Makita UR012G Kasutusjuhend

Bränd: Makita

Mudel: UR012G

Kategooria: Elektrilised tööriistad

Tüüp: Kasutusjuhend

UR012G

EN Cordless Grass Trimmer INSTRUCTION MANUAL 11

SV Batteridriven grästrimmer BRUKSANVISNING 25

NO Batteridrevet gresstrimmer BRUKSANVISNING 39

FI Akkukäyttöinen

viimeistelyleikkuri KÄYTTÖOHJE 53

DA Akku græstrimmer BRUGSANVISNING 67

LV Bezvada zāles

apgriezējmašīna LIETOŠANAS INSTRUKCIJA 81

LT Belaidė žoliapjovė NAUDOJIMO INSTRUKCIJA 95

ET Akuga murutrimmer KASUTUSJUHEND 109

RU Аккумуляторная Коса РУКОВОДСТВО ПО

ЭКСПЛУАТАЦИИ 123

Fig.1

12 2

Fig.2

12 1

Fig.3

12 13 14

1 2

4 5

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

Fig.16

2 2

Fig.17

Fig.18

Fig.19

Fig.20

Fig.21

Fig.22

Fig.23

Fig.24

Fig.25

Fig.26

Fig.27

Fig.28

Fig.29

Fig.30

Fig.31

Fig.32

750 mm

100-300 mm

Fig.33

Fig.34

Fig.35

Fig.36

Fig.37

Fig.38

Fig.39

3 m

80 mm

100 mm

Fig.40

3 m

100 mm

Fig.41

Fig.42

Fig.43

90°

Fig.44

11 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: UR012G

Handle type Bike handle

No load speed

(at each rotation speed level)

Cutter blade / Plastic blade 3: 0 - 6,800 min-1

2: 0 - 5,000 min-1

1: 0 - 3,500 min-1

Nylon cutting head 3: 0 - 5,000 min-1

2: 0 - 4,200 min-1

1: 0 - 3,500 min-1

Overall length

(without cutting tool)

1,790 mm

Nylon cord diameter 2.4 - 3.0 mm

Applicable cutting tool and

cutting diameter

2-tooth blade

(P/N 195624-6)

305 mm

3-tooth blade

(P/N 195300-2)

305 mm

4-tooth blade

(P/N 196895-8)

255 mm

8-tooth blade

(P/N B-14146)

255 mm

Chisel blade

(P/N 199872-9)

225 mm

Shredder blade

(P/N 199874-5)

270 mm

Nylon cutting head

(P/N 199884-2)

480 mm

Plastic blade

(P/N 199868-0)

305 mm

Rated voltage D.C. 72 V - 80 V max

Net weight 8.0 - 9.3 kg

Protection degree IPX4

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsmaydierfromcountrytocountry.

• Theweightmaydierdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL4020 / BL4025 / BL4040 / BL4050F*

* : Recommended battery

Charger DC40RA / DC40RB / DC40RC

• Some of the battery cartridges and chargers listed above may not be available depending on your region of

residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

andchargersmaycauseinjuryand/orre.

Symbols

The followings show the symbols which may be used

for the equipment. Be sure that you understand their

meaning before use.

Take particular care and attention.

Read instruction manual.

15m(50FT)Keep distance at least 15 m.

Caution; kickback

12 ENGLISH

Wear a helmet, goggles and ear protection.

Wear protective gloves.

Wear sturdy boots with nonslip soles.

Steeltoed safety boots are recommended.

Danger;beawareofthrownobjects.

Warning; Disconnect battery before

maintenance.

Warning: Hot surface. Risk of burns. Do not

touch metal part until cooled.

Wear eye and ear protection.

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical

and electronic equipment, accumulators

and batteries may have a negative impact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household

waste!

In accordance with the European Directive

on waste electrical and electronic equip-

ment and on accumulators and batteries

and waste accumulators and batteries,

as well as their adaptation to national law,

waste electrical equipment, batteries and

accumulators should be stored separately

and delivered to a separate collection point

for municipal waste, operating in accor-

dance with the regulations on environmen-

tal protection.

This is indicated by the symbol of the

crossed-out wheeled bin placed on the

equipment.

Guaranteed sound power level according

to EU Outdoor Noise Directive.

Sound power level according to Australia

NSW Noise Control Regulation.

Noise

Cutting tool

Sound pressure level (LpA)

dB(A)

Sound power level (LWA)

dB(A)

Applicable

standard

LpA dB(A) Uncer-

tainty (K)

dB(A)

LWA dB(A) Uncer-

tainty (K)

dB(A)

2-tooth blade 82.3 1.7 96.2 0.8

ISO22868

(ISO11806-1)

3-tooth blade 86.1 0.4 99.4 0.6

ISO22868

(ISO11806-1)

4-tooth blade 84.3 2.1 97.7 2.1

ISO22868

(ISO11806-1)

Nylon cutting head 79.9 1.8 91.6 1.5

ISO22868

(ISO11806-1)/

EN50636-2-91

Plastic blade 82.7 0.6 92.4 1.1

ISO22868

(ISO11806-1)/

EN50636-2-91

• Even if the sound pressure level listed above is 80 dB (A) or less, the level under working may exceed 80 dB

(A). Wear ear protection.

NOTE: The declared noise emission value(s) has been measured in accordance with a standard test method and

may be used for comparing one tool with another.

NOTE: The declared noise emission value(s) may also be used in a preliminary assessment of exposure.

WARNING: Wear ear protection.

WARNING: The noise emission during actual use of the power tool can dier from the declared val-

ue(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.

WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation

of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the

times when the tool is switched o and when it is running idle in addition to the trigger time).

13 ENGLISH

Vibration

Applicable standard : ISO22867(ISO11806-1)

Cutting tool Left hand Right hand

ah,W (m/s2)Uncertainty K

(m/s2)

ah,W (m/s2)Uncertainty K

(m/s2)

2-tooth blade 2.5 1.5 2.5 1.5

3-tooth blade 2.5 1.5 2.5 1.5

4-tooth blade 2.5 1.5 2.5 1.5

Nylon cutting head 2.5 1.5 2.5 1.5

Plastic blade 2.5 1.5 2.5 1.5

NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and

may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also be used in a preliminary assessment of exposure.

WARNING: The vibration emission during actual use of the power tool can dier from the declared

value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.

WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation

of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the

times when the tool is switched o and when it is running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listedbelowmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Important safety instructions for the

tool

WARNING: Read all safety warnings and

all instructions. Failure to follow the warnings and

instructionsmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

Intended use

1. This tool is only intended for cutting grass,

weeds, bushes and undergrowth. It should not

be used for any other purpose such as edging

or hedge cutting as this may cause injury.

General instructions

1. Never allow people unfamiliar with these

instructions, people (including children) with

reduced physical, sensory or mental capabil-

ities, or lack of experience and knowledge to

use the tool. Children should be supervised to

ensure that they do not play with the tool.

2. Before starting the tool, read this instruction

manual to become familiar with the handling of

the tool.

3. Do not lend the tool to a person with insu-

cient experience or knowledge regarding han-

dling of brushcutters and string trimmers.

4. When lending the tool, always attach this

instruction manual.

Handle the tool with the utmost care and attention.

6. Never use the tool after consuming alcohol or

drugs, or if feeling tired or ill.

7. Never attempt to modify the tool.

Follow the regulations about handling of brush-

cutters and string trimmers in your country.

Personal protective equipment

►Fig.1

1. Wear safety helmet, protective goggles and

protective gloves to protect yourself from

ying debris or falling objects.

14 ENGLISH

2. Wear ear protection such as ear mus to pre-

vent hearing loss.

3. Wear proper clothing and shoes for safe

operation, such as a work overall and sturdy,

non-slip shoes. Do not wear loose clothing or

jewelry.Looseclothes,jewelryorlonghaircanbe

caught in moving parts.

When touching the cutting blade, wear protective

gloves. Cutting blades can cut bare hands severely.

Work area safety

1. Operate the tool under good visibility and day-

light conditions only. Do not operate the tool in

darkness or fog.

2. Do not operate the tool in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. The tool creates sparks

which may ignite the dust or fumes.

3. During operation, never stand on an unstable

or slippery surface or a steep slope. During

the cold season, beware of ice and snow and

always ensure secure footing.

4. During operation, keep bystanders or animals

at least 15 m away from the tool. Stop the tool

as soon as someone approaches.

5. Never operate the tool while people, especially

children, or pets are nearby.

6. Before operation, examine the work area for

stones or other solid objects. They can be

thrown or cause dangerous kickback and result in

seriousinjuryand/orpropertydamage.

7. WARNING: Use of this product can create

dust containing chemicals which may cause

respiratory or other illnesses. Some examples

of these chemicals are compounds found in

pesticides, insecticides, fertilizers and herbi-

cides. Your risk from these exposures varies,

depending on how often you do this type

of work. To reduce your exposure to these

chemicals: work in a well ventilated area, and

work with approved safety equipment, such as

those dust masks that are specially designed

to lter out microscopic particles.

Electrical and battery safety

1. Do not expose the tool to rain or wet condi-

tions. Water entering the tool will increase the risk

of electric shock.

Do not use the tool if the switch does not turn it

on and o. Any tool that cannot be controlled with

the switch is dangerous and must be repaired.

Prevent unintentional starting. Ensure the switch

is in the o-position before installing a battery

pack, picking up or carrying the tool. Carrying the

toolwithyourngerontheswitchorenergisingthe

tool that have the switch on invites accidents.

4. Do not dispose of the battery(ies) in a re.

The cell may explode. Check with local codes for

possible special disposal instructions.

Do not open or mutilate the battery(ies). Released

electrolyte is corrosive and may cause damage to

the eyes or skin. It may be toxic if swallowed.

6. Do not charge battery in rain, or in wet

locations.

Avoid dangerous environment. Don't use the tool

in dump or wet locations or expose it to rain. Water

entering the tool will increase the risk of electric shock.

8. Do not charge the battery outdoors.

9. Do not handle charger, including charger plug,

and charger terminals with wet hands.

10. Do not replace the battery with wet hands.

11. Do not replace the battery in the rain.

12. Do not wet the terminal of battery with liquid

such as water, or submerge the battery. Do not

leave the battery in the rain, nor charge, use,

or store the battery in a damp or wet place. If

the terminal gets wet or liquid enters inside of bat-

tery, the battery may be short circuited and there is

ariskofoverheat,re,orexplosion.

13. After removing the battery from the tool or

charger, be sure to attach the battery cover to

the battery and store it in a dry place.

14.

If the battery cartridge gets wet, drain the water

inside and then wipe it with a dry cloth. Dry the bat-

tery cartridge completely in a dry place before use.

Putting into operation

1. Before assembling or adjusting the tool,

remove the battery cartridge.

2. Before handling the cutter blade, wear protec-

tive gloves.

Before installing the battery cartridge, inspect

the tool for damages, loose screws/nuts or

improper assembly. Sharpen blunt cutter blade.

If the cutter blade is bent or damaged, replace

it. Check all control levers and switches for

easy action. Clean and dry the handles.

4. Never attempt to switch on the tool if it is dam-

aged or not fully assembled. Otherwise serious

injurymayresult.

5. Adjust the shoulder harness and hand grip to

suit the operator's body size.

When inserting a battery cartridge, keep the cutting

attachment clear of your body and other object,

including the ground. It may rotate when starting and

maycauseinjuryordamagetothetooland/orproperty.

7. Remove any adjusting key, wrench or blade

cover before turning the tool on. An accessory

left attached to a rotating part of the tool may

resultinpersonalinjury.

8. The cutting tool has to be equipped with the

guard. Never run the tool with damaged guards

or without guards in place!

9. Make sure there are no electrical cables, water

pipes, gas pipes etc. that could cause a hazard

if damaged by use of the tool.

Operation

1. In the event of an emergency, switch o the

tool immediately.

If you feel any unusual condition (e.g. noise,

vibration) during operation, switch o the tool

and remove the battery cartridge. Do not use the

tool until the cause is recognized and solved.

3. The cutting attachment continues to rotate for

a short period after turning the tool o. Don't

rush to contact the cutting attachment.

15 ENGLISH

4. During operation, use the shoulder harness.

Keep the tool on your right side rmly.

5. Do not overreach. Keep proper footing and

balance at all times. Watch for hidden obsta-

cles such as tree stumps, roots and ditches to

avoid stumbling.

6. Always be sure of your footing on slopes.

7. Walk, never run.

8. Never work on a ladder or tree to avoid loss of

control.

9. If the tool gets heavy impact or fall, check the

condition before continuing work. Check the

controls and safety devices for malfunction. If

there is any damage or doubt, ask our autho-

rized service center for the inspection and

repair.

10. Do not touch the gear case during and imme-

diately after the operation. The gear case

becomes hot during operation and can cause burn

injury.

11. Take a rest to prevent loss of control caused

by fatigue. We recommend taking a 10 to 20-min-

ute rest every hour.

12. When you leave the tool, even if it is a short

time, always remove the battery cartridge. The

unattended tool with the battery cartridge installed

may be used by unauthorized person and cause

serious accident.

13. If grass or branches get caught between the

cutting attachment and guard, always turn

the tool o and remove the battery cartridge

before cleaning. Otherwise the cutting attach-

ment may rotate unintentionally and cause serious

injury.

14. Never touch moving hazardous parts before

the moving hazardous parts have come to

a complete stop and the battery cartridge is

removed.

15. If the cutting attachment hits stones or other

hard objects, immediately turn the tool o.

Then remove the battery cartridge and inspect

the cutting attachment.

16. Check the cutting attachment frequently

during operation for cracks or damages.

Before the inspection, remove the battery

cartridge and wait until the cutting attachment

stops completely. Replace damaged cutting

attachment immediately, even if it has only

supercial cracks.

17. Never cut above waist height.

18. Before starting the cutting operation, wait until

the cutting attachment reaches a constant

speed after turning the tool on.

19. When using a cutting blade, swing the tool

evenly in half-circle from right to left, like

using a scythe.

20. Hold the tool by insulated gripping surfaces

only, because the cutter blade may contact

hidden wiring. Cutter blades contacting a "live"

wire may make exposed metal parts of the tool

"live" and could give the operator an electric

shock.

21. Do not start the tool when the cutting tool is

tangled with cut grass.

22. Before starting the tool, be sure that the cut-

ting tool is not touching the ground and other

obstacles such as a tree.

23. During operation always hold the tool with

both hands. Never hold the tool with one hand

during use.

24. Do not use the tool when there is a risk of

lightning.

25. When you use the tool on muddy ground, wet

slope, or slippery place, pay attention to your

footing.

26. Avoid working in poor environment where

increased user fatigue is expected.

27. Do not use the tool in bad weather where visi-

bility is limited. Failure to do so may cause fall or

incorrect operation due to low visibility.

28. Do not submerge the tool into a puddle.

29. Do not leave the tool unattended outdoors in

the rain.

30. When wet leaves or dirt adhere to the suc-

tion mouth (ventilation window) due to rain,

remove them.

31. Do not use the tool in the snow.

Cutting tools

1. Do not use a cutting tool which is not recom-

mended by Makita.

2. Use an applicable cutting attachment for the

job in hand.

— Nylon cutting heads (string trimmer heads)

and plastic blades are suitable for trimming

lawn grass.

— Cutting blades are suitable for cutting weeds,

high grasses, bushes, shrubs, underwood,

thicket, and the like.

— Never use other blades including metal

multi-piecepivotingchainsandailblades.It

mayresultinseriousinjury.

3. Only use the cutting tool that are marked with

a speed equal or higher than the speed marked

on the tool.

4. Always keep your hands, face, and clothes

away from the cutting tool when it is rotating.

Failuretodosomaycausepersonalinjury.

5. Always use the cutting attachment guard prop-

erly suited for the cutting attachment used.

6. When using cutting blades, avoid kickback

and always prepare for an accidental kickback.

See the section for Kickback.

7. When not in use, attach the blade cover onto

the blade. Remove the cover before operation.

Kickback (Blade thrust)

1. Kickback (blade thrust) is a sudden reaction

to a caught or bound cutting blade. Once it

occurs, the tool is thrown sideway or toward

the operator at great force and it may cause

serious injury.

2. Kickback occurs particularly when applying

the blade segment between 12 and 2 o'clock

to solids, bushes and trees with 3 cm or larger

diameter.

►Fig.2

16 ENGLISH

3. To avoid kickback:

Apply the segment between 8 and 11 o'clock.

2. Never apply the segment between 12 and

2 o'clock.

Never apply the segment between 11 and

12 o'clock and between 2 and 5 o'clock,

unless the operator is well trained and

experienced and does it at his/her own risk.

4. Never use cutting blades close to solids,

such as fences, walls, tree trunks and

stones.

5. Never use cutting blades vertically, for

such operations as edging and trimming

hedges.

►Fig.3

Vibration

1. People with poor circulation who are exposed

to excessive vibration may experience injury

to blood vessels or the nervous system.

Vibration may cause the following symptoms

tooccurinthengers,handsorwrists:"Falling

asleep" (numbness), tingling, pain, stabbing sen-

sation, alteration of skin color or of the skin. If any

of these symptoms occur, see a physician!

2. To reduce the risk of "white nger disease",

keep your hands warm during operation and

well maintain the tool and accessories.

Transport

1. Before transporting the tool, turn it o and

remove the battery cartridge. Attach the cover

to the cutting blade.

2. When transporting the tool, carry it in a hori-

zontal position by holding the shaft.

3. When transporting the tool in a vehicle, prop-

erly secure it to avoid turnover. Otherwise

damage to the tool and other baggage may result.

Maintenance

1. Have your tool serviced by our authorized

service center, always using only genuine

replacement parts. Incorrect repair and poor

maintenance can shorten the life of the tool and

increase the risk of accidents.

2. Before doing any maintenance or repair work

or cleaning the tool, always turn it o and

remove the battery cartridge.

3. Always wear protective gloves when handling

the cutting blade.

4. Always clean dust and dirt o the tool. Never

use gasoline, benzine, thinner, alcohol or the

like for the purpose. Discoloration, deformation

or cracks of the plastic components may result.

5. After each use, tighten all screws and nuts.

6. Do not attempt any maintenance or repair not

described in the instruction manual. Ask our

authorized service center for such work.

7. Always use our genuine spare parts and

accessories only. Using parts or accessories

supplied by a third party may result in the tool

breakdown, property damage and/or serious

injury.

Request our authorized service center to

inspect and maintain the tool at regular interval.

9. Always keep the tool in good working condi-

tion. Poor maintenance can result in inferior per-

formance and shorten the life of the tool.

10. Do not wash the tool with high pressure water.

11. When washing the tool, do not let water enter

the electrical mechanism such as battery,

motor, and terminals.

12. When storing the tool, avoid direct sunlight

and rain, and store it in a place where it does

not get hot or humid.

13. Perform inspection or maintenance in a place

where rain can be avoided.

14. After using the tool, remove the adhered dirt

and dry the tool completely before storing.

Depending on the season or the area, there is a

risk of malfunction due to freezing.

Storage

1. Before storing the tool, perform full cleaning

and maintenance. Remove the battery car-

tridge. Attach the cover to the cutting blade.

2. Store the tool in a dry and high or locked loca-

tion out of reach of children.

3. Do not prop the tool against something, such

as a wall. Otherwise it may fall suddenly and

causeaninjury.

First aid

Always have a rst-aid kit close by. Immediately

replace any item taken from the rst aid kit.

2. When asking for help, give the following

information:

— Place of the accident

— What happened

— Numberofinjuredpersons

— Natureoftheinjury

— Your name

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper the battery

cartridge.Itmayresultinare,excessiveheat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

17 ENGLISH

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re,excessiveheat,orexplosion.

9. Do not use a damaged battery.

10.

The contained lithium-ion batteries are subject to

the Dangerous Goods Legislation requirements.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tapeormaskoopencontactsandpackupthe

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may result in poor performance or

breakdown of the tool or battery cartridge.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near a high-voltage elec-

trical power lines. It may result in a malfunction

or breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causingres,personalinjuryanddamage.Itwill

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

PARTS DESCRIPTION

►Fig.4

1Speed indicator 2ADT indicator

(ADT = Automatic Torque

Drive Technology)

3Caution lamp 4Main power button

5Reverse button 6Battery cartridge 7Hanger 8Lock-olever

9Switch trigger 10 Knob 11 Handle 12 Protector (for cutter

blade / nylon cutting

head / plastic blade)

13 Protector (for chisel

blade)

14 Protector (for shredder

blade)

15 Protector extension (for

nylon cutting head /

plastic blade)

16 Shoulder harness

NOTE: The protector supplied as the standard accessory varies depending on the countries.

18 ENGLISH

FUNCTIONAL DESCRIPTION

WARNING:

Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

Failuretoswitchoandremovethebatterycartridgemay

resultinseriouspersonalinjuryfromaccidentalstart-up.

Installing or removing battery cartridge

CAUTION: Always switch o the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridgermlymaycausethemtoslipoyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►Fig.5: 1. Red indicator 2. Button 3. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator as

showninthegure,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem.Thissystemautomaticallycutsopowertothe

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Caution lamp Status

Color On Blinking

Green Overload

Red (tool) / (battery) Overheat

Red

Overdischarge

Overload protection

If the tool gets into one of the following situation, the tool auto-

matically stops and the caution lamp starts blinking in green:

—

The tool is overloaded by entangled weeds or other debris.

— The cutter blade is locked or kicked back.

— The main power button is turned on while the

switch trigger is being pulled.

In this situation, release the trigger and pull it again to

resume.

CAUTION: If you need to remove the entan-

gled weeds on the tool or release the locked

cutter blade, be sure to turn the tool o before

you start.

Overheat protection for tool or battery

If the tool or battery cartridge is overheated, the tool

stops automatically. When the tool is overheated, the

caution lamp lights up in red. When the battery cartridge

is overheated, the caution lamp blinks in red. Let the tool

and/or battery cool down before turning the tool on again.

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically and the caution lamp starts blinking in red.

If the tool does not operate even when the switches are

operated, remove the battery cartridge from the tool and

charge it.

Indicating the remaining battery

capacity

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

►Fig.6: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydierslightly

from the actual capacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

the battery protection system works.

Main power switch

Tap the main power button to turn on the tool.

Toturnothetool,pressandholdthemainpower

buttonuntilthespeedindicatorgoeso.

►Fig.7: 1. Speed indicator 2. Main power button

NOTE:Thetoolwillautomaticallyturnedoifitisleft

without any operations for a certain period of time.

19 ENGLISH

Switch action

WARNING: For your safety, this tool is

equipped with lock-o lever which prevents the

tool from unintended starting. NEVER use the tool

if it runs when you simply pull the switch trigger

without pressing the lock-o lever. Return the

tool to our authorized service center for proper

repairs BEFORE further usage.

WARNING: NEVER tape down or defeat pur-

pose and function of lock-o lever.

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released. Operating a tool

with a switch that does not actuate properly can lead

tolossofcontrolandseriouspersonalinjury.

CAUTION: Never put your nger on the main

power button and switch trigger when carrying

the tool. The tool may start unintentionally and cause

injury.

NOTICE: Do not pull the switch trigger hard with-

out pressing the lock-o lever. This can cause

switch breakage.

To prevent the switch trigger from being accidentally

pulled,alock-oleverisprovided.Tostartthetool,

depressthelock-oleverandpulltheswitchtrigger.

The tool speed increases by increasing pressure on the

switch trigger. Release the switch trigger to stop.

►Fig.8: 1.Lock-olever2. Switch trigger

Speed adjusting

Youcanadjustthetoolspeedbytappingthemain

power button. Each time you tap the main power button,

the level of speed will change. The tool automatically

adjuststherotationspeedaccordingtothecuttingtool

attached to the tool.

►Fig.9: 1. Speed indicator 2. Main power button

Speed

indicator

Mode Rotation speed

Cutter blade/

Plastic blade

Nylon cutting

head

High

0 - 6,800 min-1 0 - 5,000 min-1

Medium

0 - 5,000 min-1 0 - 4,200 min-1

Low

0 - 3,500 min-1 0 - 3,500 min-1

Automatic Torque Drive Technology

When you turn on the Automatic Torque Drive

Technology (ADT), the tool runs at optimum rotation

speed and torque for the condition of grass being cut.

The tool automatically detects the cutting tool attached

and choose a suitable rotation speed.

To start ADT, press and hold the reverse button until the

ADT indicator turns on.

To stop ADT, press and hold the reverse button until the

ADTindicatorturnso.

►Fig.10: 1. ADT indicator 2. Reverse button

Indicator Mode Cutting tool Rotation

speed

ADT Cutter blade

Plastic blade

3,500 - 6,800

min-1

Nylon cutting

head

3,500 - 5,000

min-1

Reverse button for debris removal

WARNING: Switch o the tool and remove

the battery cartridge before you remove entan-

gled weeds or debris which the reverse rotation

function can not remove.Failuretoswitchoand

remove the battery cartridge may result in serious

personalinjuryfromaccidentalstart-up.

This tool has a reverse button to change the direction of

rotation. It is only for removing weeds and debris entan-

gled in the tool.

To reverse the rotation, tap the reverse button and pull

theswitchtriggerwhiledepressingthelock-olever

when the cutting tool is stopped. The speed indicators

and ADT indicator start blinking, and the cutting tool

rotates in reverse direction when you pull the switch

trigger.

To return to regular rotation, release the trigger and wait

until the cutting tool stops.

►Fig.11: 1. Speed indicator 2. ADT indicator

3. Reverse button

NOTE: During the reverse rotation, the tool operates

only for a short period of time and then automatically

stops.

NOTE: Once the tool is stopped, the rotation returns

to regular direction when you start the tool again.

NOTE: If you tap the reverse button while the cutting

tool is still rotating, the tool comes to stop and to be

ready for reverse rotation.

Electric brake

This tool is equipped with an electric brake. If the tool

consistently fails to quickly stop after the switch trigger

is released, have the tool serviced at a Makita service

center.

20 ENGLISH

Electronic function

Constant speed control

The speed control function provides the constant rota-

tion speed regardless of load conditions.

Soft start feature

Soft start because of suppressed starting shock.

ASSEMBLY

WARNING: Always be sure that the tool is

switched o and battery cartridge is removed

before carrying out any work on the tool. Failure to

switchoandremovethebatterycartridgemayresult

inseriouspersonalinjuryfromaccidentalstart-up.

WARNING: Never start the tool unless it is

completely assembled. Operation of the tool in a

partially assembled state may result in serious per-

sonalinjuryfromaccidentalstart-up.

Installing the handle

1. Insert the shaft of the handle into the grip. Align

the screw hole in the grip with the one in the shaft.

Tighten the screw securely.

►Fig.12: 1. Grip 2. Screw 3. Shaft

NOTICE: Note the direction of the grip. The

screw holes will not be aligned if the grip is not

inserted in the correct direction.

2. Place the spring onto the base.

►Fig.13: 1. Knob 2. Handle clamp 3. Handle

4. Handle holder 5. Spring 6. Base

3. Place the handle between the handle clamp and

handle holder.

4. Temporarily attach the handle by tightening the

knob,andadjustthehandleposition.

5. Fully tighten the knob.

Hex wrench storage

CAUTION: Be careful not to leave the hex

wrench inserted in the gear case. It may cause

injuryanddamagetothetool.

When not in use, store the hex wrench as illustrated to

keep it from being lost.

►Fig.14: 1. Hex wrench

►Fig.15: 1. Hex wrench 2. Handle clamp

Correct combination of the cutting

tool and the protector

CAUTION: Always use the correct combi-

nation of cutting tool and the protector. A wrong

combination may not protect you from the cutting tool,

yingdebris,andstones.Itcanalsoaectthebal-

anceofthetoolandresultinaninjury.

Cutting tool Protector

Cutter blade

(2-tooth, 3-tooth, 4-tooth, and

8-tooth blades)

Nylon cutting head

Plastic blade

Chisel blade

Shredder blade

Installing the protector

WARNING: Never use the tool without the

guard or with the guard improperly installed.

Failuretodosocancauseseriouspersonalinjury.

NOTE: The type of the protector supplied as the stan-

dard accessory varies depending on the countries.

For cutter blade

Attach the protector to the clamp using bolts.

►Fig.16: 1. Clamp 2. Protector

Leht laadib ...

Makita UR012G Kasutusjuhend

Bränd: Makita

Mudel: UR012G

Kategooria: Elektrilised tööriistad

Tüüp: Kasutusjuhend

Laadige alla PDF

aruanne

teistes keeltes

svenska: Makita UR012G Användarmanual
dansk: Makita UR012G Brugermanual

Makita UR012G Kasutusjuhend

Makita UR012G Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid