Purmo Kaba2 paigaldusjuhend

KABA2

INSTALLATION

AND OPERATING

MANUAL

A NEW GENERATION THAT TURNS EVOLUTION INTO A REVOLUTION CLASS I – 230V & 400V – 50 HZ

INSTALLATION

OCH

BRUKSANVISNING

EN NY GENERATION SOM FÖRVANDLAR EVOLUTIONEN TILL EN REVOLUTION KLASS I - 230V & 400V - 50 HZ

INSTALLASJON

OG

BRUKSANVISNING

EN NY GENERASJON SOM GJØR EVOLUSJON TIL EN REVOLUSJON SKLASSE I – 230V & 400V – 50 HZ

INSTALLATIONS-

OG

BETJENINGSVEJLEDNING

EN NY GENERATION, DER GÅR EVOLUTION TIL EN REVOLUTION KLASSE I – 230V & 400V – 50 HZ

ASENNUS-

JA

K

Ä

YTT

Ö

OHJE

UUSI SUKUPOLVI, JOKA MUUTTAA EVOLUUTIOSTA VALLANKKUUKSEN CLASS I – 230V – 50 HZ

GB

1

2

A

H

(mm)

A

(mm)

B

(mm)

C

(mm)

300

100 - 150

46

173

500

100 - 150

46

373

PRODUCT

INFORMATION

2

2B

2C

PRODUCT

INFORMATION

3

NO

PRODUCT

INFORMATION

4

SAFETY

INFORMATION

Due to the safety standard EN 60335,

the text below is obligatory for all electric

products, not only radiators.

This appliance can be used by children

aged from 8 years and above and persons

with reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given

supervision or instruction concerning

use of the appliance in a safe way and

understand the hazards involved. Children

shall not play with the appliance. Cleaning

and user maintenance shall not be made

by children unless they are older than 8

and supervised. Keep the appliance and

its cord out of reach of children aged less

than 8 years. Children of less than 3 years

should be kept away from the unit unless

continuously supervised. Children aged

from 3 years and less than 8 years shall

only switch on/off the appliance provided

that it has been placed or installed in its

normal operating position and they have

been given supervision or instruction

concerning use of the appliance in a safe

way and understand the hazards involved.

Children aged from 3 years and less than 8

years shall not plug in, regulate and clean

the appliance or perform user maintenance.

CAUTION

THIS PRODUCT MUST NOT BE INSTALLED IN A BATHROOM OR OTHER

SIMILAR HIGH HUMIDITY AREA.

CAUTION

SOME PARTS OF THIS PRODUCT CAN BECOME VERY HOT AND CAUSE BURNS.

PARTICULAR ATTENTION HAS TO BE GIVEN WHERE CHILDREN AND VULNERABLE

PEOPLE ARE PRESENT. IN ORDER TO AVOID OVERHEATING, DO NOT COVER THE

RADIATOR. ”DO NOT COVER” MEANS THAT THE RADIATOR MUST NOT BE USED

FOR DRYING CLOTHES, FOR EXAMPLE, BY PLACING THEM DIRECTLY ON THE

RADIATOR.

WASTE DISPOSAL ACCORDING TO WEEE DIRECTIVE

(2012/19/EU)

WASTE DISPOSAL ACCORDING TO THE WEEE DIRECTIVE (2012/19/EU). THE SYMBOL

ON THE PRODUCT LABEL INDICATES THAT THE PRODUCT MAY NOT BE HANDLED AS

DOMESTIC WASTE, BUT MUST BE SORTED SEPARATELY. WHEN IT REACHES THE END OF

ITS USEFUL LIFE, IT SHALL BE RETURNED TO A COLLECTION FACILITY FOR ELECTRICAL

AND ELECTRONIC PRODUCTS. BY RETURNING THE PRODUCT, YOU WILL HELP TO

PREVENT POSSIBLE NEGATIVE EFFECTS ON THE ENVIRONMENT AND HEALTH TO

WHICH THE PRODUCT CAN CONTRIBUTE IF IT IS DISPOSED OF AS ORDINARY DOMESTIC

WASTE. FOR INFORMATION ABOUT RECYCLING AND COLLECTION FACILITIES, YOU

SHOULD CONTACT YOUR LOCAL AUTHORITY/MUNICIPALITY OR REFUSE COLLECTION

SERVICE OR THE BUSINESS FROM WHICH YOU PURCHASED THE PRODUCT. APPLICABLE

TO COUNTRIES WHERE THIS DIRECTIVE HAS BEEN ADOPTED.

GB

5

GB

SAFETY

INFORMATION

1.

GENERAL

INFORMATION

•

This appliance is a sealed electric radiator.

•

This appliance conforms to the standards EN 60335-1

and EN 60335-2-30.

•

This appliance is insulation class I and has electrical

protection level IP21.

•

This appliance complies with the European Directive

2014/30/EU (CE Marking on all appliances).

•

KABA2:

-

for wall mounting or freestanding positioning.

-

230 V – 50 Hz supply.

-

Supplied with 3 core cable and fitted with an earthed

plug, wall brackets and screws.

-

or 400 V – 50 Hz supply.

-

for wall mounting only.

-

Supplied with 3 core cable, wall brackets and screws.

2.

INSTALLATION

POSITIONING

•

The radiator must be positioned horizontally in order for

it to function correctly.

•

The radiator must be positioned according to the

applicable standards. The minimum distances as

specified in picture 1 should be carefully observed.

•

The radiator must be fixed to the wall using the wall

brackets supplied.

•

The radiator must not be located underneath an electrical

socket.

FIXING

•

Mark out the distance between the brackets and the

positions of the screw holes as shown in the table in

picture

2A

.

•

Note that the brackets can be used to measure the height of

the bottom fixing hole, see picture

2B

.

•

For

the correct installation of

radiators it is essential

that

the

fixing of the radiator is carried out in such a way that

it is suitable for intended use AND predictable misuse.

A number of elements need to be taken into consideration

including the fixing method used to secure the radiator

to the wall, the type and condition of the wall itself, and any

additional potential forces, or weights, prior to finalizing

installation.

•

The fixing materials provided are only intended for

installation on walls made of solid wood, bricks, concrete or

on timber-frame stud walls where the fixing is directly into

the timber. All walls being considered should have no more

than a maximum of 3 mm wall finishing. For walls made of

other materials, for example hollow bricks; please consult

your installer and/or specialist supplier.

In all cases it is strongly recommended that a suitably

qualified professional installer or similar tradesperson

carries out the installation.

CONNECTION

•

The electrical installation must comply with local or

national regulations.

•

The radiator must be connected to the electrical supply

using the supply cable fitted to the unit.

•

The radiator is equipped with a non-resettable overheat

protection that trips off if the radiator overheats. If the

radiator is removed from the wall brackets, even for a

short time, it must without exception be switched off, see

picture

3

. This may even trip the non-resettable overheat

protection. If the overheat protection trips, its thermal fuse

must be replaced; contact your supplier.

6

GB GENERAL

INFORMATION

OVERVIEW

Electronic PlD control unit for electric radiator, programmable

digital control, white color.

PRODUCT PLUS POINTS

OPERATION

DIAGRAM

• Buttons

overview

Selecting operating modes

Plus and minus buttons, used to set temperatures, time, date and

programs

Save

settings



Indicator overview



Electronic PID control with microprocessor.



Setting temperature can be viewed in all operating modes.



Double

pole

ON/OFF

switch.



Gauge consumption:

Automatic indication of the level of

consumption

according to the setting temperature.

Energy consumption indication: posting of the

estimated

amount of energy consumed in kWh since the

last reset to 0 of

the energy meter.



Open window detection:

Automatic switching to frost

protection mode when the device detect a significant

drop in tem

perature.

7 day program: you have the option, for each day of

the week, of assigning five different program profiles.

Child anti-tamper: The control panel can be locked,

making changes impossible.



Special safety for social or private rental housing:

o

Limits of the adjustment range of the Comfort

setting tem

perature.

o

PIN code lock of settings reserved for

professionals.



Active

memory:

Permanent

backup

of

the

whole

of

settings

and programming, backup date and time of

3h.

Gauge

consumption

Heating

indicator

Days of the week (1=Monday … 7= Sunday)

Setting

temperature

Open window detection indicator

Keypad

locked

Operation

modes:

Auto

mode

Comfort

mode

Eco

mode

Frost protection mode

Time and date setting mode

Programming mode

Settings

Note

Before carrying out any setting procedures, ensure that

the keypad is indeed unlocked (see page 10).

7

• Auto

mode

In Automatic Mode, the device will

automatically change from

Comfort

mode to Eco mode according to

the

established program.

3

• Frost protection mode

This mode enables you to protect

your home against the effects of

cold

weather

(frozen

pipes,

etc.),

by

maintaining a minimum temperature of

7°C in it at all times. Select this mode

when you will be away from your home

for a

long time (more than 5 days).

GAUGE CONSUMPTION, ENERGY

SAVINGS

SETTING THE COMFORT MODE

TEMPERATURE

POWER

ON

Mode

overview Display

Restoring factory settings

See pages 15, 17 and 20.

SELECTING THE OPERATING MODE

The button allows you to adapt the

operating

schedule of your device to your

needs, depend

ing on the season, whether your

home is occu

pied or not.

Press the button several times to select the

required mode.

Mode

sequence:

R

ecommended Comfort setting temperature should be lower

or

equal to 19°C.

In

the

device

display,

a

selector

indicates

the

energy

comsump-

tion level by positioning it in front of the color: red, orange or

green. So, depending on the setting temperature, you can

choose your level of energy usage. As the temperature setting

increases, the consumption will be higher.

The gauge appears in Auto, Comfort, Eco and Frost protection

modes and whatever the temperature level.

Mode

overview Display

2

different

cases

depending

on

your

set-up

:

A. 7 day and daily program

Your

device

has

been

programmed

and

is

executing

Comfort

and

Eco

mode orders in line with the settings and time periods you have selected

(see "7 day and daily program integrated" chapter page 10).

B. Without program

if the 7 day and daily program is not enabled, then your device’s

factory settings mean that it will operate in nonstop Comfort mode, 7

days of the week.

You can access the Comfort temperature set up from the Auto

and Comfort Mode. It is preset to 19°C.

Using

and

you can adjust the temperature from 7°C to

30°C by intervals of 0.5° C.

Note: you can limit the Comfort temperature, see page 14

for more details.

Auto

Comfort

Eco

Frost Protection

Power on switch

Set the switch in ON position in order

to power up the appliance.

3

• Comfort

mode

Non-stop Comfort mode. The device

will operate 24 hours a day to achieve

the temperature which has been set

(e.g. 19°C). The Comfort mode

temperature level can be set by the

user

(see Setting the comfort mode

temperature page 9).

• Eco

mode

Eco,

which

means

the

Comfort

Mode

temperature minus 3.5°C. This enables

you to lower the temperature

without

having to reset the Comfort Mode

tem

perature.

Select

this

mode

for

short term

absenc

es (between 2 and

24h) and during

the

night.

C - Red color

High Temperature

level: it is advisa

ble

to significantly

reduce the setting

temperature.

Setting

temp.

> 22°C

When the setting

temperature is

higher than 22°C

B -

Orange

color

Average

tempe

rature level: it

is

advisable

to slightly reduce

the setting

temper

ature.

19°C < Setting

Temp.

≤ 22°C

When the setting

temperature is

higher than 19°C

and lower or equal

to

22°C.

A - Green color

Setting temp. ≤ 19°C

When the setting

Ideal temperature. temperature is

lower or equal to

19°C

8

1-

From Auto, Comfort, Eco or Frost protection mode, press

for 5 seconds.

The cursor moves to the setting day and time mode.

It is possible to see the estimation of energy consumption in kWh

since the last reset of the energy meter.

Display of the estimated power consumption

To see this estimation, from Auto,

Comfort, Eco or Frost protection

mode, then press .

To exit the display mode of

consumption: press

or , the device is automatically in

the previous active mode.

2-

Select

using

or . The two hour figures will flash.

Resetting the energy meter

To reset the energy meter, from Auto, Comfort, Eco or Frost pro-

tection mode, then proceed as follows.

1-

Press

.

2-

Press

simultaneously

and

for more

than 5 seconds.

To exit resetting the energy meter, press or , the

de- vice is automatically in the previous active mode.

The hours will scroll quickly, if you press the or

and hold

them.

Save by pressing .

Keypad lock

To lock the keypad, press the

and buttons and hold

them down for 10 seconds. The

padlock symbol appears

on the display, the keypad is

locked.

3-

The two minute figures will flash.

Select

using or .

Save by pressing

.

Keypad

unlock

To unlock the keypad, press the and buttons and

hold

them down for 10 seconds again. The padlock symbol

disappears from the display, keypad is unlocked.

4-

The courser above the number 1 (which represents the

Monday) will flash. Select the day using or .

Seve by pressing .

1

In this mode, you have the option of programming your device,

by setting one of the five programmes on offer for each day of

the week.

Access to the programming mode

From Auto, Comfort, Eco or Frost protection mode, press

for

5 seconds to enter into the programming mode.

Schematic sequence of programming settings:

5-

To

change

and/or

allocate

programs

press

. To exit the

Setting day and time

In this mode, you can set day and time to program your device

in line with your needs.

setting the time and day mode, press

3 times.

1 2 3 4 5 6 7

3

Setting

time

Setting

day

Programmes

choice

1

5 sec.

7 DAY AND DAILY PROGRAM

INTEGRATED, ENERGY SAVINGS

CHILD ANTI-TAMPER,

KEYPAD LOCK/UNLOCK

CONSUMPTION INDICATION

ACCUMULATED IN KWH, ENERGY

SAVINGS

9

Choices

programmes

Schematic sequence of programmes:

Your

device’s

default

setting

is

non-stop

Comfort

for

7 days a

week.

3-

With

or , select P1.

P1 will flash. Press

for 5 seconds to make changes.

Programmes overview

-

Comfort:

your device will operate in Comfort mode, 24 hours a

day, as regards each day selected.

Note:

You can set the Comfort mode temperature to the tem-

perature you require (see Setting the comfort mode tempera-

ture page 9).

-

Eco: The device will operate 24 hours a day in Eco mode.

Note:

You can set the temperature-lowering parameters (see

Setting the Eco mode temperature lowering-level page 14).

-

P1: your device will operate in Comfort mode from 06:00 to

22:00 (and in Eco mode from 22:00 to 06:00).

-

P2: your device will operate in Comfort mode from 06:00 to

09:00 and from 16:00 to 22:00 (and in Eco mode from 09:00 to

16:00 and from 22:00 to 06:00).

-

P3: your device will operate in Comfort mode from 06:00 to

08:00, from 12:00 to 14:00 and from 18:00 to 23:00 (and in Eco

mode

from

23:00

to

06:00,

from

08:00

to

12:00

and

from

14:00

to 18:00).

Potential modifications of programmes

If the default time schedules for the P1, P2 and P3 programmes

does not suit your routines, you can change them.

Modifying the P1, P2 or P3 programmes.

If you modify the time schedules for the P1, P2 or P3 programmes,

the schedules will be modified for all the days of the week for

which P1, P2 or P3 had been set.

1-

If you just set the time and day, go to step 2.

From Auto, Comfort, Eco or Frost protection mode, press

for 5 seconds.

When the cursor moves above the setting time symbol ,

press shortly.

4-

The P1 start time (which by default is 06:00) will flash.

Using

or , you can change this time, by increments of

30 minutes.

Save by pressing .

5-

The P1 end time (which by default is 22:00) will flash. Using

or

, you can change this time, by increments of 30

minutes.

Save by pressing

.

2-

Press or

. The cursor moves above

prog

.

6-

Press to exit the programming Mode and return to Auto

Mode.

Note:

without action on the keys, it will return to Auto after a few

minutes.

Choices and allocation programs

1-

If you just set the time and day, the cursor moves automati-

cally under PROG.

From Auto, Comfort, Eco or Frost protection mode, then press

for 5 seconds. When the cursor positioned under the set

time symbol , press

again.

Prior

information:

display

area

Correspondence days /

numbers

Monday

1

Tuesday

2

Wednesday

3

Thursday

4

Friday

5

Saturday

6

Sunday

7

2

Comfort

Eco

P1

P2

P3

10

The days of the week will scroll on display with the programmes

that you set for them, meaning Comfort

every day.

Manual and temporary exemption from a running

program

This function allows you to change the Eco mode temperature

temporarily until the next scheduled change in temperature or

the transition to 0:00.

Example:

1-

The device is in Auto mode, the running programme is Eco

15,5°C.

2-

Press or .

The programme set for day 1 (1= Monday, 2 = Tuesday, etc.)

will flash.

2-

By pressing

or , you can change temporarily the de-

sired temperature up to 18°C for example.

3-

Chose the program you want for this day with

or .

Save by pressing

.

1 2

4-

The programme assigned to the second day of the week

(Tuesday) will flash.

Repeat the procedure described previously (in point 3) for

each day of the week.

Note:

The cursor corresponding to the operating mode, i.e Eco

mode in our example, is blinking during the duration of the tem-

porary

derogation.

3-

This change will be automatically cancelled at the next

change of program or transition to 0:00.

5-

Once you have chosen a programme for each day, confirm

your selection by pressing

.

The

days

of

the

week

will

suc-

cessively scroll on display with the programmes that you set

for them (P1, P2, P3, CONF or ECO).

To exit the Programming mode, press

twice.

Viewing the programs that you have selected

-

From

Auto,

Comfort,

Eco

or

Frost

protection

mode,

press

for 5 seconds. Press twice, the programme for each

day

of the week (Comfort, Eco, P1, P2 or P3) will scroll on

display in

front of you.

-

To exit the programme viewing mode, press twice.

Important information about the open window

detection

Important: the open window detection is sensitive to temper-

ature

variations.

The

device

will

react

to

the

window

openings

in accordance with different parameters: temperature setting,

rise and fall of temperature in the room, outside temperature,

location of the device...

If the device is located close to a front door, the detection

may be disturbed by the air caused by opening door. If this is a

problem,

we

recommend

that

you

disable

the

automatic

mode

open window detection (see page 16). You can, however, use

the manual activation (see page 13).

OPEN WINDOW DETECTION, ENERGY

SAVINGS

1

3

11

Overview

Lowering temperature cycle by setting frost protection dur-

ing

ventilation

of

a

room

by

opened

window.

You

can

access

the open window detection from the Comfort, Eco and Auto

modes. Two ways to enable the detector:

-

Automatic activation,

the lowering temperature cycle starts as

soon as the device detects a temperature change.

-

Manual activation,

the cycle of lowering temperature starts by

pressing a button.

Automatic activation (factory settings)

To disable this mode, see page 16.

The device detects a temperature fall. An opened window, a

door to the outside, can cause this temperature fall.

Note: The difference between the air from the inside and the

outside must cause a significant temperature fall

to be percep-

tible by the device.

This

temperature

drop

detection

triggers

the

change

to

Frost

Protection mode.

Manual

activation

By pressing for

more than 5 seconds,

the device will switch

on Frost protection

mode.

Principe

In Comfort, Eco and Frost protection modes,

only orders of the

open window sensor will be considered.

In Auto mode,

the device can receive different orders coming

from :

-

7 day and daily programming integrated (Comfort or Eco

orders);

-

Open window detector.

In general, it is the lowest received order which prevails.

If an open window is detecting, switching to frost protection takes

precedence

•

Example

7 day and daily programming

= Eco

Open window detector

= Frost protection

Frost

protection

Frost protection digital meter

When the device performs a lower temperature cycle due to

opened window, a meter appears on the display to show the

cycle time. The counter is automatically reset at the next

time to Frost protection by opened window (automatic or

manual activation).

Stop the Frost protection mode

By pressing one button, you stop the Frost protection mode.

Note: if a temperature rise is detected, the device may return

to

the previous mode (active mode before the open window

detection).

INFORMATION ABOUT PRIORITIES BE-

TWEEN THE DIFFERENT MODES

Legend

= the favored

location

= another location

12

1

Information

display

2

Information

display

User

= User settings

3

Press for 5

seconds

Press briefly

twice

Press briefly

1

SETTING THE ECO MODE TEMPERATURE

LOWERING-LEVEL

SETTING THE FROST PROTECTION

TEMPERATURE

COMFORT SETPOINT TEMPERATURE

LIMIT

USER

SETTINGS

ACCESS

You access to user settings in 3 steps:

From Auto, Comfort, Eco or Frost protection mode :

Setting

sequence:

Eco

mode

temperature

lowering-level

Frost

protection

temperature

Comfort

setting

temperature

limit

Temperature

unit

The drop in temperature is set at -3.5°C compared to the set

temperature of the Comfort mode. You can adjust the lowered

level from -1°C to -8°C, by intervals of 0.5°C.

Important: whatever the lowering level set, the Eco setting tem-

-

perature will never exceed 19°C.

1-

Press or

to obtain the temperature level you require.

2-

Press to save and move to the next setting.

To exit the user settings, press

twice.

Your device is preset at 7°C. You can adjust the Frost protection

temperature from 5°C to 15°C, by intervals of 0.5°C.

3-

Press or to obtain the temperature you require.

4-

Press

to save and move to the next setting.

To exit the user settings, press

twice.

You can limit the setting temperature range by introducing a

maximum and / or minimum setting, preventing unintentional

changes in temperature.

•

Low temperature limit

Locking of the setting range using a minimum temperature stop,

preventing

the

temperature

from

being

set

below

that

temper-

ature.

The minimum setting is preset to 7°C. You can adjust from 7°C to

15°C by intervals of 1°C.

5-

To change the minimum temperature setting, press or

then save by pressing .

1 2

13

5

sec.

If you do not want to change it, press : the device

chang

es automatically to set the maximum setting. To exit

the user

settings, press twice.

•

High temperature limit

Locking of the setting range using a maximum temperature in-

crease, preventing the temperature from being set above that

temperature.

The maximum setting is preset to 30°C. You can adjust from 19°C

to 30°C by intervals of 1°C.

6-

To change the maximum temperature setting, press

or

.

To save and move automatically to the next setting, press

. To exit the user settings, press

twice.

SETTING THE TEMPERATURE UNIT

The pre-set temperature unit is degrees Celsius. This setting can-

not be changed on this version.

=

Factory settings reset

=

Factory settings not reset

3-

Press the key

for 5 seconds. The device returns to its initial

configuration and

goes

back

automatically

to

the

home

dis-

play of the user settings.

The following factory values will be effective:

Operating

User settings

7-

To move automatically to the next setting, press .

To exit the user settings, press twice.

RESTORING FACTORY SETTINGS

In order to a coming back to factory settings, proceed in the

following order:

1-

From the setting of the temperature unit, press .

appears on the display

.

Press

to exit the

user

settings.

2-

appears.

Press

or to select .

Parameters

Factory

settings

Comfort setting

temperature

19°C

Keypad

lock Disabled

Eco mode temperature

lowering-level

-

3,5°C

Frost protection temperature

7°C

Minimum set of Comfort

setting temperature 7°C

Maximum set of Comfort

setting temperature 30°C

Temperature

unit °C

14

1

Information

display

2

Information

displays

3

InSt = Installer settings

4

Press for 5

seconds

1

Press briefly

twice

1

Press

for

10

seconds

Press briefly

INSTALLER SETTINGS

ACCESS

You access to installer settings in 4 steps:

From Auto, Comfort, Eco or Frost protection mode :

Setting

sequence:

Open window detection

PIN code lock

Restoring factory settings

-

Minimum and maximum Limits of the setting temperature

range (the Comfort temperature modification is forbidden out

of the authorised setting range).

- Programming

mode.

- Open window detection settings.

- Setting the Eco mode temperature lowering-level.

The automatic mode enabled is the default setting.

1-

Press or .

=

automatic mode enabled.

=

automatic mode disabled.

2-

To save and move automatically to the next setting, press

. To exit the user settings, press

3 times.

PIN CODE LOCK

Overview

Your heating device is protected by a safety code against

nonauthorized use. The PIN code (Personal Identity Number) is a

customisable 4 numbers code. When enabled, it prevents

access to the following settings:

-

Selecting the Comfort mode : The access to the Comfort mode

is forbidden, only the Auto, Eco and Frost protection modes

are available.

- Setting the Frost protection temperature.

3 important steps are needed for the first use of the PIN code

lock:

1 - PIN code initialisation, enter the pre-set PIN code (0000)

to

access to the feature.

2 - Activation of the PIN Code to lock settings which will be

protected by the PIN code.

3 - Customizing the PIN code, replace 0000 by the customized

code.

PIN code initialisation

By default, the PIN code is not enabled. appears on the

display.

1-

By default registered PIN code is 0000.

Press or

to select 0. It is blinking. Save by pressing .

1 2

2-

For others numbers, select 0 by press .

When 0000 appears, press on

again to save and exit.

OPEN WINDOW DETECTION,

ACTIVATION/ DEACTIVATION OF THE

AUTO MODE

15

The PIN code is initialized, the next setting automatically appears:

PIN Code activation.

Activation/deactivation of the PIN Code

1-

appears

on

the

display.

Press

or

to enable

code.

appears

on

the

display.

=

PIN code enabled

=

PIN code disabled

3-

Press

to confirm. The new code is now saved.

4-

Press again on to exit setting PIN code mode and go

back to the home display of the installer settings.

2-

Press to save and return to the home installer settings

display.

The PIN code is enabled. Any modification of reserved settings

listed in "Overview" is now impossible.

Customizing the PIN code

If you have just activated the PIN code, follow the stages de-

scribed below.

Alternatively, you must copy the steps 1 and 2 of the initialization

process as well as the steps 1 and 2 of the activation process

before personalizing the PIN code.

Please remember that the personalization of the PIN code can

only be set once the initialization and activation of the PIN code

has been completed.

1-

When appears, press

for at least 5 seconds.

To exit the Installer settings, press

twice.

RESTORING FACTORY SETTINGS

If the PIN code protection is disabled, the user and installer settings

are re-initialized:

1-

From the PIN code setting, press . appears

briefly on the display.

2-

appears.

Press

or to select .

2-

The

0000

code

appears

and

the

first

number

blinks.

Press

or

to select the first desired number then press

to

save

and exit. Repeat this operation

for remaining

3 numbers.

=

Factory settings reset

=

Factory settings not reset

16

5

sec.

1

Information

display

2

Information

displays

3

Press for 5

seconds

1

Press briefly

twice

1

Press

for

10

seconds

Information

display

4

Pro

=

Expert

settings

5

Long

and

simultaneous

10

seconds press

Press briefly

3-

Press the key for 5 seconds. The device returns to its initial

configuration and goes back automatically to the home dis-

play of the installer settings.

The following factory values will be effective:

Operating

User settings

Installer

settings

To exit the installer settings, press

twice.

EXPERT

SETTINGS

ACCESS

You access to expert settings in 5 steps.

From Auto, Comfort, Eco or Frost protection mode :

Setting

sequence:

Ambient temperature sensor adjustment

Setting the power

Restoring factory settings

AMBIENT TEMPERATURE SENSOR ADJUSTEMENT

Overview

Important:

This

operation

is

reserved

for

professional

installers

only; any wrong changes would result in control anomalies.

In which case if the temperature measured (measured by relia-

ble

thermometer)

is

different

by

at

least

1°C

or

2°C

compared

to

the setting temperature of the radiator.

The calibration adjusts the temperature measured by the am-

bient temperature sensor to compensate for a deviation from +

5°C to - 5°C by intervals of 0.1°C.

Ambient

temperature

sensor

adjustment

1-

If the room temperature difference is negative, example :

Setting temperature (what you want) = 20°C.

Ambient temperature (what you read on a reliable

thermometer) = 18°C.

Difference measured = -2°C.

Important:

Before carrying out the calibration it is recommend-

ed

to wait for 4h after the setting temperature modification to

insure that the ambient temperature is stabilized.

Settings

Factory

settings

Comfort

setting

temperature

19°C

Keypad

lock

Disabled

Eco mode

temperature

lowering-

level

-

3,5°C

Frost protection temperature

7°C

Minimum set of Comfort

setting temperature

7°C

Maximum set of Comfort

setting temperature

30°C

Temperature

unit

°C

Automatic open window

detection Enabled

PIN code protection

Disabled

Value

of

the

code

0000

17

3 sec

.

To correct, then proceed as follows :

Sensor temperature = 24°C

(The measured temperature may be different due to the loca-

tion of the thermostat in the room).

Decrease the temperature measured by the ambient tempera-

ture sensor by 2°C by pressing .

In our example the measured temperature by the sensor goes

from 24°C to 22°C.

To validate, save the new value and exit the mode, press . To

exit the Expert settings, press 3 times.

The reset

to

zero of the

sensor

calibration

To put the value of the correction to "0", do the following :

1-

When the temperature measured by the sensor appears,

press or for at least 3 seconds.

2-

To

save

and

move

automatically

to

the

press .

To exit the Expert settings, press

3 times.

Important: These changes should be performed by

a

qualified staff, it should be performed in production or

on site during the first installation

SETTING THE POWER

2- If the room temperature difference is positive, example :

Setting temperature (what you want) = 19°C.

Ambient temperature (what you read on a reliable

thermometer) = 21°C.

Difference measured = +2 °C.

To correct, then proceed as follows :

Sensor temperature= 21°C.

(The measured temperature may be different due to the loca-

tion of the thermostat in the room).

To have a controller adapted to the radiator and estimate the

energy consumed, it is essential to set the power of the device.

1-

Pre-set value: 0W. Select a value between 0W and 1250W by

pressing or .

Increase the temperature measured by the ambient tempera-

ture sensor by 2°C by pressing .

In our example the measured temperature by the sensor goes

from 21°C to 23°C.

To

save

and

move

automatically

to

the

press .

2-

To save the Expert settings, press

3 times.

18

5

sec

.

RESTORING FACTORY SETTINGS

If the PIN code protection is disabled, the user, installer and ex-

pert settings are re-initialized:

1-

From the Power setting setting, press . appears

on the display. Important : The power supply of the device should be

cut when working on the electrical system only. The

load shedding does not be operated by an

additional system with mechanized power shutdown

(with contac

tor…). The load shedding with frequent

mechanized power shutdowns can cause deterioration

of

the

device

depending

of

the quality of switching

elements used. This type of deterioration would not

be covered by the manufacturer’s warranty.

IN CASE OF POWER CUT

2-

appears.

Press

or

to select

.

- In case of power shutdown or power off by the switch,

the

clock must be set again. All the other settings are automati-

cally and permanently saved.

=

Factory settings reset

=

Factory settings not reset

3-

Press the key for 5 seconds. The device returns to its ini-

tial configuration and goes back automatically to the Auto

mode.

The following factory values will be effective:

Operating

User

settings

Installer

settings

Experts

settings

To exit the Expert settings, press

3 times.

REMOTELY MANAGEMENT BY POWER

SHUTDOWN

Settings

Factory

settings

Comfort setting

temperature

19°C

Keypad

lock

Disabled

Eco mode

temperature

lowering-

level

-

3,5°C

Frost protection temperature

7°C

Minimum set of Comfort

setting temperature

7°C

Maximum set of Comfort

setting temperature

30°C

Temperature

unit

°C

Automatic open window

detection Enabled

PIN code protection

Disabled

Value

of

the

code

0000

Power

0W

19

5.

MAINTENANCE,

REPAIR AND DISPOSAL

•

WARNING: Disconnect electrical supply before carrying

out any maintenance activity.

•

The product can be cleaned using a soft damp cloth.

Do NOT use chemical or abrasive cleaners as they will

damage the surface finish.

•

The radiator is equipped with an overheat protection

that cannot be reset (melt fuse). This overheat protection

disconnects the current if the radiator becomes too hot

(e.g. when covered) or if, when freestanding, is knocked

over and left in this position.

•

If the supply cord is damaged, it must be replaced by

the manufacturer, his service agent or similar qualified

persons in order to avoid a hazard.

•

The radiator is filled with an exact amount of

environmental friendly vegetable oil. Any repairs that

require the radiator to be opened shall therefore only

be carried out by the manufacturer or his approved

agent. Please contact the manufacturer or his agent

in case of leakage.

•

When scrapping the radiator, follow the regulations

concerning the disposal of oil.

6.

WARRANTY

The product is covered by a 10 year warranty except for

the electrical and electronic components that are covered

by a 2 year warranty.

7.

TECHNICAL

CHARACTERISTICS

ENVIRONMENTAL

CONDITIONS:

-

Operating

temperature

-

Storage temperature

-30°C to +50°C

-30°C to +70°C

SETTING TEMPERATURE RANGE

-

Comfort mode

-

Frost protection mode

+5°C to +30°C

+7°C

ELECTRICAL INSULATION

Class I

ELECTRICAL

PROTECTION

IP

21

POWER SUPPLY

230 VAC – 50 Hz or 400

VAC - 50 Hz according to the

product rating label.

DIRECTIVES & STANDARDS:

The product has been designed

to comply with the following

Directives and Standards.

20

• EN 60730-1

• EN 60335-1

• EN 60335-2-30

• EN 62233

• EN 55014-1

• EN 55014-2

• EN 61000-3-2

• EN 61000-3-3

• EN 60529

• LV Directive 2014/35/EU

•EMC Directive 2014/30/EU

•RoHS Directive 2011/65/EU

•ECO Directive 2015/1188

GB GENERAL

INFORMATION

Leht laadib ...

Purmo Kaba2 paigaldusjuhend

Purmo Kaba2 paigaldusjuhend

teistes keeltes

Seotud paberid

Muud dokumendid