Ransomes 62304, 62379 Omaniku manuaal

Bränd: Ransomes

Mudel: 62304, 62379

Kategooria: Muruniidukid

Tüüp: Omaniku manuaal

Safety, Operation, & Maintenance Manual

WARNING

Warning: If incorrectly used, this machine can

cause severe injury. Those who use and maintain

this machine should be trained in its proper use,

warned of its dangers, and must read the entire

manual before attempting to set up, operate, adjust,

or service the machine.

Greens King IV Plus with ROPS

62304 – Kubota D722-E3B Engine

62379 – Kubota D722-E4B Engine

4212747-Rev B

This manual contains safety and operating instructions

for your new Jacobsen machine. This manual should be

stored with the equipment for reference during operation.

Before you operate your machine, you and each operator

you employ should read the manual carefully in its

entirety. By following the safety, operating, and

maintenance instructions, you will prolong the life of your

equipment, and maintain its maximum efficiency.

If additional information is needed, contact your

Jacobsen Dealer.

The serial plate is attached to the frame, near the battery.

Jacobsen recommends you record these numbers below

for easy reference.

11524 WILMAR BLVD,

CHARLOTTE, NC 28273

kg kW

1-800-848-1636 (US)

PRODUCT OF U.S.A.

A Textron Company

FOREWORD

1 CONTENTS

reserved, including the right to reproduce this material or portions

thereof in any form.”

Proposition 65 Warning

This product contains or emits

chemicals known to the State of

California to cause cancer and birth

defects or other reproductive harm.

Litho In U.S.A. 2-2014

CONTENTS 1

1CONTENTS

2SAFETY

2.1 Operating Safety.................................................. 4

2.2 Important Safety Notes ........................................ 5

3 SPECIFICATIONS

3.1 Product Identification ........................................... 6

3.2 Engine ................................................................. 6

3.3 Cutting Units ........................................................ 6

3.4 Mower .................................................................. 7

3.5 Weights and Dimensions ..................................... 7

3.6 Accessories & Support Literature ........................ 7

3.7 Declaration of Conformity .................................... 8

4DECALS

4.1 Decals................................................................ 10

5 CONTROLS

5.1 Icons .................................................................. 15

5.2 Control Descriptions .......................................... 17

6 OPERATION

6.1 Daily Inspection ................................................. 18

6.2 Interlock System ................................................ 18

6.3 Operating Procedures ....................................... 19

6.4 Starting .............................................................. 20

6.5 Stopping / Parking ............................................. 20

6.6 To Drive / Transport ........................................... 21

6.7 Hillside Operation .............................................. 21

6.8 Mowing .............................................................. 23

6.9 Towing / Trailering ............................................. 24

6.10 Daily maintenance ............................................. 25

7 MAINTENANCE & LUBRICATION CHARTS

7.1 General.............................................................. 26

7.2 Lubrication Chart ............................................... 26

7.3 Maintenance Charts .......................................... 27

8 MAINTENANCE

8.1 General.............................................................. 28

8.2 Engine ............................................................... 28

8.3 Engine Oil .......................................................... 29

8.4 Diesel Air Filter .................................................. 29

8.5 Fuel .................................................................... 30

8.6 Fuel System ....................................................... 30

8.7 Battery ............................................................... 30

8.8 Jump Starting .................................................... 31

8.9 Charging Battery ................................................ 31

8.10 Hydraulic Hoses ................................................ 32

8.11 Hydraulic Oil ...................................................... 32

8.12 Hydraulic Oil Filters ........................................... 33

8.13 Electrical System ............................................... 33

8.14 Muffler And Exhaust .......................................... 33

8.15 Tires ................................................................... 33

8.16 Wheel Mounting Procedure ............................... 34

8.17 Roll Over Protective Structure (ROPS) ............. 34

8.18 Care And Cleaning ............................................ 34

8.19 Radiator ............................................................. 35

8.20 Backlapping ....................................................... 35

8.21 Grinding Bedknife .............................................. 36

8.22 Storage .............................................................. 36

9ADJUSTMENTS

9.1 General.............................................................. 37

9.2 Bedknife-To-Reel ............................................... 37

9.3 Bedknife Adjustment .......................................... 38

9.4 Cutting Height .................................................... 38

9.5 Bedknife Adjuster Spring ................................... 39

9.6 Bedknife Adjuster Tension ................................. 39

9.7 Antisway Spring ................................................. 39

9.8 Accelerator Pedal .............................................. 40

9.9 Brake Pedal ....................................................... 40

9.10 Parking Brake .................................................... 40

9.11 Interlock Switches .............................................. 41

9.12 Traction Lever .................................................... 41

9.13 Reel Control ....................................................... 41

9.14 Reel Switches .................................................... 42

9.15 Leveling Procedure ............................................ 42

9.16 Reel Bearing ...................................................... 42

9.17 Fan Belt ............................................................. 43

9.18 Lift Cylinders ...................................................... 43

9.19 Specific Torque Requirements .......................... 43

9.20 Torque Specification .......................................... 44

10 PROBLEM SOLVING

10.1 General .............................................................. 45

11 QUALITY OF CUT

11.1 Quality Of Cut Troubleshooting ......................... 46

11.2 Washboarding .................................................... 46

11.3 Marcelling .......................................................... 47

11.4 Step Cutting ....................................................... 48

11.5 Scalping ............................................................. 49

11.6 Stragglers .......................................................... 50

11.7 Streaks............................................................... 51

11.8 Windrowing ........................................................ 52

11.9 Rifling Or Tramlining .......................................... 53

11.10 Mismatched Cutting Units .................................. 53

2 SAFETY

2.1 OPERATING SAFETY ______________________________________________________

1. Safety is dependent upon the awareness, concern

and prudence of those who operate or service the

equipment. Never allow minors to operate any

equipment.

2. It is your responsibility to read this manual and all

publications associated with this equipment (Safety

& Operation Manual, Engine Manual, and

attachments/accessories instruction sheets). If the

operator cannot read English it is the owner’s

responsibility to explain the material contained in

this manual to them.

3. Learn the proper use of the machine, the location

and purpose of all the controls and gauges before

you operate the equipment. Working with unfamiliar

equipment can lead to accidents.

4. Never allow anyone to operate or service the

machine or its attachments without proper training

and instructions; or while under the influence of

alcohol or drugs.

5. Wear all the necessary protective clothing and

personal safety devices to protect your head, eyes,

ears, hands, and feet. Operate the machine only in

daylight or in good artificial light.

6. Evaluate the terrain to determine what accessories

and attachments are needed to properly and safely

perform the job. Only use accessories and

attachments approved by Jacobsen.

7. Stay alert for holes in the terrain and other hidden

hazards.

8. Inspect the area where the equipment will be used.

Pick up all the debris you can find before operating.

Beware of overhead obstructions (low tree limbs,

electrical wires, etc.) and also underground

obstacles (sprinklers, pipes, tree roots, etc.). Enter a

new area cautiously. Stay alert for hidden hazards.

9. Never direct discharge of material toward

bystanders, nor allow anyone near the machine

while in operation. The owner/operator can prevent

and is responsible for injuries inflicted to

themselves, to bystanders, and damage to property.

10. Do not carry passengers. Keep bystanders and pets

a safe distance away.

11. Never operate equipment that is not in perfect

working order or is without decals, guards, shields,

discharge deflectors, or other protective devices

securely fastened in place.

12. Never disconnect or bypass any switch.

13. Do not change the engine governor setting or

overspeed the engine.

14. Carbon monoxide in the exhaust fumes can be fatal

when inhaled. Never operate the engine without

proper ventilation or in an enclosed area.

15. Fuel is highly flammable; handle with care.

16. Keep the engine clean. Allow the engine to cool

before storing and always remove the ignition key.

17. Disengage all drives and engage parking brake

before starting the engine (motor). Start the engine

only when sitting in operator’s seat, never while

standing beside the unit.

18. Equipment must comply with the latest federal,

state, and local requirements when driven or

transported on public roads. Watch out for traffic

when crossing or operating on or near roads.

19. Local regulations may restrict the age of the

operator.

20. Never use your hands to search for oil leaks.

Hydraulic fluid under pressure can penetrate the

skin and cause serious injury.

21. Operate the machine up and down the face of

slopes (vertically), not across the face (horizontally).

22. To prevent tipping or loss of control, do not start or

stop suddenly on slopes. Reduce speed when

making sharp turns. Use caution when changing

directions.

23. Always use the seat belt when operating mowers

equipped with a Roll Over Protective Structure

(ROPS).

Never use a seat belt when operating mowers

without a ROPS.

24. Always disconnect battery cables from battery

before performing any welding operation on the

mower.

This machine is to be operated and maintained as specified in this manual and is intended for the professional

maintenance of specialized turf grasses. It is not intended for use on rough terrain or long grasses.

WARNING

EQUIPMENT OPERATED IMPROPERLY OR BY UNTRAINED PERSONNEL CAN BE DANGEROUS.

Familiarize yourself with the location and proper use of all controls. Inexperienced operators should receive

instruction from someone familiar with the equipment before being allowed to operate the machine.

SAFETY 2

2.2 IMPORTANT SAFETY NOTES ________________________________________________

This safety alert symbol is used to alert you to potential hazards.

DANGER - Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

WARNING - Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious

injury.

CAUTION - Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury

and property damage. It may also be used to alert against unsafe practices.

NOTICE - Indicates a potentially hazardous situation which, if not avoided, MAY result in property damage. It may

also be used to alert against unsafe practices.

For pictorial clarity, some illustrations in this manual may show shields, guards or plates open, or removed. Under no

circumstances should this equipment be operated without these devices securely fastened in place.

By following all instructions in this manual, you will prolong the life of your machine and maintain its maximum

efficiency. Adjustments and maintenance should always be performed by a qualified technician.

If additional information or service is needed, contact your Authorized Jacobsen Dealer who is kept informed of the

latest methods to service this equipment and can provide prompt and efficient service.

WARNING

The Interlock System on this mower prevents the mower from starting unless

the parking brake is engaged, reel levers are off, and traction lever is in

Neutral. The system will stop the engine if the operator leaves the seat

without engaging the parking brake, setting the reel levers to off, and placing

traction lever in Neutral.

NEVER operate mower unless the Interlock System is working.

WARNING

1. Before leaving the operator’s position for any reason:

a. Return traction lever to Neutral.

b. Disengage all drives.

c. Lower all implements to the ground.

d. Engage parking brake.

e. Stop engine and remove the ignition key.

2. Keep hands, feet, and clothing away from moving parts. Wait for all

movement to stop before you clean, adjust, or service the machine.

3. Keep the area of operation clear of all bystanders and pets.

4. Never carry passengers.

3 SPECIFICATIONS

3 SPECIFICATION S

3.1 PRODUCT IDENTIFICATION _________________________________________________

62304.............................. Greens King IV Plus, 17.7 hp

diesel engine, power steering.

Without reels.

62379.............................. Greens King IV Plus, 17.7 hp

diesel engine, power steering.

Without reels.

Serial Number ................ An identification plate, like the one

shown, listing the serial number, is

attached to the frame of the

mower near the battery.

Always provide the serial number of the unit when ordering

replacement parts or requesting service information.

3.2 ENGINE__________________________________________________________________

Make ............................... Kubota

Model .............................. D722-E3B (62304)

Model .............................. D722-E4B (62379)

Horsepower..................... 17.7 hp (13.2 kW) @3200 rpm

Displacement .................. 40.03 cu. In. (719 cc)

Torque............................. 26 ft. lbs. (35 Nm) @ 2600 rpm

Fuel:

Type .......................... No. 2 Low or Ultra Low Sulfur

Diesel

Rating ....................... Min. Cetane rating 45

Capacity.................... 5 U.S. Gal. (18.9 liters)

Governor......................... Ball Type Governor

Low Idle ................... 1100 RPM

High Idle ................... 3400 RPM

Lubrication:

Capacity.................... 3.4 quarts (3.2 liter) with filter

Type .......................... SAE 20W, SAE 30W

API Classification ..... CD, CE

Air Filter .......................... Dry type with evacuator valve and

service indicator.

Alternator ........................ 14 amp

Cooling System .............. Liquid Cooled

Capacity...................... 3qt. (2.8 l) 50/50 water ethylene

glycol mix

3.3 CUTTING UNITS___________________________________________________________

Reel ................................ 3 Reels, 22 in. (559 mm) wide.

Reel Diameter................. 5 in. (127 mm)

Blade Options ................. 7, 9 or 11 blades

Cutting Width .................. 62 in. (1574 mm)

Cutting Frequency:

7 Blade ..................... 0.084 in./mph (1.33 mm/kph)

9 Blade ..................... 0.065 in./mph (1.03 mm/kph)

11 Blade ................... 0.053 in./mph (0.84 mm/kph)

15 Blade ................... 0.039 in./mph (0.61 mm/kph)

Product

EEC Sound

Power

Sound Pressure

Level

Operator Ear

Vibration M/S

Arms Body

62379 102 dBa 87 dBa 2.03 0.52

11524 WILMAR BLVD,

CHARLOTTE, NC 28273

kg kW

1-800-848-1636 (US)

PRODUCT OF U.S.A.

A Textron Company

587 13.2 XXXX

62379001651

SPECIFICATIONS 3

3.4 MOWER__________________________________________________________________

Tires ................................ 18 x 9.5 - 8 tubeless

Tire Pressure:

Front.......................... 10-12 psi (0.69-0.83 BAR)

Rear ..........................8-10 psi (0.55-0.69 BAR)

Battery:

Type ..........................12 Volt Lead/Acid

Group ........................22 GMF

Parking Brake.................. Mechanical front drum brakes

Hand lever actuated

Speed:

Mow ......................... 0 - 3.7 mph (5.9 kph)

Transport .................. 0 - 6.6 mph (10.6 kph)

Reverse..................... 0 - 3.5 mph (5.6 kph)

Hydraulic System:

Capacity.......................... 5 U.S. gal. (19 liters) System

Fluid Type ....................... GreensCare 46 Biodegradable

Filter................................ Full Flow 20 micron

Steering ......................... Hydrostatic power steering

Mower Lift ....................... Hydraulic Double Acting Cylinders

3.5 WEIGHTS AND DIMENSIONS ________________________________________________

Dimensions: Inches (mm)

Length - Grass Catchers On ........................ 99.5 (2526)

Height - Top of ROPS...................................... 78 (1981)

Wheel Base.................................................. 52.8 (1341)

Width - Transport Position ............................... 68 (1727)

Width - Mowing Position.................................. 70 (1778)

Width - Wheel .............................................. 50.5 (1283)

Turning Radius................................................ 18 (457)

Weights: Lbs. (kg)

Working Weight Less Operator

62304 .......................................................... 1468 (666)

3.6 ACCESSORIES & SUPPORT LITERATURE _____________________________________

Contact your area Jacobsen Dealer for a complete listing of accessories and attachments.

Accessories

Orange Touch-up Paint (12 oz. spray) ...................... 554598

Arm Rest ................................................................. 4139431

Grass Catcher............................................................. 67891

Brush, 62 in................................................................. 68623

Fine Bristle Brush........................................................ 68536

Green Sentry II Oil System Monitor ............................ 68669

Light Kit ................................................................... 2811910

Motor / Light / Brush Mounting Kit........................... 2811909

Rear Roller Cleaner .................................................... 68643

Quick Roller (Set of 3)................................................. 68664

Spiker (Set of 3) .......................................................... 68665

Traction Tire (Set of 2)................................................. 62616

Turf Groomer 1/4 in. Spacing R.H. (2 Required)......... 67911

Turf Groomer 1/4 in. Spacing L.H. (1 Required) ......... 67912

Turf Groomer 1/2 in. Spacing R.H. (2 Required)......... 67913

Turf Groomer 1/2 in. Spacing L.H. (1 Required) ......... 67914

Vertical Mower L.H. (1 Required)................................ 68549

Vertical Mower R.H. (2 Required) ............................... 68550

Variable Step Cut ........................................................ 68551

High Cut Roller Kit ...................................................... 68634

MAGSystem™ Kit ................................................... 4158083

Reels

7 Blade Reel L.H. (1 Required)....................................62841

7 Blade Reel R.H. (2 Required) ...................................62842

9 Blade Reel L.H. (1 Required)....................................62843

9 Blade Reel R.H. (2 Required) ...................................62844

11 Blade Reel L.H. (1 Required)..................................62845

11 Blade Reel R.H. (2 Required) .................................62846

15 Blade Reel L.H. (1 Required)..................................62847

15 Blade Reel R.H. (2 Required) .................................62848

Rollers

Grooved Front Roller ...................................................68527

Solid Roller .................................................................68530

Segmented Front Roller...............................................68673

Grooved Front Roller (Steel)........................................68613

Grooved Front Roller (Aluminum) ................................68614

Grooved Rear Roller....................................................68580

Support Literature

Safety & Operation Manual......................................4212747

Parts & Maintenance Manual...................................4304388

Diesel Engine Parts Catalog....................................4304580

Operator Training Video...........................................4191631

Service & Repair Manual.........................................4171649

CAUTION

Use of other than Jacobsen authorized parts and accessories may cause personal injury or damage to the

equipment.

3 SPECIFICATIONS

3.7 DECLARATION OF CONFORMITY ____________________________________________

DECLARATION OF CONFORMITY ▪ ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ ▪ PROHLÁŠENÍ O SHODĚ ▪

OVERENSSTEMMELSESERKLÆRING ▪ CONFORMITEITSVERKLARING ▪ VASTAVUSDEKLARATSIOON ▪

VAATIMUSTENMUKAISUUSVAKUUTUS ▪ DECLARATION DE CONFORMITE ▪ KONFORMITÄTSERKLÄRUNG ▪

∆ΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ▪ MEGFELELŐSÉGI NYILATKOZAT ▪ DICHIARAZIONE DI CONFORMITÀ ▪ ATBILSTĪBAS

DEKLARĀCIJA ▪ ATITIKTIES DEKLARACIJA ▪ DIKJARAZZJONI TAL-KONFORMITÀ ▪ DEKLARACJA ZGODNOŚCI ▪

DECLARAÇÃO DE CONFORMIDADE ▪ DECLARAŢIE DE CONFORMITATE ▪ VYHLÁSENIE O ZHODE ▪ IZJAVA O

SKLADNOSTI ▪ DECLARACIÓN DE CONFORMIDAD ▪ DEKLARATION OM ÖVERENSSTÄMMELSE

Business name and full address of the manufacturer ▪ Търговско име и пълен адрес на производителя ▪ Obchodní jméno a plná adresa výrobce ▪

Producentens firmanavn og fulde adresse ▪ Bedrijfsnaam en volledig adres van de fabrikant ▪ Tootja ärinimi ja täielik aadress ▪

Valmistajan toiminimi ja täydellinen osoite ▪ Nom commercial et adresse complète du fabricant ▪ Firmenname und vollständige Adresse des Herstellers ▪

Επωνυμία και ταχυδρομική διεύθυνση κατασκευαστή ▪ A gyártó üzleti neve és teljes címe ▪ Ragione sociale e indirizzo completo del fabbricante ▪

Uzņēmuma nosaukums un pilna ražotāja adrese ▪ Verslo pavadinimas ir pilnas gamintojo adresas ▪ Isem kummerċjali u indirizz sħiħ tal-fabbrikant ▪

Nazwa firmy i pełny adres producenta ▪ Nome da empresa e endereço completo do fabricante ▪ Denumirea comercială şi adresa completă a

producătorului ▪ Obchodný názov a úplná adresa výrobcu ▪ Naziv podjetja in polni naslov proizvajalca ▪ Nombre de la empresa y dirección completa del

fabricante ▪ Tillverkarens företagsnamn och kompletta adress

Jacobsen, A Textron Company

11524 Wilmar Blvd.

Charlotte, NC 28273, USA

Product Code ▪ Код

на продукта ▪ Kód výrobku ▪ Produktkode ▪ Productcode ▪ Toote kood ▪ Tuotekoodi ▪ Code produit ▪ Produktcode ▪ Κωδικός προϊόντος

▪ Termékkód ▪ Codice prodotto ▪ Produkta kods ▪ Produkto kodas ▪ Kodiċi tal-Prodott ▪ Kod produktu ▪ Código do Produto ▪ Cod produs ▪ Kód výrobku ▪

Oznaka proizvoda ▪ Código de producto ▪ Produktkod

62304

62379

Machine Name ▪ Наименование на машината ▪ Název stroje ▪ Maskinnavn ▪ Machinenaam ▪ Masina nimi ▪ Laitteen nimi ▪ Nom de la machine ▪

Maschinenbezeichnung ▪ Ονομασία μηχανήματος ▪ Gépnév ▪ Denominazione della macchina ▪ Iekārtas nosaukums ▪ Mašinos pavadinimas ▪ Isem tal-

Magna ▪ Nazwa urządzenia ▪

Nome da Máquina ▪ Numele echipamentului ▪ Názov stroja ▪ Naziv stroja ▪ Nombre de la máquina ▪ Maskinens namn

Greens King IV Plus Diesel

Designation ▪ Предназначение ▪ Označení ▪ Betegnelse ▪ Benaming ▪ Nimetus ▪ Tyyppimerkintä ▪ Pažymėjimas ▪ Bezeichnung ▪ Χαρακτηρισμός ▪

Megnevezés ▪ Funzione ▪ Apzīmējums ▪ Lithuanian ▪ Denominazzjoni ▪ Oznaczenie ▪ Designação ▪ Specificaţie ▪ Označenie ▪ Namen stroja ▪ Descripción

▪ Beteckning

Lawnmower, Article 12, Item 32

Serial Number ▪ Сериен номер ▪ Sériové číslo ▪ Serienummer ▪ Serienummer ▪ Seerianumber ▪ Valmistusnumero ▪ Numéro de série ▪ Seriennummer ▪

Σειριακός αριθμός

▪ Sorozatszám ▪ Numero di serie ▪ Sērijas numurs ▪ Serijos numeris ▪ Numru Serjali ▪ Numer seryjny ▪ Número de Série ▪ Număr de

serie ▪ Sériové číslo ▪ Serijska številka ▪ Número de serie ▪ Serienummer

6237901601-6237902500

Engine ▪ Двигател ▪ Motor ▪ Motor ▪ Motor ▪ Mootor ▪ Moottori ▪ Moteur ▪ Motor ▪ Μηχανή ▪ Modulnév ▪ Motore ▪ Dzinējs ▪ Variklis ▪ Saħħa Netta Installata ▪

Silnik ▪ Motor ▪ Motor ▪ Motor ▪ Motor ▪ Motor ▪ Motor

Kubota D722-E3B Diesel

Net Installed Power ▪ Нетна инсталирана мощност ▪ Čistý instalovaný výkon

▪ Installeret nettoeffekt ▪ Netto geïnstalleerd vermogen ▪ Installeeritud

netovõimsus ▪ Asennettu nettoteho ▪ Puissance nominale nette ▪ Installierte Nettoleistung ▪ Καθαρή εγκατεστημένη ισχύς ▪ Nettó beépített teljesítmény ▪

Potenza netta installata ▪ Paredzētā tīkla jauda ▪ Grynoji galia ▪ Wisa’ tal-Qtugħ ▪ Moc zainstalowana netto ▪ Potência instalada ▪ Puterea instalată netă ▪

Čistý inštalovaný výkon ▪ Neto vgrajena moč ▪ Potencia instalada neta ▪ Nettoeffekt

13,2 kW @ 3200 RPM

Cutting Width ▪ Широчина на рязане ▪ Šířka řezu ▪ Skærebredde ▪ Maaibreedte ▪ Lõikelaius ▪ Leikkuuleveys ▪ Largeur de coupe ▪ Schnittbreite ▪

Μήκος μισινέζας ▪ Vágási szélesség ▪ Larghezza di taglio ▪

Griešanas platums ▪ Pjovimo plotis ▪ Tikkonforma mad-Direttivi ▪ Szerokość cięcia ▪

Largura de Corte ▪ Lăţimea de tăiere ▪ Šírka záberu ▪ Širina reza ▪ Anchura de corte ▪ Klippbredd

157 cm

Conforms to Directives ▪ В съответствие с директивите ▪ Splňuje podmínky směrnic ▪ Er i overensstemmelse med direktiver ▪ Voldoet aan de richtlijnen ▪

Vastab direktiividele ▪ Direktiivien mukainen ▪ Conforme aux directives ▪ Entspricht Richtlinien ▪ Ακολουθήστε πιστά τις Οδηγίες ▪ Megfelel az irányelveknek

▪ Conforme alle Direttive ▪ Atbilst direktīvām ▪ Atitinka direktyvų reikalavimus ▪ Valutazzjoni tal-Konformità ▪ Dyrektywy związane ▪ Cumpre as Directivas ▪

Respectă Directivele ▪ Je v súlade so smernicami ▪ Skladnost z direktivami ▪

Cumple con las Directivas ▪ Uppfyller direktiv

2004/108/EC

2006/42/EC

2000/14/EC, 2005/88/EC

2006/66/EC

Conformity Assessment ▪ Оценка за съответствие ▪ Hodnocení plnění podmínek ▪ Overensstemmelsesvurdering ▪ Conformiteitsbeoordeling ▪

Vastavushindamine ▪ Vaatimustenmukaisuuden arviointi ▪ Evaluation de conformité ▪ Konformitätsbeurteilung ▪ ∆ιαπίστωση Συμμόρφωσης ▪

Megfelelőség-értékelés ▪ Valutazione della conformità ▪ Atbilstības novērtējums ▪ Atitikties įvertinimas ▪ Livell tal-Qawwa tal-Ħoss Imkejjel ▪ Ocena

zgodności ▪ Avaliação de Conformidade ▪ Evaluarea conformităţii ▪ Vyhodnotenie zhodnosti ▪ Ocena skladnosti ▪ Evaluación de conformidad ▪

Bedömning av överensstämmelse

2006/42/EC Annex VIII

Measured Sound Power Level ▪ Измерено ниво на звукова мощност ▪ Naměřený akustický výkon ▪ Målte lydstyrkeniveau

▪ Gemeten geluidsniveau ▪

Mõõdetud helivõimsuse tase ▪ Mitattu äänitehotaso ▪ Niveau de puissance sonore mesuré ▪ Gemessener Schalldruckpegel ▪

Σταθμισμένο επίπεδο ηχητικής ισχύος ▪ Mért hangteljesítményszint ▪ Livello di potenza sonora misurato ▪ Izmērītais skaņas jaudas līmenis ▪

Išmatuotas garso stiprumo lygis ▪ Livell tal-Qawwa tal-Ħoss Iggarantit ▪ Moc akustyczna mierzona ▪ Nível sonoro medido ▪ Nivelul măsurat al puterii

acustice ▪ Nameraná hladina akustického výkonu ▪ Izmerjena raven zvočne moči ▪ Nivel de potencia sonora medido ▪ Uppmätt ljudeffektsnivå

102 dB(A) LWA

Guaranteed Sound Power Level ▪ Гарантирано ниво на звукова мощност ▪ Garantovaný akustický výkon ▪ Garanteret lydstyrkeniveau ▪

Gegarandeerd geluidsniveau ▪ Garanteeritud helivõimsuse tase ▪ Taattu äänitehotaso ▪ Niveau de puissance sonore garanti ▪ Garantierter

Schalldruckpegel ▪ Εγγυημένο επίπεδο ηχητικής

ισχύος ▪ Szavatolt hangteljesítményszint ▪ Livello di potenza sonora garantito ▪ Garantētais skaņas

jaudas līmenis ▪ Garantuotas garso stiprumo lygis ▪ Livell tal-Qawwa tal-Ħoss Iggarantit ▪ Moc akustyczna gwarantowana ▪ Nível sonoro farantido ▪

Nivelul garantat al puterii acustice ▪ Garantovaná hladina akustického výkonu ▪ Zajamčena raven zvočne moči ▪ Nivel de potencia sonora garantizado ▪

Garanterad ljudeffektsnivå

102dB(A) LWA

Conformity Assessment Procedure (Noise) ▪ Оценка за съответствие на процедурата (Шум) ▪ Postup hodnocení plnění podmínek (hluk) ▪

Procedure for overensstemmelsesvurdering (Støj) ▪ Procedure van de conformiteitsbeoordeling (geluid) ▪ Vastavushindamismenetlus (müra) ▪

Vaatimustenmukaisuuden arviointimenettely (Melu) ▪ Procédure d’évaluation de conformité (bruit) ▪ Konformitätsbeurteilungsverfahren (Geräusch) ▪

∆ιαδικασία Αξιολόγησης Συμμόρφωσης (Θόρυβος) ▪ Megfelelőség-értékelési eljárás (Zaj) ▪ Procedura di valutazione della conformità (rumore) ▪

Atbilstības novērtē

juma procedūra (troksnis) ▪ Atitikties įvertinimo procedūra (garsas) ▪ Proċedura tal-Valutazzjoni tal-Konformità (Ħoss) ▪

Procedura oceny zgodności (poziom hałasu) ▪ Processo de avaliação de conformidade (nível sonoro) Procedura de evaluare a conformităţii (zgomot) ▪

Postup vyhodnocovania zhodnosti (hluk) ▪ Postopek za ugotavljanje skladnosti (hrup) ▪ Procedimiento de evaluación de conformidad (ruido) ▪

Procedur för bedömning av överensstämmelse (buller)

2000/14/EC Annex VI, Part 1

UK Notified Body for 2000/14/EC ▪ Нотифициран орган в Обединеното кралство за 2000/14/ЕО ▪ Úřad certifikovaný podle směrnice č. 2000/14/EC ▪

Det britiske bemyndigede organ for 2001/14/EF ▪ Engels adviesorgaan voor 2000/14/EG ▪ Ühendkuningriigi teavitatud asutus direktiivi 2000/14/EÜ

mõistes ▪ Direktiivin 2000/14/EY mukainen ilmoitettu tarkastuslaitos Isossa-Britanniassa ▪ Organisme notifié concernant la directive 2000/14/CE ▪

Britische benannte Stelle für 2000/14/EG ▪ Κοινοποιημένος Οργανισμός Ηνωμένου Βασιλείου για 2000/14/ΕΚ ▪

2000/14/EK – egyesült királyságbeli bejelentett szervezet ▪ Organismo Notificato in GB per 2000/14/CE ▪ 2000/14/EK AK reģistrē

tā organizācija ▪

JK notifikuotosios įstaigos 2000/14/EC ▪ Korp Notifikat tar-Renju Unit għal 2000/14/KE ▪ Dopuszczona jednostka badawcza w Wielkiej Brytanii wg 2000/

14/WE ▪ Entidade notificada no Reino Unido para 2000/14/CE ▪ Organism notificat în Marea Britanie pentru 2000/14/CE ▪

Notifikovaný orgán Spojeného kráľovstva pre smernicu 2000/14/ES ▪ Britanski priglašeni organ za 2000/14/ES ▪

Cuerpo notificado en el Reino Unido para 2000/14/CE ▪ Anmält organ för 2000/14/EG i Storbritannien

Number: 1088

Sound Research Laboratories Limited

Holbrook House, Little Waldingfield

Sudbury, Suffolk CO10 0TH

Operator Ear Noise Level ▪ Оператор на нивото на доловим от ухото шум ▪ Hladina hluku v oblasti uší operátora ▪ Støjniveau i førers ørehøjde ▪

Geluidsniveau oor bestuurder ▪ Müratase operaatori kõrvas ▪ Melutaso käyttäjän korvan kohdalla ▪ Niveau de bruit à hauteur des oreilles de l’opérateur ▪

Schallpegel am Bedienerohr ▪ Επίπεδο θορύβου σε λειτουργία ▪ A kezelő fülénél mért zajszint ▪ Livello di potenza sonora all’orecchio dell’operatore ▪

Trokšņa līmenis pie operatora auss ▪ Dirbančiojo su mašina patiriamo triukšmo lygis ▪ Livell tal-

Ħoss fil-Widna tal-Operatur ▪

Dopuszczalny poziom hałasu dla operatora ▪ Nível sonoro nos ouvidos do operador ▪ Nivelul zgomotului la urechea operatorului ▪

Hladina hluku pôsobiaca na sluch operátora ▪ Raven hrupa pri ušesu upravljavca ▪ Nivel sonoro en el oído del operador ▪ Ljudnivå vid förarens öra

87 dB(a) Leq (2006/42/EC)

SPECIFICATIONS 3

Harmonised standards used ▪ Използвани хармонизирани стандарти ▪ Použité harmonizované normy ▪ Brugte harmoniserede standarder ▪

Gebruikte geharmoniseerde standaards ▪ Kasutatud ühtlustatud standardid ▪ Käytetyt yhdenmukaistetut standardit ▪ Normes harmonisées utilisées ▪

Angewandte harmonisierte Normen ▪ Εναρμονισμένα πρότυπα που χρησιμοποιήθηκαν ▪ Harmonizált szabványok ▪ Standard armonizzati applicati ▪

Izmantotie saskaņotie standarti ▪ Panaudoti suderinti standartai ▪ Standards armonizzati użati ▪ Normy spójne powiązane ▪ Normas harmonizadas usadas

▪ Standardele armonizate utilizate ▪ Použité harmonizované normy ▪ Uporabljeni usklajeni standardi ▪ Estándares armonizados utilizados ▪

Harmoniserade standarder som används

BS EN ISO 20643

BS EN ISO 5349-1

BS EN ISO 5349-2

BS EN 836

Technical standards and specifications used ▪ Използвани технически стандарти и спецификации ▪ Použité technické normy a specifikace ▪

Brugte tekniske standarder og specifikationer ▪ Gebruikte technische standaards en specificaties ▪ Kasutatud tehnilised standardid ja spetsifikatsioonid ▪

Käytetyt tekniset standardit ja eritelmät ▪ Spécifications et normes techniques utilisées ▪ Angewandte technische Normen und Spezifikationen ▪

Τεχ νικά

πρότυπα και προδιαγραφές που χρησιμοποιήθηκαν ▪ Műszaki szabványok és specifikációk ▪ Standard tecnici e specifiche applicati ▪

Izmantotie tehniskie standarti un specifikācijas ▪ Panaudoti techniniai standartai ir techninė informacija ▪ Standards u speċifikazzjonijiet tekniċi użati ▪

Normy i specyfikacje techniczne powiązane ▪ Normas técnicas e especificações usadas ▪ Standardele tehnice şi specificaţiile utilizate ▪

Použité technické normy a špecifikácie ▪ Uporabljeni tehnični standardi in specifikacije ▪ Estándares y especificaciones técnicas utilizadas ▪

Tekniska standarder och specifikationer som används

B71.4

ISO 2631-1

ISO 21299

The place and date of the declaration ▪ Място и дата на декларацията ▪ Místo a datum prohlášení ▪ Sted og dato for erklæringen ▪

Plaats en datum van de verklaring ▪ Deklaratsiooni väljastamise koht ja kuupäev ▪ Vakuutuksen paikka ja päivämäärä ▪ Lieu et date de la déclaration ▪

Ort und Datum der Erklärung ▪ Τόπος και ημερομηνία δήλωσης ▪

A nyilatkozat kelte (hely és idő) ▪ Luogo e data della dichiarazione ▪

Deklarācijas vieta un datums ▪ Deklaracijos vieta ir data ▪ Il-post u d-data tad-dikjarazzjoni ▪ Miejsce i data wystawienia deklaracji ▪ Local e data da

declaração ▪ Locul şi data declaraţiei ▪ Miesto a dátum vyhlásenia ▪ Kraj in datum izjave ▪ Lugar y fecha de la declaración ▪ Plats och datum för

deklarationen

Jacobsen, A Textron Company

11524 Wilmar Blvd.

Charlotte, NC 28273, USA

February 5th, 2014

Signature of the person empowered to draw up the declaration on behalf of the manufacturer, holds the technical documentation and is authorised to

compile the technical file, and who is established in the Community.

Подпис на човека, упълномощен да състави декларацията от името на производителя, който поддържащ техническата документация и е

оторизиран да изготви техническия файл и е регистриран в общността.

Podpis osoby oprávněné sestavit prohlášení jménem výrobce, držet technickou dokumentaci a osoby oprávněné sestavit technické soubory a založené v

rámci Evropského společ

enství.

Underskrift af personen, der har fuldmagt til at udarbejde erklæringen på vegne af producenten, der er indehaver af dokumentationen og er bemyndiget til

at udarbejde den tekniske journal, og som er baseret i nærområdet.

Handtekening van de persoon die bevoegd is de verklaring namens de fabrikant te tekenen, de technische documentatie bewaart en bevoegd is om het

technische bestand samen te stellen, en die is gevestigd in het Woongebied.

Ühenduse registrisse kantud isiku allkiri, kes on volitatud tootja nimel deklaratsiooni koostama, kes omab tehnilist dokumentatsiooni ja kellel on õigus

koostada tehniline toimik.

Sen henkilön allekirjoitus, jolla on valmistajan valtuutus vakuutuksen laadintaan, jolla on hallussaan tekniset asiakirjat, joka on valtuutettu laatimaan

tekniset asiakirjat ja joka on sijoittautunut yhteisöön.

Signature de la personne habilitée à rédiger la déclaration au nom du fabricant, à détenir la documentation technique, à compiler les fichiers techniques et

qui est implantée dans la Communauté.

Unterschrift der Person, die berechtigt ist, die Erklärung im Namen des Herstellers abzugeben, die die technischen Unterlagen aufbewahrt und berechtigt

ist, die technischen Unterlagen zusammenzustellen, und die in der Gemeinschaft niedergelassen ist.

Υπογραφή ατόμου εξουσιοδοτημένου για την σύνταξη της δήλωσης εκ μέρους του κατασκευαστή, ο οποίος κατέχει την τεχνική έκθεση και έχει την

εξουσιοδότηση να ταξινομήσει τον τεχνικό φάκελο και ο οποίος είναι διορισμένος στην Κοινότητα.

A gyártó nevében meghatalmazott személy, akinek jogában áll módosítania a nyilatkozatot, a műszaki dokumentációt őrzi, engedéllyel rendelkezik a

műszaki fájl összeállításához, és aki a közösségben letelepedett személy.

Firma della persona autorizzata a redigere la dichiarazione a nome del fabbricante, in possesso Della documentazione tecnica ed autorizzata a costituire

il fascicolo tecnico, che deve essere stabilita nella Comunità.

Tās personas paraksts, kura ir pilnvarota deklarācijas sastā

dīšanai ražotāja vārdā, kurai ir tehniskā dokumentācija, kura ir pilnvarota sagatavot tehnisko

reģistru un kura ir apstiprināta Kopienā.

Asmuo, kuris yra gana žinomas, kuriam gamintojas suteikė įgaliojimus sudaryti šią deklaraciją, ir kuris ją pasirašė, turi visą techninę informaciją ir yra

įgaliotas sudaryti techninės informacijos dokumentą.

Il-firma tal-persuna awtorizzata li tfassal id-dikjarazzjoni f’isem il-fabbrikant, għandha d-dokumentazzjoni teknika u hija awtorizzata li tikkompila l-fajl

tekniku u li hija stabbilita fil-Komunità.

Podpis osoby upoważnionej do sporządzenia deklaracji w imieniu producenta, przechowującej dokumentację techniczną, upoważnioną do stworzenia

dokumentacji technicznej oraz wyznaczonej ds. wspólnotowych.

Assinatura da pessoa com poderes para emitir a declaração em nome do fabricante, que possui a documentação técnica, que está autorizada a compilar

o processo técnico e que está estabelecida na Comunidade.

Semnătura persoanei împuternicite să elaboreze declaraţia în numele producătorului, care deţine documentaţia tehnică, este autorizată să compileze

dosarul tehnic şi este stabilită în Comunitate.

Podpis osoby poverenej vystavením vyhlásenia v mene výrobcu, ktorá má technickú dokumentáciu a je oprávnená spracovať technické podklady a ktorá

je umiestnená v Spoločenstve.

Podpis osebe, pooblaščene za izdelavo izjave v imenu proizvajalca, ki ima tehnično dokumentacijo in lahko sestavlja spis tehni

čne dokumentacije, ter ima

sedež v Skupnosti.

Firma de la persona responsable de la declaración en nombre del fabricante, que posee la documentación técnica y está autorizada para recopilar el

archivo técnico y que está establecido en la Comunidad.

Undertecknas av den som bemyndigad att upprätta deklarationen å tillverkarens vägnar, innehar den tekniska dokumentationen och är bemyndigad att

sammanställa den tekniska informationen och som är etablerad i gemenskapen.

2006/42/EC Annex II 1.A.2

Tim Lansdell

Technical Director

Ransomes Jacobsen Limited

West Road, Ransomes Europark,

Ipswich, IP3 9TT, England

2006/42/EC Annex II 1.A.10

Vasant Godhalekar

VP of Engineering

Jacobsen, A Textron Company

11524 Wilmar Blvd,

Charlotte, NC 28273, USA

Certificate Number ▪ Номер на сертификат ▪ Číslo osvědčení ▪ Certifikatnummer ▪ Certificaatnummer ▪ Sertifikaadi number ▪ Hyväksyntänumero ▪

Numéro de certificat ▪ Bescheinigungsnummer ▪ Αριθμός Πιστοποιητικού ▪ Hitelesítési szám ▪ Numero del certificato ▪ Sertifikāta numurs ▪

Sertifikato numeris ▪ Numru taċ-Ċertifikat ▪ Numer certyfikatu ▪ Número do Certificado ▪ Număr certificat ▪ Číslo osvedčenia ▪ Številka certifikata ▪

Número de certificado ▪ Certifikatsnummer

4212747 Rev B

4 DECALS

4.1 DECALS _________________________________________________________________

Familiarize yourself with the following decals. They are critical to the safe operation of the

machine. REPLACE DAMAGED DECALS IMMEDIATELY.

4181864

4181865 REV B

Danger

To avoid injury when working with battery:

1. Always connect the black (-) ground last and remove it

first.

2. Keep sparks and flames away, and avoid contact with

acid.

To avoid injury when jumping battery:

1. Connect positive (+) terminal to positive (+) terminal.

2. Connect negative (-) terminal on good battery to frame

of vehicle that has dead battery.

• Read operator's manual. Do not allow untrained

operators to use machine.

• Keep shields in place and hardware securely

fastened.

• Keep hands, feet, and clothing away from moving

parts.

• Before you clean, adjust, or repair this equipment,

disengage all drives, engage parking brake, and stop

engine.

• Never carry passengers.

• Keep bystanders away.

• Do not use on slopes greater than 12.5°.

4182520

DANGER

To prevent injury, disengage all drives,

engage parking brake and stop engine

before working on machine or emptying

grass catchers.

DECALS 4

Familiarize yourself with the following decals. They are critical to the safe operation of the

machine. REPLACE DAMAGED DECALS IMMEDIATELY.

4181863

WARNING

Read manual for service. Torsion

spring under extreme tension.

Clamp may turn suddenly. To avoid

injury, unwind spring by tapping on

clamp while loosening nut. (Located

on lift arms)

WARNING

Read manual for service. To prevent

cuts, do not turn reel by hand. Use

socket wrench or Turf Groomer™

knob to turn reel. (Located on reel

frame)

4181860

WARNING

Read manual. Reels will rotate in

the raised position with reel control

lever(s) set for reverse rotation.

Keep hands and feet away from the

reels to prevent serious injury.

4205183

WARNING

Do not use for towing.

4181862

WARNING

Radiator is under pressure. Remove

cap slowly to avoid personal injury.

4 DECALS

Mix equal parts of clean water and a premium quality

ethylene glycol based anti-freeze to maintain the boil

over, rust and corrosion protection.

Drain and disca rd coolant yearly. Read manual for

additional instructions.

THIS RADIATOR CONTAINS

ANTI-FREEZE

PROTECTED TO -26°F (-32°C)

363995

IMPO R T AN T

2811912

This machine us e s Greens Care 46,

a biodeg radable hydraulic fluid.

(Order 5003 105 for 5 g al. pail)

U s e of ATF Dextron II or III

i s an approved alternate fluid.

U s e will compromis e all

biodeg radable properties of

Greens Care 46 hydraulic fluid.

4181861

IMPORTANT

DO NOT USE STARTING ASSIST FLUIDS

Use of starting assist fluids in the air intake

system may be potentially explosive or cause a

“runaway” engine condition. This could result in

serious engine damage.

DECALS 4

Familiarize yourself with the following decals. They are critical to the safe operation of the

machine. REPLACE DAMAGED DECALS IMMEDIATELY.

2812066

8-12 p.s.i.

(55-83 kPa)

105

4141266

3-5

3009744

Brake

Reel Switches Wiring

Tire Pressure

Noise Level

Engine Oil

Pressure

Backlap Switch

Ignition Switch

Start

RUN

OFF

Backlap

Operation

Normal

Operation

Glow Plug On

Glow Plug Off

30 Amp Glow

Plug Fuse

Engine

Throttle

Slow

Fast

3002309

Diesel Fuel

4 DECALS

Right ReelCenter ReelLeft Reel

Reel Forward

Rotation

Reel Off

Reel Reverse

Rotation

Parking Brake

Disengaged

Transport

Mow

Neutral

Reverse

Traction Lever

Parking Brake

Engaged

Charging

System Fuse

Interlock

System Fuse

CONTROLS 5

5 CONTROLS

5.1 ICONS ___________________________________________________________________

WARNING

Never attempt to drive the mower unless you have read the Safety and Operation Manual

and know how to operate all controls correctly.

Familiarize yourself with the icons shown above and what they represent. Learn the

location and purpose of all of the controls and gauges before operating this mower.

Read Manual

Off Run Start

Engine

Fast

Slow

Engine Throttle

Forward Reverse

Reel Rotation

Fuse

Circuit Breaker

Choke

Headlight

Engaged Disengaged

Parking Brake

Hydraulic Oil Leak

Horn

Service Foot Brake

Hour Meter

Raise

Lower

Enable Disable

Reel Switch

Forward

Reverse

Traction Lever

Transport

Mow

Neutral

Reverse

Mow/Lift Treadle

Fuel

Diesel

Coolant

Temperature

Glow Plug

Off

5 CONTROLS

3-5

A Reel Control Lever

B Parking Brake Lever

C Traction Lever

D Temperature Gauge (Diesel)

E Volt Meter

F Ignition Switch

G Mechanics (Backlap) Switch

H Light Switch (Optional)

J Lights Fuse (Optional)

K Charging Circuit Fuse

L Interlock System Fuse

M Parking Brake Light

N Oil Pressure Light

P Throttle

R Glow Plug Fuse

S Glow Plug Switch

T Accelerator Pedal

U Brake Pedal

V Tilt Control

W Mow/Lift Pedal

X Hour Meter

Y Seat Control Lever

Z Hydraulic Cap/Dipstick

AA Fuel Cap

CONTROLS 5

5.2 CONTROL DESCRIPTIONS __________________________________________________

A. Reel Control Levers - Used to operate the cutting

units. Push lever(s) forward for forward rotation. Pull

lever(s) back for Reverse rotation. All three levers

must be in OFF position to start engine.

B. Parking Brake Lever - Pull lever back to engage

and push lever forward to disengage parking brake.

Always disengage parking brake slowly. Parking

brake must be engaged to start engine.

C. Traction Lever - Four Positions: Transport (2), Mow

(1), Neutral (N) and Reverse (R). Traction lever must

be in Neutral position to start engine.

D. Temperature Gauge (Diesel Units) - Indicates

engine coolant temperature. Normal operating

temperatures should be 185° - 195° F (85° - 91° C).

E. Volt Meter - Used to monitor battery condition.

During normal operation, volt meter needle should

never be in the red area.

F. Ignition Switch - Used to start the engine. To

prevent unauthorized operation, remove the ignition

key when mower is not in use.

G. Mechanic’s (Backlap) Switch - Used to switch the

mower to backlap mode to hone or sharpen the

reel.

H. Light Switch (Optional) - Used to control operation

of optional light kit.

J. Fuse, Lights - 20 Amp fuse, protecting light circuit.

K. Fuse, Charging Circuit - 30 Amp fuse, Protecting

charging circuit.

L. Fuse, Interlock System - 6 Amp fuse, protecting

Interlock System.

M. Parking Brake Light is always on when parking

brake is engaged. Do not move traction lever out of

Neutral, or press accelerator pedal when light is on.

N. Engine Oil Pressure Light - Indicator will light if

engine oil pressure drops below a safe level. Stop

engine immediately, determine the cause, and

correct problem before restarting engine.

P. Throttle - Regulates Engine Speed. Push Lever

forward to increase or pull lever back to decrease

engine speed.

R. Fuse, Glow Plug - 40 Amp fuse, protecting glow

plug circuit.

S. Glow Plug Switch - Used to energize the glow

plugs. Push toggle switch forward and hold for 3 - 5

seconds, then release the switch. Do not depress

the switch for more than 5 seconds.

T. Accelerator Pedal - Used to control speed of the

mower. Do not depress pedal if parking brake light

(L) is on.

Remove foot from pedal, the accelerator pedal will

return to Neutral, and the machine will stop. The self

braking action is in forward direction only.

U. Brake Pedal - Used to stop mower when traveling

in Reverse. Remove foot from accelerator and

depress brake pedal.

V. Mow/Lift Pedal - Used to lift or lower the cutting

units. Depress and hold front of pedal to lower

cutting units, or depress and hold rear of pedal to

raise cutting units.

W. Hour Meter - Used to time maintenance intervals or

mowing operations. The meter operates only when

ignition key is in RUN position.

X. Seat Control Lever - Used to adjust position of

seat. Pull lever forward and adjust seat to

comfortable position, then release lever.

Y. Hydraulic Cap/Dipstick - Used to check level of

hydraulic fluid in tank. Level should always be at Full

mark on dipstick.

Z. Fuel Cap - Remove cap to add fuel, or check fuel

level in tank. Always replace cap tightly.

WARNING

Reels will rotate in the raised position with reel control

lever(s) set for reverse rotation. Keep hands and feet

away from the reels to prevent serious injury.

DANGER

Reels will turn with mechanics key in backlap position

without an operator on the seat. Keep hands and feet

away from the reels to prevent serious injury.

NOTICE

When operating the mow/lift pedal, keep the pedal

depressed until the cutting units have been fully

lowered or raised, then release the pedal.

6 OPERATION

6.1 DAILY INSPECTION________________________________________________________

1. Perform a visual inspection of the entire unit, look for

signs of wear, loose hardware, and missing or

damaged components. Check for fuel or oil leaks to

ensure connections are tight and hoses and tubes

are in good condition.

2. Check the fuel supply, radiator coolant level,

crankcase oil, and air cleaner indicator. All fluids

must be at the Full level mark with engine cold.

3. Make sure all mowers are adjusted to the same

cutting height.

4. Check tires for proper inflation.

5. Test the Interlock system.

Note: For more detailed maintenance information,

adjustments and maintenance/lube charts, see the

Parts & Maintenance manual.

6.2 INTERLOCK SYSTEM ______________________________________________________

1. The Interlock system prevents the engine from

starting unless the parking brake is engaged, the

traction lever is in Neutral and the reel levers are off.

The system also stops the engine if the operator

leaves the seat with the reel levers on, traction lever

out of Neutral, or parking brake disengaged.

2. Perform each of the following tests to insure the

Interlock system is functioning properly. Stop the

test and have the system inspected and repaired if

any of the tests fail as listed below:

 the engine does not start in test 1;

 the engine does start during tests 2, 3 or 4;

 the engine continues to run during tests 5 or 6.

3. Refer to the chart below for each test and follow the

check () marks across the chart. Shut engine off

between each test.

Test 1: Represents normal starting procedure. The

operator is seated, parking brake is engaged, the

traction lever is in Neutral, and the reel levers are off.

The engine should start.

Test 2: The engine must not start if the reel lever is in

Forward or Reverse. Repeat test for each reel lever

and lever position.

Test 3: The engine must not start if the parking brake

is disengaged.

Test 4: The engine must not start if traction lever is

not in Neutral. Repeat test for each position of lever.

Test 5: Start the engine in the normal manner then

turn reel lever on and lift your weight off the seat.

Repeat test for each reel lever and lever position.



Test 6: Start the engine in the normal manner then

disengage parking brake and lift your weight off the

seat.



Test 7: Start the engine in the normal manner then

shift traction lever out of Neutral and lift your weight

off the seat. Repeat test for each lever position.



CAUTION

The daily inspection should be performed only when

the engine is off and all fluids are cold. Lower mowers

to the ground, engage the parking brake, stop engine,

and remove ignition key.

WARNING

Never operate equipment with the Interlock

system disconnected or malfunctioning. Do not

disconnect or bypass any switch.

Test Operator

Seated

Parking

Brake

Traction Lever

in Neutral

Reel

Levers

Engine

Starts

Yes No Engaged Disengaged Yes No On Off Yes No

1   

2   

3 

4   

5 







6 



 



7 







OPERATION 6

Lift your weight off seat. The engine will shut down.

6.3 OPERATING PROCEDURES ______________________________________________________

1. Under no circumstances should the engine be

started without the operator seated on the mower.

2. Do not operate mower or attachments with loose,

damaged, or missing components. Whenever

possible mow when grass is dry.

3. First mow in a test area to become thoroughly

familiar with the operation of the mower and control

levers.

4. Study the area to determine the best and safest

operating procedure. Consider the height of the

grass, type of terrain, and condition of the surface.

Each condition will require certain adjustments or

precautions. Only use accessories and attachments

approved by Jacobsen.

5. Never direct discharge of material toward

bystanders, nor allow anyone near the machine

while in operation. The owner/operator is

responsible for injuries inflicted to bystanders and/or

damage to their property.

6. Use discretion when mowing near gravel areas

(roadway, parking areas, cart paths, etc.). Stones

discharged from the implement may cause serious

injuries to bystanders and/or damage the

equipment.

7. Always move reel levers to Off position to stop

blades when not mowing.

8. Move reel levers to Off position and raise the reels

when crossing paths or roadways. Look out for

traffic.

9. Stop and inspect the equipment for damage

immediately after striking an obstruction or if the

machine begins to vibrate abnormally. Have the

equipment repaired before resuming operation.

10. Slow down and use extra care on hillsides. Read

Section 6.7. Use caution when operating near drop

offs.

11. Look behind and down before backing up to be sure

the path is clear. Use care when approaching blind

corners, shrubs, trees, or other objects that may

obscure vision.

12. Never use your hands to clean cutting units. Use a

brush to remove grass clippings from blades. Blades

are extremely sharp and can cause serious injuries.

WARNING

A Roll Over Protection Structure (ROPS) is included with this mower. Seat belts must be worn whenever operating

a mower with a ROPS. Always keep seat belt snugly adjusted. DO NOT use seat belts on a mower without a ROPS.

If the mower is overturning, hold onto the steering wheel. Do not attempt to jump out or leave the seat.

CAUTION

To help prevent injury, always wear safety glasses, leather work shoes or boots, a hard hat, and ear protection.

NOTICE

To prevent damage to the reel and bedknife never

operate the reels when they are not cutting grass.

Excessive friction and heat will develop between the

bedknife and reel and damage the cutting edge.

CAUTION

Before mowing, pick up all debris such as rocks, toys,

and wire which can be thrown by the machine. Enter a

new area cautiously. Always operate at speeds that

allow you to have complete control of the mower.

WARNING

Before you clean, adjust, or repair this equipment,

always disengage all drives, lower implements to

the ground, engage parking brake, stop engine,

and remove key from ignition switch to prevent

injuries.

6 OPERATION

6.4 STARTING _______________________________________________________________

IMPORTANT: Do not use starting assist fluids. Use of

such fluids in the air intake system may be potentially

explosive or cause a “Runaway” engine condition and

could result in serious engine damage.

1. Make sure fuel shut off valve is completely open and

the tow valve is closed.

2. Sit in operator’s seat, make sure the reel levers (A)

are OFF, parking brake (B) is engaged and traction

lever (C) is in Neutral.

3. Move throttle lever (P) between 1/8 to 1/2 throttle.

Turn ignition switch (F) to RUN

4. Push glow plug switch (S) forward for 5 seconds

maximum, then release the switch. The colder the

temperature, the longer it will take to energize the

glow plugs.

5. Turn Ignition switch to START position and release

as soon as engine starts. Do not hold the key in the

start position for more than 15 seconds.

6. Allow the engine to become warm and properly

lubricated before operating at high RPM.

Figure 6A

6.5 STOPPING / PARKING _____________________________________________________

To stop:

Remove your foot from accelerator pedal. The mower will

automatically brake when the accelerator pedal returns to

Neutral. Always engage the parking brake before leaving

your machine.

To park the mower under normal conditions:

1. Disengage the reel control levers, raise the

implements, and move away from the area of

operation.

2. Select a flat and level area to park.

a. Release accelerator pedal to bring the mower to

a complete stop.

b. Disengage all drives, lower implements to the

ground, reduce throttle to slow, and allow engine

to operate at no load for a minute.

3. Engage parking brake, stop the engine, and always

remove the ignition key.

If an emergency arises and the mower must be parked in

the area of operation, follow the guidelines outlined by

the grounds superintendent. If the mower is parked on an

incline, chock or block the wheels.

3-5

Leht laadib ...

Ransomes 62304, 62379 Omaniku manuaal

Bränd: Ransomes

Mudel: 62304, 62379

Kategooria: Muruniidukid

Tüüp: Omaniku manuaal

Laadige alla PDF

aruanne

teistes keeltes

English: Ransomes 62304, 62379 Owner's manual

Ransomes 62304, 62379 Omaniku manuaal

Ransomes 62304, 62379 Omaniku manuaal

teistes keeltes

Seotud paberid

Muud dokumendid