Snapper OP21507B Kasutusjuhend

Snapper
Bränd
Snapper
Mudel
OP21507B
Kategooria
Muruniidukid
Tüüp
Kasutusjuhend
Parts Manual fo
r
Revision 3,
21" STEEL DECK WALK BEHIND MOWER
SERIES 7
McDonough, GA, 30253 U.S.A.
TP 400-5143-3-WB-N
8/10/2007
Manual No. 7006051A
Copyright © 2007
Briggs & Startton Yard Power Products Group
Milwaukee, WI USA. All Rights Reserved
Briggs & Startton Corporation
PUSH MODELS PROPELLED
MODELS
21357B DP21357B
21407T DP21407
T
21407T-2 DP21407T-
2
21507B DP21507B
21507T DP21507BE
G23157B GP21507B
M21357B GP21507B
E
R21357B MP21357B
R21407
T
MP21507BE
R21507B OP21407T-2
R21507TV OP21507B
P21357B
P21407R-
2
P21407
T
P21407T-2
P21507B
P21507BE
P21507TV
PD21357B
RP21357B
RP21407
T
RP21507B
RP21507BE
RP21507TV
Table Of Content
s
TP 400-5143-3-WB-N
Manual No. 7006051A21" STEEL DECK WALK BEHIND MOWER
SERIES 7
3
PAGE GROUP
4
Handles & Controls
8
Cutting Deck, Blade, Interlock
10
Front Wheel Bracket, Latches
12
Rear Wheels, Brackets, Latches
14
Front Wheels
16
Rear Wheels
18
Drive System - Self Propelled
22
Transmission (Differential)
24
Throttle Controls - Series 7
26
Decals (Part 1)
28
Decals (Part 2)
30
Side Chute, Adapter
32
Grass Bag
34
Accessories - Recycling Kits
36
21" Hi-Vac Mulcherizer Kits
38
Accessory - Snapperizer
40
Accessory - Thatcherizer
42
Electric Start Group
Handles & Controls
TP 400-5143-3-WB-N
Manual No. 7006051A 21" STEEL DECK WALK BEHIND MOWER
SERIES 7
4
Handles & Controls
Footnotes:
TP 400-5143-3-WB-N
Manual No. 7006051A21" STEEL DECK WALK BEHIND MOWER
SERIES 7
5
Part No Descri
p
tionItem Qt
Note
1 7036354 1 HANDLE, Upper Used on Push
1 7036357 1 HANDLE, Upper Used on Self-Propelled
2 7036350 1 HANDLE, Middle Used on All
3 7046502 1 HANDLE, Lower Left Hand Was 38467, Used on All
4 7035342 1 HANDLE, Lower Right Hand Was 38466, Used on All
5 7017072 1 CONTROL, Blade Used on All
6 7033904 1 CLIP, Blade Control Used on All (Same either side)
7 7023820 1 CABLE, Blade Control, 47.94" Overall length B&S 3.5 H.P. Engine 1990 Model
7 7023835 1 CABLE, Blade Control, 63.87" Overall length TEC 2-cycle Engine 1990 Model
7 7023765 1 CABLE, Blade Control, 52.65" Overall length B&S 5.0 H.P. Engine 1990 Model
7 7016566 1 CABLE, Blade Control, 46.3" Overall lenght Used on Briggs (All Engines)
("91 Models & Later)
7 7016708 1 CABLE, Blade Control, 56.93" Overall length Used on Tecumseh (Side Valve
Engines) ("91 Models & Later
7 7016709 1 CABLE, Blade Control, 63.42" Overall length TEC 2 Cycle Engine 1991 &
Later
7 7016425 1 CABLE, Blade Control, 57.0" Overall length Used on Tecumseh OHV Engine
7 7017276 1 CABLE, Blade Control, 47.95" Overall length Used on Robin
8 7032826 1 HANDLE, Wheel Drive Used on Self-propelled
9 7014307 1 GRIP, Wheel Drive Handle Used on Self-propelled
10 7023134 1 CABLE, Clutch Pull (Z-BEND) Used on Self-propelled
11 7012121 1 COVER, Vinyl (Part of item 10)
12 7012122 1 SPRING, Clutch Used on Self-propelled
13 7038478 1 SECTOR, Speed Used on Self-propelled
14 7023795 1 LEVER, Speed Control Used on Self-propelled
15 7012093 1 SPRING, Speed Control Used on Self-propelled
16 7090188 1 WASHER, 3/8" Flat Used on All-different locations
17 7023801 1 GRIP, Speed Control Handle Used on Self-propelled
18 7032830 1 ANCHOR, Speed Control Used on Self-propelled
19 7032408 1 GUIDE, Lower V-Belt Used on Self-propelled
20 7023790 1 ROD, Transfer Used on Self-propelled
21 7010937 1 CLIP, Transfer Rod Used on Self-propelled
22 7090895 1 TEE-NUT, 5/16-18 Used on Self-propelled
23 7012114 1 BUSHING, Differential Used on Self-propelled
24 7090595 1 BOLT, 5/16-18 x 3/4 Flange Lock Used on Self-propelled
25 7090238 1 CAPSCREW, 5/16-24 x 1 Used on Self-propelled
26 7090799 2 BOLT, 5/16-18 x 5/8 Carriage Was 91026 (Used on All
(different locations)
27 7091601 4 NUT,5/16-18 Hex Flange Lock Was 90585 (Used on All
(different locations))
28 7090222 1 NUT, 5/16-24 Center Lock Used on Self-propelled
29 7023813 1 CLIP Cable/Wiring Used on All
Handles & Controls
TP 400-5143-3-WB-N
Manual No. 7006051A 21" STEEL DECK WALK BEHIND MOWER
SERIES 7
6
Handles & Controls
Footnotes:
TP 400-5143-3-WB-N
Manual No. 7006051A21" STEEL DECK WALK BEHIND MOWER
SERIES 7
7
Part No Descri
p
tionItem Qt
Note
30 7091013 4 SCREW, 1/4-20 x 1-7/8 Curved Head Used on All
31 7023735 4 KNOB, 5/16-18 Used on All
32 7091025 2 CAPSCREW, 1/4-28 x 1-3/8 Used on Self-propelled
33 7090053 5 LOCKWASHER, 1/4 Internal Tooth Was 91023 (Used on All
(different locations))
34 7090095 3 NUT, 1/4-20 Hex Was 91024 (Used on All
(different locations)
35 7091022 1 CAPSCREW, 1/4-28 x 1-3/4 Used on All (throttle control)
36 7014343 4 BUSHING Used on All
37 7023792 1 PIN, Clutch Handle Used on Self-propelled
38 7091020 1 PUSH-NUT (for handle pin) Used on Self-propelled
39 7023745 1 DECAL, Blade Control Used on All
40 7023901 1 GRIP, Foam 18" Used on Push
40 7022460 1 GRIP, Foam 13.5" Was 23841, Used on Self-
Propelled
41 7091077 1 BOLT, 5/16-18 x 5/8" Carriage Used on Self-Propelled
Cutting Deck, Blade, Interlock
TP 400-5143-3-WB-N
Manual No. 7006051A 21" STEEL DECK WALK BEHIND MOWER
SERIES 7
8
Cutting Deck, Blade, Interlock
Footnotes:
TP 400-5143-3-WB-N
Manual No. 7006051A21" STEEL DECK WALK BEHIND MOWER
SERIES 7
9
Part No Descri
p
tionItem Qt
Note
1 7057663 1 DECK, Mower (Includes painted deck with
decals)
2 7091601 12 NUT, 5/16-18 Hex Flange Lock Was 90585
3 7090731 9 BOLT, 5/16-18 x 1/2" Short Neck Carriage (Gr.)
4 7091303 4 BOLT, 5/16-18 x 1" Short Neck Carriage Was 90383
5 7090324 2 SCREW, 3/8-16 x 1" Self-tapping (Engine Mounting)
6 7032417 1 SPRING, Wheel Bracket Type Interlock
7 7032416 1 BRACKET, Wheel Bracket Type Interlock
8 7012048 1 INSULATOR, Interlock
9 7091122 2 SCREW, 1/4-20 x 1/2" Self-tapping Was 90539
10 7090385 1 WASHER, #8 Tab Internal Tooth Lock
11 7090379 1 SCREW, #8-18 x 3/4" Hex Head Machine
12 7090167 1 SCREW, 3/8-24 x 2" Hex Head Cap (Gr. 5)
13 7012063 1 WASHER, Cone
14 7019795 1 BLADE, Cutter
14 7017168 1 BLADE, Cutter (For Recycling Models)
15 7012927 1 HUB, Blade Drive (7/8" Dia. I.D.) (For '90 Models &. Earlier)
15 7015626 1 HUB, Blade Drive (25mm Dia. I.D.) (For '91 Models & Later)
16 7010783 2 KEY, Hi-Pro (For '90 Models & Earlier)
16 7015894 2 KEY, Woodruff (Briggs)(Tecumseh 2 Cycle) (For '91 Models & Later)
16 7016755 1 KEY, Square (Robin & Tecumseh) (For '91 Models & Later)
17 7090201 1 SCREW, 5/16-18 x 5/16" Hex Socket Set
18 7021707 1 PULLEY, Engine (Briggs 3.5 H.P.) (7/8" I.D. x 1-7/8" O.D.) (For '90 Models & Earlier)
18 7015780 1 PULLEY, Engine (Briggs) (Tecumseh 2 Cycle) (25mm I.D. x 2-
1/8" O.D.)
(For '91 Models & Later)
18 7022106 1 PULLEY, Engine (Tec. & Robin) (25mm I.D.x 2-1/8" O.D.) (For '91 Models & Later)
19 7031968 1 SHIELD, Belt Opening Cover (For Push Models Only)
20 7012135 1 BUSHING, Interlock Wire
21 7060785 1 KIT, Air Lift (Includes items 22 thru 25); For
use with P/N 1-9795 Blade
22 7032558 2 LIFT, Air
23 7090391 4 WASHER, 5/16 Internal Tooth Lock
24 7091297 4 NUT, 5/16-24 Hex Was 90223
25 7090228 4 SCREW, 5/16-24 x 11/16" Machine
26 7011791 2 RETAINER, 5/16 Bolt
27 7090799 2 BOLT, 5/16-18 x 5/8" Carriage
Front Wheel Bracket, Latches
TP 400-5143-3-WB-N
Manual No. 7006051A 21" STEEL DECK WALK BEHIND MOWER
SERIES 7
10
Front Wheel Bracket, Latches
Footnotes:
TP 400-5143-3-WB-N
Manual No. 7006051A21" STEEL DECK WALK BEHIND MOWER
SERIES 7
11
Part No Descri
p
tionItem Qt
Note
1 7051885 1 ARM ASSEMBLY, Left Wheel (Not shown) (Consists of items 2, 3, 4, 5A,6)
1 7051886 1 ARM ASSEMBLY, Right Wheel (Consists of items 2, 3, 4, 5B, 6)
2 7015761 2 BOLT, 5/16-18 Shoulder
3 7012325 2 LATCH, Height
4 7027702 2 GRIP, Latch
5 7031016 1 ARM, Left Wheel (Not shown)
5 7031017 1 ARM, Right Wheel
6 7011791 2 RETAINER, 5/16 Bolt
7 7090391 2 WASHER, 5/16 Internal Tooth Lock
8 7091511 2 NUT, 5/16-18 Hex Was 90196
9 7047971 1 BRACKET, Front Wheel
10 7021119 1 AXLE
Rear Wheels, Brackets, Latches
TP 400-5143-3-WB-N
Manual No. 7006051A 21" STEEL DECK WALK BEHIND MOWER
SERIES 7
12
Rear Wheels, Brackets, Latches
Footnotes:
TP 400-5143-3-WB-N
Manual No. 7006051A21" STEEL DECK WALK BEHIND MOWER
SERIES 7
13
Part No Descri
p
tionItem Qt
Note
1 7046983 2 BEARING Was 18767
2 7091012 6 SCREW, #10-32 x 3/8" Self-Tapping
3 7035717 2 LATCH, Height Adjusting Was 19218 (Self-Propelled
Models)
4 7090731 6 BOLT, 5/16-18 x 1/2" Short Neck Carriage
5 7091601 6 NUT, 5/16-18 Hex Flange Lock Was 90585
6 7052909 1 ASSEMBLY, Wheel Arm (Square Hole, Front Left & Rear Right) Was 51954 (Includes items
10,14,15,16,17)
7 7052908 1 ASSEMBLY, Wheel Arm (Round Hole, Front Right & Rear Left) Was 51955 (Includes Items
11,14,15,16,17)
8 7054246 1 WHEEL ARM ASSEMBLY (Rear Right "P" Models) Was 51814 Includes items
(1,2,3,12,14,15,16,17,25)
9 7054247 1 WHEEL ARM ASSEMBLY (Rear Left "P" Models) Was 51815 Includes items
(1,2,3,13,14,15,16,17,25)
10 7031016 1 ARM (Square Axle End)
11 7031017 1 ARM (Round Axle End)
12 7032722 1 ARM, Wheel Rear Right "P" Models
13 7032723 1 ARM, Wheel Rear Left "P" Models
14 7015761 2 BOLT, 5/16-18 x 1 Shoulder
15 7011791 2 RETAINER, 5/16 Bolt
16 7012325 2 LATCH, Height Adjusting (For Push Models)
17 7027702 2 GRIP, Latch
18 7036050 1 BRACKET, Right Rear Wheel (For Push Models)
19 7036049 1 BRACKET, Left Rear Wheel (For Push Models)
20 7036048 1 BRACKET, Right Rear Wheel (For Self-prop. "P" Models)
21 7036242 1 BRACKET, Left Rear Wheel (For Self-prop. "P" Models)
22 7021119 1 AXLE (For Rear on Push Models also
front on all)
23 7011780 2 RING (For Push Models)
24 7026166 1 GUARD, Rear Foot Was 37765 (Push Models)
25 7091809 2 PIN, 1/8 x 1-1/2" Cotter Was 90297
26 7019522 1 GUARD, Rear Foot (For Self-prop. "P" Models)
27 7012616 1 SUPPORT, Foot Guard
28 7091604 1 BOLT, 1/4-20 x 1/2 Short Neck Carriage Gr.5 Was 90005
29 7090053 1 WASHER, 1/4 Int. Tooth Lock Was 91023
30 7091576 1 NUT, 1/4-20 Hex Was 90063
31 7023791 1 RING
32 7090391 2 WASHER, 5/16 Int. Tooth Lock
33 7091511 2 NUT, 5/16-18 Hex Was 90196
Front Wheels
TP 400-5143-3-WB-N
Manual No. 7006051A 21" STEEL DECK WALK BEHIND MOWER
SERIES 7
14
Front Wheels
Footnotes:
TP 400-5143-3-WB-N
Manual No. 7006051A21" STEEL DECK WALK BEHIND MOWER
SERIES 7
15
Part No Descri
p
tionItem Qt
Note
1 7019195 2 WHEEL, 7 x 1.75 Plastic Rim Was 19333 on "90 Models &
Earlier
2 7019381 2 COVER, Wheel
3 7090377 2 NUT, 7/16-20 Hex Center Lock
4 7031960 2 CAP, Deep-Dish Hub
5 7031961 4 WASHER, 7/16 Flat
6 7012309 2 BUSHING, Axle
Rear Wheels
TP 400-5143-3-WB-N
Manual No. 7006051A 21" STEEL DECK WALK BEHIND MOWER
SERIES 7
16
Rear Wheels
Footnotes:
TP 400-5143-3-WB-N
Manual No. 7006051A21" STEEL DECK WALK BEHIND MOWER
SERIES 7
17
Part No Descri
p
tionItem Qt
Note
1 7019420 2 WHEEL, 9 x 2.00 Plastic Rim Was 19196 or 19334 (For Push
Models)
2 7022801 2 WHEEL, 9 x 2.00 Plastic Rim Was 19335 (For 3.5 H.P. Self-
Propelled) ('91 Models & Later)
2 7019421 2 WHEEL, 9 x 2.00 Plastic Rim Was 19197 (For 3.5 H.P. 1990
Self-Propelled Models & Earlier)
3 7022801 2 WHEEL, 9 x 2.00 Steel Rim Was 19336 (Self-Propelled)("91
Models & Later)
3 7019201 2 WHEEL, 9 x 2.00 Steel Rim Was 19198 (Self-Propelled,
1990 Models & Earlier)
4 7019385 2 COVER, Wheel (For Push & w.5 H.P. Self-
Propelled)
5 7019349 2 COVER, Wheel (For Self-Propelled)
6 7090377 2 NUT, 5/16-18 Hex Center Lock
7 7031960 4 CAP, Deep-Dish Hub
8 7031961 4 WASHER, 7/16 Flat
9 7012309 2 BUSHING, Axle (Push)
Drive System - Self Propelled
TP 400-5143-3-WB-N
Manual No. 7006051A 21" STEEL DECK WALK BEHIND MOWER
SERIES 7
18
Drive System - Self Propelled
Footnotes:
TP 400-5143-3-WB-N
Manual No. 7006051A21" STEEL DECK WALK BEHIND MOWER
SERIES 7
19
Part No Descri
p
tionItem Qt
Note
1 7012354 1 BELT, Poly-Vee
2 7034179 1 LINK, Differential Was 31880
-- 7051921 1 ASSEMBLY, Clutch Idler (Includes items 3 thru 7)
3 7032832 1 ARM, Clutch Idler
4 7012124 2 PULLEY, Idler
5 7090552 1 CAPSCREW, 1/4-28 x 1-3/8" Hex Head
6 7090303 1 NUT, 1/4-28 Hex Lock
7 7012117 2 BUSHING, 3/8 I.D. Nylon
8 7072284 1 HEX-SHAFT Was 23744
9 7019383 1 PULLEY
10 7012316 1 WASHER
11 7012126 1 SPRING, Torsion
12 7012111 1 STUD
13 7031873 1 HOLDER, Bearing (Inner Half)
14 7028014 1 BEARING, Ball Was 12304
15 7011025 1 O-RING
16 7090289 1 NUT, 3/8 Hex Center Lock
17 7031809 1 HOLDER, Bearing (Outer Half)
18 7010937 1 CLIP, 1/4 Right Arc (Transfer Rod)
19 7023790 1 ROD, Transfer
20 7012353 1 BELT, Engine Drive
-- 7053225 1 ASSEMBLY, Driven Disc Was 57444 (Includes 21 thru 28)
21 7038486 1 PLATE, Thrust
22 7010746 1 RING, Retaining
23 7026693 1 BEARING, Ball Was 15474
24 7090981 4 SCREW, #10-32 x 1/4" Self-Tapping Machine
25 7061276 1 ASSEMBLY, Hub Was 51616 (Includes 11108
Bushing & 90913 Screws)
26 7023364 1 DRIVEN-RING
27 7031013 1 PLATE, Ring Retaining
28 7090913 5 SCREW, #10-24 x 1/2" Hex Washer Self-Tap (Torx)
29 7012125 1 GUIDE, Thrust Plate
30 7090390 2 WASHER, 3/8 Internal Tooth Lock
31 7090122 3 WASHER, 3/8" Flat
32 7091630 3 NUT, 3/8-24 Hex Was 90155
33 7091511 1 NUT, 5/16-18 Hex Was 90196
34 7090187 1 WASHER, 5/16 Split Lock
35 7090316 1 BOLT, 5/16-18 x 3/4 Carriage
Drive System - Self Propelled
TP 400-5143-3-WB-N
Manual No. 7006051A 21" STEEL DECK WALK BEHIND MOWER
SERIES 7
20
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
Leht laadib ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46

Snapper OP21507B Kasutusjuhend

Snapper
Bränd
Snapper
Mudel
OP21507B
Kategooria
Muruniidukid
Tüüp
Kasutusjuhend
Laadige alla PDF
aruanne

Seotud paberid

Muud dokumendid