Jacobsen eclipse 2 InCommand Dealer's Manual

Kategooria
Muruniidukid
Tüüp
Dealer's Manual
When Performance Matters.
Eclipse
®
2
InCommand
63334 – Eclipse 2 118, 18” 11 Blade Reel, Gen-Set
63343 – Eclipse 2 118, 18” 11 Blade Reel, Battery Pack
63335 – Eclipse 2 118, 18” 15 Blade Reel, Gen-Set
63344 – Eclipse 2 118, 18” 15 Blade Reel, Battery Pack
63336 – Eclipse 2 118F, Floating 18” 11 Blade Reel, Gen-Set
63345 – Eclipse 2 118F, Floating 18” 11 Blade Reel, Battery Pack
63337 – Eclipse 2 118F, Floating 18” 15 Blade Reel, Gen-Set
63346 – Eclipse 2 118F, Floating 18” 15 Blade Reel, Battery Pack
63338 – Eclipse 2 122, 22” 11 Blade Reel, Gen-Set
63347 – Eclipse 2 122, 22” 11 Blade Reel, Battery Pack
63339 – Eclipse 2 122, 22” 15 Blade Reel, Gen-Set
63348 – Eclipse 2 122, 22” 15 Blade Reel, Battery Pack
63340 – Eclipse 2 122F, Floating 22” 11 Blade Reel, Gen-Set
63349 – Eclipse 2 122F, Floating 22” 11 Blade Reel, Battery Pack
63341 – Eclipse 2 122F, Floating 22” 15 Blade Reel, Gen-Set
63350 – Eclipse 2 122F, Floating 22” 15 Blade Reel, Battery Pack
63342 – Eclipse 2 126, 26” 7 Blade Reel, Gen-Set
63351 – Eclipse 2 126, 26” 7 Blade Reel, Battery Pack
WARNING
WARNING: If incorrectly used this machine can cause severe
injury. Those who use and maintain this machine should be
trained in its proper use, warned of its dangers and should
read the entire manual before attempting to set up, operate,
adjust or service the machine.
VAROITUS
VAROITUS: Koneen väärinkäyttö saattaa johtaa vakavaan
loukkaantumiseen. Tätä konetta käyttävillä ja huoltavilla henkilöillä on
oltava asianmukainen koulutus sen käyttöön. Heidän on tunnettava
sen vaarat ja luettava koko käyttöopas ennen koneen käyttöönottoa,
käyttöä, säätöä tai huoltoa.
4260474-FI-Rev B
Dealer Manual
Jälleenmyyjän opas
63334 – Eclipse 2 118, 457 mm:n 11-teräinen kela, yleisasetus
63343 – Eclipse 2 118, 457 mm:n 11-teräinen kela, akkuyksikkö
63335 – Eclipse 2 118, 457 mm:n 15-teräinen kela, yleisasetus
63344 – Eclipse 2 118, 457 mm:n 15-teräinen kela, akkuyksikkö
63336 – Eclipse 2 118F, kelluva 457 mm:n 11-teräinen kela, yleisasetus
63345 – Eclipse 2 118F, kelluva 457 mm:n 11-teräinen kela, akkuyksikkö
63337 – Eclipse 2 118F, kelluva 457 mm:n 15-teräinen kela, yleisasetus
63346 – Eclipse 2 118F, kelluva 457 mm:n 15-teräinen kela, akkuyksikkö
63338 – Eclipse 2 122, 559 mm:n 11-teräinen kela, yleisasetus
63347 – Eclipse 2 122, 559 mm:n 11-teräinen kela, akkuyksikkö
63339 – Eclipse 2 122, 559 mm:n 15-teräinen kela, yleisasetus
63348 – Eclipse 2 122, 559 mm:n 15-teräinen kela, akkuyksikkö
63340 – Eclipse 2 122F, kelluva 559 mm:n 11-teräinen kela, yleisasetus
63349 – Eclipse 2 122F, kelluva 559 mm:n 11-teräinen kela, akkuyksikkö
63341 – Eclipse 2 122F, kelluva 559 mm:n 15-teräinen kela, yleisasetus
63350 – Eclipse 2 122F, kelluva 559 mm:n 15-teräinen kela, akkuyksikkö
63342 – Eclipse 2 126, 660 mm:n 7-teräinen kela, yleisasetus
63351 – Eclipse 2 126, 660 mm:n 7-teräinen kela, akkuyksikkö
FI
Finland
This manual contains safety, operating, adjustment,
maintenance, troubleshooting instructions and parts list
for your new Jacobsen machine. This manual should be
stored with the equipment for reference during operation.
Before you operate your machine, you and each operator
you employ should read the manual carefully in its
entirety. By following the safety, operating and
maintenance instructions, you will prolong the life of your
equipment and maintain its maximum efficiency.
If additional information is needed, contact your
Jacobsen Dealer.
The serial plate is located on the rear crossbar of the
frame. Jacobsen recommends you record these numbers
below for easy reference.
11524 WILMAR BLVD,
CHARLOTTE, NC 28273
®
kg kW
1-800-848-1636 (US)
PRODUCT OF U.S.A.
A Textron Company
2
Proposition 65 Warning
This product contains or emits
chemicals known to State of California
to cause cancer and birth defects or
other reproductive harm.
FORWORD
Suggested Stocking Guide
To Keep your Equipment fully operational and productive, Jacobsen suggests you maintain a stock of the more
commonly used maintenance items. We have included part numbers for additional support materials and training aids.
To order any of the following material:
1. Write your full name and complete address on your
order form.
2. Explain where and how to make shipment:
?
UPS
?
Regular Mail
?
Overnight
?
2nd Day
3. Order by the quantity desired, the part number, and
the description of the part.
4. Send or bring the order to your authorized Jacobsen
Dealer.
© 2012, Jacobsen, A Textron Company/Textron Innovations Inc.
“All rights reserved, including the right to reproduce this material
or portions thereof in any form.”
These are the original instructions verified by
Jacobsen, A Textron Company.
LITHO IN U.S.A. 9-2014
Service Parts
Service Support Material
Qty. Part No. Description Qty. Part No. Description
4102780 50 Amp Fuse 2811106 Motor to Pulley Belt
4262910 25 Amp Fuse 2811070 Pulley to Traction Drum Belt
4131618 Ignition Key
Qty. Part No. Description
4260472 Technical Manual
4260475 Operator Training Video
4262930 Floating Head Service Manual
4262932 Fixed Head Service Manual
Qty. Part No. Description
3
> Change from previous revision
Table of Contents
1 Safety
1.1How to Operate Safely.......................................... 4
1.2 Important Safety Notes ..................................... 7
2 Controls
2.1 Icons................................................................. 8
2.2 Handle Controls ................................................ 8
2.3 LCD Display ..................................................... 9
2.4 Frequency of Cut ............................................ 14
2.5 Gas Power Module Controls .......................... 19
2.6 Battery Power Module Controls ...................... 19
3Set Up
3.1 General........................................................... 20
3.2 Initial inspection .............................................. 20
3.3 Operating Checks ........................................... 20
3.4 Interlock System (O.P.C.) ............................... 21
3.5 Transport Wheels (Optional) .......................... 21
4 Battery Power Module Set Up
4.1 Safety............................................................. 22
4.2 General ........................................................... 22
4.3 Batteries ......................................................... 23
4.4 Battery Installation .......................................... 24
4.5 Battery Charger .............................................. 25
4.6Replacing Battery Pack 26
5 Gas Engine Power Module Set Up
5.1 Engine............................................................ 27
5.2 Engine Oil ....................................................... 27
5.3 Engine Oil Change ......................................... 28
5.4 Engine Speed ................................................. 28
5.5 Fuel ................................................................ 29
6 Adjustments (All Units)
6.1 General........................................................... 30
6.2 Brake .............................................................. 30
6.3 Speed Paddle Stops ....................................... 30
6.4 Handle ............................................................ 31
6.5 Traction Belts ................................................. 31
6.6 Front Roller Weight ........................................ 32
6.7 Torque Specification ....................................... 33
7 Fixed Head Reel Adjustments
7.1 General .......................................................... 34
7.2 Reel To Bedknife ............................................ 34
7.3 Bedknife Adjustment ...................................... 35
7.4 Cutting Height ................................................ 35
8 Floating Head Reel Adjustments
8.1 General .......................................................... 36
8.2 Bedknife-To-Reel ........................................... 36
8.3 Bedknife Adjustment ...................................... 37
8.4 Reel Bearing .................................................. 37
8.5 Cutting Height ................................................ 38
8.6 Reel Assembly Removal ................................ 38
9 Troubleshooting
9.1 General .......................................................... 39
10 Maintenance & Lubrication Charts
10.1 General .......................................................... 40
10.2 Maintenance Chart ......................................... 40
10.3 Lubrication Chart............................................ 41
11 Notes
12 Pre Delivery Checklist
12.1 Pre-Delivery Checklist.................................... 43
1 SAFETY
4
1 SAFETY
1.1 HOW TO OPERATE SAFELY
SAFE OPERATION
a Read the Operator’s Manual and other training
material. If the operator or technician can not read
this manual, the owner is responsible to describe
this material to the operators and technicians.
Manuals in additional languages may be available
on the Jacobsen or RansomesJacobsen website.
a Read all of the instructions for this mower carefully.
Know the controls and the correct operation of the
equipment.
b Children or persons who do not understand these
instructions must not use the mower. The local
regulations can limit the age of the operator.
c Never use a mower near persons, including
children or animals.
d Remember that the operator or owner is
responsible for accidents or hazards that occur to
other persons or their property.
e Never carry passengers.
f Never allow persons to operate or service the
mower or its attachments without correct
instructions.
g Do not operate equipment while tired, sick or after
you use alcohol or drugs.
PREPARATION
a When you operate the mower, wear correct
clothing, slip resistant work shoes or boots, work
gloves, hard hat, safety glasses and hearing
protection. Long hair, loose clothing or jewelry can
be caught in moving parts.
b Do not operate the equipment with the Interlock
System disconnected or the system does not
operate correctly. Do not disconnect or prevent the
operation of any switch.
c Never operate equipment that is not in correct
order or without decals, guards, shields, deflectors
or other protective devices fastened.
d Inspect the mower before you operate the mower.
Check the tire pressure, engine oil level, the
radiator coolant level and the air cleaner indicator.
Fuel is flammable. Use caution when you add the
fuel to the mower.
e Operate the mower in daylight or in good artificial
light. Use caution when you operate the mower
during bad weather. Never operate the mower with
lightning in the area.
f Inspect the area to select the accessories and
attachments that are needed to correctly and safely
do the job. Only use parts, accessories and
attachments approved by Jacobsen.
g Be careful of holes in the terrain and other hazards
that are not visible.
h Inspect the area where the equipment is operated.
Remove all objects you can find before you
operate. Be careful of obstructions above the
ground (low tree limbs, electrical wires) and also
underground obstacles (sprinklers, pipes, tree
roots). Enter a new area carefully. Look for
possible hazards.
i Inspect the cutting system before you start the
mower. Make sure the blades are free to rotate.
When you rotate one blade, other blades can
rotate.
OPERATION
a Never operate the engine without enough
ventilation or in an enclosed area. The carbon
monoxide in the exhaust fumes can increase to
dangerous levels.
b Never carry passengers. Keep other persons or
animals away from the mower.
c Disengage all drives and engage the parking brake
before you start the engine. Only start the engine
with the operator in the seat. Never start the engine
with persons near the mower.
d Keep your legs, arms and body inside the operator
compartment while the mower is in operation.
Keep your hands and feet away from the cutting
units.
WARNING
EQUIPMENT OPERATED INCORRECTLY OR WITHOUT TRAINING CAN BE DANGEROUS.
Know the location and correct operation of controls. Operators without experience must receive instruction from
another person that knows the correct operation of the equipment before you operate the mower.
Only use parts, accessories and attachments approved by Jacobsen.
!
SAFETY 1
5
e Do not use on the slopes greater than the safe
slope limit for the equipment.
f To guard against over turning or loss of control:
Operate the mower across the face (horizontally),
but not up and down on the face of slopes
(vertically).
Do not start or stop suddenly on slopes.
Decrease the speed when you operate on slopes
or when you must turn. Use caution when you
change direction. Turf condition can change the
mower stability.
Use caution when you operate the mower near
drop-offs, ditches or embankments.
Be careful of holes in the terrain and other hazards
that are not visible.
g Always operate at speeds that allow you to have
complete control of the machine. Make sure of your
footing keep a tight grip the handle and walk.
Never run when you operate the mower.
h Use caution when you go near corners, trees or
other objects that can prevent a clear view.
i Equipment must meet the current regulations to be
driven on the public roads.
j Before you move across or operate on the paths or
roads, turn off the PTO switch, lift the mowers and
travel at decreased speed. Look for traffic.
k Stop the blades when the mower is on any surface
that is not grass.
l Do not release the cut grass in the direction of
persons or allow persons near the mower while in
operation.
m Do not operate the mower with damaged guards or
without safety devices in position.
n Do not change the engine governor setting or over-
speed the engine. Never change or tamper with
adjusters that are closed with a seal for the engine
speed control.
o Before you leave the operator compartment, for
any reason:
Disengage all the drives and lower attachments to
the ground.
Engage the parking brake.
Stop the engine and remove the key.
p When you hit an object or mower starts to cause
the vibration that is not normal, inspect the mower
for damage and make repairs.
q Decrease the throttle setting before you stop the
engine.
r Do not use this equipment for uses that the mower
was not made for.
SAFE HANDLING OF FUELS
a The fuel and the fuel vapors are flammable. Use
caution when you add the fuel to the mower. The
fuel vapors can cause an explosion.
b Never use the containers that are not approved to
keep or transfer fuel.
c Never keep the mower or fuel containers near an
open flame or any device that can cause the
ignition of fuel or fuel vapors.
d Never fill the fuel containers inside a vehicle or on
a truck or trailer with a plastic liner. Always put the
fuel container on the ground away from your
vehicle before you fill the container.
e Refuel the mower before you start the engine.
When the engine is in operation or while the engine
is hot, never remove the fuel cap or add fuel to the
mower.
f Refuel outdoors only and do not smoke when you
add fuel. Extinguish all types of ignition.
g The fuel nozzle must touch the rim of the fuel tank
when you add fuel to the mower. Do not use a
device to lock the fuel nozzle in the open position.
h Do not over fill the fuel tank. Leave at least 1 inch
(25 mm) below the filler neck.
i Always tighten the fuel tank cap and container cap
after you add fuel.
j If the fuel spills on your clothing, change your
clothing immediately.
MAINTENANCE AND STORAGE
a Before you clean, adjust or repair this equipment,
stop the engine and disconnect the spark plug
wire. Keep the wire away from the plug to prevent
the engine to start. Disconnect the power
connector
b Make sure the mower is parked on a solid and level
surface.
c Never work on a mower that is lifted only by the
jack. Always use the jack stands.
d Do not remove battery pack without unit on
kickstand.
e Never allow persons to service the mower or its
attachments without correct instructions.
1 SAFETY
6
f When the mower is parked, put into storage or left
without an operator, lower the cutting device unless
a positive mechanical lock is used.
g When you put the mower on a trailer or put the
mower in storage, close the fuel valve. Do not keep
fuel near flames or drain the fuel inside a building.
h Disconnect the battery before you service the
mower. Always disconnect the negative battery
cable before the positive battery cable. Always
connect the positive battery cable before the
negative battery cable.
i Charge the battery in an area with good airflow.
The battery can release hydrogen gas that is
explosive. To prevent an explosion, keep any
device that can cause sparks or flames away from
the battery.
j Disconnect the battery charger from the power
supply before you connect or disconnect the
battery charger to the battery. Wear protective
clothing and use insulated tools when you service
the battery.
k Be careful and wear gloves when you check or
service the cutting unit blades. Replace any
damaged blades, do not try to correct a damaged
blade.
l Keep your hands and feet away from parts that
move. Do not adjust the mower with the engine in
operation, unless the adjustment needs the engine
in operation.
m Carefully release the pressure from components
with stored energy.
n Keep the mower and the engine clean.
o Allow the engine to become cool before storage
and always remove the ignition key.
p Keep all nuts, bolts and screws tight to make sure
the equipment is in safe condition.
q Replace worn or damaged parts for safety.
Replace damaged or worn decals. Only use parts,
accessories and attachments approved by
Jacobsen.
r To decrease the fire hazard, remove materials that
burn from the engine, muffler, battery tray and fuel
tank area.
s Disconnect the battery and controller connectors
before you weld on this mower.
WHEN YOU PUT THE MOWER ON A
TRAILER
a Be careful when you load or unload the mower on
a trailer. Trailer must be wider than the mower and
can carry the weight of the mower.
b Use a full-width ramp to load or unload the mower
on a trailer.
c Use straps, chains, cables or ropes to fasten the
mower to the trailer. Both front and rear straps
must be sent down and toward sides of trailer.
d Make sure that all latches are correctly fastened.
SAFETY 1
7
1.2 IMPORTANT SAFETY NOTES________________________________________________
This safety alert symbol is used to alert you to potential hazards.
DANGER - Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
WARNING - Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious
injury.
CAUTION - Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury
and property damage. It may also be used to alert against unsafe practices.
NOTICE - Indicates a potentially hazardous situation which, if not avoided, MAY result in property damage. It may
also be used to alert against unsafe practices.
For pictorial clarity, some illustrations in this manual may show shields, guards or plates open or removed. Under no
circumstances should this equipment be operated without these devices securely fastened in place.
By following all instructions in this manual, you will prolong the life of your machine and maintain its maximum
efficiency. Adjustments and maintenance should always be performed by a qualified technician.
If additional information or service is needed, contact your Authorized Jacobsen Dealer who is kept informed of the
latest methods to service this equipment and can provide prompt and efficient service.
WARNING
The Interlock System on this machine will shut off the reel and traction drive if
the operator releases the O.P.C. (Operator Presence Control) bail.
To protect the operator and others from injury, never operate equipment with
the Interlock System disconnected or malfunctioning.
!
WARNING
1. Before leaving the operator’s position for any reason:
a. Disengage all drives.
b. Engage parking brake.
c. Disconnect power connector.
2. Keep hands, feet, and clothing away from moving parts. Wait for all
movement to stop before you clean, adjust, or service the machine.
3. Keep the area of operation clear of all bystanders and pets.
4. Chock or block the wheels if the machine is left on an incline.
5. Never operate mowing equipment without the discharge deflector
securely fastened in place.
!
2 CONTROLS
8
2 CONTROLS
2.1 ICONS___________________________________________________________________
2.2 HANDLE CONTROLS ______________________________________________________
A. Parking Brake – Used whenever the mower is left
unattended or as a service brake while transporting.
Always use transport tires when transporting up or
down hills.
B. Speed Paddle – Sets maximum traction drive
speed when O.P.C. Bail is engaged. Push (+) side
of lever to increase speed. Push (-) side of lever to
decrease speed.
C. O.P.C. Bail – Slide bail slightly to the left and
squeeze bail to start traction motor. Traction motor
speed is increased as the bail moves towards the
handle. Release bail to stop unit.
D. Key Switch - The power switch turns the power on
and off. It has three positions OFF, RUN, and
START. Key switch must be in RUN position to start
units equipped with Gen-Set power module.
E. Reel Switch - The reel switch is used to start and
stop the reel.
F. LCD Controls - Used to navigate through menus.
G. LCD Display - Used to display operating conditions.
Figure 2A
WARNING
Never attempt to operate the machine unless you have read the Safety and Operation
Manual, the Parts and Maintenance Manual and know how to operate all controls correctly.
Familiarize yourself with the icons shown above and what they represent. Learn the
location and purpose of all the controls before operating this mower.
Engaged Disengaged
Parking Brake
O.P.C. Traction
Drive
Squeeze bail to handle
Power On
Fast Slow
Throttle
Power Up
Slide Bail Left
Power Off
!
WARNING
To prevent injury, always use transport tires when
transporting unit up or down hills.
!
DANGER
Keep hands and feet away from the cutting unit to
prevent serious injury.
A
B
C
D
E
F
G
!
CONTROLS 2
9
2.3 LCD DISPLAY_____________________________________________________________
The LCD displays current functional values for the
operation of the Eclipse mower and sounds one of three
types of audible alerts. The LCD operates in one of two
modes, Operator Mode (Default), and Maintenance
Mode. Use of Maintenance mode requires a four digit pin
number.
Press either of the orange buttons (K or L) to change
screen display or change values. Push the right orange
button (K) to go forward in the display list or increase
setting value, and push the left orange button (L) to go
back in the display list or decrease setting value. The
black button (J) is used to select, reset, or change
values.
Figure 2B
Audible Alerts indicate one of three conditions detected
by the LCD Display and a corresponding message would
show on the display. A solid tone indicates low system
voltage. A fast beeping (2 per second) alert indicates an
over voltage condition. A slow beeping (1 every 3
seconds) alert indicates mower is in backlap mode.
Alert Displays: In addition to the standard displays for each mode, there are six displays that are used to alert the
operator/mechanic of a problem the needs to be corrected.
G
J
K
L
Alert Display Alert Description
Low Voltage display is shown when system voltage drops below 42 Volts DC on Battery
powered mowers or 38 Volts DC on Gen-Set powered mowers, for 30 seconds and a solid tone
alarm will sound. Press the black button (J) to silence the alarm. Return mower to storage area
or install a fully charged battery pack. Reel motor will not operate with low voltage on the display.
Overvoltage/Check Voltage display is shown when system voltage is above 60 Volts DC and a
fast (2 per second) beeping alarm will sound. If not corrected, controller will shut down after 60
seconds. Check generator output before restarting system. [See Section 5.4].
Traction Motor Controller Fault display is shown when a problem is detected in the traction
motor controller. Traction motor will not operate until the problem is resolved. Return mower to
maintenance area for repair.
Traction Motor Fault display is shown when a traction motor short circuit is detected or the
traction motor current draw exceeds 30 Amps for one second. Traction motor will not operate
until the problem is resolved. Return mower to maintenance area for repair.
Reel Motor Controller Fault display is shown when a problem is detected in the reel motor
controller. Reel motor will not operate until the problem is resolved. Return mower to
maintenance area for repair.
Reel Motor Fault display is shown when a reel motor short circuit is detected or the reel motor
current draw exceeds 30 Amps for one second. Reel motor will not operate until the problem is
resolved. Return mower to maintenance area for repair.
WARNING
Turn reel switch off, release bail, turn key to off position, and disconnect battery connector before checking for
obstructions in reel.
!
2 CONTROLS
10
Operator Mode is used by the operator for system voltage information, travel speed, FOC setting, reel speed, and total
hours on mower. Press the orange buttons (K and L) on the front handle cover to toggle between the different displays.
Operator Mode is view only, only screen illumination mode can be changed.
Display Description
Start-Up Screen - Displays for up to five seconds when system is started.
System Voltage - Displays system voltage between 42 and 59 volts. Screen will be replaced
with alert screen when system voltage drops below 42 volts or rises above 60 volts.
FOC Setting - Displays FOC (Frequency of Clip) setting. When FOC is set to 0, reel will operate
at the fixed reel speed.
Fixed Reel Speed - Displays fixed reel speed setting with FOC set to 0. Fixed reel speed setting
is not used for any FOC other than 0.
Hour Meter - Displays total hours unit has been operated.
Daytime Illumination - When selected, LCD displays dark pixels on a light background. Press
the black button (J) to toggle between daytime and nighttime illumination.
Nighttime Illumination - When selected, LCD displays light pixels on a dark background. Press
the black button (J) to toggle between daytime and nighttime illumination.
Maintenance Mode PIN - Used to enter Maintenance Mode. Maintenance Mode pin is required.
See Maintenance Mode.
CONTROLS 2
11
Maintenance Mode is used to set and adjust all functional values for the Eclipse Mower. LCD displays available in
Maintenance Mode are, maintenance hours, backlap, system voltage, travel speed, set FOC, reel speed, traction
motor current draw, reel motor current draw, total motor current draw, set mow speed, set reel speed, set power
source, set number of reel blades, calibrate speed paddle, calibrate bail lever, set display units, and factory reset.
Figure 2C
See Operator Mode for descriptions of Daytime/
Nighttime Illumination, System Voltage, and Fixed Reel
Speed screens.
2 CONTROLS
12
Display Description
To enter Maintenance Mode, press either orange buttons (K or L) until Maintenance Mode PIN
screen is on the display and press black button (J). Use the orange buttons (K or L) to select and
the black button (J) to enter the digits for the Mechanic Mode pin.
NOTE: The default PIN for Maintenance Mode is 6789. The Maintenance Mode PIN can be
customized to a setting of your choice. Please contact your Jacobsen Dealer or Jacobsen
Technical Support (1800-848-1636 Option 2) for complete instructions.
Maintenance Hours - System can track up to 999.9 hours for maintenance purposes.
To reset maintenance hours, press either of the orange buttons (K or L) on the front cover until
the maintenance hours screen is on the LCD display. Press the black button (J) to move to the
confirm reset screen. Press the right orange button (K) to confirm reset, or press left orange
button (L) to cancel reset.
Backlap Select - Used to switch mower to backlap mode. See Parts & Maintenance Manual
for backlap screen descriptions.
Set FOC - To set the fixed FOC, press either of the orange buttons (K or L) on the front cover
until the FOC set screen is on the LCD display. Press the black button (J) to enter set mode. Use
the orange buttons to raise (K) or lower (L) the FOC value to the desired setting. press the black
button to set speed.
Fixed FOC setting must be 0 or between 0.087 and 0.178 in. (2.2 and 4.5 mm). [See Section
2.4].
Traction Motor Current - Displays current draw of traction drum motor. Fault will be displayed if
current draw is greater than 30 Amps for one second.
Reel Motor Current - Displays current draw of reel motor. Fault will be displayed if current draw
is greater than 30 Amps for one second.
Total Motor Current - Displays total current draw of traction drum motor and reel motor.
Maximum Mow Speed - To set the maximum mow speed, press either of the orange buttons (K
or L) on the front cover until the set max mow speed screen is on the LCD display. Press the
black button (J) to enter set mode. Use the orange buttons to raise (K) or lower (L) the maximum
mow speed to the desired speed. press the black button to set speed.
Maximum mow speed must be between 2.0 and 3.8 MPH (3.2 and 6.1 kph).
Fixed Reel Speed: To set the fixed reel speed, the FOC setting must be set to 0, then press
either of the orange buttons (K or L) on the front cover until the set reel speed screen is on the
LCD display. Press the black button (J) to enter set mode. Use the orange buttons to raise (K) or
lower (L) the reel speed to the desired setting.
Fixed reel speed must be set between 1800 and 2200 rpm.
The Maximum Mow Speed and the Fixed Reel Speed are used to determine the FOC
(Frequency of Cut) [See Section 2.4].
CONTROLS 2
13
Gen-Set Power Module - Used to indicate the gen-set power module is installed on the mower.
This setting is used by system controllers and does not affect operation of mower. Do not
operate mower with incorrect power module setting. Press the black button (J) to toggle
between the power module settings.
Battery Power Module - Used to indicate the battery power module is installed on the mower.
This setting is used by system controllers and does not affect operation of mower. Do not
operate mower with incorrect power module setting. Press the black button (J) to toggle
between the power module settings.
Set Number of Reel Blades: To set the number of reel blades, press either of the orange
buttons (K or L) on the front cover until the reel blades screen is on the LCD display. Press the
black button (J) to enter set mode. Use the orange buttons to set the number of blades.
Available reel blades are 7, 9 (Floating Only), 11 or 15.
Speed Paddle Calibration - Before calibrating the speed paddle, check that paddle stops are
properly adjusted [See Section 6.3].To calibrate the paddle, press either of the orange buttons
(K or L) on the front cover until the speed paddle calibration screen is on the LCD display. Press
the black button (J) to enter set mode. Move the speed paddle through its entire range of
movement to determine minimum and maximum values.
Values displayed will change as controls are moved.
Bail Lever Calibration - To calibrate the bail lever, press either of the orange buttons (K or L) on
the front cover until the bail lever calibration screen is on the LCD display. Press the black button
(J) to enter set mode. Fully engage and disengage the bail lever to determine minimum and
maximum values.
Values displayed will change as controls are moved.
Display Units - To set the display units, press either of the orange buttons (K or L) on the front
cover until the units screen is on the LCD display. Press the black button (J) to toggle between
english (MPH, IN) or metric (KPH, mm) units.
Factory Reset - To reset controller to factory default values, press either of the orange buttons
(K or L) on the front cover until the Factory Reset screen is on the LCD display. Press the black
button (J) to move to the confirm reset screen. Press the right orange button (K) to confirm reset,
or press left orange button (L) to cancel reset.
Maximum Mow Speed......3.4 Mph (5.5 kph)
Reel Speed ......................2200 rpm
Fixed FOC Setting............0.146
Display units.....................English
Display Description
2 CONTROLS
14
2.4 FREQUENCY OF CUT ______________________________________________________
The FOC (Frequency of cut) is the distance, in inches
(mm), the machine travels forward between reel blades
contacting the bedknife. The FOC can be adjusted either
by changing the Fixed FOC setting or by changing the
maximum mow speed and the fixed reel speed on the
LCD display.
Adjust FOC with Fixed FOC setting
Changing the FOC setting to a value other than 0 will
enable the fixed FOC mode and disable the reel speed
setting. As mower travel speed increases or decreases,
reel speed will automatically adjust as required to
maintain set FOC.
Adjust FOC with Reel Speed Setting
1. Using the FOC charts, determine the maximum mow
speed and fixed reel speed required for the desired
FOC.
2. Start the unit in Maintenance mode. [Section 2.3]
3. Set fixed FOC setting to 0
4. Set desired Maximum Mow Speed
5. Set desired Fixed Reel Speed
NOTE: Mow speed is measured in mph (kph), FOC is
measured in inches (millimeters).
CONTROLS 2
15
15 Blade Reel FOC Table
, Product No 63339, 63341, 63335, 63337, 63348, 63350, 63344, 63346 (Standard Reel)
Mow
Speed
Reel RPM
1800 1850 1900 1950 2000 2050 2100 2150 2200
2.00 0.078 0.076 0.074 0.072 0.070 0.069 0.067 0.065 0.064
(3.22) (1.987) (1.933) (1.882) (1.834) (1.788) (1.745) (1.703) (1.663) (1.626)
2.10 0.082 0.080 0.078 0.076 0.074 0.072 0.070 0.069 0.067
(3.38) (2.086) (2.030) (1.976) (1.926) (1.878) (1.832) (1.788) (1.747) (1.707)
2.20 0.086 0.084 0.082 0.079 0.077 0.076 0.074 0.072 0.070
(3.54) (2.186) (2.126) (2.071) (2.017) (1.967) (1.919) (1.873) (1.830) (1.788)
2.30 0.090 0.088 0.085 0.083 0.081 0.079 0.077 0.075 0.074
(3.70) (2.285) (2.223) (2.165) (2.109) (2.056) (2.006) (1.958) (1.913) (1.869)
2.40 0.094 0.091 0.089 0.087 0.084 0.082 0.080 0.079 0.077
(3.86) (2.384) (2.320) (2.259) (2.201) (2.146) (2.093) (2.044) (1.996) (1.951)
2.50 0.098 0.095 0.093 0.090 0.088 0.086 0.084 0.082 0.080
(4.02) (2.484) (2.416) (2.353) (2.293) (2.235) (2.181) (2.129) (2.079) (2.032)
2.60 0.102 0.099 0.096 0.094 0.092 0.089 0.087 0.085 0.083
(4.18) (2.583) (2.513) (2.447) (2.384) (2.325) (2.268) (2.214) (2.162) (2.113)
2.70 0.106 0.103 0.100 0.097 0.095 0.093 0.091 0.088 0.086
(4.35) (2.682) (2.610) (2.541) (2.476) (2.414) (2.355) (2.299) (2.246) (2.195)
2.80 0.110 0.107 0.104 0.101 0.099 0.096 0.094 0.092 0.090
(4.51) (2.782) (2.706) (2.635) (2.568) (2.503) (2.442) (2.384) (2.329) (2.276)
2.90 0.113 0.110 0.107 0.105 0.102 0.100 0.097 0.095 0.093
(4.67) (2.881) (2.803) (2.729) (2.659) (2.593) (2.530) (2.469) (2.412) (2.357)
3.00 0.117 0.114 0.111 0.108 0.106 0.103 0.101 0.098 0.096
(4.83) (2.980) (2.900) (2.823) (2.751) (2.682) (2.617) (2.555) (2.495) (2.438)
3.10 0.121 0.118 0.115 0.112 0.109 0.106 0.104 0.102 0.099
(4.99) (3.080) (2.996) (2.918) (2.843) (2.772) (2.704) (2.640) (2.578) (2.520)
3.20 0.125 0.122 0.119 0.116 0.113 0.110 0.107 0.105 0.102
(5.15) (3.179) (3.093) (3.012) (2.934) (2.861) (2.791) (2.725) (2.661) (2.601)
3.30 0.129 0.126 0.122 0.119 0.116 0.113 0.111 0.108 0.106
(5.31) (3.278) (3.190) (3.106) (3.026) (2.950) (2.879) (2.810) (2.745) (2.682)
3.40 0.133 0.129 0.126 0.123 0.120 0.117 0.114 0.111 0.109
(5.47) (3.378) (3.286) (3.200) (3.118) (3.040) (2.966) (2.895) (2.828) (2.764)
3.50 0.137 0.133 0.130 0.126 0.123 0.120 0.117 0.115 0.112
(5.63) (3.477) (3.383) (3.294) (3.210) (3.129) (3.053) (2.980) (2.911) (2.845)
3.60 0.141 0.137 0.133 0.130 0.127 0.124 0.121 0.118 0.115
(5.79) (3.576) (3.480) (3.388) (3.301) (3.219) (3.140) (3.065) (2.994) (2.926)
3.70 0.145 0.141 0.137 0.134 0.130 0.127 0.124 0.121 0.118
(5.95) (3.676) (3.576) (3.482) (3.393) (3.308) (3.227) (3.151) (3.077) (3.007)
3.80 0.149 0.145 0.141 0.137 0.134 0.130 0.127 0.124 0.122
(6.12) (3.775) (3.673) (3.576) (3.485) (3.398) (3.315) (3.236) (3.160) (3.089)
2 CONTROLS
16
11 Blade Reel FOC Table, Product No. 63334, 63336, 63338, 63340, 63347, 63349, 63343, 63345 (Standard Reel)
Mow
Speed
Reel RPM
1800 1850 1900 1950 2000 2050 2100 2150 2200
2.0
(3.22)
0.107
(2.709)
0.104
(2.636)
0.101
(2.567)
0.098
(2.501)
0.096
(2.438)
0.094
(2.379)
0.091
(2.322)
0.089
(2.268)
0.087
(2.217)
2.1
(3.38)
0.112
(2.845)
0.109
(2.768)
0.106
(2.695)
0.103
(2.626)
0.101
(2.56)
0.098
(2.498)
0.096
(2.438)
0.094
(2.382)
0.092
(2.328)
2.2
(3.54)
0.117
(2.98)
0.114
(2.9)
0.111
(2.823)
0.108
(2.751)
0.106
(2.682)
0.103
(2.617)
0.101
(2.555)
0.098
(2.495)
0.096
(2.438)
2.3
(3.7)
0.123
(3.116)
0.119
(3.032)
0.116
(2.952)
0.113
(2.876)
0.110
(2.804)
0.108
(2.736)
0.105
(2.671)
0.103
(2.609)
0.100
(2.549)
2.4
(3.86)
0.128
(3.251)
0.125
(3.163)
0.121
(3.08)
0.118
(3.001)
0.115
(2.926)
0.112
(2.855)
0.110
(2.787)
0.107
(2.722)
0.105
(2.66)
2.5
(4.02)
0.133
(3.387)
0.130
(3.295)
0.126
(3.208)
0.123
(3.126)
0.120
(3.048)
0.117
(2.974)
0.114
(2.903)
0.112
(2.835)
0.109
(2.771)
2.6
(4.18)
0.139
(3.522)
0.135
(3.427)
0.131
(3.337)
0.128
(3.251)
0.125
(3.17)
0.122
(3.093)
0.119
(3.019)
0.116
(2.949)
0.113
(2.882)
2.7
(4.35)
0.144
(3.658)
0.140
(3.559)
0.136
(3.465)
0.133
(3.376)
0.130
(3.292)
0.126
(3.212)
0.123
(3.135)
0.121
(3.062)
0.118
(2.993)
2.8
(4.51)
0.149
(3.793)
0.145
(3.691)
0.141
(3.593)
0.138
(3.501)
0.134
(3.414)
0.131
(3.33)
0.128
(3.251)
0.125
(3.176)
0.122
(3.103)
2.9
(4.67)
0.155
(3.929)
0.150
(3.822)
0.147
(3.722)
0.143
(3.626)
0.139
(3.536)
0.136
(3.449)
0.133
(3.367)
0.129
(3.289)
0.127
(3.214)
3.0
(4.83)
0.160
(4.064)
0.156
(3.954)
0.152
(3.85)
0.148
(3.751)
0.144
(3.658)
0.140
(3.568)
0.137
(3.483)
0.134
(3.402)
0.131
(3.325)
3.1
(4.99)
0.165
(4.199)
0.161
(4.086)
0.157
(3.978)
0.153
(3.876)
0.149
(3.78)
0.145
(3.687)
0.142
(3.6)
0.138
(3.516)
0.135
(3.436)
3.2
(5.15)
0.171
(4.335)
0.166
(4.218)
0.162
(4.107)
0.158
(4.001)
0.154
(3.901)
0.150
(3.806)
0.146
(3.716)
0.143
(3.629)
0.140
(3.547)
3.3
(5.31)
0.176
(4.47)
0.171
(4.35)
0.167
(4.235)
0.162
(4.127)
0.158
(4.023)
0.155
(3.925)
0.151
(3.832)
0.147
(3.743)
0.144
(3.658)
3.4
(5.47)
0.181
(4.606)
0.176
(4.481)
0.172
(4.363)
0.167
(4.252)
0.163
(4.145)
0.159
(4.044)
0.155
(3.948)
0.152
(3.856)
0.148
(3.768)
3.50 0.187 0.182 0.177 0.172 0.168 0.164 0.160 0.156 0.153
(5.63) (4.741) (4.613) (4.492) (4.377) (4.267) (4.163) (4.064) (3.969) (3.879)
3.60 0.192 0.187 0.182 0.177 0.173 0.169 0.165 0.161 0.157
(5.79) (4.877) (4.745) (4.620) (4.502) (4.389) (4.282) (4.180) (4.083) (3.990)
3.70 0.197 0.192 0.187 0.182 0.178 0.173 0.169 0.165 0.161
(5.95) (5.012) (4.877) (4.748) (4.627) (4.511) (4.401) (4.296) (4.196) (4.101)
3.80 0.203 0.197 0.192 0.187 0.182 0.178 0.174 0.170 0.166
(6.12) (5.148) (5.009) (4.877) (4.752) (4.633) (4.520) (4.412) (4.310) (4.212)
CONTROLS 2
17
9 Blade Reel FOC Table, Product No. 63340, 63349 (Optional Reel)
Mow
Speed
Reel RPM
1800 1850 1900 1950 2000 2050 2100 2150 2200
2.0 0.130 0.127 0.124 0.120 0.117 0.114 0.112 0.109 0.107
(3.22) (3.311) (3.222) (3.137) (3.057) (2.98) (2.908) (2.838) (2.772) (2.709)
2.1 0.137 0.133 0.130 0.126 0.123 0.120 0.117 0.115 0.112
(2.845)
(3.38) (3.477) (3.383) (3.294) (3.21) (3.129) (3.053) (2.98) (2.911)
2.2 0.143 0.140 0.136 0.132 0.129 0.126 0.123 0.120 0.117
(3.54) (3.643) (3.544) (3.451) (3.362) (3.278) (3.198) (3.122) (3.05) (2.98)
2.3 0.150 0.146 0.142 0.138 0.135 0.132 0.129 0.126 0.123
(3.7) (3.808) (3.705) (3.608) (3.515) (3.427) (3.344) (3.264) (3.188) (3.116)
2.4 0.156 0.152 0.148 0.144 0.141 0.137 0.134 0.131 0.128
(3.86) (3.974) (3.866) (3.765) (3.668) (3.576) (3.489) (3.406) (3.327) (3.251)
2.5 0.163 0.159 0.154 0.150 0.147 0.143 0.140 0.136 0.133
(4.02) (4.139) (4.027) (3.921) (3.821) (3.725) (3.634) (3.548) (3.465) (3.387)
2.6 0.169 0.165 0.161 0.156 0.153 0.149 0.145 0.142 0.139
(4.18) (4.305) (4.188) (4.078) (3.974) (3.874) (3.78) (3.69) (3.604) (3.522)
2.7 0.176 0.171 0.167 0.162 0.158 0.155 0.151 0.147 0.144
(4.35) (4.47) (4.35) (4.235) (4.127) (4.023) (3.925) (3.832) (3.743) (3.658)
2.8 0.183 0.178 0.173 0.168 0.164 0.160 0.156 0.153 0.149
(4.51) (4.636) (4.511) (4.392) (4.279) (4.172) (4.071) (3.974) (3.881) (3.793)
2.9 0.189 0.184 0.179 0.174 0.170 0.166 0.162 0.158 0.155
(4.67) (4.802) (4.672) (4.549) (4.432) (4.321) (4.216) (4.116) (4.02) (3.929)
3.0 0.196 0.190 0.185 0.181 0.176 0.172 0.168 0.164 0.160
(4.83) (4.967) (4.833) (4.706) (4.585) (4.47) (4.361) (4.258) (4.159) (4.064)
3.1 0.202 0.197 0.191 0.187 0.182 0.177 0.173 0.169 0.165
(4.99) (5.133) (4.994) (4.863) (4.738) (4.619) (4.507) (4.399) (4.297) (4.199)
3.2 0.209 0.203 0.198 0.193 0.188 0.183 0.179 0.175 0.171
(5.15) (5.298) (5.155) (5.019) (4.891) (4.768) (4.652) (4.541) (4.436) (4.335)
3.3 0.215 0.209 0.204 0.199 0.194 0.189 0.184 0.180 0.176
(5.31) (5.464) (5.316) (5.176) (5.044) (4.917) (4.798) (4.683) (4.574) (4.47)
3.4 0.222 0.216 0.210 0.205 0.199 0.195 0.190 0.186 0.181
(5.47) (5.629) (5.477) (5.333) (5.196) (5.066) (4.943) (4.825) (4.713) (4.606)
3.50 0.228 0.222 0.216 0.211 0.205 0.200 0.196 0.191 0.187
(5.63) (5.795) (5.638) (5.490) (5.349) (5.215) (5.088) (4.967) (4.852) (4.741)
3.60 0.235 0.228 0.222 0.217 0.211 0.206 0.201 0.196 0.192
(5.79) (5.961) (5.799) (5.647) (5.502) (5.364) (5.234) (5.109) (4.990) (4.877)
3.70 0.241 0.235 0.228 0.223 0.217 0.212 0.207 0.202 0.197
(5.95) (6.126) (5.961) (5.804) (5.655) (5.513) (5.379) (5.251) (5.129) (5.012)
3.80 0.248 0.241 0.235 0.229 0.223 0.217 0.212 0.207 0.203
(6.12) (6.292) (6.122) (5.961) (5.808) (5.663) (5.524) (5.393) (5.267) (5.148)
2 CONTROLS
18
7 Blade Reel FOC Table, Product No. 63342, 63351 (Standard Reel) and 63340, 63349 (Optional Reel)
Mow
Speed
Reel RPM
1800 1850 1900 1950 2000 2050 2100 2150 2200
2.0 0.168 0.163 0.159 0.155 0.151 0.147 0.144 0.140 0.137
(3.22) (4.258) (4.142) (4.033) (3.93) (3.832) (3.738) (3.649) (3.564) (3.483)
2.1 0.176 0.171 0.167 0.162 0.158 0.155 0.151 0.147 0.144
(3.38) (4.47) (4.35) (4.235) (4.127) (4.023) (3.925) (3.832) (3.743) (3.658)
2.2 0.184 0.179 0.175 0.170 0.166 0.162 0.158 0.154 0.151
(3.54) (4.683) (4.557) (4.437) (4.323) (4.215) (4.112) (4.014) (3.921) (3.832)
2.3 0.193 0.188 0.183 0.178 0.173 0.169 0.165 0.161 0.158
(3.7) (4.896) (4.764) (4.638) (4.52) (4.407) (4.299) (4.197) (4.099) (4.006)
2.4 0.201 0.196 0.191 0.186 0.181 0.177 0.172 0.168 0.165
(3.86) (5.109) (4.971) (4.84) (4.716) (4.598) (4.486) (4.379) (4.277) (4.18)
2.5 0.210 0.204 0.198 0.193 0.189 0.184 0.180 0.175 0.171
(4.02) (5.322) (5.178) (5.042) (4.913) (4.79) (4.673) (4.562) (4.456) (4.354)
2.6 0.218 0.212 0.206 0.201 0.196 0.191 0.187 0.182 0.178
(4.18) (5.535) (5.385) (5.243) (5.109) (4.981) (4.86) (4.744) (4.634) (4.528)
2.7 0.226 0.220 0.214 0.209 0.204 0.199 0.194 0.189 0.185
(4.35) (5.748) (5.592) (5.445) (5.306) (5.173) (5.047) (4.927) (4.812) (4.703)
2.8 0.235 0.228 0.222 0.217 0.211 0.206 0.201 0.196 0.192
(4.51) (5.961) (5.799) (5.647) (5.502) (5.364) (5.234) (5.109) (4.99) (4.877)
2.9 0.243 0.236 0.230 0.224 0.219 0.213 0.208 0.203 0.199
(4.67) (6.173) (6.007) (5.848) (5.699) (5.556) (5.421) (5.291) (5.168) (5.051)
3.0 0.251 0.245 0.238 0.232 0.226 0.221 0.216 0.210 0.206
(4.83) (6.386) (6.214) (6.05) (5.895) (5.748) (5.607) (5.474) (5.347) (5.225)
3.1 0.260 0.253 0.246 0.240 0.234 0.228 0.223 0.218 0.213
(4.99) (6.599) (6.421) (6.252) (6.092) (5.939) (5.794) (5.656) (5.525) (5.399)
3.2 0.268 0.261 0.254 0.248 0.241 0.235 0.230 0.225 0.219
(5.15) (6.812) (6.628) (6.454) (6.288) (6.131) (5.981) (5.839) (5.703) (5.573)
3.3 0.277 0.269 0.262 0.255 0.249 0.243 0.237 0.232 0.226
(5.31) (7.025) (6.835) (6.655) (6.485) (6.322) (6.168) (6.021) (5.881) (5.748)
3.4 0.285 0.277 0.270 0.263 0.256 0.250 0.244 0.239 0.233
(5.47) (7.238) (7.042) (6.857) (6.681) (6.514) (6.355) (6.204) (6.06) (5.922)
3.50 0.293 0.285 0.278 0.271 0.264 0.258 0.251 0.246 0.240
(5.63) (7.451) (7.249) (7.059) (6.878) (6.706) (6.542) (6.386) (6.238) (6.096)
3.60 0.302 0.294 0.286 0.279 0.272 0.265 0.259 0.253 0.247
(5.79) (7.664) (7.456) (7.260) (7.074) (6.897) (6.729) (6.569) (6.416) (6.270)
3.70 0.310 0.302 0.294 0.286 0.279 0.272 0.266 0.260 0.254
(5.95) (7.876) (7.664) (7.462) (7.271) (7.089) (6.916) (6.751) (6.594) (6.444)
3.80 0.318 0.310 0.302 0.294 0.287 0.280 0.273 0.267 0.261
(6.12) (8.089) (7.871) (7.664) (7.467) (7.280) (7.103) (6.934) (6.772) (6.619)
CONTROLS 2
19
2.5 GAS POWER MODULE CONTROLS___________________________________________
M. Engine Switch – The engine switch enables and
disables the engine ignition system. The engine
switch must be in the ON position for the engine to
run. Turning the engine switch to the OFF position
stops the engine.
N. Choke Lever - The choke lever opens and closes
the choke valve in the carburetor. The CLOSED
position enriches the fuel mixture for starting a cold
engine. The OPEN position provides the correct fuel
mixture for operation after starting, and for restarting
a warm engine.
P. Fuel Valve Lever - The fuel valve opens and closes
the connection between the fuel tank and the
carburetor. The fuel valve lever must be in the ON
position for the engine to run. When the engine is
not in use, leave the fuel valve lever in the OFF
position to prevent carburetor flooding, and to
reduce the possibility of fuel leakage.
Figure 2D
Figure 2E
2.6 BATTERY POWER MODULE CONTROLS ______________________________________
R. Battery Monitor - Located on the removable battery
pack displays battery charge level.
Figure 2F
NOTICE
Before tipping mower back for adjustments, the fuel
lever must be moved to the OFF position to prevent
fuel from leaking into the crankcase.
OFF
ON
M
N
P
R
3 SET UP
20
3 SET UP
3.1 GENERAL________________________________________________________________
The set-up and testing of the unit should always be
performed by a trained technician, familiar with the
operation of the equipment.
Read each instruction completely and make sure you
understand it before proceeding with the assembly. Stay
alert for potential hazards and obey all safety
precautions.
The RIGHT, LEFT, FRONT and REAR of the machine are
referenced from the operator’s seat, facing forward.
Accessories not included with this product must be
ordered separately. See instructions provided with
accessory for installation and parts.
This machine is shipped assembled. After unpacking,
perform the initial inspection, operating checks, and test
the Operator Presence Control (OPC).
3.2 INITIAL INSPECTION_______________________________________________________
1. Perform a visual inspection of the entire unit, look for
signs of wear, loose hardware, and components that
may have been damaged during transport.
2. Inspect paint and decals for damage or scratches.
Decals provide important operating and safety
information. Replace all missing or hard to read
decals.
3. Check that the engine oil level is at the full level
mark with the engine cold.
4. Visually check for fuel or oil leaks.
5. Inspect lube points for proper lubrication.
3.3 OPERATING CHECKS______________________________________________________
After the initial inspection, test the machine for proper
operation.
1. Test the Operator Presence Control. (Section 4.4)
2. Start the machine and check that controls operate
as described. (Section 3.2)
3. After operation, stop and inspect again for fuel or oil
leaks.
CAUTION
Do not attempt to operate the machine unless
you are familiar with this type of equipment and
know how to operate all controls correctly.
!
CAUTION
The initial inspection should be performed only when the engine is off and all fluids are cold.
Disengage all drives, engage parking brake, and stop engine.
!
1 / 1

Jacobsen eclipse 2 InCommand Dealer's Manual

Kategooria
Muruniidukid
Tüüp
Dealer's Manual

teistes keeltes