Rugged Cover Premium Vinyl Tri-Fold Cover paigaldusjuhend

Tüüp
paigaldusjuhend
How To Adjust Clamps
The clamps might need adjusted.
To adjust, turn handle on clamp clockwise to
tighten or counter clockwise to loosen.
Lip of clamp
D1
D2
D3
1. Place the cover on
front of truck bed.
1
4
5
6
7
8
2&7. To clamp cover down, put
lip of clamp under side
bed rail and push handle
down. (See D1, D2, D3)
3
3. Attach safety
tether strap on
both sides.
4. Undo both clips
so cover can be
unfolded.
5. Unfold first
section.
6. Unfold
second
section.
7. Cover is laying down flat.
8. Secure rear clamps for a
tight fit.
9. Vehicles With Utility Track
All Toyota Tacoma or Tundra Pickups.
2007 GMC/Chevy Pickups
2008 Ford Pickups
2008 Nissan Pickups
2008 Dodge Pickups
Use aluminum block to attach cover by
sliding into place and locking clamping on
to blocks. (See Back For Details)
Page 1
Tonneau Cover
is locked
into position
when handle is
down on both sides
Patent No’s.
7,823,957 /
8,146,982 /
8,256,824
Use orange clip to store clamp when cover is folded.
7-24-13
Premium Vinyl Tri-Fold Cover
Installation Instructions
Use orange clip to store
knob when cover is
folded.
200 Universal Dr.
Owosso, MI 48867
989-725-8354
Fax: 989-725-8409
1-800-433-3604
2. Secure
cab clamp
hooks under
the metal bed
rail.
Toyota Models
Only - Tighten
lock nut at
bottom of
knob.
2
Page 2
9
A
GM Pickups with
Utility Track
B
C
D
A. Slide aluminum blocks into track,
position and tighten set-screw.
B. Secure front clamp on to
aluminum block.
C. Attach safety strap on both sides
to aluminum block.
D. Attach rear clamps
A
Nissan Pickups with
Utility Track
B
C
D
9
A
Toyota Pickups with
Utility Track
B
C
D
9
A
Dodge Pickups with
Utility Track
B
C
D
9
Useful Information.
A. Loosen rear 2 bolt’s on utility track and
slide aluminum blocks into track.
B. Re-tighten rear 2 bolt’s. Then position
and tighten blocks with set-screw.
C. Secure front clamp & safety strap to
aluminum block on both sides.
D. Attach rear clamps.
10
A.
If there is a gap
from the corner
to the edge of
the wing tailgate
piece when the
cover is fastened.
(1) You can put
an extra foam
corner piece on
the back existing
corner pieces.
(2) Take the roll
of foam and measure from the edge of the tailgate piece
to the edge of the corner piece on both sides, cut and
stick to existing foam.
(1)
(2)
(A)
B.
Or, Replace the Wing Style Tailgate Piece with a Flatter
Style Tailgate Piece.
A
Ford Pickups with
Utility Track
B
C
D
9
A. Slide aluminum blocks into track,
position and tighten set-screw.
B. Secure front clamp on to
aluminum block.
C. Attach safety strap on both sides
to aluminum block.
D. Attach rear clamps
A. Slide aluminum blocks into track,
position and tighten set-screw.
B. Secure front clamp on to
aluminum block.
C. Attach safety strap on both sides
to aluminum block.
D. Attach rear clamps
A. Slide aluminum blocks into track,
position and tighten set-screw.
B. Secure front clamp on to
aluminum block.
C. Attach safety strap on both sides
to aluminum block.
D. Attach rear clamps
7-24-13
  • Page 1 1
  • Page 2 2

Rugged Cover Premium Vinyl Tri-Fold Cover paigaldusjuhend

Tüüp
paigaldusjuhend