Worx WX014 Kasutusjuhend

WG329E WG329E.5 WG329E.9

EN

DK

FIN

NOR

SV

Cordless Limbing and Trimming Chain Saw

Mai ledningsfri kædesav til kvistning og trimning

Akkukäyttöinen oksa- ja trimmausmoottorisaha

Trådløs motorsag for beskjæring og trimming

Sladdlös kedjemotorsåg för grenkapning och trimning

P09

P23

P37

P51

P65

Original instructions EN

Original brugsanvisning DK

Alkuperäiset ohjeet FIN

Original driftsinstruks NOR

Bruksanvisning i original SV

6

4

5

3

2

1

14

19

17 18

7

8

9

10

11

12

16

15

100mm

13

9

10

DC

B3B2

B1A

3mm

a

aback

b

c

ffront

8

7

e

d

17

IH

G2G1

FE

g

II

I

II

O1N

ML

KJ

I

II

11/3

2

2/3

11/3

2

2/3

SR

Q2Q1

PO2

Z

Y

kg

Z

Y

h

i

YX

WV

UT

9

Cordless Limbing and Trimming Chain Saw

EN

1. REAR HANDLE

2. TRIGGER SWITCH

3. LOCK OUT BUTTON

4. FRONT HANDLE

5. MOTOR

6. JAW TEETH

7. GUIDE BAR

8. SAW CHAIN

9. CHAIN ACCESS COVER

10. CHAIN ACCESS COVER NUT

11. AUXILIARY POSITION

12. LOCK PIN

13. LOCK PIN RECEPTACLE (See Fig. B3)

14. BATTERY PACK *

15. OIL LEVEL WINDOW

16. OIL FILLER

17. SPROCKET

18. CHAIN TENSIONING BOLT

19. OIL BOTTLE

* Not all the accessories illustrated or described are included in standard delivery.

10

Cordless Limbing and Trimming Chain Saw

EN

TECHNICAL DATA

Type WG329E WG329E.5 WG329E.9 (3- designation of machinery, representative of

Jaw Saw)

WG329E WG329E.5 WG329E.9

Voltage 20V Max*

No load speed 1350/min

Guide bar length 6” (150 mm)

Oil tank capacity 30 ml

Chain pitch 1/4’’ (6.4 mm)

Chain gauge 0.05’’ (1.3 mm)

Chain speed 2.54 m/s

Number of chain links 42

Charging time 5hr approx. 1hr approx. /

Weight 3.6kg 3.2kg

* Voltage measured without workload. Initial battery voltage reaches maximum of 20 volts.

Nominal voltage is 18 volts.

NOISE AND VIBRATION DATA

A weighted sound pressure LpA = 72,2dB(A)

A weighted sound power LwA = 82dB(A)

KpA&KwA 3.0dB(A)

Wear ear protection when sound pressure is over 80dB(A)

Vibration total values (triax vector sum) determined according to EN 60745:

Vibration emission value ah = 0,52m/s² ah1 = 0,46m/s²

Uncertainty K=1.5 m/s2

The declared vibration total value may be used for comparing one tool with another, and may

also be used in a preliminary assessment of exposure.

WARNING: The vibration emission value during actual use of the power tool can differ

from the declared value depending on the ways in which the tool is used dependant on the

following examples and other variations on how the tool is used:

How the tool is used and the materials being cut or drilled.

11

Cordless Limbing and Trimming Chain Saw

EN

The tool being in good condition and well maintained

Using the correct accessory for the tool and ensuring it is sharp and in good condition.

The tightness of the grip on the handles and if any anti vibration accessories are used.

And the tool is being used as intended by its design and these instructions.

This tool may cause hand-arm vibration syndrome if its use is not adequately managed.

WARNING: To be accurate, an estimation of exposure level in the actual conditions of use

should also take account of all parts of the operating cycle such as the times when the tool

is switched off and when it is running idle but not actually doing the job. This may signiﬁcantly

reduce the exposure level over the total working period.

Helping to minimize your vibration exposure risk.

ALWAYS use sharp chisels, drills and blades

Maintain this tool in accordance with these instructions and keep well lubricated (where

appropriate)

If the tool is to be used regularly then invest in anti vibration accessories.

Plan your work schedule to spread any high vibration tool use across a number of days.

ACCESSORIES

WG329E WG329E.5 WG329E.9

Wrench 1

Oil Bottle 1

Chain oil (100ml) 1

Charger 1 (WA3760) 1 (WA3860) /

Battery (WA3551.1) 1 1 /

We recommend that you purchase your accessories from the same store that sold you the tool.

Use good quality chain oil. Use only replacement bar and chain of the same speciﬁcation. Your

retailer can advise the correct purchase.

12

Cordless Limbing and Trimming Chain Saw

EN

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING: Read all safety

warnings and all instructions.

Failure to follow the warnings and instructions

may result in electric shock, ﬁre and/or serious

injury.

Save all warnings and instructions for

future reference.

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in

explosive atmospheres, such as in

the presence of ﬂammable liquids,

gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders

away while operating a power tool.

Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the

outlet. Never modify the plug in any

way. Do not use any adapter plugs

with earthed (grounded) power tools.

Unmodiﬁed plugs and matching outlets

will reduce risk of electric shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock

if your body is earthed or grounded.

c) Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use

the cord for carrying, pulling or

unplugging the power tool. Keep cord

away from heat, oil, sharp edges or

moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool

outdoors, use an extension cord

suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of

electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected

supply. Use of an RCD reduces the risk of

electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are

doing and use common sense when

operating a power tool. Do not use

a power tool while you are tired or

under the inﬂuence of drugs, alcohol

or medication. A moment of inattention

while operating power tools may result in

serious personal injury.

b) Use personal protective equipment.

Always wear eye protection.

Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position

before connecting to power source

and/or battery pack, picking up or

carrying the tool. Carrying power

tools with your ﬁnger on the switch or

energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating

part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your

hair, clothing and gloves away from

moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

g) If devices are provided for the

connection of dust extraction and

collection facilities, ensure these are

connected and properly used. Use of

dust collection can reduce dust-related

hazards.

13

Cordless Limbing and Trimming Chain Saw

EN

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use

the correct power tool for your

application. The correct power tool will

do the job better and safer at the rate for

which it was designed.

b) Do not use the power tool if the

switch does not turn it on and off.

Any power tool that cannot be controlled

with the switch is dangerous and must be

repaired.

c) Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories,

or storing power tools. Such preventive

safety measures reduce the risk of starting

the power tool accidentally.

d) Store idle power tools out of the

reach of children and do not allow

persons unfamiliar with the power

tool or these instructions to operate

the power tool. Power tools are

dangerous in the hands of untrained

users.

e) Maintain power tools. Check for

misalignment or binding of moving

parts, breakage of parts and any

other condition that may affect the

power tool’s operation. If damaged,

have the power tool repaired before

use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to bind

and are easier to control.

g) Use the power tool, accessories

and tool bits etc. in accordance

with these instructions, taking into

account the working conditions and

the work to be performed. Use of the

power tool for operations different from

those intended could result in a hazardous

situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger

speciﬁed by the manufacturer. A

charger that is suitable for one type of

battery pack may create a risk of ﬁre when

used with another battery pack.

b) Use power tools only with speciﬁcally

designated battery packs. Use of any

other battery packs may create a risk of

injury and ﬁre.

c) When battery pack is not in use, keep

it away from other metal objects, like

paper clips, coins, keys, nails, screws

or other small metal objects, that can

make a connection from one terminal

to another. Shorting the battery terminals

together may cause burns or a ﬁre.

d) Under abusive conditions, liquid

may be ejected from the battery;

avoid contact. If contact accidentally

occurs, ﬂush with water. If liquid

contacts eyes, additionally seek

medical help. Liquid ejected from the

battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by

a qualiﬁed repair person using only

identical replacement parts. This will

ensure that the safety of the power tool is

maintained.

JAW SAW SAFETY

WARNINGS

1. Keep all parts of the body away from

the saw chain when the jaw saw is

operating. Before you start the jaw

saw, make sure the saw chain is not

contacting anything. A moment of

inattention while operating jaw saws may

cause entanglement of your clothing or

body with the saw chain.

2. Always hold the jaw saw with your

right hand on the rear handle and

your left hand on the front handle.

Holding the jaw saw with a reversed

hand conﬁguration increases the risk of

personal injury and should never be done.

3. Wear safety glasses and hearing

protection. Further protective

equipment for head, hands, legs

and feet is recommended. Adequate

14

Cordless Limbing and Trimming Chain Saw

EN

protective clothing will reduce personal

injury by ﬂying debris or accidental

contact with the saw chain.

4. Do not operate a jaw saw in a tree.

Operation of a jaw saw while up in a tree

may result in personal injury.

5. Always keep proper footing and

operate the jaw saw only when

standing on ﬁxed, secure and level

surface. Slippery or unstable surfaces

such as ladders may cause a loss of

balance or control of the jaw saw.

6. When cutting a limb that is under

tension be alert for spring back. When

the tension in the wood ﬁbres is released

the spring loaded limb may strike the

operator and/or throw the jaw saw out of

control.

7. Use extreme caution when cutting

brush and saplings. The slender

material may catch the saw chain and

be whipped toward you or pull you off

balance.

8. Follow instructions for lubricating,

chain tensioning and changing

accessories. Improperly tensioned

or lubricated chain may either break or

increase the chance for kickback.

9. Keep handles dry, clean, and free

from oil and grease. Greasy, oily

handles are slippery causing loss of

control.

10.Cut wood only. Do not use jaw

saw for purposes not intended. For

example: do not use jaw saw for

cutting plastic, masonry or non-wood

building materials. Use of the jaw saw

for operations different than intended

could result in a hazardous situation.

11. Hold the power tool by insulated

gripping surfaces only, because the

saw chain may contact hidden wiring.

Saw chains contacting a “live” wire may

make exposed metal parts of the power

tool “live” and could give the operator an

electric shock.

SAFETY WARNINGS FOR

BATTERY PACK

a) Do not dismantle, open or shred cells

or battery pack.

b) Do not short-circuit a battery

pack. Do not store battery packs

haphazardly in a box or drawer where

they may short-circuit each other

or be short-circuited by conductive

materials. When battery pack is not

in use, keep it away from other metal

objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that

can make a connection from one terminal

to another. Shorting the battery terminals

together may cause burns or a ﬁre.

c) Do not expose battery pack to

heat or ﬁre. Avoid storage in direct

sunlight.

d) Do not subject battery pack to

mechanical shock.

e) In the event of battery leaking, do not

allow the liquid to come into contact

with the skin or eyes. If contact has

been made, wash the affected area

with copious amounts of water and

seek medical advice.

f) Seek medical advice immediately

if a cell or battery pack has been

swallowed.

g) Keep battery pack clean and dry.

h) Wipe the battery pack terminals with

a clean dry cloth if they become dirty.

i) Battery pack needs to be charged

before use. Always refer to this

instruction and use the correct

charging procedure.

j) Do not maintain battery pack on

charge when not in use.

k) After extended periods of storage,

it may be necessary to charge

and discharge the battery pack

several times to obtain maximum

performance.

l) Battery pack gives its best

performance when it is operated at

normal room temperature (20°C ±

5°C).

m) When disposing of battery packs,

15

Cordless Limbing and Trimming Chain Saw

EN

keep battery packs of different

electrochemical systems separate

from each other.

n) Recharge only with the charger

speciﬁed by WORX. Do not use any

charger other than that speciﬁcally

provided for use with the equipment.

A charger that is suitable for one type of

battery pack may create a risk of ﬁre when

used with another battery pack.

o) Do not use any battery pack which

is not designed for use with the

equipment.

p) Keep battery pack out of the reach of

children.

q) Retain the original product literature

for future reference.

r) Remove the battery from the

equipment when not in use.

s) Dispose of properly.

SYMBOLS

Read the manual

Wear eye protection

Wear ear protection

Wear dust mask

Do not expose to rain

Do not burn

Do not expose to rain or water

XINR18/65-Y: Cylindrical lithium

Ion battery cells with max diameter

of 18mm and max height of

65mm; “x” represents a number

cells serial connected, blank if 1;

“-y” represents a number of cells

paralleled connected, blank if 1.

Do not dispose of batteries, Return

exhausted batteries to your local

collection or recycling point.

Waste electrical products must not

be disposed of with household

waste. Please recycle where

facilities exist. Check with your

local authorities or retailer for

recycling advice.

16

Cordless Limbing and Trimming Chain Saw

EN

INTENDED USE

This Jawsaw® has been designed for pruning

branches and cutting small logs up to 100mm

in diameter, not for cutting metals (See Fig. A).

ADJUSTMENT AND

ASSEMBLY

WARNING: Before touching the

chain or making any other

adjustments, make sure that the tool is

switched off and the battery is removed.

All Saw Chains wear and become loose from

operation. Periodically check the Saw Chain

(8), if there is any visible gap between the

chain and the Guide Bar (7), it must be re-

tensioned.

WARNING: Remove the battery

from the tool before adjusting saw

chain tension.

Cutting edges on chain are sharp. Use

protective gloves when handling chain.

This product comes fully assembled. However,

we recommend that you check the chain

tension before use and readjust if necessary.

ADJUSTING THE CHAIN TENSION

1. Push the Rear Handle (1) until the Guide

Bar (7) is in the middle of the jaw opening

as shown. Lock the Guide Bar in the

middle position by inserting the Lock

Pin (12) into the Lock Pin Receptacle(13)

located under the Rear Handle (1) (See Fig.

B1 - B3).

2. Open the chain access cover (9) by using

the supplied wrench. To open turn the

Access Cover Nut no more than a 1/4 turn

in either direction. (See Fig. C)

3. Release tension on the Saw Chain (8) by

loosening the Chain Tensioning Bolt (10).

Turn the Chain Tensioning Bolt counter-

clockwise 2 or more times. (See Fig. D)

4. Add tension on the Saw Chain by turning

the Chain Tensioning Bolt clockwise. When

tightening the Chain Tensioning Bolt the

automatic chain tensioning system will set

the tension to the Saw Chain at the same

time.

NOTE: It is not possible to overtighten the

Saw Chain, so tighten the chain as much

as possible.

5. Check that the correct Saw Chain tension

has been set. It should be possible to pull

the Saw Chain away from the side of the

Guide Bar approximately 3 mm and it

should snap back. (See Fig. E)

If tension is incorrect, repeat step 3,

ensuring the Guide Bar is free to move

when the tension is released.

CHANGING THE GUIDE BAR AND SAW

CHAIN

WARNING!

• Laceration hazard. Always wear

protective gloves when installing or

removing the saw chain. The saw chain is

sharp and can cut you even when it is not

running.

• Burn hazard. The chain guide bar and

chain may become hot during use. Allow

to cool before adjustment or removal.

1. Ensure the operation is carried out on a

ﬁrm surface.

2. Remove the battery pack, install the Lock

Pin (12) and open the Chain Access Cover

(9) as described in the previous section.

3. Use only WORX replacement Guide Bar

and Saw Chain.

4. Loosen and remove the Chain Tensioning

Bolt (17).

5. Lift the Guide Bar (7) and Saw Chain (8)

out through the jaw, angling the Guide Bar

to clear the two bar locating pins (d) (See

Fig. I).

6. If replacing the Guide Bar, remove the

mounting plate (a), which is retained by a

single screw and ﬁt to the new Guide Bar.

The Guide Bar is symmetrical and may

be mounted with either face outward (can

be reversed if the lower working edge is

worn) (See Fig. F).

7. Before re-ﬁtting the Guide Bar, check that

the small oil hole (b) and chain slot (c) are

not blocked by dirt or sawdust, use a small

toothpick to clean if necessary (See Fig.

G1, G2).

8. Reﬁt the Saw Chain to the Guide Bar. Note

the correct direction of the teeth (See Fig.

H). The cutting direction is inward on the

lower cutting edge.

17

Cordless Limbing and Trimming Chain Saw

EN

9. With the mounting plate (a) side of the

Guide Bar facing the Motor (8) and holding

the Saw Chain in place on the bar, feed bar

and chain into the jaw, angling over the

bar locating pins (d) and pulling the Saw

Chain over the drive Sprocket (17) (see

Fig. I). There will be little excess Saw Chain

length, therefore, the Saw Chain must

be properly ﬁtted in the Guide Bar slot to

provide enough extra chain to be pulled

over the drive Sprocket.

10. Check if all parts are seated properly (See

Fig J).

11. Reﬁt and tighten the Chain Tensioning

Bolt. Note the cam (e) of the Chain

Tensioning Bolt will engage the projecting

tab (f) of the bar mounting plate and push

the bar outward to tension the chain, check

for correct tension (See ADJUSTING THE

CHAIN TENSION).

12. Close the Chain Access Cover and remove

the Lock Pin.

LUBRICATION

IMPORTANT: The Jawsaw® is

shipped with an empty oil tank. It

is essential to ﬁll with chain oil before

use. Bar and chain oil of any brand can

be used.

Never operate the Jawsaw® without

chain oil or an empty tank as this will

result in poor cutting performance,

motor overload and possible burn-out.

FILLING OIL TANK:

1. Fill Oil Bottle (19) with chain and bar oil.

(See Fig. K)

2. Rest the Jawsaw® with the Oil Filler facing

upward

3. Uncrew the oil ﬁller cap (g) open.

4. Use bottle to ﬁll oil reservoir. (See Fig. L)

5. Screw the oil ﬁller cap.

IMPORTANT: Use only the

recommended oil to avoid damage

to the Jawsaw®. Never use recycled/old

oil. Use of non approved oil will

invalidate the warranty.

CHECKING THE AUTOMATIC OILER

The Jawsaw® uses a much lower chain speed

than a conventional chainsaw so it needs

much less oil.

However it is very important that it always has

oil.

Check the Oil Level Window (14) and reﬁll as

necessary.

During operation, periodically check the

Saw Chain (8) and Guide Bar (7). A slight oil

presence should be visible. If the chain and

bar appear completely dry, then remove the

bar and chain (see previous section) to ensure

the bar oil hole is not blocked.

If the oil hole is clear, there is oil in the tank

and still no oiling of the chain is visible –

contact Worx customer service.

WARNING: Do not push the rear

handle repeatedly when the saw is not

cutting. The oil will be bumped out when

pushing the handle whether the motor runs or

not.

OPERATION

1. BEFORE USING YOUR CORDLESS

TOOL

Your bat tery pack is UNCHARGED and you

must charge once before use.

The battery charger supplied is matched to the

Li-ion battery installed in the machine. Do not

use another battery charger.

2. CHARGING YOUR BATTERY PACK

The Li-ion battery is protected against deep

discharging. When the battery is empty,

the machine is switched off by means of a

protective circuit.

In a warm environment or after heavy use, the

battery pack may become too hot to permit

charging. Allow time for the battery to cool

down before recharging.

3. TO REMOVE OR INSTALL BATTERY

PACK(See Fig. M)

Depress the battery release button to release

battery pack from your tool. After recharging,

insert the battery pack into the battery port.

A simple push and slight pressure will be

sufﬁcient.

18

Cordless Limbing and Trimming Chain Saw

EN

PREPARE YOUR JAWSAW® FOR USE

WARNING!

• Read and understand all instructions.

Failure to follow all instructions listed

may result in electric shock, ﬁre and/

or serious personal injury.

• Sharp moving blade. To prevent

accidental operation, ensure that

the battery pack is removed before

performing the following operations,

failure to do this could result in

serious personal injury.

CAUTION: Sharp moving blade.

Always wear protective gloves

when installing or removing the chain,

the Saw Chain (8) is sharp and can cut

you when it is not running.

WARNING:

• Never operate a Jawsaw® that is

damaged or improperly adjusted or

that is not completely and securely

assembled.

• Be sure that the saw chain stops

moving when the power control

system triggers are released.

• Never adjust the guide bar or saw

when battery pack is connected .

SWITCHING ON AND OFF

The Trigger Switch (2) is locked to prevent

accidental starting.

There are two Lock Out Buttons (3), to

allow upright (cutting down from the top)

or inverted (cutting up from the bottom)

operation.

To switch on, press either Lock Out Button

with your thumb and squeeze the Trigger

Switch (See Fig. N).

To switch off, just release the Trigger Switch.

CUTTING

Check oil level window (14) prior to starting

and regularly during operation. Reﬁll oil when

oil level is low.

If operating with a newly replaced Saw Chain

(8), check the chain tension around every 10

minutes during operation.

Always hold the Front Handle (4) ﬁrmly when

cutting (See Fig. O1, O2)

1. Use both hands to grip saw ﬁrmly. Always

use your left hand (I) to grip the front

handle and your right hand (II) to grip the

Rear Handle(1). Thumbs and ﬁngers must

wrap around saw handles (See Fig. O1,

O2).

2. IMPORTANT: Make sure your

footing is ﬁrm and stable. Do not

use the Jawsaw® while standing on piles

of branches or while standing on a ladder.

HINT: When cutting branches which are

lying on the ground, place one foot on the

branch to prevent limb from moving (See

Fig. P).

WARNING! Do not put your foot in

the Jaw teeth, keep your foot a safe

distance from the tool. (See Fig. P)

3. Position the tool with the Jaw placed over

the desired branch to be cut.

WARNING: DO NOT force the cut.

Let the Saw Chain pull through the

wood.

WARNING: When starting the saw

make sure the chain is not in contact

with the limb or branch to be cut.

4. Switch on the tool.

5. Push the Rear Handle towards the Front

Handle to complete the cut.

6. Switch off the tool after the Guide Bar and

Saw Chain have returned to their starting

position.

WARNING:

• When completing the cut (step 6 above)

do not push the handle forcefully, let the

spinning chain pull itself through the

wood.

• Using too much force on the rear handle

when cutting can overload the tools

motor.

CAUTION: At the end of each cut be

prepared to support the tools weight.

TRIMMING BRANCHES:

Before cutting any branch, you must consider

the following:

1. Is the branch heavy, will it damage

anything when it falls?

• Large branches should be cut in small

sections starting at the farthest end from

the tree.

19

Cordless Limbing and Trimming Chain Saw

EN

• Always check where the branch will fall

BEFORE commencing the cut.

• Never stand under a branch being cut.

2. Will the branch split before it is cut

through? (See Fig. Q1, Q2)

• To prevent splitting, turn the Jawsaw®

upsidedown and make a small cut (less

than 1/3 diameter of the limb) from the

underside.

• Then turn the Jawsaw® over to the normal

position and cut from top down, slightly

further out from the trunk than the initial

undercut.

3. Is the branch under tension, will it spring

suddenly or trap the saw when it is cut?

• Always stand outside the path of a

springy branch. It can strike suddenly with

surprising force and cause injury or loss of

control of the saw.

• Always cut from the tension side of a

branch, usually the top of a branch on a

standing tree, but can be any side of the

branch of a fallen tree.

• If the cut starts to close on the saw, you

are cutting from the wrong side, keep the

saw running and pull the saw to retract

the blade from the cut.

• If the saw becomes trapped do not try

to pull it out with excessive force, lift the

branch to open the cut while an assistant

removes the saw.

KICKBACK SAFETY

This saws chain is covered by a guard

however, kickback can still occur. The following

steps will reduce the risk of kickback

• Use both hands to grip saw while saw

is running. Use ﬁrm grip. Thumbs and

ﬁngers must wrap around saw handles.

• Keep all safety items in place on saw.

Make sure they work properly.

• Do not overreach.

• Keep solid footing and balance at all

times.

• Stand slightly to right left side of saw. This

keeps your body from being in direct line

with Saw Chain.

• Do not let guide bar nose touch anything

when Saw Chain is moving.

• Do not bury Guide Bar nose or try to

plunge cut (boring into wood using bar

nose).

• Watch for shifting of wood or other forces

that may pinch Saw Chain.

• Use extreme caution when reentering a

previous cut.

• Never use a dull or loose Saw Chain. Keep

Saw Chain sharp with proper tension.

PROPERLY USING THE Jawsaw®

Use the Jawsaw® only with secure footing.

Hold the Jawsaw® at the right-hand side of

your body. (See Fig. R)

The Saw Chain must be running at full speed

before it makes contact with the wood. Use

the metal Jaw Teeth (6) to secure the saw onto

the wood before starting to cut. (See Fig. S)

Do not operate the Jawsaw® with arms fully

extended or attempt to saw areas which are

difﬁcult to reach, or on a ladder. (See Fig. T)

CUTTING WOOD UNDER TENSION (See

Fig. U)

WARNING: When cutting a limb

that is under tension, use extreme

caution. Be alert for wood springing

back. When wood tension is released,

the limb could spring back and strike

operator causing severe injury or death.

When sawing logs supported on both ends,

start the cut from above(Y) about 1/3 of the

diameter into the log and then ﬁnish the cut

(Z) from below, in order to avoid contact of the

Jawsaw® with the ground. When sawing logs

supported on only one end, start the cut from

below (Y) about 1/3 of the diameter into the

log and ﬁnish the cut from above (Z) in order

to avoid log splitting or jamming of the tool.

LIMBING A TREE (See Fig. V)

Limbing is removing the branches from a

fallen tree. When limbing leave larger lower

limbs to support the log off the ground.

Remove the small limbs in one cut as

illustrated. Branches under tension against the

ground should be cut from the bottom up to

avoid binding the Jawsaw®.

BUCKING A LOG (See Fig. W)

Bucking is cutting a log into lengths. It is

important to make sure your footing is ﬁrm

and your weight is evenly distributed on both

feet. Follow the simple directions for easy

cutting.

20

Cordless Limbing and Trimming Chain Saw

EN

WARNING: (See Fig. X)

• If on slope, make sure log will not

roll down hill. Secure log by using

wooden stakes. Drive wooden stakes

into ground on downhill side of log.

Stand on uphill side of log while

cutting. Log may roll after cutting.

(See Fig. X)

• Never try cutting through two logs

at same time. This could increase the

risk of kickback.

• While cutting log, never hold log with

your hand or leg.

• While cutting log, never allow another

person to hold log.

• Turn off and remove the battery pack

from the saw before moving from one

place to another.

SAW MAINTENANCE AND

KICKBACK SAFETY

Follow maintenance instructions in this

manual. Proper cleaning and maintenance of

the Saw Chain (8) and Guide Bar (7), as well as

the Jawsaw® in general, can reduce chances of

kickback. Inspect and maintain saw after each

use. This will increase the service life of your

saw.

NOTE: Even with proper sharpening, risk of

kickback can increase with each sharpening.

MAINTENANCE AND

STORAGE OF JAWSAW®

1. Remove the battery pack from the saw:

• When not in use.

• When transporting.

• When left unattended.

• Before servicing.

• Before cleaning.

• Before changing accessories or

attachments, such as Saw Chain and

Guard Bar.

2. Inspect the saw before and after each use

for:

• Any signs of damage.

• Smooth action of push handle and

movement of bar.

• Adequate Chain Tension; you should be

able to lift the Saw Chain from the Guide

Bar no more than 3 mm.

• Adequate chain lubrication.

3. Do not use the Jawsaw®, if:

• The Trigger Switch (2) or Lock Out Button

(3) is malfunctioning.

• The Rear (Push) Handle (1) does not

smoothly return under spring force.

• Any other damage which affects the safety

or operation is evident.

4. Maintain the Jawsaw® with care and have

any damage or malfunction repaired by an

authorized service center:

• Never expose the Jawsaw® to rain.

• Keep Saw Chain sharp, clean, and

lubricated for better and safer

performance.

• Follow steps outlined in this manual to

sharpen Saw Chain.

• Keep handles clean and free from oil.

• Keep all screws and nuts tight.

5. When servicing, use only identical

replacement parts.

6. When not in use, always store Jawsaw®

• In a high or locked place, out of children’s

reach.

• In a dry place.

REPLACING SAW CHAIN/CHAIN BAR

Replace the Saw Chain when cutters are too

worn to sharpen or when chain breaks. Only

use replacement chain noted in this manual.

Always include new drive Sprocket (16) when

replacing the Saw Chain. This will maintain

proper driving of chain. Inspect Guide Bar (7)

before sharpening chain. A worn or damaged

guide bar is unsafe. A worn or damaged Guide

Bar is unsafe, will damage the Saw Chain, and

will make cutting harder.

For Replacing the Guide Bar please refer to

CHANGING THE GUIDE BAR AND CHAIN

section in the Adjustment and Assembly

Instructions.

SHARPENING SAW CHAIN

WARNING: Remove the battery

pack from the saw before servicing.

Cutting edges on chain are sharp. Use

protective gloves when handling chain.

Leht laadib ...

Worx WX014 Kasutusjuhend

Worx WX014 Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid