Cascade 10H Original Instructions Manual

Bränd: Cascade

Mudel: 10H

Tüüp: Original Instructions Manual

cascade



corporation

NSTALLATION INSTRUCTIONS

and PERIODIC MAINTENANCE

Cascade is a Registered Trademark of Cascade Corporation

H-Series

Swing Frame Paper

Roll Clamps

Number 6095756-R2 EN

Original Instructions

CONTENTS

INTRODUCTION

6095756-R2 EN

Introduction i

Special Definitions 1

Recommended Hydraulic Supply 1

Truck Requirements 2

Swing Control Valve Installation 3

Attachment Installation 8

Periodic Maintenance 15

Nameplate Icons 17

This manual provides installation instructions and periodic

maintenance requirements for the Cascade H-Series Swing

Frame Paper Roll Clamps.

In any communication about the attachment refer to the

product catalog and serial numbers stamped on the

nameplate. If the nameplate is missing, the numbers can

be found stamped on the front of the faceplate top or side.

IMPORTANT: Supply input fittings are JIC.

NOTE: Specifications are shown in Metric units. All

fasteners have a torque value range of ±10% of stated

value.

30H-RES-B001

VER756971

RC3753.eps

30H-RES-B001

VER756971

Nameplate

6095756-R2 EN

SPECIAL DEFINITIONS

RECOMMENDED HYDRAULIC SUPPLY

The statements shown appear throughout this manual

where special emphasis is required. Read all WARNINGS

and CAUTIONS before proceedings with any work.

Statements labeled IMPORTANT and NOTE are special

information that is useful when servicing the attachment.

WARNING – A statement preceded by a

WARNING is information that should be

acted upon to prevent bodily injury. A

WARNING is always inside a ruled box.

CAUTION – A statement preceded by CAUTION is

information that should be acted upon to prevent machine

damaged.

IMPORTANT – A statement preceded by IMPORTANT is

information that possesses special significance.

NOTE – A statement preceded by NOTE is information that

is handy to know and may make the job easier.

H-Series Swing Frame Paper Roll Clamps will require one

of the hydraulic arrangements shown. Refer to Cascade

Hose and Cable Reel Selection Guide, Part No. 212199,

to select the correct hose reel for the mast and truck. The

hose and fitting requirements are:

• Rotate Function – Hoses and fittings should be No. 8

with 10 mm minimum ID.

• Clamp & Swing Functions – Hoses and fittings should

be No. 8 with 10 mm minimum ID, except for internal

reeving arrangements where hoses and fittings may be

No. 6 minimum with 7 mm minimum ID.

A and B

RH THINLINE

2-Port Hose Reel Group and

LH THINLINE

4-port Hose Reel Group

A,B and C

RH and LH THINLINE

2-port Hose Reel Groups and

Mast Single Internal Hose Reeving Group

A and C

RH THINLINE

2-Port Hose Reel Group and

Mast Double Internal Hose Reeving Group

GA0033.eps

CAUTION: Rotate function supply circuit back pressure

exceeding 35 bar and a maximum flow rate of 54 L/min.

can result in excessive oil heating, reduced attachment

performance and shortened hydraulic system life.

Check for restrictions such as numerous fittings and

fitting/hose sizes less than No. 8.

Weighted Emission Sound Pressure Level - Weighted

emission sound pressure level (LA) does not exceed 70

dB(A).

Measured Value of Whole Body Vibration - Measured

value of whole body vibration (m/s

) does not exceed 0,5

m/s

Measured Value of Hand-Arm Vibration - Measured value

of hand-arm vibration (m/s

) does not exceed 2,5 m/s

TRUCK REQUIREMENTS

6095756-R2 EN

GA0137.eps

Carriage Mount Dimension (A) ITA (ISO)

Minimum Maximum

Class II

Class III

Class IV

380.0 mm

474.5 mm

595.5 mm

381.0 mm

476.0 mm

597.0 mm

Truck Relief Setting

140 bar Recommended

160 bar Maximum

Truck Flow Volume

➀

22H–33H Min.

➁

Recommended Max.

➂

Rotate/Clamp 18 L/min. 37 L/min. 56 L/min.

Swing 4 L/min. 7.5 L/min. 12 L/min.

➀ Cascade H-Series Swing Frame Paper Roll Clamps are compatible

with SAE 10W petroleum base hydraulic fluid meeting Mil. Spec.

MIL-0-5606 or MIL-0-2104B. Use of synthetic or aqueous base

hydraulic fluid is not recommended. If fire resistant hydraulic fluid

is required, special seals must be used. Contact Cascade.

➁ Flow less than recommended will result in rotate speed less than

2 RPM.

➂ Flow greater than maximum can result in excessive heating,

reduced system performance and short hydraulic system life.

GA0028.eps

Carriage

Clean and inspect carriage bars for

damage and smoothness. Repair any

protruding welds or damaged notches.

WARNING: Rated capacity of the truck/attachment

combination is a responsibility of the original truck

manufacturer and may be less than that shown

on the attachment nameplate. Consult the truck

nameplate.

Auxiliary Valve Functions

Check for compliance with ANSI (ISO) standards.

GA0082.eps

Hoist Down

Hoist Up

Tilt

Forward

Tilt Back

Rotate

CCW

Swing

Extend

Rotate

Swing

Retract

Release

Clamp

INSTALLATION

6095756-R2 EN

Swing Control Valve Installation

Follow the steps shown to install a Swing Frame Paper Roll

Clamp. Read and understand all WARNING statements.

If you don't understand a procedure, ask your supervisor

or call the nearest Cascade Service Department for

assistance.

NOTE: Swing Frame Clamps require a solenoid-operated

control valve group to convert a two function auxiliary

control valve to three function operation.

For hose reel information, refer to Installation Instructions

673835 for THINLINE

2-Port Hose Reels and Installation

Instructions 675395 for THINELINE

2-Port Hose Reels (for

masts without internal reeving). Control valve groups for

different voltages are listed in the table shown.

Determine an appropriate mounting location for

the control valve on the truck cowl. The valve can

be mounted horizontally or vertically. The valve

must not extend outside the width of the cowl or

interfere with the truck mast.

Assemble the solenoid valve, fittings, cover and

subplate. Position the assembly on the truck cowl

noting any clearance problems.

Control Valve Group

With Knob

Part Number

With Low

Profile Switch

Part Number Truck Voltage

674924

674925

674926

674927

6014883

6014885

6014886

6014887

12V

24V

36V

48V

RC0725.eps

HORIZONTAL MOUNT

VERTICAL MOUNT

Check for

interference

with mast

tilted back

Valve must not

extend outside

width of cowl

RC0726.eps

To RH 2-Port Hose

Reel (No. 8 SAE)

To RH 2-Port Hose

Reel (No. 8 SAE)

To LH -Port or

2-Port Hose Reel

(No. 6 SAE)

To LH -Port or

2-Port Hose Reel

(No. 6 SAE)

NOTE: Solenoid coil

must be rotated 90

degrees to clear cover

when assembled.

To truck auxiliary

valve ports (No. 8)

To truck auxiliary valve

ports (No. 8 SAE)

INSTALLATION

6095756-R2 EN

RC0729.eps

Mark the mounting location on the truck cowl.

Grind and clean the area in preparation for

welding. Tack-weld the subplate to the cowl

and mount the valve to the subplate with the

capscrews supplied in the kit.

Rotate Function – Measure and assemble two

hoses (user-supplied) to run from the control valve

C1 and C4 ports to the RH hose reel. Install

hoses.

Swing Function – Measure and assemble two

hoses (user-supplied) to run from the control valve

C2 and C3 ports to the LH 4-port hose reel 3 and

4 ports. Install hoses.

Measure and assembly two hoses (user-supplied)

to run from the solenoid valve P and T ports to the

truck valve ports. Install the hoses.

IMPORTANT: Proceed to step 7 if lift truck is

equipped with mast internal hose reeving.

Swing Control Valve Installation

RC0727.eps

NOTE: Horizontal

mount only shown

Tack-weld subplate

to truck cowl

8mm x 90mm long

capscrews

RC0728.eps

Truck Auxiliary

Valve Ports

Port T

Port P

Installation with RH 2-Port and LH 4-Port

Hose Reels

RH 2-port

Hose Reel

LH 4-Port

Hose Reel

ROTATE

Function

Ports 1 and 2

for CLAMP/

OPEN circuit

only

SWING

Function

INSTALLATION

6095756-R2 EN

Clamp Function – Measure and assemble two

hoses (user-supplied) to run from the truck valve

ports to the LH 4-port hose reel 1 and 2 ports.

Install hoses.

WARNING: The hose operating

the OPEN function must connect to

Port 1 on the 4-port hose reel.

RC0730.eps

LH 4-Port

Hose Reel

OPEN

function

(Port 1)

CLAMP

function

(Port 2)

Truck Auxiliary

Valve Ports

RC0731.eps

Truck Auxiliary

Valve with

pushbutton

(ROTATE and

SWING

Truck Auxiliary

Valve (CLAMP)

ROTATE

Function

Carriage

Hose

Terminal

RH 2-Port

Hose Reel

Solenoid-operated

Control Valve

SWING

Function

LH 4-Port

Hose Reel

CLAMP/OPEN

Function

Installation with RH 2-Port and LH 4-Port

Hose Reels (Continued)

INSTALLATION

6095756-R2 EN

Rotate Function – Measure and assemble two

hoses (user-supplied) to run from the control valve

C1 and C4 ports to the RH hose reel. Install

hoses.

Swing Function – Measure and assemble two

hoses (user-supplied) to run from the control valve

C2 and C3 ports to the internal hose reeving

hoses. Install hoses.

Installation with RH and LH 2-Port Hose

Reels and Internal Hose Reeving

Clamp Function – Measure and assemble two

hoses (user-supplied) to run from the truck valve

ports to the LH 2-port hose reel. Install hoses.

RC0732.eps

RC0733.eps

RC0734.eps

RH 2-Port

Hose Reel

LH 2-Port

Hose Reel

SWING

Function

ROTATE

Function

CLAMP

Function

Internal

Reeving

Hoses

Truck Auxiliary

Valve Ports

LH 2-Port

Hose Reel

Carriage

Hose

Terminal

Carriage

Hose

Terminal

Carriage

Hose

Terminal

CLAMP/OPEN

Function

SWING

Function

RH 2-Port

Hose Reel

ROTATE

Function

Solenoid-

Operated

Control Valve

Truck Auxiliary

Valve (CLAMP)

Truck Auxiliary Valve

with Pushbutton

(ROTATE and SWING)

Swing Control Valve Installation

INSTALLATION

6095756-R2 EN

Locate the auxiliary valve lever that operates the

hydraulic hoses connected to the solenoid control

valve P and T ports. Install a new knob with

pushbutton, or shrink-wrap low profile switch onto

the control lever.

IMPORTANT: Lever should control the ROTATE

function per ANSI (ISO) standard. When the

pushbutton is depressed, the lever should activate

the SWING function.

CAUTION: Secure cable with cable ties to avoid

pinching at truck cowl during handle movement.

Connect the wiring from the pushbutton and

control valve terminals to the truck electrical

system as shown.

IMPORTANT: Fuse must be connected to an

unswitched positive terminal – control valve must

be able to energize with truck key in off position.

AC0234.eps

AC0402.eps

LOW PROFILE SWITCH ON CONTROL LEVER

SOLENOID KNOB WITH PUSHBUTTON

Pushbutton switch

shrink-wrapped to

control lever

Cable Ties

Foam Tape

Heat-Shrink Tubing

ROTATE Control Lever

75 mm typical

NOTE: Remove

tubing around

button as desired

New knob with pushbutton

(ROTATE Control Lever)

Cable Ties

RC0736.eps

7.5 Amp Fuse

Pushbutton

White

Black

Diode

Coil

Control Knob

with Pushbutton

Solenoid Coil

Control Valve

Truck

Power

Source

(unswitched)

Diode

IMPORTANT: Banded

end must connect to

positive (+) side of

circuit

Cable

Low profile

switch wrapped

to control lever

INSTALLATION

6095756-R2 EN

RC3754.eps

Attachment Installation

Attach overhead hoist

Remove banding, set the attachment upright on

pallet.

B If equipped, remove bolt-on lower mounting

hooks.

Unlock quick-change lower

mounting hooks (if equipped)

Move hooks into unlocked position

(pin in lower hole).

cascade

C-675514-1

CL0097.eps

Guide

LH Lower

Hook

NOTE: Guides can be reversed

to change hook-to-carriage

clearance. Refer to step 7.

16 mm

offset on top

provides

maximum

clearance

Tighten capscrews to:

Class II/III – 165 Nm

Class IV – 320 Nm

WARNING: Verify that the overhead

hoist and chains or straps are rated for

the weight of the attachment. Refer to

nameplate for attachment weight.

INSTALLATION

6095756-R2 EN

Prepare hoses

Position truck carriage behind the attachment.

B Determine hose lengths required.

C Cut hoses to length, install end fittings.

CAUTION: Hoses should be 160 bar working

pressure rated for all attachment functions.

INSTALLATION USING RH & LH 2-PORT

THINLINE

HOSE REELS, SINGLE IHR:

INSTALLATION USING RH 2-PORT HOSE

REEL and LH 4-PORT HOSE REEL:

WARNING: Hose connecting revolving

connection OPEN port to 4-port hose reel

must be connected to outer-most hose on

reel only.

RC3755.eps

RC3756.eps

Release

Clamp

Rotate CCW

Rotate

CCW

Rotate CW

Rotate

Swing Left

Swing Right

CAUTION: Rotate function supply circuit back pressure

exceeding 35 bar and a maximum flow rate of 54 L/min.

can result in excessive oil heating, reduced attachment

performance and shortened hydraulic system life.

Check for restrictions such as numerous fittings and

fitting/hose sizes less than No. 8.

Flush hydraulic supply hoses

Install hoses as shown below.

B Operate auxiliary valves for 30 seconds.

C Remove union fittings.

D Install hoses to revolving connection fittings as

shown in step 3, above.

RC0748.eps

INSTALLATION

6095756-R2 EN

Check lubricant level and

remove rubber vent cover

RC0139.eps

Level must

be up to fill

plug hole

Remove rubber

vent cover

If necessary, fill gearbox with Cascade Gear

Lube 656300 or equivaent SAE 90 wt. gear lube

(AGMA 'mild' 6EP Gear Oil).

RC3757.eps

Mount attachment on truck carriage

Center truck behind attachment.

B Tilt forward and raise carriage into position.

C Engage top mounting hooks with carriage.

Make sure left hook engages closest notch on

top carriage bar

D Lift attachment 5 cm off pallet.

GA0079.eps

Class II – 15-17 mm

Class III – 18-20 mm

Class IV – 18-20 mm

Class II – 8-9 mm

Class III – 10-11 mm

Class IV – 12-13 mm

Carriage Bar

and Upper

Mounting Hook

Center Spacer

Engage locator

tab in notch

Upper

Carriage Bar

Notch

Connect hoses to

end block before

attachment installation

Attachment Installation

INSTALLATION

6095756-R2 EN

Install and engage lower hooks

ADJUST

RC1130.eps

cascade

C-675514-1

RC1131.eps

BOLT-ON TYPE

QUICK-CHANGE TYPE

Lower

Carriage

Bar

Lower

Carriage

Bar

Install hooks,

tap light into

position

Tighten capscrews:

Class II/III – 165 Nm

Class IV – 265 Nm

Inspect hooks for

excessive clearance.

Reverse guides to

change clearance.

Refer to step 2.

Slide hook up

to engage bar,

install pin in

locked position

(upper hole).

5 mm

maximum

Connect hoses to hose terminal

fittings as shown in step 3

INSTALLATION USING Rh & LH 2-PORT

THINLINE

HOSE REELS, SINGLE IHR:

INSTALLATION USING RH 2-PORT HOSE

REEL and LH 4-PORT HOSE REEL:

RC3758.eps

RC3759.eps

Clamp/

Release

Clamp/

Release

Rotate

CW/CCW

Rotate

CW/CCW

Swing

RH/LH

Swing

RH/LH

INSTALLATION

6095756-R2 EN

Attachment Installation

Install stop block kit

• Preheat each stop block and carriage bar weld

area to 180° C.

• Use AWS E-7018 low hydrogen rod and weld a

6 mm fillet full length on three side of each stop

block.

RC0224.eps

RH Upper

Mounting Hook

Steel Stop

Blocks

(both sides)

6 mm fillet

weld on three

sides

Truck Upper

Carriage Bar

NOTE: Do not weld

stop block on inside

1.5 mm

180° Stop Valve Adjustment

(if equipped/required)

WARNING: Make sure all personnel are

clear of attachment during adjustment.

A Loosen the jam nut on the stop valve adjustment

screws and turn the screws OUT (counterclockwise)

until a groove marking the maximum-out position

is visible. Adjustment screws should be adjusted

equally.

IMPORTANT: Backing the adjustment screws out

past the groove will cause hydraulic leakage.

B Using a load that: A) is the heaviest to be lifted,

or B) requires maximum motor torque, rotate the

attachment back and forth to the stops at full

speed for 1–2 minutes before making adjustments.

Observe whether the attachment fully completes its

rotation slowly into the hard stop.

C If rotation does not continue into the hard stop,

rotate the stop valve off the ramp and turn the

adjustment screw IN (clockwise) one-eighth turn.

Test for complete rotation slowly into the hard stop.

D Repeat Step C until the attachment fully completes

its rotation slowly into the hard stop. Tighten the jam

nut on the adjustment screw.

E Check the torque on the stop block capscrews and

tighten to 110 Nm if necessary.

RC2845.eps

Adjustment

Screw and

Jam Nut

Stop

Block

Ramp

180°

Stop

Valve

INSTALLATION

6095756-R2 EN

Electronic Rotational Control

(ERC) Stop Adjustment

(if equipped/required)

Rotate the attachment in each direction to verify it

stops in vertical and horizontal (bilge) position.

• If rotation does not stop at vertical or bilge

position, refer to troubleshooting section in the

service manual.

• If attachment stops in vertical and horizontal

(bilge) positions, proceed to Step B.

• If rotation does no stop at exact vertical or bilge

positions, limit switches may be adjusted as

described in Step D.

B Wait 3 seconds to rotate attachment again, verifying

it again stops in the vertical or horizontal (bilge)

positions.

C Press and hold override pushbutton and verify

that the attachment will rotate continuously without

stopping.

• If continuous rotation does not occur when

holding pushbutton, refer to troubleshooting

section in the service manual.

D Inspect limit switch end rollers for full engagement

on deceleration ramps and stop capscrews. If

required, adjust limit switch position and/or stop

capscrew to precisely locate stop position within 13

mm.

AC0231.eps

Rotational Control stops

clamp at vertical positions

A top, B bottom and C

bilge position.

To continue rotation after

stopping, wait 3 seconds,

OR press override button.

For continuous rotation,

press and hold button.

AC1214.eps

Limit Switches

(Normally Open)

Deceleration/Stop Ramp

INSTALLATION

6095756-R2 EN

RC3760.eps

Cycle Attachment Functions

WARNING: Make sure all personnel

are clear of the attachment during

testing.

• With no load, cycle all functions several times.

• Check functions for operation in accordance

with ANSI (ISO) standards.

• Clamp and rotate a maximum load, check for

smoothness and normal rotation.

• Check for leaks at fittings, revolving connection

and cylinder rod ends.

SWING

(Bilge handling shown)

A Push Button - Extend

B Push Button - Retract

LONG ARM

(Vertical & horizontal

positions only)

C Release

D Clamp

ROTATE

(Driver's view)

A Counterclockwise (CCW)

B Clockwise (CW)

SHORT ARM

(45-degree position only)

C Open

D Close

RC0030.eps

RC0031.eps

Attachment Installation

GA0005.eps

Hoist Down

Hoist Up

Tilt Forward

Tilt Back

WARNING: Truck control handle and

attachment function activation shown

here conforms to ISO 3691 recommended

practices. Failure to follow these practices

may lead to serious bodily injury or property

damage. End user, dealer and OEMs

should review any deviation from the

practices for safe operation.

6095756-R2 EN

PERIODIC MAINTENANCE

RC4854.eps

NOTE: If swing components require service, refer to

H-Series Swing Frame Paper Roll Clamp Service Manual

Supplement 6844788. If arms, clamp cylinders and rotation

related components require service, refer to H-Series

Fixed Frame Pivot Arm Paper Roll Clamp Service Manual

6078255.

Daily

Check items shown each day. Report problems to your

supervisor. See Service Manual for troubleshooting,

maintenance and repair procedures.

• Check for loose or missing bolts, worn or damaged

hoses, and hydraulic leaks.

• Check the edges of the contact pads for wear or sharp

nicks that could damage or tear paper rolls. Grind the

edges smooth.

• Check the contact pad pivot joints for wear. Repair or

replace as necessary.

• Check that load handling hydraulic system is

functioning properly. Clamp Force Indicators 830141,

832442 and 200645 are available for this test.

• Check decals and nameplate for legibility.

1000-Hour Maintenance

After each 1000 hours of truck operation, in addition to

the daily Inspection, perform the following maintenance

procedures:

• Check the torque on the stop block capscrews. Tighten

to 110 Nm, if necessary.

• Check sample of baseplate capscrews for proper

torque value. See Technical Bulletin TB183 for checking

and replacement procedures.

• Check sample of bearing capscrews for proper torque

value. See Technical Bulletin TB183 for checking and

replacement procedures.

• Tighten mounting hook capscrews:

Class II/III – 165 Nm

Class IV – 265 Nm

• Tighten rotator drive capscrews to 88 Nm.

• Lubricate rotator bearing assembly with EP-2 grease

(Whitmore 'Omnitask' or equivalent). Rotate clamp in

90 degree increments and grease in each position.

• Check rotator drive gearcase lubricant level.

Lubricant should be up to bottom of fill plug hole.

If necessary, fill with Cascade Rotator Drive Lubricant,

Part No. 656300, or SAE 90 wt. gear lube (AGMA

'mild' 6 EP Gear Oil). Replace plug.

WARNING: A sampling of faceplate and

baseplate bearing assembly capscrews

must be check for proper torque at 1000

hours (see TB183), and all capscrews

checked at every 2000 hours. Failure to

keep the capscrews tightened can result

in attachment damage and serious injury.

RC3761.eps

Contact Pad

Edges

Contact Pad

Pivot Joints

Rotator Bearing

Assembly

Grease Fitting

Rotator

Drive

Fill Plug

Arm, Cylinder, Swing,

Frame Pivot Points

Capscrew

Rotator Drive

Capscrews

Baseplate

Capscrews

Swing Frame

Pivot Joints

Baseplate

Capscrews

180-Degree

Stop Valve

Stop Block

Gear

Grease

Fitting

Mounting Hook

Capscrews

Swing Anchor

Pivot Joints

Rotator

Drive Fill

Plug

Right Side

180° Stop Valve Option

Back (Driver's) View

PERIODIC MAINTENANCE

6095756-R2 EN

2000-Hour Maintenance

After each 2000 hours of truck operation, in addition to the

daily and 1000-hour maintenance, perform the following

maintenance procedures:

• Check all rotation bearing capscrews for proper torque

value. See Technical Bulletin TB183 for checking and

replacement procedures.

• Inspect all arm and cylinder pivot pins for wear.

Replace if necessary.

4000-Hour Maintenance

After each 4000 hours of truck operation, in addition to

the daily, 1000 and 2000-hour maintenance, perform the

following maintenance procedures:

• Due to normal mechanical wear and component service

life, cylinder seals should be replaced to maintain

performance and safe operation. Refer to H-Series

Fixed Frame Pivot Arm Paper Roll Clamp Service

Manual 6078255, Section 4.4, for cylinder service.

WARNING: After completing any service

procedure, always test the attachment

through five complete cycles. First test

the attachment empty, then test with a load

to make sure the attachment operates

correctly before returning it to the job.

1000-Hour Maintenance

(continued)

• Inspect all arm, frame and cylinder pivot bushings for wear.

Replace if necessary.

• Inspect all load bearing structural welds on arms, swing

frame pivots, arm pivots and cylinder pivot areas for visual

cracks. Replace components as required.

6095756-R2 EN

123

A2-Z

Cascade Corporation • www.cascorp.com • Icons & Patents: www.cascorp.com/support 6095754

3500 lb

1586 kg

24 in

610 mm

9.1 in

220 mm

6.5 in

165 mm

1115 lb

505 kg

2300 psi

159 bar

45E–PHS–462

PTL1086133–2

6086329

2010

3500 lb

1586 kg

Legend - 30 languages (Ships with Info Group packet)

EU + China, Japan, Korean, Russian,Icelandic, Norway, Turkey

MODEL

ES MODELO IS MÓDEL MT MUDELL RU МОДЕЛЬ

BG МОДЕЛ ET MUDEL IT MODELLO NL MODEL SK MODEL

CS MODEL FI MALLI JA モデル NO MODELL SL MODEL

DA MODEL FR MODÈLE KO 모델 PL MODEL SV MODELL

DE MODELL GA DÉANAMH AGUS AINM LT MODELIS PT MODELO TR MODEL

EL ΜΟΝΤΈΛΟ HU MODELL LV MODELIS RO MODEL ZH 型号

SERIAL NUMBER

NÚMERO DE SERIE

IS RAÐNÚMER MT

NUMRU TAS-SERJE

СЕРИЙНЫЙ НОМЕР

СЕРИЕН НОМЕР

SEERIANUMBER

NUMERO DI SERIE

SERIENUMMER

SÉRIOVÉ ČÍSLO

SARJANUMERO

シリアル番号

NO SERIENUMMER SL

SERIJSKA ŠTEVILKA

SERIENUMMER

NUMERO DE SERIE

KO 일련 번호 PL

NUMER SERYJNY

SERIENUMMER

SERIENNUMMER

SRAITHUIMHIR

SERIJINIS NUMERIS

NÚMERO DE SÉRIE

TR SERI NUMARASI

ΣΕΙΡΙΑΚΟΣ ΑΡΙΘΜΟΣ

GYÁRI SZÁM

SĒRIJAS NUMURS

NUMĂR DE SERIE

序列号

EN ADDITIONAL INFORMATION ES INFORMACIÓN ADICIONAL IS VIÐBÓTARTÆKI MT INFORMAZZJONI ADDIZZJONALI RU

ДОПОЛНИТЕЛЬНАЯ ИНФОРМАЦИЯ

ДОПЪЛНИТЕЛНА ИНФОРМАЦИЯ

ET LISAINFO IT INFORMAZIONI AGGIUNTIVE NL AANVULLENDE INFORMATIE SK ĎALŠIE INFORMÁCIE

CS DOPLŇKOVÉ INFORMACE FI LISÄTIETOJA JA 追加情報 NO TILLEGGSUTSTYR SL DODATNE INFORMACIJE

DA YDERLIGERE OPLYSNINGER

INFORMATIONS SUPPLÉMENTAIRES

KO 추가 장비 PL INFORMACJE DODATKOWE SV YTTERLIGARE INFORMATION

ZUSÄTZLICHE INFORMATIONEN

GA TUILLEADH FAISNÉISE LT PAPILDOMA INFORMACIJA PT INFORMAÇÕES ADICIONAIS TR İLAVE EKIPMAN

EL ΠΡΌΣΘΕΤΕΣ ΠΛΗΡΟΦΟΡΊΕΣ HU KIEGÉSZÍTŐ INFORMÁCIÓ LV PAPILDU INFORMĀCIJA RO INFORMAŢII SUPLIMENTARE ZH 其它信息

EN MAXIMUM CAPACITY ES CAPACIDAD MÁXIMA IS HÁMARKS GETA MT KAPAĊITÀ MASSIMA RU

МАКСИМАЛЬНАЯ ГРУЗОПОДЪЕМНОСТЬ

BG МАКСИМАЛЕН КАПАЦИТЕТ ET MAKSIMAALNE JÕUDLUS IT PORTATA MASSIMA NL MAXIMAAL LAADVERMOGEN SK MAXIMÁLNA NOSNOSŤ

CS MAXIMÁLNÍ NOSNOST FI MAKSIMIKAPASITEETTI JA 最大容量 NO MAKSIMAL KAPASITET SL NAJVEČJA ZMOGLJIVOST

DA MAKS. KAPACITET FR CAPACITE MAXIMUM KO 최대 용량 PL UDŹWIG MAKSYMALNY SV MAXIMAL KAPACITET

DE MAXIMALKAPAZITÄT GA UASCHUMAS LT MAKSIMALI GALIA PT CAPACIDADE MÁXIMA

MAKSIMUM KAPASITE

EL ΜΕΓΙΣΤΗ ΧΩΡΗΤΙΚΟΤΗΤΑ HU MAXIMÁLIS KAPACITÁS LV MAKSIMĀLĀ CELTSPĒJA RO CAPACITATE MAXIMĂ ZH 最大承载能力

EN @ LOAD CENTER ES @ CENTRO DE CARGA IS @ HLEÐSLUMIÐJA MT @ ĊENTRU TAT-TAGĦBIJA RU В ЦЕНТРЕ НАГРУЗКИ

BG В ЦЕНТЪРА НА НАТОВАРВАНЕ ET @ KOORMUSE RASKUSKESE IT @ BARICENTRO DEL CARICO NL BIJ LASTZWAARTEPUNT SK V ŤAŽISKU NÁKLADU

CS @ STŘED NÁKLADU FI PAINOPISTEESSÄ JA @ 負荷の中心 NO VED LASTEPUNKT SL @ SREDIŠČE OBREMENITVE

DA VED LASTCENTRUM FR AU CENTRE DE CHARGE KO @ 하중 중심 PL @ ŚRODEK CIĘŻKOŚCI ŁADUNKU SV VID LASTENS MITTPUNKT

DE @ LASTSCHWERPUNKT GA @ LÓDPHOINTE LT TIES KROVINIO CENTRU PT @ CENTRO DE CARGA TR MAKSIMUM KAPASITE

EL ΣΤΟ ΚΕΝΤΡΟ ΒΑΡΟΥΣ HU @ TEHER KÖZEPE LV KRAVAS CENTRĀ RO LA CENTRUL DE GREUTATE ZH 载荷中心

EN MAXIMUM OPERATING PRESSURE FI MAKSIMITOIMINTAPAINE LT

MAKSIMALUS EKSPLOATACINIS SLĖGIS

МАКСИМАЛЬНОЕ РАБОЧЕЕ ДАВЛЕНИЕ

BG MАКСИМАЛНО РАБОТНО НАЛЯГАНЕ FR PRESSION DE SERVICE MAXIMALE LV MAKSIMĀLAIS DARBA SPIEDIENS SK

MAXIMÁLNY PREVÁDZKOVÝ TLAK

CS MAXIMÁLNÍ PROVOZNÍ TLAK GA UASBHRÚ OIBRIÚCHÁIN MT PRESSJONI MASSIMA TAL-OPERAT SL

NAJVEČJI DELOVNI TLAK

DA MAKSIMALT DRIFTSTRYK HU MAXIMÁLIS ÜZEMI NYOMÁS NL MAXIMUM WERKDRUK SV

MAXIMALT ARBETSTRYCK

DE MAXIMALER BETRIEBSDRUCK IS HÁMARKS VINNUÞRÝSTINGUR NO MAKSIMALT DRIFTSTRYKK TR

MAKSIMUM İŞLETME BASINCI

EL ΜΈΓΙΣΤΗ ΠΊΕΣΗ ΛΕΙΤΟΥΡΓΊΑΣ IT PRESSIONE MASSIMA DI ESERCIZIO PL MAKSYMALNE CIŚNIENIE ROBOCZE ZH

最大工作压力

ES PRESIÓN DE FUNCIONAMIENTO MÁXIMA JA 最大運転圧力 PT

PRESSÃO MÁXIMA DE FUNCIONAMENTO

ET MAKSIMAALNE TÖÖRÕHK KO 최대 작동 압력 RO PRESIUNEA DE LUCRU MAXIMĂ

MASS OF ATTACHMENT

ES PESO DEL ACCESORIO IS FJÖLDI TENGINGA MT PIŻ TAL-ATTACHMENT RU

МАССА НАВЕСНОГО ОБОРУДОВАНИЯ

МАСА НА ПРИСТАВКА

ET TÖÖSEADME MASS IT MASSA DELL’ATTREZZATURA NL

MASSA VAN VOORZETAPPARAAT

HMOTNOSŤ PRÍDAVNÉHO ZARIADENIA

HMOTNOST PŘÍDAVNÉHO ZAŘÍZENÍ

FI LISÄLAITTEEN PAINO JA 装備総量 NO MASSE FOR TILLEGGSUTSTYR SL

MASA PRIKLJUČKA

UDSTYRS VÆGT

FR MASSE DE L’ACCESSOIRE KO 부착 크기 PL MASA OSPRZĘTU SV

AGGREGATETS VIKT

ANBAUGERÄTGEWICHT

GA MAIS AN FHEISTIS LT PRIEDO MASĖ PT PESO DO ACESSÓRIO TR

EK DONANIM AĞIRLIĞI

ΜΆΖΑ ΣΥΝΔΕΔΕΜΈΝΟΥ ΕΞΟΠΛΙΣΜΟΎ

HU A SZERELÉK TÖMEGE LV UZKARES IEKĀRTAS MASA RO

MASA ECHIPAMENTULUI ATAŞAT

属具质量

NAMEPLATE ICONS

GA IDENTIFICACIÓN ICONAS NO NAVNEPLATE-IKONER

ТАБЕЛКА С ИМЕ ИКОНИ

NÉVTÁBLÁN IKONOK

NAMEPLATE ICOANE

JMENOVKA IKONY

IS NAFNASKILTATÁKN PT

IDENTIFICAÇÃO ÍCONES

NAVNESKILT IKONER

ICONE DELLA TARGA

ICONOS DE PLACA

TYPENSCHILD SYMBOLE

銘板アイコン

ТАБЛИЧКУ ЗНАЧКОВ

ΟΝΟΜΑΣΤΙΚΉΣ ΕΙΚΟΝΊΔΙΑ

KO 명판 아이콘 SK

MENOVKA ICONS

PLACA DE ICONOS

NOMINALUS PIKTOGRAMOS

TABLICA IKONE

NIMEPLAADILE IKOONID

AR NOSAUKUMU, IKONAS

NAMNSKYLTEN IKONER

NIMIKYLTTI KUVAKKEET

NAMEPLATE ICOANE

TR BILGI ETIKETI SIMGELERI

PLAQUE ICÔNES

NAAMBORD ICONEN

铭牌图标

MAXIMUM CAPACITY BETWEEN FORKS

MAKSIMINOSTOKYKY HAARUKOIDEN VÄLISSÄ

MAKSIMALI GALIA TARP ŠAKIŲ

МАКСИМАЛЬНАЯ ГРУЗОПОДЪЕМНОСТЬ

МАКСИМАЛНА ТОВАРОПОДЕМНОСТ МЕЖДУ ВИЛИЦИТЕ

CAPACITÉ MAXIMALE ENTRE LES FOURCHES

MAKSIMĀLĀ CELTSPĒJA STARP DAKŠĀM

МЕЖДУ ВИЛАМИ

MAXIMÁLNÍ NOSNOST MEZI VIDLICEMI

UASCHUMAS IDIR NA GABHAIL

KAPAĊITÀ MASSIMA BEJN IL-FRIEKET

MAXIMÁLNA NOSNOSŤ MEDZI VIDLICAMI

MAKSIMAL KAPACITET MELLEM GAFLERNE

MAXIMUM TEHERBÍRÁS VILLÁK KÖZÖTT

MAXIMUMCAPACITEIT TUSSEN VORKEN

NAJVEČJA ZMOGLJIVOST MED VILICAMI

MAXIMALE TRAGFÄHIGKEIT ZWISCHEN DEN GABELN

HÁMARKS GETA MILLI GAFLA

MAKSIMAL KAPASITET MELLOM GAFLENE

MAXIMAL KAPACITET MELLAN GAFFLAR

ΜΈΓΙΣΤΗ ΙΚΑΝΌΤΗΤΑ ΑΝΆΜΕΣΑ ΣΤΙΣ ΠΕΡΌΝΕΣ

PORTATA MASSIMA TRA LE FORCHE

MAKSYMALNY UDŹWIG POMIĘDZY WIDŁAMI

ÇATALLAR ARASI YÜK MERKEZINDEKI

CAPACIDAD MÁXIMA ENTRE HORQUILLAS

フォーク間の最大容量

CAPACIDADE MÁXIMA ENTRE GARFOS

最大承载能力

KAHVLITE VAHELINE MAX. TÕSTEVÕIME

포크 간 최대 용량

CAPACITATEA MAXIMĂ ÎNTRE FURCI

LOST LOAD CENTER DISTANCE

FAD LÓDPHOINTE CAILLTE

TAPT LASTEPUNKTAVSTAND

РАЗСТОЯНИЕ ОТ ЦЕНТЪРА НА ЗАГУБА НА НАТОВАРВАНЕ

ELVESZETT TEHERKÖZÉPPONT-TÁVOLSÁG

WIELKOŚĆ PRZESUNIĘCIA ŚRODKA CIĘŻKOŚCI ŁADUNKU

VZDÁLENOST POSUNUTÉHO STŘEDU NÁKLADU

FJARLÆGÐ GLATAÐS HLEÐSLUMIÐJU

DISTÂNCIA DO CENTRO DE CARGA PERDIDA

REDUCERET LASTCENTERAFSTAND

SPESSORE EFFETTIVO

DISTANŢA LA CENTRUL DE GREUTATE AL SARCINII

VERLORENER ABSTAND ZUM LASTMITTELPUNKT

荷重中心消失

ПОТЕРЯННОЕ РАССТОЯНИЕ ДО ЦЕНТРА НАГРУЗКИ

ΑΠΌΣΤΑΣΗ ΑΠΩΛΕΣΘΈΝΤΟΣ ΚΈΝΤΡΟΥ ΒΆΡΟΥΣ

손실 하중 중심 거리

ÚBYTOK VYLOŽENIA ŤAŽISKA S PRÍDAVNÝM ZARIADENÍM

DISTANCIA A CENTRO DE CARGA PERDIDA

ATITOLUSIO APKROVOS CENTRO ATSTUMAS

RAZDALJA DO PREMAKNJENEGA SREDIŠČA OBREMENITVE

KOORMUSE RASKUSKESKME MUUTUS

ZAUDĒTS ATTĀLUMS LĪDZ SLODZES CENTRAM

FÖRLORAT LASTMITTPUNKTSAVSTÅND

KAPASITEETIHUKAN KESKIPESTEEN ETÄISYYS

DISTANZA MIĊ-ĊENTRU TAT-TAGĦBIJA MITLUFA

KAYIP YÜK MERKEZ MESAFESI

DISTANCE CENTRE DE CHARGE PERDUE

VERLOREN AFSTAND TOT LASTZWAARTEPUNT

荷载损耗中心距离

6095756-R2 EN

EN YEAR OF MANUFACTURE

ES AÑO DE FABRICACIÓN IS FRAMLEIÐSLUÁR MT SENA TA’ MANIFATTURA RU ГОД ИЗГОТОВЛЕНИЯ

ГОДИНА НА ПРОИЗВОДСТВО

ET VALMISTAMISAASTA IT ANNO DI FABBRICAZIONE

NL BOUWJAAR SK ROK VÝROBY

CS ROK VÝROBY FI VALMISTUSVUOSI JA 製造年度 NO PRODUKSJONSÅR SL LETO IZDELAVE

DA PRODUKTIONSÅR

FR ANNÉE DE FABRICATION

KO 제조년

PL ROK PRODUKCJI

SV TILLVERKNINGSÅR

DE JAHR DER HERSTELLUNG GA BLIAIN DÉANTÚSAÍOCHTA

LT PAGAMINIMO METAI

PT ANO DE FABRICO TR ÜRETIM YILI

EL ΈΤΟΣ ΚΑΤΑΣΚΕΥΉΣ HU A GYÁRTÁS ÉVE LV RAŽOŠANAS GADS RO ANUL DE FABRICAŢIE ZH 制造年份

CAPACITY OF TRUCK AND ATTACHMENT COMBINATION MAY BE LESS THAN ATTACHMENT CAPACITY SHOWN. CONSULT TRUCK NAMEPLATE. THE CAPACITY OF THE TRUCK AND

ATTACHMENT COMBINATION SHALL BE COMPLIED WITH.

КАПАЦИТЕТЪТ НА СЪЕДИНЕНИТЕ ПОВДИГАЧ И ПРИСТАВКА МОЖЕ ДА БЪДЕ ПО-МАЛЪК ОТ ДАДЕНИЯ КАПАЦИТЕТ НА ПРИСТАВКАТА. ВИЖТЕ ТАБЕЛКАТА НА ПОВДИГАЧА.

ТОВАРОПОДЕМНОСТТА НА КАРА И КОМБИНАЦИЯТА ОТ ПРИСТАВКИ ТРЯБВА ДА СЪОТВЕТСТВАТ.

NOSNOST KOMBINACE VOZÍKU S PŘÍDAVNÝM ZAŘÍZENÍM MŮŽE BÝT MENŠÍ NEŽ UVEDENÁ NOSNOST PŘÍDAVNÉHO ZAŘÍZENÍ. PROHLÉDNĚTE SI ŠTÍTEK VOZÍKU. NOSNOST

KOMBINACE VOZÍKU A PŘÍDAVNÉHO ZAŘÍZENÍ NESMÍ BÝT PŘEKROČENA.

DEN SAMLEDE KAPACITET FOR TRUCKEN OG DET PÅMONTEREDE TILBEHØR KAN VÆRE MINDRE END DEN VISTE KAPACITET FOR TILBEHØRET. SE TRUCKENS NAVNEPLADE.

KOMBINATIONEN AF TRUCKENS KAPACITET OG TILBEHØRET SKAL OVERHOLDES.

DIE TRAGKRAFT DER KOMBINATION AUS STAPLER UND ANBAUGERÄT KANN GERINGER SEIN ALS DIE ANGEGEBENE NENNTRAGFÄHIGKEIT. SIEHE TYPENSCHILD. DIE

TRAGFÄHIGKEIT DER STAPLER-ANBAUGERÄT-KOMBINATION MUSS DAMIT ÜBEREINSTIMMEN.

Η ΧΩΡΗΤΙΚΟΤΗΤΑ ΤΟΥ ΟΧΗΜΑΤΟΣ ΚΑΙ ΣΥΝΔΥΑΣΜΟΥ ΕΞΑΡΤΗΜΑΤΩΝ ΕΝΔΕΧΕΤΑΙ ΝΑ ΕΙΝΑΙ ΧΑΜΗΛΟΤΕΡΗ ΑΠΟ ΤΗ ΧΩΡΗΤΙΚΟΤΗΤΑ ΤΟΥ ΕΞΑΡΤΗΜΑΤΟΣ ΣΤΟ ΠΑΡΑΔΕΙΓΜΑ.

ΣΥΜΒΟΥΛΕΥΤΕΙΤΕ ΤΗΝ ΕΤΙΚΕΤΑ ΟΧΗΜΑΤΟΣ. Η ΙΚΑΝΌΤΗΤΑ ΤΟΥ ΟΧΉΜΑΤΟΣ ΚΑΙ ΤΟΥ ΣΥΝΔΕΔΕΜΈΝΟΥ ΕΞΟΠΛΙΣΜΟΎ ΠΡΈΠΕΙ ΝΑ ΕΊΝΑΙ ΣΥΜΒΑΤΈΣ.

LA CAPACIDAD COMBINADA DE CARRETILLA Y ACCESORIO PUEDE SER MENOR QUE LA CAPACIDAD DEL ACCESORIO INDICADA. CONSULTE LA PLACA DE CARACTERÍSTICAS DE LA

CARRETILLA. DEBE CUMPLIRSE LA CAPACIDAD COMBINADA DE CARRETILLA Y ACCESORIO.

LAADURI JA TÖÖSEADME KOMBINATSIOONI JÕUDLUS VÕIB OLLA VÄIKSEM KUI TÖÖSEADME NÄIDATUD JÕUDLUS. VAADAKE LAADURI ANDMEPLAATI. LAADUR JA TÖÖSEADE

PEAVAD OLEMA ÜKSTEISEGA VASTAVUSES.

TRUKKI- JA LISÄLAITEYHDISTELMÄN KAPASITEETTI VOI OLLA PIENEMPI KUIN LISÄLAITTEEN ILMOITETTU KAPASITEETTI. KS. TRUKIN ARVOKILPI. TRUKIN JA LISÄLAITTEEN

YHDISTELMÄN NOSTOKYKYÄ ON NOUDATETTAVA.

LA CAPACITE DE LA COMBINAISON CHARIOT/ACCESSOIRE PEUT S’AVERER INFERIEURE A CELLE INDIQUEE POUR L’ACCESSOIRE. SE REPORTER A LA PLAQUE SIGNALETIQUE DU

CHARIOT. RESPECTER LA CAPACITÉ DU CHARIOT ET DE L’ACCESSOIRE COMBINÉS.

D’FHÉADFADH NÍOS LÚ CUMAIS A BHEITH AG AN TRUCAIL AGUS FEISTEAS NÁ AN CUMAS FEISTIS A THAISPEÁNTAR. FÉACH AR AINMCHLÁR NA TRUCAILE. CLOÍFEAR LE CUMAS NA

TRUCAILE AGUS AN CHOMHCHEANGAL FEISTIS.

A TARGONCA ÉS A TARTOZÉK KOMBINÁCIÓ KAPACITÁSA LEHET, HOGY KEVESEBB, MINT AZ ÁBRÁZOLT TARTOZÉK KAPACITÁSA. LÁSD A TARGONCA ADATTÁBLÁN. A TARGONCA ÉS

SZERELÉK KOMBINÁCIÓ TEHERBÍRÁSÁNAK ELEGET KELL TENNIE ENNEK.

GETA VÖRUBÍLS OG VIÐHENGISVIÐBÓTAR GETUR VERIÐ MINNI EN GETA VIÐHENGIS ER SÝND. RÁÐFÆRIÐ YKKUR VIÐ NAFNASKILTI VÖRUBÍLSINS. ÞAÐ Á AÐ FYLGJA GETU

VÖRUBÍLSINS OG VIÐHENGISVIÐBÓTINNI.

LA PORTATA DELLA COMBINAZIONE CARRELLO/ATTREZZATURE PUÒ ESSERE INFERIORE RISPETTO ALLA PORTATA DELLE ATTREZZATURE DICHIARATA. CONSULTARE LA

TARGHETTA DEL CARRELLO. DEVE ESSERE RISPETTATA LA PORTATA DELLA COMBINAZIONE CARRELLO ELEVATORE/ATTREZZATURA.

JA フォークリフトの能力と装備の組み合わせは示されている装備の能力より低い場合があります。フォークリフトのネームプレートを相談. トラックの容量と装備の組み合わせとは実施済み。.

KO 트럭 및 부착 결합물의 용량은 표시된 부착물 용량보다 적을 수 있습니다. 트럭 명판을 참조하십시오. 트럭 및 부착물 결합의 용량을 준수해야 합니다.

KRAUTUVO IR PRIEDO DERINIO GALINGUMAS GALI BŪTI MAŽESNIS NEGU NURODYTAS PRIEDO GALINGUMAS. SKAITYKITE INFORMACIJĄ KRAUTUVO INFORMACINĖJE PLOKŠTELĖJE.

BŪTINA NEVIRŠYTI KRAUTUVO IR PRIEDO DERINIO GALIOS.

AUTOIEKRĀVĒJA UN PIEDERUMA KOPĒJĀ CELTSPĒJA VAR BŪT MAZĀKA PAR NORĀDĪTO PIEDERUMA CELTSPĒJU. SKATĪT AUTOIEKRĀVĒJA TEHNISKO DATU PLĀKSNĪTI. IR

JĀIEVĒRO AUTOIEKRĀVĒJA UN UZKARES IEKĀRTAS KOPĒJĀ CELTSPĒJA.

IL-KAPAĊITÀ TAT-TRAKK U TAT-TAGĦMIR IMQABBAD MIEGĦU TISTA’ TKUN INQAS MILL-KAPAĊITÀ MURIJA TAT-TAGĦMIR IMQABBAD MIEGĦU. IĊĊEKKJA L-PJANĊA TAL-ISEM TAT-

TRAKK. IL-KAPAĊITÀ TAT-TRAKK FLIMKIEN MA’ DIK TAT-TAGĦMIR IMQABBAD MIEGĦU TRID TIĠI SSODISFATA.

HET DRAAGVERMOGEN VAN DE COMINATIE VAN HEFTRUCK EN VOORZETAPPARAAT KAN LAGER ZIJN DAN HET VERMELDE DRAAGVERMOGEN VAN HET VOORZETAPPARAAT. KIJK

OP HET TYPEP LAATJE VAN DE HEFTRUCK. MET DE CAPACITEIT VAN DE COMBINATIE VAN TRUCK EN VOORZETAPPARAAT WORDT REKENING GEHOUDEN.

TOTAL KOMBINERT KAPASITET FOR GAFFELTRUCK OG TILBEHØR KAN VÆRE MINDRE ENN ANGITT KAPASITET FOR TILBEHØRET. SE GAFFELTRUCKENS NAVNEPLATE. DEN TOTALE

KAPASITETEN FOR GAFFELTRUCK OG TILLEGGSUTSTYR KOMBINERT MÅ OVERHOLDES.

UDŹWIG ZESPOŁU WÓZKA I OSPRZĘTU MOŻE BYĆ MNIEJSZY NIŻ POKAZANY UDŹWIG OSPRZĘTU. PATRZ TABLICZKA ZNAMIONOWA WÓZKA. NALEŻY PRZESTRZEGAĆ

DOPUSZCZALNEGO UDŹWIGU ZESPOŁU WÓZKA I OSPRZĘTU.

A CAPACIDADE DA COMBINAÇÃO DO EMPILHADOR E DO ACESSÓRIO PODE SER INFERIOR À CAPACIDADE DO ACESSÓRIO APRESENTADA. CONSULTE A CHAPA DE

ESPECIFICAÇÕES DO EMPILHADOR. CAPACIDADE DO CAMINHÃO E COMBINAÇÃO DE PENHORA DEVE SER RESPEITADO.

CAPACITATEA VEHICULULUI ŞI A COMBINAŢIEI DISPOZITIVELOR DE PRINDERE POATE FI MAI MICĂ DECÂT CAPACITATEA DISPOZITIVELOR DE PRINDERE INDICATĂ. CONSULTAŢI

PLĂCUŢA CU CARACTERISTICILE TEHNICE ALE STIVUITORULUI. CAPACITATEA COMBINAŢIEI STIVUITOR - ECHIPAMENTE ATAŞATE TREBUIE RESPECTATĂ.

СОВМЕСТНАЯ ГРУЗОПОДЪЕМНОСТЬ АВТОПОГРУЗЧИКА И НАВЕСНОГО УСТРОЙСТВА МОЖЕТ БЫТЬ НИЖЕ УКАЗАННОЙ ГРУЗОПОДЪЕМНОСТИ НАВЕСНОГО УСТРОЙСТВА. СМ.

ТАБЛИЧКУ ТЕХНИЧЕСКИХ ДАННЫХ. НЕОБХОДИМО СОБЛЮДАТЬ КОМБИНИРОВАННУЮ ГРУЗОПОДЪЕМНОСТЬ АВТОПОГРУЗЧИКА И НАВЕСНОГО ОБОРУДОВАНИЯ.

NOSNOSŤ VOZÍKA A PRÍDAVNÉHO ZARIADENIA MÔŽE BYŤ MENŠIA AKO UVEDENÁ NOSNOSŤ PRÍDAVNÉHO ZARIADENIA. BLIŽŠIE INFORMÁCIE UVEDENÉ NA TYPOVOM ŠTÍTKU

VOZÍKA. NOSNOSŤ VOZÍKA S PRÍDAVNÝM ZARIADENÍM BUDE DODRŽANÁ.

ZMOGLJIVOST KOMBINACIJE VILIČARJA IN OPREME JE LAHKO MANJŠA OD PRIKAZANE ZMOGLJIVOSTI OPREME. UPOŠTEVAJTE NAPISNO PLOŠČICO VILIČARJA. UPOŠTEVATI JE

POTREBNO ZMOGLJIVOST KOMBINACIJE VILIČARJA IN OPREME.

KAPACITETEN FÖR KOMBINATIONEN GAFFELTRUCK OCH AGGREGAT KAN VARA MINDRE ÄN ANGIVEN KAPACITET. LÄS GAFFELTRUCKENS TYPSKYLT. KAPACITETEN FÖR

KOMBINATIONEN GAFFELTRUCK OCH AGGREGAT SKA FÖLJAS.

ARAÇ KAPASITESI VE DONANIM KOMBINASYONU, GÖSTERILEN DONANIM KAPASITESINDEN DÜŞÜK OLABILIR. ARAÇ BILGI ETIKETINE BAŞVURUN. ARAÇ KAPASITESI VE DONANIM

KOMBINASYONU UYUMLU OLMALIDIR.

ZH 叉车与叉车属具的综合承载能力可能小于显示的叉车属具承载能力。请参考叉车铭牌。应符合叉车与叉车属具的综合承载能力。

CENTER OF GRAVITY TO MOUNT FACE DISTANCE

FAD IDIR AN MEÁCHANLÁR AGUS AN ÉADAN FEISTE

AVSTAND TYNGDEPUNKT TIL MONTERINGSFLATE

ЦЕНТЪР НА ТЕЖЕСТТА СПРЯМО РАЗСТОЯНИЕТО ОТ МОНТАЖНАТА ЧЕЛНА ПОВЪРХНИНА

SÚLYPONT - SZERELŐFELÜLET TÁVOLSÁG

ODLEGŁOŚĆ OD ŚRODKA CIĘŻKOŚCI DO CZOŁA ZAWIESZENIA

VZDÁLENOST STŘEDU NÁKLADU K ČELU RÁMU

MIÐJA ÞYNGDARAFLS TIL AÐ HLAÐA ÚR LÍKAMSFJARLÆGÐ

DISTÂNCIA DO CENTRO DE GRAVIDADE À SUPERFÍCIE DE MONTAGEM

AFSTANDEN MELLEM TYNGDEPUNKT OG MONTERINGSFLADEN

CENTRO DI GRAVITA’ DAL PIANO DI AGGANCIO

DISTANŢA DE LA CENTRUL DE GREUTATE LA SUPRAFAŢA DE MONTARE

ABSTAND ZWISCHEN SCHWERPUNKT UND MONTAGEFLÄCHE

マウント面への重心

РАССТОЯНИЕ ОТ ЦЕНТРА ТЯЖЕСТИ ДО УСТАНОВОЧНОЙ ПОВЕРХНОСТИ

ΑΠΌΣΤΑΣΗ ΚΈΝΤΡΟΥ ΒΆΡΟΥΣ ΑΠΌ ΤΗΝ ΠΡΌΣΟΨΗ ΒΆΣΗΣ

장착 면 거리에 대한 중력 중심

VZDIALENOSŤ ŤAŽISKA OD ČELNEJ STRANY UCHYTENIA

DISTANCIA DE CENTRO DE GRAVEDAD A CARA DE MONTAJE

ATSTUMAS NUO SUNKIO JĖGOS CENTRO IKI PAGRINDO PRIEKINĖS

PUSĖS

RAZDALJA TEŽIŠČA OD SPREDNJE MONTAŽNE STRANI

RASKUSKESKME KAUGUS EESMISEST KINNITUSPINNAST

ATTĀLUMS NO SMAGUMA CENTRA LĪDZ UZSTĀDĪŠANAS VIRSMAI

AVSTÅND TYNGDPUNKT TILL MONTERINGSYTA

PAINOPISTEEN ETÄISYYS KIINNITYSPINNASTA

ĊENTRU TA’ GRAVITÀ SAD-DISTANZA MOUNT FACE

AĞIRLIK MERKEZI ILE FORK YÜZÜ ARASI MESAFE

DISTANCE CENTRE DE GRAVITÉ-FACE DE MONTAGE

AFSTAND TUSSEN ZWAARTEPUNT EN MONTAGEVLAK

重心到安装面的距离

Leht laadib ...

Cascade 10H Original Instructions Manual

Bränd: Cascade

Mudel: 10H

Tüüp: Original Instructions Manual

Laadige alla PDF

aruanne

teistes keeltes

English: Cascade 10H

Cascade 10H Original Instructions Manual

Cascade 10H Original Instructions Manual

teistes keeltes

Muud dokumendid