Lenoxx HT-391 Kasutusjuhend

Lenoxx
Bränd
Lenoxx
Mudel
HT-391
Kategooria
Kõlarikomplektid
Tüüp
Kasutusjuhend
IB-HT391-WM-E-073003
PLEASE READ CAREFULLY BEFORE USE
Home Theater System
MODEL HT-391
Turns Your DVD Player Into a 5.1 Channel
Home Theater Surround Sound System
•
Just add your TV & DVD player; everything else is in the box.
•
Incredible surround sound, perfect for DVD viewing & enhanced TV game experience.
•
Also provides superior sound for computer system
The Perfect Sound System for Your DVD Player
IB-HT391-WM-E-073003
1
SAFETY INSTRUCTIONS
CAUTION
FCC Regulations state that unauthorized
changes or modifications to this equipment
may void the user’s authority to operate it.
FCC NOTE
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures.
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment
and receiver.
-Connect this equipment into an outlet on a
circuit different from that to which the receiver
is connected.
-consult the dealer or an experienced radio/
TV technician for help.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THE PLUG WITH
AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO
PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
1.Read these instructions.
2.Keep these instructions.
3.Heed all warnings.
4.Follow all instructions.
5.Do not use this apparatus near water.
6.Clean only with dry cloth.
7.Do not block any ventilation openings, install in accordance with the
manufacturer’s instructions.
8.Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9.Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or
the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
10.Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11.Only use attachments/accessories specified by the manufacturer.
12.Unplug this apparatus during lightning storms or when unused for long
periods of time.
13.Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.
14.This appliance shall not be exposed to dripping or splashing water and
that no object filled with liquid such as vases shall be placed on the
apparatus.
WARNING
IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with
arrowhead symbol, within an
equilateral triangle, is intended
to alert the user to the presence
of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of
sufficient magnitude to
constitute a risk of electric
shock to persons.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
Do not apply oil or petroleum products or solvents to any part of this set.
PRECAUTIONS
ON SAFETY
Should any solid object or liquid fall into the
Home Theater System, unplug the player, and
have it checked by qualified personnel before
operating it any further.
ON PLACEMENT OF YOUR HOME
THEATER SYSTEM
Cleaning the Cabinet
Clean the cabinet and controls with a very dry or slightly moistened soft
cloth. Do not use any type of abrasive pad, scouring powder, or solvents,
such as alcohol or benzene.
•
Do not leave the Home Theater in a location
near a heat source, or in a place subject to
direct sunlight, excessively dusty rooms or
rooms with very high humidity.
•
Do not place the Home Theater system on
an inclined or unstable place.
•
Do not place anything within 1 inch of the sides
or 2 inches from the back of the cabinet. The
heat sink fins must not be covered for the
set to operate properly and prolong the life
of its components.
SEE BOTTOM OF THE MAIN SET.
SEE BOTTOM OF THE MAIN SET.
AC ~ 120V 60Hz
POWER CONSUMPTION:
100 Watts
MADE IN CHINA
IB-HT391-WM-E-073003
INTRODUCTION
All of the adjustable system settings have been preset at our factory for normal operation of the system. All you have to do is to
sit back and enjoy the great home theater experience.
Later on, you may want to change some of the optional settings like speaker volume and balance settings. Instructions for
changing them, are found later in this manual.
This system was designed to provide you with many years of reliable operation with a minimum of care and maintenance. Every
component in your system was perfect when it left our factory. If you experience any problem with the set-up or operation of this
system, please review the Trouble Shooting Guide at the end of this manual before you contact the Customer Service Department
at 1-800-315-5885.
Thank you for purchasing this 5.1 Channel Home Theater Surround Sound System. This deluxe audio theater system turns your
home into a virtual theater. In addition to the incredible surround sound of a 5.1 channel audio source, such as your current DVD
player, this system also superbly enhances your other audio sources, such as a CD player, computer, VCR, or a cassette deck.
The only thing you need to add is your own TV or other devices. We have designed this system to be easy to set up, but please,
review this manual before you operate your system. Please have it handy while you are setting the system up; and keep it
available for future reference, or in the unlikely event that you encounter any unexpected questions or problems. We have tried
to keep this manual as simple as possible. It begins with how to connect the speakers, your TV, and other optional devices. It also
includes instructions on how to position the speakers for the most natural surround sound. If you follow the instructions carefully
you can have the system set up in about an hour.
Basic Features & Benefits of this 5.1 Channel Home Theater System:
2
1.5.1 channel audio decoder for home theater surround sound.
2.TV Game / Video Camera input jacks.
3.Includes audio inputs for DVD, AUX and GAME/CAMERA.
4.Customizable speaker level controls with indicators.
5.Powerful subwoofer provides real BOOM in your bass.
6.Deluxe easy-to-use remote control with batteries included.
7.LED indicators for DVD, AUXILIARY or GAME functions.
8.Designed for easy, mistake-proof color-coded speaker setup.
9.Compatible with computer sound system.
THIS SYSTEM CONTAINS
1 Remote Control
1 Main Set (Subwoofer)
5 Satellite Speakers
2 “AAA” batteries
1 Set of Audio Cables
for DVD or AUX IN
(Red & White)
1 Yellow
Video Cable
1 Set of Audio cables with green
3.5mm plug for Computer
Connection (or other Source
with 3.5mm Jack)
1 Spare
Fuse
IB-HT391-WM-E-073003
•Getting Started
Safety Instructions-------------------------------------------------------------------------------------------------------------------------------------1
Introduction-----------------------------------------------------------------------------------------------------------------------------------------------2
Location of Controls-----------------------------------------------------------------------------------------------------------------------------------4,5
Remote Control Operation---------------------------------------------------------------------------------------------------------------------------6
•Connections
Choose Your Connection-----------------------------------------------------------------------------------------------------------------------------7
Cables Needed to Connect Components to Your Home Theater System --------------------------------------------------------7
Speaker system connections:
Speaker system connections----------------------------------------------------------------------------------------------------------------------8,9
Speaker Positioning Information------------------------------------------------------------------------------------------------------------------10,11
TV Connections ----------------------------------------------------------------------------------------------------------------------------------------12
TV + DVD Connections -----------------------------------------------------------------------------------------------------------------------------13
TV + VCR Connections -----------------------------------------------------------------------------------------------------------------------------14
TV + VCR + Satellite Receiver Connections ------------------------------------------------------------------------------------------------15
TV + TV Game Connections ----------------------------------------------------------------------------------------------------------------------16
TV + Video Camera Connections ----------------------------------------------------------------------------------------------------------------17
AUX IN Connections ---------------------------------------------------------------------------------------------------------------------------------18
AM/FM Tuner Connections ------------------------------------------------------------------------------------------------------------------------19
Computer Sound Connections -------------------------------------------------------------------------------------------------------------------- 20
Amplifier in Main Unit
General ----------------------------------------------------------------------------------------------------------------------------------------------------21
Volume Adjustment-------------------------------------------------------------------------------------------------------------------------------------22
• Listening Mode
5.1 Channel and Stereo Modes ------------------------------------------------------------------------------ ------------------------------------23
•Trouble Shooting ------------------------------------------------------------------------------------------------------------------------24
•Specifications -------------------------------------------------------------------------------------------------------------------------------25
3
TABLE OF CONTENTS
IB-HT391-WM-E-073003
LOCATION OF CONTROLS
4
FRONT OF MAIN SET (SUBWOOFER)
1.ON / STANDBY button - Press to switch the set to on or to standby mode.
2.INPUT SOURCE button - Press several times to select the sound input
source you want: DVD, AUX or GAME.
3.SPEAKER CHANNELS button - Press to select 2 channel or 5.1
channel listening mode.
4.VOLUME UP button - Increases the volume level of all speakers.
5.VOLUME DOWN button - Decreases the volume level of all speakers.
6.REMOTE SENSOR - Receives the signal from the REMOTE CONTROL
(aim the REMOTE control towards this sensor).
7.STANDBY indicator - This indicator has 2 modes: flashing and steadily
on (slow flashing indicates the set is in standby, steadily on indicates the
set is on). When the set is off (standby),pressing the ON/STANDBY
button on the main set or on the REMOTE CONTROL will turn the set on,
the indicator will become steadily on.
NOTE: The rear main power switch must be ON.
8.DVD indicator - For DVD sound use, press the INPUT SOURCE button
on the main set till this lights or press the SOURCE button on your
REMOTE control till this lights.
9.AUX indicator - For AUX IN sound use, press the INPUT SOURCE
button on the main set till this lights or press the SOURCE button on your
REMOTE control.
10.GAME indicator - For TV GAME or VIDEO CAMERA use, press the
INPUT SOURCE button on the main set till this lights or press the
SOURCE button on your REMOTE control.
11.2 CHANNEL indicator - When the listening mode is 2 channel, this
indicator will light up. To change, press the SPEAKER CHANNELS button.
12.5.1 CHANNEL indicator - When the listening mode is 5.1 channel, this
indicator will light up. To change, press the SPEAKER CHANNELS button.
13.VOLUME MAX. indicator - This indicator lights up when the MASTER
VOLUME is at its maximum level, also it will flash confirming you
pressed the VOLUME UP button of either the SUBWOOFER, or
CENTER, or REAR, or the MASTER.
14.VOLUME MIN. indicator - This indicator lights up when the MASTER
VOLUME is at its minium level, also it will flash confirming you pressed
the VOLUME DOWN button of either the SUBWOOFER, or CENTER,
or REAR, or the MASTER.
2
1
3
4
5
6
7
8
14
9
10
11
12
BACK OF MAIN SET (SUBWOOFER)
15. DVD AUDIO INPUT jacks - Connect to the audio output of a DVD player
to have 5.1 channel surround sound.
16.AUX INPUT jack - Connect to the audio output of a tape deck or other
component’s output.
17.GAME AUDIO INPUT jacks - Connect to the audio output jack of a TV
game or video camera.
18.VIDEO INPUT jack - For connection of a video signal from a TV
game, or video camera, or other source.
19.VIDEO OUT jack - Connect to your TV’s video input jack. (If your TV has
no VIDEO jack, you have to buy a VIDEO RF MODULATOR.)
20.FRONT RIGHT SPEAKER jacks - Connect the FRONT RIGHT SPEAKER
to the red and black terminals.
21.FRONT LEFT SPEAKER jacks - Connect the FRONT LEFT SPEAKER
to the red and black terminals.
22.CENTER SPEAKER jacks - Connect only the CENTER SPEAKER to the
blue and black terminals.
23.REAR RIGHT SPEAKER jacks - Connect the REAR RIGHT SPEAKER
to the grey and black terminals.
24.REAR LEFT SPEAKER jacks - Connect the REAR LEFT SPEAKER
to the grey and black terminals.
25.POWER switch - Press to power the set on or off.
NOTE: This switch must be ON in order to be able to use the ON/STANDBY
button on the front of the main set or on the REMOTE CONTROL.
26. FUSE HOLDER with screw cover.
27.AC LINE CORD - Connect to a 120V/60Hz AC standard wall outlet.
15
17
19
24
27
25
21
20
18
16
13
22
21
26
20
22
23
24
23
IB-HT391-WM-E-073003
REMOTE CONTROL
1
2
3
46
5
7
8
9
10
1.IR DIODE - Sends the signal to the set. Do not block or cover this.
2.ON/STANDBY button - Switches the player from STANDBY to ON
or ON to STANDBY (if the main POWER of the set is ON).
3.SOURCE button - Press to select the sound input source you want:
DVD, AUX or GAME.
4.RESET button - Press to adjust all speakers’ output to the factory’s
default settings.
5.MUTE button - Instantly turns off the sound. Press again to restore the
sound.
6.SPEAKER CHANNELS button - Press to select 2 channel or 5.1
channel listening mode.
7.SUBWOOFER UP & DOWN VOLUME button - Press to adjust the
individual SUBWOOFER’s sound level.
8.CENTER UP & DOWN VOLUME button - Press to adjust the
individual CENTER speaker’s sound level.
9.REAR button - Press to adjust the REAR LEFT/RIGHT speakers’ sound
level.
10. MASTER VOLUME UP & DOWN button - Press to adjust the sound
level of all speakers.
LOCATION OF CONTROLS
5
SEE NEXT PAGE FOR REMOTE CONTROL BATTERY INSTALLATION.
IB-HT391-WM-E-073003
REMOTE CONTROL OPERATION
Remove the BATTERY COMPARTMENT DOOR of the REMOTE
CONTROL and insert 2 size “AAA” alkaline batteries (included)
according to the and markings inside the BATTERY
COMPARTMENT of the REMOTE CONTROL unit.
Tips on Battery Use
Battery Installation Remote Control Operating Range
Point the REMOTE CONTROL unit within 20 feet from the
remote control sensor and facing the front of the HOME
THEATER SYSTEM.
Tips on REMOTE CONTROL operation
Remember to point the
REMOTE CONTROL in
the direction of the HOME
THEATER’s sensor, not
the TV set or the DVD
player.
Point the REMOTE CONTROL at the
Home Theater’s Front
Make sure there is a clear path between the REMOTE
CONTROL and the HOME THEATER SYSTEM so that the
signal is not blocked.
6
Gently push here and slide to
open the BATTERY DOOR.
Insert 2 size “AAA” batteries
as shown (included).
•
The REMOTE control’s operating distance may vary
according to the brightness of the room.
•
Do not point bright lights at the REMOTE CONTROL
SENSOR (like laser pointers).
•
Do not place objects between the REMOTE CONTROL unit
and the REMOTE SENSOR.
•
Do not use this REMOTE CONTROL while simultaneously
using the remote control unit of any other equipment, the
signals may mix.
•
Sometimes your TV’s remote may cause an LED to flash,
you can ignore this.
Replace the door.
•
Reversing polarities will damage the batteries and possibly
your REMOTE. Be sure to follow polarity and as indicated.
•
Do not mix different types of batteries together (Alkaline,
Carbon-Zinc, Nickel-Cadmium etc.), or old batteries with new
ones.
•
When not in use for an extended period of time (over 60
days), remove the batteries to prevent possible acid leakage
or corrosion resulting in possible damage to your REMOTE
CONTROL.
•
When the batteries have become discharged, they must be
disposed of in a safe manner that complies with all applicable
laws.
•
Installation of batteries should only be done by an adult
(for safety).
+
Remember, the spring touches the side of each
battery.
Slide door
down.
IB-HT391-WM-E-073003
Choose Your Connection
There are several ways to connect your Home Theater System. Please use the following chart to determine which
connection is the best for you. Turn to the appropriate page and connect your Home Theater System.
COMPONENTS
CABLES
NEEDED
GO TO ...
Cables Needed to Connect Components to Your Home Theater System
The pictures below show the cables needed for the connections represented in this booklet.
NOTE:Audio cables are usually sold as a bundled set, but the connection sketches in this booklet show each cable separately for better
visibility. You will need additional cables to connect everything shown above. Check your other equipments’ booklets to see
what cables are needed.
• Audio (included)
• Video (included)
• Audio (included)
• Video (included)
• Audio (included)
TV
+
HOME THEATER
(only)
Page 15
Page 12
Page 13
Yellow Video cable
(one set included)
CONNECTIONS
7
Speaker Wires (5 sets
are attached to the back
of the speakers)
Red & White Audio cables
(one set included, most installations
will need these)
• Video
(special,
not included)
• Audio
(special,
not included)
AM/FM TUNER
or
other AUX
DEVICE
+
HOME THEATER
Page 16,17
TV/DVD
+
HOME THEATER
TV/VCR
+
HOME THEATER
TV/VCR
+
HOME
THEATER
+
SATELLITE
TV
+
HOME THEATER
+
TV GAME
or
VIDEO CAMERA
• Audio (included)
• Video (included)
• Audio (included)
Page 14
Page
18,19,20
TAPE RECORDER/PLAYER
NOTE:
This only applies if your
TV has audio out jacks.
H
O
M
E
T
H
E
A
T
E
R
S
U
R
R
O
U
N
D
S
O
U
N
D
S
Y
S
T
E
M
PC
1 Set of Audio cables with
green 3.5mm plug for Computer
Connection (or other Source
with 3.5mm Jack)
IB-HT391-WM-E-073003
SPEAKER SYSTEM CONNECTIONS
Speaker System Connections
The speaker wires and connectors are color-coded for easier
set up.
• Connect the Front Left speaker to the Front Left terminals.
• Connect the Front Right speaker to the Front Right terminals.
• Connect the Center speaker to the Center speaker terminals.
• Connect the Rear Left speaker to the Rear Left terminals.
• Connect the Rear Right speaker to the Rear Right terminals.
Connect the supplied speaker system by matching the colors
of the terminals to those of the cords.
IMPORTANT:
Before making connections, make sure the power is off.
8
QUICK SETUP DIAGRAM
NOTE: If you would also like to improve your TV’s sound output with this Home Theater system, your TV set needs to have AUDIO
output jacks. If you have a cable box or satellite receiver, you can connect the receiver’s AUDIO output directly to the AUX
input or any available set of input jacks on the back of this Home Theater system.
IB-HT391-WM-E-073003
SPEAKER SYSTEM CONNECTIONS
To avoid short-circuiting the speakers
•
Make sure the stripped end of each speaker wire does not
touch another speaker terminal or the stripped end of
another speaker wire.
NOTE:
Be sure to match the speaker wire to the appropriate terminal on
the back of the main set: (+) to (+) (color), and (-) to (-) (black). If the
wires are reversed, the sound will be distorted and will lack some
tones. Follow the color codes of each terminals.
•
Stripped wires are touching each other due to excessive
removal of insulation. Do not allow the above to happen on
your set.
Tips for connecting the speaker wires
Unwind and stretch out the speaker wires attached with each
speakers, then push and hold down the speaker terminal tab on
the back of the main set to insert each wire. Make sure the wire is
fully inserted, but the insulation is not covering the inserted part of
the speaker wires.
9
•
Stripped speaker wire is touching another speaker terminal.
Make sure not even 1 strand of wire touches the other
wire!
Examples of poor connection of the
speaker wires
SPEAKER TERMINALS
GO ON TO THE NEXT WIRE & REPEAT ABOVE.
MAKE SURE POWER IS OFF WHEN DOING THE ABOVE.
NOTE: If longer wires are needed, you may buy any good quality
speaker wire and splice the wires yourself. Please make sure
the wires are not shorting to each other and observe the correct
color polarity.Many speaker wires have a dotted line or solid line
or raised rib on one side to identify each side.
Also make sure you use electrical tape to cover your splices.
PUSH AND HOLD THE COLORED TAB OF TERMINAL.
WHILE HOLDING THE TAB OF THE TERMINAL, STICK
THE EXPOSED PART OF THE WIRE INTO THE HOLE
OF THE TERMINAL.
REMOVE YOUR FINGER FROM THE TERMINAL TO
LOCK THE WIRE INSIDE THE TERMINAL.
IB-HT391-WM-E-073003
10
Your system is supplied with 5 compact sized satellite speakers and
one large subwoofer (main set). The satellite speakers and the center
speaker reproduce only the mid range and higher frequencies. All of
the low frequency (bass) sounds are produced by the subwoofer. Proper
positioning and placement of the speakers is important in order to provide
the best surround sound experience. We understand that due to the
size and shape of your listening room, and the location of your furniture,
you may not be able to set up the speakers exactly as per these
diagrams. However these simple guidelines will help you maximize
your home theater experience.
• Note the speaker levels are preset at the factory and most people will
not need to fine tune the sound of each speaker. We suggest you skip
this part at first. Later on you can adjust the sound level of each
individual speaker. See Page 22.
• Although all 5 satellites are of the same size, the speakers inside the
cabinets are different. The speaker wires on the back of the cabinets
are color-coded, as are the speaker terminals on the back of the main
unit. Refer to the connection diagram on page 8. Be sure you are
using the correct satellite speaker in each location, front, rear and
center. Please follow the colors for best results.
• For best surround sound effects, all 4 of the satellite speakers and the
center speaker should be roughly at the same distance from your
usual listening position.
SPEAKER POSITIONING INFORMATION
POSITION ALL 5 SPEAKERS APPROXIMATELY AT THE
SAME DISTANCE FROM YOUR LISTENING POSITION.
POSITION THE SUBWOOFER AS BELOW.
• The 4 satellite speakers and the center speaker should be placed approximately the same distance from your listening
position.
• The center speaker should be placed directly above (or below) the TV set. Left and right front speakers should be
approximately at the same height as the center speaker.
• The rear speakers should be either in line with, or behind your listening position, approximately at ear level, or slightly
above.
• The subwoofer (main set) should be on the floor near the TV, or in any corner, but remember you need a clear path to
your remote (don’t block this set with a curtain).
• All speakers must be visible. Do not hide them behind curtains, furniture, etc, as this will affect the sound.
Your Usual Seat
POSITION THE SPEAKERS LIKE THIS FOR OPTIMAL LISTENING EXPERIENCE
IB-HT391-WM-E-073003
SPEAKER POSITIONING INFORMATION
• The left front, right front, and center speakers should be
placed at roughly the same height. The center speaker
reproduces most of the dialog spoken by the actors on the
TV screen, therefore it should be placed either directly above
or below the center of the TV set. Once you position the
center speaker, try to position the left front and right front
speakers at the same height. It is not recommended to place
any of the satellite speakers on the floor. Many people prefer
to place the center speaker horizontally above the TV set.
• The left rear and right rear speakers can be placed in line
with your listening position or behind your listening position.
Ideally they should be placed slightly above your ear level
when you are seated in your normal listening position.
• We have provided one keyhole opening on the backs of all
the satellite speakers that allow the satellite speakers to be
wall mounted in a vertical position.
• The subwoofer will provide the most dramatic bass effects
(low frequency sounds like explosions and thunder) when it
is placed on the floor. Do not place the subwoofer on a
stand or table. The subwoofer should be placed in the front
of the room so that it is facing towards your listening position.
It can be placed on either side of the TV or even in the
corner of the room, as far away as the cable will allow. The
bass sounds from the subwoofer are non-directional. You
will not really be able to tell where the bass is coming from.
SATELLITE SPEAKERS
SUBWOOFER
11
• LONG ROOMS - In case your room is unusually long and
longer wire are needed, you may buy any good quality
speaker wire and splice the wires yourself for adding wire
length to your speakers. Be careful not to allow the plus +
and minus - wires to touch each other. Many speaker wires
have a dotted line or solid line or raised rib on one side to
identify each side.
Remember to cover the splices with electrical tape.
IB-HT391-WM-E-073003
12
1.Connect the 5 satellite speakers as shown on Page 8 (or the QUICK SETUP DIAGRAM packed with the set).
2.Insert the stereo audio cables (included) into the AUX AUDIO INPUT L (left=white) and R (right=red) jacks or any
available set of input jacks on the back of your HOME THEATER SYSTEM, and into the corresponding AUDIO OUT
jacks on your TV, this will allow your TV’s sound to play through your HOME THEATER SYSTEM.
NOTE: On some TVs, you may have to activate the audio out jacks of your TV. See your TV’s booklet.
3.Insert the AC power cord into an AC outlet.
4.Make sure the POWER switch on the back of the main unit is at “ON” position. Next press the ON/STANDBY button
on the front of the main set or on the REMOTE to turn the set on (or off).
5.Press the INPUT SOURCE button several times till the AUX indicator lights.
NOTE:The factory’s default input source is DVD with 5.1 channel sound output. When the set is turned to
ON, the DVD indicator and 5.1 channel indicator will be on and sound will come out of 5 speakers plus
the subwoofer. To change 5.1 channel to 2 channel output, press the SPEAKER CHANNELS button. The sound
will come out of only 2 front speakers plus the subwoofer.
6.Go to Page 21 for other detailed instructions.
NOTE:Your cable or antenna connection to your TV are not touched with this connection. Leave your antenna cable
to your TV as you normally would. No changes will be made to your current antenna connections.
TV CONNECTIONS
Home Theater System + TV (if your TV has Audio Output jacks)
(If you don’t have a DVD player yet)
CONNECT ALL SPEAKERS AS SHOWN ON PAGE 8 (OR THE QUICK SETUP DIAGRAM SHEET)
NOTE: On some TVs, these jacks are in the front,
or your TV may not have these jacks.
If you have a cable box or satellite receiver, you
can connect the receiver AUDIO OUTPUT directly
to your AUX INPUT or any available set of input
jacks on the back of the HOME THEATER
SYSTEM.
NOTE:If your TV does not have audio output jacks,
your TV’s sound cannot be heard through
the surround sound system. But, you can
still use it for your DVD player etc.
IB-HT391-WM-E-073003
Home Theater System + TV + DVD Player
1.Insert the audio cables (included) into the DVD INPUT jacks L (Left = White) and R (Right = Red) on the back of
your HOME THEATER SYSTEM, and into the corresponding AUDIO OUT jacks on your DVD player, this will allow
your DVD’s sound to play through your HOME THEATER SYSTEM.
2.Insert the video cable directly into the VIDEO OUT jack on the back of your DVD player and into the VIDEO IN jack
on the back of your TV set. This is especially convenient if your TV has several inputs.
NOTE: You may insert the video cable directly into the VIDEO OUT jack on the back of your DVD and into the
VIDEO IN jack on the back of your HOME THEATER SYSTEM. Then insert the video cable into the VIDEO
IN jack on your TV, and into the VIDEO OUT jack on the back of your HOME THEATER SYSTEM.
3.Insert the AC power cord into an AC outlet.
4.Make sure the POWER switch on the back of the main unit is at “ON” position. Next press the ON/STANDBY button
on the front of the main set or on the REMOTE to turn the set on (or off).
NOTE:The factory’s default input source is DVD with 5.1 channel sound output. When the set is turned to ON, the
DVD indicator and 5.1 channel indicator will be on and sound will come out of 5 speakers plus the
subwoofer. To change 5.1 channel to 2 channel output, press the SPEAKER CHANNELS button. The sound
will come out of only 2 front speakers plus the subwoofer.
5.Make sure your DVD player is on and follow your DVD player’s instructions.
NOTE:For some DVDs, if the sound output is not set to analog, the audio cables may not be active and there will be no
sound output. If this happens, check and make sure your DVD’s sound output is set to analog.
6.Go to Page 21 for other detailed instructions.
NOTE:Your cable or antenna connection to your TV are not affected with this connection. Leave your antenna cable
connected to your TV as you normally would. No changes will be made to your current antenna connections.
NOTE: Some newer TV sets have several VIDEO
INPUT jacks. You may use one of these for your
DVD player andthe others for connecting to the
VIDEO OUT jacks of the component. If your set is
older and only has a single VIDEO INPUT jack,
you may buy a switch box to change the video from
DVD to Game.
TV + DVD CONNECTIONS
13
CONNECT ALL SPEAKERS AS SHOWN ON PAGE 8
(OR THE QUICK SETUP DIAGRAM SHEET)
Or connect it into the VIDEO IN
jack of the main set first, then
use another Video cable to
connect the VIDEO OUT jack
to the VIDEO IN jack of your
TV.
1.Insert the stereo audio cables (included) into the AUX INPUT L (left=white) and R (right=red) jacks or any available
set of input jacks on the back of your HOME THEATER SYSTEM, and into the corresponding AUDIO OUT jacks on
your VCR, this will allow your VCR’s sound to play through your HOME THEATER SYSTEM.
2.Connections of your cables are not changed when you add your HOME THEATER SYSTEM.
NOTE: You will hear sound from both the TV and your HOME THEATER SYSTEM, this is normal.
3.Insert the AC power cord into an AC outlet.
4.Make sure the POWER switch on the back of the main unit is at “ON” position. Next press the ON/STANDBY button
on the front of the main set or on the REMOTE to turn the set on (or off).
NOTE:The factory’s default input source is DVD with 5.1 channel sound output. When the set is turned to ON, the
DVD indicator and 5.1 channel indicator will be on and sound will come out of 5 speakers plus the subwoofer.
To change 5.1 channel to 2 channel output, press the SPEAKER CHANNELS button. The sound will come out of
only 2 front speakers plus the subwoofer.
5.Press the INPUT SOURCE button several times till the AUX indicator lights.
6.Make sure your VCR is on and follow your VCR’s instructions.
7.Go to Page 21 for other detailed instructions.
TV + VCR CONNECTIONS
14
Home Theater System + TV + VCR
CONNECT ALL SPEAKERS AS SHOWN ON PAGE 8 (OR THE QUICK SETUP DIAGRAM SHEET)
This does not change
from your current connection.
CABLE OR
ON AIR ANTENNA/
SATELLITE SIGNAL
15
Home Theater System + TV + VCR + Satellite
TV + VCR + SATELLITE RECEIVER CONNECTIONS
1.Follow the same on P14 to connect your VCR with your HOME THEATER SYSTEM.
2.To hear the sound of the satellite programs through your HOME THEATER SYSTEM, just insert a set of audio cables
(optional, not included) into one pair of the 3 audio input jacks of your HOME THEATER SYSTEM, and into the
corresponding AUDIO OUT jacks of your SATELLITE RECEIVER/CABLE BOX.
3.Your RF (coaxial) cable connection from your SATELLITE RECEIVER/CABLE BOX to your VCR is unchanged, the
same as before.
NOTE: You will hear sound from both the TV and your HOME THEATER SYSTEM, this is normal.
4.Insert the AC power cord into an AC outlet.
5.Make sure the POWER switch on the back of the main unit is at “ON” position. Next press the ON/STANDBY button on
the front of the main set or on the REMOTE to turn the set on (or off).
NOTE:The factory’s default input source is DVD with 5.1 channel sound output. When the set is turned to
ON, the DVD indicator and 5.1 channel indicator will be on and sound will come out of 5 speakers plus
the subwoofer. To change 5.1 channel to 2 channel output, press the SPEAKER CHANNELS button. The sound
will come out of only 2 front speakers plus the subwoofer.
6.Press the INPUT SOURCE button several times till the AUX indicator lights.
7.Make sure your VCR is on and follow your VCR’s instructions.
8.Go to Page 21 for other detailed instructions.
CONNECT ALL SPEAKERS AS SHOWN ON PAGE 8 (OR THE QUICK SETUP DIAGRAM SHEET).
SATELLITE RECEIVER/CABLE BOX
CABLE OR
ON AIR ANTENNA/
SATELLITE SIGNAL
RF (coaxial) cable
unchanged, same as
before.
IB-HT391-WM-E-073003
TV + TV GAME CONNECTIONS
Home Theater System + TV + TV Game
16
NOTE: Your TV GAME may
have a special cable for
connections. This diagram
is only for illustration.
1.Insert the stereo audio cables into the GAME INPUT AUDIO L (left=white) and AUDIO R (right=red) jacks or any
available set of input jacks on the BACK of your HOME THEATER SYSTEM, and into the corresponding AUDIO OUT
jacks on your TV GAME, this will allow your TV GAME’s sound to play through your HOME THEATER SYSTEM.
2.Insert the yellow video cable (included with your TV GAME) into the GAME INPUT VIDEO jack on the BACK of your
HOME THEATER SYSTEM, and into the VIDEO OUT jack on your TV GAME.
3.Insert another video cable into the VIDEO OUT jack on the back of your HOME THEATER SYSTEM, and into the VIDEO IN
jack on your TV.
4.Insert the AC power cord into an AC outlet.
5.Make sure the POWER switch on the back of the main unit is at “ON” position. Next press the ON/STANDBY button on
the front of the main set or on the REMOTE to turn the set on (or off).
NOTE:The factory’s default input source is DVD with 5.1 channel sound output. When the set is turned to ON, the
DVD indicator and 5.1 channel indicator will be on and sound will come out of 5 speakers plus the subwoofer.
To change 5.1 channel to 2 channel output, press the SPEAKER CHANNELS button. The sound will come out of only
2 front speakers plus the subwoofer.
6.Press the INPUT SOURCE button several times till the GAME indicator lights.
7.Make sure your TV GAME is on and follow your TV GAME’s instructions.
8.Go to Page 21 for other detailed instructions.
NOTE: If your TV set has several VIDEO INPUT
jacks, you may connect your GAME’s VIDEO cable
to one of your TV’s VIDEO INPUT jacks directly.
CONNECT ALL SPEAKERS AS SHOWN ON PAGE 8 (OR THE QUICK SETUP DIAGRAM SHEET).
AUDIO / VIDEO CABLE
(not included)
IB-HT391-WM-E-073003
1.Insert the stereo audio cables into the GAME INPUT AUDIO L (left=white) and AUDIO R (right=red) jacks or any
available set of input jacks on the BACK of your HOME THEATER SYSTEM, and into the corresponding AUDIO OUT
jacks on your VIDEO CAMERA, this will allow your CAMERA VIDEO’s sound to play through your HOME THEATER
SYSTEM. (NOTE: Many video cameras have special plugs on one side to connect to your camera.)
2.Insert the video cable (included with your VIDEO CAMERA) into the GAME INPUT VIDEO IN jack on the BACK of your
HOMETHEATER SYSTEM, and into the VIDEO OUT jack on your VIDEO CAMERA. (NOTE: Your video camera may
have a 3.5mm triple jack, consult your camera’s booklet for details.)
3.Insert the video cable (included) into the VIDEO OUT jack on the back of your HOME THEATER SYSTEM, and into the
VIDEO IN jack on your TV.
4.Insert the AC power cord into an AC outlet.
5.Make sure the POWER switch on the back of the main unit is at “ON” position. Next press the ON/STANDBY button on
the front of the main set or on the REMOTE to turn the set on (or off).
6.Press the INPUT SOURCE button several times till the GAME indicator lights. (This setting is either for a Video
Camera or a TV Game.)
NOTE:The factory’s default input source is DVD with 5.1 channel sound output. When the set is turned to ON, the
DVD indicator and 5.1 channel indicator will be on and sound will come out of 5 speakers plus the subwoofer.
To change 5.1 channel to 2 channel output, press the SPEAKER CHANNELS button. The sound will come out of
only 2 front speakers plus the subwoofer.
7.Make sure your VIDEO CAMERA is on and follow your VIDEO CAMERA’s instructions.
8.Go to Page 21 for other detailed instructions.
TV + VIDEO CAMERA CONNECTIONS
17
Home Theater System + TV + Video Camera
NOTE: Your VIDEO CAMERA
may have a special cable (with
a triple 3.5mm plug on one side)
for connections. This diagram is
only for illustrations.
CONNECT ALL SPEAKERS AS SHOWN ON PAGE 8 (OR THE QUICK SETUP DIAGRAM SHEET).
NOTE: If your TV set has several VIDEO
INPUT jacks, you may connect your VIDEO
CAMERA cable to one of your TV’s VIDEO
INPUT jacks directly.
AUDIO / VIDEO CABLE
(not included)
IB-HT391-WM-E-073003
AUX IN CONNECTIONS
1.Insert the audio cables into the AUDIO OUTPUT L (left=white) and R (right=red) jacks of your TAPE RECORDER
PLAYER, and into the corresponding AUX INPUT jacks or any available set of input jacks on your HOME
THEATER. This will enable you to hear your components system through your HOME THEATER SYSTEM.
2.You may also use the green 3.5mm plug and cable (included) to connect your CD PLAYER, RADIO or other
device to your HOME THEATER SYSTEM
3.Make sure the POWERswitch on the back of the main unit is at “ON” position. Next press the ON/STANDBY
button on the front of the main set or on the REMOTE to turn the set on (or off).
4.Press the INPUT SOURCE button several times till the AUX indicator lights.
NOTE:The factory’s default input source is DVD with 5.1 channel sound output. When the set is turned to
ON, the DVD indicator and 5.1 channel indicator will be on and sound will come out of 5 speakers plus
the subwoofer. To change 5.1 channel to 2 channel output, press the SPEAKER CHANNELS button. The
sound will come out of only 2 front speakers plus the subwoofer.
5.Make sure your AUX IN component is on and follow your component’s instructions.
6.Go to Page 21 for other detailed instructions.
18
•
Illustration is showing some possible connections. You can only connect ONE of these components
to the AUX INPUT jacks of your HOME THEATER SYSTEM (AUX stands for Auxiliary).
•
You can hear the sound of any one of these devices through your HOME THEATER SYSTEM if you
connect the proper cables.
CONNECT ALL SPEAKERS AS SHOWN ON PAGE 8 (OR THE QUICK SETUP DIAGRAM SHEET).
3.5MM PLUG
IB-HT391-WM-E-073003
AM / FM TUNER CONNECTIONS
1.Insert the audio cables into the AUDIO OUTPUT L (left=white) and R (right=red) jacks on the back of your
AM/FM TUNER, and into the corresponding AUX INPUT jacks or any available set of input jacks on the back of
your HOME THEATER. This will enable you to hear your stereo AM/FM TUNER through your HOME THEATER
SYSTEM.
2.Make sure the POWERswitch on the back of the main unit is at “ON” position. Next press the ON/STANDBY
button on the front of the main set or on the REMOTE to turn the set on (or off).
3.Press the INPUT SOURCE button several times till the AUX indicator lights.
NOTE:The factory’s default input source is DVD with 5.1 channel sound output. When the set is turned to
ON, the DVD indicator and 5.1 channel indicator will be on and sound will come out of 5 speakers plus
the subwoofer. To change 5.1 channel to 2 channel output, press the SPEAKER CHANNELS button. The
sound will come out of only 2 front speakers plus the subwoofer.
4.Make sure your AM/FM TUNER is on and follow your AM/FM TUNER’s instructions.
5.Go to Page 21 for other detailed instructions.
19
CONNECT ALL SPEAKERS AS SHOWN ON PAGE 8 (OR THE QUICK SETUP DIAGRAM SHEET).
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26

Lenoxx HT-391 Kasutusjuhend

Lenoxx
Bränd
Lenoxx
Mudel
HT-391
Kategooria
Kõlarikomplektid
Tüüp
Kasutusjuhend
Laadige alla PDF
aruanne

teistes keeltes

Muud dokumendid