Panasonic SC-PMX9 Omaniku manuaal

Bränd: Panasonic

Mudel: SC-PMX9

Kategooria: CD-mängijad

Tüüp: Omaniku manuaal

See käsiraamat sobib ka

SCPMX9EG

VQT4Z21

until

2013/5/8

Thank you for purchasing this product.

Please read these instructions carefully before using this product, and save this

manual for future use.

Dziękujemy za zakupienie tego produktu.

Przed przystąpieniem do eksploatacji opisywanego produktu należy dokładnie

przeczytać niniejsze zalecenia i zachować instrukcję obsługi do wglądu.

Děkujeme za zakoupení tohoto výrobku.

Před použitím tohoto produktu si pečlivě přečtěte tyto pokyny a celý návod si uložte

pro pozdější použití.

Kiitos, että hankit tämän tuotteen.

Lue nämä ohjeet huolellisesti ennen tämän tuotteen käyttämistä ja säilytä tämä

käsikirja tulevaa tarvetta varten.

Operating Instructions

Instrukcja obsługi

Návod k obsluze

Käyttöohjeet

CD Stereo System

Zestaw stereo z CD

Stereosystém s CD

CD-stereojärjestelmä

Model No. SC-PMX9

SC-PMX9EG-VQT4Z21.book 1 ページ２０１３年３月２２日　金曜日　午後４時５４分

VQT4Z21

ENGLISH

Do the procedures with the remote control. You can

also use the buttons on the main unit if they are the

same.

Your system and the illustrations can look differently.

These operating instructions are applicable to the

following system.

Safety precautions

Unit

• To reduce the risk of fire, electric shock or product damage,

- Do not expose this unit to rain, moisture, dripping or

splashing.

- Do not place objects filled with liquids, such as vases, on

this unit.

- Use only the recommended accessories.

- Do not remove covers.

- Do not repair this unit by yourself. Refer servicing to

qualified service personnel.

Unit

• To reduce the risk of fire, electric shock or product damage,

- Do not install or place this unit in a bookcase, built-in

cabinet or in another confined space. Ensure this unit is

well ventilated.

- Do not obstruct this unit’s ventilation openings with

newspapers, tablecloths, curtains, and similar items.

- Do not place sources of naked flames, such as lighted

candles, on this unit.

• This unit is intended for use in moderate climates.

• The mains plug is the disconnecting device.

Install this unit so that the mains plug can be unplugged

from the socket outlet immediately.

• This unit may receive radio interference caused by mobile

telephones during use. If such interference occurs, please

increase separation between this unit and the mobile

telephone.

• This unit utilizes a laser. Use of controls or adjustments or

performance of procedures other than those specified

herein may result in hazardous radiation exposure.

Battery

• Do not break open or short-circuit the battery.

• Do not charge the alkaline or manganese battery.

• Do not use the battery if the cover has peeled off.

• Do not heat or expose to flame.

• Do not leave the battery(ies) in a car exposed to direct

sunlight for a long period of time with doors and windows

closed.

• Remove the battery if you do not use the remote control for

a long period of time. Keep in a cool, dark area.

• Danger of explosion if battery is incorrectly replaced.

Replace only with the type recommended by the

manufacturer.

• When disposing the batteries, please contact your local

authorities or dealer and ask for the correct method of disposal.

Android, Google Play and Chrome are trademarks of Google Inc.

DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks,

service marks, or certification marks of the Digital Living Network

Alliance.

The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi

Alliance.

The Wi-Fi Protected Setup Mark is a mark of the Wi-Fi Alliance.

“Wi-Fi”, “Wi-Fi Protected Setup”, “WPA” and “WPA2” are marks or

registered marks of the Wi-Fi Alliance.

MPEG Layer-3 audio coding technology licensed from Fraunhofer

IIS and Thomson.

The Bluetooth

word mark and logos are owned by the Bluetooth

SIG, Inc. and any use of such marks by Panasonic Corporation is

under license.

Other trademarks and trade names are those of their respective

owners.

Windows is a trademark or a registered trademark of Microsoft

Corporation in the United States and other countries.

Table of contents

Safety precautions...........................................2

Supplied accessories ......................................3

Maintenance .....................................................3

Preparing the remote control.......................... 3

Making the connections..................................3

Placement of speakers.................................... 4

Overview of controls ....................................... 4

Inserting media ................................................ 5

Media information............................................ 5

Network settings.............................................. 6

Using AirPlay with this system’s speakers... 9

Playing back music files on the DLNA server.....10

Bluetooth

operations ................................... 11

About Bluetooth

........................................... 11

Media Playback operations...........................12

Radio............................................................... 13

Clock and timers............................................ 13

Sound effects .................................................14

Using the auxiliary input ............................... 14

Others .............................................................14

Troubleshooting.............................................16

Specifications ................................................ 18

“Made for iPod”, “Made for iPhone”, and “Made for iPad” mean

that an electronic accessory has been designed to connect

specifically to iPod, iPhone, or iPad, respectively, and has been

certified by the developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its

compliance with safety and regulatory standards.

Please note that the use of this accessory with iPod, iPhone, or

iPad may affect wireless performance.

AirPlay, the AirPlay logo, iPad, iPhone, iPod, iPod classic, iPod

nano, and iPod touch are trademarks of Apple Inc., registered in

the U.S. and other countries.

App Store is a service mark of Apple Inc.

System SC-PMX9

Main unit SA-PMX9

Speakers SB-PMX9

WARNING!

CAUTION!

SC-PMX9EG-VQT4Z21.book 2 ページ２０１３年３月２２日　金曜日　午後４時５４分

ENGLISH

VQT4Z21

Supplied accessories

Check and identify the supplied accessories.

Maintenance

• To clean the main unit, wipe with a soft, dry cloth.

• To clean the speakers, wipe with a fine-textured and

dry cloth such as a microfibre cleaning cloth.

• Never use alcohol, paint thinner or benzine to clean

this system.

• Before using chemically treated cloth, read the

instructions that came with the cloth carefully.

Preparing the remote control

• Use alkaline or manganese battery.

• Install the battery so that the poles (+ and –) align with

those in the remote control.

• Point the remote control at the remote control sensor,

away from obstacles, at a maximum range of 7 m

directly in front of the main unit, within an angle of

approximately 30° to the left and right.

Making the connections

Connect the AC mains lead only after all the other

connections have been made.

1 Connect the FM indoor antenna.

Place the antenna where reception is best.

•

Use an FM outdoor antenna if radio reception is poor.

2 Connect the speakers.

Be careful not to cross (short-circuit) or reverse

the polarity of the speaker wires as doing so may

damage the speakers.

• Connect the cable with a red line to the red terminal

(r).

3 Connect the AC mains lead.

Do not use an AC mains lead with other equipment.

Conserving power

The system consumes approximately 0.4 W when it is in standby

mode. Disconnect the power supply if you do not use the system.

Some settings will be lost after you disconnect the

system. You have to set them again.

You can connect a VCR, DVD player etc.

Note:

• Disconnect the AC mains lead before connection.

• Switch off all equipment and read the appropriate operating

instructions.

• Components and cables are sold separately.

• If you want to connect equipment other than those

described, refer to the audio dealer.

• Sound distortion can occur when you use an adaptor.

• For information on the connection of a LAN cable, refer to

page 6.

1 x AC mains lead 1 x Remote control

(N2QAYB000896)

1 x FM indoor antenna 1 x Remote control

battery

2 x Speaker cables

R6/LR6, AA

To household mains socket

Tape

(not supplied)

Black

Red

Black Red

Cable with

a red line

Connecting other equipment

DVD player (not supplied)

Rear panel of

this main unit

Audio cable (not supplied)

SC-PMX9EG-VQT4Z21.book 3 ページ２０１３年３月２２日　金曜日　午後４時５４分

VQT4Z21

ENGLISH

Placement of speakers

Place the speakers so that the tweeter is on the inner

side. To prevent damage to the speakers, do not touch

the speaker cones if you remove the nets.

Use only the supplied speakers.

The combination of the main unit and speakers give the

best sound. You can cause damage to the system and

decrease the sound quality if you use other speakers.

Note:

• Keep your speakers more than 10 mm from the main unit

for ventilation.

• Put the speakers on a flat safe surface.

• These speakers do not have magnetic shielding. Do not

put them near TVs, PCs or other equipment easily

influenced by magnetism.

• When you play at high levels for a long period, it can cause

damage to the system and decrease the life of the system.

• Decrease the volume in these conditions to prevent

damage:

- When you play distorted sound.

- When you adjust the sound quality.

Overview of controls

1 Standby/on switch [Í], [Í/I]

Press to switch the unit from on to standby mode or

vice versa. In standby mode, the unit is still

consuming a small amount of power.

2 Numeric buttons [1 to 9, 0, S10]

To select a 2-digit number

Example: 16: [S10]

> [1] > [6]

3 Delete a programmed track

4 Select audio source

5 Basic playback control

6 Select the sound effects

7 View the iPod menu

8 View content information

9 Clock and timer operation

10 Set the programme function

11 Adjust the volume of the system

12 Mute the sound of the system

Press the button again to cancel.

“MUTE” is also cancelled when you adjust the

volume or when you switch off the system.

13 Set the play menu item

14 Set the radio menu item

15 Select the option

16 Enter setup menu

17 “iPod_Dock” for iPod/iPhone

18 Headphones jack ( )

• Plug type: Ø 3.5 mm stereo (not supplied)

• Avoid listening for prolonged periods of time to

prevent hearing damage.

• Excessive sound pressure from earphones and

headphones can cause hearing loss.

• Listening at full volume for long periods may

damage the user’s ears.

19 Display panel

20 “iPod_Port” for iPod/iPhone/iPad and USB devices

21 Open or close the disc tray

22 Disc tray

23 Remote control sensor

CAUTION!

• Use the speakers only with the recommended

system. If not, you can cause damage to the

amplifier and speakers and can cause a fire.

Consult an approved service personnel if damage

occurs or if there is a sudden apparent change in

performance.

• Do the procedures included in these instructions

when you attach the speakers.

Tweeter

OPEN/CLOSE

D.BASS

VOLUME

SELECTORCDiPod

BASS TREBLE

iPad

SETUP

SELECTOR

Top view

[iPod]: “iPod_Dock” ,. “iPod_Port” / “USB”

[CD]: “CD”

[SELECTOR]:

“CD”

----------------. “BLUETOOTH” -----------------. “FM”

“iPod_Port” / “USB”

(

“iPod_Dock”

(

“AUX”

SC-PMX9EG-VQT4Z21.book 4 ページ２０１３年３月２２日　金曜日　午後４時５４分

ENGLISH

VQT4Z21

Inserting media

“iPod_Dock” (Using Lightning connector):

• Make sure that the iPod/iPhone is fully inserted and its

back is resting against the cushion pad.

• Make sure to remove the iPod/iPhone from its case.

• Make sure to align your iPod/iPhone with the

connector when inserting.

“iPod_Port”:

• Use the dedicated USB cable (not supplied) for iPod/

iPhone/iPad.

• Insert the USB device directly. Do not use any USB

extension cable.

• Before removing the USB device, select a source other

than “USB”.

Disc tray:

• Remove the CD only after it stops rotating.

Charging starts when an iPod/iPhone/iPad is connected

to this system.

• During standby mode, charging will not start from the

“iPod_Port” connection, however it will start as usual

from the “iPod_Dock” connection.

- To charge from the “iPod_Port” connection, start the

charging before turning this unit to standby mode.

• See the iPod/iPhone/iPad display for its battery

charging status.

• Disconnect the iPod/iPhone/iPad if it is not used for an

extended period of time after charging is complete.

• Charging stops when the battery is fully charged. The

battery will deplete naturally.

Media information

• Please be aware that Panasonic accepts no

responsibility for the loss of data and/or information.

Compatible with “iPod_Dock” connection

(Using Lightning connector)

Compatible with “iPod_Port” connection

[Using dedicated USB cable (not supplied)]

Note:

• Compatibility depends on the software version. Update

your iPod/iPhone/iPad to the latest software before

using it with this unit.

• Read the User Guide of the iPod/iPhone/iPad for the

operating instructions.

• USB devices that support bulk-only transfer.

Note:

• Files are defined as tracks and folders are defined as

albums.

• Track must have the extension “.mp3”, “.MP3”, “.flac” or

“.FLAC”.

• This system can access up to:

- 255 albums (including root folder)

- 2500 tracks

- 999 tracks in one album

• CBI (Control/Bulk/Interrupt) is not supported.

• Some files can fail to work because of the sector size.

• NTFS file system is not supported (only FAT16/FAT32 file

system is supported).

• This system can play CD-R/RW with CD-DA or MP3

format content.

• Disc must conform to ISO9660 level 1 or 2 (except for

extended formats).

Note:

• Some CD-R/RW cannot be played because of the

condition of the recording.

• MP3 files are defined as tracks and folders are defined as

albums.

• This system can access up to:

- CD-DA: 99 tracks

- MP3: 999 tracks, 255 albums (including root folder) and

20 sessions

• Recordings will not necessarily be played in the order you

recorded them.

iPad

OPEN/CLOSE

iPod/iPhone

(not supplied)

Lightning connector

Select “iPod_Dock” as the source

Open the cover and connect an iPod/iPhone with

Lightning connector.

Select “iPod_Port” as the source

“USB” is displayed when a compatible

USB device is inserted.

• Do not connect the following models:

iPod classic, iPod [4th (colour display),

and 5th (video) generation], iPod nano

(1st generation)

Unexpected behaviour may occur.

Select “CD” as the

source

Charging an iPod/iPhone/iPad

Compatible iPod/iPhone/iPad (as of January 2013)

iPod touch (5th generation)

iPod nano (7th generation)

iPhone 5

iPod touch (1st, 2nd, 3rd, 4th, and 5th generation)

iPod nano (2nd, 3rd, 4th, 5th, 6th, and 7th generation)

iPhone 5 / iPhone 4S / iPhone 4 / iPhone 3GS /

iPhone 3G / iPhone

iPad (3rd, and 4th generation) / iPad 2 / iPad

iPad mini

Compatible USB devices

Compatible CD

SC-PMX9EG-VQT4Z21.book 5 ページ２０１３年３月２２日　金曜日　午後４時５４分

VQT4Z21

ENGLISH

Network settings

You can stream music from an iOS device (iPhone, iPod,

iPad), an Android™ device or a Mac/PC to this system’s

speakers by using the AirPlay or DLNA feature.

To use these features, this system must join the same

network as the AirPlay compatible device (> 9) or the

DLNA compatible device.

• It is also possible to use AirPlay without a network router.

(> 10, “Directly streaming to this system (AirPlay)”)

• Switching between a wired LAN connection and a wireless

LAN connection may cause the connection settings to be

initialized. In that case, make the settings again.

• For a stable connection to the network, a wired LAN

connection is recommended.

Normally, just connecting a LAN cable will complete the setup.

1 Connect the main unit to a broadband router, etc.

using LAN cable while the AC mains lead is

disconnected.

2 Connect the AC mains lead to the main unit and

turn this system on.

This unit is ready for use when “ ” is indicated on

the display.

• The LAN cable must be connected or disconnected

while the AC mains lead is disconnected.

• Use category 5 or above straight LAN cables (STP)

when connecting to peripheral devices.

• Inserting any cable other than a LAN cable in the LAN

port can damage the unit.

• When a LAN cable is connected, wireless settings will

be cancelled.

This system has built-in Wi-Fi

and can be connected to

a wireless router.

Preparation

• Place this system as close to the wireless network

router as possible.

• Disconnect the LAN cable.

• Point the antenna on the rear of

the main unit up as shown in the

figure.

• Do not perform the following:

- Tilting the antenna forward or

backwards when it is pointing up

- Applying too much force to the

antenna

- Carrying this unit by holding the antenna

1 Turn this system on.

2 Follow the chart below to choose the network

setting method.

Wired LAN connection

LAN Cable

(not supplied)

Broadband router, etc.

e.g.,

You can perform network-related settings individually.

jIf your home wireless network has been configured to

use specific IP Addresses, Subnet Mask, Default

Gateway, Primary DNS, etc.

jIf you want to change the name of this system that is

displayed as the AirPlay speakers or DLNA renderer.

1 Connect the main unit directly to your computer using

LAN cable while the AC mains lead is disconnected.

2 Connect the AC mains lead to the main unit and turn

this system on.

3After

“ ” is indicated on the display,

check the IP

address for this unit. (

15, “IP/MAC Address”)

4 Press [SETUP] on the remote control repeatedly to

select “Net Setup” and then press [OK].

5 Press [SETUP] on the remote control repeatedly to

select “Manual” and then press [OK].

6 When “Setting” blinks on the display, start an Internet

browser on your computer and then type the IP address

for this unit checked in step 3 into the address field and

display the setup screen.*

7 Select and input the details.

8 Select “JOIN” to apply the settings.

9 The settings are completed when “Success” is displayed.

10 Turn off this unit and then disconnect the AC mains lead.

11 Perform “Wired LAN connection”. (> left)

* It may take a few minutes until the setup screen is

available to be displayed on the browser depending on

the environment.In that case, reload the browser.

Wireless LAN connection

Wireless router, etc.

e.g.,

Does your wireless network router support

WPS?

Yes

“Method 1”

l 7,

“Method 2”

l 7,

“Method 3”

No / Do not know

Yes No

Are you using an

iPod touch/iPhone/iPad?

Is the iOS version 5.0 or later?

SC-PMX9EG-VQT4Z21.book 6 ページ２０１３年３月２２日　金曜日　午後４時５４分

ENGLISH

VQT4Z21

• If you want to perform wireless setting with your

Mac/PC, or you want to apply the advanced setting,

try “Method 4” on page 8.

• To cancel this setting in the middle, press [Í] to turn off this

system.

• Simultaneous use with other 2.4 GHz devices, such as

microwaves, cordless telephones, etc., may result in

connection interruptions.

• For up to date compatibility information on your wireless

network router refer to

http://panasonic.jp/support/global/cs/

(This site is in English only.)

∫ Using the WPS Push Button Configuration

(PBC)

1 Press [SETUP] on the remote control repeatedly

to select “Net Setup” and then press [OK]. *1

“With iPod” is indicated on the display.

2 Press [SETUP] on the remote control repeatedly

to select “WPS Push” and then press [OK]. *1

“WPS” flashes on the display.

• Complete step 3 within 2 mins.

3 After “WPS” is indicated, press the WPS button

on the wireless network router.

4 The settings are completed when “Success” is

displayed.

“ ” is indicated on the display.

5 Press [OK] on the remote control to exit the

setting.

• This system can also be set using the WPS PIN code.

(Before starting, refer to the wireless network router’s operating

instructions for details on how to enter the PIN code.)

1 Press [SETUP] on the remote control repeatedly to

select “Net Setup” and then press [OK]. *2

2 Press [SETUP] on the remote control repeatedly to

select “WPS PIN” and then press [OK]. *2

3 Enter the PIN code into the wireless network router.

*1 Replace with the following step.

Press and hold [D.BASS] on the main unit for 2 seconds

while pressing and holding [∫] on the main unit.

*2 Replace with the following steps.

1 Press and hold [D.BASS] on the main unit for 2 seconds

while pressing and holding [∫] on the main unit.

2 When “WPS” is indicated, press and hold [D.BASS] on

the main unit for 2 seconds while pressing and holding

[∫] on the main unit again.

With this method you will share the wireless network

settings of your iPod touch/iPhone/iPad with this system.

• The following explanations are based on an iPhone.

1 Disconnect iPod/iPhone/iPad connected to the

main unit.

2 Connect the iPhone to your home wireless

network.

3 Connect the iPhone to the main unit.

4 Press [SETUP] on the remote control repeatedly

to select “Net Setup” and then press [OK].

“With iPod” is indicated on the display.

5 Unlock your iPhone and then press [OK] on the

remote control.

“Connecting Wi-Fi” is indicated on the display.

• If “Not Supported” or “Set Wi-Fi” is displayed, check

that the iPhone is connected to the wireless network

and try again from step 1.

6 A message will pop-up on your iPhone.

Allow the iPhone to share the wireless network

settings.*

7 The settings are completed when “Success” is

displayed.

“ ” is indicated on the display.

8 Press [OK] on the remote control to exit the

settings.

*1: Depending on the network environment or the wireless

network router settings, it may take more than 10 mins.

to complete the settings.

You can make the wireless network settings with the

app, “Panasonic Stereo System Network Setup” (for

free).

If you’re using an Android device, download the app at

Google Play™. If you’re using an iPod touch/iPhone/

iPad, download it at the App Store.

Preparation

• Connect your smartphone to your home wireless

network.

• Check the password for your home wireless network.

1 Press [SETUP] on the remote control repeatedly

to select “Net Setup” and then press [OK].

“With iPod” is indicated on the display.

2 Press [SETUP] on the remote control repeatedly

to select “Manual” and then press [OK].

“Setting” blinks on the display.

3 Start “Panasonic Stereo System Network Setup”

on your smartphone and follow the indications.

(Continued on the next page)

Method 1

If your wireless network router supports WPS

(Wi-Fi Protected Setup

The WPS identifier mark

WPS Push Button Configuration

(PBC) compatible wireless

network router may have this

mark.

“Fail” may be displayed if the connection was not made

within the set time limit. Try the setting again. If “Fail” is

still displayed, try other methods on page 7 or 8.

Method 2

If you're using an iPod touch/iPhone/iPad.

(iOS version 5.0 or later.)

If “Fail” is displayed press [OK] and try the setting

again. If “Fail” is still displayed, try other methods on

page 7 or 8.

• If the iPhone was disconnected midway through, try

again without disconnecting it.

Method 3

Setting the network connection with the smartphone

app.

SC-PMX9EG-VQT4Z21.book 7 ページ２０１３年３月２２日　金曜日　午後４時５４分

VQT4Z21

ENGLISH

∫ Note for the iOS version

After step 3

1 Enter the password for the home wireless network

to which the iOS device is connected.

2 When a message instructing you to connect the iOS

device to this system is displayed, press the home

button.

3 On the Wi-Fi network selection screen in “Settings”,

select “00 Setup _ _ _ _ _ _”.

• “ _ ” stands for a digit that is unique to each set.

4 When a message indicating the completion of the

connection to this system is displayed, restart the

app.

5 When a message indicating the completion of the

Wi-Fi setup of this system is displayed, close the

app, and then check the operation of AirPlay, etc.

• “Panasonic Stereo System Network Setup” for Mac OS is

also available at the Mac App Store.

With this method, you will access this system’s wireless

network settings from the Internet browser of your

compatible device.

• The following explanations are based on an iPhone.

1 Press [SETUP] on the remote control repeatedly

to select “Net Setup” and then press [OK].

“With iPod” is indicated on the display.

2 Press [SETUP] on the remote control repeatedly

to select “Manual” and then press [OK].

“Setting” blinks on the display.

3 After “Setting” blinks, connect your compatible

device to this system’s wireless network named

“00 Setup _ _ _ _ _ _”.

• “ _ ” stands for a digit that is unique to each set.

• Make sure that DHCP is enabled for the network

setting on your compatible device.

4 Start the Internet browser on your compatible

device and type “http://192.168.1.12/” into the

URL address field and display the page.

This system’s setup window is displayed.

• Examples of Internet browsers

iOS device/Mac : Safari

Android device : Google Chrome™

PC : Windows Internet Explorer

5 Select “Search wireless network”.

6 Select and input the details.

• Check your home wireless network name (Network

name (SSID)) and password for this network. This can

often be found on the wireless network router itself.

7 Select “JOIN” to apply the settings.

• In the pop-up screen, select “OK” to continue.

• Select “Cancel” to return to the setup window.

8 The settings are completed when “Success” is

displayed.

“ ” is indicated on the display.

9 Make sure to connect your compatible device

back to your home wireless network.

*1: If you have set your wireless network to be invisible,

select “BACK” and refer to “Alternative settings”. (> 9)

Method 4

Setting the network connection from an Internet

browser.

[1] Select your home wireless network

name.*

[2] Type the password.

If “Fail” is displayed press [OK], check the wireless

network password and other settings and start again

from step 1.

SC-PMX9EG-VQT4Z21.book 8 ページ２０１３年３月２２日　金曜日　午後４時５４分

ENGLISH

VQT4Z21

• The below settings are the alternative or additional settings

for “Method 4”. (> 8)

• Enable Java and Cookies in your browser settings.

Using AirPlay with this system’s

speakers

Preparation

• Complete the network settings. (> 6)

• Connect the iOS device or Mac/PC to the same home

network as this system.

1 Turn this system on.

• Check that “ ” is indicated on the display.

• If it doesn’t be indicated, check the network

settings. (> 6)

2 iOS device: Start the “Music” (or iPod) app.

Mac/PC: Start “iTunes”.

• If the Music app on your iOS device is used, select the

audio file you want to play.

3 Select “Panasonic PMX9 _ _ _ _ _ _”*

1, 2

from the

AirPlay icon.

{. Check the volume settings before starting the

playback. (When AirPlay is used for the first time, the

volume may be output at the maximum setting.)

4 Start play.

• The playback will start with a slight delay.

• This system can be set to turn on automatically when this

system is selected as the output speakers.

(> 15, “Network standby”)

• Playback of other audio sources will stop and AirPlay

output will have priority.

• Volume changes on the iOS device or iTunes will be

applied to this system. (Refer to the iTunes Help for the

required settings in iTunes.)

• With some iOS and iTunes versions, it may not be possible

to restart the AirPlay playback if the selector is changed

(e.g., “CD”) or this system is turned off, during the AirPlay

playback.

In this case, select a different device from the AirPlay icon

of the Music App or iTunes and then re-select this system

as the output speakers.

• AirPlay will not work when playing back videos on iTunes.

*1: “ _ ” stands for a digit that is unique to each set.

*2: The name that is displayed for this system can be

changed from the “Edit STEREO SYSTEM name”

settings.

left, "Advanced network settings")

(as of January 2013)

Advanced network settings

Alternative settings

Instead of steps 5 and 6

Select “Manual settings”.

1 Type your home wireless network name into the

“Network name (SSID)” field.

2 Select the encryption method from the “Security

system” drop down list.

3 Type the password into the “Password” field and

then select “JOIN”.

Additional settings

If your home wireless network has been configured to

use specific IP Addresses, Subnet Mask, Default

Gateway, Primary DNS, etc.

Before step 7

Select “Advanced network settings”.

Input the required addresses into each field and select “JOIN”.

• To change the settings back to DHCP, select “ON” from

the “DHCP” drop down list.

If you want to change the name of this system that

is displayed as the AirPlay speakers or DLNA

renderer.

Before step 5

Select “Additional settings”.

1 Select “Edit STEREO SYSTEM name”.

2 Type a new name into the

“STEREO SYSTEM name” field.

{. Only ASCII characters can be used.

3 Select “OK”.

4 If this system is already connected to your home

wireless network:

– Select “

Additional settings

”, and then select “

Exit

”.

If this system is not connected to your home

wireless network:

j Continue to step 5 of “Method 4”.

PMX9

e.g.,

“Music” app.

iPhone iOS 6.0.1

PMX9

e.g.,

iTunes 11.0

Compatible AirPlay devices

iOS 4.3.3 or later

iPod touch

3rd, 4th, and 5th generation

iPhone 5 / iPhone 4S / iPhone 4 / iPhone 3GS

iPad (3rd, and 4th generation) / iPad 2 / iPad

iPad mini

iTunes 10.2.2 or later (Mac / PC)

SC-PMX9EG-VQT4Z21.book 9 ページ２０１３年３月２２日　金曜日　午後４時５４分

VQT4Z21

ENGLISH

With this function set to “On”, you can stream music from

the iOS device or Mac / PC (iTunes 10.2.2 or later) to

this system without the need of a network router.

• Previous network settings will be deleted when this

function is set to “On”.

• The following explanations are based on an iPhone.

1 Press [SETUP] repeatedly to select “D.Connect”.

2 Press [2, 1] to select “On” and then press [OK].

3 Press [2, 1] to select “OK? Yes” and then press

[OK].

4 Connect your iPhone to this system’s wireless

network named “PMX9 _ _ _ _ _ _”*

5 Enter the password that is indicated on this

system’s display.

6 Once the iPhone is connected to this system’s

wireless network, the setup is competed.

7 Continue to step 2 of “Using AirPlay with this

system’s speakers”. (> 9)

• This setting is reset to “Off” when other network settings

are performed. (> 6)

• When “D.Connect” is set to “On”, this system will not be

connected to the Internet. It is not possible to update the

software or check the Wi-Fi signal strength.

• When AirPlay is not being used, disconnect the AirPlay

compatible device from this network.

• When using a computer on this network, make sure that all

the shared files are encrypted.

• This feature is only compatible with the “Open System”

authentication method. It is not compatible with “Shared

Key” authentication method.

*1: “ _ ” stands for a digit.

*2: “ _ ” stands for a digit that is unique to each set.

The first time “D.Connect” is set to “On”, a password for

this system’s network is randomly created and

memorised in this system.

• This password is memorised until it is changed.

1 While “D.Connect” is set to “On”:

Press [SETUP] repeatedly to select “D.Connect”.

2 Press [2, 1] to select “On” and then press [OK].

3 The current password is displayed.

• The 5 digits after “PW” is the password for this

network.

4 Press any button to exit.

1 While “D.Connect” is set to “Off”:

Press [SETUP] repeatedly to select “D.Connect”.

2 Press [2, 1] to select “Change PW” and then press

[OK].

3 Press [2, 1] to select “OK? Yes” and then press

[OK].

4 The new password is displayed.

• The 5 digits after “PW” is the new password for

this network.

5 Press any button to exit.

∫ Note about changing the password

After changing this system’s network password, if you

are not prompted to change the password on the other

devices, the following changes are required.

iOS device (iPod touch/iPhone/iPad)

• Before choosing this system’s network,

1 Select [ ] located beside this system’s wireless

network name.

Select “Forget this Network” and then select “Forget”.

3 Select this system’s wireless network and enter the

new password.

Mac/PC:

• If the computer has memorised the old password, be

sure to change the memorised password for this

system’s network to the new one.

• Refer to the devices’s operating instructions for details.

*1:

Steps are based on iOS 6.0.1.

Playing back music files on the

DLNA server

You can share music files stored in the DLNA Certified

media server (PC with Windows 7 installed, smartphone,

etc.) connected to your home network, and enjoy the

contents with this system’s speaker.

Preparation

• Complete the network settings. (> 6)

• Connect your device with DMC (Digital Media

Controller) compatible software installed to the same

home network as this system.

• Add the contents and folder to the libraries of the

Windows Media

Player or the smartphone, etc.

– Playlist of Windows Media

Player can play back only

the contents that are stored in the libraries.

1 Turn this system on.

• Check that “ ” is indicated on the display.

• If it doesn’t be indicated, check the network

settings. (> 6)

2 Operate the DMC compatible device and connect

to this system.

• The device name of this system will be displayed

as “Panasonic PMX9 _ _ _ _ _ _”*

1, 2

• For details on how to use DMC compatible

devices, refer to the operating instructions of the

devices or the software.

∫ Support format of DLNA client

File formats that are not supported by your DLNA server

cannot be played.

• Depending on the contents and the connected equipment,

playback may not be possible.

*1: “ _ ” stands for a digit that is unique to each set.

*2: The name that is displayed for this system can be

changed from the “Edit STEREO SYSTEM name”

settings. (

9, “Advanced network settings”)

Directly streaming to this system

(AirPlay)

“PW _ _ _ _ _”*

is displayed.

The 5 digits after “PW” is the password for this

network.

PMX9

Display the password

Change the password

Audio codec Example of file extension

MP3 .mp3

WAV .wav

FLAC .flac

SC-PMX9EG-VQT4Z21.book 10 ページ２０１３年３月２２日　金曜日　午後４時５４分

ENGLISH

VQT4Z21

Bluetooth

operations

By using the Bluetooth

connection, you can listen to the

sound from the Bluetooth

audio device from this system

wirelessly.

Refer to the operating instructions of the Bluetooth

device for details.

Preparation

• Turn on the Bluetooth

feature of the device and place

the device near this system.

• If this system is already connected to a Bluetooth

device, disconnect it.

1 Press [SELECTOR] repeatedly to select

“BLUETOOTH”.

If “Pairing” is indicated on the display, go to step 3.

2 Press [PLAY MENU] to select “New Device” and

then press [OK].

“Pairing” is indicated on the display.

3 Select “SC-PMX9” from the Bluetooth

device’s

Bluetooth

menu.

4 Start play on the Bluetooth

device.

Note:

• If prompted for the passkey, input “0000”.

• You can register up to 8 devices with this system. If a 9th

device is paired, the device that has not been used for the

longest time will be replaced.

Preparation

• Turn on the Bluetooth

feature of the device and place

the device near the speakers.

• If this system is already connected to a Bluetooth

device, disconnect it.

1 Press [SELECTOR] repeatedly to select

“BLUETOOTH”.

“Ready” is indicated on the display.

2 Select “SC-PMX9” from the Bluetooth

device’s

Bluetooth

menu.

The name of the connected device is indicated on

the display for 2 seconds.

3 Start play on the Bluetooth

device.

Note:

• This system can only be connected to one device at a time.

• When “BLUETOOTH” is selected as the source, this

system will automatically try and connect to the last

connected Bluetooth

device.

• The Bluetooth

device will be disconnected if a different

audio source (e.g., “CD”) is selected.

You can change the transmission speed to prioritize

transmission quality or sound quality.

Preparation

•

Press [SELECTOR] repeatedly to select “BLUETOOTH”.

• If a Bluetooth

device is already connected, disconnect

it.

1 Press [PLAY MENU] repeatedly to select

“Link Mode”.

2 Press [2, 1] to select the mode and then press

[OK].

Mode 1: Emphasis on connectivity

Mode 2: Emphasis on sound quality

If the sound input level of the Bluetooth

transmission is

too low, change the input level setting.

Preparation

• Connect a Bluetooth

device.

Press [PLAY MENU] repeatedly to select “Input Level”.

Press [

2, 1]

to select the level and then press [OK].

“Level 0” ,. “Level i1” ,. “Level i2”

^--------------------------------------J

Note:

• Select “Level 0” if the sound is distorted.

1 While a Bluetooth

device is connected:

Press [PLAY MENU] to select “Disconnect?”.

Press [

2, 1]

to select “OK? Yes” and then press

[OK].

About Bluetooth

Frequency band used

• This system uses the 2.4 GHz frequency band.

Certification of this device

• This system conforms to frequency restrictions and

has received certification based on frequency laws.

Thus, a wireless permit is not necessary.

• The actions below are punishable by law in some

countries:

- Taking apart or modifying this system.

- Removing specification indications.

Restrictions of use

• Wireless transmission and/or usage with all Bluetooth

equipped devices is not guaranteed.

• All devices must conform to standards set by Bluetooth

SIG, Inc.

• Depending on the specifications and settings of a

device, it can fail to connect or some operations can be

different.

• This system supports Bluetooth

security features. But

depending on the operating environment and/or

settings, this security is possibly not sufficient.

Transmit data wirelessly to this system with caution.

• This system cannot transmit data to a Bluetooth

device.

Range of use

• Use this device at a maximum range of 10 m.

The range can decrease depending on the

environment, obstacles or interference.

Interference from other devices

• This system may not function properly and troubles

such as noise and sound jumps may arise due to radio

wave interference if this system is located too close to

other Bluetooth

devices or the devices that use the

2.4 GHz band.

• This system may not function properly if radio waves

from a nearby broadcasting station, etc. is too strong.

Intended usage

• This system is for normal, general use only.

• Do not use this system near an equipment or in an

environment that is sensitive to radio frequency

interference (example: airports, hospitals, laboratories,

etc).

Pairing Bluetooth

devices

Connecting a paired Bluetooth

device

Bluetooth

transmission mode

• The default setting is “Mode 1”.

• To enjoy a higher sound quality, select “Mode 2”.

Bluetooth

input level

Disconnecting a Bluetooth

device

Panasonic bears no responsibility for data and/or

information that is compromised during a

wireless transmission.

SC-PMX9EG-VQT4Z21.book 11 ページ２０１３年３月２２日　金曜日　午後４時５４分

VQT4Z21

ENGLISH

Media Playback operations

The following marks indicate the availability of the

feature.

Preparation

• Turn the unit on.

• Insert the media or connect the Bluetooth

device.

• Press [CD], [iPod] or [SELECTOR] to select the audio

source.

Note:

• Depending on the model (e.g., iPod nano 7th generation,

etc.), it may be necessary to select the album, artist, etc. on

the iPod/iPhone.

• Operation results may vary depending on the iPod/iPhone/

iPad models.

• Tracks can be selected by pressing the numeric buttons.

Press [DISPLAY].

Note:

• Maximum characters that can be shown:

approximately 32

• This system supports ver. 2.3 ID3 tags.

• Text data that the system does not support can show

differently.

1 Press [PLAY MENU] to select “Repeat”,

“Random” or “PLAYMODE”.

2 Press [2, 1] and then press [OK] to select the

desired mode.

Note:

• During random playback, you cannot skip to tracks which

have been played or press the numeric buttons.

• Playmode function does not work with “Programme

playback”.

• [CD]

The setting returns to the default “Off” when you open

the disc tray.

[AirPlay] : The applied settings will remain until it is

changed.

*1: [AirPlay] : Perform the settings during playback.

[CD]: CD audio in CD-DA format and a CD that

contains MP3 files

[iPod]: Compatible iPod/iPhone/iPad

[USB]: USB devices containing MP3/FLAC files

[AirPlay] : When connected to an AirPlay compatible

device. (> 9)

[Bluetooth]:

Connected Bluetooth

device

Basic play [CD] [iPod] [USB] [AirPlay] [Bluetooth]

Play Press [1/;].

Stop Press [∫].

•

[USB]

: A track being played back is

memorised, and “Resume” is

displayed. The playback position

returns to the beginning of the track.

• [USB]: Press [∫] two times to stop

the playback fully.

Pause Press [1/;].

Press again to continue playback.

Skip Press [:] or [9] to skip track.

(main unit: [:/6] or [5/9])

[CD] [USB]: Press [3] or [4] to skip

the MP3/FLAC album.

(Except [AirPlay])

During play or pause

Press and hold [6] or [5].

(main unit: [:/6] or [5/9])

• [iPod]: Backwards search is only

within the current track.

[iPod]

View iPod menu

Press [iPod MENU].

[iPod]

Select an item

Press [3, 4] and then press [OK].

Viewing available information [CD] [USB]

[Bluetooth]

eg. MP3 : Track : Album

TAG: ID3 tags

Play menu [CD] [USB] [AirPlay]*1

[CD] [USB] Repeat

Off Select to cancel repeat playback.

1-Track Only plays the selected track.

•“1TR, `” is displayed.

(Skip to the desired track.)

All All tracks are repeated.

•“`” is displayed.

[AirPlay] Repeat

Refer to the connected device to verify the selected

setting.

[CD] [USB] Random

On Plays the contents randomly.

• “RND” is displayed.

• “RND” will not be displayed when

“1-Track” is selected.

Off Random playback is turned off.

[AirPlay] Shuffle

Refer to the connected device to verify the selected

setting.

[CD] (MP3) [USB] PLAYMODE

All Play all MP3/FLAC tracks.

1-Album Only plays the selected MP3/FLAC

album.

• “1ALBUM” is displayed.

SC-PMX9EG-VQT4Z21.book 12 ページ２０１３年３月２２日　金曜日　午後４時５４分

ENGLISH

VQT4Z21

This function allows you to programme up to 24 tracks.

[CD] (CD-DA)

1 Press [PROGRAM] in the stop mode.

“PGM” is shown.

2 Press the numeric buttons to select the desired

track.

Do this step again to programme other tracks.

3 Press [1/;] to start playback.

[CD] (MP3), [USB]

1 Press [PROGRAM] in the stop mode.

“PGM” is shown.

2 Press [3, 4] to select the desired album.

3 Press [9] and then press the numeric buttons

to select the desired track.

4 Press [OK].

Do steps 2 through 4 again to programme other

tracks.

5 Press [1/;] to start playback.

Note:

• The programme memory is cleared when you open the

disc tray.

Radio

30 FM stations can be preset.

Preparation

Press [SELECTOR] repeatedly to select “FM”.

1 Press [RADIO MENU] to select “Auto Preset”.

2 Press [2, 1] to select “Lowest” or “Current”

frequency.

3 Press [OK] to start presetting.

To cancel, press [∫].

1 Press [6] or [5] to tune in to the station.

To tune automatically, press and hold the button until

the frequency starts changing quickly.

2 Press [PROGRAM].

3 Press the numeric buttons to select a preset

number.

Do steps 1 through 3 again to preset more stations.

The new station replaces any station that occupies

the same preset number.

Press the numeric buttons, [:] or [9] (main

unit: [:/6] or [5/9]) to select the preset

station.

1 Press [RADIO MENU] repeatedly to select “FM

Mode”.

2 Press [2, 1] to select “Mono” and then press

[OK].

To cancel, select “Stereo”.

“Mono” is also cancelled when you change the

frequency.

To memorise the setting

Continue with steps 2 and 3 of “Manual tuning and

presetting”.

This system can show the text data transmitted by the

radio data system (RDS) available in some areas.

Press [DISPLAY].

Note:

• RDS may not be available if reception is poor.

Clock and timers

This is a 24-hour clock.

1 Press [CLOCK/TIMER] to select “CLOCK”.

2 Within 10 seconds, press [3, 4] to set the time.

3 Press [OK].

Press [CLOCK/TIMER] to show the clock for a few

seconds.

Note:

• Reset the clock regularly to maintain accuracy.

The sleep timer switches off the system after the set

time.

Press [SLEEP] repeatedly to select the setting (in

minutes).

To cancel, select “Off”.

To show the remaining time

Press [SLEEP].

Note:

• The sleep timer can be used together with the play timer.

• The sleep timer always comes first. Be sure not to set an

overlap of timers.

Programme playback [CD] [USB]

Cancel

programme

mode

Press [PROGRAM] in the stop

mode.

Check

programme

contents

Press [:] or [9] when “PGM” is

shown in the stop mode.

Clear the last

track

Press [DEL] in the stop mode.

Clear all

programmed

tracks

Press [∫] in the stop mode. “CLR

All” is shown. Within 5 seconds,

press [∫] again.

Automatic presetting

Manual tuning and presetting

Selecting a preset station

Improving the sound quality

RDS broadcasting

PS Programme service

PTY Programme type

FREQ Frequency

Setting the clock

Sleep timer

30min > 60min > 90min > 120min > Off

^-----------------------------------------------------------b

SC-PMX9EG-VQT4Z21.book 13 ページ２０１３年３月２２日　金曜日　午後４時５４分

VQT4Z21

ENGLISH

You can set the timer to come on at a certain time to

wake you up.

Preparation

Set the clock.

1 Press [CLOCK/TIMER] repeatedly to select

“TIMER Adjust”.

2 Within 8 seconds, press [3, 4] to set the start

time.

3 Press [OK].

4 Do steps 2 and 3 again to set the end time.

To start the timer

1 Prepare the audio source you want to listen to

and set the volume.

2 Press [F, PLAY].

“F” is shown.

To cancel, press [F, PLAY] again.

The system must be switched off for the timer to

operate.

To check the settings

Press [CLOCK/TIMER] repeatedly to select “TIMER

Adjust”.

Note:

• The timer starts at a low volume and increases gradually to

the preset level.

• The timer comes on at the set time every day if the timer is

on.

• If you switch off the system and switch on again while a

timer is in operation, the timer will not stop at the end time.

Sound effects

Press [SOUND] to select a sound effect.

2 Press [2, 1] to select the desired setting.

By main unit only

Turn [BASS] or [TREBLE] to adjust the level.

Press [PRESET EQ] to select a setting.

This function lets you enjoy a powerful bass effect.

Press [D.BASS] to select “On D.BASS” or “Off

D.BASS”.

Using the auxiliary input

You can connect a VCR, DVD player etc. and listen to

the audio through this system.

Preparation

Connect the external equipment.

1 Press [SELECTOR] repeatedly to select “AUX”.

2 Play the external equipment.

Others

Press [SETUP] to select “Dimmer”.

2 Press [2, 1] to select “On” and then press [OK].

Note:

• To cancel, select “Off” in step 2.

This function switches off the system (except in radio

source) if you do not use the system for approximately

20 minutes.

1 Press [SETUP] repeatedly to select “Auto Off”.

2 Press [2, 1] to select “On” and then press [OK].

Note:

• To cancel, select “Off” in step 2.

• When connected to a Bluetooth

device, this function does

not work.

• If “Net Standby” is set to “On”, this function will also be set

to “On”. To change the setting, set “Net Standby” to “Off”.

(> 15)

Occasionally, Panasonic may release updated software

for this system that may add or improve the way a

feature operates. These updates are available free of

charge.

Preparation

• Turn this system on.

• Connect this system to the home network. (> 6)

– Make sure that the network is connected to the

Internet.

– If “D.Connect” is set to “On”, change the setting to

“Off” and connect this system to a network that is

connected to the Internet.

Play timer

Changing the sound quality

BASS

-4 to +4

TREBLE

Surround “On Surround” or “Off Surround”

Preset EQ

Heavy Adds punch to rock

Soft For background music

Clear Clarifies higher frequencies

Vocal Adds gloss to vocal

Flat Cancels the sound effect

D.BASS

Decrease the brightness of the display panel

Automatically switch off the system

Software update

DO NOT DISCONNECT the AC mains lead while

one of the following messages is displayed.

– “Linking”, “Updating” or “%”

(“  ” stands for a number.)

• During the update process, no other operations can be

performed.

SC-PMX9EG-VQT4Z21.book 14 ページ２０１３年３月２２日　金曜日　午後４時５４分

ENGLISH

VQT4Z21

1 Press [SETUP] repeatedly to select “SW Update”

and then press [OK].

2 Press [2, 1] to select “Update? Yes” and then

press [OK] to start the update.

• Select “Update? No” to cancel the update.

{. After the update has finished, “Success” is displayed.

3 Disconnect the AC mains lead and reconnect it

after 3 minutes.

• If there are no updates, “No Need” is displayed.

≥ Downloading will require several minutes. It may take

longer or may not work properly depending on the

connection environment.

∫ Checking the software version

1 Press [SETUP] repeatedly to select “SW Version” and then

press [OK].

{. The version of the installed software is displayed.

2 Press [OK] to exit.

To check the Wi-Fi signal strength where this system is

located.

Preparation

Connect this system to the wireless network. (> 6)

1 Press [SETUP] repeatedly to select “Signal

Level” and then press [OK].

• This system’s displays show “Level ”.

(“  ” stands for a number.)

2 Press [OK] to exit this display mode.

• It is recommended to have a signal strength of “3”. Change

the position or angle of your wireless network router or this

system if the indication is “2” or “1” and see if the

connection improves.

• If “Level 0” is displayed, this system cannot establish a link

with the wireless network router. (> 17)

• This function does not work when “D.Connect” is set to

“On”.

The wireless LAN function can be enabled or disabled.

1 Press [SETUP] repeatedly to select

“Wireless LAN” and then press [OK].

2 Press [2, 1] to select “On” or “Off” and then

press [OK].

• The factory preset is “On”.

This system can turn on automatically from standby

mode when this system is selected as the AirPlay

speakers.

Preparation

Connect this system to the home network. (> 6)

1 Press [SETUP] repeatedly to select

“Net Standby” and then press [OK].

2 Press [2, 1] to select “On” and then press [OK].

• To cancel this function, select “Off” in step 2.

• The factory preset is “Off”. If this function is set to “On” the

standby power consumption will increase.

Display the name for the connected wireless network

(SSID).

1 Press [SETUP] repeatedly to select “Net Info”

and then press [OK].

“IP Addr.” is indicated on the display.

2 Press [SETUP] repeatedly to select “SSID” and

then press [OK].

3 Press [OK] to exit.

• If “No Connect” is displayed this system is not connected to

a wireless network.

• All letters are displayed as capital letters, and characters

that cannot be displayed are replaced with “

¢”.

To check this system’s IP address or the Wi-Fi MAC

address.

1 Press [SETUP] repeatedly to select “Net Info”

and then press [OK].

“IP Addr.” is indicated on the display.

2 Press [SETUP] repeatedly to select “IP Addr.” or

“MAC Addr.” and then press [OK].

The IP address or the MAC address is partially

displayed.

3 Press [2, 1] on the remote control to show the

rest of the IP address or the MAC address.

• To exit the setting, wait 20 sec.

• The “ – ” displayed on the top or bottom left of the display

indicate the first and last units respectively.

Wi-Fi signal strength

Wireless LAN setting

Network standby

Wireless network name (SSID)

IP/MAC Address

SC-PMX9EG-VQT4Z21.book 15 ページ２０１３年３月２２日　金曜日　午後４時５４分

VQT4Z21

ENGLISH

Troubleshooting

Before requesting service, make the following checks. If

you are in doubt about some of the check points, or if the

solutions indicated do not solve the problem, consult

your dealer for instructions.

Do you have the latest software installed?

• Occasionally, Panasonic may release updated

software for this system that may add or improve the

way a feature operates. (> 14)

No operations can be done with the remote control.

• Examine that the battery is installed correctly.

Sound is distorted or no sound.

• Adjust the volume of the system.

• Switch off the system, determine and correct the cause, then

switch the system on again. It can be caused by straining of

the speakers through excessive volume or power, and when

using the system in a hot environment.

A “humming” sound can be heard during playback.

• An AC mains lead or fluorescent light is near the

cables. Keep other appliances and cords away from

the cables of this system.

Display not shown correctly.

Playback does not start.

• You have not put in the disc correctly. Put it in correctly.

• Disc is dirty. Clean the disc.

• Replace the disc if it is scratched, warped, or

non-standard.

•

There is condensation. Let the system dry for 1 to 2 hours.

Reception is poor or a beat sound is heard.

• Keep the antenna away from computers, TVs, other

cables and cords.

• Use an outdoor antenna.

• Switch off the TV or move it away from the system.

You cannot switch on the iPod/iPhone/iPad.

• Examine that the battery of the iPod/iPhone/iPad is not

depleted.

• Switch off the iPod/iPhone/iPad and the system before

you connect the iPod/iPhone/iPad. Connect the iPod/

iPhone/iPad and try again.

No sound.

• Switch off the iPod/iPhone/iPad and remove from the

system. Connect the iPod/iPhone/iPad to the system

and switch it on and play it again.

iPod/iPhone/iPad does not charge.

• Examine the connection.

•

Charging an iPod/iPhone/iPad whose battery is depleted:

- When using the “iPod_Port” connection, turn this system

on. Do not turn this system off until the iPod/iPhone/iPad

becomes operational.

- When using the “iPod_Dock” connection, “Checking

Connection” will be displayed until the iPod/iPhone

becomes operational, but this system will have begun

charging.

The USB device or the contents in it cannot be read.

• The format of the USB device or the contents in it is/

are not compatible with the system.

• USB devices with storage capacity of more than 32 GB

cannot work in some conditions.

Slow operation of the USB device.

• Large content size or large memory USB device takes

longer time to read.

The elapsed time shown is different from the actual

play time.

• Transfer the data to another USB device or backup the

data and reformat the USB device.

Pairing cannot be done.

• Check the Bluetooth

device condition.

The device cannot be connected.

• The pairing of the device was unsuccessful or the

registration has been replaced. Try pairing the device

again.

• This system might be connected to a different device.

Disconnect the other device and try pairing the device

again.

The device is connected but audio cannot be heard

through this system.

• For some built-in Bluetooth

devices, you have to set

the audio output to “SC-PMX9” manually. Read the

operating instructions for the device for details.

The sound is interrupted.

• The device is out of the 10 m communication range.

Bring the Bluetooth

device closer to this system.

• Remove any obstacle between this system and the

device.

• Other devices that use the 2.4 GHz frequency band

(wireless router, microwaves, cordless phones, etc.)

are interfering. Bring the Bluetooth

device closer to

this system and distance it from the other devices.

• Select “Mode 1” for stable communication. (> 11)

Cannot connect to the network.

• Confirm the network connection and settings. (> 6)

• Your wireless network might be set to be invisible. In

this case select “Manual settings” in “Method 4”. (> 9)

• This system cannot join a wireless network using WEP

security settings with the WPS methods (“Method 1”).

Use “Method 4” to join the wireless network. (> 8)

• Make sure that the multicast function on the wireless

network router is set to on (enabled).

• When “D.Connect” is used, if the password for

“D.Connect” has been changed connect the other

device to this system using the new password. (> 10)

• Check that “Wireless LAN” is set to “On”. (> 15)

Cannot connect to this system.

• Display the wireless network name that this system is

connected to and make sure that the device is

connected to the same network. (> 6, 15)

• If “Net Standby” is set to “Off”, the AirPlay compatible

device cannot be connected when this system is off.

• Turn off the Wi-Fi setting on the AirPlay compatible

device, set “Net Standby” to “Off” (> 15) and then turn

this system off and on. Reconnect the compatible

device to the Wi-Fi network and then select this system

as the AirPlay speakers again.

Common problems

Disc

Radio

iPod/iPhone/iPad

USB

Bluetooth

AirPlay operations

SC-PMX9EG-VQT4Z21.book 16 ページ２０１３年３月２２日　金曜日　午後４時５４分

ENGLISH

VQT4Z21

My wireless network router is WPS PBC compatible,

but the pairing does not work.

• If the network is set to be invisible, the push button

configuration does not work. In this case, either make

the wireless network visible while you set up the

network for this system or use “Method 2”, “Method 3”

or “Method 4”. (> 7, 8)

Playback does not start.

The sound is interrupted.

• Try a wired LAN connection. (> 6)

• Simultaneous use with other 2.4 GHz devices, such as

microwaves, cordless telephones, etc., may result in

connection interruptions.

Increase the distance between this system and these

devices.

• Do not place this system inside a metal cabinet, for it

might block the Wi-Fi signal.

• Place this system closer to the wireless network router.

• If “D.Connect” is set to “On”, place the AirPlay

compatible device closer to the speakers.

• If several wireless devices are simultaneously using

the same wireless network as this system, try turning

off the other devices or reducing their wireless network

usage.

• If the playback stops, check the playback status on the

iOS device or iTunes.

• If play does not start (even though “ ” is displayed),

restart the wireless network router, turn the Wi-Fi

connection on the iOS device or Mac/PC off and on,

and then make sure that your home wireless network

is selected.

• With some iOS and iTunes versions, it may not be

possible to restart the AirPlay playback if the selector is

changed (e.g., “CD”) or this system is turned off, during

the AirPlay playback.

In this case, select a different device from the AirPlay

icon of the Music App or iTunes and then re-select this

system as the output speakers. (> 9)

“--:--”

• You connected the AC mains lead for the first time or

there was a power failure recently. Set the clock.

“Adjust CLOCK”

• Clock is not set. Adjust the clock accordingly.

“Adjust TIMER”

• Play timer is not set. Adjust the play timer accordingly.

“Auto Off”

•

The unit has been left unused for about 20 minutes and will

shut down in a minute. Press any button to cancel it.

“CANNOT SET”

• Select an audio source other than “AirPlay”,

“BLUETOOTH” or “DLNA”.

“Checking Connection”

• The unit is checking the connected iPod/iPhone/iPad.

If this display keeps appearing, make sure that iPod/

iPhone/iPad is inserted correctly and try again.

“DL Error”

• The software download has failed. Press any button to

exit. Please try again later.

• The server cannot be found. Press any button to exit. Make

sure that the wireless network is connected to the Internet.

“Error”

• An incorrect operation was done. Read the instructions

and try again.

“F61” or “F76”

• There is a power supply problem.

“Fail”

• Updating or setting has failed. Read the instructions

and try again.

“iPod_Dock Over Current Error”

“iPod_Port Over Current Error”

• The iPod/iPhone/iPad or USB device is drawing too

much power. Remove the iPod/iPhone/iPad or USB

device. Switch the system off and on again.

“Level 0”

• There is no link between this system and the wireless

network router.

Try the following operations:

– Check that the wireless network router is turned on.

– Turn this system off and on again.

– Reset the wireless network settings. (> 6)

If the problem persists, consult your dealer.

“Level j”

• When “D.Connect” is set to “On” the Wi-Fi signal

strength cannot be checked. To check the Wi-Fi signal

strength from the wireless network router, set

“D.Connect” to “Off”. (> 10)

“Linking”

• This system is communicating with the wireless

network router to complete the network settings.

Depending on the wireless network router this process

may take a few minutes. Try moving this system closer

to the wireless network router.

“No Connect”

• This system cannot connect to the network.

Check the network connection. (> 6)

“No Device”

• The iPod/iPhone/iPad or USB device is not connected.

Examine the connection.

“No Disc”

• You have not put in a disc or put in a disc that the

system cannot play.

“No Play”

• Examine the content. You can only play supported

format.

• If there are more than 255 albums or folders (audio

and non-audio), some of the MP3/FLAC files in these

albums cannot be read and played. Transfer these

music albums to another USB device. Alternatively,

reformat the USB device and save these music albums

prior to saving the other non-audio folders.

“Not MP3/Error”

• An unsupported MP3 format. The system will skip that

track and play the next one.

“Not Supported”

• You have inserted an iPod/iPhone/iPad that cannot be

played.

• Switch off the iPod/iPhone/iPad and the system before

you connect the iPod/iPhone/iPad. Connect the iPod/

iPhone/iPad and try again.

• This message may be displayed when a wireless LAN

connection is made without unlocking the iPod/iPhone/

iPad. (> 7, “Method 2”)

“PGM Full”

• The number of programmed tracks is more than 24.

“Reading”

• The unit is checking the disc and USB device

information. After this display has disappeared, start

operating.

“Set Wi-Fi”

• The connected iPod touch/iPhone/iPad is not

connected to a wireless network. Connect it to a

wireless network and try again. (> 6)

“Wait”

• This is displayed, for example, when this unit is turned

off. (For up to 1 minute and 30 seconds)

Main unit displays

SC-PMX9EG-VQT4Z21.book 17 ページ２０１３年３月２２日　金曜日　午後４時５４分

VQT4Z21

ENGLISH

Reset the memory when the following situations occur:

• There is no response when buttons are pressed.

• You want to clear and reset the memory contents.

1 Disconnect the AC mains lead.

Wait 3 minutes before you continue with step 2.

2 While you press and hold [Í/I] on the main unit,

connect the AC mains lead again.

“- - - - - - - - - - - -” is shown.

3 Release [Í/I].

All the settings are set back to the factory preset.

It is necessary to set the memory items again.

When other Panasonic equipment responds to the

remote control of this system, change the remote control

code for this system.

To set the code to “Remote 2”

1 Press [CD] to select “CD”.

2 Press and hold [CD] on the main unit and [2] on

the remote control until “Remote 2” is shown.

3 Press and hold [OK] and [2] for a minimum of

4 seconds.

• The factory preset is “Remote 1”.

• To change the mode back to “Remote 1”, repeat the

steps above but replace the button pressed on the

remote control from [2] to [1].

Specifications

RMS output power

Front Ch (both ch driven)

60 W per channel (3 ™), 1 kHz,

10% total harmonic distortion

Total RMS power 120 W

Frequency modulation (FM)

Preset memory 30 stations

Frequency range

87.50 MHz to 108.00 MHz (50 kHz step)

Antenna terminals 75 ™ (unbalanced)

“iPod_Port” connection

DCOUT 5V 2.1A (max)

USB standard USB 2.0

Media file format support MP3 (*.mp3)

, FLAC (*.flac)

USB device file system FAT16, FAT32

ID3 Tag support v2.3

“iPod_Dock” connection

DCOUT 5V 1.0A (max)

Headphones jack Stereo, Ø 3.5 mm jack

AUX input (rear) Pin jack

LAN port 10 Base-T/100 Base-TX

Disc played (8 cm or 12 cm)

CD, CD-R/RW (CD-DA, MP3)

Pick up

Wavelength 790 nm (CD)

Laser power CLASS 1

NORSK

Bølgelengde 790 nm (CD)

Laserstyrke Ingen farlig stråling sendes ut

Audio output (Disc)

Number of channels 2 ch (FL, FR)

Speaker unit(s)

Woofer 14 cm cone type x 1

Tweeter 1.9 cm dome type x 1

Super tweeter 1.2 cm piezo type x 1

Impedance 3™

Dimensions (W x H x D) 161 mm x 238 mm x 264 mm

Mass Approx. 3.0 kg

Bluetooth

system specification V3.0

Wireless equipment classification Class 2

Supported profiles A2DP

Frequency band 2.4 GHz band FH-SS

Driving distance 10 m Line of sight

Prospective communication distance

Measurement environment:

Temperature 25 oC / Height 1 m

Measure in “Mode 1”

MP3

Sampling frequency 32/44.1/48 kHz

Audio word size 16 bits

Channel count 2 ch

Bit-rate 8-320 kbps

FLAC

Sampling frequency

32/44.1/48/88.2/96/176.4/192 kHz

Audio word size 16.24 bits

Channel count 2 ch

WAV (DLNA only)

Sampling frequency

32/44.1/48/88.2/96/176.4/192 kHz

Audio word size 16.24 bits

Channel count 2 ch

Memory reset (initialisation)

Remote control code

Amplifier section

Tuner section

Terminals section

Disc section

Speaker section

Bluetooth

section

Wi-Fi/AirPlay section

Wi-Fi

WLAN Standard IEEE802.11b/g

Frequency range 2.4 GHz band

Security WEP (64 bit/128 bit),

WPA

, WPA2

WPS version

Version 2.0 (WEP not support)

Audio Support format (USB, DLNA)

SC-PMX9EG-VQT4Z21.book 18 ページ２０１３年３月２２日　金曜日　午後４時５４分

ENGLISH

VQT4Z21

Power supply AC 220 V to 240 V, 50 Hz

Power consumption 60 W

Dimensions (W x H x D) 210 mm x 120 mm x 266 mm

Mass Approx. 3.1 kg

Operating temperature range 0°C to +40°C

Operating humidity range

35% to 80% RH (no condensation)

Note:

• Specifications are subject to change without notice. Mass

and dimensions are approximate.

• Total harmonic distortion is measured by the digital

spectrum analyzer.

FLAC Decoder

Josh Coalson

Redistribution and use in source and binary forms, with or

without modification, are permitted provided that the following

conditions are met:

- Redistributions of source code must retain the above

disclaimer.

- Redistributions in binary form must reproduce the above

disclaimer in the documentation and/or other materials

provided with the distribution.

- Neither the name of the Xiph.org Foundation nor the

names of its contributors may be used to endorse or

promote products derived from this software without

specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT

HOLDERS AND CONTRIBUTORS “AS IS” AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE

FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,

OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS

OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR

BUSINESS INTERRUPTION) HOWEVER CAUSED AND

ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY

OUT OF THE USE OF THIS SOFTWARE, EVEN IF

ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

General

Power consumption in standby mode

(

When the iPod/iPhone/iPad is not charging)

0.4 W (approximate)

Declaration of Conformity (DoC)

Hereby, “Panasonic Corporation” declares that this product

is in compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Customers can download a copy of the original DoC to our

R&TTE products from our DoC server:

http://www.doc.panasonic.de

Contact to Authorised Representative:

Panasonic Marketing Europe GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525

Hamburg, Germany

This product is intended for general consumer. (Category 3)

This product on purpose to connect to access point of 2.4 GHz

WLAN.

Disposal of Old Equipment and Batteries

Only for European Union and countries with

recycling systems

These symbols on the products,

packaging, and/or accompanying

documents mean that used electrical

and electronic products and batteries

must not be mixed with general

household waste.

For proper treatment, recovery and

recycling of old products and used

batteries, please take them to applicable

collection points in accordance with your national

legislation.

By disposing of them correctly, you will help to save

valuable resources and prevent any potential negative

effects on human health and the environment.

For more information about collection and recycling,

please contact your local municipality.

Penalties may be applicable for incorrect disposal of

this waste, in accordance with national legislation.

Note for the battery symbol (bottom

symbol):

This symbol might be used in

combination with a chemical symbol. In

this case it complies with the

requirement set by the Directive for the

chemical involved.

SC-PMX9EG-VQT4Z21.book 19 ページ２０１３年３月２２日　金曜日　午後４時５４分

VQT4Z21

POLSKI

Opisane procedury należy wykonać za pomocą pilota

zdalnego sterowania. Można również użyć przycisków

na panelu przednim urządzenia, jeśli są identyczne.

Zakupione urządzenie może różnić się od

przedstawionego na ilustracjach.

Niniejsza instrukcja obsługi ma zastosowanie do

następującego zestawu.

Środki ostrożności

Urządzenie

• Aby ograniczyć niebezpieczeństwo pożaru, porażenia

prądem lub uszkodzenia urządzenia,

- Nie należy wystawiać urządzenia na działanie deszczu,

wilgoci, kapanie lub zachlapanie.

- Na urządzeniu nie należy umieszczać żadnych

przedmiotów napełnionych płynami, np. dzbanków.

-Należy stosować tylko zalecane akcesoria.

- Nie zdejmować pokrywy.

-Użytkownik nie powinien podejmować się naprawy

urządzenia na własną rękę. Serwis należy zlecić w

autoryzowanym punkcie serwisowym.

Urządzenie

• Aby ograniczyć niebezpieczeństwo pożaru, porażenia

prądem lub uszkodzenia urządzenia,

- Niniejszego urządzenia nie należy instalować lub umieszczać w

biblioteczce, wbudowanej szafce lub innej ograniczonej

przestrzeni. Należy zapewnić odpowiednią wentylację urządzenia.

-Nie zasłaniaj otworów wentylacyjnych urządzenia

gazetami, obrusami, zasłonami i podobnymi przedmiotami.

- Nie umieszczać na urządzeniu źródeł otwartego ognia,

jak np. zapalone świece.

•Urządzenie jest przeznaczone do używania w klimacie

umiarkowanym.

• Wtyczka zasilania umożliwia odłączenie urządzenia.

Zainstaluj to urządzenie w taki sposób, aby możliwe było

natychmiastowe odłączenie wtyczki zasilania od gniazda zasilania.

• To urządzenie może odbierać zakłócenia wywołane

użyciem telefonu komórkowego. Jeżeli takie zakłócenia

wystąpią, wskazane jest zwiększenie odległości pomiędzy

urządzeniem a telefonem komórkowym.

•Urządzenie wykorzystuje promień lasera. Sterowanie,

regulacje lub postępowanie w sposób tutaj nie określony

grozi niebezpiecznym naświetleniem promieniami lasera.

Bateria

• Nie wolno zwierać biegunów baterii ani jej rozbierać.

• Nie ładować baterii alkalicznych ani manganowych.

• Nie wolno używać baterii, z których została zdjęta warstwa

ochronna.

• Nie zbliżać baterii do źródeł ciepła lub ognia.

• Baterii nie należy pozostawiać przez dłuższy czas, w

pojeździe z zamkniętymi drzwiami i oknami, narażonym na

bezpośrednie promieniowanie słoneczne.

•Jeśli pilot ma nie być używany przez dłuższy czas, należy wyjąć z

niego baterię. Przechowywać w chłodnym, ciemnym miejscu.

• Istnieje niebezpieczeństwo wybuchu w przypadku, gdy

baterie zostaną nieprawidłowo założone. Baterie należy

wymieniać na takie same lub na baterie równorzędnego

typu, zalecane przez producenta.

•Zużyte baterie należy odpowiednio zutylizować. Właściwą

metodę powinny wskazać władze lokalne.

Android, Google Play oraz Chrome są znakami handlowymi firmy

Google Inc.

DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks,

service marks, or certification marks of the Digital Living Network

Alliance.

Logo Wi-Fi CERTIFIED jest znakiem zgodności z normą Wi-Fi

Alliance.

Wi-Fi Protected Setup jest znakiem towarowym stowarzyszenia

Wi-Fi Alliance.

“Wi-Fi”, “Wi-Fi Protected Setup”, “WPA” i “WPA2” są znakami

towarowymi lub zastrzeżonymi znakami towarowymi

stowarzyszenia Wi-Fi Alliance.

Technologia kodowania dźwięku MPEG Layer-3 na licencji firmy

Fraunhofer IIS i Thomson.

Nazwa marki Bluetooth

i logotypy są własnością firmy Bluetooth

SIG, Inc. I wszelkie ich użycie przez firmę Panasonic Corporation

jest objęte licencją.

Pozostałe znaki towarowe i nazwy handlowe są własnością ich

posiadaczy.

Windows jest znakiem towarowym lub zarejestrowanym znakiem

towarowym firmy Microsoft Corporation w Stanach Zjednoczonych

i w innych krajach.

Spis treści

Środki ostrożności ..........................................2

Dostarczone wyposażenie .............................. 3

Konserwacja.....................................................3

Przygotowanie pilota zdalnego sterowania

................. 3

Podłączenie ...................................................... 3

Rozmieszczenie głośników............................. 4

Opis elementów sterowania ........................... 4

Wsadzanie nośników....................................... 5

Informacje o nośnikach................................... 5

Ustawienia sieci ...............................................6

Używanie AirPlay z głośnikami systemu....... 9

Odtwarzanie plików muzycznych na serwerze DLNA.... 10

Operacje Bluetooth

...................................... 11

Informacje o Bluetooth

................................ 11

Operacje odtwarzania nośników .................. 12

Radio............................................................... 13

Zegar i timer ...................................................13

Efekty dźwiękowe .......................................... 14

Korzystanie z wejścia dodatkowego............14

Inne .................................................................14

Rozwiązywanie problemów .......................... 16

Dane techniczne ............................................ 18

“Made for iPod”, “Made for iPhone” oraz “Made for iPad” oznacza,

że urządzenie elektroniczne zostało specjalnie zaprojektowane do

współpracy odpowiednio z urządzeniem iPod, iPhone lub iPad i

spełnia normy wydajności firmy Apple.

Firma Apple nie jest odpowiedzialna za działanie tego urządzenia i

jego zgodność z normami bezpieczeństwa oraz innymi przepisami.

Używanie niniejszego urządzenia z urządzeniem iPod, iPhone lub

iPad może wpływać na wydajność pracy bezprzewodowej.

AirPlay, logo AirPlay, iPad, iPhone, iPod, iPod classic, iPod nano i

iPod touch są znakami towarowymi Apple Inc., zarejestrowanymi

w Stanach Zjednoczonych i innych krajach.

App Store jest znakiem usługowym firmy Apple Inc.

Zestaw SC-PMX9

Urządzenie

główne

SA-PMX9

Głośniki SB-PMX9

OSTRZEŻENIE!

UWAGA!

SC-PMX9EG-VQT4Z21.book 2 ページ２０１３年３月２２日　金曜日　午後４時５４分

Leht laadib ...

Panasonic SC-PMX9 Omaniku manuaal

Bränd: Panasonic

Mudel: SC-PMX9

Kategooria: CD-mängijad

Tüüp: Omaniku manuaal

See käsiraamat sobib ka

SCPMX9EG

Laadige alla PDF

aruanne

teistes keeltes

polski: Panasonic SC-PMX9 Instrukcja obsługi
slovenčina: Panasonic SC-PMX9 Návod na obsluhu
English: Panasonic SC-PMX9 Owner's manual

Panasonic SC-PMX9 Omaniku manuaal

See käsiraamat sobib ka

Panasonic SC-PMX9 Omaniku manuaal

teistes keeltes

Seotud paberid

Muud dokumendid