Hilti PR 30 Kasutusjuhend

PR 30-HVS A12

English 1

Български 20

Română 40

Türkçe 60

ﻋﺮﺑﻲ 79

Latviešu 99

Lietuvių 119

Eesti 138

Українська 156

Қазақ 177

日本語 197

한국어 215

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

1

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

2

3

4

5

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

6

7

8

9

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

10

11

12

13

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

14

15

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

*2134494*

2134494 English 1

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free

handling and use of the product.

• Observe the safety instructions and warnings in this documentation and on the product.

• Always keep the operating instructions with the product and make sure that the operating instructions

are with the product when it is given to other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶ Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶ Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶

Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage

to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the beginning of these operating

instructions

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text

Item reference numbers are used in the overview illustrations and refer to the numbers used in

the product overview section

This symbol is intended to draw special attention to certain points when handling the product.

Wireless data transfer

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

2 English 2134494

*2134494*

1.3 On the product

Laser information

Laser class 2 based on standard IEC60825-1 / EN60825-1:2007 and compliant with CFR

21 § 1040 (Laser Notice 50).

Do not look straight into the laser beam.

1.4 Product information

products are designed for professional users and only trained, authorized personnel are permitted

to operate, service and maintain the products. This personnel must be specifically informed about the

possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶ Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Rotating laser PR 30-HVS A12 | PRA 30

Generation 02

Serial no.

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany

1.6 Type approval test

The notified tester, CSA Group Bayern, number 1948, has tested the devices and evaluated the documents

and issued the following type approval certifications:

• PR 30HVS A12: ZS 17 10 50140 006

• PRA 30: ZS 17 10 50140 005

2 Safety

2.1 Basic information concerning safety

Read all safety instructions and other instructions. Failure to observe the safety instructions and other

instructions may result in electric shock, fire and/or serious injury.

Retain all safety precautions and instructions for future reference. The term “electric tool” used in the

safety instructions refers to your mains-operated (corded) electric tool or battery-operated (cordless) electric

tool.

2.2 General safety measures

▶ Stay alert, watch what you are doing and use common sense when operating a power tool. Do not

use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of

inattention while operating the power tool can result in serious personal injury.

▶ Do not render safety devices ineffective and do not remove information and warning notices.

▶ Keep children well away from laser devices.

▶ Laser radiation in excess of Class 2 may be emitted if the device is opened without following the correct

procedures. Have the device repaired only by Hilti Service.

▶ Project laser beams well above or well below eye height.

▶ Take the influences of the surrounding area into account. Do not use the device where there is a

risk of fire or explosion.

▶ Statement in accordance with FCC §15.21: Changes or modifications not expressly approved by Hilti

can restrict the user’s authorization to operate the equipment.

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

*2134494*

2134494 English 3

▶ You must check the accuracy of the device after it has been dropped or subjected to other

mechanical stresses.

▶ When the device is brought into a warm environment from very cold conditions, or vice-versa,

allow it to become acclimatized before use.

▶ When using adapters or accessories, make sure that the equipment is securely mounted.

▶ Keep the laser aperture clean to avoid measurement errors.

▶ The device is designed for the tough conditions of jobsite use, but as with other optical and

electronic instruments (e.g. binoculars, spectacles, cameras) it must be handled with care.

▶ The device is protected to prevent the ingress of moisture, but you must always wipe it dry before

stowing it in the transport container.

▶ Check the device before using it for important measuring work.

▶ Repeatedly check accuracy while using the device.

▶ Make sure that the workplace is well lit.

▶ Do not expose the laser to rain or wet conditions.

▶ Do not touch the contacts.

▶ Maintain the device carefully. Check that moving parts are in full working order and do not jam

and make sure there are no parts that are broken or damaged in such a way as to impair operation

of the device. If it damaged, have the device repaired before use. Many accidents are caused by

poorly maintained equipment.

2.3 Proper preparation of the working area

▶ Secure the area in which you will be taking measurements. Make sure that the laser beam is not

directed toward other persons or toward yourself while setting up the laser tool.

▶ Avoid unfavorable body positions when working from ladders. Make sure you work from a safe

stance and stay in balance at all times.

▶ Readings taken in the vicinity of reflective objects or surfaces, through panes of glass or similar materials

may produce incorrect results.

▶ Ensure that the tool is set up on a stable, level surface (not subject to vibration).

▶ Use the tool only within its specified limits.

▶ Use the tool and its accessories etc. in accordance with these instructions and in the manner

intended for the particular type of tool. Take the working conditions and the work to be performed

into account. Use of tools for applications different from those intended could result in a hazardous

situation.

▶ Use of the telescopic staff in the vicinity of overhead high voltage cables is not permissible.

2.4 Electromagnetic compatibility

Although the tool complies with the strict requirements of the applicable directives, Hilti cannot exclude the

following possibilities:

• The tool may be negatively affected by powerful electromagnetic radiation, possibly leading to incorrect

operation.

In these cases, or if you are otherwise unsure, confirmatory measurements should be made by other

means.

• The tool can cause interference to other devices (e.g. aircraft navigation equipment).

2.5 Laser classification for Class 2 laser products

The tool complies with laser Class 2 as per IEC60825-1:2007 / EN60825-1:2007. This tool may be used

without need for further protective measures.

CAUTION

Risk of injury! Do not direct the laser beam toward persons.

▶ Never look directly into the source of the laser beam. In the event of direct eye contact, close your eyes

and move your head out of the path of the laser beam.

2.6 Careful use of battery-powered tools

▶ Do not expose batteries to high temperatures, the direct heat of the sun, and keep them away

from fire. There is a risk of explosion.

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

4 English 2134494

*2134494*

▶ Do not disassemble, squash or incinerate batteries and do not subject them to temperatures over

80°C (176°F). This presents a risk of fire, explosion or injury through contact with caustic substances.

▶ Do not subject the battery to hard mechanical impacts and do not throw the battery.

▶ Batteries must be kept out of reach of children.

▶ Avoid ingress of moisture. Ingress of moisture may cause a short circuit, resulting in burning injuries or

fire.

▶ Under abusive conditions, liquid may leak from the battery. Avoid contact with the liquid. If contact

accidentally occurs, flush with water. If the liquid contacts the eyes, also seek medical attention.

Liquid leaking from the battery may cause irritation or burns.

▶ Use only batteries of the type approved for use with the applicable tool. Use of other batteries or

use of the batteries for purposes for which they are not intended presents a risk of fire and explosion.

▶ Store the battery in a cool and dry place. Never store the battery where it is exposed to direct sunlight or

sources of heat, e.g. on heaters / radiators or behind glass.

▶ When not in use, keep the battery and the charger away from paper clips, coins, keys, nails,

screws or other small metal objects that could cause a short circuit at the battery terminals or the

charging contacts. Short-circuiting the contacts on a battery or charger may cause burning injuries or

start a fire.

▶ Do not charge or continue to use damaged batteries (e.g. batteries with cracks, broken parts, bent

or pushed-in and/or pulled-out contacts).

▶ Recharge only with the charger specified by the manufacturer. A charger that is suitable for a certain

type of battery may present a risk of fire when used with other types of battery.

▶ Observe the special guidelines applicable to the transport, storage and use of Li-ion batteries.

▶ The battery must be insulated or removed from the tool before the tool is shipped or sent by mail.

Leaking batteries may damage the tool.

▶ If the battery gets noticeably hot when not in use, this may indicate that the battery or the tool / battery

system is faulty. In this case, place the tool in a non-flammable location, well away from flammable

materials, where it can be kept under observation and allowed to cool down.

3 Description

3.1 Product overview

3.1.1 PR 30-HVS rotating laser 1

@

Laser beam (plane of rotation)

;

Rotary head

=

Sight

%

Grip

&

Battery release button

(

Liion battery

)

Battery state-of-charge display

+

Control panel

§

Base plate with 5/8" thread

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

*2134494*

2134494 English 5

3.1.2 PR 30-HVS control panel 2

@

Inclined plane mode button and LED

;

Shock warning function button and LED

=

LED arrow for electronic inclination align-

ment

%

Electronic inclination alignment button (only

in combination with inclined plane mode)

&

Auto-leveling LED

(

On/off button

)

Surveillance mode LED (only with auto-

matic vertical alignment)

+

Battery charge status LED

3.1.3 PRA 30 laser receiver and control panel 3

@

Volume button

;

Negative inclination to the left or downward

with PRA 90

=

Automatic alignment / surveillance mode in

the vertical plane (double-click)

%

Units key

&

Positive inclination to the right or upward

with PRA 90

(

On/off button

)

Display

+

Marking notch

§

Detection area

3.1.4 PRA 30 laser receiver display 4

@

Indicator showing distance from laser plane

;

Volume indicator

=

Units key

%

Detection area

&

Marking notch

3.1.5 Intended use

The product described is a rotating laser with a visible rotating laser beam. It can be operated by one

person. The tool is designed to be used to determine, transfer and check levels, verticals, slopes and right

angles. Examples of its uses are: transferring datum lines and height marks, determining right angles for

walls, vertical alignment on reference points and setting out slopes.

▶ Use only the Hilti B 12⁄2.6 Li-Ion battery for this product.

▶ Use only the Hilti C 4⁄1250 charger for this product.

3.1.6 Features

The rotating laser can be used vertically, horizontally and for inclined planes.

The tool is equipped with the following operating status indicators: auto-leveling LED, inclined plane mode

LED, surveillance mode LED and shock warning LED.

Auto-leveling

Auto-leveling takes place after the tool is switched on. LEDs indicate the current operating status. Auto-

leveling is active within the ±5° range relative to the horizontal plane and can be deactivated by pressing the

button. The tool can be set up directly on the ground or floor, on a tripod, or with the aid of suitable

mounting brackets.

Automatic alignment

Automatic alignment allows a single person to bring the laser plane into alignment with the laser receiver.

The rotating laser tool detects the applicable direction of alignment as follows:

• Horizontal in conjunction with the PRA 90 automatic tripod and PRA 30 laser receiver.

• Inclination in conjunction with the PRA 30 laser receiver, and (optional) with the PRA 79 slope adapter.

• Vertical in conjunction with the PRA 30 laser receiver.

Inclination angle

The inclination can be set by the following means:

• Manual entry of the values at the PRA 30 laser receiver

• Automatic alignment of the rotating laser with the PRA 30 laser receiver

• Presetting an inclination through use of the PRA 79 slope adapter

The angle of inclination can be read from the laser receiver.

Surveillance when working in the vertical plane

The rotating laser monitors alignment of the laser plane in combination with the PRA 30 laser receiver. In

the event of deviations in alignment, laser rotation stops for 40 seconds. During this time the tool corrects

all errors caused by temperature fluctuations, wind or other influences. Laser rotation restarts after this

automatic correction. If necessary, the surveillance function can be deactivated.

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

6 English 2134494

*2134494*

Automatic switch-off

The tool switches off automatically if it is unable to level itself because the laser:

• Is inclined at more than 5° relative to the horizontal plane (except in inclined plane mode).

• Is blocked mechanically.

• Has been knocked off level by an impact or vibration.

When the tool has switched itself off, rotation stops and all LEDs flash.

Shock warning function

If the laser is knocked off level during operation, the built-in shock warning function switches the tool to

warning mode. The shock warning function does not go active until two minutes after completion of auto-

leveling. If a button on the control panel is pressed within this two-minute period it will take a further two

minutes for the shock warning function to go active. If the laser is in warning mode:

• All LEDs flash.

• The laser stops rotating.

• The laser beam switches off.

The shock warning function can be switched off by pressing the button if the ground or floor is not free

from vibration or when you are working in inclined plane mode.

▶ Deactivate the shock warning function. → page 12

Laser receiver / remote control unit

Hilti laser receivers digitally indicate the distance between the marking notch on the laser receiver and the

position at which the laser beam (laser plane) strikes the detection area on the receiver. The laser beam can

also be received over long distances. The PRA 30 can be used as a laser receiver and also as a remote

control unit for the rotating laser. The system of units and the unit of measurement can be set as desired.

▶ Set the units that are to be used. → page 14

▶ Change the units used by the laser receiver. → page 14

Pairing accessories and device

Pairing is the act of enabling accessories and devices to communicate with each other by wireless.

The rotating laser and the laser receiver are already paired when supplied. This helps ensure trouble-free

operation within the vicinity of other wireless devices.

Additional laser receivers or PRA 90 automatic tripods cannot be used without first being paired.

▶ Pair the rotating laser and the laser receiver. → page 13

▶ Pair the tripod and laser receiver. → page 13

3.1.7 LED indicators

The rotating laser is equipped with an LED display.

Status Meaning

All LEDs blink. • The tool has been bumped, knocked off level or

is subject to some other error.

The auto-leveling LED blinks green. • The tool is in the leveling phase.

The auto-leveling LED lights green constantly. • The tool has leveled itself / is operating normally.

The shock warning LED lights orange constantly. • Shock warning mode is deactivated.

The inclination LED blinks orange. • Alignment in the sloping plane.

The inclination LED lights orange constantly • Inclined plane mode is active.

The surveillance LED blinks orange. • The tool is aligning the laser plane with the

reference point (PRA 30).

The surveillance mode LED lights orange con-

stantly.

• The tool is in surveillance mode. Alignment with

the reference point (PRA 30) is correct.

The LED arrows blink orange. • The tool is in electronic inclination alignment

mode, the PRA 30 is receiving no laser beam.

The LED arrows light orange constantly. • The tool is correctly aligned with the PRA 30.

The left LED arrow lights orange. • Rotate the tool clockwise.

The right LED arrow lights orange. • Rotate the tool counterclockwise.

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

*2134494*

2134494 English 7

3.1.8 Li-ion battery charge state display

The Li-ion battery features a state of charge display.

Status Meaning

4 LEDs light. • Charge status: 75 % to 100 %

3 LEDs light. • Charge status: 50 % to 75 %

2 LEDs light. • Charge status: 25 % to 50 %

1 LED lights. • Charge status: 10 % to 25 %

1 LED blinks. • Charge status: < 10 %

When the tool is in operation, the battery charge status is indicated in the display on the tool.

When not in operation, battery charge state can be indicated by lightly pressing the release button.

During charging, charge state is indicated by the LEDs on the battery (please refer to the operating

instructions for the charger).

3.1.9 Items supplied

PR 30-HVS A12 rotating laser, PRA 30 (03) laser receiver / remote control unit, 2 batteries (AA cells), PRA 83

laser receiver holder, operating instructions.

Other system products approved for use with this product can be found at your local Hilti Store or at:

www.hilti.group | USA: www.hilti.com

4 Technical data

4.1 Technical data, rotating laser

PR 30-HVS A12

Receiving range (diameter) PRA 30 (03)

2 m … 500 m

Communication range (PRA 30)

150 m

Accuracy at 10 m (under standard ambient conditions in accor-

dance with MILSTD810G)

±0.5 mm

Laser class

Visible, Laser Class 2,

620-690 nm/Po<4.85 mW ≥

300 ⁄min; EN 60825-1:2007;

IEC 60825-1:2007

Self-leveling range

±5°

Operating temperature

−20 ℃ … 50 ℃

Storage temperature

−25 ℃ … 60 ℃

Weight (including battery)

2.5 kg

Drop test height (under standard ambient conditions in accor-

dance with MILSTD810G)

1.5 m

Protection class in accordance with IEC 60529 (except battery

and battery compartment)

IP66

Plumb beam

Constant beam, perpendicular

to the plane of rotation

Maximum emitted transmission power

7.8 dBm

Frequency

2,400 MHz … 2,483.5 MHz

4.2 Technical data, laser receiver

Indicator range, distance from zero

±52 mm

Laser plane display range

±0.5 mm

Length of the detection area

≤ 120 mm

Center indication from top edge of casing

75 mm

Time without detection before automatic power off

15 min

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

8 English 2134494

*2134494*

Range of remote control unit (diameter) for the PR 30-HVS

2 m … 150 m

Drop test height in the PRA 30 laser receiver holder (under stan-

dard ambient conditions in accordance with MILSTD810G)

2 m

Operating temperature

−20 ℃ … 50 ℃

Storage temperature

−25 ℃ … 60 ℃

Weight (including batteries)

0.25 kg

Protection class in accordance with IEC 60529 (except battery

compartment)

IP66

Maximum emitted transmission power

−0.2 dBm

Frequency

2,400 MHz … 2,483.5 MHz

5 Operating the rotating laser

5.1 Preparations at the workplace

CAUTION

Risk of injury by inadvertent starting!

▶ Before inserting the battery, make sure that the product is switched off.

▶ Remove the battery before making any adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

5.2 Handling the laser and battery correctly 5

The B12 battery has no protection class. Do not expose the battery to rain or wet conditions.

In accordance with the Hilti instructions, the battery may be used only with the associated product

and must be inserted in the battery compartment for this purpose.

1. Fig. 1: Working in horizontal mode.

2. Fig. 2: In inclined plane mode, the laser should be lifted at the control panel side.

3. Fig. 3: Laying down or transporting in an inclined position. Working in the vertical plane.

◁ Hold the laser so that the battery compartment does NOT face upwards, so that no moisture can

enter.

5.3 Inserting / removing the battery 6

CAUTION

Electrical hazard. Dirty contacts may cause a short circuit.

▶ Check that the contacts on the battery and on the tool are free from foreign objects before inserting the

battery.

CAUTION

Risk of injury. If the battery is not fitted correctly it may drop out and fall.

▶ Check that the battery is securely seated in the tool so that it cannot drop out and fall, thereby presenting

a hazard to other persons.

1. Push the battery in until it engages securely.

◁ The laser is ready to switch on.

2. Press the release button and hold it in this position.

3. Pull the battery out.

5.4 Switching the laser on and working in the horizontal plane 7

Check the accuracy of the laser tool before using it for important measuring tasks, especially if it has

been dropped or subjected to unusual influences or impacts etc.

1. Mount the laser on a suitable holder or bracket.

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

*2134494*

2134494 English 9

2.

Press the button.

◁

The auto-leveling LED flashes green.

◁ As soon as the tool has leveled itself, the laser beam switches on and begins to rotate and the "auto

leveling" LED shows steadily.

A wall bracket or tripod may be used as mounting devices. The angle of inclination of the surface

on which it stands should not exceed ± 5°.

5.5 Manual horizontal alignment 8

The rotating laser is mounted on the PRA 90 automatic tripod.

The PRA 30 laser receiver, the rotating laser and the PRA 90 automatic tripod are paired.

The PRA 30 laser receiver and the control panel of the PRA 90 automatic tripod are facing each other

and in direct line of sight.

1.

Press the button on the rotating laser, on the PRA 30 laser receiver and on the PRA 90 automatic

tripod.

◁ The devices are ready for use.

2.

To shift the laser plane up, press the button on the PRA 30 laser receiver or the “up” arrow button on

the PRA 90 automatic tripod.

3.

To shift the laser plane down, press the button on the PRA 30 laser receiver or the “down” arrow

button on the PRA 90 automatic tripod.

5.6 Automatic horizontal alignment 9

The rotating laser is mounted on the PRA 90 automatic tripod.

The PRA 30 laser receiver, the rotating laser and the PRA 90 automatic tripod are paired.

The PRA 30 laser receiver and the control panel of the PRA 90 automatic tripod are facing each other

and in direct line of sight.

1.

Press the button on the rotating laser, on the PRA 30 laser receiver and on the PRA 90 automatic

tripod.

◁ The devices are ready for use.

2. Keep the marking notch on the PRA 30 laser receiver at the height that is to be set. The PRA 30 laser

receiver should be held steady or secured in place.

3.

Begin automatic alignment by double-clicking the button on the PRA 30 laser receiver.

◁ The PRA 90 automatic tripod moves up and down until the correct position is reached. An signal tone

is emitted repeatedly during this procedure.

◁ The rotating laser levels itself once the tripod has reached the correct position. Successful completion

is indicated by a continuous signal tone with a duration of 5 seconds. The symbol is no longer

shown.

▽

If automatic alignment cannot be completed successfully, short signal tones are emitted and the

symbol disappears.

4. Check the height setting in the display.

5. Remove the PRA 30 laser receiver.

6.

Stop automatic alignment before completion by double-clicking the button on the PRA 30 laser

receiver.

5.7 Manual vertical alignment 10

The rotating laser is placed or securely mounted in the vertical position (tripod, wall mount, facade or

batter board adapter, or lying on the rear grips). A reference point (A) is marked below the laser head

(e.g. a nail on a batter board or a spot of paint on the floor or ground).

The PRA 30 laser receiver and the rotating laser are paired.

The PRA 30 laser receiver and the receiving side of the rotating laser are facing each other and in direct

line of sight. The best receiving side of the rotating laser is the side at which the battery is inserted.

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

10 English 2134494

*2134494*

1. Use the visual sighting method on the head to line up the vertical axis of the rotating laser.

2.

Press the button on the rotating laser.

◁ The rotating laser levels itself and then projects a stationary downward-pointing laser beam.

3. Position the rotating laser so that the projected laser beam strikes reference point (A) exactly. Please

note: The reference point is not a plumb point!

4.

To shift the laser plane to the right or left, press the or button on the PRA 30 laser receiver.

◁ The rotating laser begins rotating after pressing one of the two direction arrow buttons.

5.8 Automatic vertical alignment 11

The rotating laser is placed or securely mounted in the vertical position (tripod, wall mount, facade or

batter board adapter, or lying on the rear grips). A reference point (A) is marked below the laser head

(e.g. a nail on a batter board or a spot of paint on the floor or ground).

The PRA 30 laser receiver and the rotating laser are paired.

The PRA 30 laser receiver and the receiving side of the rotating laser are facing each other and in direct

line of sight. The best receiving side of the rotating laser is the side at which the battery is inserted.

1. Use the visual sighting method on the head to line up the vertical axis of the rotating laser.

2.

Press the button on the rotating laser.

◁ The rotating laser levels itself and then projects a stationary downward-pointing laser beam.

3. Position the rotating laser so that the projected laser beam strikes reference point (A) exactly. Please

note: The reference point is not a plumb point!

4. Keep the marking notch on the PRA 30 laser receiver on the plane that is to be set. The PRA 30 laser

receiver should be held steady or secured in place.

5.

Begin automatic alignment by double-clicking the button on the PRA 30 laser receiver.

◁ The head of the rotating laser pivots to the left and right until the desired position is reached. A signal

tone is emitted repeatedly during this procedure.

◁ The rotating laser levels itself once the position has been reached. Successful completion is indicated

by a continuous signal tone with a duration of 5 seconds. The symbol disappears.

◁ The rotating laser switches to surveillance mode. Surveillance when working in the vertical plane

→ page 5

▽

If automatic alignment cannot be completed successfully, short signal tones are emitted and the

symbol disappears.

6. Do NOT remove the PRA 30 laser receiver from the target plane so long as surveillance mode is active.

7.

Double-click the button on the PRA 30 laser receiver.

◁ During automatic alignment: Stops automatic alignment before completion.

◁ In surveillance mode: Ends surveillance mode.

5.9 Setting the inclination using the PRA 79 slope adapter

Depending on the application, the PRA 79 slope adapter can be mounted on a tripod. The angle of

inclination of the PRA 79 slope adapter is set to 0°.

1. Mount the rotating laser on the PRA 79 slope adapter. Observe the operating instructions for the PRA 79

slope adapter. The control panel of the rotating laser should be facing you.

2. Position the rotating laser either at the upper edge or lower edge of the inclined plane.

3.

Press the button on the rotating laser.

◁ The laser switches on, the beam begins to rotate and the “auto leveling” LED lights as soon as the

tool has leveled itself.

4.

Press the button on the rotating laser.

◁ The inclined plane mode LED on the rotating laser then blinks.

5. Set the PRA 79 slope adapter to the desired angle of inclination.

When the angle of inclination is set manually, the rotating laser levels the laser plane once and then

fixes it. Vibration, changes in temperature or other influences that may occur during the course of

the day may affect the position of the laser plane.

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

*2134494*

2134494 English 11

5.10 Setting the inclination manually 11

The rotating laser, depending on the application, is mounted or positioned securely.

The PRA 30 laser receiver and the rotating laser are paired.

The PRA 30 laser receiver and the receiving side of the rotating laser are facing each other and in direct

line of sight. The best receiving side of the rotating laser is the side at which the battery is inserted.

1. Position the rotating laser either at the upper edge or lower edge of the inclined plane.

2. Position yourself behind the rotating laser with the control panel facing you.

3.

Press the button on the rotating laser and the PRA 30 laser receiver.

◁ The laser switches on, the beam begins to rotate and the “auto leveling” LED lights as soon as the

tool has leveled itself.

4.

Press the button on the rotating laser.

◁ The inclined plane mode LED on the rotating laser then blinks.

◁ The inclined plane mode symbol is shown on the PRA 30 laser receiver.

5. Use the target notch on the head of the tool to align the rotating laser parallel to the inclined plane.

6.

To lower the laser plane ahead of the rotating laser, press the on the PRA 30 laser receiver repeatedly

until the desired value is shown in the display.

7.

To raise the laser plane ahead of the rotating laser, press the on the PRA 30 laser receiver repeatedly

until the desired value is shown in the display.

◁ If no button is pressed within 3 seconds, the rotating laser levels itself to the previously set value. The

inclined plane mode LED lights.

A long press of the button causes the entered value to change rapidly.

When the angle of inclination is set manually, the rotating laser levels the laser plane once and then

fixes it. Vibration, changes in temperature or other influences that may occur during the course of

the day may affect the position of the laser plane.

5.11 Setting the inclination automatically 11

The rotating laser, depending on the application, is mounted or positioned securely.

The PRA 30 laser receiver, depending on the application, is mounted on a receiver holder and

telescopic staff.

The PRA 30 laser receiver and the rotating laser are paired.

The PRA 30 laser receiver and the receiving side of the rotating laser are facing each other and in direct

line of sight. The best receiving side of the rotating laser is the side at which the battery is inserted.

1. Position the rotating laser either at the upper edge or lower edge of the inclined plane.

2. Hold the PRA 30 laser receiver right beside the rotating laser and adjust the height the PRA 30 laser

receiver so that the marking notch is at the height of the laser plane. Fix the height of the telescopic staff.

3. Position the telescopic staff with the PRA 30 laser receiver at the other edge of the inclined plane.

4.

Press the button on the rotating laser and the PRA 30 laser receiver.

◁ The laser switches on, the beam begins to rotate and the “auto leveling” LED lights as soon as the

tool has leveled itself.

5.

Press the button on the rotating laser.

◁ The inclined plane mode LED on the rotating laser then blinks.

◁ The inclined plane mode symbol is shown on the PRA 30 laser receiver.

6.

Begin automatic alignment by double-clicking the button on the PRA 30 laser receiver.

◁ The rotating laser inclines the laser plane automatically until the mark at the PRA 30 laser receiver is

reached. An signal tone is emitted repeatedly during this procedure.

◁ The rotating laser levels itself once the position has been reached. Successful completion is indicated

by a continuous signal tone with a duration of 5 seconds. The symbol disappears.

▽

If automatic alignment cannot be completed successfully, short signal tones are emitted and the

indication in the display disappears.

7. Read the inclination from the PRA 30 laser receiver within 5 seconds.

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

12 English 2134494

*2134494*

8.

Stop automatic inclination before completion by double-clicking the button on the PRA 30 laser

receiver.

If the rotating laser begins the automatic search in the wrong direction, press the button to

change the search direction.

5.12 Alignment using electronic inclination alignment (e-targeting)

Electronic inclination alignment optimizes manual alignment of the rotating laser. The electronic

method is more accurate.

The rotating laser, depending on the application, is mounted or positioned securely.

The PRA 30 laser receiver and the rotating laser are paired.

The PRA 30 laser receiver and the receiving side of the rotating laser are facing each other and in direct

line of sight. The best receiving side of the rotating laser is the side at which the battery is inserted.

1. Set the inclination of the laser plane automatically. → page 11

2.

Press the button on the rotating laser.

▽ If both arrows blink, the PRA 30 laser receiver is receiving no signal from the rotating laser.

▶ Use the marking notch on the PRA 30 laser receiver to bring the rotating laser into alignment.

◁

If the left arrow lights , turn the rotating laser clockwise.

◁

If the left right arrow lights , turn the rotating laser counterclockwise.

◁ If both arrows light constantly for 10 seconds, alignment of the PRA 30 laser receiver is correct and

the procedure ends.

3. Secure the rotating laser on the tripod in this position.

4.

Stop electronic inclination alignment before completion by double-clicking the button on the rotating

laser.

5.13 Deactivating the shock warning function

1. Switch the laser on. → page 8

2.

Press the button.

◁ The shock warning deactivation LED lights constantly, indicating that the function has been

deactivated.

To return to standard operating mode, switch the laser tool off and then switch it back on again.

5.14 Activating / deactivating sleep mode

Sleep mode may be activated on the rotating laser during breaks between work or during other

activities. All settings concerning the laser plane or inclination are retained while in this status. Sleep

mode saves power and extends battery life.

Please also refer to “PRA 30 laser receiver menu options” for information about settings.

1. Switch the laser receiver off.

2.

Press the button for 2 seconds.

3.

Press the button twice and go to the sleep mode menu option.

4.

Set the mode by pressing the button. The status set is highlighted in black.

5. After ending sleep mode, check the laser settings in order to ensure continued working accuracy.

Sleep mode remains active for a maximum of 4 hours.

5.15 Checking the main and transverse horizontal axes 14

1. Set up the tripod approx. 20 m (66 ft) from a wall and adjust the tripod head horizontally with a spirit level.

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

*2134494*

2134494 English 13

2. Mount the tool on the tripod and use the visual sighting method (front and rear sights) to aim the tool at

the wall.

3. Fig. a: Use the receiver to catch the laser beam and mark a point (point 1) on the wall.

4. Pivot the tool clockwise through 90° about its own axis. In doing so, ensure that the height of the tool

does not change.

5. Fig. b: Use the laser receiver to catch the laser beam and mark a second point (point 2) on the wall.

6. Fig. c and d: Repeat the two previous steps twice and use the laser receiver to catch the beam and mark

points 3 and 4 on the wall.

If the procedure has been carried out accurately, the vertical distance between the two marked

points 1 and 3 (main axis) or points 2 and 4 (transverse axis) should each be < 2 mm (at 20 m) (0.12"

at 66 ft). If the deviation is greater than this, please return the tool to Hilti Service for calibration.

5.16 Checking the vertical axis 15

1. Place the tool in the vertical position on the floor or ground, which should be as flat as possible, approx.

20 m (66 ft) from a wall.

2. Align the grips parallel to the wall.

3. Switch the tool on and mark the reference point (R) on the ground or floor.

4. With the aid of the receiver, mark point (A) low on the wall.

5. With the aid of the receiver, mark point (B) at a height of approx. 10 m (33 ft).

6. Pivot the tool through 180° and realign it with the reference point (R) on the ground or floor and with point

(A) at the base of the wall.

7. With the aid of the receiver, mark point (C) at a height of approx. 10 m (33 ft).

◁ When this procedure is carried out carefully, the horizontal distance between the two marked points

(B) and (C) should be less than 1.5 mm (at 10 m) (0.06 inch at 33 ft). If the deviation is greater than

this, please return the tool to Hilti Service for calibration.

6 Operating the laser receiver

6.1 Inserting the batteries in the laser receiver 12

▶ Insert the batteries in the laser receiver.

Use only batteries that have been manufactured in accordance with international standards.

6.2 Pairing the rotating laser and the PRA 30 laser receiver

1.

Press the button on both devices for at least 3 seconds.

◁ Successful pairing is confirmed by all LEDs blinking on the rotating laser a signal tone emitted by the

PRA 30 laser receiver. The symbol appears briefly on the laser receiver.

◁ The rotating laser and the laser receiver switch themselves off.

2. Switch the devices on again.

◁

The devices are paired. The symbol is shown on the laser receiver.

6.3 Pairing the PRA 90 tripod and the PRA 30 laser receiver

1.

Press the button on both devices for at least 3 seconds.

◁ Successful pairing is confirmed by all LEDs blinking on the PRA 90 automatic tripod and by a signal

tone emitted by the PRA 30 laser receiver. The symbol appears briefly on the laser receiver.

◁ The automatic tripod and the laser receiver switch themselves off.

2. Switch the devices on again.

◁ The devices are paired. The rotating laser and the automatic tripod are shown in the display on the

laser receiver.

6.4 Using the laser receiver to detect the laser beam

1.

Press the button on the laser receiver.

2. Hold the laser receiver with the receiving window directly in the plane of the laser beam.

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

14 English 2134494

*2134494*

3. Hold the laser receiver still while alignment is taking place and take care to ensure that the line of sight

between the laser receiver and the tool is not obstructed.

◁ Detection of the laser beam is indicated by visual and audible signals.

◁ The laser receiver indicates the distance to the laser beam.

6.5 Setting the units to be used

1.

When switching the laser receiver on, press and hold the button for two seconds.

◁ The menu is then shown in the display.

2.

Use the button to toggle between metric or imperial units of measurement.

3.

Switch off the laser receiver by pressing the button.

◁ The settings will be saved.

6.6 Changing the units used by the laser receiver

1.

When switching the laser receiver on, press and hold the button for two seconds.

◁ The menu is then shown in the display.

2.

Press the button repeatedly.

◁ The desired accuracy (mm/cm/off) is shown alternately in the digital display.

3.

Switch off the laser receiver by pressing the button.

◁ The settings will be saved.

6.7 Adjusting the volume level on the laser receiver

▶

Press the button repeatedly.

◁ The digital display cycles through the volume levels (low/normal/high/off).

“Normal” is the default volume when the laser receiver is switched on.

6.8 Adjusting the signal tone on the laser receiver

1.

When switching the laser receiver on, press and hold the button for two seconds.

◁ The menu is then shown in the display.

2.

Use the button to assign the rapid signal tone to the upper or lower detection area.

3.

Switch the laser receiver off by pressing the button.

◁ The settings will be saved.

6.9 PRA 30 Menu options

The laser receiver is switched off.

Press the button for 2 seconds.

Menu option fig.1 is displayed.

To switch between the menu options, press the or direction buttons.

To save the settings, switch the laser receiver off.

Printed: 08.05.2018 | Doc-Nr: PUB / 5301186 / 000 / 03

Leht laadib ...

Hilti PR 30 Kasutusjuhend

Hilti PR 30 Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid