Makita DTR181 Kasutusjuhend

Bränd: Makita

Mudel: DTR181

Kategooria: Elektrilised tööriistad

Tüüp: Kasutusjuhend

DTR181

EN Cordless Rebar Tying Tool INSTRUCTION MANUAL 12

SV Trådlöst bindverktyg för

armeringsjärn BRUKSANVISNING 23

NO Batteridrevet verktøy til

binding av armeringsjern BRUKSANVISNING 34

FI Akkukäyttöinen raudoituksen

sidontakone KÄYTTÖOHJE 45

DA Akku maskine til binding af

armeringsjern BRUGSANVISNING 55

LV Bezvada stiegru apsiešanas

darbarīks LIETOŠANAS INSTRUKCIJA 66

LT Belaidis armatūros strypų

rišimo įrankis NAUDOJIMO INSTRUKCIJA 77

ET Juhtmevaba sarrusevarraste

sidumistööriist KASUTUSJUHEND 88

RU Аккумуляторный

Вязальщик Арматуры РУКОВОДСТВО ПО

ЭКСПЛУАТАЦИИ 99

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

Fig.16

Fig.17

Fig.18

Fig.19

Fig.20

Fig.21

Fig.22

Fig.23

Fig.24

Fig.25

Fig.26

Fig.27

Fig.28

Fig.29

Fig.30

Fig.31

Fig.32

Fig.33

Fig.34

45°

Fig.35

Fig.36

Fig.37

Fig.38

45°

Fig.39

Fig.40

Fig.41

Fig.42

Fig.43

Fig.44

Fig.45

Fig.46

Fig.47

Fig.48

Fig.49

Fig.50

Fig.51

Fig.52

Fig.53

Fig.54

Fig.55

Fig.56

Fig.57

Fig.58

Fig.59

Fig.60

Fig.61

Fig.62

Fig.63

Fig.64

Fig.65

12 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: DTR181

Tie wire (Optional accessory) Annealing iron tie wire ø0.8 mm

Poly coated tie wire ø0.9 mm

Galvanized tie wire *1 ø0.8 mm

Approximate number of ties

per reel

Annealing iron tie wire Approximately 75 ties

Poly coated tie wire Approximately 65 ties

Galvanized tie wire *1 Approximately 75 ties

Overall length 317 mm

Rated voltage D.C. 18 V

Net weight 2.4 - 2.7 kg

*1 Available only when an optional wire guide B complete (EG) is installed in the arm.

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsandbatterycartridgemaydierfromcountrytocountry.

• Theweightmaydierdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

est combinations, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B

Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /

DC18SH / DC18WC

• Some of the battery cartridges and chargers listed above may not be available depending on your region of

residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

andchargersmaycauseinjuryand/orre.

Combination of rebars that can be tied

Combination of 2 rebars

#4 (13 mm) #5 (16 mm) #6 (19 mm) #7 (22 mm)

#4 (13 mm)

---

#5 (16 mm)

- -

#6 (19 mm) -

#7 (22 mm)

#8 (25 mm)

#9 (29 mm) -

#10 (32 mm) - -

#11 (35 mm) ---

* The combination is not designed for high tying strength.

13 ENGLISH

Combination of 3 rebars

#3 x #3

(10 mm x 10 mm)

#4 x #4

(13 mm x 13 mm)

#5 x #5

(16 mm x 16 mm)

#3 (10 mm)

#4 (13 mm)

#5 (16 mm)

#6 (19 mm)

#7 (22 mm)

#8 (25 mm)

* The combination is not designed for high tying strength.

Combination of 4 rebars

#3 x #3 (10 mm x 10 mm) #4 x #4 (13 mm x 13 mm)

#3 x #3 (10 mm x 10 mm)

#4 x #4 (13 mm x 13 mm)

#5 x #5 (16 mm x 16 mm)

NOTICE: If there is a gap between rebars or if the tool is used at an incorrect orientation, the rebars may not be

able to be tied.

Symbols

The followings show the symbols which may be used

for the equipment. Be sure that you understand their

meaning before use.

Read instruction manual.

Wear safety glasses.

Do not expose to rain.

Keep hands away from the wire reel or wire

when operating the tool.

Keep hands away from the tool tip.

Push the release lever before loading

the tie wire. Having installed the tie wire,

release the lock lever.

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical

and electronic equipment, accumulators

and batteries may have a negative impact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household waste!

In accordance with the European Directive on

waste electrical and electronic equipment and on

accumulators and batteries and waste accumu-

lators and batteries, as well as their adaptation to

national law, waste electrical equipment, batteries

and accumulators should be stored separately

and delivered to a separate collection point for

municipal waste, operating in accordance with the

regulations on environmental protection.

This is indicated by the symbol of the

crossed-out wheeled bin placed on the

equipment.

Intended use

The tool is intended for tying rebars.

Noise

The typical A-weighted noise level determined accord-

ing to EN60745-2-18:

Sound pressure level (LpA) : 82 dB (A)

Sound power level (LWA) : 90 dB (A)

Uncertainty (K) : 3 dB (A)

NOTE: The declared noise emission value(s) has

been measured in accordance with a standard test

method and may be used for comparing one tool with

another.

NOTE: The declared noise emission value(s)

may also be used in a preliminary assessment of

exposure.

14 ENGLISH

WARNING: Wear ear protection.

WARNING:

The noise emission during actual

use of the power tool can dier from the declared

value(s) depending on the ways in which the tool is

used especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (tak-

ing account of all parts of the operating cycle such

as the times when the tool is switched o and when

it is running idle in addition to the trigger time).

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN60745-2-18:

Work mode: Tying metal rod

Vibration emission (ah) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

NOTE: The declared vibration total value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also

be used in a preliminary assessment of exposure.

WARNING: The vibration emission during

actual use of the power tool can dier from the

declared value(s) depending on the ways in which

the tool is used especially what kind of workpiece

is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

o and when it is running idle in addition to the

trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listedbelowmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Cordless rebar tying tool safety

warnings

Never point the tool toward a person. Never put

your hands or feet close to the tool tip. If you

accidentally operate the tool while it is touching

someone, it will lead to an unexpected accident.

2. Do not load wire while the power to the tool is

turned on. Otherwise, you may get caught in the

wireandinjured.

3. Do not use the tool without closing the reel

cover.Otherwise,thewirereelmaycomeoand

cause an accident.

4. Be sure to check that the diameters of rebars

to be tied are within the tool capacity before

beginning work.

5. Wear clothes that have close-tting hemlines

and sleeves. Do not work with a towel or other

object wrapped around your neck. Otherwise,

they may get caught in the rotating part and cause

an accident.

6. Be sure to inspect the following points before

using the tool.

• Check that no parts are damaged

• Check that no bolts are loose

• Check that safety devices operate

normally

7. If any abnormalities are found, stop using the

tool immediately. Do not repair the tool by

yourself. Ask your local Makita Service Center

for repairs. If the tool is used in an incomplete

state, an accident may occur.

8. When installing the battery cartridge, be sure

to lock the trigger and do not place your nger

on the trigger. Incorrect operation may cause an

accident.

When tying rebars, exercise care not to move

them.Ifrebarsmoveduetotying,youmaybeinjured.

10. Do not touch the wires during the wire tying

process. Otherwise, you may get caught in the

wireandinjured.

11. Do not bring your hands close to the tying

point during the wire tying process. Otherwise,

youmaygetcaughtinthewireandinjured.

12. Hold the grip of the tool rmly during the wire

tying process. Otherwise, your wrist may be

twisted or your body may be pulled, which may

resultinaninjury.

13. Do not move to the next tying point until the

current wire tying process is completed.

Otherwise,youmaybeinjured.

14.

Pay attention to the end of the wire during the wire

tying process. Otherwise, your hand may be caught

bytheendofthewire,andyoumaybeinjured.

15. Do not touch the contact plate during the wire

tying process. If you need to touch the contact

plate, be sure to lock the trigger, or turn the

power switch o and remove the battery car-

tridge.Otherwise,youmaybeinjured.

16. When you have completed the wire tying pro-

cess, pull the tool up vertically. Otherwise, the

arm may be caught on rebars, which may cause

an accident.

15 ENGLISH

17.

Be careful not to drop, bump, or hit the tool. If a

strong impact is applied prior to the tool being

used, make sure that the tool is not damaged

or cracked, and that the safety devices operate

normally. Otherwise, an accident may occur.

18.

If any of the following phenomena occur, lock

the trigger, turn the power switch o, and

remove the battery cartridge from the tool. If the

tool operates incorrectly, an accident may occur.

• If an operating sound is heard as soon as

the battery cartridge is mounted.

• If overheating or abnormal smells or

noises are detected.

• When you are taking measures in

response to the error display. (Ask your

local Makita Service Center for repairs.)

• When loading or unloading a wire reel.

• When you move while holding the tool

during work.

• When you do not use the tool.

• When you inspect or adjust the tool.

• When you remove a stranded wire.

19. When working on scaolding, always stabilize

it and work using a posture that will ensure

you maintain your balance.Ifscaoldingis

unstable, an accident may occur.

20. When working on a roof or similar locations,

move in a forward direction while working so

that you can see where you are going. If you

move in a backward direction while working, you

may lose your footing and cause an accident.

21.

If you are working in a highly elevated location,

ensure that no one is below you, and pay atten-

tion to ensure you do not drop any tools while

working. Dropping the tool may cause an accident.

22. Do not use the tool for any work other than

wire tying. Otherwise, an accident may occur.

23. Always use Makita's genuine wires. If wires are

not used for a long period of time, they may

rust. Do not use rusted wires. Otherwise, they

may cause an accident.

24. After tying, check for wire breakage due to

excessive twisting. If any wires are broken,

tying strength will be lost. Adjust the tying

strength, and tie the rebars again.

25. Securely place the arm against the rebars. If

it is not securely positioned, a clearance will be

created between the rebars, and tying strength will

be compromised.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper with the battery

cartridge.Itmayresultinare,excessiveheat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current ow,

overheating, possible burns and even a breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re,excessiveheat,orexplosion.

9. Do not use a damaged battery.

10.

The contained lithium-ion batteries are subject to

the Dangerous Goods Legislation requirements.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consulting an

expert for hazardous material is required. Please also

observe possibly more detailed national regulations.

Tapeormaskoopencontactsandpackupthe

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15.

Do not touch the terminal of the tool immediately

after use as it may get hot enough to cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge.Itmaycauseheating,catchingre,

burst and malfunction of the tool or battery car-

tridge,resultinginburnsorpersonalinjury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near high-voltage electri-

cal power lines. It may result in a malfunction or

breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

16 ENGLISH

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causingres,personalinjuryanddamage.Itwill

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch o the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridgermlymaycausethemtoslipoyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator as

showninthegure,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►Fig.2: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydierslightly

from the actual capacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

the battery protection system works.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem.Thissystemautomaticallycutsopowertothe

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the tool or battery is operated in a manner that

causes it to draw an abnormally high current, the tool

automatically stops and the corresponding error number

is displayed on the display panel. In this situation, turn

thetooloandstoptheapplicationthatcausedthetool

to become overloaded. Then turn the tool on to restart.

Overheat protection

When the tool or battery is overheated, the tool stops

automatically and the corresponding error number is

displayed on the display panel. In this case, let the tool

and battery cool before turning the tool on again.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically and the corresponding error number is

displayed on the display panel. In this case, remove the

battery from the tool and charge the battery.

17 ENGLISH

Main power switch

CAUTION:

When you turn the power on, never

bring your limbs or face close to the binding or rotat-

ing parts of the tool tip.Otherwise,youmaybeinjured.

CAUTION: When the power is turned on,

never touch the binding or rotating parts of the

tool tip.Otherwise,youmaybeinjured.

CAUTION:

Before inserting the battery cartridge,

be sure to release your ngers from the switch trigger

and lock the trigger. If you insert the battery cartridge

while the switch trigger is being pulled, it may cause an

accident if the wire tying process is accidentally carried out.

►Fig.3

When you press the power button, the power turns

on and the tying mode lamp lights up. In order for the

tooltoadjustitsinitialposition,itoperatestemporarily.

Whenadjustmenthascompleted,thetoolstopsauto-

matically. When you press the power button again, the

powerturnsoandthetyingmodelampgoesout.

►Fig.4: 1. Tying mode lamp 2. Power button

NOTE:

Thetoolhasanautopower-ofunction.Ifthe

switch trigger is not pulled for 10 minutes, the tool is auto-

maticallyturnedotoreducebatterypowerconsumption.

NOTE: To restart the tool, turn the power on again.

Mode switching button

When the power is turned on and the tying mode lamp

is lit, you can select the single actuation mode or the

continuous actuation mode via the mode switching but-

ton. When you turn the power on again, the tool starts in

the mode that was most recently selected.

►Fig.5: 1. Mode switching button 2. Single actuation

mode 3. Continuous actuation mode

Switch action

WARNING: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

CAUTION: When not operating the tool,

depress the trigger-lock button from side to

lock the switch trigger in the OFF position.

►Fig.6: 1. Switch trigger 2. Trigger-lock button

To prevent the switch trigger from accidentally pulled,

the trigger-lock button is provided. To start the tool,

depress the trigger-lock button from A side and pull the

switch trigger. Release the switch trigger to stop. After

use, press in the trigger-lock button from B side.

When you pull the switch trigger, the tool performs the

next sequential operations as follows, and the tool stops

automatically.

1. Feed the wire.

2. Cut the wire.

3. The hook holds and twists the wire.

4. The hook returns to the original position.

Tying strength setting

CAUTION: Be sure to lock the trigger before

starting the adjustment. When you turn the power

on, never bring your limbs or face close to the

binding or rotating parts of the tool tip. Otherwise,

youmaybeinjured.

►Fig.7

Youcansetthetyingstrengthbyadjustingthetying

strengthadjustingbutton.Tyingstrengthisshownon

the display panel.

►Fig.8: 1.Tyingstrengthadjustingbutton2. Display

panel

Ifthewireisbrokeno,tyingstrengthwillbelost.After

tying, check the twisted portion for breakage.

Ifthewireisbrokeno,adjustthetyingstrengthusing

thetyingstrengthadjustingbutton,andtietherebars

again.

Remaining battery notication

When the battery voltage drops below the required

level, the tool will stop operating, an error tone will

sound, and the number "4" will appear on the display

panel. The error tone will continue to sound until the

poweristurnedo.

NOTE: If the ambient temperature is extremely low,

the error tone may sound even when the battery

containssucientpower.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before carrying out any work on the tool.

Loading the tie wire (wire reel)

CAUTION: Before mounting or dismounting

tie wires and accessories, be sure to turn the

power o, lock the trigger, and remove the battery

cartridge. Failure to do so may cause an accident.

NOTICE: Using wires other than Makita's genu-

ine tie wires may cause the tool to malfunction.

1. Push the release lever, and lock it with the lock

lever.

►Fig.9: 1. Release lever 2. Lock lever

When you push the release lever, a gap is created

between the left and right feed gears.

►Fig.10: 1. Release lever 2. Lock lever 3. Feed gears

2. Open the reel cover.

►Fig.11: 1. Reel cover

3. Mount the wire reel on the tool in the orientation

showninthegure.

►Fig.12: 1. Wire reel

18 ENGLISH

NOTICE: Be sure to mount the wire reel in the

orientation shown in the gure. If it is mounted the

other way around, the wire will be released and may

be twisted.

4. Unhook the wire tip from the hook of reel.

►Fig.13: 1. Hook

5. Make the tip of the wire straight, and pass the wire

through the guide.

►Fig.14: 1. Guide

NOTE: If the tip of the wire is bent when it is passed

throughtheguide,thewiremaybecomejammedin

the tool.

NOTE: If you force the wire when trying to pass it

throughtheguide,thewiremaybecomejammed.

6. Pull the wire out approximately 10 mm from the tip

of the arm.

►Fig.15: 1. Arm 2. Approximately 10 mm

NOTICE: If the length of the pulled-out wire is

insucient, the wire may be broken o when tied,

or tying strength may be compromised due to

insucient wraps.

7. Rewind the wire to eliminate its slack.

►Fig.16

8. Release the lock lever. The release lever returns,

and the wire is held by the left and right gears.

►Fig.17: 1. Lock lever 2. Release lever

►Fig.18: 1. Gear 2. Path of the wire 3. Wire

NOTICE: When the lock lever is released and

when the left and right gears mesh with each

other, the grooves in the gears form a space. This

space becomes the path for the wire. Make sure

that the wire is passed through this path.

9. Close the reel cover.

►Fig.19: 1. Reel cover

Replacing wire guide B

Optional accessory

The wire guide B (in silver color) in the arm can be

replaced with an optional wire guide B (EG) (in black

color) according to the type of tying wire to use.

Find the right combination in the following table. Then

replace the standard equipped wire guide B with an

optional wire guide B (EG) if necessary.

Standard

equipped wire

guide B complete

(silver)

Optional wire

guide B complete

(black)

Annealing iron tie wire

Poly coated tie wire -

Galvanized tie wire -

— : The combination is not valid.

1. Loosen bolts A and B using the hex wrench

included in the tool package.

►Fig.20: 1. Hex wrench

►Fig.21: 1. Bolt A 2. Bolt B 3. Contact plate cover

4. Standard equipped wire guide B (silver)

NOTICE: Do not forcibly remove any bolts that

cannot be removed using the hex wrench.

2. Pull the contact plate cover up in the direction of

the arrow and remove it. Bolt B will be removed at the

same time.

►Fig.22: 1. Contact plate cover 2. Bolt B

3. Remove bolt A, and remove the standard

equipped wire guide B (silver).

►Fig.23: 1. Bolt A 2. Standard equipped wire guide

B (silver)

4. Replace the standard equipped wire guide B (in

silver color) with an optional wire guide B (EG) (in black

color).

►Fig.24: 1. Optional wire guide B (EG) (in black

color).

5. Align the pipe of the tool with the groove inside the

optional wire guide B (EG) (black), and assemble them.

►Fig.25: 1. Pipe 2. Groove 3. Optional wire guide B

(EG) (black).

6. Fix the optional wire guide B (EG) (black) by tem-

porarily tightening bolt A.

►Fig.26: 1. Bolt A 2. Optional wire guide B (EG)

(black).

7. Install the contact plate cover in the direction of

the arrow.

►Fig.27: 1. Contact plate cover

8. Fix the optional wire guide B (EG) (black) and con-

tact plate cover securely by tightening bolt A and bolt B.

►Fig.28: 1. Optional wire guide B (EG) (black).

2. Contact plate cover 3. Bolt A 4. Bolt B

9. Afterassembling,conrmthatthecontactplate

canmoveasshowninthegure.

►Fig.29: 1. Contact plate

NOTE: If the contact plate is caught, press it as

showninthegure.

►Fig.30

OPERATION

Checking before work

CAUTION: If the tool has a safety mecha-

nism-related problem, do not use it. If you continue

to use it, an accident may occur.

Before using the tool, make sure that the safety mecha-

nism operates normally. If the tool operates without the

safety mechanism operating, stop using the tool imme-

diately. Ask your local Makita Service Center for repairs.

19 ENGLISH

Checking the trigger-lock

The tool has the trigger-lock to prevent the tool from

operating when you do not intend to use it. Lock the trig-

gerandconrmthattheswitchtriggercannotbepulled.

Checking the curl guide

To prevent the operator from touching the binding or

rotating parts of the tool tip by mistake, the tool will not

operate even if the switch trigger is pulled while the

curl guide is opened. When the operator releases their

ngerfromtheswitchtriggerandclosesthecurlguide,

the tool can operate.

►Fig.31: 1. Curl guide

Checkout for curl guide open/close

detection

Remove the tie wire, check the tool operation according

to the following steps, and make sure that the tool does

not start if the curl guide is open.

1. Turnthepowero,andleavethecurlguideopen.

2. Turn the power on.

If the tool will not operate and if the value "2" is shown

on the display panel, the state of the tool is normal. Turn

thepowero,andclosethecurlguide.

If the tool operates and if no error is shown on the dis-

play panel, the state of the tool is abnormal. Stop using

the tool immediately, and ask your local Makita Service

Center for repairs.

CAUTION: If you open the curl guide and turn

the power on to check the interlock, hold the curl

guide as shown in the gure. Never bring your

limbs or face close to the binding or rotating parts

of the tool tip.Otherwise,youmaybeinjured.

►Fig.32

Tying work

CAUTION: Before inserting the battery car-

tridge, be sure to release your ngers from the

switch trigger and lock the trigger. If you insert

the battery cartridge while the switch trigger is being

pulled, it may cause an accident if the wire tying

process is accidentally carried out.

CAUTION: When you turn the power on, never

bring your limbs or face close to the binding or

rotating parts of the tool tip. Otherwise, you may

beinjured.

CAUTION: When the power is turned on,

never touch the binding or rotating parts of the

tool tip.Otherwise,youmaybeinjured.

►Fig.33

Preparation before work

1. Make sure that the battery cartridge is removed

and the trigger is locked.

2. Insert the battery cartridge into the tool, and turn

the power on. When you turn the power on, the wire is

cut automatically.

NOTICE: Make sure that the tying mode lamp

lights up when the power is turned on. If it does

not light up, recharge the battery.

3. Release the trigger lock.

►Fig.34: 1. Trigger-lock button 2. Switch trigger

3. Power button 4. Tying mode lamp

Single actuation mode

1. Pushthearmrmlyagainstthetyingpoint.Make

sure to place the tool vertically over the rebars and

press the arm on the tying point at a 45° angle against

the crossed rebars.

►Fig.35: 1. Arm

2. Pull the switch trigger once.

3. The wire is fed and cut automatically.

4. The hook holds and twists the wire, then returns to

the original position after the wires have been tied.

5. After tying, be careful not to hook the arm on the

rebars, and then pull the tool up.

►Fig.36

CAUTION: If the wire has clung to the binding

part of the tool tip, turn the power of the tool o.

Lock the trigger, remove the battery cartridge,

and remove the wire using tools such as nippers

or pliers.

►Fig.37

Continuous actuation mode

1. Switch the tool mode from the single actuation

mode to the continuous actuation mode using the mode

switching button.

►Fig.38: 1. Mode switching button

2. Release the trigger lock.

3. While pulling the switch trigger, push the tool

vertically against the rebars, and press the arm against

the point where the rebars cross at a 45-degree angle.

Pressthecontactplatermlyagainstthetyingpoint.

The wire will be tied.

►Fig.39: 1. Contact plate

4. After tying, be careful not to hook the arm on the

rebars, and then pull the tool up.

►Fig.40

Cautions on working

• If you move the arm from the tying position during

the wire tying process, the wire will get stuck on

the hook, which may lead to incorrect tying.

• Keep pressing the tool against the rebars until the

wire tying process is completed.

• Do not move to the next tying point until the cur-

rent wire tying process is completed.

• The tool tip rotating part (hook) twists the wire

duringthewiretyingprocess.Holdthegriprmly

so that your body is not pulled by the tool.

• Do not touch the wires during the wire tying

process.

20 ENGLISH

• If you are repeating the wire tying processes in

thesingleactuationmode,fullyreleaseyournger

from the switch trigger. Then, continue to operate

the switch trigger.

• If you pull the switch trigger when there is no tie

wire left, an error is displayed. Replace with a new

tie wire and restart the tool.

Tying tips

• Tilt the tool at a 45° angle against the crossed

rebars, and tie the wire in alternate orientations as

showninthegure.

►Fig.41

• Tiethewireontotheat(withnounevenness)

sections of crossed rebars.

►Fig.42

• Iftyingstrengthisinsucient,changethetying

orientation and perform tying twice so that tying

strength increases.

►Fig.43

NOTICE: When you make the second tie, bend

the tail of the rst tie before making the second

tie. Otherwise, the wire may be repelled a second

time. It may cling to the tool tip, and the hook may be

damaged.

Replacing the tie wires

CAUTION: When you replace the wire, be sure

to turn the power o, lock the trigger, and remove

the battery cartridge. Failure to do so may cause an

accident.

1. When wire has been used up, an error tone will

sound and error "1" will be displayed.

2. Lockthetrigger,turnthepowero,andremove

the battery cartridge.

3. Push the release lever, and lock it with the lock

lever.

►Fig.44: 1. Release lever 2. Lock lever

4. Remove the wire reel from the tool.

NOTE: When wire has been used up normally,

approximately 20 cm of the wire remains wound on

the reel. In this state, replace the wire reel with a new

one.

Ifitisdiculttoremovethewirereelfromthetool,

follow the steps below.

1. Insert the battery cartridge into the tool, and

turn the power on. The tool feeds the wire and cuts it

automatically.

2. Lockthetrigger,turnthepowero,andremove

the battery cartridge.

3. Remove the wire breaks using tools such as nip-

pers or pliers.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Cleaning the cutter section

When the tool is used, dust and wire particles may

become adhered to the cutter section. In such a case,

clean the cutter section according to the following pro-

cedure. The cleaning should be done each time you use

up a box of reel. (50 pcs.)

Using the wire brush

1. Open the reel cover.

►Fig.45: 1. Reel cover

2. Push the release lever, and lock it with the lock

lever.

►Fig.46: 1. Release lever 2. Lock lever

3. Pass the wire brush through the guide.

When inserting the wire brush, hold it short and push it

into the guide little by little.

►Fig.47: 1. Wire brush

►Fig.48: 1. Gear 2. Guide 3. Wire brush

4. Push in the wire brush until its top end comes out

from the tip of the arm. And then pull out the wire brush.

This action is enough with one time.

►Fig.49: 1. Arm 2. Wire brush

5. Close the reel cover.

►Fig.50: 1. Reel cover

Using the air duster gun

Open the reel cover, push the release lever, and lock it

with the lock lever. Then bring the air duster gun close

to the guide and blow the air. Make sure the air comes

from the tip of the arm.

►Fig.51: 1. Air duster gun 2. Guide

Cleaning with disassembly

If the cutter section is clogged or a wire is caught in it,

disassemble the parts and clean them.

Leht laadib ...

Makita DTR181 Kasutusjuhend

Bränd: Makita

Mudel: DTR181

Kategooria: Elektrilised tööriistad

Tüüp: Kasutusjuhend

Laadige alla PDF

aruanne

teistes keeltes

svenska: Makita DTR181 Användarmanual
dansk: Makita DTR181 Brugermanual

Makita DTR181 Kasutusjuhend

Makita DTR181 Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid