Sonicare HX6921/06 Kasutusjuhend

FlexCare+

900+ series

Rechargeable

sonic toothbrush

1

FlexCare+ 900+ series

ENGLISH 6

БЪЛГАРСКИ 20

ČEŠTINA 37

EESTI 51

HRVATSKI 65

MAGYAR 79

ҚАЗАҚША 94

LIETUVIŠKAI 114

LATVIEŠU 126

POLSKI 140

ROMÂNĂ 156

РУССКИЙ 171

SLOVENSKY 189

SLOVENŠČINA 204

SRPSKI 218

УКРАЇНСЬКА 233

6

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet

from the support that Philips offers, register your product at

www.philips.com/welcome.

Important

Read this user manual carefully before you use the

appliance and save it for future reference.

Danger

- Keep the charger and/or sanitiser away from water.

Do not place or store it over or near water

contained in a bathtub, washbasin, sink etc. Do not

immerse the charger and/or sanitiser in water or

any other liquid. After cleaning, make sure the

charger and/or sanitiser is completely dry before

you connect it to the mains.

Warning

- The mains cord cannot be replaced. If the mains

cord is damaged, discard the charger and/or

sanitiser.

- Always have the charger and/or sanitiser replaced

with one of the original type in order to avoid a

hazard.

- Do not use the charger and/or sanitiser outdoors

or near heated surfaces.

- If the appliance is damaged in any way (brush

head, toothbrush handle, charger and/or sanitiser),

stop using it. This appliance contains no user-

serviceable parts. If the appliance is damaged,

ENGLISH

contact the Consumer Care Centre in your

country (see chapter ‘Guarantee and support’).

- This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given

supervision or instruction concerning use of the

appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by

children unless they are older than 8 and supervised.

- Discontinue use of the sanitiser if the UV light bulb

remains on when the door is open. UV light can be

harmful to the human eye and skin. Keep the

sanitiser out of the reach of children at all times.

Caution

- Do not clean the brush head, the handle, the

charger, the charger cover and/or the sanitiser in

the dishwasher.

- If you have had oral or gum surgery in the

previous 2 months, consult your dentist before

you use the toothbrush.

- Consult your dentist if excessive bleeding occurs

after using this toothbrush or if bleeding continues

to occur after 1 week of use.

- The Sonicare toothbrush complies with the safety

standards for electromagnetic devices. If you have

ENGLISH 7

a pacemaker or other implanted device, contact

your physician or the manufacturer of the implanted

device prior to use.

- If you have medical concerns, consult your doctor

before you use the Sonicare.

- This appliance has only been designed for cleaning

teeth, gums and tongue. Do not use it for any other

purpose. Stop using the appliance and contact your

doctor if you experience any discomfort or pain.

- Do not use other brush heads than the ones

recommended by the manufacturer.

- If your toothpaste contains peroxide, baking soda

or bicarbonate (common in whitening toothpastes),

thoroughly clean the brush head with soap and

water after each use. This prevents possible cracking

of the plastic.

- The UV light bulb is hot during and immediately

after the sanitising cycle. Do not touch the UV

light bulb when it is hot.

- Do not operate the sanitiser without the protective

screen in place to avoid contact with a hot bulb.

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable standards and

regulations regarding exposure to electromagnetic elds.

General description (Fig. 1)

1 Hygienic travel cap

2 Brush head

ENGLISH8

3 Interchangeable colour code ring

4 Handle with soft grip

5 Power on/off button

6 Mode button

7 Brushing modes

8 Deluxe recharge gauge

9 UV sanitiser base with integrated charger and cord wrap

(specic types only)

10 UV sanitiser (specic types only)

11 Deluxe charger (specic types only)

12 Charger cover with brush head holder

13 Travel charger

14 Charger base with cord wrap

- Not shown: UV light bulb

- Not shown: Sanitiser drip tray

- Not shown: Protective screen for UV light bulb

Preparing for use

Changing the colour code ring

Sonicare brush heads come with interchangeable colour code rings to

identify your brush head.

To change the colour code ring:

1 Pull the colour code ring from the bottom of the brush head (Fig. 2).

2 Install a new ring by slipping one edge of the new ring over the

bottom of the brush head (Fig. 3).

Attaching the brush head

1

Align the brush head so the bristles face the front of the handle. (Fig. 4)

2 Firmly press the brush head down on the metal shaft until it stops.

ENGLISH 9

Note: There is a small gap between the colour code ring and the handle.

Charging your Sonicare

1 Put the mains plug of the charger or sanitiser in the wall socket.

2 Place the handle on the charger or sanitiser (Fig. 5).

, The ashing light of the battery gauge indicates that the toothbrush

is charging.

- 1 solid green LED indicates that the toothbrush is 34-66% charged.

- 2 solid green LEDs indicate that the toothbrush is 67-94% charged.

- 3 solid green LEDs indicate that the toothbrush is fully charged.

Note: If the battery charge of your Sonicare is low, you hear 3 beeps and

1 LED of the recharge gauge ashes yellow for 30 seconds after completing

the brushing cycle.

Note: To keep the battery fully charged at all times, you may keep your Sonicare

on the charger when not in use. Once the Sonicare is fully charged, the charger

draws minimal energy from the wall socket.

Note: It takes at least 24 hours to fully charge the battery.

Using the Sonicare

Brushing instructions

1 Wet the bristles and apply a small amount of toothpaste.

2 Place the toothbrush bristles against the teeth at a slight angle

towards the gumline (Fig. 6).

3 Press the power on/off button to switch on the Sonicare.

4 Apply light pressure to maximise Sonicare’s effectiveness and let

the Sonicare toothbrush do the brushing for you. Do not scrub.

5 Gently move the brush head slowly across the teeth in a small back

and forth motion so the longer bristles reach between your teeth.

Continue this motion throughout your brushing cycle.

Note: To make sure you brush evenly throughout the mouth, divide your

mouth into 4 sections using the Quadpacer feature (see chapter ‘Features’).

ENGLISH10

6 Begin brushing in section 1 (outside top teeth) and brush for

30 seconds before moving to section 2 (inside top teeth). Continue

brushing in section 3 (outside bottom teeth) and brush for 30 seconds

before moving to section 4 (inside bottom teeth) (Fig. 7).

7 After you have completed the brushing cycle, you can spend additional

time brushing the chewing surfaces of your teeth and areas where

staining occurs. You may also brush your tongue, with the toothbrush

switched on or off, as you prefer (Fig. 8).

Your Sonicare is safe to use on:

- Braces (brush heads wear out sooner when used on braces)

- Dental restorations (llings, crowns, veneers)

Brushing modes

Sonicare automatically starts in the default Clean mode.

1 Prior to switching on the Sonicare, press the mode button to

toggle between modes.

, The selected brushing mode illuminates.

, Once a brushing mode has been selected, it remains active until

another brushing mode is selected.

Note: When the toothbrush is switched on, you cannot toggle between modes.

The following brushing modes are available:

Clean

Complete whole mouth cleaning (2 minutes).

Gum Care

Complete whole mouth cleaning (2 minutes) plus gentle cleaning for

problem areas and along the gumline (1 minute).

Refresh

Touch-up for a quick clean (1 minute).

Sensitive

Gentle cleaning for sensitive gums and teeth (2 minutes).

Massage

Gentle gum stimulation (2 minutes).

ENGLISH 11

Note: When Sonicare is used in clinical studies, the default 2-minute Clean

mode must be selected. The handle has to be fully charged. Deactivate the

Easy-start feature. For areas where excess staining occurs, an additional

30 seconds of brushing time can be spent to help remove stains.

Features

Easy-start

This Sonicare type comes with the Easy-start feature activated.

The Easy-start feature gently increases power over the rst 14 brushings

to help you get used to brushing with the Sonicare.

Note: Each of the rst 14 brushings must be at least 1 minute in length to

properly move through the Easy-start ramp-up cycle.

Deactivating or activating the Easy-start feature

1 Attach your brush head to the handle.

2 Place the handle on the plugged-in charger.

- To deactivate Easy-start:

Press and hold the power on/off button for 2 seconds. You hear 1 beep

to indicate that the Easy-start feature has been deactivated.

- To activate Easy-start:

Press and hold the power on/off button for 2 seconds. You hear 2 beeps

to indicate that the Easy-start feature has been activated.

Note: Using the Easy-start feature beyond the initial ramp-up period is not

recommended and reduces Sonicare’s effectiveness in removing plaque.

Smartimer

The Smartimer indicates that your brushing cycle is complete when it

automatically switches off the toothbrush at the end of the brushing cycle.

Dentists recommend brushing at least 2 minutes twice a day.

Quadpacer

- The Quadpacer is an interval timer that has a short beep and pause

to remind you to brush the 4 sections of your mouth. Depending on

the brushing mode you have selected, the Quadpacer beeps at different

ENGLISH12

intervals during the brushing cycle. See section ‘Brushing modes’

in chapter ‘Using the Sonicare’ (Fig. 7).

The Quadpacer feature on this type has been activated. To deactivate or

reactivate the Quadpacer feature:

1 Place the handle with a brush head attached on the plugged-in charger.

2 Press and hold the mode button for 2 seconds.

, You hear 1 beep to indicate the Quadpacer has been deactivated

or you hear 2 beeps to indicate the Quadpacer has been activated.

Cord wrap on deluxe charger (specic types only)

If your type includes the deluxe charger cover and base, the travel charger

is pre-installed inside the cover. If you want to shorten the mains cord,

you can store excess cord in the cord wrap feature built into the charger

base.

1 To separate the charger cover from the charger base, press the two

grey snap bars on the charger base and pull the white charger cover

upwards. (Fig. 9)

2 Wrap excess power cord around the grey charger base as shown

in the picture. Be sure to wrap the cord on the inside of the two

snap levers. (Fig. 10)

3 When you have stored the excess cord, guide the mains cord

through the small groove in the rear of the grey charger base. (Fig. 11)

4 To reattach the charger cover, press it down over the charger base

until it snaps into place.

Tip: For extra convenience during travel, you can remove the travel charger

and use it without the charger cover and charger base.

Cord wrap on sanitiser with integrated charger

(specic types only)

- If your type includes the sanitiser, you can store excess cord in the

cord wrap feature built into the bottom of the sanitiser. (Fig. 12)

ENGLISH 13

Sanitising (specic types only)

- With the UV sanitiser you can clean your brush head after every use

(Fig. 13).

Discontinue use of the sanitiser if the UV light bulb remains on when

the door is open or if the blue window is broken or missing from the

sanitiser. UV light can be harmful to the human eye and skin.

This appliance should be kept out of reach of children at all times.

Unplug the sanitiser and call Consumer Care if the sanitiser gives off

smoke or a burning smell while it is operating.

1 After brushing, rinse the brush head and shake off excess water.

Do not place the travel cap on the brush head during sanitisation.

2 Place your nger in the door recess on top of the sanitiser and pull

open the door (Fig. 14).

3 Place the brush head on one of the 2 pegs in the sanitiser. (Fig. 15)

- Make sure the bristles of the brush head directly face the light bulb.

Note: Only clean Sonicare ProResults brush heads in the sanitiser.

4 Make sure the sanitiser is plugged into the wall socket.

5 Close the door and press the green power on/off button once to

select the UV clean cycle.

Note: You can only switch on the sanitiser if the door is properly closed.

Note: The sanitiser stops if you open the door during the sanitising cycle.

Note: The sanitiser cycle runs for 10 minutes and then automatically switches off.

, The sanitiser is in operation when the blue light glows through

the window.

, When the sanitising cycle is complete, the sanitiser automatically

switches off.

ENGLISH14

Cleaning

Do not clean the brush head, handle, travel charger, charger cover and

the UV sanitiser in the dishwasher.

Toothbrush handle

1 Remove the brush head and rinse the metal shaft area with warm

water (Fig. 16).

Do not push on the rubber seal on the metal shaft with sharp objects,

as this may cause damage.

2 Use a damp cloth to wipe the entire surface of the handle.

Brush head

1 Rinse the brush head and bristles after each use (Fig. 17).

2 Remove the brush head from the handle and rinse the brush head

connection at least once a week with warm water.

Charger

1 Unplug the charger.

2 Use a damp cloth to wipe the surface of the charger.

Sanitiser (specic types only)

Do not clean the sanitiser when the UV light bulb is hot.

For optimal effectiveness, it is recommended to clean the sanitiser weekly.

1 Unplug the sanitiser.

2 Pull the drip tray straight out. Rinse the drip tray and wipe it clean

with a damp cloth (Fig. 18).

3 Clean all reector surfaces with a damp cloth.

4 Remove the protective screen in front of the UV light bulb. (Fig. 19)

To remove the screen, grasp the edges next to the snaps, gently squeeze

and pull it out.

5 Remove the UV light bulb.

To remove the light bulb, grasp it and pull it out of the metal clasp.

ENGLISH 15

6 Clean the protective screen and the UV light bulb with a damp cloth.

7 Reinsert the UV light bulb.

To reinsert the light bulb, align the bottom of the light bulb with the metal

clasp and push the bulb into the clasp.

8 Reinsert the protective screen.

To reinsert the screen, align the pegs on the screen with the slots on the

reective surface near the UV light bulb. Push the screen straight into the

slots on the sanitiser.

Storage

- If you are not going to use the appliance for an extended period of

time, remove the mains plug from the wall socket. Then clean the

appliance and store it in a cool and dry place away from direct sunlight.

You can use the cord wrap feature to store the mains cord neatly.

Replacement

Brush head

- Replace Sonicare brush heads every 3 months to achieve optimal results.

- Use only compatible Sonicare replacement brush heads.

UV light bulb

- You can order replacement UV light bulbs from the Consumer Care

Centre in your country or an authorised Philips service centre.

Recycling

- This symbol on a product means that the product is covered by

European Directive 2012/19/EU (Fig. 20).

- This symbol means that the product contains a built-in rechargeable

battery covered by European Directive 2006/66/EC which cannot be

disposed of with normal household waste. Follow the instructions in

section ‘Removing the rechargeable battery’ to remove the battery (Fig. 21).

- Inform yourself about the local separate collection system for electrical

and electronic products and rechargeable batteries. Follow local rules

ENGLISH16

and never dispose of the product and rechargeable batteries with

normal household waste. Correct disposal of old products and

rechargeable batteries helps prevent negative consequences for

the environment and human health.

Removing the rechargeable battery

Please note that this process is not reversible.

To remove the rechargeable battery, you need a at-head (standard)

screwdriver.

1 To deplete the rechargeable battery of any charge, remove the handle

from the charger, switch on the Sonicare and let it run until it stops.

Repeat this step until you can no longer switch on the Sonicare.

2 Insert a at-head (standard) screwdriver into the slot located at

the bottom of the handle. Turn the screwdriver anticlockwise to

release the bottom cap. (Fig. 22)

3 Hold the handle upside down and push down on the shaft to

release the internal components of the handle (Fig. 23).

4 Insert the screwdriver under the circuit board, next to the battery

connections, and twist to break the connections. Remove the circuit

board and pry the battery from the plastic carrier (Fig. 24).

Guarantee and support

If you need information or support, please visit www.philips.com/

support or read the separate worldwide guarantee leaet.

Guarantee restrictions

The terms of the international guarantee do not cover the following:

- Brush heads.

- Damage caused by use of unauthorised replacement parts.

- Damage caused by misuse, abuse, neglect, alterations or unauthorised

repair.

- Normal wear and tear, including chips, scratches, abrasions,

discolouration or fading.

ENGLISH 17

Frequently asked questions

This chapter lists the questions most frequently asked about the appliance.

If you cannot nd the answer to your question, contact the Consumer

Care Centre in your country.

Question Answer

Why doesn’t the

Sonicare

toothbrush work?

You may need to recharge the Sonicare.

Charge the Sonicare for at least 24 hours.

The socket may not be live. The electricity

supply to sockets in mirror cabinets over

washbasins or shaver sockets in bathrooms may

be cut off when the light is switched off.

You may need to reattach or replace the brush

head.

Why do I feel a

tickling sensation

when I

use the Sonicare?

You may experience a slight tickling/tingling

sensation when you use Sonicare for the rst

time. As you become accustomed to brushing

with the Sonicare, this sensation diminishes.

Why is there a brief

pause in the bristle

motion while I’m

brushing?

This is the Quadpacer feature reminding you to

move to a new section of your mouth. This

feature enables you to spend equal time brushing

all areas of the mouth (see chapter ‘Using the

Sonicare, section ‘Brushing instructions’).

The brush head

chatters against my

teeth. What can I do

about this?

To avoid this, keep the brush head properly

oriented, with the bristles placed on the gumline

at a slight angle.

Why does the

toothbrush seem

less powerful?

You may need to charge the Sonicare.

The Easy-start feature may be on. Deactivate

the Easy-start feature (see chapter ‘Features’).

ENGLISH18

Question Answer

You may need to replace the brush head.

Why doesn’t the

mode button work

during brushing?

Brushing modes should be selected prior to

switching on the Sonicare.

Why doesn’t the UV

sanitiser light go on?

You may need to plug the sanitiser into a live

wall socket.

You may need to shut the sanitiser door.

You may need to replace the UV light bulb

(see chapter ‘Replacement’).

Do I need a special

charger if I travel

with my Sonicare?

The travel charger, the deluxe charger and

the sanitiser can be used at common worldwide

voltages between 100-240V AC, at either 50 or

60Hz. All you need is a simple plug adapter.

Travel tip: The Sonicare battery is designed to

last up to 3 weeks between charges.

ENGLISH 19

20

Въведение

Поздравления за вашата покупка и добре дошли във Philips! За да се

възползвате изцяло от предлаганата от Philips поддръжка,

регистрирайте продукта си на адрес www.philips.bg/welcome.

Важно

Преди да използвате уреда, прочетете внимателно

това ръководство за потребителя и го запазете

за справка в бъдеще.

Опасност

- Пазете зарядното устройство и/или уреда за

дезинфекция далеч от вода. Не го поставяйте

и не го съхранявайте над или в близост до

вода във вана, мивка, леген и т.н. Не потапяйте

зарядното устройство и/или уреда за

дезинфекция във вода или каквато и да е друга

течност. След почистване се уверете, че

зарядното устройство и/или уредът за

дезинфекция е напълно сух, преди да го

включите в контакта на електрическата мрежа.

Предупреждение

- Захранващият кабел не може да бъде заменян.

При повреда в кабела, зарядното устройство

и/или уредът за дезинфекция следва да се

изхвърли.

- С оглед на предотвратяване на злополука,

винаги заменяйте повреденото зарядно

устройство и/или уред за дезинфекция само

с оригинален такъв.

БЪЛГАРСКИ

Leht laaditakse ...

Sonicare HX6921/06 Kasutusjuhend

Sonicare HX6921/06 Kasutusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid