Sonicare HX6971/33 Kasutusjuhend

FlexCare Platinum

4235_020_9771_1_Book_Simp_A6_v1.indd 1 14/04/15 10:40

2

1

3

4

5

6

8

9

10

7

11

12

13

1

English 6

Čeština 21

Eesti 37

Hrvatski 52

Latviešu 68

Lietuviškai 83

Magyar 99

Polski 115

Română 133

Slovenščina 150

Slovensky 165

Български 181

English

Introduction

Congratulations on your purchase and welcome to Philips! To fully

benefit from the support that Philips offers, register your product at

www.philips.com/welcome.

Important

Read this user manual carefully before you use the appliance and

save it for future reference.

-

Keep the charger away from water. Do not

place or store it over or near water

contained in a bathtub, washbasin, sink etc.

Do not immerse the charger in water or any

other liquid. After cleaning, make sure the

charger is completely dry before you

connect it to the mains.

Warning

-

The mains cord cannot be replaced. If the

mains cord is damaged, discard the charger.

-

Always have the charger replaced with one

of the original type in order to avoid a

hazard.

-

Do not use the charger outdoors or near

heated surfaces.

6

English

-

If the appliance is damaged in any way

(brush head, toothbrush handle or charger),

stop using it. This appliance contains no

serviceable parts. If the appliance is

damaged, contact the Consumer Care

Centre in your country (see chapter

‘Guarantee and support').

-

This appliance can be used by children

aged from 8 years and above and persons

with reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved. Children shall not play

with the appliance. Cleaning and user

maintenance shall not be made by children

unless they are older than 8 and supervised.

Caution

-

Do not clean the brush head, the handle,

the charger, the charger cover and/or the

sanitiser in the dishwasher.

7

English

-

If you have had oral or gum surgery in the

previous 2 months, consult your dentist

before you use the toothbrush.

-

Consult your dentist if excessive bleeding

occurs after using this toothbrush or if

bleeding continues to occur after 1 week of

use.Also consult your dentist if you

experience discomfort or pain when you use

the Sonicare.

-

The Sonicare toothbrush complies with the

safety standards for electromagnetic

devices. If you have a pacemaker or other

implanted device, contact your physician or

the device manufacturer of the implanted

device prior to use.

-

If you have medical concerns, consult your

doctor before you use the Sonicare.

-

This appliance has only been designed for

cleaning teeth, gums and tongue. Do not

use it for any other purpose. Stop using the

appliance and contact your doctor if you

experience any discomfort or pain.

8

English

-

The Sonicare toothbrush is a personal care

device and is not intended for use on

multiple patients in a dental practice or

institution.

-

Stop using a brush head with crushed or

bent bristles. Replace the brush head every

3 months or sooner if signs of wear appear.

-

Do not use other brush heads than the ones

recommended by the manufacturer.

-

If your toothpaste contains peroxide, baking

soda or bicarbonate (common in whitening

toothpastes), thoroughly clean the brush

head with soap and water after each

use.This prevents possible cracking of the

plastic.

-

Do not insert objects into the air openings of

the sanitiser or block these air openings by

placing it on a soft surface or in a position or

location where objects will block these

openings (examples of objects:

-

magazine, tissue paper and hair).

9

English

-

The UV light bulb is hot during and

immediately after the sanitising cycle. Do

not touch the UV light bulb when it is hot.

-

Do not operate the sanitiser without the

protective screen in place to avoid contact

with a hot bulb.

-

If the sanitiser has been used for 3

consecutive UV clean cycles (i.e. 3 times in a

row), switch it off for at least 30 minutes

before you start another UV clean cycle.

-

Discontinue use of the sanitiser if the UV

light bulb remains on when the door is

open. UV light can be harmful to the human

eye and skin. Keep the sanitiser out of the

reach of children at all times.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and

regulations regarding exposure to electromagnetic fields.

General description (Fig. 1)

1 Hygienic travel cap

2 Brush head with unique identifier

3 Handle

4 Power on/off button

5 Intensity level indicator

6 Intensity level button (+ and -)

7 Brushing modes

10

English

8 Mode button

9 Battery level indicator

10 UV sanitiser base with integrated charger and cord wrap (specific

types only)

- Not shown: UV light bulb

- Not shown: Sanitizer drip tray

- Not shown: Protective screen for UV light bulb

11 Mains cord with plug

12 Charger cover with brush head holders (select models)

13 Travel charger

- Not shown: Travel case

The content of the box may vary based on the model purchased.

Preparing for use

Attaching the brush head

1 Align the brush head so the bristles point in the same direction as

the front of the handle.

2 Firmly press the brush head down onto the metal shaft until it

stops.

Philips Sonicare brush heads are imprinted with icons to easily

identify your brush head.

Charging the appliance

1 Put the plug of the charger or sanitizer in a wall socket.

2 Place the handle on the charger.

The flashing light of the battery level indicator indicates that the

toothbrush is charging.

Note: It takes at least 24 hours to fully charge the battery.

Using the appliance

Brushing instructions

1 Wet the bristles (Fig. 4) and apply a small amount of toothpaste

(Fig. 5). (Fig. 4)

11

English

2 Place the toothbrush bristles against the teeth at a slight angle (45

degrees), pressing firmly to make the bristles reach the gumline or

slightly beneath the gumline. A change in vibration (and a slight

change in sound) alerts you when you apply too much pressure

while brushing. (Fig. 6)

Note: Keep the center of the brush in contact with the teeth at all

times.

3 Press the power on/off button to switch on the Philips Sonicare.

(Fig. 7)

4 Apply light pressure to maximize Philips Sonicare’s effectiveness

and let the Philips Sonicare toothbrush do the brushing for you. Do

not scrub.

5 Gently move the brush head slowly across the teeth in a small

back and forth motion so the longer bristles reach between your

teeth (Fig. 8). Continue this motion throughout the brushing cycle.

6 To clean the inside surfaces of the front teeth, tilt the brush handle

semi-upright and make several vertical overlapping brushing

strokes on each tooth (Fig. 9).

7 Begin brushing in section 1 (outside upper teeth) and brush for 30

seconds (45 seconds in Deep Clean mode) before you move to

section 2 (inside upper teeth). Continue brushing in section 3

(outside lower teeth) and brush for 30 seconds (45 seconds in

Deep Clean mode) before you move to section 4 (inside lower

teeth (Fig. 10)).

Note: To make sure you brush evenly throughout the mouth, divide

your mouth into 4 sections using the Quadpacer feature (see chapter

‘Features’).

Note:After you have completed the brushing cycle, you can spend

additional time brushing the chewing surfaces of your teeth and areas

where staining occurs. (Fig. 11) You can also brush your tongue, with

the toothbrush turned on or off, as you prefer.

Your Philips Sonicare is safe to use on:

- Braces (brush heads wear out sooner when used on braces).

- Dental restorations (fillings, crowns, veneers).

12

English

Brushing modes

Clean mode

For an exceptional everyday clean (default mode).

White mode

2 minutes to remove surface stains and 30 seconds to brighten and

polish your front teeth.

Deep Clean

Provides an invigorating 3 minutes of alternating cleaning and

massaging to deliver an exceptionally clean experience.

Your Philips Sonicare comes with the Clean mode activated.

Note: When the toothbrush is switched on, you cannot toggle

between modes.

1 Before you switch on the Philips Sonicare, press the mode button

to toggle between modes.

-

The selected brushing mode lights up.

-

Once a brushing mode has been selected, it remains active until

another brushing mode is selected.

Note: When the Philips Sonicare is used in clinical studies, it must be

used in the default 2-minute Clean mode at high intensity or in the

Deep Clean mode at high intensity.

Intensity levels per mode

- Low: 1 LED indicator light.

- Medium: 2 LED indicator lights.

- High: 3 LED indicator lights.

Note: to adjust the intensity level to the next higher or lower level,

you can press the + button to increase intensity or the - button to

decrease intensity at any time during the brushing cycle.

Pressure Sensor

A change in vibration (and a slight change in sound) alerts you when

you apply too much pressure while brushing. See chapter ‘Features’.

Battery status (when handle is not on charger)

- 1 yellow LED indicates a low charge.

13

English

- 3 green LEDs indicate a full charge.

Note: If you hear a long beep and the yellow LED of the battery level

indicator flashes, your toothbrush is completely empty and switches

off. Place the toothbrush on the charger to recharge it.

Note: To keep the battery fully charged at all times, you may keep

your Philips Sonicare on the charger when not in use.

Features

Pressure Sensor

This Philips Sonicare model comes with the Pressure Sensor feature

activated. The Pressure Sensor works in all 3 modes and at all 3

intensity levels.

Activating or deactivating the Pressure Sensor feature

1 Attach the brush head to the handle.

2 Place the handle in the plugged-in charger or sanitizer.

- To deactivate Pressure Sensor:

Press and hold the power on/off and mode button for 2 seconds.

You hear 1 beep to indicate that the Pressure Sensor feature has

been deactivated.

- To activate Pressure Sensor:

Press and hold the power on/off and mode button for 2 seconds.

You hear 2 beeps to indicate that the Pressure Sensor feature has

been activated.

Quadpacer

- The Quadpacer is an interval timer that has a short beep and

pause to remind you to brush the 4 sections of your mouth.

Depending on the brushing mode or brushing routine you have

selected, the Quadpacer beeps at different intervals during the

brushing cycle. The Quadpacer works in all 3 modes and at all 3

intensity levels. (Fig. 10)

The Quadpacer feature on this model has been activated. To

deactivate or reactivate the Quadpacer feature:

1 Place the handle in the plugged-in charger. or sanizater.

2 Press and hold the mode button until:

14

English

a You hear 1 beep to indicate that the Quadpacer has been

deactivated.

b You hear 2 beeps to indicate that the Quadpacer has been

activated.

Smartimer

The Smartimer indicates that your brushing cycle is complete by

automatically turning off the toothbrush at the end of the brushing

cycle.

Dental professionals recommend brushing no less than 2 minutes

twice a day.

Easy-start

This Sonicare comes with the Easy-start deactivated.

The Easy-start feature gently increases the power over the first 14

brushings to help you get used to the brushing with the Philips

Sonicare.

Note: Each of the first 14 brushings must be at least 1 minute in length

to properly advance through the Easy-start ramp-up cycle.

Activating or deactivating the Easy-start feature

1 Attach the brush head to the handle.

2 Place the handle in the plugged-in charger or sanitizer.

- To activate Easy-start:

Press and hold the power on/off button for 2 seconds. You hear 2

beeps to indicate that the Easy-start feature has been activated.

- To deactivate Easy-start:

Press and hold the power on/off button for 2 seconds. You hear 1

beep to indicate that the Easy-start feature has been deactivated.

Note: Using the Easy-start feature beyond the initial ramp-up period

is not recommended and reduces Philips Sonicare effectiveness in

removing plaque.

Note: Each of the first 14 brushings must be at least 1 minute in length

to properly move through the Easy-start ramp-up cycle.

15

English

Sanitizing

- With the UV sanitizer you can clean your brush head after every

use (Fig. 12).

Unplug the sanitizer, discontinue use and call Consumer Care if:

- The UV light bulb remains on when the door is open.

- The window is broken or missing from the sanitizer.

- The sanitizer gives off smoke or a burning smell while it is

operating.

Note: UV light can be harmful to the human eye and skin. This device

should be kept out of reach of children at all times.

1 After brushing, rinse the brush head and shake off excess water.

Warning: Do not place the travel cap on the brush head

during sanitization.

2 Place your finger in the door recess on top of the sanitizer and pull

open the door (Fig. 13).

3 Place the brush head on one of the 2 pegs in the sanitizer with the

bristles facing the light bulb (Fig. 14).

Note: Only clean Philips Sonicare snap-on brush heads in the

sanitizer.

Note: Do not clean Philips Sonicare for Kids brush heads in the

sanitiser.

4 Make sure the sanitizer is plugged into a live outlet of appropriate

voltage.

5 Close the door and press the green power on/off button once to

select the UV clean cycle.

Note: You can only turn on the sanitizer if the door is properly

closed.

Note: The sanitizer stops if you open the door during the sanitizing

cycle.

Note: The sanitizer cycle runs for 10 minutes and then

automatically shuts off.

-

The sanitizer is in operation when the light glows through the

window.

16

English

Cleaning

Warning: Do not clean the brush head, handle, travel

charger or the UV sanitizer in the dishwasher.

Toothbrush handle

1 Remove the brush head and rinse the metal shaft area with warm

water. Make sure you remove any residual toothpaste (Fig. 15).

Caution: Do not push on the rubber seal on the metal shaft with

sharp objects, as this may cause damage.

2 Wipe the entire surface of the handle with a damp cloth.

Brush head

1 Rinse the brush head and bristles after each use (Fig. 16).

2 Remove the brush head from the handle and rinse the brush head

connection with warm water at least once a week.

Sanitizer

Warning: Do not immerse the sanitizer in water or rinse it

under the faucet.

Warning: Do not clean the sanitizer when the UV light bulb

is hot.

For optimal effectiveness, it is recommended to clean your sanitizer

weekly.

1 Unplug the sanitizer.

2 Pull the drip tray straight out. Rinse the drip tray and wipe it clean

with a damp cloth (Fig. 17).

3 Clean all interior surfaces with a damp cloth.

4 Remove the protective screen in front of the UV light bulb (Fig. 18).

To remove the screen, grasp the edges next to the snaps, gently

squeeze and pull out the protective screen.

5 Remove the UV light bulb.

To remove the light bulb, grasp it and pull it out of the metal clasp.

17

English

6 Clean the protective screen and the UV light bulb with a damp

cloth.

7 Reinsert the UV light bulb.

To reinsert the light bulb, align the bottom of the light bulb with

the metal clasp and push the bulb into the clasp.

8 Reinsert the protective screen.

To reinsert the screen, align the pegs on the screen with the slots

on the reflective surface near the UV light bulb. Push the screen

straight into the slots on the sanitizer.

Storage

If you are not going to use the product for a long time, unplug it, clean

it (see chapter 'Cleaning') and store it in a cool and dry place away

from direct sunlight. You can use the integrated cord wrap to store

excess cord of the UV sanitizer in an organized manner.

Replacement

Brush head

- Replace Philips Sonicare brush heads every 3 months to achieve

optimal results.

- Use only Philips Sonicare replacement brush heads.

Ordering accessories

To buy accessories or spare parts, visit

www.shop.philips.com/service or go to your Philips dealer. You can

also contact the Philips Consumer Care Center in your country (see

the international warranty leaflet for contact details).

Recycling

- This symbol means that this product shall not be disposed of with

normal household waste (2012/19/EU).

18

English

- This symbol means that the product contains a built-in

rechargeable battery covered by European Directive

2006/66/EC, which cannot be disposed of with normal household

waste. The chemical symbol 'Hg' shown below the wheeled bin

means that the rechargeable battery contains mercury. Follow the

instructions in section ‘Removing the rechargeable battery’ to

remove the battery.

- Follow your country's rules for the separate collection of electrical

and electronic products and batteries. Correct disposal helps

prevent negative consequences for the environment and human

health.

Removing disposable batteries

To remove disposable batteries, see the instructions for placing

and/or removing batteries in the user manual.

Removing the rechargeable battery

Warning: PLEASE NOTE THAT THIS PROCESS IS NOT

REVERSIBLE.

- To remove the rechargeable battery, you need a flat-head

(standard) screwdriver. Observe basic safety precautions when

you follow the procedure outlined below. Be sure to protect your

eyes, hands, fingers, and the surface on which you work.

1 To deplete the rechargeable battery of any charge, remove the

handle from the charger, turn on the Philips Sonicare and let it run

until it stops. Repeat this step until you can no longer switch on

the Philips Sonicare.

2 Insert a screwdriver into the slot located at the bottom of the

handle and turn counterclockwise to release the bottom cap (Fig.

19).

19

English

3 Hold the handle upside down and push down on the shaft to

release the internal components of the handle (Fig. 20).

4 Insert the screwdriver under the circuit board, next to the battery

connections, and twist to break the connections. Remove the

circuit board and pry the battery from the plastic carrier (Fig. 21).

The rechargeable battery can now be recycled and the rest of the

product discarded appropriately.

Guarantee and support

If you need information or support, please visit

www.philips.com/support or read the separate worldwide guarantee

leaflet.

The terms of the international warranty do not cover the following:

- Brush heads.

- Damage caused by use of unauthorized replacement parts.

- Damage caused by misuse, abuse, neglect, alterations or

unauthorized repair.

- Normal wear and tear, including chips, scratches, abrasions,

discoloration or fading.

- UV light bulb.

20

English

Leht laaditakse ...

Sonicare HX6971/33 Kasutusjuhend

Sonicare HX6971/33 Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid