifying mode, and when

the ambient humidity is lower than setting, the fan will running continuous.

●

“ ” button

Press the "  " button to control the angle of the inner deﬂector .

●

“ ” button

This timer can be used to delay the appliance start-up or shutdown, this

avoids wasting electricity by optimizing operating periods.

●

12

Programming start up



Turn on the appliance, choose the mode you want, for example Dehumidify

mode. Turn o the appliance.

Press the "  " button, the”Timer ”symbolstarts to ﬂash, press the

" " / " " to adjust the set timefrom 0.5-24 hours.

In 5 seconds without the operation, the timer start function.

Press the "  " button again to cancel the Timer.

●

Programming shut down

When the appliance is running, press the button. the "  " symbolstarts

to ﬂash, press the " " / " " to adjust the set timefrom 0.5-24 hours.

 In 5 seconds without the operation, the timer start function.

Press the "  " button again to cancel the Timer.

●

Alarm of Tank full

- When tank is full, the compressor and fan will shut o, "TANK FULL"

symbolis ﬂashing, after about 3 minutes make a beeping noise, and after

about 6 minutes make a beeping noise again.

- The unit will not run again until the tank is emptied and properly placed

back inside the unit.

- The tank should be cleaned every week to prevent the growth of mold,

mildew and bacteria. Use a mild detergent to clean. Once clean, completely

dry the tank and place it back inside unit.

13

Note: Hold the tank with both hands when emptying.

Note: When the tank is full or removed from the unit, the compressor will

turn o but the fan will continue to run for a few minutes. This is

completely normal. The unit will not be removing moisture from the air

at this time.

Note: During operation, it is normal for the unit to exhaust warm air from the

top of the unit.

Caution: Do not place the tank on the ﬂoor when it is full as it is uneven on

the bottom and water may spill.

Continuous drain

Connect the drain pipe on the holeof unit, then the unit can continuous run

without clean the tank.

1) Put the unit on level ﬂoor, take out the tank, remove the chip of tank;

2) Install thepipeon drain nozzle ;

3) Put back the tank correctly and make the drain pipe on gap of tank,

don’t press the pipe ;

4) Press " " button to run the unit.

Note: If no need the function of continuous drain, remove the drain

pipe and put back the tank in unit correctly, then the water will ﬂow

into tank.

14

Note: Install the drain pipe follow below picture.

 Install the drain pipe correctly, or the water cannot drain from the pipe.

Notice: If the unit is placed on un-level ground or the drain pipe, the water will

full the tank and stop run. 

If is not correctly installed check that the unit is placed on ﬂat ground

and that the drain pipe is installed correctly.

AUTOMATIC DEFROST

When frost builds up on the evaporator coils, the compressor will stopand the

fan will continue to run until thefrost disappears. When the coils are

completely defrosted, the compressor willautomatically restart and

dehumidifywill resume.

Location requirements:

The unit operating in a basement will have little no eect in drying out an

adjacent enclosed storage area, such as a closet, unless there is adequate

circulation of air in and out of the area.

1.Do not use outdoors.

2. This applianceis intended for indoor use only.

Place the appliance on a smooth, level ﬂoor s

urface that is strong enough to support the

unitwith a full tank of water.

3.Allow at least 18”(45cm)of around and above

space away from the wall for ecient working.

4.Placethe appliancein an area where the

temperature will not fall5℃(41℉).

15

5. Use the dehumidiﬁer in cooking, laundry, bathing and dish-washing

areasthat have excessive moisture.

6.Place the dehumidiﬁer away from a clothes dryer.

7. Use the dehumidiﬁer in a basement to help prevent moisture damage.

8.The dehumidiﬁer must be operated in an enclosed area to be most

 eective,close all doors, windows and other outside openings to the room.

9.Do not block the air inlet or outlet of the appliance.

Reduced air ﬂow will result in poor performance and could damage the unit.

CLEAN AND MAINTENANCE

Before cleaning or maintenance, turn the appliance o by pressing the

“POWER” button on the control panel, wait for a few minutes then unplug

from the mains socket.



CLEANING THE CABINET

You should clean the appliance with a slightly damp cloth then dry with a dry

cloth.

Never wash the appliance with water, it could be dangerous.

Never use petrol, alcohol or solvents to clean the appliance.

Never spray insecticide liquids or similar.

●

CLEANING THE FILTER



To keep your appliance working eciently,you should clean the ﬁlter every

week of operation.

Follow the diagram to remove the ﬁlter.



To avoid possible cuts, avoid contacting the metal parts

of the appliance when removing or re-installing the ﬁlter.

 It can result in the risk of personal injury.



Use a vacuum cleaner to remove dust accumulations

 from the ﬁlter. If it is very dirty, immerse in warm water

and rinse a number of times. The water should never

be hotter than 40℃(104℉). After washing, leave the

ﬁlter to dry then attach the intake grille to the appliance.

●

16

Health ﬁlter

Some model have the health ﬁlter, follow the diagrams below to remove it .

clean the ﬁlter every three month.

Use the vacuum to clean it. After cleaning the ﬁlter , install the ﬁlter before

use the appliance.

END OF SEASON OPERATIONS

- Unplug from the mains socket,empty thetank,remove the cap.

- Run o all water left inside the appliance. When all the water has been

drained,put the cap back in place.

- Clean the ﬁlter and dry thoroughly before putting back.

- Cover the appliance prevent from dust.

- Store the appliance upright in a dry location.

STARTOF SEASON CHECKS

Make sure the mains power cable and plug are undamaged and theearth

system is ecient.

Follow the installation instructions precisely.

17

TROUBLESHOOTING

Occasionally,you may encounter some problems that are of a minor nature a

nd a service call may not be necessary. Use this troubleshooting guide to

identify possible problems you may be experiencing

Problem Possible Causes Solutions

The dehumidiﬁer is

unplugged.

Make sure the dehumidiﬁer's

plug is pushedcompletely into

the outlet.

Dehumidiﬁer has reached

its present level or the

tank is full.

The dehumidiﬁer automatically

turns o wheneither condition

occurs. Change to a lower

setting or empty the water

tank and replace properly.

Tank is not in the proper

position.

The tank must be in place

and securelyseated for the

dehumidiﬁer to operate.

Power Failure.

There is a protective time delay

(up to 3 min.)to prevent trip-

ping of the compressor

overload.For this reason, the

unit may notstart normal

dehumidifyfor 3 minafterit is

powered back on.

Not enough time allowed

for unit to remove

moisture.

When ﬁrst installed,allow at

least 24 hours to maintain the

desired dryness.

Dehumidiﬁer

doesnot

start

The fuse is blown/circuit

breaker is tripped.

Check the house fuse/circuit

breaker boxand replace fuse

or reset breaker.

Airﬂow is restricted.

Make sure there are no

curtains, blinds, orfurniture

blocking the front or back of

thedehumidiﬁer. See the

CHOOSING ALOCATION

section.

Dehumidiﬁer

does not dry

the air as it

should

18

Problem Possible Causes Solutions

Dirty ﬁlter. See the CLEAN FILTER section.

The Humidity Control may

not be set low enough.

For drier air, press the button

to lowerthe percent humidity

desired in the room,orset the

dehumidiﬁer to  for

maximumdehumidify.

Doors and windows may

not be closed tightly.

Check that all doors, windows,

and otheropenings are

securely closed.

Clothes dryer may be

blowing moist air into the

room.

Install the dehumidiﬁer away

from the dryer.

The dryer should be vented

outside.

Room temperature is too

low.

Moisture removal is best at

higher roomtemperatures.

Lower room temperatures will

reduce the moisture removal

rate. This modelis designed to

operate at temperatures above

5℃(41℉).

Dehumidiﬁer

does not dry

the air as it

should

The area is too large

The capacity of the appliance

can not meet the area of the

room

Doors and windows are

open

Close the door and window

Appliance runs

too long

Appliance run recently or

the room temperature is

too low

It is normal, frost usually

disappear in 60 min

Frost appears

on heat-

exchanger

The air is passing through

the appliance

This is normal

Fan noise

The drain connection may

be agingor loose

Check the drain connection and

the appliance is placed level

The drain pipe is

connected, but the water

is not drained.

If use the tank, remove the

drain pipe and put back the

drain cover; or install the drain

pipe correctly

Water on the

ﬂoor

19

If the following error code appears, contact the after-sales service department

for inspection and repair.

CODE DESCRIPTION

EH

E2

Humidity sensor failure

Temperature sensor failure

Strictest operation environment: 5℃~32℃（41℉~90℉）,30%RH~90%RH. 

20

Leht laadib ...

POINT PRO POSDH8020 AVFUKTER Omaniku manuaal

POINT PRO POSDH8020 AVFUKTER Omaniku manuaal

teistes keeltes

Seotud paberid

Muud dokumendid