Whirlpool AKR 657 WH Kasutusjuhend

Bränd: Whirlpool

Mudel: AKR 657 WH

Kategooria: Pliidikubud

Tüüp: Kasutusjuhend

See käsiraamat sobib ka

5019 318 33316

INSTALLATION OCH ANVÄNDNING

Notering för installation: Avståndet mellan kokkärl och nedre delen av fläkten får inte vara under 50 cm för

elektriska plattor, och minst 65 cm för gasplattor, eller blandade plattor.

Om ett större avstånd än det här specificerade anges i installationsanvisningarna som medföljer gasspisen är det

detta avstånd som gäller.

VARNING: Produkt med hög vikt. För flyttning och installation av fläktkåpan krävs minst två personer.

Notering för installation och användning: Innan du installerar eller använder fläktkåpan, läs manualen

noggrant. Tillverkaren kan inte ställas till svars för eventuella fel, skador eller bränder orskade på apparaten som

uppstått på grund av underlåtenhet att iaktta anvisningarna i denna manual.

Anslutningen av fläktkåpan måste göras av en kvalificerad fackman. Installatören skall respektera de

installationsavstånd som står specificerade i typskylten på modellen/serien.

INSTALLASJON OG BRUK

Anmerkning om installasjon: Minimumsavstanden mellom varmesonene på kokeapparatet og undersiden av

kjøkkenventilatoren må ikke være mindre enn 50 cm for elektriske komfyrer og 65 cm for gasskomfyrer og

kombinasjonskomfyrer.

Dersom installasjonsveiledningen for gassapparatet krever en større avstand enn den som er oppgitt, må denne

avstanden overholdes.

ADVARSEL: Dette produktet er svært tungt. Flytting og installasjon av kjøkkenventilatoren må derfor

utføres av to eller flere personer.

Anmerkning om installasjon og bruk: Før installasjon og bruk av ventilatoren må du lese denne

bruksveiledningen nøye. Produsenten fraskriver seg ethvert ansvar for eventuelle problemer, skader eller brann

på apparatet som skyldes at instruksene i denne bruksanvisningen ikke følges.

Installasjon av ventilatoren skal utføres av en autorisert elektriker. Installatøren må respektere

installasjonsavstandene som anvist på typeskiltet til modellen/serien.

INSTALLATION OG BRUG

Bemærkning vedrørende monteringen: Minimumafstanden mellem komfurets øverste del og emhættens

nederste del skal være på mindst 50 cm for elkomfurer og 65 cm for gaskomfurer eller el-/gaskomfurer.

Hvis installationsvejledningen for gaskogezonen/gaskomfuret angiver en afstand, der er større end den anførte

afstand, skal den største afstand overholdes.

ADVARSEL: Da apparatet har meget stor vægt, skal flytning og montering af emhætten foretages af mindst

to eller flere personer.

Bemærk inden installation og brug: Læs denne vejledning inden installation og brug af emhætten.

Producenten fralægger sig ethvert ansvar for eventuelle problemer, skader eller brande i apparatet, der skyldes

manglende overholdelse af anvisningerne i denne håndbog.

Emhætten skal installeres af en faguddannet tekniker. Installatøren skal overholde de installationsafstande, der er

specificeret på typepladen for modellen/serien.

5019 318 33316

ASENNUS JA KÄYTTÖ

Asennusta koskeva huomautus: Minimietäisyys liedellä olevan keittoastioiden alustan ja liesituulettimen

alareunan välillä EI SAA OLLA ALLE 50 cm kun kyseessä on sähköliesi ja 65 cm kun kyseessä on kaasu- tai

sekaliesi.

Jos kaasulieden asennusohjeissa määrätään yllä mainittua etäisyyttä suurempi etäisyys, noudata sitä.

VAROITUS: Liesituuletin on painava, ja sen siirtämisessä ja asennuksessa tarvitaan vähintään kaksi henkilöä.

Asennusta ja käyttöä koskeva huomautus: Lue tämä käyttöopas huolellisesti ennen liesituulettimen

asennusta ja käyttöä. Valmistaja ei vastaa yllä mainittujen ohjeiden noudattamisen laiminlyönnistä johtuneesta

laitteen aiheuttamasta ongelmasta, vahingosta tai tulipalosta.

Liesituulettimen asennuksen saa tehdä ainoastaan pätevä teknikko. Asentajan täytyy noudattaa mallin/sarjan

arvokilvessä olevia asennusta koskevia etäisyyksiä.

INSTALLATION AND USE

For installation: The minimum distance between the support surface of the recipients on the cooking device

and the lowest part of the hood must not be less than 50 cm in the case of electric cookers and 65 cm for gas or

combination cookers. If the installation instructions for the gas cooker specify a greater distance, this must be

taken into account.

WARNING: Very heavy product; hood handling and installation must be carried out by at least two persons.

Note on installation and use: Read this manual before installing or using the hood. The Manufacturer declines

all liability for any faults, damage or fires caused by the appliance as a result of failure to observe the instructions

and recommendations given in this manual.

This hood must be installed by a qualified technician. The installer must observe the installation distances

indicated on the rating plate of the product/range.

FIN

5019 318 33316

* endast på vissa modeller

* kun på noen modeller

* Findes kun på nogle modeller

* vain joissain malleissa

* only present on some models

5019 318 33316

Fettfilter

Fedtfilter

Rasvasuodatin

Grease filter

Kolfilter

Kullfilter

Hiilisuodatin

Carbon filter

5019 318 33316

SAFEGUARDING THE ENVIRONMENT

1. Packing

Packing materials are 100% recyclable and are marked with the

recycling symbol .Comply with the local regulations for

disposal. The packing materials (plastic bags, polystyrene, etc.)

are a potential source of danger and must be kept out of the

reach of children.

2. Product

This appliance is marked in compliance with European Directive

2002/96/EC, Waste Electrical and Electronic Equipment (WEEE).

By ensuring that this appliance is correctly scrapped, the user can

help prevent potentially harmful consequences for the

environment and the health of people.

The symbol on the product or the accompanying

documentation indicates that this product should not be treated

as domestic waste but must be taken to a suitable collection

centre for the recycling of electrical and electronic equipment.

Disposal must be carried out in compliance with local regulations

on waste disposal.

For further information on the treatment, recovery and recycling

of this product, contact the competent local office, the

household waste collection service or the shop where you

purchased the appliance.

IMPORTANT INSTRUCTIONS FOR

SAFETY

WARNING: To reduce the risk of accidents, electric shock,

injury or damage, when using the hood comply with the basic

precautions, including the following.

1. Always disconnect the hood from the power supply before

carrying out any installation or maintenance operation on the

appliance.

2. Installation must be carried out by a specialised technician, in

compliance with the manufacturer’s instructions and local

safety regulations.

3. Earthing of the appliance is compulsory. (Not possible for

Class II hoods).

4. Never use multisockets and extension leads.

5. The electrical components must no longer be accessible to

the user after installation.

6. Do not touch the hood with wet parts of the body or use it

when barefoot.

7. Do not pull the appliance power cable to unplug it.

8. After-sales service – do not repair or replace any part of the

hood unless specifically indicated in the manual. All other

maintenance services must be carried out by a specialised

technician.

9. When drilling the wall, make sure not to damage the

electrical connections and/or pipes.

10. The ventilation ducts must always discharge to the outside.

11. The Manufacturer declines any liability for improper use or

incorrect setting of the controls.

12. The appliance is not intended for use by children or persons

with limited physical, sensory or mental abilities or without

experience and knowledge of it, unless they are under the

supervision of or instructed in its use by a person responsible

for their safety.

13. Keep children away.

14. To reduce the risk of fire, only use a metal inlet duct.

15. Children must be supervised so that they do not play with

the appliance.

16. The product must be disposed of in compliance with local

regulations on waste disposal.

17. For further information on the treatment, recovery and

recycling of this product, contact the competent local office,

the household waste collection service or the shop where

you purchased the appliance.

18. Regular cleaning and maintenance is essential for correct

hood operation and good performance. Frequently clean all

encrustations from dirty surfaces to prevent the

accumulation of grease. Regularly clean or replace filters.

19. Do not “flambé” food under the hood. Naked flames could

cause a fire.

20. The room must have adequate ventilation when the hood is

used at the same time as appliances operating on gas or

other fuels.

21. The discharge air must not be eliminated in a duct used to

remove fumes produced by appliances operating on gas or

other fuels, but must have a separate outlet. All the national

regulations on air discharge envisaged by art. 7.12.1 of CEI

EN 60335-2-31 must be observed.

22. If the hood is used together with other appliances operating

on gas or other fuels, the negative pressure in the room

must not exceed 4 Pa (4 x 10

-5

bar). Therefore, make sure

the room is adequately ventilated.

23. Do not leave pans unattended when frying, since the cooking

oil could catch fire.

24. Make sure the lamps are cold before touching them.

25. The hood is not a shelf, therefore do not overload or place

objects on it.

26. Do not use or leave the hood without its lamps correctly

installed - risk of electric shock.

27. Wear work gloves for all installation and maintenance

operations.

28. The product is not suitable for outdoor use.

29. The air sucked by the hood must not be eliminated through

the same flue of the heating system or other appliances using

gas or other fuels.

FIN

S N DK

5019 318 33316

Electrical connection

The mains voltage must match that given on the rating plate

located inside the hood. If provided with a plug, connect the

hood to a socket complying with the current regulations and

located in an accessible area. If it does not have a plug (direct

connection to the power supply) or if the plug is not in an

accessible place, fit a suitable double-pole switch that ensures

complete disconnection from the power supply in category III

overvoltage conditions, complying with the installation rules.

WARNING: Power cable replacement must be carried out

by an authorised Service Centre or a qualified person.

WARNING: Before reconnecting the hood circuit to the

power supply and checking correct operation, always make sure

the power cable is correctly fitted and that it was NOT crushed

in its housing during installation. Make sure to have this operation

carried out by a specialised technician.

Cleaning the hood

WARNING! Failure to remove oil/grease (at least once a

month) could result in fire.

Use a soft cloth with a neutral detergent. Never use abrasive

substances or alcohol.

Before using the hood

Please read these instructions carefully and keep them for future

reference, in order to ensure best use of your hood.

The packing materials (plastic bags, polystyrene, etc.) are a

potential source of danger and must be kept out of the reach of

children.

Make sure the hood has not been damaged during transport.

Declaration of conformity

This product has been designed, manufactured and put on the

market in conformity with:

- safety objectives of the “Low Voltage” Directive 2006/95/EC

(which replaces 73/23/EEC as amended)

- protection requirements of “EMC” Directive 89/336/EEC

amended by Directive 93/68/EEC.

Troubleshooting guide

If the hood does not work:

• Is the plug properly inserted in the power socket?

• Is there a power failure?

If the hood is not extracting enough:

• Is the right speed selected?

• Do the filters need cleaning or replacing?

• Are the air outlets blocked?

If the lamp does not work:

• Does the lamp need replacing?

• Is the lamp correctly fitted?

AFTER-SALES SERVICE

Before calling the After-Sales Service

1. Check to see if you can fix the problem yourself (see

“Troubleshooting Guide”).

2. Switch the appliance off and then on again to check if the

problem has been eliminated.

3. If the problem persists, contact the After-Sales Service.

Specify:

• the type of fault,

• the product model given on the dataplate inside the hood,

visible on removing the grease filters,

• your full address,

• your telephone number and area code,

• the Service code (the number under the word SERVICE on

the dataplate inside the hood, behind the grease filter).

If any repairs are necessary, contact an authorised Service Centre

(to ensure the use of original spare parts and correct repair).

Failure to comply with these instructions can compromise the

safety and quality of the product.

FIN

S N DK

5019 318 33316

Extractor hood installation (A): fumes are extracted and expelled to the outside through an exhaust duct fixed to the flange

C (bayonet coupling). Always shut off the unused exhaust outlet with the plug D1 provided (if provided- bayonet coupling).

Important: Some models are supplied with the upper hole B1 closed: Press hard to detach the knockout part closing the

discharge hole and remove it; this part can no longer be refitted, therefore carry out the operation described only when sure of

the type of installation required.

Important! In some models, in order to use the rear exhaust outlet B2 the plastic part D2 or D3 must be removed first.

Use pliers and a cutter to remove it.

Filter version installation (F): If it is not possible to duct fumes and steam to the outside, the hood can be used in the filter

version by fitting a carbon filter/s (not supplied). In this way, fumes and steam are recycled through the front grille section

positioned above the control panel.

Check the position of the extraction/filter selector (inside the hood) G.

Fixing to the wall - Place the hood against the wall (or use the template H, if provided) and, using a pencil, mark the holes

(3 or 4 Ø 8mm holes), drill them, insert the rawlplugs J in the holes and 2 screws K in the top holes. Remove the grille and hang

the hood on the 2 screws. Next, from inside, insert the third (and fourth) screws L and screw them all down.

Fixing to the wall unit - Position the hood (or use the template H, if provided) and, using a pencil, mark the 4 Ø 6 mm holes

to be drilled on the bottom of the wall unit.

Fix the hood in place with 4 screws M from inside the wall unit.

Control panel

Light: move the switch to the right or press the next button to switch on.

Extraction speed: move the switch to the right or press the next button to increase extraction speed.

Grease filter - can be one of the following types:

Paper filter: must be replaced once a month or, if the top side is coloured, when the colour shows through the holes in the

grille.

Metal filter: must be washed once a month by hand or in a dishwasher, using a quick wash cycle with a low temperature.

To access the grease filter open the grille using the spring release catches E1 or E2 or E3 and release it from the retainers R1

or R2.

The self-supporting metallic filter has no support grille. To remove it, pull the spring release handlesE1 backwards and

remove the filter downwards.

Important! Over time, the metallic filter may become opaque; this in no way affects its filtering capacity.

Carbon filter - can be one of the following types:

Shaped V1: Remove the cover W by turning the knobs O

through 90°.

Insert the carbon filter inside the special housing and secure it in place by turning the knob O through 90°, then close the cover.

Replace every 4 months.

Rectangular V2: insert the rear edge first T and then the front (U) - replace every 6 months.

Circular V3: Bayonet coupling. Position the filter in the centre so that it covers the motor-protection grille, make sure that

the reference mark X1 or X2 or X3 or X4 on the carbon filter is aligned with the the reference mark Y on the fan shroud,

then turn clockwise; to remove, turn anti-clockwise, if provided with a tab Z remember to lift it up slightly first. Replace every

4 months.

Replacing the bulb/s - Remove the filters then remove the burnt-out bulb (E14 incandescent bulb, 40 W max). Refit the

filters.

G4 halogen bulb, 20 W max: use a small screwdriver or similar suitable tool to prise off.

Replace the bulb cover so that it clicks into position.

FIN

S N DK

Whirlpool AKR 657 WH Kasutusjuhend

Bränd: Whirlpool

Mudel: AKR 657 WH

Kategooria: Pliidikubud

Tüüp: Kasutusjuhend

See käsiraamat sobib ka

Laadige alla PDF

aruanne

teistes keeltes

English: Whirlpool AKR 657 WH User guide
dansk: Whirlpool AKR 657 WH Brugervejledning

Whirlpool AKR 657 WH Kasutusjuhend

See käsiraamat sobib ka

Whirlpool AKR 657 WH Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid