Samsung SR20H9050U Kasutusjuhend

SR20H9050U Series

SR20H9030U Series

POWERbot

user manual

imagine the possibilities

Thank you for purchasing a Samsung product.

English

 Before operating this unit, please read the instructions carefully.

 For indoor use only.

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 31 2015-02-05 오후 3:06:41

ENGLISH-02

Contents

03

Safety information

08

Installation

Accessories / Installation note

10

Charging

Automatic charging / Recharging / Low

battery (Lo)

12

Installing the Virtual guard

Part name of the Virtual guard /

Inserting batteries

14

Using POWERbot

Turning the power on/off / Using Auto

clean mode / Using the cleaning modes /

Recharging / Selecting cleaning mode

16

Using the remote control

Power/Recharging / Cleaning mode /

Additional function / Direction control /

Point cleaning

18

Name of each part

Top / Bottom / Display panel

19

Setting time/schedule

Setting the time / Setting the schedule

20

Cleaning and maintaining

Cleaning the dustbin / Cleaning the sensors

and the camera / Cleaning the Power brush /

Cleaning the Driving wheel

22

Notes and cautions

Charging / In use / Cleaning and maintenance /

About battery / About the IrDA sensor

24

Error codes

25

Troubleshooting

27

Warnings about battery

28

Open Source Announcement

29

Specifications

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 2 2015-02-05 오후 3:06:27

ENGLISH-03

Safety information

SAFETY INFORMATION

WARNING

• Before operating the appliance, please read this manual thoroughly and retain it

for your reference.

WARNING

• Because these following operating instructions cover various models, the

characteristics of your vacuum cleaner may differ slightly from those described in

this manual.

CAUTION/WARNING SYMBOLS USED

WARNING

Indicates that a danger of death or serious injury exists.

CAUTION

Indicates that a risk of personal injury or material damage exists.

OTHER SYMBOLS USED

NOTE

Indicates that a risk of personal injury or material damage exists.

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 3 2015-02-05 오후 3:06:28

ENGLISH-04

Safety information

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should be observed, including the

following:

READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot.

Unplug from outlet when not in use and before conducting maintenance.

WARNING: to reduce the risk of fire, electric shock, or injury:

GENERAL

•Use only as described in this manual.

•Do not operate POWERbot or charger (station) if it has been damaged in any way.

•If the vacuum cleaner is not working as it should, has been dropped, damaged, left

outdoors, or dropped in water, return it to a customer care center.

•Do not handle the charger (station) or POWERbot with wet hands.

•Use only on dry, indoor surfaces.

•This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge

if they have been given supervision or instruction concerning use of the appliance in a

safe way and understand the hazards involved.

•Children shall not play with the appliance. Cleaning and user maintenance shall not be

made by children without supervision.

BATTERY Charger (station)

•Do not modify the polarized plug to fit a non-polarized outlet or extension cord.

•Do not use outdoors or on wet surfaces.

•Unplug the charger (station) from the outlet when not in use and before servicing.

•Use only the charger (station) supplied by the manufacturer to recharge.

•Do not use with a damaged cord or plug or a loose power outlet.

•Do not pull or carry by the cord, use the cord as a handle, close the door on the cord,

or pull the cord around sharp edges or corners. Keep the cord away from heated

surfaces.

•Do not use extension cords or outlets with inadequate current carrying capacity.

•Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

•Do not mutilate or incinerate batteries as they will explode at high temperatures.

•Do not attempt to open the charger (station). Repairs should only be carried out by a

qualified customer care center.

•Do not expose the charger (station) to high temperatures or allow moisture or humidity

of any kind to come into contact with the charger (station).

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 4 2015-02-05 오후 3:06:28

ENGLISH-05

POWERbot

•Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc.

•Do not use without a filter in place. When servicing the unit, never put fingers or other

objects into the fan chamber in case the unit accidentally turns on.

•Do not put any objects into openings. Do not use with any openings blocked; keep

openings free of dust, lint, hair, and anything that may reduce air flow.

•Do not pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).

•Do not pick up anything that is burning or smoke, such as cigarettes, matches, or hot

ashes.

•Do not use to pick up flammable or combustible liquids such as gasoline, nor use on

areas where they may be present.

•Locations with candles or desk lamps on the floor.

•Locations with unattended fires (fire or embers).

•Locations with distilled alcohol, thinner, ashtrays with burning cigarettes, etc.

•Do not use POWERbot in an enclosed space filled with vapours given off by oil based

paint, paint thinner, moth proofing substances, flammable dust, or other explosive or

toxic vapours.

•Leaks from battery cells can occur under extreme usage or temperature conditions.

If the liquid gets on skin, wash quickly with water. If the liquid gets into the eyes,

flush them immediately with clean water for a minimum of 10 minutes. Seek medical

attention.

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 5 2015-02-05 오후 3:06:28

ENGLISH-06

WARNING

Power related

f Please prevent any risk of electric shock or

fire.

– Do not damage the power cord.

– Do not pull the power cord too hard or touch

the power plug with wet hands.

– Do not use a power source other than 100-

240 V~ and also do not use a multi outlet to

supply power to number of devices at the same

time. (Do not leave the cord carelessly on the

floor.)

– Do not use a damaged power plug, power cord

or loose power outlet.

f Clean dust or any foreign matters on the pin

and contact part of the power plug.

– There is a risk of electric shock or malfunction.

WARNING

Before use

f Do not use POWERbot near combustible

materials.

– Place near candle, desktop lamps, fireplace or

near combustible materials such as gasoline,

alcohol, thinners etc.

f The POWERbot is intended for household

use therefore do not use it in an attic,

basement, storage, industrial building, out of

indoor space, places with moisture (such as

bathroom, laundry), on the table or shelves.

– The POWERbot can be damaged or

malfunction.

f Install the Virtual guard in front of dangerous

areas (such as stairs or railings) to prevent

damaging the product or getting injured.

– For your safety, always keep the cliff sensor

clean.

f Be sure POWERbot does not pass through or

touch any kind of liquids.

– The POWERbot can be severely damaged and

it may contaminate other areas if the wheels

pass through liquid.

f Do not spill any liquids on the charger.

– There is a risk of fire or electric shock.

f Do not use the charger for anything other

than its intended purpose.

– There is a risk of fire or severe damage to the

charger.

f Always keep the cliff sensor clean for your

safety.

WARNING

In use

f If any abnormal sounds, smells or smoke

come from POWERbot, immediately shut

off the emergency switch at the bottom of

POWERbot and contact a service center.

WARNING

Cleaning and

maintenance

f When power cord is damaged, contact a

service center to get it replaced by certified

repairman.

– There is a risk of fire or electric shock.

f Please check with a Samsung Electronics

service center when exchanging batteries.

– Using batteries from other products can cause

malfunction.

Safety information

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 6 2015-02-05 오후 3:06:28

ENGLISH-07

CAUTION

Before use

f Insert the dustbin before using POWERbot.

f Open room doors before cleaning in order

to have all rooms cleaned and install a

Virtual guard in front of entryway, balconies,

bathrooms, or other areas where POWERbot

may fall.

f Be careful with the followings for proper

automatic recharging.

– Always turn on the power of the charger.

– Install the charger where POWERbot can easily

find.

– Do not leave any object in front of the charger.

f When installing the charger, do not leave the

cord carelessly on the floor since POWERbot

may get tangled by it.

f Do not use POWERbot on black colored

floors.

– The POWERbot may not be able to operate

normally.

f Do not pick up POWERbot by the dustbin

holder.

f Do not place any objects within 0.5 m to both

sides and 1 m to the front of the charger.

f Make sure the charger's charging contact is

not damaged or have any foreign matters on

it.

f Do not install the charger in an area with a

dark floor.

– If the floor around the charger is dark,

recharging is hindered.

f Move any obstacles that may disturb

POWERbot's movement (such as children's

indoor swing or slides) before cleaning.

CAUTION

In use

f Using POWERbot on thick carpet may

damage both POWERbot and the carpet.

– The POWERbot cannot pass over carpet that is

thicker than 1 cm.

f Do not use POWERbot on tables or other

high surfaces.

– There is a risk of damage if it falls.

f The POWERbot may bump into chair, desk

legs therefore move them away for faster and

efficient cleaning.

f When POWERbot is operating, do not lift it up

or carry it to another area.

f Do not hold by driving wheels of POWERbot

when carrying it to another area.

f Do not put any objects on top of POWERbot

since it may cause malfunction.

f Remove any large papers or plastic bags

immediately when using POWERbot since

they may block the intake.

f Do not aim the red pointer directly at people

or animals.

CAUTION

Cleaning and

maintenance

f Prevent any damage to POWERbot by

complying the followings.

– Do not clean POWERbot by spraying water

directly onto it or use benzene, thinner, acetone

or alcohol to clean it.

f Do not disassemble or repair POWERbot.

This should only be done by a certified

repairman.

f Always keep the obstacle sensor and cliff

sensor clean.

– If foreign matter accumulates, sensors may

malfunction.

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 7 2015-02-05 오후 3:06:28

ENGLISH-08

1

Connect the

adapter jack to

the charger

2

Connect the

power cord to

the adapter

When using the adapter,

the side with the sticker

attached must face down.

3

Connect the

power plug to

the outlet

Power lamp (Red) will turn

on.

Installation

Power of the charger must be on at all times.

DC-IN

Power lamp (Red)

About 1 m

About 0.5 m

Install it in a place without obstacles

and danger of falling.

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 8 2015-02-05 오후 3:06:28

ENGLISH-09

Accessories

Remote control Batteries (AAA type) User manual/Quick

guide

Spare filter

Cleaning brush Power cord Adapter Virtual guard

Installation note

Note

f Install charger in a place where the floor and wall are level.

f It is best to install the charger along the grain of wooden floors.

f If the emergency switch is off, POWERbot will not charge even if it is docked on the charger.

f Always turn on the power of the charger.

– If power is not supplied to the charger, POWERbot cannot find it and cannot automatically recharge.

– If POWERbot is left detached from the charger, the battery will drain naturally.

f If POWERbot is in energy-saving mode, power will not come on even if the emergency switch is

turned off and then on. Press and hold the [Start/Stop] button on POWERbot.

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 9 2015-02-05 오후 3:06:29

ENGLISH-10

Charging lamp during charging (green)

It takes approximately 160 minutes to

completely charge when charging for the

first time after purchase and can be used for

approximately 60 minutes.

Charging

1

Turn on the

emergency switch

on the bottom

You must turn on the

emergency switch to turn on

POWERbot.

2

Manually charge

POWERbot by

placing it on the

charger

Make sure charge pins of

POWERbot and the charger is

aligned.

3

Check the

charging status

“ ” will turn on

according to charging

progress and "FULL" will

turn on when charging is

complete.

WARNING

• Rated input voltage of this product

is 100-240 V~.

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 10 2015-02-05 오후 3:06:29

ENGLISH-11

When the battery indicator blinks

during cleaning, POWERbot will

return to the charger to charge itself

automatically.

Automatic charging

You may command POWERbot to

recharge at the charger while it is in

cleaning process.

Recharging

Manually charge POWERbot by

placing it on the charger.

Low battery (Lo)

Steps to take if recharging is not being executed

Check the installation status of the

charger when:

fcharger is located in a place where POWERbot

cannot easily access

fdistance of the charger and POWERbot is over 5 m

apart

– It may take a long time for POWERbot to return to

the charger for recharging

Manually charge POWERbot when:

fcharger is located in a corner

fbattery is fully exhausted

fPOWERbot is stuck by obstacles (furniture etc.)

fPOWERbot can't climb threshold near charger

(Height of the threshold that POWERbot can climb:

about 1.5 cm and below)

fwhen battery indicator blinks and "Lo" is displayed

fwhen POWERbot is set on Spot clean or Manual

clean mode

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 11 2015-02-05 오후 3:06:30

ENGLISH-12

Installing the Virtual guard

Infrared ray from the Virtual guard will restrict POWERbot from approaching certain

area.

Virtual guard

1

Press the Power

button to turn it on

Power lamp (Red) will blink.

2

Install the Virtual guard

where you want to restrict

POWERbot's entrance

Make sure that distance sensor is facing

at the desired direction you want to

create a invisible barrier (which will restrict

POWERbot's approach).

The distance of virtual wall is 2.5 m at minimum and may differ

depending on surroundings and movement status of POWERbot.

Minimum 2.5 m

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 12 2015-02-05 오후 3:06:30

ENGLISH-13

Part name of the Virtual guard

Power button

Distance detection sensor

(Infrared ray sensor)

Power lamp

Power on: Red lamp blinks

Power off: Lamp is off

POWERbot detection sensor

Battery cover

Inserting batteries

Batteries for Virtual guard must be purchased separately.

1

Open the battery cover

of the Virtual guard by

pressing the locking

tab and lift it up.

2

Insert the alkaline

batteries (D type) as

shown in the illustration

(check the +, - polarity).

3

Insert the tip of the

cover into the slot and

push the other end to

close the battery cover.

 Specification: type D (LR20) batteries

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 13 2015-02-05 오후 3:06:31

ENGLISH-14

Using POWERbot

You must turn on the emergency switch before using POWERbot.

Turning the power on/off

Press the button for more than

3 seconds

Using Auto clean mode

The POWERbot moves and cleans

automatically until it cleans entire space once.

 Stop cleaning: Press the button shortly

Recharging

You may command POWERbot to recharge at

the charger automatically while it is in cleaning

process.

Using the cleaning

modes

You can select the desired cleaning mode.

WARNING

• When POWERbot is not used for

30 minutes, power will turn off

automatically.

– You can turn on the power only by

using the buttons on POWERbot.

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 14 2015-02-05 오후 3:06:31

ENGLISH-15

Cleaning mode How to select Displayed icon

Auto clean

Press once

Spot clean

Press twice

Max clean

Press 3 times

Manual clean

Press 4 times

 Direction control can be done only

by the remote control.

 When POWERbot is being charged, you can only select the Auto clean or Max clean mode.

 When cleaning is done within 15 minutes in Auto clean mode, the cleaner will repeat cleaning one

more time.

Cleaning method for each modes

About 1.5 m

Auto clean

Cleans automatically

until entire space is

cleaned once.

Spot clean

Cleans a localized area

intensely. It can be

used to clean bread or

cookie crumbs.

Max clean

Cleans until the battery

is depleted.

Manual clean

You can move

POWERbot with the

remote control to clean

the desired spot.

Selecting cleaning mode

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 15 2015-02-05 오후 3:06:32

ENGLISH-16

Using the remote control

1 Power/Recharging

[A Type] [B Type]

Power

Turn POWERbot's power on/off

Recharging

Select to recharge POWERbot at the charger while it

is in cleaning process

2 Cleaning mode

Auto clean

Select to automatically clean the entire space once

Spot clean

Select to clean a localized area intensely

Max clean

Select to make POWERbot to clean until battery

indicator flashes after reaching down to one level

Manual clean

Select to manually control and clean by using the

remote control

Start/Stop

Select to start or stop cleaning process

3 Additional function

Silence mode

Select to clean with lower operation noise

 Turbo mode is not available

Dust sensor

mode

In Auto clean mode

fWhen dust intake is detected, suction of

POWERbot will become stronger and it will move

around that area to focuses on cleaning the

surrounding area.

In Spot/Max/Manual clean

fWhen dust intake is detected, suction of

POWERbot will become stronger.

Sound

Each time you press this button, Sound Effects 

Mute is selected in this sequence.

 Remote control function NOT supported.

Inserting batteries

Open the battery cover by lifting it up

while pressing the locking tab and

insert the batteries as shown in the

illustration. Then, close the cover until

it clicks into place.

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 16 2015-02-05 오후 3:06:33

ENGLISH-17

You can use the remote control to point and clean

the desired spot while POWERbot is in cleaning

process.

Point the red light on the floor within 50 cm around

POWERbot's location.

Press and hold the Point cleaning button to move the red light to

the desired spot. The POWERbot will follow the light while cleaning.

50 cm

Operating distance of the remote control

Height of the remote

control

Operating distance

Height of the remote

control

0.5 m 1 m 1.5 m

Operating distance About 1.5 m About 2 m About 3 m

5 Point cleaning

– Only available in A type remote controll

[A Type]

1

2

4

3

Refer to

page 19

 N/A

5

[B Type]

1

2

4

Refer to

page 19

3

4 Direction control

[A Type] [B Type]

Select to move forward

Select to turn left

Select to turn right

 Moving backward is not available

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 17 2015-02-05 오후 3:06:34

ENGLISH-18

Name of each part

1

5

2

3

4

6

3

4

7

8

9

Top

1. Display panel

2. Dustbin holder

3. Remote control signal receiver

4. Virtual guard sensor

5. Obstacle sensor

6. Dustbin

7. Camera

8. Dustbin handle

9. Bumper sensor

1

4

2

6

5

4

7

4

8

9

3

Bottom

1. Charge pins

2. Power brush

3. Power brush cover

4. Cliff sensor

5. Roller

6. Battery cover

7. Power brush cover button

8. Driving wheel

9. Emergency switch

11 127 1098

5

6

14

15

1

3

2

4

13

Display panel

1. Mute

2. Error indicator (Refer to page 24)

3. One-time/Daily schedule

4. Filter inspection

5. Battery indicator

6. Number display

7. Auto clean

8. Spot clean

9. Max clean

10. Manual clean

11. Silence mode

12. Dust sensor mode

13. Cleaning mode button

14. Recharging button

15. Start/Stop button

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 18 2015-02-05 오후 3:06:35

ENGLISH-19

Setting time/schedule

B type remote control's , , buttons works in same manner as A type remote

control.

Setting the time

You must set the current time before using the One-time/daily schedule.

Start setting Select "Hour" Select "Minute"

Select "AM/PM"Setting complete

or

Skip to previous, next setting

Setting the schedule

Setting/cancelling the schedule can only be done while POWERbot is docked on the charger.

Start setting

Select "One-time" or

"Daily" schedule

Select "Hour" Select "Minute"

Select "AM/PM"Select cleaning mode

Only Auto clean/Max clean

can be selected

Setting complete

or

Skip to previous, next setting

Cancelling

during setup

fSetting will be canceled automatically when there's no input

for 1 minute.

Cancelling One-time/Daily schedule

When both One-time/

Daily schedule is set

Press for 3 sec. Select the schedule Cancel complete

When either one of

One-time or Daily

schedule is set

Press for 3 sec.

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 19 2015-02-05 오후 3:06:36

ENGLISH-20

Cleaning and maintaining

You must turn off the emergency switch before cleaning POWERbot.

Cleaning the dustbin

Clean the dustbin when filter inspection indicator ( ) turns on or if there's too much dust in the dustbin.

1

Remove the dustbin

2

Remove the dustbin

cover

3

Remove dust in the

dustbin and cyclone

unit

"Click"

4

Detach the cyclone unit

from the dustbin cover

then wash the dustbin

and the filter

5

Reassemble the

dustbin

6

Reinsert the dustbin

into the main body until

it clicks

Cleaning the sensors and the camera

Lightly wipe with soft cloth.

Camera

Front sensor

window

Rear sensor

window

Cliff sensors

SR20H9050U_EN_DJ68-00716M-01_Baltic.indd 20 2015-02-05 오후 3:06:37

Leht laaditakse ...

Samsung SR20H9050U Kasutusjuhend

Samsung SR20H9050U Kasutusjuhend

Seotud paberid