Husqvarna LC 247i Kasutusjuhend

Tüüp
Kasutusjuhend
LC 247i, LC 347iVX, LC 353iVX
EN Operator's manual 8-24
BG Ръководство за експлоатация 25-44
CS Návod k použití 45-62
DA Brugsanvisning 63-79
DE Bedienungsanweisung 80-98
EL Οδηγίες χρήσης 99-117
ES Manual de usuario 118-136
ET Kasutusjuhend 137-153
FI Käyttöohje 154-170
FR Manuel d'utilisation 171-189
HR Priručnik za korištenje 190-206
HU Használati utasítás 207-224
IT Manuale dell'operatore 225-242
JA 取扱説明書 243-259
LT Operatoriaus vadovas 260-277
LV Lietošanas pamācība 278-295
NL Gebruiksaanwijzing 296-313
NO Bruksanvisning 314-330
PL Instrukcja obsługi 331-349
PT Manual do utilizador 350-367
RO Instrucţiuni de utilizare 368-385
RU Руководство по эксплуатации 386-405
SK Návod na obsluhu 406-423
SL Navodila za uporabo 424-440
SR Priručnik za rukovaoca 441-458
SV Bruksanvisning 459-475
TR Kullanım kılavuzu 476-492
UK Посібник користувача 493-512
ZH 操作手册 513-526
2
3
1
1
1016 28 17
11
14
26 20
21
22
23
24
15
2
3
4
5
18
12
12
9
7
8
LC 347iVX
LC 353iVX LC 247i
13
19
6
25 27
1
2 3 4 5 6 7
8 9 10 11 12 13
14 15
16 17
18 19
20 21
22 23
24 25
26 27
28 29
30 31
32
B
A
33
34 35
36 37
38
B
A
39
40 41
42 43
44 45
46 47
48 49
50 51
Contents
Introduction..................................................................... 8
Safety..............................................................................9
Assembly...................................................................... 14
Operation...................................................................... 14
Maintenance................................................................. 17
Troubleshooting............................................................ 19
Transportation, storage and disposal........................... 20
Technical data.............................................................. 21
Declaration of Conformity............................................. 24
Registered trademarks................................................. 24
Introduction
Product description
The product is a pedestrian-controlled rotary lawn
mower. The grass is collected in a grass catcher.
Remove the grass catcher to get rear discharge of the
grass. Attach a mulch kit (accessory) to cut the grass
into fertilizer.
Intended use
Use the product to cut grass. Do not use the product for
other tasks.
Product overview
(Fig. 1)
1. Control panel (LC 347iVX, LC 353iVX)
2. Motor brake handle
3. Start inhibitor
4. Grass catcher
5. Rear cover
6. Safety key
7. Handle knob
8. Battery cover
9. Cutting height control
10. ON/OFF button
11. Indicator for
Bluetooth®
wireless technology
12. Lift handles
13. SavE indicator
14. Battery indicator
15. Speed level indicator (LC 347iVX, LC 353iVX)
16. Decrease speed button (LC 347iVX, LC 353iVX)
17. Increase speed button (LC 347iVX, LC 353iVX)
18. Symbols
19. Cutting cover
20. Operator's manual
21. Rating plate
22. Drive bail (LC 347iVX, LC 353iVX)
23. Battery charger (Accessory)
24. Battery (Accessory)
25. Error LED (LC 247i)
26. Error LED (LC 347iVX, LC 353iVX)
27. SavE button (LC 247i)
28. SavE button (LC 347iVX, LC 353iVX)
Symbols on the product
(Fig. 2) WARNING
(Fig. 3) Read the instructions.
(Fig. 4) WARNING - Beware of thrown objects.
(Fig. 5) Keep bystanders away.
(Fig. 6) WARNING – Keep hands and feet away
from the blades.
(Fig. 7) WARNING – Disconnect battery before
maintenance.
(Fig. 8) The product or package of the product is
not domestic waste. Recycle it at a
recycling station for electrical and
electronic equipment.
(Fig. 9) The product agrees with applicable EC
directives.
(Fig. 10) Noise emission to the environment label
as per EU and UK directives and
regulations. The guaranteed sound power
level of the product is specified in
Technical data on page 21
and on the
label.
(Fig. 11) The product is drip protected.
(Fig. 12) Release the motor brake handle to stop.
(Fig. 13) Scannable code
Note: Other symbols/decals on the product refer to
certification requirements for some markets.
81696 - 002 - 03.12.2021
Label on the product
(Fig. 14)
DANGER – Keep hands and feet away.
Product liability
As referred to in the product liability laws, we are not
liable for damages that our product causes if:
the product is incorrectly repaired.
the product is repaired with parts that are not from
the manufacturer or not approved by the
manufacturer.
the product has an accessory that is not from the
manufacturer or not approved by the manufacturer.
the product is not repaired at an approved service
center or by an approved authority.
Safety
Safety definitions
Warnings, cautions and notes are used to point out
specially important parts of the manual.
WARNING: Used if there is a risk of
injury or death for the operator or bystanders
if the instructions in the manual are not
obeyed.
CAUTION: Used if there is a risk of
damage to the product, other materials or
the adjacent area if the instructions in the
manual are not obeyed.
Note: Used to give more information that is necessary
in a given situation.
General product safety warnings
WARNING: Read all safety warnings,
instructions, illustrations and specifications
provided with this product. Failure to follow
all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "product" in the warnings refers to your mains-
operated (corded) product or battery-operated (cordless)
product.
Work area safety
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate the product in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. The product create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while operating
the product. Distractions can cause you to lose
control.
Electrical safety
Product plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) products. Unmodified plugs
and matching outlets will reduce risk of electric
shock.
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose products to rain or wet conditions.
Water entering a product will increase the risk of
electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the product. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
When operating a product outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
If operating a product in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Personal safety
Stay alert, watch what you are doing and use
common sense when operating a product. Do not
use a product while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating products may result in
serious personal injury.
Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the
product. Carrying products with your finger on the
switch or energising products that have the switch on
invites accidents.
Remove any adjusting key or wrench before turning
the product on. A wrench or a key left attached to a
rotating part of the product may result in personal
injury.
1696 - 002 - 03.12.2021 9
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the
product in unexpected situations.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
Do not let familiarity gained from frequent use of
products allow you to become complacent and
ignore product safety principles. A careless action
can cause severe injury within a fraction of a second.
Product use and care
Do not force the product. Use the correct product for
your application. The correct product will do the job
better and safer at the rate for which it was
designed.
Do not use the product if the switch does not turn it
on and off. Any product that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or
remove the battery pack, if detachable, from the
product before making any adjustments, changing
accessories, or storing products. Such preventive
safety measures reduce the risk of starting the
product accidentally.
Store idle products out of the reach of children and
do not allow persons unfamiliar with the product or
these instructions to operate the product. Products
are dangerous in the hands of untrained users.
Maintain products and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
product's operation. If damaged, have the product
repaired before use. Many accidents are caused by
poorly maintained products.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Use the product, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the product for operations
different from those intended could result in a
hazardous situation.
Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the product in unexpected situations.
Service
Have your product serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the product is
maintained.
Never service damaged battery packs. Service of
battery packs should only be performed by the
manufacturer or authorized service providers.
Battery tool use and care
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
Use products only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from
the battery may cause irritations or burns.
Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion or
risk of injury.
Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or
temperature above 130 °C / 265 °F may cause
explosion.
Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified
range may damage the battery and increase the risk
of fire.
Lawnmower safety warnings
Do not use the lawnmower in bad weather
conditions, especially when there is a risk of
lightning. This decreases the risk of being struck by
lightning.
Thoroughly inspect the area for wildlife where the
lawnmower is to be used. Wildlife may be injured by
the lawnmower during operation.
Thoroughly inspect the area where the lawnmower is
to be used and remove all stones, sticks, wires,
bones, and other foreign objects. Thrown objects
can cause personal injury.
Before using the lawnmower, always visually inspect
to see that the blade and the blade assembly are not
worn or damaged. Worn or damaged parts increase
the risk of injury.
Before use, check the supply cord and any extension
cord for signs of damage or aging. Do not use the
lawnmower if the cord is damaged or worn. If the
cord is damaged or worn during use, switch off the
lawnmower and do not touch the cord before
disconnecting it from the supply. A damaged supply
10 1696 - 002 - 03.12.2021
cord or extension cord may result in electric shock,
fire and/or serious injury.
Check the grass catcher frequently for wear or
deterioration. A worn or damaged grass catcher may
increase the risk of personal injury.
Keep guards in place. Guards must be in working
order and be properly mounted. A guard that is
loose, damaged, or is not functioning correctly may
result in personal injury.
Keep all cooling air inlets clear of debris. Blocked air
inlets and debris may result in overheating or risk of
fire.
While operating the lawnmower, always wear non-
slip and protective footwear. Do not operate the
lawnmower when barefoot or wearing open sandals.
This reduces the chance of injury to the feet from
contact with the moving blade.
While operating the lawnmower, always wear long
trousers. Exposed skin increases the likelihood of
injury from thrown objects.
Do not operate the lawnmower in wet grass. Walk,
never run. This reduces the risk of slipping and
falling which may result in personal injury.
Do not operate the lawnmower on excessively steep
slopes. This reduces the risk of loss of control,
slipping and falling which may result in personal
injury.
When working on slopes, always be sure of your
footing, always work across the face of slopes, never
up or down and exercise extreme caution when
changing direction. This reduces the risk of loss of
control, slipping and falling which may result in
personal injury.
Use extreme caution when reversing or pulling the
lawnmower towards you. Always be aware of your
surroundings. This reduces the risk of tripping during
operation.
Keep the supply cord away from the cutting blades.
A damaged supply cord may result in electric shock,
fire and/or serious injury.
Switch off and remove plug from mains if the cord is
entangled or damaged. Entangled or damaged cords
can increase the risk of electric shock.
Do not touch blades and other hazardous moving
parts while they are still in motion. This reduces the
risk of injury from moving parts.
When clearing jammed material or cleaning the
lawnmower, make sure all power switches are off
and the power cord is disconnected. Unexpected
operation of the lawnmower may result in serious
personal injury.
Residual current device
Use a residual current device with a tripping current
of maximum 30 mA.
General safety instructions
WARNING: Read the warning
instructions that follow before you use the
product.
This product is dangerous if used incorrectly or if you
are not careful. Injury or death can occur if you do
not obey the safety instructions.
This product produces an electromagnetic field
during operation. This field may under some
circumstances interfere with active or passive
medical implants. To reduce the risk of serious or
fatal injury we recommend persons with medical
implants to consult their physician and the medical
implant manufacturer before operating this product.
Always be careful and use your common sense. If
you are not sure how to operate the product in a
special situation, stop and speak to your Husqvarna
dealer before you continue.
Keep in mind that the operator will be held
responsible for accidents that involve other persons
or their property.
Keep the product clean. Make sure that you can
clearly read signs and decals.
Never allow children or people unfamiliar with these
instructions to use the appliance. Local regulations
may restrict the age of the operator.
Always monitor a person, with decreased physical
capacity or mental capacity, that uses the product. A
responsible adult must be there at all times.
Do not use the product if you are tired, ill, or under
the influence of alcohol, drugs or medicine. This has
a negative effect on your vision, alertness,
coordination and judgment.
Do not use the product if it is defective.
Do not change this product or use it if it is possible
that it has been changed by others.
Work safety
WARNING: Read the warning
instructions that follow before you use the
product.
Use this product to cut grass lawns only. It is not
permitted to use it for other tasks.
Use personal protective equipment. Refer to
Personal protective equipment on page 12
.
Make sure that you know how to stop the motor
quickly in an emergency.
Do not operate the product in rain or wet conditions.
The risk of electrical shock increases if water enters
the product.
Do not operate the product unless the blade and all
covers are attached correctly. An incorrectly
attached blade can come loose and cause personal
injury.
1696 - 002 - 03.12.2021 11
Make sure that the blade does not hit objects such
as stones and roots. This can do damage to the
blade and bend the motor shaft. A bent axle causes
heavy vibration and a very high risk that the blade
becomes loose.
If the blade hits an object or if vibrations occur, stop
the product immediately. Stop the motor, turn the
safety key to 0 and remove the battery. Wait until
moving parts stop. Examine the product for
damages. Tighten loose parts. Repair damages and
replace damaged parts. Let an approved service
agent do the repair.
Never attach the motor brake handle permanently to
the handle when the motor is started.
Put the product on a stable, flat surface and start it.
Make sure that the blade does not hit the ground or
other objects.
Always stay behind the product when you operate it.
Let all the wheels stay on the ground and keep 2
hands on the handle when you operate the product.
Keep your hands and feet away from the rotating
blades.
Do not tilt the product when you start the motor or
during operation of the product.
Be careful when you pull the product rearward.
Never lift up the product when the motor is started. If
you must lift the product, first stop the motor, turn the
safety key to 0 and remove the battery.
Do not walk rearward when you operate the product.
Stop the motor when it is necessary to tilt the
product for transportation or before you move across
areas without grass, for example paths made of
gravel, stone and asphalt.
Do not run with the product when the motor is
started. Always walk when you operate the product.
Stop the motor before you change the cutting height.
Never make adjustments with the motor started.
Never let the product stay out of view with the motor
started. Stop the motor and make sure that the
cutting equipment does not rotate.
The vibrations in the product during operation can be
different from the declared vibration value in
Technical data on page 21
. The difference is
caused by variations in how the product is used. If
you operate the product frequently or for long
periods of time, take breaks regularly to prevent
injury from vibrations.
Safety instructions for operation
Personal protective equipment
WARNING: Read the warning
instructions that follow before you use the
product.
Personal protective equipment cannot fully prevent
injury but it decreases the degree of injury if an
accident does occur. Let your dealer help you select
the right equipment.
Use heavy-duty slip-resistant boots or shoes. Do not
use open shoes or go with bare feet.
Use heavy, long pants.
Use protective gloves when necessary, for example
when you attach, examine or clean the cutting
equipment.
We recommend to use hearing protection.
Safety devices on the product
WARNING: Read the warning
instructions that follow before you use the
product.
Do not use a product with defective safety devices.
Do not remove or do modifications to safety devices.
Do a check of the safety devices regularly. If the
safety devices are defective, speak to your
Husqvarna service agent.
To do a check of the cutting cover
The cutting cover decreases vibrations in the product
and decreases the risk of injury from the blade.
Examine the cutting cover to make sure that there
are no damages such as cracks.
To do a check of the safety key
The safety key is below the battery lid. The safety key
connects the battery that supplies the motor with power.
Start and stop the motor to do a check of the safety
key.
If the safety key operates correctly, the motor can
only start when the safety key is in position 1. (Fig.
15)
To do a check of the motor brake handle
The motor brake handle stops the motor. When the
motor brake handle is released, the motor stops.
Start the product. Refer to
Operation on page 14
.
Release the motor brake handle. (Fig. 16)
Make sure that the product stops. If the motor does
not stop in 3 seconds, let an approved Husqvarna
service agent adjust the motor brake.
To do a check of the start inhibitor
Do a check of the start inhibitor to make sure that it
prevents operation of the motor.
1. Push the motor brake handle in the direction of the
handlebar. The start inhibitor stops the movement.
2. Push the start inhibitor out. (Fig. 17)
3. Release the start inhibitor and make sure that it goes
back to its initial position.
12 1696 - 002 - 03.12.2021
Battery safety
WARNING: Read the warning
instructions that follow before you use the
product.
Use Husqvarna rechargeable batteries as a power
supply for related Husqvarna products only. To
prevent injury, do not use the battery as a power
supply for other devices.
Do not use non-rechargeable batteries.
Risk of electrical shock. Do not connect the battery
terminals to keys, coins, screws or other metal. This
can cause a short circuit of the battery.
Do not put objects into the air slots of the battery.
Keep the battery away from sunlight, heat or open
flame. The battery can explode and cause burns
and/or chemical burns.
Keep the battery away from rain and wet conditions.
Keep the battery away from microwaves and high
pressure.
Do not try to disassemble or break the battery.
If the battery leaks, do not let the liquid touch your
body or eyes. If you have touched the liquid, clean
the area with a large quantity of water and get
medical aid.
Use the battery in the product only when the ambient
temperature is between 5 °C - 40 °C.
Use the battery charger only when the ambient
temperature is between 5 °C - 40 °C.
The battery will not charge if the battery temperature
is more than 50 ° C.
Do not clean the battery or the battery charger with
water. Refer to
To clean the battery and the battery
charger on page 18
.
Do not use a defective or damaged battery.
Keep batteries in storage away from metal objects
such as nails, coins, jewellery.
Battery charger safety
WARNING: Read the warning
instructions that follow before you use the
product.
Use the QC battery chargers to charge Husqvarna
replacement batteries only.
Risk of electrical shock or short circuit. Do not put
objects into the air slots of the charger. Do not try to
disassemble the battery charger. Do not connect the
charger terminals to metal objects. Use an approved
mains socket.
This product produces an electromagnetic field
during operation. This field may under some
circumstances interfere with active or passive
medical implants. To reduce the risk of serious or
fatal injury, we recommend persons with medical
implants to consult their physician and the medical
implant manufacturer before operating this product.
Regularly make sure that the power cord of the
battery charger is not damaged and that there are no
cracks in it.
Do not lift the battery charger by the power cord. To
disconnect the battery charger from a mains socket,
pull out the plug. Do not pull the power cord.
Keep the power cord and extension cables away
from water, oil and sharp edges. Make sure that the
cable is not pinched in doors, fences or equivalent. It
can cause the charger to become energized.
Do not clean the battery charger with water.
The battery charger can be used by children aged
from 8 years and above and persons with reduced
physical, sensory, or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
battery charger in a safe way and understand the
hazards involved. Children shall not play with the
battery charger. Cleaning and user maintenance
shall not be made by children without supervision.
Do not charge non-rechargeable batteries in the
battery charger.
Do not use the battery charger near flammable
materials or materials that can cause corrosion. Do
not cover the battery charger. Pull out the plug to the
battery charger if there is smoke or fire.
Do not use a defective or damaged battery charger.
Only charge the battery indoors in a room with good
airflow and away from sunlight. Do not charge the
battery in wet conditions.
Safety instructions for maintenance
WARNING: Read the warning
instructions that follow before you use the
product.
To prevent accidental start during maintenance, turn
the safety key to 0 and remove the battery. Wait at
minimum 5 seconds before you start the
maintenance.
Only do the maintenance work written in this
operator's manual. More extensive work and
professional repairs must be done by an approved
service agent. Speak to your nearest service agent
for more information.
Do the maintenance work correctly to increase the
lifetime of the product and decrease the risk of
accidents.
Replace damaged, worn or broken parts. Always use
original spare parts from the manufacturer. Other
spare parts can cause damage to the product and
increase the risk of accidents.
To prevent injury, do not remove or do modifications
to safety devices.
1696 - 002 - 03.12.2021 13
Put on heavy duty gloves when you use the cutting
equipment. The blade is very sharp and cuts can
easily occur.
Keep the cutting edges sharp and clean for the best
and safest performance.
Let your service agent regularly examine the product
and make necessary adjustments and repairs.
Obey the instructions for how to change accessories.
Only use accessories from the manufacturer.
When not in operation, keep the product, battery and
battery charger apart in a dry, indoor and locked
area. Make sure that children and persons that are
not approved cannot get access to the product,
battery or battery charger.
Assembly
Introduction
WARNING: Before you assemble the
product, read the safety chapter.
WARNING: To prevent accidental start
during assembly, turn the safety key to 0,
remove the battery and wait at minimum 5
seconds.
To adjust the handle
1. Loosen the lower knobs.
2. Move the knobs to the lower end of the grooves on
the left and the right side of the product. (Fig. 18)
3. Set the handle height in one of the 2 available
positions.
4. Move the knobs up in the direction of the handle until
they stop and you hear a click. (Fig. 19)
5. Tighten the knobs fully.
To assemble the grass catcher
1. Attach the grass catcher frame to the grass bag with
the rigid part of the bag on the bottom. Keep the
handle of the frame on top of the grass bag. (Fig. 20)
2. Attach the bottom section of the grass catcher frame
in the groove on the bottom of the grass catcher.
3. Attach the grass bag to the grass catcher frame with
the clips. (Fig. 21)
4. Lift the rear cover.
5. Attach the grass catcher to the top edge of the
chassis.
6. Put the lower part of the grass catcher into the grass
discharge channel. (Fig. 22)
To assemble the mulch plug
(accessory)
1. Lift up the rear cover and remove the grass catcher.
2. Put the mulch plug into the discharge channel. (Fig.
23)
3. Replace the blade with the mulch blade that is
supplied in the mulch kit. Refer to
To replace the
blade on page 18
.
Operation
Introduction
WARNING: Before you operate the
product, you must read and understand the
safety chapter.
Husqvarna Connect
Husqvarna Connect is a free app for your mobile device.
The Husqvarna Connect app gives extended functions
for your Husqvarna product:
Extended product information.
Information about, and help with, product parts and
servicing.
To start to use Husqvarna Connect
1. Download the Husqvarna Connect app on your
mobile device.
2. Register in the Husqvarna Connect app.
3. Follow the instruction steps in the Husqvarna
Connect app to connect and register the product.
Note: Husqvarna Connect app is not available for
download in all markets. Speak to your servicing
dealer for more information.
14 1696 - 002 - 03.12.2021
Bluetooth® information (LC 347iVX,
LC 353iVX)
Bluetooth® wireless technology
The symbol for
Bluetooth®
wireless technology comes
on when your mobile device is connected to the product.
(Fig. 24)
To set the product in operation position
1. Fold the handle to upright position. (Fig. 25)
2. Move the knobs up in the direction of the handle until
they stop and you hear a click. (Fig. 19)
3. Tighten the knobs fully.
WARNING: Do not operate the product
unless the handle is fully folded up and set
in one of the applicable height positions.
Refer to
To adjust the handle on page 14
.
To set the cutting height
The cutting height can be adjusted in 6 levels.
1. Move the cutting height lever down to decrease the
cutting height.
2. Move the cutting height lever up to increase the
cutting height. (Fig. 26)
CAUTION: Do not set the cutting height
too low. The blades can hit the ground if the
surface of the lawn is not level.
Battery
WARNING: Before you use the battery,
you must read and understand the safety
chapter. You must also read and understand
the operator's manual for the battery and the
battery charger.
Keep the battery and the battery charger in correct
ambient temperatures.
Ambient temperature
Operation of the bat-
tery
5 °C - 40 °C
Charging of the bat-
tery
5 °C - 40 °C
Battery status
The display shows the remaining battery capacity and if
there are problems with the battery. The battery capacity
is shown for 5 seconds after the product is switched off
or the battery indicator button is pressed. The warning
symbol on the battery is on when an error has occurred.
See
Battery on page 19
.
(Fig. 27)
LED lights Battery status
All LEDs are lit Fully charged (75-100%)
LED 1, LED 2, LED 3 are
lit
The battery is 50%-75%
charged
LED 1, LED 2 are lit The battery is 25%-50%
charged
LED 1 is lit The battery is 0%-25%
charged.
LED 1 flashes The battery is empty.
Charge the battery.
To charge the battery
Charge the battery before the first use. The battery is
only 30% charged when supplied to the customer.
Note: The battery charger must be connected to the
voltage and frequency specified on the rating plate.
The battery does not charge if the battery temperature is
above 50°C. The battery charger decreases the
temperature of the battery before it starts to charge.
1. Connect one end of the power cord for the battery
charger into the socket of the battery charger.
2. Connect the other end of the power cord for the
battery charger in an grounded mains socket. The
LED on the battery charger flashes green one time.
(Fig. 28)
3. Put the battery in the battery charger. The green light
on the charger comes on when the battery is
correctly connected to the battery charger. (Fig. 29)
4. When all LEDs on the battery have come on the
battery is fully charged. Charge the battery for
maximum 24 hours.
5. To disconnect the battery charger from the mains
socket, pull the plug, not the power cord.
6. Remove the battery from the battery charger.
Battery charging status
A Husqvarna Li-ion battery can be charged or used at all
charging levels. The battery is not damaged. A fully
charged battery will not decrease its charge when the
battery is left in the charger.
LED display Charging status
LED 1 flashes 0%-25%
LED 1 is lit, LED 2 flashes 25%-50%
1696 - 002 - 03.12.2021 15
LED display Charging status
LED 1, LED 2 are lit, LED
3 flashes
50%-75%
LED 1, LED 2, LED 3 are
lit, LED 4 flashes
75%-100%
LED 1, LED 2, LED 3,
LED 4 are lit
Fully charged
To start the product (LC 247i)
1. Open the battery lid.
2. Put a charged battery in 1 of the battery holders. For
longer operation time, put a second charged battery
in the other battery holder.
3. Turn the safety key to 1. (Fig. 30)
4. Stay behind the product.
5. Loosen the start inhibitor. (Fig. 17)
6. Push the motor brake handle in the direction of the
handlebar. (Fig. 31)
To start the product (LC 347iVX,
LC 353iVX)
1. Open the battery lid.
2. Put a charged battery in 1 of the battery holders. For
longer operation time, put a second charged battery
in the other battery holder.
3. Turn the safety key to 1. (Fig. 32)
4. Stay behind the product.
5. Push the ON/OFF button (A) on the control panel.
The display comes on. The battery indicator (B)
shows the battery charge of the 2 batteries. The
number of the battery that operates is shown
adjacent to the battery indicator. For models
LC 347iVX, LC 353iVX, the display also shows the
set speed. (Fig. 33)
6. Loosen the start inhibitor. (Fig. 34)
7. Push the motor brake handle in the direction of the
handlebar. (Fig. 35)
To use the drive on the wheels
LC 347iVX, LC 353iVX
Pull the drive bail in the direction of the handlebar to
start the drive. (Fig. 36)
Push + and - on the control panel to set the drive
speed in 4 steps. (Fig. 37)
Release the drive bail to disengage the drive, for
example when you go near an obstacle.
To use the SavE function (LC 247i)
The product has a battery saving function (SavE) that
gives longer operation time.
Push the SavE button to position 1 to start the
function. (Fig. 38)
Push the SavE button to position 0 to stop the
function.
Note: The SavE function stops automatically if the
ground conditions make it necessary to have a higher
output. The SavE function starts automatically again
when the ground conditions let it.
To use the SavE function
(LC 347iVX, LC 353iVX)
The product has a battery saving function (SavE) that
gives longer operation time.
1. Push the SavE button (A) to start the function. The
SavE symbol (B) on the display comes on.
2. Push the SavE button again to stop the function.
The SavE symbol (B) on the display goes out. (Fig.
39)
Note: The SavE function stops automatically if the
ground conditions make it necessary to have a higher
output. The SavE function starts automatically again
when the ground conditions let it.
High load function
When the product cuts long or wet grass, the motor
automatically increases rpm. The motor goes back to
standard mode when high load is not necessary.
Automatic restart
During operation, the blade and motor can temporarily
stop because of obstacles such as grass blockage
below the cutting cover. If this occurs and you keep the
motor brake handle pushed down, the product tries to
restart automatically. If the product does not restart in 5
seconds, it can be necessary to clean below the cutting
cover. Refer to
To clean the product on page 18
.
WARNING: Before a check of the
cutting cover, release the motor brake
handle, turn the safety key to 0, remove the
battery and wait at minimum 5 seconds.
There is a risk of injury if the obstacle is
removed and the product accidentally starts.
To stop the product (LC 247i)
WARNING: Turn the safety key to 0
before you let the product out of view.
1. Release the motor brake handle to stop the motor.
(Fig. 40)
2. Open the battery lid and turn the safety key to 0.
(Fig. 41)
16 1696 - 002 - 03.12.2021
3. To remove the battery, push the 2 release buttons
and pull out the battery. (Fig. 42)
4. Charge the battery if it is weak. For more
information, refer to
To charge the battery on page
15
.
To stop the product (LC 347iVX,
LC 353iVX)
WARNING: Turn the safety key to 0
before you let the product out of view.
1. Release the motor brake handle to stop the motor.
(Fig. 43)
2. Push the ON/OFF button on the control panel. All
LED lights and symbols on the display go out. (Fig.
44)
3. Open the battery lid and turn the safety key to 0.
(Fig. 45)
4. To remove the battery, push the 2 release buttons
and pull out the battery. (Fig. 46)
5. Charge the battery if it is weak. For more
information, refer to
To charge the battery on page
15
.
Note: The product is automatically de-energized if you
do not operate it for some minutes. To start the product
again, refer to
To start the product (LC 347iVX,
LC 353iVX) on page 16
.
To get a good result
Always use a sharp blade. A blunt blade gives an
irregular result and the cut surface of the grass
becomes yellow. A sharp blade also uses less
energy than a blunt blade.
Do not cut more than ⅓ of the length of the grass.
Cut first with the cutting height set high. Examine the
result and lower the cutting height to an applicable
level. If the grass is very long, drive slowly and cut 2
times if necessary.
Cut in different directions each time to prevent
stripes in the lawn.
Keep the cutting cover clean. Buildup from grass and
dirt on the inner side of the cutting cover can
decrease the cutting result. Refer to
To clean the
product on page 18
.
To cut grass without a grass catcher or
mulch plug attached
Lift up the rear cover and remove the grass catcher.
If a mulch plug and a mulch blade are attached,
remove them.
Close the rear cover before you operate the product.
When you operate the product, the cut grass discharges
below the rear cover.
Maintenance
Introduction
WARNING: Before you do
maintenance, you must read and
understand the safety chapter.
For all servicing and repair work on the product, special
training is necessary. We guarantee the availability of
professional repairs and servicing. If your dealer is not a
service agent, speak to them for information about the
nearest service agent.
For more detailed information, refer to
www.husqvarna.com.
Maintenance schedule
The maintenance intervals are calculated from daily use
of the product. The intervals change if the product is not
used daily.
For maintenance identified with * see instructions in
Safety on page 9
.
Each use Monthly Each
season
Do a general inspection X
Clean the product X
Do a check of the start inhibitor * X
Make sure that the safety devices on the product are not defective * X
Examine the cutting equipment X
Examine the cutting cover * X
1696 - 002 - 03.12.2021 17
Each use Monthly Each
season
Do a check of the motor brake handle * X
Make sure that the ON/OFF button operates correctly and is not defective X
Examine the battery for damage X
Do a check of the battery charge X
Make sure that the release buttons on the battery operates correctly and that the
battery locks into the product X
Examine the battery charger for damage and make sure that it operates correct-
ly. X
Examine the connections between the battery and the product. Also examine the
connection between the battery and the battery charger. X
To do a general inspection
Make sure that the nuts and screws on the product
are tightened.
Make sure that the cables on the product are not in a
position where they can get damaged.
To clean the product
Clean plastic parts with a clean and dry cloth.
Do not use water to clean the product. Water can
enter the battery or the motor and cause short circuit
or damage to the product.
Do not use a high pressure washer to clean the
product.
Do not flush water directly on the motor.
Use a brush to remove leaves, grass and dirt.
To clean the battery and the battery
charger
WARNING: Do not clean the battery or
the battery charger with water.
Make sure that the battery and the battery charger
are clean and dry before you put the battery into the
battery charger.
Clean the battery terminals with compressed air or
use a soft and dry cloth.
Clean the surfaces of the battery and the battery
charger with a soft and dry cloth.
To examine the cutting equipment
WARNING: To prevent accidental start,
turn the safety key to 0, remove the battery
and wait a minimum 5 seconds.
WARNING: Use protective gloves
when you do maintenance on the cutting
equipment. The blade is very sharp and cuts
can easily occur.
1. Examine the cutting equipment for damage or
cracks. Always replace a damaged cutting
equipment.
2. Look at the blade to see if it is damaged or blunt.
Note: It is necessary to balance the blade after it is
sharpened. Let a service center sharpen, replace and
balance the blade. If you hit an obstacle that causes the
product to stop, replace the damaged blade. Let the
service center estimate if the blade can be sharpened or
must be replaced.
To replace the blade
Refer to
Technical data on page 21
for the correct type
of blade.
WARNING: Lock the blade with a block
of wood to prevent injury to fingers when
you replace the blade. The blade can be
moved when the motor is off and fingers can
become trapped between the blade and
stationary parts.
1. Lock the blade with a block of wood. (Fig. 47)
2. Remove the blade bolt.
3. Remove the blade.
4. Examine the blade support and blade bolt to see if
there are damages.
5. Examine the motor shaft to make sure that it is not
bent.
6. When you attach the new blade, point the angled
ends of the blade in the direction of the cutting cover.
(Fig. 48)
18 1696 - 002 - 03.12.2021
7. Make sure that the blade is aligned with the center of
the motor shaft.
8. Lock the blade with a block of wood. Attach the
spring washer and tighten the bolt and washer with a
torque of 23–28 Nm. (Fig. 49)
9. Pull the blade around by hand and make sure that it
turns freely.
WARNING: Use heavy duty gloves.
The blade is very sharp and cuts can
easily occur.
10. Start the product to do a test of the blade. If the
blade is not correctly attached, there is vibration in
the product or the cutting result is unsatisfactory.
Troubleshooting
Battery
LED on the battery Cause Solution
The green LED flashes. The battery voltage is low. Charge the battery. Refer to
To charge the battery
on page 15
.
The error LED flashes. The battery is weak. Charge the battery. Refer to
To charge the battery
on page 15
.
The temperature in the work environ-
ment is too high or too low.
Use the battery in temperatures between 5 °C - 40
°C.
Overvoltage. Make sure that the mains voltage is the same as
on the rating plate on the product.
Remove the battery from the battery charger. Wait
5 seconds and try again to charge the battery. If
the problem continues, speak to an approved
service agent.
The error LED is on. The cell difference too much (1V). Speak to an approved service agent.
Battery charger
LED on the battery
charger
Cause Solution
The error LED flash-
es.
The temperature in the work en-
vironment is too high or too low.
Use the battery charger in temperatures between 5 °C -
40 °C.
The error LED is on. Speak to an approved service agent.
Lawn mower
The warning indicator (error LED) is found below the
battery lid ((LC 247i)) or on the control panel
((LC 347iVX, LC 353iVX)).
1696 - 002 - 03.12.2021 19
Problem Error LED (number
of flashes)
Cause Solution
Error LED flashes.
The product does
not operate cor-
rectly.
3 The blade is blocked. Turn the safety key to 0 to prevent acci-
dental start. Remove the battery and
wait a minimum of 5 seconds. Remove
possible obstacles and make sure that
the blade can rotate freely. If the prob-
lem continues, speak to an approved
service agent.
5 The motor speed drops too
much, and the motor stops.
Increase the cutting height. Refer to
To
set the cutting height on page 15
.
61The wheels or transmission is
blocked.
Turn the safety key to 0 to prevent acci-
dental start. Remove the battery and
wait a minimum of 5 seconds. Remove
the possible obstacles and make sure
that the wheels can rotate freely. If the
problem continues, speak to an ap-
proved service agent.
10 The motor control is too hot. Stop the motor and wait until it has be-
come cool.
Error LED flashes.
The product stops.
0 Battery connector failure. Examine the battery connector.
3 There is overload in the mo-
tor.
Increase the cutting height. Refer to
To
set the cutting height on page 15
.
8 The battery is weak. Charge the battery. Refer to
To charge
the battery on page 15
.
9 Battery error or no signal from
battery.
Put the battery in the product correctly
and examine the battery connector. If the
error LED on the battery flashes. Refer
to
Battery on page 19
.
12 Incorrect start procedure. The
motor brake handle has been
engaged before the motor
starts.
Release the motor brake handle and
wait approximately 5 seconds. Push the
motor brake handle down again to start
the product.
Other errors. If other errors occur, turn the safety key to 0, remove the battery and speak to an approved
service agent.
Transportation, storage and disposal
Introduction
WARNING: To prevent unintentional
start during transport turn the safety key
to ”0”, remove the battery and wait at least 5
seconds.
To set the product in transport position
1. Loosen the lower knobs.
2. Move the knobs to the lower end of the grooves on
the left and the right side of the product. (Fig. 18)
3. Fold the handle forward. (Fig. 50)
4. Remove the grass catcher.
1LC 347iVX, LC353iVX
20 1696 - 002 - 03.12.2021
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416
  • Page 417 417
  • Page 418 418
  • Page 419 419
  • Page 420 420
  • Page 421 421
  • Page 422 422
  • Page 423 423
  • Page 424 424
  • Page 425 425
  • Page 426 426
  • Page 427 427
  • Page 428 428
  • Page 429 429
  • Page 430 430
  • Page 431 431
  • Page 432 432
  • Page 433 433
  • Page 434 434
  • Page 435 435
  • Page 436 436
  • Page 437 437
  • Page 438 438
  • Page 439 439
  • Page 440 440
  • Page 441 441
  • Page 442 442
  • Page 443 443
  • Page 444 444
  • Page 445 445
  • Page 446 446
  • Page 447 447
  • Page 448 448
  • Page 449 449
  • Page 450 450
  • Page 451 451
  • Page 452 452
  • Page 453 453
  • Page 454 454
  • Page 455 455
  • Page 456 456
  • Page 457 457
  • Page 458 458
  • Page 459 459
  • Page 460 460
  • Page 461 461
  • Page 462 462
  • Page 463 463
  • Page 464 464
  • Page 465 465
  • Page 466 466
  • Page 467 467
  • Page 468 468
  • Page 469 469
  • Page 470 470
  • Page 471 471
  • Page 472 472
  • Page 473 473
  • Page 474 474
  • Page 475 475
  • Page 476 476
  • Page 477 477
  • Page 478 478
  • Page 479 479
  • Page 480 480
  • Page 481 481
  • Page 482 482
  • Page 483 483
  • Page 484 484
  • Page 485 485
  • Page 486 486
  • Page 487 487
  • Page 488 488
  • Page 489 489
  • Page 490 490
  • Page 491 491
  • Page 492 492
  • Page 493 493
  • Page 494 494
  • Page 495 495
  • Page 496 496
  • Page 497 497
  • Page 498 498
  • Page 499 499
  • Page 500 500
  • Page 501 501
  • Page 502 502
  • Page 503 503
  • Page 504 504
  • Page 505 505
  • Page 506 506
  • Page 507 507
  • Page 508 508
  • Page 509 509
  • Page 510 510
  • Page 511 511
  • Page 512 512
  • Page 513 513
  • Page 514 514
  • Page 515 515
  • Page 516 516
  • Page 517 517
  • Page 518 518
  • Page 519 519
  • Page 520 520
  • Page 521 521
  • Page 522 522
  • Page 523 523
  • Page 524 524
  • Page 525 525
  • Page 526 526
  • Page 527 527
  • Page 528 528

Husqvarna LC 247i Kasutusjuhend

Tüüp
Kasutusjuhend