Whirlpool AKZM 6551/IXL Kasutusjuhend

Kategooria
Köök
Tüüp
Kasutusjuhend
Εγχείριδιο χρήσης και συντήρησης
Bruksanvisning och underhållsinstruktioner
Bruks- og vedlikeholdsmanual
Vejledning i brug og rengøring
Käyttö- ja huolto-ohjeet
EL
AKZM 6551
EN1
YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT
This manual and the appliance itself provide important safety warnings, to be read and observed at all times.
All safety warnings give specific details of the potential risk present and
indicate how to reduce risk of injury, damage and electric shock
resulting from improper use of the appliance. Carefully observe the
following instructions:
- The appliance must be disconnected from the power supply before
carrying out any installation work.
- Installation and maintenance must be carried out by a qualified
technician, in compliance with the manufacturers instructions and
local safety regulations. Do not repair or replace any part of the
appliance unless specifically stated in the user manual.
- Power cable replacement must be carried out by a qualified
electrician. Contact an authorized service centre.
- Regulations require that the appliance is earthed.
- The power cable must be long enough for connecting the
appliance, once fitted in its housing, to the main power supply.
- For installation to comply with current safety regulations, an all-
pole disconnect switch with minimum contact gap of 3 mm must
be utilized.
- Do not use multiple plug adaptors if the oven is fitted with a plug.
- Do not use extension leads.
- Do not pull the power supply cable.
- The electrical components must not be accessible to the user after
installation.
- If the surface of the induction plate is cracked, do not use it and
switch off the appliance to avoid the possibility of electric shock
(only for models with induction function).
IMPORTANT SAFETY INSTRUCTIONS
This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others.
All safety warnings are preceded by the danger symbol and the following terms:
DANGER
Indicates a hazardous situation which, if not avoided, will cause serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could cause serious injury.
EN2
- Do not touch the appliance with any wet part of the body and do
not operate it when barefoot.
- This appliance is designed solely for use as a domestic appliance for
cooking food. No other type of use is permitted (e.g.: heating
rooms). The Manufacturer declines all responsibility for
inappropriate use or incorrect setting of the controls.
- This appliance can be used by children from 8 years and above and
persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe
way and understand hazards involved. Children shall not play with
the appliance. Cleaning and user maintenance shall not be made
by children without supervision.
- The accessible parts of the appliance may become very hot during
use. Young children should be kept away from the appliance and
supervised to ensure that they do not play with it.
- The appliance and its accessible parts become hot during use. Care
should be taken to avoid touching heating elements. Children less
than 8 years old shall be kept away, unless continuously supervised.
- During and after use, do not touch the heating elements or interior
surfaces of the appliance - risk of burns. Do not allow the appliance
to come into contact with cloths or other flammable materials until
all the components have cooled sufficiently.
- At the end of cooking, exercise caution when opening the
appliance door, letting the hot air or steam exit gradually before
accessing the oven. When the appliance door is shut, hot air is
vented from the aperture above the control panel. Do not obstruct
the vent apertures.
- Use oven gloves to remove pans and accessories, taking care not to
touch the heating elements.
- Do not place flammable materials in or near the appliance: a fire
may break out if the appliance is inadvertently switched on.
- Do not heat or cook sealed jars or containers in the appliance. The
pressure that builds up inside might cause the jar to explode,
damaging the appliance.
- Do not use containers made of synthetic materials.
EN3
- Overheated oils and fats catch fire easily. Always remain vigilant
when cooking foods rich in fat and oil.
- Never leave the appliance unattended during food drying.
- If alcoholic beverages are used when cooking foods (e.g. rum,
cognac, wine), remember that alcohol evaporates at high
temperatures. As a result, there is a risk that vapours released by the
alcohol may catch fire upon coming into contact with the electrical
heating element.
- Never use steam cleaning equipment.
- Do not touch the oven during the pyrolysis cycle. Keep children
away from the oven during the pyrolysis cycle (only for ovens with
Pyrolysis function).
- Only use the temperature probe recommended for this oven.
- Do not use harsh abrasive cleaners or sharp metal scrapers to clean
the oven door glass since they can scratch the surface, which may
result in shattering of the glass.
- Ensure that the appliance is switched off before replacing the lamp
to avoid the possibility of electric shock.
- Do not use aluminium foil to cover food in the cooking vessel (only
for ovens with cooking vessel supplied).
- Use protective gloves to perform all unpacking and installation
operations.
Scrapping of household appliances
- This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal
regulations. Before scrapping, cut off the power supply cable.
- For further information on the treatment, recovery and recycling of household electrical appliances, contact your
competent local authority, the collection service for household waste or the store where you purchased the appliance.
After unpacking the oven, make sure that it has not been damaged during transport and that the oven door closes properly. In
the event of problems, contact the dealer or your nearest After-sales Service. To prevent any damage, only remove the oven
from its polystyrene foam base at the time of installation.
PREPARING THE HOUSING UNIT
Kitchen units in contact with the oven must be heat resistant (min 90°C).
Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all wood chips and sawdust.
After installation, the bottom of the oven must no longer be accessible.
For correct appliance operation, do not obstruct the minimum gap between the worktop and the upper edge of the oven.
ELECTRICAL CONNECTION
Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The dataplate is on the front
edge of the oven (visible when the door is open).
Power cable replacement (type H05 RR-F 3 x 1.5 mm
2
) must be carried out by a qualified electrician. Contact an
authorized service centre.
INSTALLATION
EN4
GENERAL RECOMMENDATIONS
Before use:
- Remove cardboard protection pieces, protective film and adhesive labels from accessories.
- Remove the accessories from the oven and heat it at 200° for about an hour to eliminate the smell and fumes from the
insulating materials and protective grease.
During use:
- Do not place heavy objects on the door as they could damage it.
- Do not cling to the door or hang anything from the handle.
- Do not cover the inside of the oven with aluminium foil.
- Never pour water into the inside of a hot oven; this could damage the enamel coating.
- Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.
- Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become trapped in the door.
- Do not expose the oven to atmospheric agents.
Disposal of packing material
The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of the packing must
therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.
Scrapping the product
- This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment
(WEEE).
- By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
- The symbol on the product or on the accompanying documentation indicates that it should not be treated as
domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic
equipment.
Energy saving
- Only pre-heat the oven if specified in the cooking table or your recipe.
- Use dark lacquered or enamelled baking moulds as they absorb heat far better.
- Switch the oven off 10/15 minutes before the set cooking time. Food requiring prolonged cooking will continue to cook even
once the oven is switched off.
- This oven, which is intended to come into contact with foodstuffs, complies with European Regulation ( ) n.1935/2004
and has been designed, manufactured and sold in conformity with the safety requirements of the “Low Voltage” directive
2006/95/CE (which replaces 73/23/CEE and subsequent amendments), the protection requirements of “EMC” 2004/108/CE.
The oven does not work:
Check for the presence of mains electrical power and if the oven is connected to the electrical supply.
Turn off the oven and restart it to see if the fault persists.
The door will not open:
Turn off the oven and restart it to see if the fault persists.
Important: during self-cleaning, the oven door will not open. Wait until it unlocks automatically (see paragraph “Cleaning
cycle of ovens with pyrolysis function”).
The electronic programmer does not work:
If the display shows the letter “ ” followed by a number, contact your nearest After-sales Service. Specify in this case the
number that follows the letter “ .
SAFEGUARDING THE ENVIRONMENT
DECLARATION OF CONFORMITY
TROUBLESHOOTING GUIDE
EN5
Before calling the After-Sales Service:
1. See if you can solve the problem yourself with the help of the suggestions given in the “Troubleshooting guide“.
2. Switch the appliance off and back on again it to see if the fault persists.
If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.
Always specify:
a brief description of the fault;
the type and exact model of the oven;
the service number (number after the word Service on the rating plate), located on the right hand edge of the oven cavity
(visible when the oven door is open). The service number is also indicated on the guarantee booklet;
your full address;
your telephone number.
If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used
and repairs carried out correctly).
Oven exterior
IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with
the appliance, clean immediately with a damp cloth.
Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing up detergent to the water. Finish off
with a dry cloth.
Oven interior
IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin enamelled surfaces
and the oven door glass.
After every use, allow the oven to cool then clean it preferably while it is still warm in order to remove built-up dirt and
stains caused by food residues (e.g. food with a high sugar content).
Use proprietary oven detergents and follow the manufacturers instructions to the letter.
Clean the door glass with a suitable liquid detergent. The oven door can be removed to facilitate cleaning (see
MAINTENANCE).
The top heating element of the grill (see MAINTENANCE) can be lowered (some models only) to clean the roof of the oven.
N.B.: during prolonged cooking of foods with a high water content (e.g. pizza, vegetables, etc.) condensation may form
on the inside of the door and around the seal. When the oven is cold, dry the inside of the door with a cloth or sponge.
Accessories:
Soak the accessories in water with washing up detergent immediately after use, handling them with oven gloves if still hot.
Food residues can be easily removed using a brush or sponge.
Cleaning the rear wall and catalytic side panels of the oven (if present):
IMPORTANT: do not use corrosive or abrasive detergents, coarse brushes, pot scourers or oven sprays which could
damage the catalytic surface and ruin its self-cleaning properties.
Operate the oven empty with the fan-assisted function at 200°C for about one hour
Next, leave the appliance to cool down before removing any food residue with a sponge.
Cleaning cycle of ovens with pyrolysis function (if present):
This function burns off spatters produced inside the oven during cooking at a temperature of approx. 500°C. At this high
temperature, the deposits turn into a light ash which can be easily wiped away with a damp cloth, when the oven is cool. Do not
select the pyrolysis function after every use, only when the oven is very dirty or produces smoke or fumes while preheating or
cooking.
If the oven is installed below a hob, make sure that all burners or electric hotplates are switched off during the self-
cleaning (pyrolysis) function.
AFTER-SALES SERVICE
CLEANING
WARNING
- Never use steam cleaning equipment.
- Only clean the oven when it is cool to the touch.
- Disconnect the appliance from the power supply.
WARNING
- Do not touch the oven during the pyrolysis cycle.
- Keep children away from the oven during the pyrolysis cycle.
EN6
Remove all accessories before running the pyrolysis function.
For optimum cleaning of the oven door, remove the worst soiling with a damp sponge before using the pyrolytic function.
The appliance is equipped with 2 pyrolysis functions:
1. Energy-saving cycle (PYRO EXPRESS/ECO): which consumes approximately 25% less energy than the standard cycle.
Select it at regular intervals (after cooking meat on 2 or 3 consecutive occasions).
2. Standard cycle (PYRO): which is suitable for cleaning a very dirty oven.
In any case, after a certain number of uses and depending on how dirty the oven is, a message on the oven display advises
you to run a self-cleaning cycle.
N.B.: during the pyrolysis function, the oven door will not open; it will remain locked until the temperature inside the
oven has returned to an acceptably safe level.
REMOVING THE DOOR
To remove the door:
1. Open the door fully.
2. Lift the catches and push them forwards as far as they will go (fig. 1).
3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (fig. 2).
To refit the door:
1. Insert the hinges in their seats.
2. Open the door fully.
3. Lower the two catches.
4. Close the door.
MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)
1. Remove the side accessory holder grilles (Fig. 3).
2. Pull the heating element out a little (Fig. 4) and lower it (Fig. 5).
3. To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to rest on the lateral
supports.
REPLACING THE OVEN LAMP
To replace the rear lamp (if present):
1. Disconnect the oven from the power supply.
2. Unscrew the lamp cover (Fig. 6), replace the lamp (see note for lamp type) and screw the lamp cover back on.
3. Reconnect the oven to the power supply.
To replace the side lamp (if present):
1. Disconnect the oven from the power supply.
2. Remove the side accessory holder grilles, if present (Fig. 3).
3. Use a screwdriver to prise off the lamp cover (Fig. 7).
4. Replace the lamp (see note for lamp type) (Fig. 8).
5. Reposition the lamp cover, pushing it on firmly until it snaps into place (Fig. 9).
MAINTENANCE
WARNING
- Use safety gloves.
- Ensure the oven is cold before carrying out the following operations.
- Disconnect the oven from the power supply.
Fig. 1 Fig. 2
Fig. 3 Fig. 4 Fig. 5
EN7
6. Refit the side accessory holder grilles.
7. Reconnect the oven to the power supply.
N.B.:
- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230 V type G9, T300°C halogen lamps.
- The lamp used in the appliance is specifically designed for electrical appliances and is not suitable for household room
illumination (Commission Regulation (EC) No 244/2009).
- Lamps are available from our After-sales Service.
IMPORTANT:
- If using halogen lamps, do not handle with bare hands since fingerprints can damage them.
- Do not use the oven until the lamp cover has been repositioned.
Fig. 6 Fig. 7 Fig. 8 Fig. 9
EN8
FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION
1. Control panel
2. Upper heating element/grill
3. Cooling fan (not visible)
4. Dataplate (not to be removed)
5. Lamps
6. Circular heating element (not visible)
7. Fan
8. Turnspit (if present)
9. Lower heating element (not visible)
10. Door
11. Position of shelves (the number of shelves is indicated on the front of the oven)
12. Rear wall
N.B.:
- During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.
- At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a
while.
- When the oven door is opened during cooking, the heating elements switch off.
ACCESSORIES SUPPLIED
A. WIRE SHELF: the wire shelf can be used to grill food or as a support for pans, cake tins and other
ovenproof cooking receptacles.
B. DRIP TRAY: the drip tray is designed to be positioned under the wire shelf in order to collect fat or as
an oven tray for cooking meat, fish, vegetables, focaccia, etc.
The number of accessories may vary according to which model is purchased.
ACCESSORIES NOT SUPPLIED
Other accessories can be purchased separately from the After-sales Service.
INSTRUCTIONS FOR OVEN USE
Fig. A Fig. B
EN9
INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN
The wire shelf and other accessories are provided with a locking mechanism to prevent their accidental
removal.
1. Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).
2. Angle the wire shelf when it reaches the locking position “B” (Fig. 2).
3. Return the wire shelf to the horizontal position and push it in fully to “C” (Fig. 3).
4. To remove the wire shelf proceed in reverse order.
The other accessories, like the drip tray and baking tray, are inserted in exactly the same way.
The protrusion on the flat surface enables the accessories to lock in place.
CONTROL PANEL DESCRIPTION
ELECTRONIC PROGRAMMER
1. FUNCTION SELECTOR KNOB: on/off and function selector knob
2. BROWSE KNOB: for browsing the menu and adjusting pre-set values
N.B.:the two knobs are retractable. Press the knobs in the middle and they pop up.
3. BUTTON : to return to the previous screen
4. BUTTON : to select and confirm settings
LIST OF FUNCTIONS
Turn the “Functions” knob to any position and the oven switches on: the display shows the functions or the
associated submenus.
The submenus are available and selectable by turning the knob to the functions GRILL, SPECIALS,
SETTINGS, RECIPES and FAVOURITES.
A. Symbol for highlighted function
B. Highlighted function can be selected by pressing
C. Description of highlighted function
D. Other available and selectable functions.
Fig. 1
Fig. 2 Fig. 3
1 23 4
Specials: For defrosting food
Warm Keeping
Frozen Food
Defrost
DISPLAY
Specials: For defrosting food
Warm Keeping
Frozen Food
Defrost
A
D
C
B
EN10
DETAILS OF FUNCTION
After selection of the desired function, the display will show further options and related details.
To move between the different areas, turn the “Browse” knob: the cursor moves to the adjustable values,
following the order described above. Press button to select the value, change it by turning the “Browse”
knob and confirm with button .
USING THE APPLIANCE FOR THE FIRST TIME - LANGUAGE SELECTION AND SETTING
THE TIME
For correct use of the oven, when it is switched on for the first time you will have to select the desired
language and set the correct time.
Proceed as follows:
1. Turn the “Functions” knob to any position: the display will show the list of the first three available
languages.
2. Turn the “Browse” knob to scroll the list.
3. When the desired language is highlighted, press to select it.
After language selection, the display will flash 12:00.
4. Set the time by turning the “Browse” knob.
5. Confirm your setting by pressing .
SELECTING COOKING FUNCTIONS
1. If the oven is off, turn the “Functions” knob; the display will show the cooking functions or associated
submenus.
N.B.:for the list and description of functions, see the specific table at page14 and at page15.
2. Within the submenus, browse the various options available by turning the “Browse” knob: the chosen
function is highlighted in white in the centre of the screen. To select it, press .
3. the cooking settings are displayed on the screen. If the pre-set values are those desired, turn the
“Browse” knob to position the cursor at “Start” and then press ; otherwise, proceed as indicated
above to change them.
SETTING THE TEMPERATURE/OUTPUT OF THE GRILL
To change the temperature or output of the grill, proceed as follows:
1. Check that the cursor is positioned next to the temperature value (zone 1); press button to select
the parameter to be changed: the temperature values flash.
2. Set the desired value by turning the “Browse” knob and press to confirm.
3. Turn the “Browse” knob to position the cursor at “Start” and then press .
4. The display indicates which shelf food should be placed on. Do as instructed and press to start
cooking.
The set temperature can also be changed during cooking by following the same procedure.
Zone 3 Zone 4
Zone 5
Zone 2
Zone 1Cursor
PREHEAT
Yes
TEMPERATURE
180°C
COOK TIME
END TIME
Convection Bake
--:--
--:--
Start
PREHEAT
Yes
TEMPERATURE
180°C
COOK TIME
END TIME
Convection Bake
--:--
--:--
Start
PREHEAT
Yes
TEMPERATURE
180°C
COOK TIME
END TIME
Convection Bake
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
200°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
200°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
EN11
5. At the end of cooking, the end of cooking message is displayed. At this point the oven can be
switched off by turning the “Functions” knob to 0 (zero), or cooking can be prolonged by turning the
“Browse” knob clockwise. When switched off, the display shows the cooling bar which indicates the
temperature inside the oven.
PREHEATING THE OVEN
If you wish to preheat the oven before inserting food, change the oven’s default selection as follows:
1. Turn the “Browse” knob to position the cursor at preheating.
2. Press button to select the setting: “No” flashes on the display.
3. Change the setting by turning the “Browse” knob: the display shows “Yes”.
4. To confirm your choice, press button .
FAST PREHEATING
If you wish to preheat the oven quickly before inserting food, change the oven’s default selection as
follows:
1. Turn the “Functions” knob to select the fast preheating function.
2. Confirm by pressing : the settings are displayed on the screen.
3. If the proposed temperature is that desired, turn the “Browse” knob to position the cursor at “Start” and
then press . To change the temperature, proceed as described in previous paragraphs. An acoustic signal
will sound when the oven has reached the set temperature. At the end of preheating, the oven
automatically selects the conventional function .
At this point food can be placed in the oven for cooking.
4. If you wish to set a different cooking function, turn the “Functions” knob and select the desired
function.
SETTING COOKING TIME
This function can be used to cook food for a set length of time, from a minimum of 1 minute to the
maximum time allowed by the selected function, after which the oven switches off automatically.
1. To select the function, turn the “Browse” knob to position the cursor at “cooking duration.
2. Press button to select the setting; “00:00” flashes on the display.
3. Change the value by turning the “Browse” knob to display the desired cooking time.
4. Confirm the selected value by pressing button .
BROWNING
At the end of cooking, with certain functions, the display indicates the possibility of browning the surface of
your dish. This function can only be used when cooking time has been set.
At the end of cooking time, the display shows “+/- to prolong, to brown”. Press button , and the oven
starts a 5 minute browning cycle. This function can only be used once after cooking.
PREHEAT
No
TEMPERATURE
200°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
200°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
Ye s
TEMPERATURE
200°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
Ye s
TEMPERATURE
200°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
TEMPERATURE
180°C
Turn +/- to adjust ...
Start
Specials: For defrosting food
Warm Keeping
Frozen Food
Defrost
Browning
COOK TIME
END TIME
20:05
- 00:05
Cooking nished at 20:00
+/- to prolong, to brown
Browning nished at 20:05
EN12
SETTING END OF COOKING TIME / DELAYED START
The end of cooking time can be set, delaying the start of cooking by up to a maximum of 23 hours and
59 minutes. This can only be done once cooking time has been set. This setting is only possible when
pre-heating is not required for the selected function.
After setting cooking time, the display shows the end of cooking time (for example 19:20). To delay the end
of cooking time, and thus also the cooking start time, proceed as follows:
1. Turn the “Browse” knob to position the cursor at the end of cooking time.
2. Press button to select the setting: the end of cooking time flashes.
3. To delay the end of cooking time, turn the “Browse” knob to set the desired value.
4. Confirm the selected value by pressing button .
5. Turn the “Browse” knob to position the cursor at START and then press .
6. The display indicates which shelf food should be placed on. Do as instructed and press to start
cooking. The oven will start cooking after a period of time calculated so as to finish cooking at the set
time (for example, in the case of a dish which requires a cooking time of 20 minutes, if the end of
cooking time is set to 20:10, the oven will begin cooking at 19:50).
N.B.:during the interval before cooking starts, the oven can in any case be switched on by turning
the “Browse” knob to position the cursor at “Start” and then pressing .
At any time, set values (temperature, grill setting, cooking time) can be changed as described in
previous paragraphs.
TIMER
This function can be used only with the oven switched off and is useful, for example, for monitoring the
cooking time of pasta. The maximum time which can be set is 1 hour 30 minutes.
1. With the oven switched off, press button : the display will show “00:00:00”.
2. Turn the “Browse” knob to select the desired time.
3. Press button to start the countdown. When the set time has elapsed, the display will show
“00:00:00” and an acoustic signal will sound. At this point the time can be prolonged, proceeding as
described above, or the timer can be deactivated by pressing button (the time of day will be shown
on the display).
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
19:20
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
19:20
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
20:10
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
20:10
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
20:10
- 00:29
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
20:10
- 00:30
Start
Turn +/- to set Timer, to Start
00 : 00 : 00
(HH) (MM) (SS)
Turn +/- to set Timer, to Start
00 : 30 : 00
(HH) (MM) (SS)
Timer
01 : 09 : 00
EN13
RECIPES
Thanks to “Sixth sense” technology, the oven offers 30 pre-set recipes with ideal cooking temperatures.
Simply follow the recipe as regards ingredients and the method of preparation. Then, proceed as follows:
1. Select “RECIPES” by turning the “Functions” knob.
2. Select the dish to be cooked from the proposed list.
3. Confirm the selected dish using button .
4. Select the desired recipe by turning the “Browse” knob.
5. Confirm by pressing : the display shows the approximate cooking time.
6. Place the dish in the oven and turn the “Browse” knob to position the cursor at “Start”, then press .
7. The display indicates which shelf food should be placed on. Do as instructed and press to start
cooking. To delay the start of cooking, see the relevant paragraph.
N.B.:some dishes must be turned or stirred half way through cooking: the oven will emit an acoustic
signal and the display will indicate what action is required.
The initial cooking time displayed is merely for guidance: it can be prolonged automatically during
cooking.
Shortly before cooking time finishes, the oven prompts you to check that the food is cooked to your
satisfaction. If it is not, extra time can then be added manually by turning the “Browse” knob.
SETTINGS
1. To change some display settings, select “SETTINGS” from the main menu by turning the “Functions”
knob.
2. Confirm by pressing : the display shows which settings can be changed (language, volume of
acoustic signal, display brightness, time, energy saving function).
3. Select the setting to be changed by turning the “Browse” knob.
4. Press button to confirm.
5. Follow the instructions of the display to change the settings.
6. Press button ; a message appears on the display confirming your selection.
N.B.: When the oven is switched off, if the ECOMODE (Energy saving) function is selected (ON), the display
switches off after a few seconds, showing the clock. To view information on the display and switch the light
on again, just press any of the buttons or turn one of the knobs. During a cooking function if the ECOMODE
is activated the cavity lamp will be switched off after 1 minute of cooking and reactivated for each user
interaction. If, on the other hand, the function is not selected (OFF), after a few minutes the display is merely
dimmed.
KEY-LOCK
This function can be used to lock the buttons and knobs on the control panel.
To activate it, press and at the same time for at least 3 seconds. If activated, the functions of the
buttons are locked and the display shows a message and the symbol . This function can also be activated
during cooking. To deactivate it, repeat the above procedure. When the key-lock function is activated, the
oven can be switched off by turning the knob to 0 (zero). In this case, however, the previously selected
function will have to be set again.
CONTROL
Automatic
COOK TIME
END TIME
Pork Chops
19:20
- 00:32
Start
Insert food on level 3
Press
when done
6th Sense: Press to view recipes
Fish
Dessert
Meat
6th Sense: Press to view recipes
Fish
Dessert
Meat
6th Sense: See cookbook for description
Shank of Pork
Kebabs
Pork Chops
6th Sense: See cookbook for description
Shank of Pork
Kebabs
Pork Chops
Please turn food
Cooking nearly nished
Please check on food
Cooking Finished at 19:45
Press to Prolong Cooking
EN14
FUNCTION DESCRIPTION TABLE
FUNCTION SELECTOR KNOB
OFF To halt cooking and switch off the oven.
LAMP To switch the oven interior light on/off.
FAST PREHEATING To preheat the oven rapidly.
CONVENTIONAL
To cook any kind of dish on one shelf only. Use the 3rd shelf. To cook pizza,
savoury pies and sweets with liquid fillings, use the 1st or 2nd shelf.
The oven does not have to be preheated.
GRILL
To grill steak, kebabs and sausages; to cook vegetables au gratin and toast
bread. Place food on the 4th or 5th shelf. When grilling meat, use the drip
tray to collect the cooking juices. Position it on the 3rd/4th shelf, adding
approx. half a litre of water. The oven does not have to be preheated.
During cooking the oven door must remain closed.
TURBO GRILL
To roast large joints of meat (legs, roast beef, chickens). Position the food
on the middle shelves. Use the drip tray to collect the cooking juices.
Position it on the 1st/2nd shelf, adding approx. half a litre of water. The
oven does not have to be preheated. During cooking the oven door must
remain closed. With this function you can also use the turnspit, if provided.
FORCED AIR
To cook a variety of food requiring the same cooking temperature on
several shelves (maximum three) at the same time (e.g. fish, vegetables,
cakes). This function can be used to cook different foods without odours
being transferred from one food to another. Use the 3rd shelf to cook on
one shelf only, the 1st and 4th to cook on two shelves, and the 1st, 3rd and
5th to cook on three shelves. The oven does not have to be preheated.
CONVECTION BAKE
To cook meat and pies with liquid filling (savoury or sweet) on a single
shelf. Use the 3rd shelf. The oven does not have to be preheated.
SPECIALS See SPECIAL FUNCTIONS.
SETTINGS
Setting the display (language, time, brightness, volume of acoustic signal,
energy saving function).
RECIPES
Selecting 30 different pre-set recipes (see enclosed recipe booklet).
The oven automatically sets the optimum cooking temperature, function
and time. It is important to follow the instructions given in the recipe book
regarding preparation, accessories and which oven shelf to use.
FAVOURITES
To directly access the 10 most used functions. To change the settings of
the desired function, see paragraph “SELECTING COOKING FUNCTIONS”.
EN15
SPECIAL
DEFROST
To speed up defrosting of food. Place food on the middle shelf. Leave food
in its packaging in order to prevent it from drying out on the outside.
KEEP WARM
For keeping just-cooked food hot and crisp (e.g: meat, fried food or flans).
Place food on the middle shelf. The function will not activate if the
temperature in the oven is above 65°C.
RISING
For optimal rising of sweet or savoury dough. To safeguard the quality of
proving, the function will not activate if the temperature in the oven is
above 40°C. Place the dough on the 2nd shelf. The oven does not have to
be preheated.
CONVENIENCE
Cooking ready meals kept at room temperature or from refrigerated
cabinets (biscuits, liquid cake mixtures, muffins, first courses and bakery
products). This function gently cooks all food quickly; it can also be used to
reheat cooked food. Follow the instructions on the food packaging.
The oven does not have to be preheated.
MAXI COOKING
To cook large joints of meat (above 2.5 kg). Use the 1st or 2rd shelves,
depending on the size of the joint. The oven does not have to be
preheated. It is advisable to turn the meat over during cooking, to obtain
even browning on both sides. It is preferable to baste the meat every now
and again so that it does not become too dry.
FROZEN
FOOD
Lasagne
The function automatically selects the ideal cooking temperature and
mode for 5 different types of ready frozen food. Use the 2nd or 3rd shelf.
The oven does not have to be preheated.
Pizza
Strudel
French
Fries
Bread
Custom
The temperature can be set from 50 to 250°C to cook other types of
product.
ECO FORCED AIR
To cook stuffed roasts and meat in pieces on one shelf. This function uses
discontinuous, delicate fan assistance, which prevents excessive drying of
foods. In this ECO function the light remains off during cooking and can be
temporarily switched on again by pressing the confirm button. In order to
maximize energy efficiency, it is advisable not to open the door during
cooking. It is advisable to use 3rd level. The oven does not have to be
preheated.
EN16
COOKING TABLE
Recipe Function Pre-
heating
Shelf (from
bottom)
Temp.
(°C)
Time
(min)
Accessories and notes
Leavened cakes
- 2 / 3 160-180 30-90 Cake tin on rack
- 1-4 160-180 30-90
Level 4: cake tin on rack
Level 1: cake tin on rack
Filled pies
(cheesecake, strudel,
apple pie)
- 3 160-200 35-90
Drip-tray / baking tray or
cake tin on rack
- 1-4 160-200 40-90
Level 4: cake tin on rack
Level 1: cake tin on rack
Biscuits / Tartlets
- 3 170-180 20-45 Drip-tray or baking tray
- 1-4 160-170 20-45
Level 4: rack
Level 1: drip-tray or baking
tray
- 1-3-5 160-170 20-45*
Level 5: pan on rack
Level 3: pan on rack
Level 1: drip-tray or baking
tray
Choux buns
- 3 180-200 30-40 Drip-tray or baking tray
- 1-4 180-190 35-45
Level 4: pan on rack
Level 1: drip-tray or baking
tray
- 1-3-5 180-190 35-45*
Level 5: pan on rack
Level 3: pan on rack
Level 1: drip-tray or baking
tray
Meringues
- 3 90 110-150 Drip-tray or baking tray
- 1-4 90 140-160
Level 4: pan on rack
Level 1: drip-tray or baking
tray
- 1-3-5 90 140-160*
Level 5: pan on rack
Level 3: pan on rack
Level 1: drip-tray or baking
tray
Bread / Pizza /
Focaccia
-1 / 2190-250 15-50 Drip-tray or baking tray
- 1-4 190-250 20-50
Level 4: pan on rack
Level 1: drip-tray or baking
tray
- 1-3-5 190-250 25-50*
Level 5: pan on rack
Level 3: pan on rack
Level 1: drip-tray or baking
tray
EN17
Savoury pies
(vegetable pie,
quiche lorraine)
- 3 180-190 40-55 Cake tin on rack
- 1-4 180-190 45-70
Level 4: cake tin on rack
Level 1: cake tin on rack
- 1-3-5 180-190 45-70*
Level 5: cake tin on rack
Level 3: cake tin on rack
Level 1: drip-tray or baking
tray + cake tin
Vols-au-vent /
Puff pastry savouries
- 3 190-200 20-30 Drip-tray or baking tray
- 1-4 180-190 20-40
Level 4: pan on rack
Level 1: drip-tray or baking
tray
- 1-3-5 180-190 20-40*
Level 5: pan on rack
Level 3: pan on rack
Level 1: drip-tray or baking
tray
Lasagna / Baked
pasta / Cannelloni /
Flans
- 3 190-200 45-55 Pan on rack
Lamb / Veal / Beef /
Pork 1 Kg
- 3 190-200 80-110 Drip-tray or pan on rack
Chicken / Rabbit /
Duck 1 Kg
- 3 200-230 50-100 Drip-tray or pan on rack
Turkey / Goose 3 Kg - 2 190-200 80-130 Drip-tray or pan on rack
Baked fish /
en papillote
(fillet, whole)
- 3 180-200 40-60 Drip-tray or pan on rack
Stuffed vegetables
(tomatoes,
courgettes,
aubergines)
- 2 180-200 50-60 Pan on rack
Toas t - 5 High 3-6 Rack
Fish fillets / steaks - 4 Medium 20-30
Level 4: rack (turn food
halfway through cooking)
Level 3: drip-tray with water
Sausages / Kebabs /
Spare ribs /
Hamburgers
- 5
Medium-
High
15-30
Level 5: rack (turn food
halfway through cooking)
Level 4: drip-tray with water
Roast chicken
1-1.3 Kg
- 2 Medium 55-70
Level 2: rack (turn food two
thirds of the way through
cooking)
Level 1: drip-tray with water
- 2 High 60-80
Level 2: turnspit (if present)
Level 1: drip-tray with water
Roast beef rare 1 Kg - 2 Medium 40-50
Pan on rack (turn food two
thirds of the way through
cooking if necessary)
Recipe Function Pre-
heating
Shelf (from
bottom)
Temp.
(°C)
Time
(min)
Accessories and notes
EN18
* Cooking time is approximate. Food can be removed from the oven at different times depending on
personal preference.
Leg of lamb / Shanks - 3 Medium 60-90
Drip-tray or pan on rack
(turn food two thirds of the
way through cooking if
necessary)
Baked potatoes - 3 Medium 45-55
Drip-tray or baking tray
(turn food two thirds of the
way through cooking if
necessary)
Vegetables au gratin - 3 High 10-15 Pan on rack
Lasagna & Meat - 1-4 200 50-100*
Level 4: pan on rack
Level 1: drip-tray or pan on
rack
Meat & Potatoes - 1-4 200 45-100*
Level 4: pan on rack
Level 1: drip-tray or pan on
rack
Fish & Vegetables - 1-4 180 30-50*
Level 4: pan on rack
Level 1: drip-tray or pan on
rack
Complete meal:
Tart (Level 5) /
Lasagna (Level 3) /
Meat (Level 1)
- 1-3-5 190 40-120*
Level 5: pan on rack
Level 3: pan on rack
Level 1: drip-tray or pan on
rack
Frozen pizza
- 3 Auto 10-15
Drip-tray / baking tray or
rack
- 1-4 Auto 15-20
Level 4: pan on rack
Level 1: drip-tray or baking
tray
- 1-3-5 Auto 20-30
Level 5: pan on rack
Level 3: drip-tray or baking
tray
Level 1: pan on rack
- 1-3-4-5 Auto 20-30
Level 5: pan on rack
Level 4: drip-tray or baking
tray
Level 3: drip-tray or baking
tray
Level 1: pan on rack
Filled roast meats - 3 200 80-120* Drip-tray or pan on rack
Meat cuts (rabbit,
chicken, lamb)
- 3 200 50-100* Drip-tray or pan on rack
Recipe Function Pre-
heating
Shelf (from
bottom)
Temp.
(°C)
Time
(min)
Accessories and notes
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Whirlpool AKZM 6551/IXL Kasutusjuhend

Kategooria
Köök
Tüüp
Kasutusjuhend

teistes keeltes