User and maintenance manual
Bruksanvisning och underhållsinstruktioner
Bruks- og vedlikeholdsmanual
Vejledning i brug og rengøring
Käyttö- ja huolto-ohjeet
EN
DA
EN1
These instructions shall also be available on website: www.whirlpool.eu
YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT
This manual and the appliance itself provide important safety warnings, to be read and observed at all times.
All safety warnings give specific details of the potential risk present
and indicate how to reduce risk of injury, damage and electric shock
resulting from improper use of the appliance. Carefully observe the
following instructions:
- Use protective gloves to perform all unpacking and installation
operations.
- The appliance must be disconnected from the power supply before
carrying out any installation work.
- Installation and maintenance must be carried out by a qualified
technician, in compliance with the manufacturer’s instructions and
local safety regulations. Do not repair or replace any part of the
appliance unless specifically stated in the user manual.
- Power cable replacement must be carried out by a qualified
electrician. Contact an authorized service centre.
- Regulations require that the appliance is earthed.
- The power cable must be long enough for connecting the
appliance, once fitted in its housing, to the main power supply.
- For installation to comply with current safety regulations, an all-
pole disconnect switch with minimum contact gap of 3 mm must
be utilized.
- Do not use multiple plug adaptors if the oven is fitted with a plug.
- Do not use extension leads.
- Do not pull the power supply cable.
- The electrical components must not be accessible to the user after
installation.
IMPORTANT SAFETY INSTRUCTIONS
This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others.
All safety warnings are preceded by the danger symbol and the following terms:
DANGER
Indicates a hazardous situation which, if not avoided, will cause serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could cause serious injury.
EN2
- If the surface of the induction plate is cracked, do not use it and
switch off the appliance to avoid the possibility of electric shock
(only for models with induction function).
- Do not touch the appliance with any wet part of the body and do
not operate it when barefoot.
- This appliance is designed solely for use as a domestic appliance
for cooking food. No other type of use is permitted (e.g.: heating
rooms). The Manufacturer declines all responsibility for
inappropriate use or incorrect setting of the controls.
- The appliance and its accessible parts become hot during use.
Care should be taken to avoid touching heating elements.
Very young (0-3 years) and young children (3-8 years) shall
be kept away unless continuously supervised.
- Children from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and
knowledge can use this appliance only if they are supervised or
have been given instructions on safe appliance use and if they
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by
children without supervision.
- During and after use, do not touch the heating elements or interior
surfaces of the appliance - risk of burns. Do not allow the appliance
to come into contact with cloths or other flammable materials until
all the components have cooled down completely.
- At the end of cooking, exercise caution when opening the
appliance door, letting the hot air or steam exit gradually before
accessing the oven. When the appliance door is shut, hot air is
vented from the aperture above the control panel. Do not obstruct
the vent apertures.
- Use oven gloves to remove pans and accessories, taking care not to
touch the heating elements.
- Do not place flammable materials in or near the appliance: a fire
may break out if the appliance is inadvertently switched on.
- Do not heat or cook sealed jars or containers in the appliance.
The pressure that builds up inside might cause the jar to explode,
damaging the appliance.
EN3
- Do not use containers made of synthetic materials.
- Overheated oils and fats catch fire easily. Always remain vigilant
when cooking foods rich in fat and oil.
- Never leave the appliance unattended during food drying.
- If alcoholic beverages are used when cooking foods (e.g. rum,
cognac, wine), remember that alcohol evaporates at high
temperatures. As a result, there is a risk that vapours released
by the alcohol may catch fire upon coming into contact with the
electrical heating element.
- Never use steam cleaning equipment.
- Do not touch the oven during the pyrolysis cycle. Keep children
away from the oven during the pyrolysis cycle. Excess spillage must
be removed from the oven cavity before cleaning cycle (only for
ovens with Pyrolysis function).
- Only use the temperature probe recommended for this oven.
- Do not use harsh abrasive cleaners or sharp metal scrapers to clean
the oven door glass since they can scratch the surface, which may
result in shattering of the glass.
- Ensure that the appliance is switched off before replacing the lamp
to avoid the possibility of electric shock.
- Do not use aluminium foil to cover food in the cooking vessel (only
for ovens with cooking vessel supplied).
Scrapping of household appliances
- This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal
regulations. Before scrapping, cut off the power supply cable.
- For further information on the treatment, recovery and recycling of household electrical appliances, contact your
competent local authority, the collection service for household waste or the store where you purchased the appliance.
After unpacking the oven, make sure that it has not been damaged during transport and that the oven door closes properly. In
the event of problems, contact the dealer or your nearest After-sales Service. To prevent any damage, only remove the oven
from its polystyrene foam base at the time of installation.
PREPARING THE HOUSING UNIT
• Kitchen units in contact with the oven must be heat resistant (min 90°C).
• Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all wood chips and sawdust.
• After installation, the bottom of the oven must no longer be accessible.
• For correct appliance operation, do not obstruct the minimum gap between the worktop and the upper edge of the oven.
ELECTRICAL CONNECTION
Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The dataplate is on the front
edge of the oven (visible when the door is open).
• Power cable replacement (type H05 RR-F 3 x 1.5 mm
2
) must be carried out by a qualified electrician. Contact an
authorized service centre.
INSTALLATION
EN4
GENERAL RECOMMENDATIONS
Before use:
- Remove cardboard protection pieces, protective film and adhesive labels from accessories.
- Remove the accessories from the oven and heat it at 200° for about an hour to eliminate the smell and fumes from the
insulating materials and protective grease.
During use:
- Do not place heavy objects on the door as they could damage it.
- Do not cling to the door or hang anything from the handle.
- Do not cover the inside of the oven with aluminium foil.
- Never pour water into the inside of a hot oven; this could damage the enamel coating.
- Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.
- Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become trapped in the door.
- Do not expose the oven to atmospheric agents.
Disposal of packing material
The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of the packing must
therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.
Scrapping the product
- This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment
(WEEE).
- By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
- The symbol on the product or on the accompanying documentation indicates that it should not be treated as
domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic
equipment.
Energy saving
- Only pre-heat the oven if specified in the cooking table or your recipe.
- Use dark lacquered or enamelled baking moulds as they absorb heat far better.
- Switch the oven off 10/15 minutes before the set cooking time. Food requiring prolonged cooking will continue to cook even
once the oven is switched off.
- This oven, which is intended to come into contact with foodstuffs, complies with European Regulation ( ) n.1935/2004
and has been designed, manufactured and sold in conformity with the safety requirements of the “Low Voltage” directive
2006/95/CE (which replaces 73/23/CEE and subsequent amendments), the protection requirements of “EMC” 2004/108/
CE.
The oven does not work:
• Check for the presence of mains electrical power and if the oven is connected to the electrical supply.
• Turn off the oven and restart it to see if the fault persists.
The door will not open:
• Turn off the oven and restart it to see if the fault persists.
• Important: during self-cleaning, the oven door will not open. Wait until it unlocks automatically (see paragraph “Cleaning
cycle of ovens with pyrolysis function”).
The electronic programmer does not work:
• If the display shows the letter “ ” followed by a number, contact your nearest After-sales Service. Specify in this case the
number that follows the letter “ ”.
SAFEGUARDING THE ENVIRONMENT
DECLARATION OF CONFORMITY
TROUBLESHOOTING GUIDE
EN5
Before calling the After-Sales Service:
1. See if you can solve the problem yourself with the help of the suggestions given in the “Troubleshooting guide“.
2. Switch the appliance off and back on again it to see if the fault persists.
If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.
Always specify:
• a brief description of the fault;
• the type and exact model of the oven;
• the service number (number after the word Service on the rating plate), located on the right hand edge of the oven cavity
(visible when the oven door is open). The service number is also indicated on the guarantee booklet;
• your full address;
• your telephone number.
If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used
and repairs carried out correctly).
Oven exterior
IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with
the appliance, clean immediately with a damp microfibre cloth.
• Clean the surfaces with a damp microfibre cloth. If it is very dirty, add a few drops of washing up detergent to the water.
Finish off with a dry cloth.
Oven interior
IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin enamelled surfaces
and the oven door glass.
• After every use, allow the oven to cool then clean it preferably while it is still warm in order to remove built-up dirt and
stains caused by food residues (e.g. food with a high sugar content).
• Use proprietary oven detergents and follow the manufacturer’s instructions to the letter.
• Clean the door glass with a suitable liquid detergent. The oven door can be removed to facilitate cleaning (see
MAINTENANCE).
• The top heating element of the grill (see MAINTENANCE) can be lowered (some models only) to clean the roof of the oven.
N.B.: during prolonged cooking of foods with a high water content (e.g. pizza, vegetables, etc.) condensation may form
on the inside of the door and around the seal. When the oven is cold, dry the inside of the door with a cloth or sponge.
Accessories:
• Soak the accessories in water with washing up detergent immediately after use, handling them with oven gloves if still
hot.
• Food residues can be easily removed using a brush or sponge.
Cleaning the rear wall and catalytic side panels of the oven (if present):
IMPORTANT: do not use corrosive or abrasive detergents, coarse brushes, pot scourers or oven sprays which could
damage the catalytic surface and ruin its self-cleaning properties.
• Operate the oven empty with the fan-assisted function at 200°C for about one hour
• Next, leave the appliance to cool down before removing any food residue with a sponge.
Cleaning cycle of ovens with pyrolysis function:
This function burns off spatters produced inside the oven during cooking at a temperature of approx. 500°C. At this high
temperature, the deposits turn into a light ash which can be easily wiped away with a damp cloth, when the oven is cool. Do not
select the pyrolysis function after every use, only when the oven is very dirty or produces smoke or fumes while preheating or
cooking.
AFTER-SALES SERVICE
CLEANING
WARNING
- Never use steam cleaning equipment.
- Only clean the oven when it is cool to the touch.
- Disconnect the appliance from the power supply.
WARNING
- Do not touch the oven during the pyrolysis cycle.
- Keep children away from the oven during the pyrolysis cycle.
EN6
• If the oven is installed below a hob, make sure that all burners or electric hotplates are switched off during the self-
cleaning (pyrolysis) function.
• Remove all accessories before running the pyrolysis function (also the lateral grids).
• For optimum cleaning of the oven door, remove the worst soiling with a damp sponge before using the pyrolytic function.
The appliance is equipped with 2 pyrolysis functions:
1. Energy-saving cycle (PYRO EXPRESS/ECO): which consumes approximately 25% less energy than the standard cycle.
Select it at regular intervals (after cooking meat on 2 or 3 consecutive occasions).
2. Standard cycle (PYRO): which is suitable for cleaning a very dirty oven.
• In any case, after a certain number of uses and depending on how dirty the oven is, a message on the oven display advises
you to run a self-cleaning cycle.
N.B.: during the pyrolysis function, the oven door will not open; it will remain locked until the temperature inside the
oven has returned to an acceptably safe level.
REMOVING THE DOOR
To remove the door:
1. Open the door fully.
2. Lift the catches and push them forwards as far as they will go (fig. 1).
3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (fig. 2).
To refit the door:
1. Insert the hinges in their seats.
2. Open the door fully.
3. Lower the two catches.
4. Close the door.
MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)
1. Remove the side accessory holder grilles (Fig. 3).
2. Pull the heating element out a little (Fig. 4) and lower it (Fig. 5).
3. To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to rest on the lateral
supports.
REPLACING THE OVEN LAMP
To replace the rear lamp (if present):
1. Disconnect the oven from the power supply.
2. Unscrew the lamp cover (Fig. 6), replace the lamp (see note for lamp type) and screw the lamp cover back on.
3. Reconnect the oven to the power supply.
To replace the side lamp (if present):
1. Disconnect the oven from the power supply.
2. Remove the side accessory holder grilles, if present (Fig. 3).
3. Use a screwdriver to prise off the lamp cover (Fig. 7).
MAINTENANCE
WARNING
- Use protective gloves.
- Ensure the oven is cold before carrying out the following operations.
- Disconnect the appliance from the power supply.
Fig. 1 Fig. 2
Fig. 3 Fig. 4 Fig. 5
EN7
4. Replace the lamp (see note for lamp type) (Fig. 8).
5. Reposition the lamp cover, pushing it on firmly until it snaps into place (Fig. 9).
6. Refit the side accessory holder grilles.
7. Reconnect the oven to the power supply.
N.B.:
- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230 V type G9, T300°C halogen lamps.
- The lamp used in the appliance is specifically designed for electrical appliances and is not suitable for household room
illumination (Commission Regulation (EC) No 244/2009).
- Lamps are available from our After-sales Service.
IMPORTANT:
- If using halogen lamps, do not handle with bare hands since fingerprints can damage them.
- Do not use the oven until the lamp cover has been repositioned.
Fig. 6 Fig. 7 Fig. 8 Fig. 9
EN8
FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION
1. Control panel
2. Upper heating element/grill
3. Cooling fan (not visible)
4. Dataplate (not to be removed)
5. Lamps
6. Circular heating element (not visible)
7. Fan
8. Turnspit (if present)
9. Lower heating element (not visible)
10. Door
11. Position of shelves (the number of shelves is indicated on the front of the oven)
12. Rear wall
13. Meat probe connection
N.B.:
- During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.
- At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a
while.
- When the oven door is opened during cooking, the heating elements switch off.
ACCESSORIES SUPPLIED
A. WIRE SHELF: the wire shelf can be used to grill food or as a support for pans, cake tins and other
ovenproof cooking receptacles.
B. DRIP TRAY: the drip tray is designed to be positioned under the wire shelf in order to collect fat or as
an oven tray for cooking meat, fish, vegetables, focaccia, etc.
C. BAKING TRAY: for cooking all bread and pastry products, but also roasts, fish en papillotte, etc.
D. MEAT PROBE: to measure the core temperature of food during cooking.
E. SLIDING RUNNERS: to facilitate insertion and removal of accessories.
The number of accessories may vary according to which model is purchased.
ACCESSORIES NOT SUPPLIED
Other accessories can be purchased separately from the After-sales Service.
INSTRUCTIONS FOR OVEN USE
Fig. A Fig. B Fig. C Fig. D Fig. E
13
EN9
INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN
1. Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).
2. The other accessories, like the drip tray and baking tray, are inserted with the raised part on the flat
section “B” facing upwards (Fig. 2).
CONTROL PANEL DESCRIPTION
ELECTRONIC PROGRAMMER
1. FUNCTION SELECTOR KNOB: on/off and function selector knob
2. BROWSE KNOB: for browsing the menu and adjusting pre-set values
N.B.:the knobs are retractable. Press the knobs in the middle and they pop up.
3. BUTTON : to return to the previous screen
4. BUTTON : to select and confirm settings
LIST OF FUNCTIONS
Turn the “Functions” knob to any position and the oven switches on: the display shows the functions or the
associated submenus.
The submenus are available and selectable by turning the knob to the functions GRILL, SPECIALS,
SETTINGS, RECIPES and SHORTCUTS.
A. Symbol for highlighted function
B. Highlighted function can be selected by pressing
C. Description of highlighted function
D. Other available and selectable functions.
DETAILS OF FUNCTION
After selection of the desired function, the display will show further options and related details.
To move between the different areas, turn the “Browse” knob: the cursor moves to the adjustable values,
following the order described above. Press button to select the value, change it by turning the “Browse”
knob and confirm with button .
Fig. 1 Fig. 2
1 23 4
Speacials: For defrosting food
Warm Keeping
Frozen Food
Defrosting
DISPLAY
Specials: For defrosting food
Warm Keeping
Frozen Food
Defrost
A
D
C
B
Zone 3 Zone 4
Zone 5
Zone 2
Zone 1Cursor
PREHEAT
Yes
TEMPERATURE
180°C
COOK TIME
END TIME
Convection Bake
--:--
--:--
Start
EN10
USING THE APPLIANCE FOR THE FIRST TIME - LANGUAGE SELECTION AND SETTING
THE TIME
For correct use of the oven, when it is switched on for the first time you will have to select the desired
language and set the correct time.
Proceed as follows:
1. Turn the “Functions” knob to any position: the display will show the list of the first three available
languages.
2. Turn the “Browse” knob to scroll the list.
3. When the desired language is highlighted, press to select it.
After language selection, the display will flash 12:00.
4. Set the time by turning the “Browse” knob.
5. Confirm your setting by pressing .
SELECTING COOKING FUNCTIONS
1. If the oven is off, turn the “Functions” knob; the display will show the cooking functions or associated
submenus.
N.B.:for the list and description of functions, see the specific table at page16 and at page17.
2. Within the submenus, browse the various options available by turning the “Browse” knob: the chosen
function is highlighted in white in the centre of the screen. To select it, press .
3. the cooking settings are displayed on the screen. If the pre-set values are those desired, turn the
“Browse” knob to position the cursor at “Start” and then press ; otherwise, proceed as indicated
above to change them.
SETTING THE TEMPERATURE/OUTPUT OF THE GRILL
To change the temperature or output of the grill, proceed as follows:
1. Check that the cursor is positioned next to the temperature value (zone 3); press button to select
the parameter to be changed: the temperature values flash.
2. Set the desired value by turning the “Browse” knob and press to confirm.
3. Turn the “Browse” knob to position the cursor at “Start” and then press .
4. The display indicates which shelf food should be placed on. Do as instructed and press to start cooking.
The set temperature can also be changed during cooking by following the same procedure.
5. At the end of cooking, the end of cooking message is displayed. At this point the oven can be
switched off by turning the “Functions” knob to 0 (zero), or cooking can be prolonged by turning the
“Browse” knob clockwise. When switched off, the display shows the cooling bar which indicates the
temperature inside the oven.
PREHEATING THE OVEN
If you wish to preheat the oven before inserting food, change the oven’s default selection as follows:
1. Turn the “Browse” knob to position the cursor at preheating.
2. Press button to select the setting: “No” flashes on the display.
3. Change the setting by turning the “Browse” knob: the display shows “Yes”.
4. To confirm your choice, press button .
PREHEAT
Yes
TEMPERATURE
180°C
COOK TIME
END TIME
Convection Bake
--:--
--:--
Start
PREHEAT
Yes
TEMPERATURE
180°C
COOK TIME
END TIME
Convection Bake
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
200°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
200°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
200°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
200°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
Ye s
TEMPERATURE
200°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
Ye s
TEMPERATURE
200°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
EN11
FAST PREHEATING
If you wish to preheat the oven quickly before inserting food, change the oven’s default selection as
follows:
1. Turn the “Functions” knob to the SPECIAL FUNCTIONS symbol, then select “Fast Preheating” using the
“Browse” knob.
2. Confirm by pressing : the settings are displayed on the screen.
3. If the proposed temperature is that desired, turn the “Browse” knob to position the cursor at “Start” and
then press . To change the temperature, proceed as described in previous paragraphs. An acoustic signal
will sound when the oven has reached the set temperature. At the end of preheating, the oven
automatically selects the conventional function .
At this point food can be placed in the oven for cooking.
4. If you wish to set a different cooking function, turn the “Functions” knob and select the desired
function.
SETTING COOKING TIME
This function can be used to cook food for a set length of time, from a minimum of 1 minute to the
maximum time allowed by the selected function, after which the oven switches off automatically.
1. To select the function, turn the “Browse” knob to position the cursor at “COOK TIME”.
2. Press button to select the setting; “00:00” flashes on the display.
3. Change the value by turning the “Browse” knob to display the desired cooking time.
4. Confirm the selected value by pressing button .
BROWNING
At the end of cooking, with certain functions, the display indicates the possibility of browning the surface of
your dish. This function can only be used when cooking time has been set.
At the end of cooking time, the display shows “+/- to prolong, to brown”. Press button , and the oven
starts a 5 minute browning cycle. This function can only be used once after cooking.
TEMPERATURE
180°C
Turn +/- to adjust ...
Start
Specials: For defrosting food
Warm Keeping
Frozen Food
Defrost
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
180°C
HH:MM
END TIME
Conventional
19:01
00:01
Start
PREHEAT
No
TEMPERATURE
180°C
HH:MM
END TIME
Conventional
19:01
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
19:20
- 00:30
Start
Browning
COOK TIME
END TIME
20:05
- 00:05
Cooking nished at 20:00
+/- to prolong, ✓ to brown
Browning nished at 20:05
EN12
SETTING END OF COOKING TIME / DELAYED START
The end of cooking time can be set, delaying the start of cooking by up to a maximum of 23 hours and
59 minutes. This can only be done once cooking time has been set. This setting is only possible when
pre-heating is not required for the selected function.
After setting cooking time, the display shows the end of cooking time (for example 19:20). To delay the end
of cooking time, and thus also the cooking start time, proceed as follows:
1. Turn the “Browse” knob to position the cursor at the end of cooking time.
2. Press button to select the setting: the end of cooking time flashes.
3. To delay the end of cooking time, turn the “Browse” knob to set the desired value.
4. Confirm the selected value by pressing button .
5. Turn the “Browse” knob to position the cursor at START and then press .
6. The display indicates which shelf food should be placed on. Do as instructed and press to start
cooking. The oven will start cooking after a period of time calculated so as to finish cooking at the set
time (for example, in the case of a dish which requires a cooking time of 20 minutes, if the end of
cooking time is set to 20:10, the oven will begin cooking at 19:50).
N.B.:during the interval before cooking starts, the oven can in any case be switched on by turning
the “Browse” knob to position the cursor at “Start” and then pressing .
At any time, set values (temperature, grill setting, cooking time) can be changed as described in
previous paragraphs.
TIMER
This function can be used only with the oven switched off and is useful, for example, for monitoring the
cooking time of pasta. The maximum time which can be set is 1 hour 30 minutes.
1. With the oven switched off, press button : the display will show “00:00:00”.
2. Turn the “Browse” knob to select the desired time.
3. Press button to start the countdown. When the set time has elapsed, the display will show
“00:00:00” and an acoustic signal will sound. At this point the time can be prolonged, proceeding as
described above, or the timer can be deactivated by pressing button (the time of day will be shown
on the display).
RECIPES
Thanks to “Sixth sense” technology, the oven offers 30 pre-set recipes with ideal cooking temperatures.
Simply follow the recipe as regards ingredients and the method of preparation. Then, proceed as follows:
1. Select “RECIPES” by turning the “Functions” knob.
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
19:20
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
19:20
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
20:10
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
20:10
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
20:10
- 00:29
Start
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
20:10
- 00:30
Start
Turn +/- to set Timer, ✓ to Start
00 : 00 : 00
(HH) (MM) (SS)
Turn +/- to set Timer, ✓ to Start
00 : 30 : 00
(HH) (MM) (SS)
Timer
01 : 09 : 00
CONTROL
Automatic
COOK TIME
END TIME
Pork Chops
19:20
- 00:32
Start
Insert food on level 3
Press
✓ when done
6th Sense: Press ✓ to view recipes
Fish
Dessert
Meat
6th Sense: Press ✓ to view recipes
Fish
Dessert
Meat
6th Sense: See cookbook for description
Shank of Pork
Kebabs
Pork Chops
6th Sense: See cookbook for description
Shank of Pork
Kebabs
Pork Chops
EN13
2. Select the dish to be cooked from the proposed list.
3. Confirm the selected dish using button .
4. Select the desired recipe by turning the “Browse” knob.
5. Confirm by pressing : the display shows the approximate cooking time.
6. Place the dish in the oven and turn the “Browse” knob to position the cursor at “Start”, then press .
7. The display indicates which shelf food should be placed on. Do as instructed and press to start
cooking. To delay the start of cooking, see the relevant paragraph.
N.B.:some dishes must be turned or stirred half way through cooking: the oven will emit an acoustic
signal and the display will indicate what action is required.
The initial cooking time displayed is merely for guidance: it can be prolonged automatically during
cooking.
Shortly before cooking time finishes, the oven prompts you to check that the food is cooked to your
satisfaction. If it is not, extra time can then be added manually by turning the “Browse” knob.
MEAT PROBE
The meat probe supplied allows you to measure the exact core temperature of food during cooking,
between 0°and 100°C, in order to ensure that food is cooked to perfection.
Based on the food being cooked, the required core temperature can be set.
It is very important to position the probe accurately in order to obtain perfect cooking results. Insert the
probe fully into the fleshiest part of the meat, avoiding bones and fatty parts (Fig. 1). For poultry, the probe
should be inserted sideways, in the middle of the breast, taking care to ensure the tip does not end up in a
hollow part (Fig. 2).
In the case of meat with very irregular thickness, check it is cooked properly before removing it from the
oven. Connect the end of the probe in the hole located on the right wall of the oven chamber.
Meat probe recipes
1. Select “Meat probe recipes” by turning the functions knob to the corresponding symbol.
2. Select the dish to be cooked from the proposed list and confirm by pressing the button (OK).
N.B.:if you select “custom”, the function allows you to choose all parameters to be set. The other
recipes only allow you to insert some of these.
3. Connect the probe, place the dish in the oven and turn the “Browse” knob to position the cursor at
“Start”, then press .
N.B.:if the probe has not been connected, the display will show a message prompting you to insert it.
If it is not inserted, when you press , the oven will start a traditional cooking cycle without a set time.
If the probe has been connected properly, the display shows a confirmation message for three seconds
followed by a screen indicating all cooking parameters, including the core temperature of the meat as
measured by the probe.
When the required core temperature for the particular food is reached, a message to that effect flashes on
the display for 3 seconds. At the end of cooking time, the oven proposes the option of prolonging cooking
by turning the “Browse” knob to +. This prolongs cooking using the traditional mode without any time
setting. If this option is not selected, the oven waits for 10 minutes before switching off, after which
cooking can no longer be prolonged.
Fig. 1 Fig. 2
Please turn food
Cooking nearly nished
Please check on food
Cooking Finished at 19:45
Press to Prolong Cooking
Automatic roasting functions
Specials
Traditional
Meat Probe Recipes
Automatic roasting functions
Roast Beef
Roast Veal
Custom
Insert Meat Probe
or press OK
EN14
The probe can also be used with the CONVENTIONAL, CONVECTION BAKE, FORCED AIR, TURBO GRILL and
MAXI COOKING functions. If the probe is not inserted, cooking proceeds using the traditional mode,
otherwise, the display advises that the probe is not connected. The message will display for 3 seconds, after
which the oven proceeds as if the “custom” function as indicated above has been selected.
SETTINGS
1. To change some display settings, select “SETTINGS” from the main menu by turning the “Functions”
knob.
2. Confirm by pressing : the display shows which settings can be changed (language, volume of
acoustic signal, display brightness, time, energy saving function).
3. Select the setting to be changed by turning the “Browse” knob.
4. Press button to confirm.
5. Follow the instructions of the display to change the settings.
6. Press button ; a message appears on the display confirming your selection.
N.B.: When the oven is switched off, if the ECOMODE (Energy saving) function is selected (ON), the display
switches off after a few seconds, showing the clock. To view information on the display and switch the light
on again, just press any of the buttons or turn one of the knobs. During a cooking function if the ECOMODE
is activated the cavity lamp will be switched off after 1 minute of cooking and reactivated for each user
interaction. If, on the other hand, the function is not selected (OFF), after a few minutes the display is merely
dimmed.
KEY-LOCK
This function can be used to lock the buttons and knobs on the control panel.
To activate it, press and at the same time for at least 3 seconds. If activated, the functions of the
buttons are locked and the display shows a message and the symbol . This function can also be activated
during cooking. To deactivate it, repeat the above procedure. When the key-lock function is activated, the
oven can be switched off by turning the knob to 0 (zero). In this case, however, the previously selected
function will have to be set again.
AUTOMATIC OVEN CLEANING
For the description of this function, see the chapter CLEANING and the functions table at page16.
To activate the oven’s automatic cleaning cycle (pyro-cleaning), proceed as follows:
1. Use the “Functions” knob to select “Cleaning”. The display shows “Pyro Express” and “Pyro”.
2. Select one of the two cycles using the “Browse” knob. Confirm by pressing :
3. Turn the “Browse” knob to position the cursor at START, then confirm by pressing button .
4. the display shows the instructions to be followed in order to start the cycle. After following each
instruction, confirm with button .
5. Upon the final confirmation, the oven starts the cleaning cycle and the door is automatically locked:
a warning and the symbol are shown on the display for around three seconds. Immediately
afterwards, the display shows a progress bar indicating the cleaning cycle progress.
Meat Probe
has been connected
TEMPERATURE
150°C
MEAT PROBE
Cooking
100°C
CURRENT
79°C
TEMPERATURE
150°C
MEAT PROBE
Temperature reached
100°C
CURRENT
100°C
Insert Meat Probe
or press OK
PREHEAT
No
TEMPERATURE
180°C
COOK TIME
END TIME
Conventional
--:--
--:--
TEMPERATURE
150°C
MEAT PROBE
Conventional
100°C
TIME
Cleaning
- 03:00
END TIME
15:00
3 hours high temperature cleaning
Pyro Express
Pyro
1/3
Please switch o cooktop
above oven and press
✓
2/3
Please remove all accessories
from the oven and press
✓
3/3
Remove stains from glass
with moist sponge and press
✓
Door will be locked
during cleaning
TIME
Cleaning
- 02:59
END TIME
15:00
Please close door
EN15
N.B.:If the oven door is opened before it is unlocked automatically, a warning message appears
on the display. When the door is reclosed, the cycle must be started again by pressing button .
6. At the end of the cycle, the relative message flashes on the display, after which the cooling bar
indicates cooling in progress. The residual temperature is indicated on the display together with the
symbol . The door remains locked until the temperature inside the oven has returned to an
acceptably safe level: the display shows the time of day.
TIME
Finished
- 00:00
END TIME
15:00
Cooling Down
257°
18:32
EN16
FUNCTION DESCRIPTION TABLE
FUNCTION KNOB
OFF To halt cooking and switch off the oven.
CONVENTIONAL
To cook any kind of dish on one shelf only. Use the 3rd shelf. To cook pizza,
savoury pies and sweets with liquid fillings, use the 1st or 2nd shelf. The oven
does not have to be preheated.
GRILL
To grill steak, kebabs and sausages; to cook vegetables au gratin and toast
bread. Place food on the 4th or 5th shelf. When grilling meat, use the drip tray
to collect the cooking juices. Position it on the 3rd/4th shelf, adding approx.
half a litre of water. The oven does not have to be preheated. During cooking
the oven door must remain closed.
TURBO GRILL
To roast large joints of meat (legs, roast beef, chickens). Position the food on
the middle shelves. Use the drip tray to collect the cooking juices. Position it
on the 1st/2nd shelf, adding approx. half a litre of water. The oven does not
have to be preheated. During cooking the oven door must remain closed.
With this function you can also use the turnspit, if provided.
FORCED AIR
To cook a variety of food requiring the same cooking temperature on several
shelves (maximum three) at the same time (e.g. fish, vegetables, cakes). This
function can be used to cook different foods without odours being
transferred from one food to another. Use the 2nd shelf to cook on one shelf
only, the 1st and 4th to cook on two shelves, and the 1st, 3rd and 5th to cook
on three shelves. The oven does not have to be preheated.
AUTOMATIC
OVEN CLEANING
To burn off spatters produced during cooking with an extremely high
temperature cycle (approx. 500°). Two auto-cleaning cycles are available: a
shorter cycle (Pyro Express) and a complete cycle (Pyro). The complete cycle
is best used only in the case of very dirty ovens, while the shorter cycle
should be used at regular intervals.
CONVECTION
BAKE
To cook meat and pies with liquid filling (savoury or sweet) on a single shelf.
Use the 3rd shelf. The oven does not have to be preheated.
SPECIALS See SPECIAL FUNCTIONS.
SETTINGS
Setting the display (language, time, brightness, volume of acoustic signal,
energy saving function).
RECIPES
Selecting 30 different pre-set recipes (see enclosed recipe booklet). The oven
automatically sets the optimum cooking temperature, function and time. It is
important to follow the instructions given in the recipe book regarding
preparation, accessories and which oven shelf to use.
MEAT PROBE
RECIPES
To select 7 optimal cooking modes for different types of meat. The oven
automatically sets the final core temperature of the meat selected and the
ideal oven temperature for cooking. These values are given in the specific
cooking table provided, however they can be changed manually within a
pre-set range. For correct insertion and use of the probe, follow the
instruction given in the relative paragraph. Position the meat on the 3rd shelf,
using an oven tray placed on the wire shelf or the drip tray alone. The oven
does not have to be preheated. During cooking, the oven door can be
opened to check the meat or add stock, but take care not to move the probe.
SHORTCUTS
To directly access the 10 most used functions. To change the settings of the
desired function, see paragraph “SELECTING COOKING FUNCTIONS”.
EN17
SPECIAL
DEFROST
To speed up defrosting of food. Place food on the middle shelf. Leave food in
its packaging in order to prevent it from drying out on the outside.
KEEP WARM
For keeping just-cooked food hot and crisp (e.g: meat, fried food or flans).
Place food on the middle shelf. The function will not activate if the
temperature in the oven is above 65°C.
RISING
For optimal rising of sweet or savoury dough. To safeguard the quality of
proving, the function will not activate if the temperature in the oven is above
40°C. Place the dough on the 2nd shelf. The oven does not have to be
preheated.
CONVENIENCE
Cooking ready meals kept at room temperature or from refrigerated cabinets
(biscuits, liquid cake mixtures, muffins, first courses and bakery products).
This function gently cooks all food quickly; it can also be used to reheat
cooked food. Follow the instructions on the food packaging. The oven does
not have to be preheated.
MAXI COOKING
To cook large joints of meat (above 2.5 kg). Use the 1st or 2rd shelves,
depending on the size of the joint. The oven does not have to be preheated. It
is advisable to turn the meat over during cooking, to obtain even browning
on both sides. It is preferable to baste the meat every now and again so that it
does not become too dry.
FROZEN
FOOD
Lasagne
The function automatically selects the ideal cooking temperature and mode
for 5 different types of ready frozen food. Use the 2nd or 3rd shelf. The oven
does not have to be preheated.
Pizza
Strudel
French
Fries
Bread
Custom The temperature can be set from 50 to 250°C to cook other types of product.
FAST PREHEATING
To preheat the oven rapidly. For use, refer to the specific paragraph on
previous pages.
ECO FORCED AIR
To cook stuffed roasts and meat in pieces on one shelf. This function uses
discontinuous, delicate fan assistance, which prevents excessive drying of
foods. In this ECO function the light remains off during cooking and can be
temporarily switched on again by pressing the confirm button. In order to
maximize energy efficiency, it is advisable not to open the door during
cooking. It is advisable to use 3rd level. The oven does not have to be
preheated.
EN18
COOKING TABLE
Recipe Function Pre-
heating
Shelf (from
bottom)
Temp.
(°C)
Time
(min)
Accessories and notes
Leavened cakes
- 2/3 160-180 30-90 Cake tin on rack
- 1-4 160-180 30-90
Level 4: cake tin on rack
Level 1: cake tin on rack
Filled pies
(cheesecake, stru-
del, apple pie)
- 3 160-200 35-90
Drip-tray / baking tray or cake
tin on rack
- 1-4 160-200 40-90
Level 4: cake tin on rack
Level 1: cake tin on rack
Biscuits/Tartlets
- 3 170-180 20-45 Drip-tray or baking tray
- 1-4 160-170 20-45
Level 4: rack
Level 1: drip-tray or baking
tray
- 1-3-5 160-170 20-45*
Level 5: pan on rack
Level 3: pan on rack
Level 1: drip-tray or baking
tray
Choux buns
- 3 180-200 30-40 Drip-tray or baking tray
- 1-4 180-190 35-45
Level 4: pan on rack
Level 1: drip-tray or baking
tray
- 1-3-5 180-190 35-45*
Level 5: pan on rack
Level 3: pan on rack
Level 1: drip-tray or baking
tray
Meringues
- 3 90 110-150 Drip-tray or baking tray
- 1-4 90 140-160
Level 4: pan on rack
Level 1: drip-tray or baking
tray
- 1-3-5 90
140-
160*
Level 5: pan on rack
Level 3: pan on rack
Level 1: drip-tray or baking
tray
Bread / Pizza /
Focaccia
-1/2190-250 15-50 Drip-tray or baking tray
- 1-4 190-250 20-50
Level 4: pan on rack
Level 1: drip-tray or baking
tray
- 1-3-5 190-250 25-50*
Level 5: pan on rack
Level 3: pan on rack
Level 1: drip-tray or baking
tray
Leht laaditakse ...
Leht laaditakse ...
Leht laaditakse ...
Leht laaditakse ...
Leht laaditakse ...
Leht laaditakse ...
Leht laaditakse ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
teistes keeltes
- English: Whirlpool AKZM 7820/WH User guide
Seotud paberid
-
Whirlpool AKZM 6600/IX Kasutusjuhend
-
-
-
-
-
-
Whirlpool AKZM 656/IX Kasutusjuhend
-
Whirlpool AKZM 6560/IX Kasutusjuhend
-
Muud dokumendid
-
Tefal GC740B30 Kasutusjuhend
-
-
Vestfrost VBO 1460 PN Built-In Oven Kasutusjuhend
-
Candy FMBC A825S E0 Kasutusjuhend
-
-
Sage SGR840 Kasutusjuhend
-
-
Bosch HSV482ASC/04 Kasutusjuhend
-
Teka JZC 63312 ABN Kasutusjuhend
-
Husqvarna 115iHD55 Kasutusjuhend