Makita LS1214F Kasutusjuhend

Kaubamärk: Makita

Mudel: LS1214F

Kategooria: Leegisaed

Tüüp: Kasutusjuhend

See juhend sobib ka

GB Slide Compound Saw Instruction manual

ID Gergaji Kombinasi Geser

Petunjuk penggunaan

VI Maùy cöa ña goùc Taøi lieäu höôùng daãn

TH   

LS1214

LS1214F

LS1214L

005689

1 001564 2 001531

3 002016 4 001782

5 001537 6 001538

7 004066 8 001540

9 001562 10 001541

11 004056 12 001543

13 005592 14 001551

20 24

15 002026 16 003826

17 006339 18 006340

19 006341 20 001530

21 002019 22 002020

23 002021 24 004058

25 001536 26 006793

27 006792 28 006794

29 001549 30 005593

36 35 36 6

31 005594 32 005595

33 005597 34 005688

35 001550 36 005232

37 001544 38 004861

61 57

39 005598 40 002022

41 002023 42 002024

43 001844 44 004073

45 005234

72mm 120mm 120mm 72mm

20mm

115-120mm

46 001563 47 002025

48 001566 49 001567

50 001568 51 001569

52 001570 53 001571

2021

74 6

54 001572 55 001573

56 004860 57 006342

58 006343

59 006345

60 006344

61 006346 62 006347

63 002028 64 001145

65 002463

ENGLISH (Original instructions)

Explanation of general view

SPECIFICATIONS

Model LS1214/LS1214F/LS1214L

Blade diameter 305 mm

Hole diameter European countries: 30 mm, other than European countries: 25.4 mm

Max. Miter angle Left 47°, Right 52°

Max. Bevel angle Left and Right 45°

Max. Cutting capacities (H x W)

(Note)

* mark indicates that a wood facing with the following thickness is used.

1. Stopper pin

2. Bolt

3. Blade guard

4. Knob

5. Kerf board

6. Saw blade

7. Blade teeth

8. Left bevel cut

9. Straight cut

10. Right bevel cut

11. Adjusting bolt

12. Turn base

13. Top surface of turn base

14. Periphery of blade

15. Guide fence

16. Adjusting screw

17. Stopper arm

18. Lock lever

19. Grip

20. Pointer

21. Miter scale

22. Lever

23. Arm

24. Bevel scale

25. Lock-off button

26. Switch trigger

27. Handle

28. Light

29. Light switch

30. Switch for laser

31. Socket wrench

32. Wrench holder

33. Center cover

34. Hex bolt

35. Blade case

36. Arrow

37. Shaft lock

38. Inner flange

39. Spindle

40. Ring

41. Outer flange

42. Hex bolt (left-handed)

43. Dust nozzle

44. Dust bag

45. Fastener

46. Dust box

47. Cover

48. Button

49. Cylinder part

50. Sawdust

51. Support

52. Sub-fence

53. Sub-fence R

54. Screws

55. Vise rod

56. Screw

57. Vise knob

58. Vise arm

59. Rod

60. Vise plate

61. Vise nut

62. Holder

63. Kerf block

64. Vise

65. Spacer block

66. Aluminum extrusion

67. Spacer blocks

68. Horizontal vise (optional

accessory)

69. Hole

70. Over 15 mm

71. Over 540 mm

72. Cut grooves with blade

73. Hex bolts

74. Triangular rule

75. Pointers

76. Arm holder

77. Right 45° bevel angle adjusting

bolt

78. Left 45° bevel angle adjusting bolt

79. Hex lock nut

80. Workpiece

81. Cutting line

82. Vertical vise

83. Screw to change the movable

range of the adjusting screw

84. Hex wrench

85. Laser line

86. Screwdriver

87. Screw (one piece only)

88. Lens for the laser light

89. Pull out

90. Push

91. Lamp box

92. Fluorescent tube

93. Limit mark

94. Brush holder cap

Miter angle

Bevel angle

45° (left) 0° 45° (right)

0°

*71 mm x 260 mm

66 mm x 305 mm

*120 mm x 270 mm

115 mm x 308 mm

*50 mm x 260 mm

45 mm x 305 mm

45° (left and right)

(left) *71 mm x 155 mm

66 mm x 170 mm

(right) *71 mm x 175 mm

66 mm x 215 mm

*120 mm x 185 mm

115 mm x 218 mm

*50 mm x 175 mm

45 mm x 215 mm

52° (right) –

*120 mm x 160 mm

115 mm x 185 mm

–

No load speed (min

-1

) 3,200

Laser Type (LS1214L only) Red Laser 650 nm, <1 mW (Laser Class 2)

Dimensions (L x W x H) LS1214/LS1214F 723 mm x 520 mm x 696 mm

LS1214L 723 mm x 520 mm x 718 mm

Net weight LS1214: 24.4 kg, LS1214F: 24.6 kg, LS1214L: 25.3 kg

Safety class /II

•Due to our continuing program of research and development, the specifications herein are subject to change without

notice.

•Specifications may differ from country to country.

•Weight according to EPTA-Procedure 01/2003

Symbols

END216-4

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

............... Read instruction manual.

................ DOUBLE INSULATION

................ To avoid injury from flying debris, keep

holding the saw head down, after making

cuts, until the blade has come to a

complete stop.

When performing slide cut, first pull

carriage fully and press down handle,

then push carriage toward the guide

fence.

................ Do not place hand or fingers close to the

blade.

................ For your safety, remove the chips, small

pieces, etc. from the table top before

operation.

........... Always set SUB-FENCE to left position

when performing left bevel cuts. Failure

to do so may cause serious injury to

operator.

.......... Always remove SUB-FENCE R when

performing right bevel cuts. Failure to do

so may cause serious injury to operator.

....... Never look into the laser beam. Direct

laser beam may injure your eyes.

Intended use

ENE006-1

The tool is intended for accurate straight and miter cutting

in wood. With appropriate saw blades, aluminum can also

be sawed.

Power supply

ENF002-1

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

SAFETY INSTRUCTIONS ENA001-2

WARNING! When using electric tools, basic

safety precautions, including the following, should

always be followed to reduce the risk of fire, electric

shock and personal injury. Read all these instructions

before operating this product and save these

instructions.

For safe operations:

1. Keep work area clean.

Cluttered areas and benches invite injuries.

2. Consider work area environment.

Do not expose power tools to rain. Do not use power

tools in damp or wet locations. Keep work area well lit.

Do not use power tools where there is risk to cause

fire or explosion.

3. Guard against electric shock.

Avoid body contact with earthed or grounded surfaces

(e.g. pipes, radiators, ranges, refrigerators).

4. Keep children away.

Do not let visitors touch the tool or extension cord. All

visitors should be kept away from work area.

5. Store idle tools.

When not in use, tools should be stored in a dry, high

or locked up place, out of reach of children.

6. Do not force the tool.

It will do the job better and safer at the rate for which it

was intended.

7. Use the right tool.

Do not force small tools or attachments to do the job of

a heavy duty tool. Do not use tools for purposes not

intended; for example, do not use circular saws to cut

tree limbs or logs.

8. Dress properly.

Do not wear loose clothing or jewellery, they can be

caught in moving parts. Rubber gloves and non-skid

footwear are recommended when working outdoors.

Wear protecting hair covering to contain long hair.

9. Use safety glasses and hearing protection.

Also use face or dust mask if the cutting operation is

dusty.

10. Connect dust extraction equipment.

Miter angle Thickness of wood

0° 20 mm

45° (left and right) 15 mm

52° (right) 15 mm



If devices are provided for the connection of dust

extraction and collection facilities ensure these are

connected and properly used.

11. Do not abuse the cord.

Never carry the tool by the cord or yank it to

disconnect it from the socket. Keep the cord away

from heat, oil and sharp edges.

12. Secure work.

Use clamps or a vice to hold the work. It is safer than

using your hand and it frees both hands to operate the

tool.

13. Do not overreach.

Keep proper footing and balance at all times.

14. Maintain tools with care.

Keep cutting tools sharp and clean for better and safer

performance. Follow instructions for lubrication and

changing accessories. Inspect tool cord periodically

and if damaged have it repaired by an authorized

service facility. Inspect extension cords periodically

and replace, if damaged. Keep handles dry, clean and

free from oil and grease.

15. Disconnect tools.

When not in use, before servicing and when changing

accessories such as blades, bits and cutters.

16. Remove adjusting keys and wrenches.

Form the habit of checking to see that keys and

adjusting wrenches are removed from the tool before

turning it on.

17. Avoid unintentional starting.

Do not carry a plugged-in tool with a finger on the

switch. Ensure switch is off when plugging in.

18. Use outdoor extension leads.

When tool is used outdoors, use only extension cords

intended for outdoor use.

19. Stay alert.

Watch what you are doing. Use common sense. Do

not operate tool when you are tired.

20. Check damaged parts.

Before further use of the tool, a guard or other part

that is damaged should be carefully checked to

determine that it will operate properly and perform its

intended function. Check for alignment of moving

parts, free running of moving parts, breakage of parts,

mounting and any other conditions that may affect its

operation. A guard or other part that is damaged

should be properly repaired or replaced by an

authorized service center unless otherwise indicated

in this instruction manual. Have defective switches

replaced by an authorized service facility. Do not use

the tool if the switch does not turn it on and off.

21. Warning.

The use of any accessory or attachment, other than

those recommended in this instruction manual or the

catalog, may present a risk of personal injury.

22. Have your tool repaired by a qualified person.

This electric tool is in accordance with the relevant

safety requirements. Repairs should only be carried

out by qualified persons using original spare parts,

otherwise this may result in considerable danger to

the user.

ADDITIONAL SAFETY RULES

FOR TOOL

ENB034-3

1. Wear eye protection.

2. Keep hands out of path of saw blade. Avoid

contact with any coasting blade. It can still cause

severe injury.

3. Do not operate saw without guards in place.

Check blade guard for proper closing before each

use. Do not operate saw if blade guard does not

move freely and close instantly. Never clamp or tie

the blade guard into the open position.

4. Do not perform any operation freehand. The

workpiece must be secured firmly against the turn

base and guide fence with the vise during all

operations. Never use your hand to secure the

workpiece.

5. Never reach around saw blade.

6. Turn off tool and w ait for saw blade to stop before

moving workpiece or changing settings.

7. Unplug tool before changing blade or servicing.

8. Always secure all moving portions before carrying

the tool.

9. Stopper pin which locks the cutter head down is

for carrying and storage purposes only and not for

any cutting operations.

10. Do not use the tool in the presence of flammable

liquids or gases.

11. Check the blade carefully for cracks or damage before

operation.

Replace cracked or damaged blade immediately.

12. Use only flanges specified for this tool.

13. Be careful not to damage the arbor, flanges

(especially the installing surface) or bolt. Damage to

these parts could result in blade breakage.

14. Make sure that the turn base is properly secured so it

will not move during operation.

15. For your safety, remove the chips, small pieces, etc.

from the table top before operation.

16. Avoid cutting nails. Inspect for and remove all nails

from the workpiece before operation.

17. Make sure the shaft lock is released before the switch

is turned on.

18. Be sure that the blade does not contact the turn base

in the lowest position.

19. Hold the handle firmly. Be aware that the saw moves

up or down slightly during start-up and stopping.

20. Make sure the blade is not contacting the workpiece

before the switch is turned on.

21. Before using the tool on an actual workpiece, let it run

for a while. Watch for vibration or wobbling that could

indicate poor installation or a poorly balanced blade.

22. Wait until the blade attains full speed before cutting.

23. Stop operation immediately if you notice anything

abnormal.

24. Do not attempt to lock the trigger in the on position.

25. Be alert at all times, especially during repetitive,

monotonous operations. Do not be lulled into a false

sense of security. Blades are extremely unforgiving.

26. Always use accessories recommended in this manual.

Use of improper accessories such as abrasive wheels

may cause an injury.

27. Do not use the saw to cut other than wood,

aluminum or similar materials.

28. Connect miter saws to a dust collecting device

when sawing.

29. Select saw blades in relation to the material to be

cut.

30. Take care when slotting.

31. Replace the kerf board when worn.

32. Do not use saw blades manufactured from high

speed steel.

33. Some dust created from operation contains

chemicals known to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicals are:

•lead from lead-based-painted material and,

•arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals: work in a well ventilated area and

work with approved safety equipment, such as

those dust masks that are specially designed to

filter out microscopic particles.

34. To reduce the emitted noise, always be sure that

the blade is sharp and clean.

35. The operator is adequately trained in the use,

adjustment and operation of the machine.

36. Use correctly sharpened saw blades. Observe the

maximum speed marked on the saw blade.

37. Refrain from removing any cut-offs or other parts

of the workpiece from the cutting area whilst the

tool is running and the saw head is not in the rest

position.

SAVE THESE INSTRUCTIONS.

INSTALLATION

Bench mounting

When the tool is shipped, the handle is locked in the

lowered position by the stopper pin. Release the stopper

pin by lowering the handle slightly and pulling the stopper

pin. (Fig. 1)

This tool should be bolted with four bolts to a level and

stable surface using the bolt holes provided in the tool’s

base. This will help prevent tipping and possible injury.

(Fig. 2)

FUNCTIONAL DESCRIPTION

CAUTION:

•Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Blade guard (Fig. 3)

When lowering the handle, the blade guard rises

automatically. The blade guard returns to its original

position when the cut is completed and the handle is

raised. NEVER DEFEAT OR REMOVE THE BLADE

GUARD OR THE SPRING WHICH ATTACHES TO THE

GUARD.

In the interest of your personal safety, always maintain the

blade guard in good condition. Any irregular operation of

the blade guard should be corrected immediately. Check

to assure spring loaded return action of guard. NEVER

USE THE TOOL IF THE BLADE GUARD OR SPRING

ARE DAMAGED, FAULTY OR REMOVED. DOING SO IS

HIGHLY DANGEROUS AND CAN CAUSE SERIOUS

PERSONAL INJURY.

If the see-through blade guard becomes dirty, or sawdust

adheres to it in such a way that the blade and/or

workpiece is no longer easily visible, unplug the saw and

clean the guard carefully with a damp cloth. Do not use

solvents or any petroleum-based cleaners on the plastic

guard.

If the blade guard is especially dirty and vision through the

guard is impaired, use the supplied socket wrench to

loosen the hex bolt holding the center cover. Loosen the

hex bolt by turning it counterclockwise and raise the blade

guard and center cover. With the blade guard so

positioned, cleaning can be more completely and

efficiently accomplished. When cleaning is complete,

reverse procedure above and secure bolt. Do not remove

spring holding blade guard. If guard becomes discolored

through age or UV light exposure, contact a Makita

service center for a new guard. DO NOT DEFEAT OR

REMOVE GUARD. (Fig. 4)

Positioning kerf board (Fig. 5 & 6)

This tool is provided with the kerf boards in the turn base

to minimize tearing on the exit side of a cut. The kerf

boards are factory adjusted so that the saw blade does

not contact the kerf boards. Before use, adjust the kerf

boards as follows:

First, unplug the tool. Loosen all the screws (2 each on left

and right) securing the kerf boards. Re-tighten them only

to the extent that the kerf boards can still be easily moved

by hand. Lower the handle fully and push in the stopper

pin to lock the handle in the lowered position. Loosen the

knob which secures the slide poles. Pull the carriage

toward you fully. Adjust the kerf boards so that the kerf

boards just contact the sides of the blade teeth. Tighten

the front screws (do not tighten firmly). Push the carriage

toward the guide fence fully and adjust the kerf boards so

that the kerf boards just contact the sides of blade teeth.

Tighten the rear screws (do not tighten firmly).

After adjusting the kerf boards, release the stopper pin

and raise the handle. Then tighten all the screws securely.

CAUTION:

•Before and after changing the bevel angle, always

adjust the kerf boards as described above.

Maintaining maximum cutting capacity

This tool is factory adjusted to provide the maximum

cutting capacity for a 305 mm saw blade.

When installing a new blade, always check the lower limit

position of the blade and if necessary, adjust it as follows:

(Fig. 7 & 8)

First, unplug the tool. Push the carriage toward the guide

fence fully and lower the handle completely. Use the

socket wrench to turn the adjusting bolt until the periphery

of the blade extends slightly below the top surface of the

turn base at the point where the front face of the guide

fence meets the top surface of the turn base.

With the tool unplugged, rotate the blade by hand while

holding the handle all the way down to be sure that the

blade does not contact any part of the lower base. Re-

adjust slightly, if necessary.

CAUTION:

•After installing a new blade, always be sure that the

blade does not contact any part of the lower base when

the handle is lowered completely. Always do this with

the tool unplugged.

Stopper arm (Fig. 9)

The lower limit position of the blade can be easily

adjusted with the stopper arm. To adjust it, rotate the

stopper arm in the direction of the arrow as shown in the

figure. Adjust the adjusting screw so that the blade stops

at the desired position when lowering the handle fully.

Adjusting the miter angle (Fig. 10)

Loosen the grip by turning counterclockwise. Turn the turn

base while pressing down the lock lever. When you have

moved the grip to the position where the pointer points to

the desired angle on the miter scale, securely tighten the

grip clockwise.

CAUTION:

•When turning the turn base, be sure to raise the handle

fully.

•After changing the miter angle, always secure the turn

base by tightening the grip firmly.

Adjusting the bevel angle

To a djus t t he b e v el an g le , l o os en th e l ev er at t he re a r o f

the tool counterclockwise. Unlock the arm by pushing the

handle somewhat strongly in the direction that you intend

to tilt the saw blade. (Fig. 11)

Tilt the saw blade until the pointer points to the desired

angle on the bevel scale. Then tighten the lever clockwise

firmly to secure the arm. (Fig. 12)

CAUTION:

•When tilting the saw blade, be sure to raise the handle

fully.

•After changing the bevel angle, always secure the arm

by tightening the lever clockwise.

•When changing bevel angles, be sure to position the

kerf boards appropriately as explained in the

“Positioning kerf board” section.

Switch action

CAUTION:

•Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

•When not using the tool, remove the lock-off button and

store it in a secure place. This prevents unauthorized

operation.

•Do not pull the switch trigger hard without pressing in

the lock-off button. This can cause switch breakage.

For European countries (Fig. 13)

To p re v en t th e s w it ch tri gg e r fr o m b eing a c c id en ta ll y

pulled, a lock-off button is provided. To start the tool, push

the lever to the left, press in the lock-off button and then

pull the switch trigger. Release the switch trigger to stop.

For all countries other than European countries

(Fig. 14)

To p re v en t th e s w it ch tri gg er f r o m b ei ng ac c id en ta ll y

pulled, a lock-off button is provided. To start the tool, press

in the lock-off button and pull the switch trigger. Release

the switch trigger to stop.

WARNING:

•NEVER use tool without a fully operative switch trigger.

Any tool with an inoperative switch is HIGHLY

DANGEROUS and must be repaired before further

usage.

•For your safety, this tool is equipped with a lock-off

button which prevents the tool from unintended

starting. NEVER use the tool if it runs when you simply

pull the switch trigger without pressing the lock-off

button. Return tool to a Makita service center for proper

repairs BEFORE further usage.

•NEVER tape down or defeat purpose and function of

lock-off button.

Lighting up the lamps

For Model LS1214F only (Fig. 15)

CAUTION:

•This is not a rainproof light. Do not wash the light in

water or use it in a rain or a wet area. Such a conduct

can cause an electric shock and fume.

•Do not touch the lens of the light, as it is very hot while

it is lighted or shortly after it is turned off. This may

cause a burn to a human body.

•Do not apply impact to the light, which may cause

damage or shorted service time to it.

•Do not keep casting the beam of the light to your eyes.

This can cause your eyes to be hurt.

•Do not cover the light with clothes, carton, cardboard or

similar objects while it is lighted, which can cause a fire

or an ignition.

Push the upper position of the switch for turning on the

light and the lower position for off. (Fig. 16)

Move the light to shift an area of lighting.

NOTE:

•Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of light, or it may lower

the illumination.

Laser beam action

For model LS1214L only (Fig. 17)

CAUTION:

•Never look into the laser beam. Direct laser beam may

injure your eyes.

•LASER RADIATION, DO NOT STARE INTO THE

BEAM OR VIEW DIRECTLY WITH OPTICAL

INSTRUMENTS, CLASS 2M LASER PRODUCT.

To t ur n o n th e l a s er be am, p r e ss th e u pp e r p os iti on (I ) of

the switch. Press the lower position (O) to turn off.

Laser line can be shifted to either the left or right side of

the saw blade by adjusting the adjusting screw as follows.

(Fig. 18)

1. Loosen the adjusting screw by turning it

counterclockwise.

2. With the adjusting screw loosened, slide the adjusting

screw to the right or left as far as it goes.

3. Tighten the adjusting screw firmly at the position

where it stops sliding.

Laser line is factory adjusted so that it is positioned within

1 mm from the side surface of the blade (cutting position).

NOTE:

•When laser line is dim and almost or entirely invisible

because of the direct sunlight in the indoor or outdoor

window-by work, relocate the work area to a place not

exposed to the direct sunlight.

Aligning the laser line (Fig. 19)

Laser line can be shifted to either the left or right side of

the blade according to the applications of cutting. Refer to

explanation titled “Laser beam action” regarding its

shifting method.

NOTE:

•Use wood facing against the guide fence when aligning

the cutting line with the laser line at the side of guide

fence in compound cutting (bevel angle 45 degrees

and miter angle right 45 degrees).

A) When you obtain correct size on the left side of

workpiece

•Shift the laser line to the left of the blade.

B) When you obtain correct size on the right side of

workpiece

•Shift the laser line to the right of the blade.

Align the cutting line on your workpiece with the laser line.

ASSEMBLY

CAUTION:

•Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Socket wrench storage (Fig. 20)

The socket wrench is stored as shown in the figure. When

using the socket wrench, pull it out of the wrench holder.

After using the socket wrench, return it to the wrench

holder.

Installing or removing saw blade

CAUTION:

•Always be sure that the tool is switched off and

unplugged before installing or removing the blade.

•Use only the Makita socket wrench provided to install

or remove the blade. Failure to do so may result in

overtightening or insufficient tightening of the hex bolt.

This could cause an injury.

Lock the handle in the raised position by pushing in the

stopper pin. (Fig. 1)

To rem ov e the b la de , use t he s o cke t w re nc h t o lo os en th e

hex bolt holding the center cover by turning it

counterclockwise. Raise the blade guard and center

cover. (Fig. 21)

Press the shaft lock to lock the spindle and use the socket

wrench to loosen the hex bolt clockwise. Then remove the

hex bolt, outer flange and blade. (Fig. 22)

To i ns ta ll th e bla de , mo u nt it c ar e ful ly ont o the s p in dl e ,

making sure that the direction of the arrow on the surface

of the blade matches the direction of the arrow on the

blade case.

Install the outer flange and hex bolt, and then use the

socket wrench to tighten the hex bolt (left-handed)

securely counterclockwise while pressing the shaft lock.

(Fig. 23)

For all countries other than European

countries (Fig. 24)

CAUTION:

•The black ring 25 mm in outer diameter and the silver

ring 25.4 mm in outer diameter are factory-installed as

shown in the figure. When using a blade with 25 mm

hole diameter, replace the silver ring with the black

ring. Before mounting the blade onto the spindle,

always be sure that the correct ring for the arbor hole of

the blade you intend to use is installed between the

inner and outer flanges.

For European countries

CAUTION:

•The ring 30mm in outer diameter is factory-installed

between the inner and outer flanges.

Install the outer flange and hex bolt, and then use the

socket wrench to tighten the hex bolt securely

counterclockwise while pressing the shaft lock.

Return the blade guard and center cover to its original

position. Then tighten the hex bolt clockwise to secure the

center cover. Release the handle from the raised position

by pulling the stopper pin. Lower the handle to make sure

that the blade guard moves properly. Make sure shaft lock

has released spindle before making cut. (Fig. 21)

Dust bag (accessory) (Fig. 25)

The use of the dust bag makes cutting operations clean

and dust collection easy. To attach the dust bag, insert the

dust nozzle into the dust spout on the blade case and fit

the bag’s entry port over the dust nozzle.

When the dust bag is about half full, remove the dust bag

from the tool and pull the fastener out. Empty the dust bag

of its contents, tapping it lightly so as to remove particles

adhering to the insides which might hamper further

collection.

NOTE:

If you connect a vacuum cleaner to your saw, more

efficient and cleaner operations can be performed.

Dust box (accessory) (Fig. 26)

Insert the dust box into the dust nozzle.

Empty the dust box at the earliest possible.

To e mp ty th e d us t b ox , o pe n t he c ove r b y p us hi ng t h e

button and throw away sawdust. Return the cover to the

original position and it locks. Dust box can easily be

removed by pulling out while turning it near the dust

nozzle on the tool.

NOTE:

•If you connect a Makita vacuum cleaner to this tool,

more efficient and cleaner operations can be

performed.

CAUTION:

•Empty the dust box before collected sawdust level

reaches the cylinder part. (Fig. 27 & 28)

Securing workpiece

WARNING:

•It is extremely important to always secure the

workpiece properly and tightly with the vise. Failure to

do so can cause the tool to be damaged and/or the

workpiece to be destroyed. PERSONAL INJURY MAY

ALSO RESULT. Also, after a cutting operation, DO

NOT raise the blade until the blade has come to a

complete stop.

CAUTION:

•When cutting long workpieces, use supports that are as

high as the top surface level of the turn base. Do not

rely solely on the vertical vise and/or horizontal vise to

secure the workpiece.

Thin material tends to sag. Support workpiece over its

entire length to avoid blade pinch and possible

KICKBACK. (Fig. 29)

Sub-fence (Fig. 30)

This tool is equipped with the sub-fence which should

ordinarily be positioned as shown in the figure.

However, when performing left bevel cuts, set it to the left

position as shown in the figure.

CAUTION:

• When performing left bevel cuts, flip the fence over to

the left position as shown in the figure. Otherwise, it will

contact the blade or a part of the tool, causing possible

serious injury to the operator. (Fig. 31)

Sub-fence R (Fig. 32)

The sub-fence R can be installed on the right side of the

guide fence. Insert the rods of the sub-fence R into the

holes in the guide fence. Tighten the screws which come

with the sub-fence R to secure the sub-fence R.

CAUTION:

• When performing right bevel cuts, never use the sub-

fence R. It will contact the blade or a part of the tool,

causing possible serious injury to the operator.

Vertical vise (Fig. 33 & 34)

The vertical vise can be installed in two positions on either

the left or right side of the guide fence. Insert the vise rod

into the hole in the guide fence and tighten the screw on

the back of the guide fence to secure the vise rod.

The vertical vise can also be secured to the rod on the

right side of the sub-fence R.

Position the vise arm according to the thickness and

shape of the workpiece and secure the vise arm by

tightening the screw. If the screw to secure the vise arm

contacts the guide fence, install the screw on the opposite

side of vise arm. Make sure that no part of the tool

contacts the vise when lowering the handle fully and

pulling or pushing the carriage all the way. If some part

contacts the vise, re-position the vise.

Press the workpiece flat against the guide fence and the

turn base. Position the workpiece at the desired cutting

position and secure it firmly by tightening the vise knob.

CAUTION:

•The workpiece must be secured firmly against the turn

base and guide fence with the vise during all

operations.

Horizontal vise (optional accessory)

(Fig. 35)

The horizontal vise can be installed in two positions on

either the left or right side of the base. When performing

15° or greater miter cuts, install the horizontal vise on the

side opposite the direction in which the turn base is to be

turned. (Fig. 36)

By flipping the vise nut to the left, the vise is released, and

rapidly moves in and out. To grip the workpiece, push the

vise knob forward until the vise plate contacts the

workpiece and flip the vise nut to the right. Then turn the

vise knob clockwise to secure the workpiece.

The maximum width of workpiece which can be secured

by the horizontal vise is 200 mm.

When installing the horizontal vise on the right side of the

base, also use the sub-fence R to secure the workpiece

more firmly. Refer to the “Sub-fence R” section described

on previously for installing the sub-fence R.

CAUTION:

•Always rotate the vise nut to the right fully when

securing the workpiece. Failure to do so may result in

insufficient securing of the workpiece. This could cause

the workpiece to be thrown, cause damage to the blade

or cause the loss of control, which can result in

PERSONAL INJURY.

Holders (Fig. 37)

The holders can be installed on either side as a

convenient means of holding workpieces horizontally. Slip

the holder rods into the holes in the base and adjust their

length according to the workpiece to be held. Then tighten

the holders securely with the screws.

CAUTION:

•Always support long workpieces level with the top

surface of the turn base for accurate cuts and to

prevent dangerous loss of control of the tool.

Kerf block (optional accessory) (Fig. 38)

CAUTION:

•When using the kerf block, always cut at the same

miter angle.

•When changing the miter angle, use other kerf blocks.

• When performing bevel cuts, never use the kerf block.

Failure to do so splits the block, causing a serious injury to

operator.

When you use the kerf block at 90° cutting, you can

splinter-free cut in workpiece on the side of the guide

fence (height of the workpiece is up to 35 mm). Install the

kerf block onto the guide fence by means of the two

screws. (Adjust the guide fence and the kerf block so that

they contact their faces. Then tighten the screws

securely.) (Fig. 39)

OPERATION

CAUTION:

•Before use, be sure to release the handle from the

lowered position by pulling the stopper pin.

•Make sure the blade is not contacting the workpiece,

etc. before the switch is turned on.

•Do not apply excessive pressure on the handle when

cutting. Too much force may result in overload of the

motor and/or decreased cutting efficiency. Push down

handle with only as much force as is necessary for

smooth cutting and without significant decrease in

blade speed.

•Gently press down the handle to perform the cut. If the

handle is pressed down with force or if lateral force is

applied, the blade will vibrate and leave a mark (saw

mark) in the workpiece and the precision of the cut will

be impaired.

•During a slide cut, gently push the carriage toward the

guide fence without stopping. If the carriage movement

is stopped during the cut, a mark will be left in the

workpiece and the precision of the cut will be impaired.

1. Press cutting (cutting small workpieces) (Fig. 40)

Workpieces up to 115 mm high and 75 mm wide can be

cut in the following way.

Push the carriage toward the guide fence fully and

tighten the knob clockwise to secure the carriage.

Secure the workpiece with the vise. Switch on the tool

without the blade making any contact and wait until the

blade attains full speed before lowering. Then gently

lower the handle to the fully lowered position to cut the

workpiece. When the cut is completed, switch off the

tool and WAIT UNTIL THE BLADE HAS COME TO A

COMPLETE STOP before returning the blade to its

fully elevated position.

CAUTION:

•Firmly tighten the knob clockwise so that the carriage

will not move during operation. Insufficient tightening

may cause unexpected kickback of the blade. Possible

serious PERSONAL INJURY may result.

2. Slide (push) cutting (cutting wide workpieces)

(Fig. 41)

Loosen the knob counterclockwise so that the carriage

can slide freely. Secure the workpiece with the vise.

Pull the carriage toward you fully. Switch on the tool

without the blade making any contact and wait until the

blade attains full speed. Press down the handle and

PUSH THE CARRIAGE TOWARD THE GUIDE

FENCE AND THROUGH THE WORKPIECE. When

the cut is completed, switch off the tool and WAIT

UNTIL THE BLADE HAS COME TO A COMPLETE

STOP before returning the blade to its fully elevated

position.

CAUTION:

•Whenever performing the slide cut, FIRST PULL THE

CARRIAGE TOWARD YOU FULLY and press down

the handle to the fully lowered position, then PUSH

THE CARRIAGE TOWARD THE GUIDE FENCE.

NEVER START THE CUT WITH THE CARRIAGE NOT

FULLY PULLED TOWARD YOU. If you perform the

slide cut without pulling the carriage fully or if you

perform the slide cut toward your direction, the blade

may kickback unexpectedly with the potential to cause

serious PERSONAL INJURY.

•Never perform the slide cut with the handle locked in

the lowered position by pressing the stopper pin.

•Never loosen the knob which secures the carriage

while the blade is rotating. This may cause serious

injury.

3. Miter cutting

Refer to the previously covered “Adjusting the miter

angle”.

4. Bevel cut (Fig. 42)

Loosen the lever and tilt the saw blade to set the bevel

angle (Refer to the previously covered “Adjusting the

bevel angle”). Be sure to retighten the lever firmly to

secure the selected bevel angle safely. Secure the

workpiece with a vise. Make sure the carriage is pulled

all the way back toward the operator. Switch on the tool

without the blade making any contact and wait until the

blade attains full speed. Then gently lower the handle

to the fully lowered position while applying pressure in

parallel with the blade and PUSH THE CARRIAGE

TOWARD THE GUIDE FENCE TO CUT THE

WORKPIECE. When the cut is completed, switch off

the tool and WAIT UNTIL THE BLADE HAS COME TO

A COMPLETE STOP before returning the blade to its

fully elevated position.

CAUTION:

•Always be sure that the blade will move down to bevel

direction during a bevel cut. Keep hands out of path of

saw blade.

•During a bevel cut, it may create a condition whereby

the piece cut off will come to rest against the side of the

blade. If the blade is raised while the blade is still

rotating, this piece may be caught by the blade,

causing fragments to be scattered which is dangerous.

The blade should be raised ONLY after the blade has

come to a complete stop.

•When pressing down the handle, apply pressure in

parallel with the blade. If a force is applied

perpendicularly to the turn base or if the pressure

direction is changed during a cut, the precision of the

cut will be impaired.

•Always set the sub-fence to the left position when

performing left bevel cuts.

5. Compound cutting

Compound cutting is the process in which a bevel

angle is made at the same time in which a miter angle

is being cut on a workpiece. Compound cutting can be

performed at angle shown in the table.

006484

At the miter angle of left 45° and bevel angle of left 45°,

workpieces up to 66 mm high and 170 mm wide can be

cut.

At the miter angle of right 45° and bevel angle of left

45°, workpieces up to 66 mm high and 215 mm wide

can be cut.

At the miter angle of left and right 45° and bevel angle

of right 45°, workpieces up to 45 mm high and 215 mm

wide can be cut.

When performing compound cutting, refer to “Press

cutting”, “Slide cutting”, “Miter cutting” and “Bevel cut”

explanations.

Miter angle Bevel angle

Left and Right 45° Left and Right 0° - 45°

Left 47° Left 0° - 45° and Right 0° - 40°

Right 52° Left 0° - 30° and Right 0° - 45°

6. Cutting aluminum extrusion (Fig. 43 & 44)

When securing aluminum extrusions, use spacer

blocks or pieces of scrap as shown in the figure to

prevent deformation of the aluminum. Use a cutting

lubricant when cutting the aluminum extrusion to

prevent build-up of the aluminum material on the blade.

CAUTION:

•Never attempt to cut thick or round aluminum

extrusions. Thick aluminum extrusions may come

loose during operation and round aluminum extrusions

cannot be secured firmly with this tool.

7. Wood facing

Use of wood facing helps to assure splinter-free cuts in

workpieces. Attach a wood facing to the guide fence

using the holes in the guide fence and 6 mm screws.

See the figure concerning the dimensions for a

suggested wood facing. (Fig. 45)

CAUTION:

•Use straight wood of even thickness as the wood

facing.

•When cutting workpieces from 115 mm to 120 mm

high, use a wood facing to prevent a portion of the

workpiece near the guide fence from being left uncut.

Example:

When cutting workpieces 120 mm high, use a wood

facing with the following thickness.

006476

CAUTION:

•Use screws to attach the wood facing to the guide

fence. The screws should be installed so that the screw

heads are below the surface of the wood facing.

•When the wood facing is attached, do not turn the turn

base with the handle lowered. The blade and/or the

wood facing will be damaged.

8. Groove cutting (Fig. 46)

A dado type cut can be made by proceeding as follows:

Adjust the lower limit position of the blade using the

adjusting screw and the stopper arm to limit the cutting

depth of the blade. Refer to “Stopper arm” section

described previously.

After adjusting the lower limit position of the blade, cut

parallel grooves across the width of the workpiece

using a slide (push) cut as shown in the figure. Then

remove the workpiece material between the grooves

with a chisel. Do not attempt to perform this type of cut

using wide (thick) blades or with a dado blade. Possible

loss of control and injury may result.

CAUTION:

•Be sure to return the stopper arm to the original

position when performing other than groove cutting.

Carrying tool (Fig. 1)

Make sure that the tool is unplugged. Secure the blade at

0° bevel angle and the turn base at right miter angle fully.

Secure the slide poles after pulling the carriage toward

you fully. Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin.

Carry the tool by holding both sides of the tool base as

shown in the figure. If you remove the holders, dust bag,

etc., you can carry the tool more easily. (Fig. 47)

CAUTION:

•Always secure all moving portions before carrying the

tool.

•Stopper pin is for carrying and storage purposes only

and not for any cutting operations.

MAINTENANCE

CAUTION:

•Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

WARNING:

•Always be sure that the blade is sharp and clean for the

best and safest performance.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

1. Miter angle (Fig. 48)

Push the carriage toward the guide fence and tighten

the knob to secure the carriage.

Loosen the grip which secures the turn base. Turn the

turn base so that the pointer points to 0° on the miter

scale. Then turn the turn base slightly clockwise and

counterclockwise to seat the turn base in the 0° miter

notch. (Leave as it is if the pointer does not point to 0°.)

Loosen the hex bolts securing the guide fence using

the socket wrench.

Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin. Square the side

of the blade with the face of the guide fence using a

triangular rule, try-square, etc. Then securely tighten

the hex bolts on the guide fence in the order from the

right side. (Fig. 49)

Make sure that the pointer points to 0° on the miter

scale. If the pointer does not point to 0°, loosen the

screw which secures the pointer and adjust the pointer

so that it will point to 0°. (Fig. 50)

2. Bevel angle

(1) 0° bevel angle (Fig. 51)

Push the carriage toward the guide fence and

tighten the knob to secure the carriage. Lower the

handle fully and lock it in the lowered position by

pushing in the stopper pin. Loosen the lever at the

rear of the tool. Make sure that the arm is locked.

Turn the hex bolt on the left side of the arm two or

three revolutions counterclockwise. Turn the hex

bolt on the right side of the arm two or three

revolutions counterclockwise to tilt the blade to the

left. (Fig. 52)

Carefully square the side of the blade with the top

surface of the turn base using the triangular rule,

try-square, etc. by turning the hex bolt on the right

side of the arm clockwise. Turn the hex bolt on the

left side of the arm clockwise as far as it will go.

Then tighten the lever securely. (Fig. 53)

Miter angle Bevel angle

0° Over 20 mm

Left and Right 45° Over 15 mm

Right 52° Over 15 mm

Make sure that the two pointers on the arm point to

each 0° on the bevel scale on the arm holder. If they

do not point to 0°, loosen the screws which secure

the pointers and adjust them so that they will point

to 0°. (Fig. 54)

(2) 45° bevel angle (Fig. 55)

Adjust the 45° bevel angle only after performing 0°

bevel angle adjustment. To adjust left 45° bevel

angle, loosen the lever and tilt the blade to the left

fully. Make sure that the pointer on the arm points to

45° on the bevel scale on the arm holder. If the

pointer does not point to 45°, turn the left 45° bevel

angle adjusting bolt on the side of the arm holder

until the pointer points to 45°.

To a dj ust ri ght 4 5 ° be v el a n gle , p erf orm t he sa me

procedure described above.

Adjusting for smooth beveling action

(Fig. 56)

The hex lock nut holding together the arm and arm holder

has been factory adjusted to assure smooth beveling

action and to guarantee precise cutting. Do not tamper

with it. Should looseness develop at the arm and arm

holder connection, tighten the hex lock nut using a

wrench.

Adjusting the position of laser line

For model LS1214L only (Fig. 57 & 58)

WARNING:

•As the tool is plugged when adjusting the position of

laser line, take a full caution especially at switch action.

Pulling the switch trigger accidentally cause an

accidental start of the tool and personal injury.

CAUTION:

•Never look into the laser beam directly. Direct laser

beam causes damage to your eyes.

•Never apply a blow or impact to the tool. A blow or

impact causes the incorrect position of laser line,

damage to the laser beam emitting part or a short life of

the tool.

When adjusting the laser line appears on the left side

of the saw blade (Fig. 59)

When adjusting the laser line appears on the right

side of the saw blade (Fig. 60)

For both adjustments, do as follows.

1. Make sure that the tool is unplugged.

2. Draw the cutting line on the workpiece and place it on

the turn table. At this time, do not secure the

workpiece with a vise or similar securing device.

3. Lower the blade by lowering the handle and just check

to see where the cutting line and the position of the

saw blade is. (Decide which position to cut on the line

of cut.)

4. After decision the position to be cut, return the handle

to the original position. Secure the workpiece with the

vertical vise without shifting the workpiece from the

pre-checked position.

5. Plug the tool and turn on the laser switch.

6. Adjust the position of laser line as follows.

The position of laser line can be changed as the movable

range of the adjusting screw for the laser is changed by

turning two screws with a hex wrench. (The movable

range of laser line is factory adjusted within 1 mm from the

side surface of blade.)

To s hi ft t he la se r lin e m o va bl e ra n g e f ur th er a wa y f ro m

the side surface of blade, turn the two screws

counterclockwise after loosening the adjusting screw.

Turn these two screws clockwise to shift it closer to the

side surface of the blade after loosening the adjusting

screw.

Refer to the section titled “Laser beam action” and adjust

the adjusting screw so that the cutting line on your

workpiece is aligned with the laser line.

NOTE:

•Check the position of laser line regularly for accuracy.

•Have the tool repaired by Makita authorized service

center for any failure on the laser unit.

Cleaning of the lens for the laser light

For model LS1214L only (Fig. 61)

If the lens for the laser light becomes dirty, or sawdust

adheres to it in such a way that the laser line is no longer

easily visible, unplug the saw and remove and clean the

lens for the laser light carefully with a damp, soft cloth. Do

not use solvents or any petroleum-based cleaners on the

lens. (Fig. 62)

To r em ov e t he le ns f o r t he la se r l ig h t, r em ov e the s a w

blade before removing the lens according to the

instructions in the section titled “Installing or removing

saw blade”.

Loosen but do not remove the screw which secures the

lens using a screwdriver.

Pull out the lens as shown in the figure.

NOTE:

•If the lens does not come out, loosen the screw further

and pull out the lens again without removing the screw.

Replacing fluorescent tube

For LS1214F only (Fig. 63)

CAUTION:

•Always be sure that the tool is switched off and

unplugged before replacing the fluorescent tube.

•Do not apply force, impact or scratch to a fluorescent

tube, which can cause a glass of the fluorescent tube

to be broken resulting in a injury to you or your

bystanders.

•Leave the florescent tube for a while immediately after

a use of it and then replace it. If not, you may burn

yourself.

Remove screws, which secure lamp box for the light.

Pull out the lamp box keeping pushing lightly the upper

position of it as illustrated on the left.

Pull out the fluorescent tube and then replace it with

Makita original new one.

Replacing carbon brushes (Fig. 64)

Remove and check the carbon brushes regularly. Replace

when they wear down to the limit mark. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes.

Leht laaditakse ...

Makita LS1214F Kasutusjuhend

Kaubamärk: Makita

Mudel: LS1214F

Kategooria: Leegisaed

Tüüp: Kasutusjuhend

See juhend sobib ka

Laadige alla PDF

aruanne

Makita LS1214F Kasutusjuhend

See juhend sobib ka

Makita LS1214F Kasutusjuhend

Seotud paberid

Muud dokumendid